Robert Richter [Wed, 20 Jun 2012 18:46:35 +0000 (20:46 +0200)]
perf/x86/amd: Unify AMD's generic and family 15h pmus
There is no need for keeping separate pmu structs. We can enable
amd_{get,put}_event_constraints() functions also for family 15h event.
The advantage is that there is only a single pmu struct for all AMD
cpus. This patch introduces functions to setup the pmu to enabe core
performance counters or counter constraints.
Also, cpuid checks are used instead of family checks where
possible. Thus, it enables the code independently of cpu families if
the feature flag is set.
Peter Zijlstra [Wed, 20 Jun 2012 09:11:38 +0000 (11:11 +0200)]
perf/x86: Fix USER/KERNEL tagging of samples
Several perf interrupt handlers (PEBS,IBS,BTS) re-write regs->ip but
do not update the segment registers. So use an regs->ip based test
instead of an regs->cs/regs->flags based test.
Reported-and-tested-by: Stephane Eranian <eranian@google.com> Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Frederic Weisbecker <fweisbec@gmail.com> Link: http://lkml.kernel.org/n/tip-xxrt0a1zronm1sm36obwc2vy@git.kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
Merge tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mturquette/linux
Pull fix to common clk framework from Michael Turquette:
"The previous set of common clk fixes for -rc5 left an uninitialized
int which could lead to bad array indexing when switching clock
parents. The issue is fixed with a trivial change to the code flow in
__clk_set_parent."
* tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mturquette/linux:
clk: fix parent validation in __clk_set_parent()
1) Fix RX sequence number handling in mwifiex, from Stone Piao.
2) Netfilter ipset mis-compares device names, fix from Florian
Westphal.
3) Fix route leak in ipv6 IPVS, from Eric Dumazet.
4) NFS fixes. Several buffer overflows in NCI layer from Dan
Rosenberg, and release sock OOPS'er fix from Eric Dumazet.
5) Fix WEP handling ath9k, we started using a bit the chip provides to
indicate undecrypted packets but that bit turns out to be unreliable
in certain configurations. Fix from Felix Fietkau.
6) Fix Kconfig dependency bug in wlcore, from Randy Dunlap.
7) New USB IDs for rtlwifi driver from Larry Finger.
8) Fix crashes in qmi_wwan usbnet driver when disconnecting, from Bjørn
Mork.
9) Gianfar driver programs coalescing settings properly in single queue
mode, but does not do so in multi-queue mode. Fix from Claudiu
Manoil.
10) Missing module.h include in davinci_cpdma.c, from Daniel Mack.
11) Need dummy handler for IPSET_CMD_NONE otherwise we crash in ipset if
we get this via nfnetlink, fix from Tomasz Bursztyka.
12) Missing RCU unlock in nfnetlink error path, also from Tomasz.
13) Fix divide by zero in igbvf when the user tries to set an RX
coalescing value of 0 usecs, from Mitch A Williams.
14) We can process SCTP sacks for the wrong transport, oops. Fix from
Neil Horman.
15) Remove hw IP payload checksumming from e1000e driver. This has zery
value in our stack, and turning it on creates a very unintuitive
restriction for users when using jumbo MTUs.
Specifically, when IP payload checksums are on you cannot use both
receive hashing offload and jumbo MTU. Fix from Bruce Allan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (27 commits)
e1000e: remove use of IP payload checksum
sctp: be more restrictive in transport selection on bundled sacks
igbvf: fix divide by zero
netfilter: nfnetlink: fix missing rcu_read_unlock in nfnetlink_rcv_msg
netfilter: ipset: fix crash if IPSET_CMD_NONE command is sent
davinci_cpdma: include linux/module.h
gianfar: Fix RXICr/TXICr programming for multi-queue mode
net: Downgrade CAP_SYS_MODULE deprecated message from error to warning.
net: qmi_wwan: fix Oops while disconnecting
mwifiex: fix memory leak associated with IE manamgement
ath9k: fix panic caused by returning a descriptor we have queued for reuse
mac80211: correct behaviour on unrecognised action frames
ath9k: enable serialize_regmode for non-PCIE AR9287
rtlwifi: rtl8192cu: New USB IDs
NFC: Return from rawsock_release when sk is NULL
iwlwifi: fix activating inactive stations
wlcore: drop INET dependency
ath9k: fix dynamic WEP related regression
NFC: Prevent multiple buffer overflows in NCI
netfilter: update location of my trees
...
floppy: cancel any pending fd_timeouts before adding a new one
In commit 070ad7e793dc ("floppy: convert to delayed work and
single-thread wq") the 'fd_timeout' timer was converted to a delayed
work. However, the "del_timer(&fd_timeout)" was lost in the process,
and any previous pending timeouts would stay active when we then
re-queued the timeout.
This resulted in the floppy probe sequence having a (stale) 20s timeout
rather than the intended 3s timeout, and thus made booting with the
floppy driver (but no actual floppy controller) take much longer than it
should.
Of course, there's little reason for most people to compile the floppy
driver into the kernel at all, which is why most people never noticed.
Canceling the delayed work where we used to do the del_timer() fixes the
issue, and makes the floppy probing use the proper new timeout instead.
The three second timeout is still very wasteful, but better than the 20s
one.
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull block bits from Jens Axboe:
"As vacation is coming up, thought I'd better get rid of my pending
changes in my for-linus branch for this iteration. It contains:
- Two patches for mtip32xx. Killing a non-compliant sysfs interface
and moving it to debugfs, where it belongs.
- A few patches from Asias. Two legit bug fixes, and one killing an
interface that is no longer in use.
- A patch from Jan, making the annoying partition ioctl warning a bit
less annoying, by restricting it to !CAP_SYS_RAWIO only.
- Three bug fixes for drbd from Lars Ellenberg.
- A fix for an old regression for umem, it hasn't really worked since
the plugging scheme was changed in 3.0.
- A few fixes from Tejun.
- A splice fix from Eric Dumazet, fixing an issue with pipe
resizing."
* 'for-linus' of git://git.kernel.dk/linux-block:
scsi: Silence unnecessary warnings about ioctl to partition
block: Drop dead function blk_abort_queue()
block: Mitigate lock unbalance caused by lock switching
block: Avoid missed wakeup in request waitqueue
umem: fix up unplugging
splice: fix racy pipe->buffers uses
drbd: fix null pointer dereference with on-congestion policy when diskless
drbd: fix list corruption by failing but already aborted reads
drbd: fix access of unallocated pages and kernel panic
xen/blkfront: Add WARN to deal with misbehaving backends.
blkcg: drop local variable @q from blkg_destroy()
mtip32xx: Create debugfs entries for troubleshooting
mtip32xx: Remove 'registers' and 'flags' from sysfs
blkcg: fix blkg_alloc() failure path
block: blkcg_policy_cfq shouldn't be used if !CONFIG_CFQ_GROUP_IOSCHED
block: fix return value on cfq_init() failure
mtip32xx: Remove version.h header file inclusion
xen/blkback: Copy id field when doing BLKIF_DISCARD.
The below commit introduced a bug in __clk_set_parent()
which could cause it to *skip* the parent validation
which makes sure the parent passed to the api is a valid
one.
This was identified by the following compiler warning..
drivers/clk/clk.c: In function '__clk_set_parent':
drivers/clk/clk.c:1083:5: warning: 'i' may be used uninitialized in this function [-Wuninitialized]
.. as reported by Marc Kleine-Budde.
There were various options discussed on how to fix this, one
being initing 'i' to clk->num_parents, but the below approach
was found to be more appropriate as it also makes the 'parent
validation' code simpler to read.
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Rajendra Nayak <rnayak@ti.com> Signed-off-by: Mike Turquette <mturquette@linaro.org> Cc: stable@kernel.org
Merge tag 'sound-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Just a few driver-specific fixes for ASoC and HD-audio."
* tag 'sound-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Fix no sound from ALC662 after Windows reboot
ASoC: tlv320aic3x: Fix codec pll configure bug
ASoC: wm2200: Add missing BCLK rate
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"One regression fix, two radeon fixes (one for an oops), and an i915
fix to unload framebuffers earlier.
We originally were going to leave the i915 fix until -next, but grub2
in some situations causes vesafb/efifb to be loaded now, and this
causes big slowdowns, and I have reports in rawhide I'd like to have
fixed."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/i915: kick any firmware framebuffers before claiming the gtt
drm: edid: Don't add inferred modes with higher resolution
drm/radeon: fix rare segfault
drm/radeon: fix VM page table setup on SI
Merge tag 'md-3.5-fixes' of git://neil.brown.name/md
Pull md fixes from NeilBrown:
"md: collection of bug fixes for 3.5
You go away for 2 weeks vacation and what do you get when you come
back? Piles of bugs :-)
Some found by inspection, some by testing, some during use in the
field, and some while developing for the next window..."
* tag 'md-3.5-fixes' of git://neil.brown.name/md:
md: fix up plugging (again).
md: support re-add of recovering devices.
md/raid1: fix bug in read_balance introduced by hot-replace
raid5: delayed stripe fix
md/raid456: When read error cannot be recovered, record bad block
md: make 'name' arg to md_register_thread non-optional.
md/raid10: fix failure when trying to repair a read error.
md/raid5: fix refcount problem when blocked_rdev is set.
md:Add blk_plug in sync_thread.
md/raid5: In ops_run_io, inc nr_pending before calling md_wait_for_blocked_rdev
md/raid5: Do not add data_offset before call to is_badblock
md/raid5: prefer replacing failed devices over want-replacement devices.
md/raid10: Don't try to recovery unmatched (and unused) chunks.
Milan Broz [Tue, 3 Jul 2012 11:55:41 +0000 (12:55 +0100)]
dm: verity fix documentation
Veritysetup is now part of cryptsetup package.
Remove on-disk header description (which is not parsed in kernel)
and point users to cryptsetup where it the format is documented.
Mention units for block size paramaters.
Fix target line specification and dmsetup parameters.
Signed-off-by: Milan Broz <mbroz@redhat.com> Cc: stable@kernel.org Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Mike Snitzer [Tue, 3 Jul 2012 11:55:37 +0000 (12:55 +0100)]
dm persistent data: fix allocation failure in space map checker init
If CONFIG_DM_DEBUG_SPACE_MAPS is enabled and memory is fragmented and a
sufficiently-large metadata device is used in a thin pool then the space
map checker will fail to allocate the memory it requires.
Switch from kmalloc to vmalloc to allow larger virtually contiguous
allocations for the space map checker's internal count arrays.
Reported-by: Vivek Goyal <vgoyal@redhat.com> Cc: stable@kernel.org Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Mike Snitzer [Tue, 3 Jul 2012 11:55:35 +0000 (12:55 +0100)]
dm persistent data: handle space map checker creation failure
If CONFIG_DM_DEBUG_SPACE_MAPS is enabled and dm_sm_checker_create()
fails, dm_tm_create_internal() would still return success even though it
cleaned up all resources it was supposed to have created. This will
lead to a kernel crash:
Joe Thornber [Tue, 3 Jul 2012 11:55:31 +0000 (12:55 +0100)]
dm thin: commit metadata before creating metadata snapshot
Userland sometimes sees a corrupt metadata block if metadata is changing
rapidly when a metadata snapshot is reserved for userland, To make the
problem go away, commit before we take the metadata snapshot (which is a
sensible thing to do anyway).
The checksums mean userland spots this corruption immediately so there's
no risk of acting on incorrect data. No corruption exists from the
kernel's point of view, and thin_check passes after pool shutdown.
I believe this is to do with shared blocks at the first level of the
{device, mapping} btree. Prior to the metadata-snap support no sharing
at this level was possible, so this patch is only required after commit cc8394d86f045b86ff303d3c9e4ce47d97148951 ("dm thin: provide userspace
access to pool metadata").
Signed-off-by: Joe Thornber <ejt@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Paul Mundt [Mon, 2 Jul 2012 05:34:11 +0000 (14:34 +0900)]
security: Fix nommu build.
The security + nommu configuration presently blows up with an undefined
reference to BDI_CAP_EXEC_MAP:
security/security.c: In function 'mmap_prot':
security/security.c:687:36: error: dereferencing pointer to incomplete type
security/security.c:688:16: error: 'BDI_CAP_EXEC_MAP' undeclared (first use in this function)
security/security.c:688:16: note: each undeclared identifier is reported only once for each function it appears in
include backing-dev.h directly to fix it up.
Signed-off-by: Paul Mundt <lethal@linux-sh.org> Signed-off-by: James Morris <james.l.morris@oracle.com>
Daniel Vetter [Sun, 1 Jul 2012 15:09:42 +0000 (17:09 +0200)]
drm/i915: kick any firmware framebuffers before claiming the gtt
Especially vesafb likes to map everything as uc- (yikes), and if that
mapping hangs around still while we try to map the gtt as wc the
kernel will downgrade our request to uc-, resulting in abyssal
performance.
Unfortunately we can't do this as early as readon does (i.e. as the
first thing we do when initializing the hw) because our fb/mmio space
region moves around on a per-gen basis. So I've had to move it below
the gtt initialization, but that seems to work, too. The important
thing is that we do this before we set up the gtt wc mapping.
Now an altogether different question is why people compile their
kernels with vesafb enabled, but I guess making things just work isn't
bad per se ...
v2:
- s/radeondrmfb/inteldrmfb/
- fix up error handling
v3: Kill #ifdef X86, this is Intel after all. Noticed by Ben Widawsky.
v4: Jani Nikula complained about the pointless bool primary
initialization.
v5: Don't oops if we can't allocate, noticed by Chris Wilson.
v6: Resolve conflicts with agp rework and fixup whitespace.
Backport to 3.5 -fixes queue requested by Dave Airlie - due to grub
using vesa on fedora their initrd seems to load vesafb before loading
the real kms driver. So tons more people actually experience a
dead-slow gpu. Hence also the Cc: stable.
Cc: stable@vger.kernel.org Reported-and-tested-by: "Kilarski, Bernard R" <bernard.r.kilarski@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Dave Airlie <airlied@redhat.com>
drm: edid: Don't add inferred modes with higher resolution
When a monitor EDID doesn't give the preferred bit, driver assumes
that the mode with the higest resolution and rate is the preferred
mode. Meanwhile the recent changes for allowing more modes in the
GFT/CVT ranges give actually more modes, and some modes may be over
the native size. Thus such a mode would be picked up as the preferred
mode although it's no native resolution.
For avoiding such a problem, this patch limits the addition of
inferred modes by checking not to be greater than other modes.
Also, it checks the duplicated mode entry at the same time.
Reviewed-by: Adam Jackson <ajax@redhat.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Dave Airlie <airlied@redhat.com>
In gem idle/busy ioctl the radeon object was derefenced after
drm_gem_object_unreference_unlocked which in case the object
have been destroyed lead to use of a possibly free pointer with
possibly wrong data.
Signed-off-by: Jerome Glisse <jglisse@redhat.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
The value returned by "mddev_check_plug" is only valid until the
next 'schedule' as that will unplug things. This could happen at any
call to mempool_alloc.
So just calling mddev_check_plug at the start doesn't really make
sense.
So call it just before, or just after, queuing things for the thread.
As the action that happens at unplug is to wake the thread, this makes
lots of sense.
If we cannot add a plug (which requires a small GFP_ATOMIC alloc) we
wake thread immediately.
RAID5 is a bit different. Requests are queued for the thread and the
thread is woken by release_stripe. So we don't need to wake the
thread on failure.
However the thread doesn't perform certain actions when there is any
active plug, so it is important to install a plug before waking the
thread. So for RAID5 we install the plug *before* queuing the request
and waking the thread.
Without this patch it is possible for raid1 or raid10 to queue a
request without then waking the thread, resulting in the array locking
up.
Also change raid10 to only flush_pending_write when there are not
active plugs, just like raid1.
This patch is suitable for 3.0 or later. I plan to submit it to
-stable, but I'll like to let it spend a few weeks in mainline
first to be sure it is completely safe.
We currently only allow a device to be re-added if it appear to be
in-sync. This is overly restrictive as it may be desirable to re-add
a device that is in the middle of recovery.
So remove the test for "InSync" - the test on rdev->raid_disk is
sufficient to ensure that the re-add will succeed.
Reported-by: Alexander Lyakas <alex.bolshoy@gmail.com> Tested-by: Alexander Lyakas <alex.bolshoy@gmail.com> Signed-off-by: NeilBrown <neilb@suse.de>
md/raid1: fix bug in read_balance introduced by hot-replace
When we added hot_replace we doubled the number of devices
that could be in a RAID1 array. So we doubled how far read_balance
would search. Unfortunately we didn't double the point at which
it looped back to the beginning - so it effectively loops over
all non-replacement disks twice.
This doesn't cause bad behaviour, but it pointless and means we
never read from replacement devices.
Shaohua Li [Tue, 3 Jul 2012 05:57:19 +0000 (15:57 +1000)]
raid5: delayed stripe fix
There isn't locking setting STRIPE_DELAYED and STRIPE_PREREAD_ACTIVE bits, but
the two bits have relationship. A delayed stripe can be moved to hold list only
when preread active stripe count is below IO_THRESHOLD. If a stripe has both
the bits set, such stripe will be in delayed list and preread count not 0,
which will make such stripe never leave delayed list.
Signed-off-by: Shaohua Li <shli@fusionio.com> Signed-off-by: NeilBrown <neilb@suse.de>
md: make 'name' arg to md_register_thread non-optional.
Having the 'name' arg optional and defaulting to the current
personality name is no necessary and leads to errors, as when
changing the level of an array we can end up using the
name of the old level instead of the new one.
So make it non-optional and always explicitly pass the name
of the level that the array will be.
in 3.1 added "r10_sync_page_io" which takes an IO size in sectors.
But we were passing the IO size in bytes!!!
This resulting in bio_add_page failing, and empty request being sent
down, and a consequent BUG_ON in scsi_lib.
[fix missing space in error message at same time]
This fix is suitable for 3.1.y and later.
Cc: stable@vger.kernel.org Reported-by: Christian Balzer <chibi@gol.com> Signed-off-by: NeilBrown <neilb@suse.de>
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull a couple more powerpc fixes from Benjamin Herrenschmidt:
"Here are two more fixes that I "missed" when scrubbing patchwork last
week which are worth still having in 3.5."
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/kvm: sldi should be sld
powerpc/xmon: Use cpumask iterator to avoid warning
fixed a hang, but introduced a refcounting in-balance so
that if the presence of bad-blocks ever caused an rdev to
be 'blocked' we would increment the refcount on the rdev and
never decrement it.
So added the needed rdev_dec_pending when md_wait_for_blocked_rdev
is not called.
md/raid5: In ops_run_io, inc nr_pending before calling md_wait_for_blocked_rdev
In ops_run_io(), the call to md_wait_for_blocked_rdev will decrement
nr_pending so we lose the reference we hold on the rdev.
So atomic_inc it first to maintain the reference.
This bug was introduced by commit 73e92e51b7969ef5477d
md/raid5. Don't write to known bad block on doubtful devices.
which appeared in 3.0, so patch is suitable for stable kernels since
then.
majianpeng [Tue, 12 Jun 2012 00:31:10 +0000 (08:31 +0800)]
md/raid5: Do not add data_offset before call to is_badblock
In chunk_aligned_read() we are adding data_offset before calling
is_badblock. But is_badblock also adds data_offset, so that is bad.
So move the addition of data_offset to after the call to
is_badblock.
This bug was introduced by commit 31c176ecdf3563140e639
md/raid5: avoid reading from known bad blocks.
which first appeared in 3.0. So that patch is suitable for any
-stable kernel from 3.0.y onwards. However it will need minor
revision for most of those (as the comment didn't appear until
recently).
md/raid5: prefer replacing failed devices over want-replacement devices.
If a RAID5 has both a failed device and a device marked as
'WantReplacement', then we should preferentially replace the failed
device.
However the current code replaces whichever is found first.
So split into 2 loops, check fail failed/missing first, and only check
for WantReplacement if nothing is failed or missing.
md/raid10: Don't try to recovery unmatched (and unused) chunks.
If a RAID10 has an odd number of chunks - as might happen when there
are an odd number of devices - the last chunk has no pair and so is
not mirrored. We don't store data there, but when recovering the last
device in an array we retry to recover that last chunk from a
non-existent location. This results in an error, and the recovery
aborts.
When we get to that last chunk we should just stop - there is nothing
more to do anyway.
This bug has been present since the introduction of RAID10, so the
patch is appropriate for any -stable kernel.
Cc: stable@vger.kernel.org Reported-by: Christian Balzer <chibi@gol.com> Tested-by: Christian Balzer <chibi@gol.com> Signed-off-by: NeilBrown <neilb@suse.de>
Anton Blanchard [Thu, 28 Jun 2012 19:28:57 +0000 (19:28 +0000)]
powerpc/xmon: Use cpumask iterator to avoid warning
We have a bug report where the kernel hits a warning in the cpumask
code:
WARNING: at include/linux/cpumask.h:107
Which is:
WARN_ON_ONCE(cpu >= nr_cpumask_bits);
The backtrace is:
cpu_cmd
cmds
xmon_core
xmon
die
xmon is iterating through 0 to NR_CPUS. I'm not sure why we are still
open coding this but iterating above nr_cpu_ids is definitely a bug.
This patch iterates through all possible cpus, in case we issue a
system reset and CPUs in an offline state call in.
Perhaps the old code was trying to handle CPUs that were in the
partition but were never started (eg kexec into a kernel with an
nr_cpus= boot option). They are going to die way before we get into
xmon since we haven't set any kernel state up for them.
Signed-off-by: Anton Blanchard <anton@samba.org> CC: <stable@kernel.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Merge branch 'fixes' of git://git.linaro.org/people/rmk/linux-arm
Pull two ARM fixes from Russell King:
"It's been fairly quiet with the fixes. Just two this time. One fixes
a long standing problem with KALLSYMS needing an additional pass, and
the other sorts a problem with the vmalloc space interacting with
static IO mappings."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7438/1: fill possible PMD empty section gaps
ARM: 7428/1: Prevent KALLSYM size mismatch on ARM.
Microcode reloading in a per-core manner is a very bad idea for both
major x86 vendors. And the thing is, we have such interface with which
we can end up with different microcode versions applied on different
cores of an otherwise homogeneous wrt (family,model,stepping) system.
So turn off the possibility of doing that per core and allow it only
system-wide.
This is a minimal fix which we'd like to see in stable too thus the
more-or-less arbitrary decision to allow system-wide reloading only on
the BSP:
Also, allowing the reload only from one CPU (the BSP in
that case) doesn't allow the reload procedure to degenerate
into an O(n^2) deal when triggering reloads from all
/sys/devices/system/cpu/cpuX/microcode/reload sysfs nodes
simultaneously.
A more generic fix will follow.
Cc: Henrique de Moraes Holschuh <hmh@hmh.eng.br> Cc: Peter Zijlstra <peterz@infradead.org> Signed-off-by: Borislav Petkov <borislav.petkov@amd.com> Link: http://lkml.kernel.org/r/1340280437-7718-2-git-send-email-bp@amd64.org Signed-off-by: H. Peter Anvin <hpa@zytor.com> Cc: <stable@vger.kernel.org>
Nicolas Pitre [Wed, 27 Jun 2012 16:28:57 +0000 (17:28 +0100)]
ARM: 7438/1: fill possible PMD empty section gaps
On ARM with the 2-level page table format, a PMD entry is represented by
two consecutive section entries covering 2MB of virtual space.
However, static mappings always were allowed to use separate 1MB section
entries. This means in practice that a static mapping may create half
populated PMDs via create_mapping().
Since commit 0536bdf33f (ARM: move iotable mappings within the vmalloc
region) those static mappings are located in the vmalloc area. We must
ensure no such half populated PMDs are accessible once vmalloc() or
ioremap() start looking at the vmalloc area for nearby free virtual
address ranges, or various things leading to a kernel crash will happen.
Signed-off-by: Nicolas Pitre <nico@linaro.org> Reported-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Tested-by: "R, Sricharan" <r.sricharan@ti.com> Reviewed-by: Catalin Marinas <catalin.marinas@arm.com> Cc: stable@vger.kernel.org Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Bruce Allan [Sat, 30 Jun 2012 20:02:42 +0000 (20:02 +0000)]
e1000e: remove use of IP payload checksum
Currently only used when packet split mode is enabled with jumbo frames,
IP payload checksum (for fragmented UDP packets) is mutually exclusive with
receive hashing offload since the hardware uses the same space in the
receive descriptor for the hardware-provided packet checksum and the RSS
hash, respectively. Users currently must disable jumbos when receive
hashing offload is enabled, or vice versa, because of this incompatibility.
Since testing has shown that IP payload checksum does not provide any real
benefit, just remove it so that there is no longer a choice between jumbos
or receive hashing offload but not both as done in other Intel GbE drivers
(e.g. e1000, igb).
Also, add a missing check for IP checksum error reported by the hardware;
let the stack verify the checksum when this happens.
CC: stable <stable@vger.kernel.org> [3.4] Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Neil Horman [Sat, 30 Jun 2012 03:04:26 +0000 (03:04 +0000)]
sctp: be more restrictive in transport selection on bundled sacks
It was noticed recently that when we send data on a transport, its possible that
we might bundle a sack that arrived on a different transport. While this isn't
a major problem, it does go against the SHOULD requirement in section 6.4 of RFC
2960:
An endpoint SHOULD transmit reply chunks (e.g., SACK, HEARTBEAT ACK,
etc.) to the same destination transport address from which it
received the DATA or control chunk to which it is replying. This
rule should also be followed if the endpoint is bundling DATA chunks
together with the reply chunk.
This patch seeks to correct that. It restricts the bundling of sack operations
to only those transports which have moved the ctsn of the association forward
since the last sack. By doing this we guarantee that we only bundle outbound
saks on a transport that has received a chunk since the last sack. This brings
us into stricter compliance with the RFC.
Vlad had initially suggested that we strictly allow only sack bundling on the
transport that last moved the ctsn forward. While this makes sense, I was
concerned that doing so prevented us from bundling in the case where we had
received chunks that moved the ctsn on multiple transports. In those cases, the
RFC allows us to select any of the transports having received chunks to bundle
the sack on. so I've modified the approach to allow for that, by adding a state
variable to each transport that tracks weather it has moved the ctsn since the
last sack. This I think keeps our behavior (and performance), close enough to
our current profile that I think we can do this without a sysctl knob to
enable/disable it.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com> CC: Vlad Yaseivch <vyasevich@gmail.com> CC: David S. Miller <davem@davemloft.net> CC: linux-sctp@vger.kernel.org Reported-by: Michele Baldessari <michele@redhat.com> Reported-by: sorin serban <sserban@redhat.com> Acked-by: Vlad Yasevich <vyasevich@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Mitch A Williams [Sat, 30 Jun 2012 00:23:19 +0000 (00:23 +0000)]
igbvf: fix divide by zero
Using ethtool -C ethX rx-usecs 0 crashes with a divide by zero.
Refactor this function to fix this issue and make it more clear
what the intent of each conditional is. Add comment regarding
using a setting of zero.
CC: stable <stable@vger.kernel.org> [3.3+] CC: David Ahern <daahern@cisco.com> Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 30 Jun 2012 23:01:50 +0000 (16:01 -0700)]
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Another week, another batch of fixes.
All are small, contained, targeted fixes for explicit problems --
mostly build and boot failures across i.MX, OMAP, Renesas/Shmobile and
Samsung."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: imx6q: fix suspend regression caused by common clk migration
ARM: OMAP4470: Fix OMAP4470 boot failure
ARM: EXYNOS: Fix EXYNOS_DEV_DMA Kconfig entry
ARM: OMAP2+: nand: fix build error when CONFIG_MTD_ONENAND_OMAP2=n
ARM: shmobile: r8a7779: Route all interrupts to ARM
ARM: shmobile: kzm9d: use late init machine hook
ARM: shmobile: kzm9g: use late init machine hook
ARM: mach-shmobile: armadillo800eva: Use late init machine hook
ARM: SAMSUNG: Fix for S3C2412 EBI memory mapping
ARM: mach-shmobile: add missing GPIO IRQ configuration on mackerel
ARM: mach-shmobile: Fix build when SMP is enabled and EMEV2 is not enabled
ARM: shmobile: sh7372: bugfix: chclr_offset base
ARM: shmobile: sh73a0: bugfix: SY-DMAC number
ARM: SAMSUNG: Should check for IS_ERR(clk) instead of NULL
Randy Dunlap [Sat, 30 Jun 2012 22:37:24 +0000 (15:37 -0700)]
printk.c: fix kernel-doc warnings
Fix kernel-doc warnings in printk.c: use correct parameter name.
Warning(kernel/printk.c:2429): No description found for parameter 'buf'
Warning(kernel/printk.c:2429): Excess function parameter 'line' description in 'kmsg_dump_get_buffer'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Randy Dunlap [Sat, 30 Jun 2012 22:30:46 +0000 (15:30 -0700)]
linux/irq.h: fix kernel-doc warning
Fix kernel-doc warning. This struct member was removed in commit 875682648b89 ("irq: Remove irq_chip->release()") so remove its
associated kernel-doc entry also.
Warning(include/linux/irq.h:338): Excess struct/union/enum/typedef member 'release' description in 'irq_chip'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net> Cc: Richard Weinberger <richard@nod.at> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Shawn Guo [Tue, 5 Jun 2012 07:16:43 +0000 (15:16 +0800)]
ARM: imx6q: fix suspend regression caused by common clk migration
When moving to common clk framework, the imx6q clks rom and mmdc_ch1_axi
get different on/off states than old clk driver, which breaks suspend
function. There might be a better way to manage these clocks, but let's
takes the old clk driver approach to fix the regression first.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Olof Johansson <olof@lixom.net>
Linus Torvalds [Sat, 30 Jun 2012 18:11:58 +0000 (11:11 -0700)]
Merge branch 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux
Pull ACPI & Power Management patches from Len Brown.
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
acpi_pad: fix power_saving thread deadlock
ACPI video: Still use ACPI backlight control if _DOS doesn't exist
ACPI, APEI, Avoid too much error reporting in runtime
ACPI: Add a quirk for "AMILO PRO V2030" to ignore the timer overriding
ACPI: Remove one board specific WARN when ignoring timer overriding
ACPI: Make acpi_skip_timer_override cover all source_irq==0 cases
ACPI, x86: fix Dell M6600 ACPI reboot regression via DMI
ACPI sysfs.c strlen fix
Linus Torvalds [Sat, 30 Jun 2012 17:11:24 +0000 (10:11 -0700)]
Merge tag 'driver-core-3.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver Core fixes from Greg Kroah-Hartman:
"Here is a number of printk() fixes, specifically a few reported by the
crazy blog program that ships in SUSE releases (that's "boot log" and
not "web log", it predates the general "blog" terminology by many
years), and the restoration of the continuation line functionality
reported by Stephen and others. Yes, the changes seem a bit big this
late in the cycle, but I've been beating on them for a while now, and
Stephen has even optimized it a bit, so all looks good to me.
The other change in here is a Documentation update for the stable
kernel rules describing how some distro patches should be backported,
to hopefully drive a bit more response from the distros to the stable
kernel releases.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'driver-core-3.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
printk: Optimize if statement logic where newline exists
printk: flush continuation lines immediately to console
syslog: fill buffer with more than a single message for SYSLOG_ACTION_READ
Revert "printk: return -EINVAL if the message len is bigger than the buf size"
printk: fix regression in SYSLOG_ACTION_CLEAR
stable: Allow merging of backports for serious user-visible performance issues
Stuart Hayes [Wed, 13 Jun 2012 21:10:45 +0000 (16:10 -0500)]
acpi_pad: fix power_saving thread deadlock
The acpi_pad driver can get stuck in destroy_power_saving_task()
waiting for kthread_stop() to stop a power_saving thread. The problem
is that the isolated_cpus_lock mutex is owned when
destroy_power_saving_task() calls kthread_stop(), which waits for a
power_saving thread to end, and the power_saving thread tries to
acquire the isolated_cpus_lock when it calls round_robin_cpu(). This
patch fixes the issue by making round_robin_cpu() use its own mutex.
https://bugzilla.kernel.org/show_bug.cgi?id=42981
Cc: stable@vger.kernel.org Signed-off-by: Stuart Hayes <Stuart_Hayes@Dell.com> Signed-off-by: Len Brown <len.brown@intel.com>
Some platforms don't have _DOS control method, but the ACPI
backlight still works.
We should not invoke _DOS for these platforms.
https://bugzilla.kernel.org/show_bug.cgi?id=43168
Cc: Igor Murzov <intergalactic.anonymous@gmail.com> Cc: stable@vger.kernel.org Signed-off-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
Linus Torvalds [Sat, 30 Jun 2012 02:05:41 +0000 (19:05 -0700)]
Merge tag 'pm-for-3.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael J. Wysocki:
* Fix for a bug in async suspend error code path causing parents to
wait forever for their children in case of a suspend error from
Mandeep Singh Baines (-stable metarial).
* Fix for a suspend regression related to earlier changes in the ACPI
cpuidle driver from Deepthi Dharwar.
* tag 'pm-for-3.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / ACPI: Fix suspend/resume regression caused by cpuidle cleanup.
PM / Sleep: Prevent waiting forever on asynchronous suspend after abort
Steven Rostedt [Fri, 29 Jun 2012 15:40:11 +0000 (11:40 -0400)]
printk: Optimize if statement logic where newline exists
In reviewing Kay's fix up patch: "printk: Have printk() never buffer its
data", I found two if statements that could be combined and optimized.
Put together the two 'cont.len && cont.owner == current' if statements
into a single one, and check if we need to call cont_add(). This also
removes the unneeded double cont_flush() calls.
Linus Torvalds [Fri, 29 Jun 2012 20:50:11 +0000 (13:50 -0700)]
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull powerpc fixes from Benjamin Herrenschmidt:
"Here are a few powerpc fixes. Arguably some of this should have come
to you earlier but I'm only just catching up after my medical leave.
Mostly these fixes regressions, a couple are long standing bugs."
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/pseries: Fix software invalidate TCE
powerpc: check_and_cede_processor() never cedes
powerpc/ftrace: Do not trace restore_interrupts()
powerpc: Fix Section mismatch warnings in prom_init.c
ppc64: fix missing to check all bits of _TIF_USER_WORK_MASK in preempt
powerpc: Fix uninitialised error in numa.c
powerpc: Fix BPF_JIT code to link with multiple TOCs
Linus Torvalds [Fri, 29 Jun 2012 17:29:21 +0000 (10:29 -0700)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull oprofile fixlet from Ingo Molnar.
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
oprofile: perf: use NR_CPUS instead or nr_cpumask_bits for static array
Kay Sievers [Thu, 28 Jun 2012 07:38:53 +0000 (09:38 +0200)]
printk: flush continuation lines immediately to console
Continuation lines are buffered internally, intended to merge the
chunked printk()s into a single record, and to isolate potentially
racy continuation users from usual terminated line users.
This though, has the effect that partial lines are not printed to
the console in the moment they are emitted. In case the kernel
crashes in the meantime, the potentially interesting printed
information would never reach the consoles.
Here we share the continuation buffer with the console copy logic,
and partial lines are always immediately flushed to the available
consoles. They are still buffered internally to improve the
readability and integrity of the messages and minimize the amount
of needed record headers to store.
Signed-off-by: Kay Sievers <kay@vrfy.org> Tested-by: Steven Rostedt <rostedt@goodmis.org> Acked-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alex Deucher [Thu, 28 Jun 2012 21:53:07 +0000 (17:53 -0400)]
drm/radeon: fix VM page table setup on SI
Cayman and trinity allow for variable sized VM page
tables, but SI requires that all page tables be the
same size. The current code assumes variablely sized
VM page tables so SI may end up with part of each page
table overlapping with other memory which could end
up being interpreted by the VM hw as garbage.
Change the code to better accomodate SI. Allocate enough
space for at least 2 full page tables and always set
last_pfn to max_pfn on SI so each VM is backed by a full
page table. This limits us to only 2 VMs active at any
given time on SI. This will be rectified and the code can
be reunified once we move to two level page tables.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Jerome Glisse <jglisse@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Dave Airlie <airlied@redhat.com>
Tomasz Bursztyka [Thu, 28 Jun 2012 02:57:49 +0000 (02:57 +0000)]
netfilter: nfnetlink: fix missing rcu_read_unlock in nfnetlink_rcv_msg
Bug added in commit 6b75e3e8d664a9a (netfilter: nfnetlink: add RCU in
nfnetlink_rcv_msg())
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Kailang Yang [Fri, 29 Jun 2012 07:35:52 +0000 (09:35 +0200)]
ALSA: hda - Fix no sound from ALC662 after Windows reboot
Windows use hidden register to control EAPD.
Linux use verb to control EAPD.
If windows reboot to Linux, it must change the EAPD control to verb
control.
Signed-off-by: Kailang Yang <kailang@realtek.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Hebbar, Gururaja [Tue, 26 Jun 2012 13:55:11 +0000 (19:25 +0530)]
ASoC: tlv320aic3x: Fix codec pll configure bug
In sound/soc/codecs/tlv320aic3x.c
data = snd_soc_read(codec, AIC3X_PLL_PROGA_REG);
snd_soc_write(codec, AIC3X_PLL_PROGA_REG,
data | (pll_p << PLLP_SHIFT));
In the above code, pll-p value is OR'ed with previous value without
clearing it. Bug is not seen if pll-p value doesn't change across
Sampling frequency.
However on some platforms (like AM335x EVM-SK), pll-p may have different
values across different sampling frequencies. In such case, above code
configures the pll with a wrong value.
Because of this bug, when a audio stream is played with pll value
different from previous stream, audio is heard as differently(like its
stretched).
Signed-off-by: Hebbar, Gururaja <gururaja.hebbar@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: stable@vger.kernel.org
Anton Blanchard [Wed, 27 Jun 2012 13:13:52 +0000 (13:13 +0000)]
powerpc: check_and_cede_processor() never cedes
Commit f948501b36c6 ("Make hard_irq_disable() actually hard-disable
interrupts") caused check_and_cede_processor to stop working.
->irq_happened will never be zero right after a hard_irq_disable
so the compiler removes the call to cede_processor completely.
The bug was introduced back in the lazy interrupt handling rework
of 3.4 but was hidden until recently because hard_irq_disable did
nothing.
This issue will eventually appear in 3.4 stable since the
hard_irq_disable fix is marked stable, so mark this one for stable
too.
Signed-off-by: Anton Blanchard <anton@samba.org> Cc: stable@vger.kernel.org Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Steven Rostedt [Mon, 4 Jun 2012 16:27:54 +0000 (16:27 +0000)]
powerpc/ftrace: Do not trace restore_interrupts()
As I was adding code that affects all archs, I started testing function
tracer against PPC64 and found that it currently locks up with 3.4
kernel. I figured it was due to tracing a function that shouldn't be, so
I went through the following process to bisect to find the culprit:
cat /debug/tracing/available_filter_functions > t
num=`wc -l t`
sed -ne "1,${num}p" t > t1
let num=num+1
sed -ne "${num},$p" t > t2
cat t1 > /debug/tracing/set_ftrace_filter
echo function /debug/tracing/current_tracer
<failed? bisect t1, if not bisect t2>
It finally came down to this function: restore_interrupts()
I'm not sure why this locks up the system. It just seems to prevent
scheduling from occurring. Interrupts seem to still work, as I can ping
the box. But all user processes freeze.
When restore_interrupts() is not traced, function tracing works fine.
Cc: stable@kernel.org Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Li Zhong [Thu, 7 Jun 2012 17:44:23 +0000 (17:44 +0000)]
powerpc: Fix Section mismatch warnings in prom_init.c
This patches tries to fix a couple of Section mismatch warnings like
following one:
WARNING: arch/powerpc/kernel/built-in.o(.text+0x2923c): Section mismatch
in reference from the function .prom_query_opal() to the
function .init.text:.call_prom()
The function .prom_query_opal() references
the function __init .call_prom().
This is often because .prom_query_opal lacks a __init
annotation or the annotation of .call_prom is wrong.
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tiejun Chen [Wed, 6 Jun 2012 20:56:43 +0000 (20:56 +0000)]
ppc64: fix missing to check all bits of _TIF_USER_WORK_MASK in preempt
In entry_64.S version of ret_from_except_lite, you'll notice that
in the !preempt case, after we've checked MSR_PR we test for any
TIF flag in _TIF_USER_WORK_MASK to decide whether to go to do_work
or not. However, in the preempt case, we do a convoluted trick to
test SIGPENDING only if PR was set and always test NEED_RESCHED ...
but we forget to test any other bit of _TIF_USER_WORK_MASK !!! So
that means that with preempt, we completely fail to test for things
like single step, syscall tracing, etc...
This should be fixed as the following path:
- Test PR. If not set, go to resume_kernel, else continue.
- If go resume_kernel, to do that original do_work.
- If else, then always test for _TIF_USER_WORK_MASK to decide to do
that original user_work, else restore directly.
Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Neuling [Tue, 19 Jun 2012 20:01:45 +0000 (20:01 +0000)]
powerpc: Fix uninitialised error in numa.c
chroma_defconfig currently gives me this with gcc 4.6:
arch/powerpc/mm/numa.c:638:13: error: 'dm' may be used uninitialized in this function [-Werror=uninitialized]
It's a bogus warning/error since of_get_drconf_memory() only writes it
anyway.
Signed-off-by: Michael Neuling <mikey@neuling.org>
cc: <stable@kernel.org> [v3.3+] Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Ellerman [Thu, 21 Jun 2012 17:50:27 +0000 (17:50 +0000)]
powerpc: Fix BPF_JIT code to link with multiple TOCs
If the kernel is big enough (eg. allyesconfig), the linker may need to
switch TOCs when calling from the BPF JIT code out to the external
helpers (skb_copy_bits() & bpf_internal_load_pointer_neg_helper()).
In order to do that we need to leave space after the bl for the linker
to insert a reload of our TOC pointer.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Acked-by: Matt Evans <matt@ozlabs.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Daniel Mack [Thu, 28 Jun 2012 06:12:32 +0000 (06:12 +0000)]
davinci_cpdma: include linux/module.h
This fixes a number of warnings such as:
CC drivers/net/ethernet/ti/davinci_cpdma.o
drivers/net/ethernet/ti/davinci_cpdma.c:279:1: warning: data definition
has no type or storage class
drivers/net/ethernet/ti/davinci_cpdma.c:279:1: warning: type defaults to
‘int’ in declaration of ‘EXPORT_SYMBOL_GPL’
drivers/net/ethernet/ti/davinci_cpdma.c:279:1: warning: parameter names
(without types) in function declaration
Signed-off-by: Daniel Mack <zonque@gmail.com> Cc: Vaibhav Hiremath <hvaibhav@ti.com> Cc: David S. Miller <davem@davemloft.net> Cc: Christian Riesch <christian.riesch@omicron.at> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 28 Jun 2012 23:58:09 +0000 (16:58 -0700)]
Merge branch 'for-davem' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
John Linville says:
====================
Amitkumar Karwar gives us two mwifiex fixes: one fixes some skb
manipulations when handling some event messages; and another that
does some similar fixing on an error path.
Avinash Patil gives us a fix for for a memory leak in mwifiex.
Dan Rosenberg offers an NFC NCI fix to enforce some message length
limits to prevent buffer overflows.
Eliad Peller provides a mac80211 fix to prevent some frames from
being built with an invalid BSSID.
Eric Dumazet sends an NFC fix to prevent a BUG caused by a NULL
pointer dereference.
Felix Fietkau has an ath9k fix for a regression causing
LEAP-authenticated connection failures.
Johannes Berg provides an iwlwifi fix that eliminates some log SPAM
after an authentication/association timeout. He also provides a
mac80211 fix to prevent incorrectly addressing certain action frames
(and in so doing, to comply with the 802.11 specs).
Larry Finger provides a few USB IDs for the rtl8192cu driver --
should be harmless.
Panayiotis Karabassis provices a one-liner to fix kernel bug 42903
(a system freeze).
Randy Dunlap provides a one-line Kconfig change to prevent build
failures with some configurations.
Stone Piao provides an mwifiex sequence numbering fix and a fix
to prevent mwifiex from attempting to include eapol frames in an
aggregation frame.
Finally, Tom Hughes provides an ath9k fix for a NULL pointer
dereference.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Claudiu Manoil [Thu, 28 Jun 2012 04:40:53 +0000 (04:40 +0000)]
gianfar: Fix RXICr/TXICr programming for multi-queue mode
The correct behavior is to program the interrupt coalescing regs
(RXICr/TXICr) in accordance with the Rx/Tx Q's "rx/txcoalescing"
flag. That is, if the coalescing flag is 0 for a given Rx/Tx queue
then the corresponding coalescing register should be cleared.
This behavior is correctly implemented for the single-queue mode
(SQ_SG_MODE), but not for the multi-queue mode (MQ_MG_MODE).
This fixes the later case.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bjørn Mork [Thu, 21 Jun 2012 23:11:18 +0000 (23:11 +0000)]
net: qmi_wwan: fix Oops while disconnecting
usbnet_disconnect() will set intfdata to NULL before calling
the minidriver unbind function. The cdc_wdm subdriver cannot
know that it is disconnecting until the qmi_wwan unbind
function has called its disconnect function. This means that
we must be able to support the cdc_wdm subdriver operating
normally while usbnet_disconnect() is running, and in
particular that intfdata may be NULL.
The only place this matters is in qmi_wwan_cdc_wdm_manage_power
which is called from cdc_wdm. Simply testing for NULL
intfdata there is sufficient to allow it to continue working
at all times.
Fixes this Oops where a cdc-wdm device was closed while the
USB device was disconnecting, causing wdm_release to call
qmi_wwan_cdc_wdm_manage_power after intfdata was set to
NULL by usbnet_disconnect:
Reported-by: Marius Bjørnstad Kotsbak <marius.kotsbak@gmail.com> Cc: <stable@vger.kernel.org> # v3.4 Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 28 Jun 2012 19:38:51 +0000 (12:38 -0700)]
Merge tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon changes from Guenter Roeck:
"Just e-mail address updates"
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: Update my e-mail address
hwmon: (applesmc) correct email address for Jesper Juhl
Linus Torvalds [Thu, 28 Jun 2012 18:51:19 +0000 (11:51 -0700)]
Merge git://www.linux-watchdog.org/linux-watchdog
Pull watchdog fixes from Wim Van Sebroeck:
"This fixes:
- the WDIOC_GETSTATUS return value
- the unregister of all NMI events on exit
- the loading of the iTCO_wdt driver after the conversion to the
lpc_ich mfd model."
* git://www.linux-watchdog.org/linux-watchdog:
watchdog: core: fix WDIOC_GETSTATUS return value
watchdog: hpwdt: Unregister NMI events on exit.
watchdog: iTCO_wdt: add platform driver module alias
Linus Torvalds [Thu, 28 Jun 2012 18:43:45 +0000 (11:43 -0700)]
Merge branch 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs
Pull UDF fixes from Jan Kara:
"Make UDF more robust in presence of corrupted filesystem"
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
udf: Fortify loading of sparing table
udf: Avoid run away loop when partition table length is corrupted
udf: Use 'ret' instead of abusing 'i' in udf_load_logicalvol()
Linus Torvalds [Thu, 28 Jun 2012 18:41:43 +0000 (11:41 -0700)]
Merge tag 'upstream-3.5-rc5' of git://git.infradead.org/linux-ubifs
Pull ubi/ubifs fixes from Artem Bityutskiy:
"Fix the debugfs regression - we never enable it because incorrect
'IS_ENABLED()' macro usage: should be 'IS_ENABLED(CONFIG_DEBUG_FS)',
but we had 'IS_ENABLED(DEBUG_FS)'. Also fix incorrect assertion."
* tag 'upstream-3.5-rc5' of git://git.infradead.org/linux-ubifs:
UBI: correct usage of IS_ENABLED()
UBIFS: correct usage of IS_ENABLED()
UBIFS: fix assertion
Wim Van Sebroeck [Tue, 26 Jun 2012 18:07:21 +0000 (20:07 +0200)]
watchdog: core: fix WDIOC_GETSTATUS return value
In commit 7a87982420e5e126bfefeb42232d1fd92052794e we added
a wrapper for the WDIOC_GETSTATUS ioctl call. The code results
however in a different behaviour: it returns an error if the
driver doesn't support the status operation. This is not
according to the API that says that when we don't support
the status operation, that we just should return a 0 value.
Only when the device isn't there anymore, we should return an
error.
Jan Beulich [Fri, 22 Jun 2012 15:41:00 +0000 (16:41 +0100)]
watchdog: iTCO_wdt: add platform driver module alias
The recent conversion of iTCO_wdt resulted in the driver no longer
getting loaded automatically, since it no longer has a
MODULE_DEVICE_TABLE() included. As the lpc_ich driver now creates a
platform device, auto-loading can easily be done by having a respective
module alias in place.
Signed-off-by: Jan Beulich <jbeulich@suse.com> Cc: Aaron Sierra <asierra@xes-inc.com> Acked-by: Guenter Roeck <linux@roeck-us.net> Cc: Samuel Ortiz <sameo@linux.intel.com> Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Linus Torvalds [Thu, 28 Jun 2012 18:26:42 +0000 (11:26 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Nearly all intel, one missing license header in nouveau, nothing
majorly earth shattering."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
Revert "drm/i915: allow PCH PWM override on IVB"
drm/nouveau: add license header to prime.
drm/i915: Fix eDP blank screen after S3 resume on HP desktops
drm/i915: rip out the PM_IIR WARN
projects / mirror_ubuntu-eoan-kernel.git / log