Arnd Bergmann [Thu, 20 Nov 2014 16:39:59 +0000 (17:39 +0100)]
Merge tag 'sunxi-dt-for-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/dt
Pull "Allwinner Device Tree Changes for 3.19" from Maxime Ripard:
A lot of things happened during that merge window, but mostly:
- Preliminary Support for the A80
- New Boards Support
+ Mele M3
+ Banana Pi
+ Optimus
+ OLinuXino Lime2
- Device Tree Relicensing to GPLv2/X11 dual license
* tag 'sunxi-dt-for-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux: (52 commits)
ARM: dts: sun6i: Add ethernet support to M9 board
ARM: sun6i: DT: Add PLL6 multiple outputs
ARM: dts: sun6i: Add support for the status led
ARM: dts: sun6i: Add EHCI support for the M9 board
ARM: dts: sunxi: Add regulator-boot-on property to ahci-5v regulator
ARM: dts: sun7i: Cubietruck: add power supply regulator for USB OTG VBUS
ARM: dts: sun7i: Cubietruck: override regulator pin
ARM: sun7i: dtsi: add support for usbphy0
ARM: dtsi: sunxi: add common VBUS regulator
ARM: dts: sunxi: Banana Pi: increase startup-delay for the GMAC PHY regulator
ARM: dts: sunxi: Use sun4i-a10-apb1-clk for sun6i/sun8i apb2 clocks.
ARM: dts: sunxi: unify APB1 clock
ARM: dts: sun6i: Re-parent ahb1_mux to pll6 as required by dma controller
ARM: sun5i: olinuxino: Relicense the device tree under GPLv2/X11
ARM: sun4i: cubieboard: Relicense the device tree under GPLv2/X11
ARM: sun7i: pcduino3: Relicense the device tree under GPLv2/X11
ARM: sun4i: pcduino: Relicense the device tree under GPLv2/X11
ARM: sun7i: olinuxino lime: Relicense the device tree under GPLv2/X11
ARM: dts: sun9i: Enable uart4 for A80 Optimus board
ARM: dts: sun9i: Add uart4 pinmux setting for A80 SoC
...
Arnd Bergmann [Thu, 20 Nov 2014 16:38:09 +0000 (17:38 +0100)]
Merge tag 'v3.19-meson-dts' of https://github.com/carlocaione/linux-meson into next/dt
Pull "ARM: meson: DTS related changes" from Carlo Caione:
here is the pull request for the DT related changes for the 3.19.
It's mainly the work done by Beniamino for the preliminary support of
the Amlogic Meson8 SoC, the support for L2 cache and the I2C
controller.
Please note that the support for the Tronsmart S89 Elite TV box has not
been included since the Meson8 development will be done now on a
different dev board kindly provided by Amlogic.
* tag 'v3.19-meson-dts' of https://github.com/carlocaione/linux-meson:
ARM: dts: meson: add I2C controller nodes
ARM: meson: DTS: enable L2 cache
ARM: dts: add dtsi for Amlogic Meson8 SoCs
DTS: meson: Add forgotten compatible in board DTS
Arnd Bergmann [Thu, 20 Nov 2014 12:45:22 +0000 (13:45 +0100)]
Merge tag 'v3.19-next-dts' of https://github.com/mbgg/linux-mediatek into next/dt
Pull "Add support for mt6592, mt8127 and mt8135 Socs from Mediatek"
from Matthias Brugger:
Here comes the pull request which introduces basic support for
Mediatek SoCs mt6592, mt8127 and mt8135.
The patches for the mt81xx got merged in the late tree for v3.18 but
were not be merged at the end. They got a small fix regarding the
compatible and model string in the dts files.
* tag 'v3.19-next-dts' of https://github.com/mbgg/linux-mediatek:
dt-bindings: add documentation for Mediatek SoC
ARM: mediatek: add dts for mt6592-evb
ARM: mediatek: Add basic support for mt6592
dt-bindings: add more chips in documentation for Mediatek SoC
ARM: dts: Build dtb for mt8127 & mt8135
ARM: mediatek: add dts for MT8135 evaluation board.
ARM: mediatek: Add basic support for mt8135
ARM: mediatek: add dts for 8127 Moose board
ARM: mediatek: Add basic support for mt8127
Arnd Bergmann [Thu, 20 Nov 2014 11:52:01 +0000 (12:52 +0100)]
Merge tag 'arm-soc/for-3.19/cygnus-dts-v2' of http://github.com/brcm/linux into next/dt
Pull "Broadcom Cygnus SoC Device Tree changes" from Florian Fainelli:
This pull request contains the Broadcom Cygnus Device Tree changes:
- binding documentation for the SoC and clock
- cygnus SoC and clock dtsi files
- DTS for Cygnus Entreprise phone, BCM911360K and BCM958300K
* tag 'arm-soc/for-3.19/cygnus-dts-v2' of http://github.com/brcm/linux:
ARM: dts: Enable Broadcom Cygnus SoC
dt-bindings: Document Broadcom Cygnus SoC and clocks
[arnd: something went wrong here, we already had pulled an earlier
version of the same patches, which had the wrong license statement.
I've pulled this one over the old pull request and fixed up the
conflicts now]
arch: arm: boot: dts: Correct vendor-prefix for iio device isl29028 in compatible property
This patch corrects the vendor-prefix for isl29028 in the compatible property from
"isil,isl29028" to "isl,isl29028" according to listed vendor-prefixes in
Documentation/devicetree/bindings/vendor-prefixes.txt. Incorrect vendor-prefix "isl"
was reported by checkpatch.pl warning for drivers/staging/iio/light/isl29028.c.
Thus incorrect vendor-prefix "isil" was corrected for every mention of device isl29028.
Staging: iio: light: Added correct vendor-prefix for device isl29028
This patch adds the correct vendor-prefix for device isl29028 and
maintains deprecated vendor-prefix found by checkpatch warning
for older kernel releases.
Signed-off-by: Darshana Padmadas <darshanapadmadas@gmail.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Mark Rutland <mark.rutland@arm.com> Acked-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
dt-bindings: Document deprecated device vendor name to fix related warning
This patch documents deprecated vendor name "isil" to fix warning of
undocumented string for device isl29028 as reported while running checkpatch.pl
on drivers/staging/iio/light/isl29028.c. This is done to maintain compatibility
with older kernels.
dt-bindings: Document correct and deprecated vendor-prefix with device isl29028
This patch documents the device isl29028 with its vendor-prefix. Undocumented deprecated vendor-prefix
found by checkpatch also documented for compatibility reasons.
Matthias Klein [Thu, 20 Nov 2014 10:52:45 +0000 (10:52 +0000)]
ARM: bcm2835: Add device tree for Raspberry Pi model B+
The model B and B+ differ in the GPIO lines for ACT and PWR leds, and the
I2S interface.
Signed-off-by: Matthias Klein <matthias.klein@linux.com> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Lee Jones <lee@kernel.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Wed, 19 Nov 2014 22:19:17 +0000 (23:19 +0100)]
Merge tag 'mvebu-dt-3.19' of git://git.infradead.org/linux-mvebu into next/dt
Pull "mvebu DT changes for v3.19" from Jason Cooper:
- mvebu
- ReadyNAS 102 leds, esata
- ReadyNAS 2120 esata
- Add cache-unified for Aurora L2 node
- Add ref clk for timer and watchdog on Armada 375
- Cleanup Armada XP pinctrl for GigE
- Add RGMII pinctrl, i2c eeprom, and fix 74hc595 counter on Lenovo ix4-300d
- kirkwood
- Add DLink DIR665 and it's DSA configuration
* tag 'mvebu-dt-3.19' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: armada-xp: Fix 74hc595 count for Lenovo ix4-300d
ARM: mvebu: armada-xp: Add I2C eeprom on Lenovo ix4-300d
ARM: mvebu: armada-xp: Add RGMII pinctrl to Lenovo ix4-300d
ARM: mvebu: armada-xp: Add GE0 pinctrl settings for GMII
ARM: mvebu: armada-xp: Move GE0/1 pinctrl settings for RGMII
ARM: mvebu: armada-xp: Use pinctrl node alias
ARM: mvebu: armada-xp: Add node alias to pinctrl and add base address
ARM: mvebu: armada-xp: Consolidate pinctrl node
ARM: Kirkwood: DIR665: Instantiate Distributed Switch Architecture
ARM: Kirkwood: Add support for DLink DIR665
ARM: mvebu: Enable rear eSATA ports of NETGEAR ReadyNAS 2120
ARM: mvebu: Enable the reference clock for timer and watchdog on Armada 375 SoC
arm: mvebu: Clarify (e)SATA ports info in NETGEAR ReadyNAS 102 .dts file
arm: mvebu: Fix LED color in NETGEAR ReadyNAS 102 .dts file
ARM: mvebu: Fix the Aurora L2 cache node with the required cache-unified property
Arnd Bergmann [Wed, 19 Nov 2014 22:11:12 +0000 (23:11 +0100)]
Merge tag 'hix5hd2-dt-for-3.19' of git://github.com/hisilicon/linux-hisi into next/dt
Pull "ARM: DT: Hisilicon terminal SoC HiX5HD2 DT updates for 3.19" from Wei Xu:
- Add reboot node, reusing syscon-reboot
- Add I2C nodes Hisilicon IP
- Add IR node based on Hisilicon IP
- Add Watchdog node based on ARM IP
- Add GPIO nodes based on ARM GPIO IP
- Add SATA node based on Hisilicon IP
- Add USB nodes
- Add MMC nodes based on Synopsys IP
- Add GMAC nodes based on Hisilicon IP
Arnd Bergmann [Wed, 19 Nov 2014 21:49:32 +0000 (22:49 +0100)]
Merge tag 'renesas-dt-cleanups3-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Pull "Third Round of Renesas ARM Based SoC DT Cleanups for v3.19" from Simon Horman:
* Use keyboard as gpio-keys node name
* tag 'renesas-dt-cleanups3-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: kzm9g-reference: Use keyboard as gpio-keys node name
ARM: shmobile: koelsch: Use keyboard as gpio-keys node name
ARM: shmobile: lager: Use keyboard as gpio-keys node name
ARM: shmobile: armadillo800eva: Use keyboard as gpio-keys node name
Arnd Bergmann [Wed, 19 Nov 2014 21:45:33 +0000 (22:45 +0100)]
Merge tag 'renesas-dt-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Pull "Renesas ARM Based SoC DT Updates for v3.19" from Simon Horman:
* Add Add SoC-specific SATA compatible property to r8a7779
* Enable DMA for MMCIF on r8a7791 and r8a7790
* Enable USB-PHY, HS-USB and USB3.0 on r8a7791 and r8a7790
* Enable TMU timer via DT on r8a7778
* Enable CMT timer via DT on r8a73a4
* Add MMP and {SR}GX clocks to r8a7791 and r8a7790
* Correct scifa2 clock index on r8a7740
* Add missing INTCA for irqpin on r8a7740
Peter Griffin [Mon, 17 Nov 2014 16:48:00 +0000 (17:48 +0100)]
ARM: STi: DT: STih407: STih410: Add clk_ignore_unused to kernel bootargs
At the moment we don't take a reference on some core interconnect
clocks which means when CCF turns off unused clocks the SoC will
hang. As a temp soltuion we will boot with clk_ignore_unused
parameter for all b2120 boards.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Peter Griffin [Mon, 17 Nov 2014 16:48:00 +0000 (17:48 +0100)]
ARM: STi: DT: STih407: Abstract common dt nodes into shared files.
The stih410 soc which will be added in the following commit is very similar to
the stih407, to enable maximum re-use of the dt files this commit abstracts the
common parts into a shared dt file stihxxx-b2120 for the board, and also a shared
file stih407-family.dtsi for the SoC.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org> Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Peter Griffin [Mon, 17 Nov 2014 16:47:00 +0000 (17:47 +0100)]
ARM: STi: DT: STiH410: Add defines for STiH410 DT clocks
Although most clock outputs are the same as stih407 SoC, stih410
also has some additional new clock outputs.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Peter Griffin [Mon, 17 Nov 2014 16:47:00 +0000 (17:47 +0100)]
ARM: STi: DT: STiH416: Add pinctl setup for usb controllers.
This patch adds the required pin config for all usb controllers
on the stih416.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Hans de Goede [Thu, 13 Nov 2014 09:31:48 +0000 (10:31 +0100)]
ARM: dts: sun6i: Add EHCI support for the M9 board
The Mele M9 / A1000G quad uses both usb-ports, one goes to an internal
usb wifi card, the other to a build-in usb-hub, so neither need their
OHCI companion controller to be enabled since the are always connected at
USB-2 speeds.
The controller which is attached to the wifi also does not need a vbus
regulator.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede [Thu, 13 Nov 2014 09:31:43 +0000 (10:31 +0100)]
ARM: dts: sunxi: Add regulator-boot-on property to ahci-5v regulator
This avoids it getting briefly turned off between when the regulator getting
registered and the ahci driver turning it back on, thus avoiding the disk
going into emergency head park mode.
Reported-by: Bruno Prémont <bonbons@linux-vserver.org> Tested-by: Bruno Prémont <bonbons@linux-vserver.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Nishanth Menon [Fri, 7 Nov 2014 17:47:13 +0000 (11:47 -0600)]
ARM: dts: Add am57xx-beagle-x15
BeagleBoard-X15 is the next generation Open Source Hardware
BeagleBoard based on TI's AM5728 SoC featuring dual core 1.5GHz A15
processor. The platform features 2GB DDR3L (w/dual 32bit busses),
eSATA, 3 USB3.0 ports, integrated HDMI (1920x1080@60), separate LCD
port, video In port, 4GB eMMC, uSD, Analog audio in/out, dual 1G
Ethernet.
For more information, refer to:
BeagleBoard-X15 Wiki:
http://www.elinux.org/Beagleboard:BeagleBoard-X15
AM5728 is part of the Sitara product family whose additional details
will be available: http://www.ti.com/lsds/ti/arm/overview.page
Technical Reference Manual for AM5728 is public domain at:
http://www.ti.com/lit/spruhz6
Just add basic support for the moment, the following updates are needed:
i) Ethernet - depends on SoC dts fixes
ii) USB Client (USB2) - depends on GPIO extcon
ii) HDMI - additional driver fixes pending
iii) Audio - additional driver fixes pending
NOTE:
AM5728 Data Manual (SPRS915L - August 2014) section 4.1.1 states: "All
unused power supply balls must be supplied with the voltages specified
in the Section 5.2, Recommended Operating Conditions". This implies
that all unused voltage rails for AM5728 can never be switched off even
if the hardware blocks inside that voltage domain is unused. Switching
off these unused rails may result in stability issues on other domains
and increased leakage and power-on-hour impacts.
Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Tom Rini <trini@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: OMAP2+: igep00x0: Add pdata-quirks for the btwilink device.
Add btwilink device for IGEPv2 Rev. F and IGEP COM MODULE Rev. G.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com> Acked-by: Javier Martinez Canillas <javier@dowhile0.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
We can't suppose that the i2c2 pins are configured as I2C bus, these pins are
connected to expansion connectors.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com> Acked-by: Javier Martinez Canillas <javier@dowhile0.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: omap3-igep0020-rev-f: Support IGEPv2 Rev. F
Add support for the new hardware revision of the IGEPv2. Basically, the new
revision F replaces the old Wifi module for a Wilink8 based module.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com> Acked-by: Javier Martinez Canillas <javier@dowhile0.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: omap3-igep0020-common: Introduce igep0020 common dtsi file.
Use the omap3-igep0020-common.dtsi file and remove repeated parts leaving
the nodes that are not common between IGEPv2 hardware revisions.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com> Acked-by: Javier Martinez Canillas <javier@dowhile0.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: omap3-igep0030-rev-g: Support IGEP COM MODULE Rev. G
Add support for the new hardware revision of the IGEP COM MODULE. Basically,
the new revision G replaces the old Wifi module for a Wilink8 based module.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com> Acked-by: Javier Martinez Canillas <javier@dowhile0.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: omap3-igep0030-common: Introduce igep0030 common dtsi file.
Use the omap3-igep0030-common.dtsi file and remove repeated parts leaving
the nodes that are not common between IGEP COM MODULE hardware revisions.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com> Acked-by: Javier Martinez Canillas <javier@dowhile0.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: omap3-igep00x0: Move outside common file the on board Wifi module.
New IGEP boards revisions will use another Wifi module, so this patch moves
the DT nodes outside the common omap3-igep.dtsi file to specific DT for every
board.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com> Acked-by: Javier Martinez Canillas <javier@dowhile0.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: omap3-igep0020: Specify IGEPv2 revision in device tree.
We'll introduce new hardware revisions soon. This patch is only to
indicate which board revision supports this device tree file in order
to avoid confusions.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com> Acked-by: Javier Martinez Canillas <javier@dowhile0.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: omap3-igep0030: Specify IGEP COM revision in device tree.
We'll introduce new hardware revisions soon. This patch is only to
indicate which board revision supports this device tree file in order
to avoid confusions.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com> Acked-by: Javier Martinez Canillas <javier@dowhile0.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: omap3-igep00x0: Move NAND configuration to a common place.
At this moment all supported boards use same NAND chip, so has more sense
move the GPMC and NAND configuration to the omap3-igep.dtsi common place.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com> Acked-by: Javier Martinez Canillas <javier@dowhile0.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: omap3-igep00x0: Fix UART2 pins that aren't common.
UART2 is used to connect the processor with the bluetooth chip, these pins
are not common between IGEPv2 boards and IGEP COM MODULE boards. This patch
muxes the correct pins for every board and removes UART2 configuration from
common omap3-igep.dtsi file.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com> Acked-by: Javier Martinez Canillas <javier@dowhile0.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
Karsten Merker [Tue, 11 Nov 2014 23:01:46 +0000 (00:01 +0100)]
ARM: dts: sunxi: Banana Pi: increase startup-delay for the GMAC PHY regulator
On the LeMaker Banana Pi, probing the external ethernet PHY connected
to the SoC's internal GMAC module sometimes fails. The PHY power
supply is handled via a GPIO-controlled regulator, and the existing
regulator startup-delay of 50000us is too short to make sure that the
PHY is always fully powered up when it is queried by phylib. Tests
have shown that to provide a reliable PHY detection, the startup-delay
has to be increased to at least 60000us. To have a certain safety margin
and to cater for manufacturing variations between different boards,
the delay gets set to 100000us as discussed on the linux-arm-kernel
mailinglist.
Signed-off-by: Karsten Merker <merker@debian.org> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Nishanth Menon [Tue, 21 Oct 2014 14:38:10 +0000 (09:38 -0500)]
ARM: dts: dra7-evm: Keep all VDD rails always-on
DRA7 Data Manual (SPRS857L - August 2014) section 4.1.1 states: "All
unused power supply balls must be supplied with the voltages specified
in the Section 5.2, Recommended Operating Conditions".
This implies that all unused voltage rails for Vayu can never be
switched off even if the hardware blocks inside that voltage domain is
unused. Switching off these unused rails may result in stability issues
on other domains and increased leakage and power-on-hour impacts.
J6eco-evm dts file already considers this, however j6evm-dts file needs
to be fixed to consider this constraint of the SoC.
Signed-off-by: Nishanth Menon <nm@ti.com> Acked-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Nishanth Menon [Tue, 21 Oct 2014 14:35:56 +0000 (09:35 -0500)]
ARM: dts: dra72-evm: Add MMC nodes
Add MMC1 and 2 nodes. MMC1 is SDcard and MMC2 is eMMC.
NOTE on MMC1 card detect: Ideally, we should be using in-built SDCD
support, but we dont have it yet. So, use the fact that control module
of DRA7 is setup such that no matter what mode one configures it, GPIO
option is always hardwired in - use GPIO mode for SDcard detection.
[peter.ujfalusi@ti.com]
The power line feeding the SD card is also used by other devices on the EVM.
Use generic name instead of mmc2_3v3 so when other devices want to use the
same regulator it will look a bit better.
Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Nishanth Menon [Tue, 21 Oct 2014 14:30:47 +0000 (09:30 -0500)]
ARM: dts: dra72-evm: Add power button node
With Commit adff5962fdd2 ("Input: introduce palmas-pwrbutton"), we can
now support tps power button as a event source - This is SW7 (PB/WAKE)
on the J6-evm.
Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
George Cherian [Tue, 21 Oct 2014 10:41:19 +0000 (13:41 +0300)]
ARM: dts: dra72-evm: Enable USB support for dra72-evm.
Add USB data and pinctrl for USB.
Signed-off-by: George Cherian <george.cherian@ti.com> Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Mugunthan V N [Tue, 21 Oct 2014 10:01:00 +0000 (15:31 +0530)]
ARM: dts: dra7: Add CPSW and MDIO module nodes for dra7
Add CPSW and MDIO related device tree data for DRA7XX and made as status
disabled. Phy-id, pinmux for active and sleep state needs to be added in
board dts files and enable the CPSW device.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Cc: devicetree@vger.kernel.org Reviewed-by: Tony Lindgren <tony@atomide.com> Tested-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Tony Lindgren <tony@atomide.com>
Cc: devicetree@vger.kernel.org Reviewed-by: Tony Lindgren <tony@atomide.com> Tested-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Tony Lindgren <tony@atomide.com>
Suman Anna [Mon, 3 Nov 2014 23:07:34 +0000 (17:07 -0600)]
ARM: dts: DRA7: Add interrupts property to mailbox nodes
Add the interrupts property to all the 13 mailbox nodes in
DRA7xx. The interrupts property information added is inline
with the expected values with the DRA7xx crossbar driver,
and is common to both DRA74x and DRA72x SoCs.
Do note that the mailbox 1 is only capable of generating out
3 interrupts, while all the remaining mailboxes have 4
interrupts each.
Signed-off-by: Suman Anna <s-anna@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Olof Johansson [Sun, 9 Nov 2014 00:59:39 +0000 (16:59 -0800)]
Merge tag 'nomadik-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into next/dt
Merge "Nomadik updates for the v3.19 series" from Linus Walleij:
Nomadik changes for the v3.19 development series:
- Rearrange the DTS files to make a pure SoC-specific file and
a pure board file for S8815.
- Add the device tree for the NDK15 board.
- Update the defconfig and configure in the STMPE expander by
default on the Nomadik.
* tag 'nomadik-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: nomadik: configure in STMPE support
ARM: update Nomadik config
ARM: nomadik: device tree for NHK15 board
ARM: nomadik: push ethernet down to board
ARM: nomadik: set up MCDATDIR2
ARM: nomadik: move GPIO I2C to S8815 board file
ARM: nomadik: disable chrystals in top level board files
ARM: nomadik: move MMC/SD card detect GPIO to board DTS
Olof Johansson [Sun, 9 Nov 2014 00:47:37 +0000 (16:47 -0800)]
Merge tag 'berlin-dt-3.19-1' of git://git.infradead.org/users/hesselba/linux-berlin into next/dt
Merge "ARM: berlin: DT changes for v3.19 (round 1)" from Sebastian Hesselbarth:
"This is Berlin DT changes for v3.19 and contains those patches that missed
the v3.18 merge window plus corresponding patches to catch-up with Antoine's
BG2Q improvements for BG2 and BG2CD. We now have working SDHCI and Ethernet
on all SoCs (well, BG2CD has HDMI HEC only), SATA PHY support for BG2 is still
pending."
Berlin DT changes for v3.19 (round 1)
- AHCI and SATA PHY nodes for BG2Q
- Reset controller binding docs
- Ethernet nodes for BG2, BG2CD
- SDHCI nodes for BG2, BG2CD
- Corresponding board changes to enable AHCI, Ethernet, SDHCI
* tag 'berlin-dt-3.19-1' of git://git.infradead.org/users/hesselba/linux-berlin:
ARM: dts: berlin: Enable eMMC on Sony NSZ-GS7
ARM: dts: berlin: Enable WiFi on Google Chromecast
ARM: dts: berlin: Add SDHCI controller nodes to BG2/BG2CD
ARM: dts: berlin: Enable ethernet on Sony NSZ-GS7
ARM: dts: berlin: Add phy-connection-type to BG2Q Ethernet
ARM: dts: berlin: Add BG2CD ethernet DT nodes
ARM: dts: berlin: Add BG2 ethernet DT nodes
ARM: dts: berlin: Add GPIO leds to Google Chromecast
ARM: dts: berlin: enable timer 1 for sched_clock
ARM: dts: berlin: add a required reset property in the chip controller node
Documentation: bindings: add reset bindings docs for Marvell Berlin SoCs
ARM: dts: berlin: enable the eSATA interface on the BG2Q DMP
ARM: dts: berlin: add the AHCI node for the BG2Q
Olof Johansson [Sun, 9 Nov 2014 00:39:12 +0000 (16:39 -0800)]
Merge tag 'sti-dt-for-v3.19-1' of git://git.stlinux.com/devel/kernel/linux-sti into next/dt
Merge "STi DT updates for v3.19, round 1" from Maxime Coquelin:
Highlights:
-----------
- Add SDHCI support for STiH41x B2020 boards
- Add reset controllers to STiH407 SoC
- Add MiPHY & SATA support to STiH416
- Add Thermal supportto STiH416
- Add Clock support to STiH407 SoC
This tag also includes STiH407 bindings definitions for reset controller.
* tag 'sti-dt-for-v3.19-1' of git://git.stlinux.com/devel/kernel/linux-sti:
ARM: STi: DT: STiH407: Fix: clk-tmds-hdmi clock is missing
ARM: STi: DT: STiH407: Add all defines for STiH407 DT clocks
ARM: STi: DT: STiH407: 407 DT Entry for clockgenA9
ARM: STi: DT: STiH407: 407 DT Entry for clockgen D0/D2/D3
ARM: STi: DT: STiH407: 407 DT Entry for clockgen C0
ARM: STi: DT: STiH407: 407 DT Entry for clockgen A0
ARM: DT: STi: STiH416: Add DT node for ST's SATA device
ARM: DT: STi: STiH416: Add DT node for MiPHY365x
ARM: STi: DT: STiH416: Supply Thermal Controller Device Tree nodes
ARM: STi: DT: Enable second sdhci controller for stih416 b2020 boards.
ARM: STi: DT: Enable mmc0 for both stih415 and stih416 SoCs
ARM: STi: DT: Add sdhci controller for stih415
ARM: STi: DT: Add sdhci pin configuration for stih415
ARM: STi: DT: Add sdhci controller for stih416
ARM: STi: DT: Add sdhci pins for stih416
ARM: sti: Add STiH407 reset controller support.
ARM: sti: Add STiH407 Kconfig entry to select STIH407_RESET
ARM: STi: DT: STiH41x: Convert all uppercase non-defines to lowercase
reset: stih407: Add reset controllers DT bindings
Olof Johansson [Sun, 9 Nov 2014 00:13:31 +0000 (16:13 -0800)]
Merge tag 'arm-soc/for-3.18/cygnus-dts-v9' of http://github.com/brcm/linux into next/dt
Merge "Broadcom Cygnus SoC Device Tree changes" from Florian Fianelli:
This patchset contains initial support for Broadcom's Cygnus SoC based on our
iProc architecture. Initial support is minimal and includes just the mach
platform code, clock driver, and a basic device tree configuration. Peripheral
drivers will be submitted soon, as will device tree configurations for other
Cygnus board variants.
These are the Device Tree changes
* tag 'arm-soc/for-3.18/cygnus-dts-v9' of http://github.com/brcm/linux:
ARM: dts: Enable Broadcom Cygnus SoC
dt-bindings: Document Broadcom Cygnus SoC and clocks
Chen-Yu Tsai [Thu, 6 Nov 2014 11:56:49 +0000 (19:56 +0800)]
ARM: dts: sun6i: Re-parent ahb1_mux to pll6 as required by dma controller
The dma controller requires that the ahb1 bus clock be driven by pll6
for peripheral access to work. Previously this was done in the dma
controller driver, but was since removed as part of a series to unify
the ahb1_mux and ahb1 clock drivers, in