Sasha Neftin [Sun, 6 Aug 2017 13:49:18 +0000 (16:49 +0300)]
e1000e: fix buffer overrun while the I219 is processing DMA transactions
Intel® 100/200 Series Chipset platforms reduced the round-trip
latency for the LAN Controller DMA accesses, causing in some high
performance cases a buffer overrun while the I219 LAN Connected
Device is processing the DMA transactions. I219LM and I219V devices
can fall into unrecovered Tx hang under very stressfully UDP traffic
and multiple reconnection of Ethernet cable. This Tx hang of the LAN
Controller is only recovered if the system is rebooted. Slightly slow
down DMA access by reducing the number of outstanding requests.
This workaround could have an impact on TCP traffic performance
on the platform. Disabling TSO eliminates performance loss for TCP
traffic without a noticeable impact on CPU performance.
Please, refer to I218/I219 specification update:
https://www.intel.com/content/www/us/en/embedded/products/networking/
ethernet-connection-i218-family-documentation.html
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com> Reviewed-by: Dima Ruinskiy <dima.ruinskiy@intel.com> Reviewed-by: Raanan Avargil <raanan.avargil@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Benjamin Poirier [Fri, 21 Jul 2017 18:36:27 +0000 (11:36 -0700)]
e1000e: Avoid receiver overrun interrupt bursts
When e1000e_poll() is not fast enough to keep up with incoming traffic, the
adapter (when operating in msix mode) raises the Other interrupt to signal
Receiver Overrun.
This is a double problem because 1) at the moment e1000_msix_other()
assumes that it is only called in case of Link Status Change and 2) if the
condition persists, the interrupt is repeatedly raised again in quick
succession.
Ideally we would configure the Other interrupt to not be raised in case of
receiver overrun but this doesn't seem possible on this adapter. Instead,
we handle the first part of the problem by reverting to the practice of
reading ICR in the other interrupt handler, like before commit 16ecba59bc33
("e1000e: Do not read ICR in Other interrupt"). Thanks to commit 0a8047ac68e5 ("e1000e: Fix msi-x interrupt automask") which cleared IAME
from CTRL_EXT, reading ICR doesn't interfere with RxQ0, TxQ0 interrupts
anymore. We handle the second part of the problem by not re-enabling the
Other interrupt right away when there is overrun. Instead, we wait until
traffic subsides, napi polling mode is exited and interrupts are
re-enabled.
Reported-by: Lennart Sorensen <lsorense@csclub.uwaterloo.ca> Fixes: 16ecba59bc33 ("e1000e: Do not read ICR in Other interrupt") Signed-off-by: Benjamin Poirier <bpoirier@suse.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
link_active = !hw->mac.get_link_status
/* link_active is false, wrongly */
This problem arises because the single flag get_link_status is used to
signal two different states: link status needs checking and link status is
down.
Avoid the problem by using the return value of .check_for_link to signal
the link status to e1000e_has_link().
Reported-by: Lennart Sorensen <lsorense@csclub.uwaterloo.ca> Signed-off-by: Benjamin Poirier <bpoirier@suse.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Benjamin Poirier [Fri, 21 Jul 2017 18:36:25 +0000 (11:36 -0700)]
e1000e: Fix return value test
All the helpers return -E1000_ERR_PHY.
Signed-off-by: Benjamin Poirier <bpoirier@suse.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Benjamin Poirier [Fri, 21 Jul 2017 18:36:24 +0000 (11:36 -0700)]
e1000e: Fix wrong comment related to link detection
Reading e1000e_check_for_copper_link() shows that get_link_status is set to
false after link has been detected. Therefore, it stays TRUE until then.
Signed-off-by: Benjamin Poirier <bpoirier@suse.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Benjamin Poirier [Fri, 21 Jul 2017 18:36:23 +0000 (11:36 -0700)]
e1000e: Fix error path in link detection
In case of error from e1e_rphy(), the loop will exit early and "success"
will be set to true erroneously.
Signed-off-by: Benjamin Poirier <bpoirier@suse.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Vhost-net has a hard limit on the number of zerocopy skbs in flight.
When reached, transmission stalls. Stalls cause latency, as well as
head-of-line blocking of other flows that do not use zerocopy.
Instead of stalling, revert to copy-based transmission.
Tested by sending two udp flows from guest to host, one with payload
of VHOST_GOODCOPY_LEN, the other too small for zerocopy (1B). The
large flow is redirected to a netem instance with 1MBps rate limit
and deep 1000 entry queue.
modprobe ifb
ip link set dev ifb0 up
tc qdisc add dev ifb0 root netem limit 1000 rate 1MBit
tc qdisc add dev tap0 ingress
tc filter add dev tap0 parent ffff: protocol ip \
u32 match ip dport 8000 0xffff \
action mirred egress redirect dev ifb0
Before the delay, both flows process around 80K pps. With the delay,
before this patch, both process around 400. After this patch, the
large flow is still rate limited, while the small reverts to its
original rate. See also discussion in the first link, below.
Without rate limiting, {1, 10, 100}x TCP_STREAM tests continued to
send at 100% zerocopy.
The limit in vhost_exceeds_maxpend must be carefully chosen. With
vq->num >> 1, the flows remain correlated. This value happens to
correspond to VHOST_MAX_PENDING for vq->num == 256. Allow smaller
fractions and ensure correctness also for much smaller values of
vq->num, by testing the min() of both explicitly. See also the
discussion in the second link below.
Changes
v1 -> v2
- replaced min with typed min_t
- avoid unnecessary whitespace change
Link:http://lkml.kernel.org/r/CAF=yD-+Wk9sc9dXMUq1+x_hh=3ThTXa6BnZkygP3tgVpjbp93g@mail.gmail.com
Link:http://lkml.kernel.org/r/20170819064129.27272-1-den@klaipeden.com Signed-off-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Biggers [Mon, 9 Oct 2017 21:30:52 +0000 (14:30 -0700)]
once: switch to new jump label API
Switch the DO_ONCE() macro from the deprecated jump label API to the new
one. The new one is more readable, and for DO_ONCE() it also makes the
generated code more icache-friendly: now the one-time initialization
code is placed out-of-line at the jump target, rather than at the inline
fallthrough case.
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: 66f5d6ce53e6 ("ipv6: replace rwlock with rcu and spinlock in fib6_table") Reported-by: Xiaolong Ye <xiaolong.ye@intel.com> Signed-off-by: Wei Wang <weiwan@google.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Tue, 10 Oct 2017 02:08:32 +0000 (19:08 -0700)]
Merge branch 'ppc-bundle' (bundle from Michael Ellerman)
Merge powerpc transactional memory fixes from Michael Ellerman:
"I figured I'd still send you the commits using a bundle to make sure
it works in case I need to do it again in future"
This fixes transactional memory state restore for powerpc.
* bundle'd patches from Michael Ellerman:
powerpc/tm: Fix illegal TM state in signal handler
powerpc/64s: Use emergency stack for kernel TM Bad Thing program checks
David S. Miller [Tue, 10 Oct 2017 01:12:03 +0000 (18:12 -0700)]
Merge branch '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2017-10-09
This series contains updates to i40e and i40evf only.
Jake fixes missed flag conversion from u64 to u32. Fixes a deafult ITR
value issue where the driver defaults to an ITR value of half the
expected value (in terms of minimum microseconds between interrupts). So
fix this by changing the default values to be calculated using the
ITR_REG_TO_USEC() macro which indicates that we are converting from the
register units into microseconds. Updates the drivers to bump the tail in
increments of 8 and double the number of descriptors we will bundle into
one tail bump when receiving. With the recent kernel support for
enabling XPS and QoS at the same time, we no longer need to worry about
the number of traffic classes when enabling XPS.
Lihong converts the use of hash_for_each() to hash_for_each_safe() to
safely remove a hash entry. Adds a check for the return value for
find_first_bit() in the case that it returns the size passed to search.
Alan fixes a bug in which filters are erroneously removed if they are
removed and then added again. So make sure that when adding a filter, if
we find it already existed in our list, make sure it is not marked to be
removed.
Jayaprakash adds the retrying of PHY reads when the I2C is busy for a
maximum period of 500ms.
Rami fixes code comment typo.
Stefano Brivio simplifies the code by removing the use of a local
return code variable and simply return the results of the read function.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 9 Oct 2017 23:38:52 +0000 (16:38 -0700)]
Merge branch '10GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
10GbE Intel Wired LAN Driver Updates 2017-10-09
This series contains updates to ixgbe only.
Emil fixes an issue where the semaphore bits could be stuck after a reset
or a crash, by adding the clearing of software resource bits in the
software/firmware synchronization register. Added error checks when we
attempt to identify and initialize the PHY to prevent a crash. Fixed a
few issues in the logic of ixgbe_clean_test_rings() which was exposed by
a previous commit that was causing a crash in ethtool diagnostics.
Bhumika Goyal fixes a couple of instances which were overlooked when we
made ixgbe_mac_operations constant.
Shannon Nelson fixes an issue to restore normal operations after the
last MACVLAN offload is removed, otherwise we get stuck in a single queue
operations.
The infamous Jesper Dangaard Brouer adds a counter which counts the
number of times the recycle fails and the real page allocator is invoked.
Alex updates the adaptive ITR algorithm to better support the needs of the
network. This attempt to make it so that our ITR algorithm will try to
prevent either starving a socket buffer for memory in the case of
transmit, or overrunning an receive socket buffer on receive. We should
function better with new features like XDP which can handle small packets
at high rates without needing to lock us into NAPI polling mode.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
1) Fix object leak on IPSEC offload failure, from Steffen Klassert.
2) Fix range checks in ipset address range addition operations, from
Jozsef Kadlecsik.
3) Fix pernet ops unregistration order in ipset, from Florian Westphal.
4) Add missing netlink attribute policy for nl80211 packet pattern
attrs, from Peng Xu.
5) Fix PPP device destruction race, from Guillaume Nault.
6) Write marks get lost when BPF verifier processes R1=R2 register
assignments, causing incorrect liveness information and less state
pruning. Fix from Alexei Starovoitov.
7) Fix blockhole routes so that they are marked dead and therefore not
cached in sockets, otherwise IPSEC stops working. From Steffen
Klassert.
8) Fix broadcast handling of UDP socket early demux, from Paolo Abeni.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (37 commits)
cdc_ether: flag the u-blox TOBY-L2 and SARA-U2 as wwan
net: thunderx: mark expected switch fall-throughs in nicvf_main()
udp: fix bcast packet reception
netlink: do not set cb_running if dump's start() errs
ipv4: Fix traffic triggered IPsec connections.
ipv6: Fix traffic triggered IPsec connections.
ixgbe: incorrect XDP ring accounting in ethtool tx_frame param
net: ixgbe: Use new PCI_DEV_FLAGS_NO_RELAXED_ORDERING flag
Revert commit 1a8b6d76dc5b ("net:add one common config...")
ixgbe: fix masking of bits read from IXGBE_VXLANCTRL register
ixgbe: Return error when getting PHY address if PHY access is not supported
netfilter: xt_bpf: Fix XT_BPF_MODE_FD_PINNED mode of 'xt_bpf_info_v1'
netfilter: SYNPROXY: skip non-tcp packet in {ipv4, ipv6}_synproxy_hook
tipc: Unclone message at secondary destination lookup
tipc: correct initialization of skb list
gso: fix payload length when gso_size is zero
mlxsw: spectrum_router: Avoid expensive lookup during route removal
bpf: fix liveness marking
doc: Fix typo "8023.ad" in bonding documentation
ipv6: fix net.ipv6.conf.all.accept_dad behaviour for real
...
cdc_ether: flag the u-blox TOBY-L2 and SARA-U2 as wwan
The u-blox TOBY-L2 is a LTE Cat 4 module with HSPA+ and 2G fallback.
This module allows switching to different USB profiles with the
'AT+UUSBCONF' command, and provides a ECM network interface when the
'AT+UUSBCONF=2' profile is selected.
The u-blox SARA-U2 is a HSPA module with 2G fallback. The default USB
configuration includes a ECM network interface.
Both these modules are controlled via AT commands through one of the
TTYs exposed. Connecting these modules may be done just by activating
the desired PDP context with 'AT+CGACT=1,<cid>' and then running DHCP
on the ECM interface.
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es> Signed-off-by: David S. Miller <davem@davemloft.net>
Lihong Yang [Thu, 7 Sep 2017 12:05:56 +0000 (08:05 -0400)]
i40e: use a local variable instead of calculating multiple times
The computed result of I40E_MAX_VSI_QP * I40E_VIRTCHNL_SUPPORTED_QTYPES
is used more than three times in function i40e_config_irq_link_list.
Simply declare a local variable to store it to improve readability.
Signed-off-by: Lihong Yang <lihong.yang@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i40e: Retry AQC GetPhyAbilities to overcome I2CRead hangs
- When the I2C is busy, the PHY reads are delayed. The firmware will
return EGAIN in these cases with an expectation that the SW will
trigger the reads again
- This patch retries the operation for a maximum period of 500ms
Signed-off-by: Jayaprakash Shanmugam <jayaprakash.shanmugam@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Lihong Yang [Thu, 7 Sep 2017 12:05:54 +0000 (08:05 -0400)]
i40e: add check for return from find_first_bit call
The find_first_bit function will return the size passed to search
if the first set bit is not found. This patch adds the check in case
that happens as the return value would be used as the index in an array
and that would have caused the out-of-bounds access.
Detected by CoverityScan, CID 1295969 Out-of-bounds access
Signed-off-by: Lihong Yang <lihong.yang@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Thu, 7 Sep 2017 12:05:53 +0000 (08:05 -0400)]
i40e: allow XPS with QoS enabled
Recently, the kernel gained support for enabling XPS and QoS at the
same time. Thus, we no longer need to worry about the number of
traffic classes when enabling XPS.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Thu, 7 Sep 2017 12:05:52 +0000 (08:05 -0400)]
i40e/i40evf: bundle more descriptors when allocating buffers
Double the number of descriptors we'll bundle into one tail bump when
receiving. Empirical testing has shown that we reduce CPU utilization
and don't appear to reduce throughput or packet rate. 32 seems to be the
sweet spot, as it's half the default polling budget, so we'd essentially
reduce from 4 tail writes when polling down to 2. Increasing this up to
64 appears to have negative impacts as it may become possible that we
don't bump the tail each time we get polled, which could cause a long
delay between returning descriptors to the hardware.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Thu, 7 Sep 2017 12:05:51 +0000 (08:05 -0400)]
i40e/i40evf: bump tail only in multiples of 8
Hardware only fetches descriptors on cachelines of 8, essentially
ignoring the lower 3 bits of the tail register. Thus, it is pointless to
bump tail by an unaligned access as the hardware will ignore some of the
new descriptors we allocated. Thus, it's ideal if we can ensure tail
writes are always aligned to 8.
At first, it seems like we'd already do this, since we allocate
descriptors in batches which are a multiple of 8. Since we'd always
increment by a multiple of 8, it seems like the value should always be
aligned.
However, this ignores allocation failures. If we fail to allocate
a buffer, our tail register will become unaligned. Once it has become
unaligned it will essentially be stuck unaligned until a buffer
allocation happens to fail at the exact amount necessary to re-align it.
We can do better, by simply rounding down the number of buffers we're
about to allocate (cleaned_count) such that "next_to_clean
+ cleaned_count" is rounded to the nearest multiple of 8.
We do this by calculating how far off that value is and subtracting it
from the cleaned_count. This essentially defers allocation of buffers if
they're going to be ignored by hardware anyways, and re-aligns our
next_to_use and tail values after a failure to allocate a descriptor.
This calculation ensures that we always align the tail writes in a way
the hardware expects and don't unnecessarily allocate buffers which
won't be fetched immediately.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Thu, 7 Sep 2017 12:05:50 +0000 (08:05 -0400)]
i40e: reduce lrxqthresh from 2 to 1
The lrxq thresh value tells hardware to immediately interrupt when there
are fewer than N*64 packets left in the ring.
Counter intuitively, empirical testing has shown that decreasing this
value from 2 to 1, and thus changing from an immediate interrupt at
fewer than 128 descriptors down to 64 descriptors causes a small
increase in the maximum total packets per second we can receive. This
increase occurs even when we're polling with interrupts masked, as the
hardware must still handle interrupts internally even if we've disabled
them in software.
Also reduce the value for any VFs we allocate.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Thu, 7 Sep 2017 12:05:49 +0000 (08:05 -0400)]
i40e/i40evf: always set the CLEARPBA flag when re-enabling interrupts
In the past we changed driver behavior to not clear the PBA when
re-enabling interrupts. This change was motivated by the flawed belief
that clearing the PBA would cause a lost interrupt if a receive
interrupt occurred while interrupts were disabled.
According to empirical testing this isn't the case. Additionally, the
data sheet specifically says that we should set the CLEARPBA bit when
re-enabling interrupts in a polling setup.
This reverts commit 40d72a509862 ("i40e/i40evf: don't lose interrupts")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Thu, 7 Sep 2017 12:05:48 +0000 (08:05 -0400)]
i40e/i40evf: fix incorrect default ITR values on driver load
The ITR register expects to be programmed in units of 2 microseconds.
Because of this, all of the drivers I40E_ITR_* constants are in terms of
this 2 microsecond register.
Unfortunately, the rx_itr_default value is expected to be programmed in
microseconds.
Effectively the driver defaults to an ITR value of half the expected
value (in terms of minimum microseconds between interrupts).
Fix this by changing the default values to be calculated using
ITR_REG_TO_USEC macro which indicates that we're converting from the
register units into microseconds.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alan Brady [Thu, 7 Sep 2017 12:05:47 +0000 (08:05 -0400)]
i40evf: fix mac filter removal timing issue
Due to the asynchronous nature in which mac filters are added and
deleted, there exists a bug in which filters are erroneously removed if
removed then added again quickly.
The events are as such:
- filter marked for removal
- same filter is re-added before watchdog that cleans up filters
- we skip re-adding the filter because we have it already in the
list
- watchdog filter cleanup kicks off and filter is removed
So when we were re-adding the same filter, it didn't actually get added
because it already existed in the list, but was marked for removal and
had yet to actually be removed.
This patch fixes the issue by making sure that when adding a filter, if
we find it already existing in our list, make sure it is not marked to
be removed.
Signed-off-by: Alan Brady <alan.brady@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Lihong Yang [Thu, 7 Sep 2017 12:05:46 +0000 (08:05 -0400)]
i40e: use the safe hash table iterator when deleting mac filters
This patch replaces hash_for_each function with hash_for_each_safe
when calling __i40e_del_filter. The hash_for_each_safe function is
the right one to use when iterating over a hash table to safely remove
a hash entry. Otherwise, incorrect values may be read from freed memory.
Detected by CoverityScan, CID 1402048 Read from pointer after free
Signed-off-by: Lihong Yang <lihong.yang@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Thu, 7 Sep 2017 22:19:12 +0000 (15:19 -0700)]
i40e: fix flags declaration
Since we don't yet have more than 32 flags, we'll use a u32 for both the
hw_features and flag field. Should we gain more flags in the future, we
may need to convert to a u64 or separate flags out into two fields.
This was overlooked in the previous commit 2781de2134c4 ("i40e/i40evf:
organize and re-number feature flags"), where the feature flag was not
converted form u64 to u32.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Reviewed-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
bugfixes:
- NFSv4/pnfs: Fix an infinite layoutget loop
- nfs: RPC_MAX_AUTH_SIZE is in bytes"
* tag 'nfs-for-4.14-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFSv4/pnfs: Fix an infinite layoutget loop
nfs/filelayout: fix oops when freeing filelayout segment
sunrpc: remove redundant initialization of sock
NFS: Fix uninitialized rpc_wait_queue
NFS: Cleanup error handling in nfs_idmap_request_key()
nfs: RPC_MAX_AUTH_SIZE is in bytes
Eric Dumazet [Mon, 9 Oct 2017 16:52:25 +0000 (09:52 -0700)]
ipv6: addrlabel: remove refcounting
After previous patch ("ipv6: addrlabel: rework ip6addrlbl_get()")
we can remove the refcount from struct ip6addrlbl_entry,
since it is no longer elevated in p6addrlbl_get()
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: thunderx: mark expected switch fall-throughs in nicvf_main()
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Cc: Sunil Goutham <sgoutham@cavium.com> Cc: Robert Richter <rric@kernel.org> Cc: linux-arm-kernel@lists.infradead.org Cc: netdev@vger.kernel.org Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 9 Oct 2017 17:36:25 +0000 (10:36 -0700)]
Merge branch '10GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-queue
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2017-10-09
This series contains updates to ixgbe and arch/Kconfig.
Mark fixes a case where PHY register access is not supported and we were
returning a PHY address, when we should have been returning -EOPNOTSUPP.
Sabrina Dubroca fixes the use of a logical "and" when it should have been
the bitwise "and" operator.
Ding Tianhong reverts the commit that added the Kconfig bool option
ARCH_WANT_RELAX_ORDER, since there is now a new flag
PCI_DEV_FLAGS_NO_RELAXED_ORDERING that has been added to indicate that
Relaxed Ordering Attributes should not be used for Transaction Layer
Packets. Then follows up with making the needed changes to ixgbe to
use the new PCI_DEV_FLAGS_NO_RELAXED_ORDERING flag.
John Fastabend fixes an issue in the ring accounting when the transmit
ring parameters are changed via ethtool when an XDP program is attached.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Tariq Toukan [Mon, 9 Oct 2017 13:59:50 +0000 (16:59 +0300)]
net/mlx4_en: Use __force to fix a sparse warning in TX datapath
In TX data-path, we intentionally do not byte-swap, as documented
in code and in the cited commit log.
This fixes sparse warning:
en_tx.c:720:23: warning: incorrect type in argument 1 (different base types)
en_tx.c:720:23: expected unsigned int [unsigned] [usertype] <noident>
en_tx.c:720:23: got restricted __be32 [usertype] doorbell_qpn
Fixes: 492f5add4be8 ("net/mlx4_en: Doorbell is byteswapped in Little Endian archs") Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tariq Toukan [Mon, 9 Oct 2017 13:59:49 +0000 (16:59 +0300)]
net/mlx4_core: Fix cast warning in fw.c
Fix the following SPARSE warning, in MLX4_GET() macro:
drivers/net/ethernet/mellanox/mlx4/fw.c:233:9: warning: cast to restricted __be64
Fixes: 17d5ceb6e43e ("net/mlx4_core: Fix unaligned accesses") Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tariq Toukan [Mon, 9 Oct 2017 13:59:48 +0000 (16:59 +0300)]
net/mlx4: Fix endianness issue in qp context params
Should take care of the endianness before assigning to params2 field.
Fixes: 53f33ae295a5 ("net/mlx4_core: Port aggregation upper layer interface") Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The reason is that both Thunderbolt bus and thunderbolt-net are build
into the kernel image, and the latter is linked first because
drivers/net comes before drivers/thunderbolt. Since both use
module_init() thunderbolt-net ends up calling Thunderbolt bus functions
too early triggering the above crash.
Fix this by moving Thunderbolt bus initialization to happen earlier to
make sure all the data structures are ready when Thunderbolt service
drivers are initialized. To be on the safe side also add a check for
properly initialized xdomain_property_dir to tb_register_property_dir().
Reported-by: kernel test robot <fengguang.wu@intel.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 9 Oct 2017 13:01:37 +0000 (06:01 -0700)]
ipv6: avoid zeroing per cpu data again
per cpu allocations are already zeroed, no need to clear them again.
Fixes: d52d3997f843f ("ipv6: Create percpu rt6_info") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Martin KaFai Lau <kafai@fb.com> Cc: Tejun Heo <tj@kernel.org> Acked-by: Tejun Heo <tj@kernel.org> Acked-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Mon, 9 Oct 2017 12:52:10 +0000 (14:52 +0200)]
udp: fix bcast packet reception
The commit bc044e8db796 ("udp: perform source validation for
mcast early demux") does not take into account that broadcast packets
lands in the same code path and they need different checks for the
source address - notably, zero source address are valid for bcast
and invalid for mcast.
As a result, 2nd and later broadcast packets with 0 source address
landing to the same socket are dropped. This breaks dhcp servers.
Since we don't have stringent performance requirements for ingress
broadcast traffic, fix it by disabling UDP early demux such traffic.
Reported-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Fixes: bc044e8db796 ("udp: perform source validation for mcast early demux") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
netlink: do not set cb_running if dump's start() errs
It turns out that multiple places can call netlink_dump(), which means
it's still possible to dereference partially initialized values in
dump() that were the result of a faulty returned start().
This fixes the issue by calling start() _before_ setting cb_running to
true, so that there's no chance at all of hitting the dump() function
through any indirect paths.
It also moves the call to start() to be when the mutex is held. This has
the nice side effect of serializing invocations to start(), which is
likely desirable anyway. It also prevents any possible other races that
might come out of this logic.
In testing this with several different pieces of tricky code to trigger
these issues, this commit fixes all avenues that I'm aware of.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Cc: Johannes Berg <johannes@sipsolutions.net> Reviewed-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
qed: Add iWARP support for unaligned MPA packets
This patch series adds support for handling unaligned MPA packets.
(FPDUs split over more than one tcp packet).
When FW detects a packet is unaligned it fowards the packet to
the driver via a light l2 dedicated connection. The driver then
stores this packet until the remainder of the packet is received.
Once the driver reconstructs the full FPDU, it sends it down
to fw via the ll2 connection. Driver also breaks down any packed
PDUs into separate packets for FW.
Patches 1-6 are all slight modifications to ll2 to support additional
requirements for the unaligned MPA ll2 client.
Patch 7 opens the additional ll2 connection for iWARP.
Patches 8-12 contain the algorithm for aligning packets.
====================
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com> Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kalderon [Mon, 9 Oct 2017 09:37:54 +0000 (12:37 +0300)]
qed: Add iWARP support for fpdu spanned over more than two tcp packets
We continue to maintain a maximum of three buffers per fpdu, to ensure
that there are enough buffers for additional unaligned mpa packets.
To support this, if a fpdu is split over more than two tcp packets, we
use an intermediate buffer to copy the data to the previous buffer, then
we can release the data. We need an intermediate buffer as the initial
buffer partial packet could be located at the end of the packet, not
leaving room for additional data. This is a corner case, and will usually
not be the case.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com> Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kalderon [Mon, 9 Oct 2017 09:37:53 +0000 (12:37 +0300)]
qed: Add support for MPA header being split over two tcp packets
There is a special case where an MPA header is split over to tcp
packets, in this case we need to wait for the next packet to
get the fpdu length. We use the incomplete_bytes to mark this
fpdu as a "special" one which requires updating the length with
the next packet
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com> Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kalderon [Mon, 9 Oct 2017 09:37:52 +0000 (12:37 +0300)]
qed: Add support for freeing two ll2 buffers for corner cases
When posting a packet on the ll2 tx, we can provide a cookie that
will be returned upon tx completion. This cookie is the ll2 iwarp buffer
which is then reposted to the rx ring. Part of the unaligned mpa flow
is determining when a buffer can be reposted. Each buffer needs to be
sent only once as a cookie for on the tx ring. In packed fpdu case, only
the last packet will be sent with the buffer, meaning we need to handle the
case that a cookie can be NULL on tx complete. In addition, when a fpdu
splits over two buffers, but there are no more fpdus on the second buffer,
two buffers need to be provided as a cookie. To avoid changing the ll2
interface to provide two cookies, we introduce a piggy buf pointer,
relevant for iWARP only, that holds a pointer to a second buffer that
needs to be released during tx completion.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com> Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kalderon [Mon, 9 Oct 2017 09:37:51 +0000 (12:37 +0300)]
qed: Add unaligned and packed packet processing
The fpdu data structure is preallocated per connection.
Each connection stores the current status of the connection:
either nothing pending, or there is a partial fpdu that is waiting for
the rest of the fpdu (incomplete bytes != 0).
The same structure is also used for splitting a packet when there are
packed fpdus. The structure is initialized with all data required
for sending the fpdu back to the FW. A fpdu will always be spanned across
a maximum of 3 tx bds. One for the header, one for the partial fdpu
received and one for the remainder (unaligned) packet.
In case of packed fpdu's, two fragments are used, one for the header
and one for the data.
Corner cases are not handled in the patch for clarity, and will be added
as a separate patch.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com> Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kalderon [Mon, 9 Oct 2017 09:37:50 +0000 (12:37 +0300)]
qed: Add mpa buffer descriptors for storing and processing mpa fpdus
The mpa buff is a descriptor for iwarp ll2 buffers that contains
additional information required for aligining fpdu's.
In some cases, an additional packet will arrive which will complete
the alignment of a fpdu, but we won't be able to post the fpdu due to
insufficient place on the tx ring. In this case we can't loose the data
and require storing it for later. Processing is therefore done
in two places, during rx completion, where we initialize a mpa buffer
descriptor and add it to the pending list, and during tx-completion, since
we free up an entry in the tx chain we can process any pending mpa packets.
The mpa buff descriptors are pre-allocated since we have to ensure that
we won't reach a state where we can't store an incoming unaligned packet.
All packets received on the ll2 MUST be processed by the driver at some
stage. Since they are preallocated, we hold a free list.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com> Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kalderon [Mon, 9 Oct 2017 09:37:49 +0000 (12:37 +0300)]
qed: Add ll2 connection for processing unaligned MPA packets
This patch adds only the establishment and termination of the
ll2 connection that handles unaligned MPA packets.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com> Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kalderon [Mon, 9 Oct 2017 09:37:48 +0000 (12:37 +0300)]
qed: Add LL2 slowpath handling
For iWARP unaligned MPA flow, a slowpath event of flushing an
MPA connection that entered an unaligned state is required.
The flush ramrod is received on the ll2 queue, and a pre-registered
callback function is called to handle the flush event.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com> Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kalderon [Mon, 9 Oct 2017 09:37:47 +0000 (12:37 +0300)]
qed: Add the source of a packet sent on an iWARP ll2 connection
When a packet is sent back to iWARP FW via the tx ll2 connection
the FW needs to know the source of the packet. Whether it is
OOO or unaligned MPA related. Since OOO is implemented entirely
inside the ll2 code (and shared with iSCSI), packets are marked
as IN_ORDER inside the ll2 code. For unaligned mpa the value
will be determined in the iWARP code and sent on the pkt->vlan
field.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com> Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kalderon [Mon, 9 Oct 2017 09:37:46 +0000 (12:37 +0300)]
qed: Fix initialization of ll2 offload feature
enable_ip_cksum, enable_l4_cksum, calc_ip_len were added in
commit stated below but not passed through to FW. This was OK
until now as it wasn't used, but is required for the iWARP
unaligned flow
Fixes:7c7973b2ae27 ("qed: LL2 to use packed information for tx")
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com> Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kalderon [Mon, 9 Oct 2017 09:37:45 +0000 (12:37 +0300)]
qed: Add ll2 option for dropping a tx packet
The option of sending a packet on the ll2 and dropping it exists in
hardware and was not used until now, thus not exposed.
The iWARP unaligned MPA flow requires this functionality for
flushing the tx queue.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com> Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kalderon [Mon, 9 Oct 2017 09:37:44 +0000 (12:37 +0300)]
qed: Add ll2 ability of opening a secondary queue
When more than one ll2 queue is opened ( that is not an OOO queue )
ll2 code does not have enough information to determine whether
the queue is the main one or not, so a new field is added to the
acquire input data to expose the control of determining whether
the queue is the main queue or a secondary queue.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com> Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kalderon [Mon, 9 Oct 2017 09:37:43 +0000 (12:37 +0300)]
qed: Add ll2 option to limit the number of bds per packet
iWARP uses 3 ll2 connections, the maximum number of bds is known
during connection setup. This patch modifies the static array in
the ll2_tx_packet descriptor to be a flexible array and
significantlly reduces memory size.
In addition, some redundant fields in the ll2_tx_packet were
removed, which also contributed to decreasing the descriptor size.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com> Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Similarly to a bridged port, the bridge device itself can be configured by
the user to be an mrouter port. In this case, all multicast traffic should
be forwarded to it. Make the mlxsw Spectrum driver offload these directives
to the Spectrum hardware.
Patches 1 and 2 add a new switchdev notification for bridge device mrouter
port status and make the bridge module notify about it.
Patches 3-5 change the mlxsw Spectrum driver to handle these notifications
by adding the Spectrum router port to the bridge MDB entries.
v1->v2:
- patch1:
- Don't add the MDB_RTR_TYPE_TEMP state and use the timer_pending to
distinguish between learning-on and learning-off states
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Yotam Gigi [Mon, 9 Oct 2017 09:15:35 +0000 (11:15 +0200)]
mlxsw: spectrum_switchdev: Support bridge mrouter notifications
Support the SWITCHDEV_ATTR_ID_BRIDGE_MROUTER port attribute switchdev
notification.
To do that, add the mrouter flag to struct mlxsw_sp_bridge_device, which
indicates whether the bridge device was set to be mrouter port. This field
is set when:
- A new bridge is created, where the value is taken from the kernel
bridge value.
- A switchdev SWITCHDEV_ATTR_ID_BRIDGE_MROUTER notification is sent.
In addition, change the bridge MID entries to include the router port when
the bridge device is configured to be mrouter port. The MID entries are
updated in the following cases:
- When a new MID entry is created, update the router port according to the
bridge mrouter state.
- When a SWITCHDEV_ATTR_ID_BRIDGE_MROUTER notification is sent, update all
the bridge's MID entries.
This is aligned with the case where a bridge slave is configured to be
mrouter port.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com> Reviewed-by: Nogah Frankel <nogahf@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yotam Gigi [Mon, 9 Oct 2017 09:15:34 +0000 (11:15 +0200)]
mlxsw: spectrum_switchdev: Add support for router port in SMID entries
In Spectrum, MDB entries point to MID entries, that indicate which ports a
packet should be forwarded to. Add the support in creating MID entries that
forward the packet to the Spectrum router port.
This will be later used to handle the bridge mrouter port switchdev
notifications.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com> Reviewed-by: Nogah Frankel <nogahf@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yotam Gigi [Mon, 9 Oct 2017 09:15:33 +0000 (11:15 +0200)]
mlxsw: spectrum: router: Export the mlxsw_sp_router_port function
In Spectrum hardware, the router port is a virtual port that is the gateway
to the routing mechanism. Hence, in order for a packet to be L3 forwarded,
it must first be L2 forwarded to the router port inside the hardware.
Further patches in this patchset are going to introduce support in bridge
device used as an mrouter port. In this case, the router port index will be
needed in order to update the MDB entries to include the router port. Thus,
export the mlxsw_sp_router_port function, which returns the index of the
Spectrum router port.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com> Reviewed-by: Nogah Frankel <nogahf@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yotam Gigi [Mon, 9 Oct 2017 09:15:32 +0000 (11:15 +0200)]
net: bridge: Export bridge multicast router state
Add an access function that, given a bridge netdevice, returns whether the
bridge device is currently an mrouter or not. The function uses the already
existing br_multicast_is_router function to check that.
This function is needed in order to allow ports that join an already
existing bridge to know the current mrouter state of the bridge device.
Together with the bridge device mrouter ports switchdev notifications, it
is possible to have full offloading of the semantics of the bridge device
mcast router state.
Due to the fact that the bridge multicast router status can change in
packet RX path, take the multicast_router bridge spinlock to protect the
read.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com> Reviewed-by: Nogah Frankel <nogahf@mellanox.com> Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yotam Gigi [Mon, 9 Oct 2017 09:15:31 +0000 (11:15 +0200)]
net: bridge: Notify on bridge device mrouter state changes
Add the SWITCHDEV_ATTR_ID_BRIDGE_MROUTER switchdev notification type, used
to indicate whether the bridge is or isn't mrouter. Notify when the bridge
changes its state, similarly to the already existing bridged port mrouter
notifications.
The notification uses the switchdev_attr.u.mrouter boolean flag to indicate
the current bridge mrouter status. Thus, it only indicates whether the
bridge is currently used as an mrouter or not, and does not indicate the
exact mrouter state of the bridge (learning, permanent, etc.).
Signed-off-by: Yotam Gigi <yotamg@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Emil Tantilov [Fri, 29 Sep 2017 17:55:42 +0000 (10:55 -0700)]
ixgbe: fix crash when injecting AER after failed reset
In case where AER recovery fails the device is left in a down state.
Consecutive AER error injection can lead to a double IRQ free.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Mon, 25 Sep 2017 21:55:36 +0000 (14:55 -0700)]
ixgbe: Update adaptive ITR algorithm
The following change is meant to update the adaptive ITR algorithm to
better support the needs of the network. Specifically with this change what
I have done is make it so that our ITR algorithm will try to prevent either
starving a socket buffer for memory in the case of Tx, or overrunning an Rx
socket buffer on receive.
In addition a side effect of the calculations used is that we should
function better with new features such as XDP which can handle small
packets at high rates without needing to lock us into NAPI polling mode.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Emil Tantilov [Mon, 11 Sep 2017 21:21:36 +0000 (14:21 -0700)]
ixgbe: fix the FWSM.PT check in ixgbe_mng_present()
Bits other than FWSM.PT can be set in IXGBE_SWFW_MODE_MASK making the
previous check invalid.
Change the check for MNG present to be only based on FWSM.PT bit.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Emil Tantilov [Mon, 11 Sep 2017 21:21:31 +0000 (14:21 -0700)]
ixgbe: fix use of uninitialized padding
This patch is resolving Coverity hits where padding in a structure could
be used uninitialized.
- Initialize fwd_cmd.pad/2 before ixgbe_calculate_checksum()
- Initialize buffer.pad2/3 before ixgbe_hic_unlocked()
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ixgbe: add counter for times Rx pages gets allocated, not recycled
The ixgbe driver have page recycle scheme based around the RX-ring
queue, where a RX page is shared between two packets. Based on the
refcnt, the driver can determine if the RX-page is currently only used
by a single packet, if so it can then directly refill/recycle the
RX-slot by with the opposite "side" of the page.
While this is a clever trick, it is hard to determine when this
recycling is successful and when it fails. Adding a counter, which is
available via ethtool --statistics as 'alloc_rx_page'. Which counts
the number of times the recycle fails and the real page allocator is
invoked. When interpreting the stats, do remember that every alloc
will serve two packets.
The counter is collected per rx_ring, but is summed and ethtool
exported as 'alloc_rx_page'. It would be relevant to know what
rx_ring that cannot keep up, but that can be exported later if
someone experience a need for this.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The QCA folks found another netlink problem - we were missing validation
of some attributes. It's not super problematic since one can only read a
few bytes beyond the message (and that memory must exist), but here's the
fix for it.
I thought perhaps we can make nla_parse_nested() require a policy, but
given the two-stage validation/parsing in regular netlink that won't work.
Please pull and let me know if there's any problem.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 9 Oct 2017 16:51:03 +0000 (09:51 -0700)]
Merge branch 'nfp-bpf-ABIv2-and-multi-port'
Jakub Kicinski says:
====================
nfp: bpf ABIv2 and multi port
This series migrates our eBPF offload from old PoC firmware to
a redesigned, faster and more feature rich FW. Marking support
is dropped for now. We have to teach the JIT about encoding
local memory accesses (one of NFP memory types). There is also
code to populate the ECC of instructions (PoC had ECC protection
on instruction store disabled). There is also a minor ld_field
fix and all 64 bit shifts can now be encoded.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Mon, 9 Oct 2017 04:04:17 +0000 (21:04 -0700)]
nfp: bpf: pass dst register to ld_field instruction
ld_field instruction is a bit special because the encoding uses
two source registers and one of them becomes the output. We do
need to pass the dst register to our encoding helpers though,
otherwise the "write both banks" flag will not be observed.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Mon, 9 Oct 2017 04:04:16 +0000 (21:04 -0700)]
nfp: bpf: byte swap the instructions
Device expects the instructions in little endian. Make sure we
byte swap on big endian hosts.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Mon, 9 Oct 2017 04:04:15 +0000 (21:04 -0700)]
nfp: bpf: pad code with valid nops
We need to append up to 8 nops after last instruction to make
sure the CPU will not fetch garbage instructions with invalid
ECC if the code store was not initialized.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Mon, 9 Oct 2017 04:04:14 +0000 (21:04 -0700)]
nfp: bpf: calculate code store ECC
In the initial PoC firmware I simply disabled ECC on the instruction
store. Do the ECC calculation for generated instructions in the driver.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Mon, 9 Oct 2017 04:04:13 +0000 (21:04 -0700)]
nfp: bpf: move to datapath ABI version 2
Datapath ABI version 2 stores the packet information in LMEM
instead of NNRs. We also have strict restrictions on which
GPRs we can use. Only GPRs 0-23 are reserved for BPF.
Adjust the static register locations and "ABI" registers.
Note that packet length is packed with other info so we have
to extract it into one of the scratch registers, OTOH since
LMEM can be used in restricted operands we don't have to
extract packet pointer.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Mon, 9 Oct 2017 04:04:12 +0000 (21:04 -0700)]
nfp: bpf: encode extended LM pointer operands
Most instructions have special fields which allow switching
between base and extended Local Memory pointers. Introduce
those to register encoding, we will use the extra LM pointers
to access high addresses of the stack.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Mon, 9 Oct 2017 04:04:11 +0000 (21:04 -0700)]
nfp: bpf: encode LMEM accesses
NFP LMEM is a large, indirectly accessed register file. There
are two basic indirect access registers. Each access operation
may either use offset (up to 8 or 16 words) or perform post
decrement/increment.
Add encodings of LMEM indexes as instruction operands.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Mon, 9 Oct 2017 04:04:10 +0000 (21:04 -0700)]
nfp: add more white space to the instruction defines
We need to add longer OP_* defines, move the values away.
Purely whitespace commit.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Mon, 9 Oct 2017 04:04:09 +0000 (21:04 -0700)]
nfp: bpf: remove packet marking support
Temporarily drop support for skb->mark. We are primarily focusing
on XDP offload, and implementing skb->mark on the new datapath has
lower priority.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Mon, 9 Oct 2017 04:04:08 +0000 (21:04 -0700)]
nfp: bpf: remove register rename
Remove the register renumbering optimization. To implement calling
map and other helpers we need more strict register layout. We can't
freely reassign register numbers.
This will have the effect of running in 4 context/thread mode, which
should be OK since we are moving towards integrating the BPF closer
with FW app datapath anyway, and the target datapath itself runs in
4 context mode.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Mon, 9 Oct 2017 04:04:07 +0000 (21:04 -0700)]
nfp: bpf: encode all 64bit shifts
Add encodings of all 64bit shift operations.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Mon, 9 Oct 2017 04:04:06 +0000 (21:04 -0700)]
nfp: bpf: move software reg helpers and cmd table out of translator
Move the software reg helpers and some static data to nfp_asm.c.
They are related to the previous patch, but move is done in a separate
commit for ease of review.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Mon, 9 Oct 2017 04:04:05 +0000 (21:04 -0700)]
nfp: bpf: use the power of sparse to check we encode registers right
Define a new __bitwise type for software representation of registers.
This will allow us to catch incorrect parameter types using sparse.
Accessors we define also allow us to return correct enum type and
therefore ensure all switches handle all register types.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Mon, 9 Oct 2017 04:04:04 +0000 (21:04 -0700)]
nfp: bpf: lift the single-port limitation
Limiting the eBPF offload to a single port was a workaround
required for the PoC application FW which has not been
released externally. It's not necessary any more.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Mon, 9 Oct 2017 04:04:03 +0000 (21:04 -0700)]
nfp: output control messages to trace_devlink_hwmsg()
Use standard devlink trace point to allow tracing of control
messages.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yunsheng Lin [Mon, 9 Oct 2017 07:43:59 +0000 (15:43 +0800)]
net: hns3: Cleanup for struct that used to send cmd to firmware
The hclge_tm module has already added _cmd to the end of struct
that used to send cmd to firmware. This will help us finding the
endian issues.
This patch adds the _cmd to the end of struct that used to send
cmd to firmware in hclge_main module.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
exposed some issues with the logic in the current implementation of
ixgbe_clean_test_rings() that are being addressed in this patch:
- Split the clearing of the Tx and Rx rings in separate loops. Previously
both Tx and Rx rings were cleared in a rx_desc->wb.upper.length based
loop which could lead to issues if for w/e reason packets were received
outside of the frames transmitted for the loopback test.
- Add check for IXGBE_TXD_STAT_DD to avoid clearing the rings if the
transmits have not comlpeted by the time we enter ixgbe_clean_test_rings()
- Exit early on ixgbe_check_lbtest_frame() failure.
This change fixes a crash during ethtool diagnostic (ethtool -t).
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A recent patch removed the dst_free() on the allocated
dst_entry in ipv4_blackhole_route(). The dst_free() marked the
dst_entry as dead and added it to the gc list. I.e. it was setup
for a one time usage. As a result we may now have a blackhole
route cached at a socket on some IPsec scenarios. This makes the
connection unusable.
Fix this by marking the dst_entry directly at allocation time
as 'dead', so it is used only once.
Fixes: b838d5e1c5b6 ("ipv4: mark DST_NOGC and remove the operation of dst_free()") Reported-by: Tobias Brunner <tobias@strongswan.org> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: David S. Miller <davem@davemloft.net>
A recent patch removed the dst_free() on the allocated
dst_entry in ipv6_blackhole_route(). The dst_free() marked
the dst_entry as dead and added it to the gc list. I.e. it
was setup for a one time usage. As a result we may now have
a blackhole route cached at a socket on some IPsec scenarios.
This makes the connection unusable.
Fix this by marking the dst_entry directly at allocation time
as 'dead', so it is used only once.
Fixes: 587fea741134 ("ipv6: mark DST_NOGC and remove the operation of dst_free()") Reported-by: Tobias Brunner <tobias@strongswan.org> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Emil Tantilov [Fri, 18 Aug 2017 22:48:02 +0000 (15:48 -0700)]
ixgbe: add error checks when initializing the PHY
Ignoring errors when attempting to identify the PHY can lead to a crash.
Specifically in the case of FW controlled PHYs where the PHY read/write
operations are set to NULL.
Removed redundant comment.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
projects / mirror_ubuntu-focal-kernel.git / log