Before this patch, the symbol end address fixup to be called, needed two
conditions being met:
if (prev->end == prev->start && prev->end != curr->start)
Where
"prev->end == prev->start" means that prev is zero-long
(and thus needs a fixup)
and
"prev->end != curr->start" means that fixup hasn't been applied yet
However, this logic is incorrect in the following situation:
In this case, prev->start == prev->end == curr->start == curr->end,
thus the condition above thinks that "we need a fixup due to zero
length of prev symbol, but it has been probably done, since the
prev->end == curr->start", which is wrong.
After the patch, the execution path proceeds to arch__symbols__fixup_end
function which fixes up the size of prev symbol by adding page_size to
its end offset.
Fixes: 3b01a413c196c910 ("perf symbols: Improve kallsyms symbol end addr calculation") Signed-off-by: Michael Petlan <mpetlan@redhat.com> Cc: Athira Jajeev <atrajeev@linux.vnet.ibm.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Kajol Jain <kjain@linux.ibm.com> Cc: Madhavan Srinivasan <maddy@linux.ibm.com> Link: http://lore.kernel.org/lkml/20220317135536.805-1-mpetlan@redhat.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Syzbot reported warning in usb_submit_urb() which is caused by wrong
endpoint type. There was a check for the number of endpoints, but not
for the type of endpoint.
Fix it by replacing old desc.bNumEndpoints check with
usb_find_common_endpoints() helper for finding endpoints
Fail log:
usb 5-1: BOGUS urb xfer, pipe 1 != type 3
WARNING: CPU: 2 PID: 48 at drivers/usb/core/urb.c:502 usb_submit_urb+0xed2/0x18a0 drivers/usb/core/urb.c:502
Modules linked in:
CPU: 2 PID: 48 Comm: kworker/2:2 Not tainted 5.17.0-rc6-syzkaller-00226-g07ebd38a0da2 #0
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.14.0-2 04/01/2014
Workqueue: usb_hub_wq hub_event
...
Call Trace:
<TASK>
aiptek_open+0xd5/0x130 drivers/input/tablet/aiptek.c:830
input_open_device+0x1bb/0x320 drivers/input/input.c:629
kbd_connect+0xfe/0x160 drivers/tty/vt/keyboard.c:1593
Fixes: 8e20cf2bce12 ("Input: aiptek - fix crash on detecting device without endpoints") Reported-and-tested-by: syzbot+75cccf2b7da87fb6f84b@syzkaller.appspotmail.com Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Link: https://lore.kernel.org/r/20220308194328.26220-1-paskripkin@gmail.com Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Although the bug manifested in the driver core, the real cause was a
race with the gadget core. dev_uevent() does:
if (dev->driver)
add_uevent_var(env, "DRIVER=%s", dev->driver->name);
and between the test and the dereference of dev->driver, the gadget
core sets dev->driver to NULL.
The race wouldn't occur if the gadget core registered its devices on
a real bus, using the standard synchronization techniques of the
driver core. However, it's not necessary to make such a large change
in order to fix this bug; all we need to do is make sure that
udc->dev.driver is always NULL.
In fact, there is no reason for udc->dev.driver ever to be set to
anything, let alone to the value it currently gets: the address of the
gadget's driver. After all, a gadget driver only knows how to manage
a gadget, not how to manage a UDC.
This patch simply removes the statements in the gadget core that touch
udc->dev.driver.
Fixes: 2ccea03a8f7e ("usb: gadget: introduce UDC Class") CC: <stable@vger.kernel.org> Reported-and-tested-by: syzbot+348b571beb5eeb70a582@syzkaller.appspotmail.com Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/YiQgukfFFbBnwJ/9@rowland.harvard.edu Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The newly introduced TRAMP_VALIAS definition causes a build warning
with clang-14:
arch/arm64/include/asm/vectors.h:66:31: error: arithmetic on a null pointer treated as a cast from integer to pointer is a GNU extension [-Werror,-Wnull-pointer-arithmetic]
return (char *)TRAMP_VALIAS + SZ_2K * slot;
Change the addition to something clang does not complain about.
Fixes: bd09128d16fa ("arm64: Add percpu vectors for EL1") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: James Morse <james.morse@arm.com> Link: https://lore.kernel.org/r/20220316183833.1563139-1-arnd@kernel.org Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The device_node pointer is returned by of_parse_phandle() with refcount
incremented. We should use of_node_put() on it when done.
Fixes: 6d4e5c570c2d ("net: dsa: get port type at parse time") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Link: https://lore.kernel.org/r/20220316082602.10785-1-linmq006@gmail.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
As the potential failure of the kvmalloc_array(),
it should be better to check and restore the 'data'
if fails in order to avoid the dereference of the
NULL pointer.
Fixes: 6ae746711263 ("hv_netvsc: Add per-cpu ethtool stats for netvsc") Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn> Link: https://lore.kernel.org/r/20220314020125.2365084-1-jiasheng@iscas.ac.cn Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
As the potential failure of the dma_map_single(),
it should be better to check it and return error
if fails.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
syzbot found that when an AF_PACKET socket is using PACKET_COPY_THRESH
and mmap operations, tpacket_rcv() is queueing skbs with
garbage in skb->cb[], triggering a too big copy [1]
Presumably, users of af_packet using mmap() already gets correct
metadata from the mapped buffer, we can simply make sure
to clear 12 bytes that might be copied to user space later.
BUG: KASAN: stack-out-of-bounds in memcpy include/linux/fortify-string.h:225 [inline]
BUG: KASAN: stack-out-of-bounds in packet_recvmsg+0x56c/0x1150 net/packet/af_packet.c:3489
Write of size 165 at addr ffffc9000385fb78 by task syz-executor233/3631
This bug resulted in only the current mode being resumed and suspended when
the PHY supported both fiber and copper modes and when the PHY only supported
copper mode the fiber mode would incorrectly be attempted to be resumed and
suspended.
Fixes: 3758be3dc162 ("Marvell phy: add functions to suspend and resume both interfaces: fiber and copper links.") Signed-off-by: Kurt Cancemi <kurt@x64architecture.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20220312201512.326047-1-kurt@x64architecture.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When "dump_apple_properties" is used on the kernel boot command line,
it causes an Unknown parameter message and the string is added to init's
argument strings:
Unknown kernel command line parameters "dump_apple_properties
BOOT_IMAGE=/boot/bzImage-517rc6 efivar_ssdt=newcpu_ssdt", will be
passed to user space.
Run /sbin/init as init process
with arguments:
/sbin/init
dump_apple_properties
with environment:
HOME=/
TERM=linux
BOOT_IMAGE=/boot/bzImage-517rc6
efivar_ssdt=newcpu_ssdt
Similarly when "efivar_ssdt=somestring" is used, it is added to the
Unknown parameter message and to init's environment strings, polluting
them (see examples above).
Change the return value of the __setup functions to 1 to indicate
that the __setup options have been handled.
Fixes: 58c5475aba67 ("x86/efi: Retrieve and assign Apple device properties") Fixes: 475fb4e8b2f4 ("efi / ACPI: load SSTDs from EFI variables") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Reported-by: Igor Zhbanov <i.zhbanov@omprussia.ru>
Link: lore.kernel.org/r/64644a2f-4a20-bab3-1e15-3b2cdd0defe3@omprussia.ru Cc: Ard Biesheuvel <ardb@kernel.org> Cc: linux-efi@vger.kernel.org Cc: Lukas Wunner <lukas@wunner.de> Cc: Octavian Purdila <octavian.purdila@intel.com> Cc: "Rafael J. Wysocki" <rafael@kernel.org> Cc: Matt Fleming <matt@codeblueprint.co.uk> Link: https://lore.kernel.org/r/20220301041851.12459-1-rdunlap@infradead.org Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Once s_root is set, genric_shutdown_super() will be called if
fill_super() fails. That means, we will call ocfs2_dismount_volume()
twice in such case, which can lead to kernel crash.
Fix this issue by initializing filecheck kobj before setting s_root.
Link: https://lkml.kernel.org/r/20220310081930.86305-1-joseph.qi@linux.alibaba.com Fixes: 5f483c4abb50 ("ocfs2: add kobject for online file check") Signed-off-by: Joseph Qi <joseph.qi@linux.alibaba.com> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Changwei Ge <gechangwei@live.cn> Cc: Gang He <ghe@suse.com> Cc: Jun Piao <piaojun@huawei.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The generate function in struct rng_alg expects that the destination
buffer is completely filled if the function returns 0. qcom_rng_read()
can run into a situation where the buffer is partially filled with
randomness and the remaining part of the buffer is zeroed since
qcom_rng_generate() doesn't check the return value. This issue can
be reproduced by running the following from libkcapi:
The generated OUTFILE will have three huge sections that contain all
zeros, and this is caused by the code where the test
'val & PRNG_STATUS_DATA_AVAIL' fails.
Let's fix this issue by ensuring that qcom_rng_read() always returns
with a full buffer if the function returns success. Let's also have
qcom_rng_generate() return the correct value.
Here's some statistics from the ent project
(https://www.fourmilab.ch/random/) that shows information about the
quality of the generated numbers:
Optimum compression would reduce the size
of this 9000000 byte file by 2 percent.
Chi square distribution for 9000000 samples is 9329962.81, and
randomly would exceed this value less than 0.01 percent of the
times.
Arithmetic mean value of data bytes is 119.3731 (127.5 = random).
Monte Carlo value for Pi is 3.197293333 (error 1.77 percent).
Serial correlation coefficient is 0.159130 (totally uncorrelated =
0.0).
Without this patch, the results of the chi-square test is 0.01%, and
the numbers are certainly not random according to ent's project page.
The results improve with this patch:
Optimum compression would reduce the size
of this 9000000 byte file by 0 percent.
Chi square distribution for 9000000 samples is 258.77, and randomly
would exceed this value 42.24 percent of the times.
Arithmetic mean value of data bytes is 127.5006 (127.5 = random).
Monte Carlo value for Pi is 3.141277333 (error 0.01 percent).
Serial correlation coefficient is 0.000468 (totally uncorrelated =
0.0).
This change was tested on a Nexus 5 phone (msm8974 SoC).
Signed-off-by: Brian Masney <bmasney@redhat.com> Fixes: ceec5f5b5988 ("crypto: qcom-rng - Add Qcom prng driver") Cc: stable@vger.kernel.org # 4.19+ Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Reviewed-by: Andrew Halaney <ahalaney@redhat.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
James Morse [Fri, 18 Mar 2022 17:37:13 +0000 (17:37 +0000)]
fixup for "arm64 entry: Add macro for reading symbol address from the trampoline"
BugLink: https://bugs.launchpad.net/bugs/1969678
__sdei_asm_trampoline_next_handler shouldn't have its own name as the
tramp_data_read_var takes the symbol name, and generates the name for
the value in the data page if CONFIG_RANDOMIZE_BASE is clear.
This means when CONFIG_RANDOMIZE_BASE is clear, this code won't compile
as __sdei_asm_trampoline_next_handler doesn't exist.
Use the proper name, and let the macro do its thing.
Reported-by: Florian Fainelli <f.fainelli@gmail.com> Tested-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: James Morse <james.morse@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The error message when I build vm tests on debian10 (GLIBC 2.28):
userfaultfd.c: In function `userfaultfd_pagemap_test':
userfaultfd.c:1393:37: error: `MADV_PAGEOUT' undeclared (first use
in this function); did you mean `MADV_RANDOM'?
if (madvise(area_dst, test_pgsize, MADV_PAGEOUT))
^~~~~~~~~~~~
MADV_RANDOM
This patch includes these newer definitions from UAPI linux/mman.h, is
useful to fix tests build on systems without these definitions in glibc
sys/mman.h.
Link: https://lkml.kernel.org/r/20220227055330.43087-2-zhouchengming@bytedance.com Signed-off-by: Chengming Zhou <zhouchengming@bytedance.com> Reviewed-by: Shuah Khan <skhan@linuxfoundation.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
seqno could be read as a stale value outside of the lock. The lock is
already acquired to protect the modification of seqno against a possible
race condition. Place the reading of this value also inside this locking
to protect it against a possible race condition.
Signed-off-by: Niels Dossche <dossche.niels@gmail.com> Acked-by: Martin Habets <habetsm.xilinx@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
If recv_actor() returns an incorrect value, tcp_read_sock()
might loop forever.
Instead, issue a one time warning and make sure to make progress.
Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: John Fastabend <john.fastabend@gmail.com> Acked-by: Jakub Sitnicki <jakub@cloudflare.com> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/r/20220302161723.3910001-2-eric.dumazet@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The wdev channel information is updated post channel switch only for
the station mode and not for the other modes. Due to this, the P2P client
still points to the old value though it moved to the new channel
when the channel change is induced from the P2P GO.
Update the bss channel after CSA channel switch completion for P2P client
interface as well.
Signed-off-by: Sreeramya Soratkal <quic_ssramya@quicinc.com> Link: https://lore.kernel.org/r/1646114600-31479-1-git-send-email-quic_ssramya@quicinc.com Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
VRR capable property is not attached by default to the connector
It is attached only if VRR is supported.
So if the driver tries to call drm core set prop function without
it being attached that causes NULL dereference.
Cc: Jani Nikula <jani.nikula@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: dri-devel@lists.freedesktop.org Signed-off-by: Manasi Navare <manasi.d.navare@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220225013055.9282-1-manasi.d.navare@intel.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Some APs misbehave when TWT is used and cause our firmware to crash.
We don't know a reasonable way to detect and work around this problem
in the FW yet. To prevent these crashes, disable TWT in the driver by
stopping to advertise TWT support.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215523 Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
[reworded the commit message] Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/20220301072926.153969-1-luca@coelho.fi Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The function ioremap() in fs_init() can fail, so its return value should
be checked.
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn> Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Register the CAN device only when all the necessary initialization is
completed. This patch makes sure all the data structures and locks are
initialized before registering the CAN device.
Link: https://lore.kernel.org/all/20220221225935.12300-1-prabhakar.mahadev-lad.rj@bp.renesas.com Reported-by: Pavel Machek <pavel@denx.de> Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> Reviewed-by: Pavel Machek <pavel@denx.de> Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
...for each but CPU 0/boot.
Basic debug printks right before the mentioned line say:
[ 0.048170] CPU: 1, smt_mask:
So smt_mask, which is sibling mask obviously, is empty when entering
the function.
This is critical, as sched_core_cpu_starting() calculates
core-scheduling parameters only once per CPU start, and it's crucial
to have all the parameters filled in at that moment (at least it
uses cpu_smt_mask() which in fact is `&cpu_sibling_map[cpu]` on
MIPS).
A bit of debugging led me to that set_cpu_sibling_map() performing
the actual map calculation, was being invocated after
notify_cpu_start(), and exactly the latter function starts CPU HP
callback round (sched_core_cpu_starting() is basically a CPU HP
callback).
While the flow is same on ARM64 (maps after the notifier, although
before calling set_cpu_online()), x86 started calculating sibling
maps earlier than starting the CPU HP callbacks in Linux 4.14 (see
[0] for the reference). Neither me nor my brief tests couldn't find
any potential caveats in calculating the maps right after performing
delay calibration, but the WARN splat is now gone.
The very same debug prints now yield exactly what I expected from
them:
Signed-off-by: Alexander Lobakin <alobakin@pm.me> Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
If an MFP station isn't authorized, the receiver will (or
at least should) drop the action frame since it's a robust
management frame, but if we're not authorized we haven't
installed keys yet. Refuse attempts to start a session as
they'd just time out.
There are signal integrity issues running the eMMC at 200MHz on Puma
RK3399-Q7.
Similar to the work-around found for RK3399 Gru boards, lowering the
frequency to 100MHz made the eMMC much more stable, so let's lower the
frequency to 100MHz.
It might be possible to run at 150MHz as on RK3399 Gru boards but only
100MHz was extensively tested.
Cc: Quentin Schulz <foss+kernel@0leil.net> Signed-off-by: Jakob Unterwurzacher <jakob.unterwurzacher@theobroma-systems.com> Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com> Link: https://lore.kernel.org/r/20220119134948.1444965-1-quentin.schulz@theobroma-systems.com Signed-off-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
xfrm_migrate cannot handle address family change of an xfrm_state.
The symptons are the xfrm_state will be migrated to a wrong address,
and sending as well as receiving packets wil be broken.
This commit fixes it by breaking the original xfrm_state_clone
method into two steps so as to update the props.family before
running xfrm_init_state. As the result, xfrm_state's inner mode,
outer mode, type and IP header length in xfrm_state_migrate can
be updated with the new address family.
Tested with additions to Android's kernel unit test suite:
https://android-review.googlesource.com/c/kernel/tests/+/1885354
Signed-off-by: Yan Yan <evitayan@google.com> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
This patch enables distinguishing SAs and SPs based on if_id during
the xfrm_migrate flow. This ensures support for xfrm interfaces
throughout the SA/SP lifecycle.
When there are multiple existing SPs with the same direction,
the same xfrm_selector and different endpoint addresses,
xfrm_migrate might fail with ENODATA.
Specifically, the code path for performing xfrm_migrate is:
Stage 1: find policy to migrate with
xfrm_migrate_policy_find(sel, dir, type, net)
Stage 2: find and update state(s) with
xfrm_migrate_state_find(mp, net)
Stage 3: update endpoint address(es) of template(s) with
xfrm_policy_migrate(pol, m, num_migrate)
Currently "Stage 1" always returns the first xfrm_policy that
matches, and "Stage 3" looks for the xfrm_tmpl that matches the
old endpoint address. Thus if there are multiple xfrm_policy
with same selector, direction, type and net, "Stage 1" might
rertun a wrong xfrm_policy and "Stage 3" will fail with ENODATA
because it cannot find a xfrm_tmpl with the matching endpoint
address.
The fix is to allow userspace to pass an if_id and add if_id
to the matching rule in Stage 1 and Stage 2 since if_id is a
unique ID for xfrm_policy and xfrm_state. For compatibility,
if_id will only be checked if the attribute is set.
Tested with additions to Android's kernel unit test suite:
https://android-review.googlesource.com/c/kernel/tests/+/1668886
Signed-off-by: Yan Yan <evitayan@google.com> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
1. In non-shutdown_ack_sent states: in sctp_sf_do_5_1B_init() and
sctp_sf_do_5_2_2_dupinit():
chunk length check should be done before any checks that may cause
to send abort, as making packet for abort will access the init_tag
from init_hdr in sctp_ootb_pkt_new().
2. In shutdown_ack_sent state: in sctp_sf_do_9_2_reshutack():
The same checks as does in sctp_sf_do_5_2_2_dupinit() is needed
for sctp_sf_do_9_2_reshutack().
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
This reverts commit 68ac0f3810e76a853b5f7b90601a05c3048b8b54 because ID
0 was meant to be used for configuring the policy/state without
matching for a specific interface (e.g., Cilium is affected, see
https://github.com/cilium/cilium/pull/18789 and
https://github.com/cilium/cilium/pull/19019).
Signed-off-by: Kai Lueke <kailueke@linux.microsoft.com> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
In some hardware implementations, coherency between the encrypted and
unencrypted mappings of the same physical page in a VM is enforced. In
such a system, it is not required for software to flush the VM's page
from all CPU caches in the system prior to changing the value of the
C-bit for the page.
So check that bit before flushing the cache.
Signed-off-by: Krish Sadhukhan <krish.sadhukhan@oracle.com> Signed-off-by: Borislav Petkov <bp@suse.de> Acked-by: Paolo Bonzini <pbonzini@redhat.com> Link: https://lkml.kernel.org/r/20200917212038.5090-4-krish.sadhukhan@oracle.com
[ The linux-5.4.y stable branch does not have the Linux 5.7 refactoring commit eaf78265a4ab ("KVM: SVM: Move SEV code to separate file") so the
change was manually applied to sev_clflush_pages() in arch/x86/kvm/svm.c. ] Signed-off-by: Liam Merwick <liam.merwick@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
In some hardware implementations, coherency between the encrypted and
unencrypted mappings of the same physical page is enforced. In such a
system, it is not required for software to flush the page from all CPU
caches in the system prior to changing the value of the C-bit for the
page. So check that bit before flushing the cache.
[ bp: Massage commit message. ]
Suggested-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: Krish Sadhukhan <krish.sadhukhan@oracle.com> Signed-off-by: Borislav Petkov <bp@suse.de> Link: https://lkml.kernel.org/r/20200917212038.5090-3-krish.sadhukhan@oracle.com Signed-off-by: Liam Merwick <liam.merwick@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
In some hardware implementations, coherency between the encrypted and
unencrypted mappings of the same physical page is enforced. In such a system,
it is not required for software to flush the page from all CPU caches in the
system prior to changing the value of the C-bit for a page. This hardware-
enforced cache coherency is indicated by EAX[10] in CPUID leaf 0x8000001f.
[ bp: Use one of the free slots in word 3. ]
Suggested-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: Krish Sadhukhan <krish.sadhukhan@oracle.com> Signed-off-by: Borislav Petkov <bp@suse.de> Link: https://lkml.kernel.org/r/20200917212038.5090-2-krish.sadhukhan@oracle.com Signed-off-by: Liam Merwick <liam.merwick@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The in-kernel ext4 resize code doesn't support filesystem with the
sparse_super2 feature. It fails with errors like this and doesn't finish
the resize:
EXT4-fs (loop0): resizing filesystem from 16640 to 7864320 blocks
EXT4-fs warning (device loop0): verify_reserved_gdb:760: reserved GDT 2 missing grp 1 (32770)
EXT4-fs warning (device loop0): ext4_resize_fs:2111: error (-22) occurred during file system resize
EXT4-fs (loop0): resized filesystem to 2097152
The userspace resize2fs tool has a check for this case: it checks if the
filesystem has sparse_super2 set and if the kernel provides
/sys/fs/ext4/features/sparse_super2. However, the former check requires
manually reading and parsing the filesystem superblock.
Detect this case in ext4_resize_begin and error out early with a clear
error message.
When building for Thumb2, the vectors make use of a local label. Sadly,
the Spectre BHB code also uses a local label with the same number which
results in the Thumb2 reference pointing at the wrong place. Fix this
by changing the number used for the Spectre BHB local label.
Fixes: b9baf5c8c5c3 ("ARM: Spectre-BHB workaround") Tested-by: Nathan Chancellor <nathan@kernel.org> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The feature negotiation was designed in a way that
makes it possible for devices to know which config
fields will be accessed by drivers.
This is broken since commit 404123c2db79 ("virtio: allow drivers to
validate features") with fallout in at least block and net. We have a
partial work-around in commit 2f9a174f918e ("virtio: write back
F_VERSION_1 before validate") which at least lets devices find out which
format should config space have, but this is a partial fix: guests
should not access config space without acknowledging features since
otherwise we'll never be able to change the config space format.
To fix, split finalize_features from virtio_finalize_features and
call finalize_features with all feature bits before validation,
and then - if validation changed any bits - once again after.
Since virtio_finalize_features no longer writes out features
rename it to virtio_features_ok - since that is what it does:
checks that features are ok with the device.
As a side effect, this also reduces the amount of hypervisor accesses -
we now only acknowledge features once unless we are clearing any
features when validating (which is uncommon).
IRC I think that this was more or less always the intent in the spec but
unfortunately the way the spec is worded does not say this explicitly, I
plan to address this at the spec level, too.
Acked-by: Jason Wang <jasowang@redhat.com> Cc: stable@vger.kernel.org Fixes: 404123c2db79 ("virtio: allow drivers to validate features") Fixes: 2f9a174f918e ("virtio: write back F_VERSION_1 before validate") Cc: "Halil Pasic" <pasic@linux.ibm.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
virtio_finalize_features is only used internally within virtio.
No reason to export it.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Reviewed-by: Cornelia Huck <cohuck@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Legacy and old PCI I/O based cards do not support 32-bit I/O addressing.
Since commit 64f160e19e92 ("PCI: aardvark: Configure PCIe resources from
'ranges' DT property") kernel can set different PCIe address on CPU and
different on the bus for the one A37xx address mapping without any firmware
support in case the bus address does not conflict with other A37xx mapping.
So remap I/O space to the bus address 0x0 to enable support for old legacy
I/O port based cards which have hardcoded I/O ports in low address space.
Note that DDR on A37xx is mapped to bus address 0x0. And mapping of I/O
space can be set to address 0x0 too because MEM space and I/O space are
separate and so do not conflict.
Remapping IO space on Turris Mox to different address is not possible to
due bootloader bug.
Signed-off-by: Pali Rohár <pali@kernel.org> Reported-by: Arnd Bergmann <arnd@arndb.de> Fixes: 76f6386b25cc ("arm64: dts: marvell: Add Aardvark PCIe support for Armada 3700") Cc: stable@vger.kernel.org # 64f160e19e92 ("PCI: aardvark: Configure PCIe resources from 'ranges' DT property") Cc: stable@vger.kernel.org # 514ef1e62d65 ("arm64: dts: marvell: armada-37xx: Extend PCIe MEM space") Reviewed-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
RISC-V can do PC-relative jumps with a 32bit range using the following
two instructions:
auipc t0, imm20 ; t0 = PC + imm20 * 2^12
jalr ra, t0, imm12 ; ra = PC + 4, PC = t0 + imm12
Crucially both the 20bit immediate imm20 and the 12bit immediate imm12
are treated as two's-complement signed values. For this reason the
immediates are usually calculated like this:
..where offset is the signed offset from the auipc instruction. When
the 11th bit of offset is 0 the addition of 0x800 doesn't change the top
20 bits and imm12 considered positive. When the 11th bit is 1 the carry
of the addition by 0x800 means imm20 is one higher, but since imm12 is
then considered negative the two's complement representation means it
all cancels out nicely.
However, this addition by 0x800 (2^11) means an offset greater than or
equal to 2^31 - 2^11 would overflow so imm20 is considered negative and
result in a backwards jump. Similarly the lower range of offset is also
moved down by 2^11 and hence the true 32bit range is
[-2^31 - 2^11, 2^31 - 2^11)
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk> Fixes: e2c0cdfba7f6 ("RISC-V: User-facing API") Cc: stable@vger.kernel.org Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Currently meson_mmc_post_req() is called in meson_mmc_request() right
after meson_mmc_start_cmd(). This could lead to DMA unmapping before the request
is actually finished.
To fix, don't call meson_mmc_post_req() until meson_mmc_request_done().
Signed-off-by: Rong Chen <rong.chen@amlogic.com> Reviewed-by: Kevin Hilman <khilman@baylibre.com> Fixes: 79ed05e329c3 ("mmc: meson-gx: add support for descriptor chain mode") Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20220216124239.4007667-1-rong.chen@amlogic.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
There is an oddity in the way the RSR register flags propagate to the
ISR register (and the actual interrupt output) on this hardware: it
appears that RSR register bits only result in ISR being asserted if the
interrupt was actually enabled at the time, so enabling interrupts with
RSR bits already set doesn't trigger an interrupt to be raised. There
was already a partial fix for this race in the macb_poll function where
it checked for RSR bits being set and re-triggered NAPI receive.
However, there was a still a race window between checking RSR and
actually enabling interrupts, where a lost wakeup could happen. It's
necessary to check again after enabling interrupts to see if RSR was set
just prior to the interrupt being enabled, and re-trigger receive in that
case.
This issue was noticed in a point-to-point UDP request-response protocol
which periodically saw timeouts or abnormally high response times due to
received packets not being processed in a timely fashion. In many
applications, more packets arriving, including TCP retransmissions, would
cause the original packet to be processed, thus masking the issue.
Fixes: 02f7a34f34e3 ("net: macb: Re-enable RX interrupt only when RX is done") Cc: stable@vger.kernel.org Co-developed-by: Scott McNutt <scott.mcnutt@siriusxm.com> Signed-off-by: Scott McNutt <scott.mcnutt@siriusxm.com> Signed-off-by: Robert Hancock <robert.hancock@calian.com> Tested-by: Claudiu Beznea <claudiu.beznea@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
In FOPEN_DIRECT_IO mode, fuse_file_write_iter() calls
fuse_direct_write_iter(), which normally calls fuse_direct_io(), which then
imports the write buffer with fuse_get_user_pages(), which uses
iov_iter_get_pages() to grab references to userspace pages instead of
actually copying memory.
On the filesystem device side, these pages can then either be read to
userspace (via fuse_dev_read()), or splice()d over into a pipe using
fuse_dev_splice_read() as pipe buffers with &nosteal_pipe_buf_ops.
This is wrong because after fuse_dev_do_read() unlocks the FUSE request,
the userspace filesystem can mark the request as completed, causing write()
to return. At that point, the userspace filesystem should no longer have
access to the pipe buffer.
Fix by copying pages coming from the user address space to new pipe
buffers.
Reported-by: Jann Horn <jannh@google.com> Fixes: c3021629a0d8 ("fuse: support splice() reading from fuse device") Cc: <stable@vger.kernel.org> Signed-off-by: Miklos Szeredi <mszeredi@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When CONFIG_GENERIC_CPU_VULNERABILITIES is not set, references
to spectre_v2_update_state() cause a build error, so provide an
empty stub for that function when the Kconfig option is not set.
Fixes this build error:
arm-linux-gnueabi-ld: arch/arm/mm/proc-v7-bugs.o: in function `cpu_v7_bugs_init':
proc-v7-bugs.c:(.text+0x52): undefined reference to `spectre_v2_update_state'
arm-linux-gnueabi-ld: proc-v7-bugs.c:(.text+0x82): undefined reference to `spectre_v2_update_state'
Fixes: b9baf5c8c5c3 ("ARM: Spectre-BHB workaround") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Reported-by: kernel test robot <lkp@intel.com> Cc: Russell King <rmk+kernel@armlinux.org.uk> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: linux-arm-kernel@lists.infradead.org Cc: patches@armlinux.org.uk Acked-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Running the memfd script ./run_hugetlbfs_test.sh will often end in error
as follows:
memfd-hugetlb: CREATE
memfd-hugetlb: BASIC
memfd-hugetlb: SEAL-WRITE
memfd-hugetlb: SEAL-FUTURE-WRITE
memfd-hugetlb: SEAL-SHRINK
fallocate(ALLOC) failed: No space left on device
./run_hugetlbfs_test.sh: line 60: 166855 Aborted (core dumped) ./memfd_test hugetlbfs
opening: ./mnt/memfd
fuse: DONE
If no hugetlb pages have been preallocated, run_hugetlbfs_test.sh will
allocate 'just enough' pages to run the test. In the SEAL-FUTURE-WRITE
test the mfd_fail_write routine maps the file, but does not unmap. As a
result, two hugetlb pages remain reserved for the mapping. When the
fallocate call in the SEAL-SHRINK test attempts allocate all hugetlb
pages, it is short by the two reserved pages.
Fix by making sure to unmap in mfd_fail_write.
Link: https://lkml.kernel.org/r/20220219004340.56478-1-mike.kravetz@oracle.com Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com> Cc: Joel Fernandes <joel@joelfernandes.org> Cc: Shuah Khan <shuah@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
valid_lft, prefered_lft and tstamp are always accessed under the lock
"lock" in other places. Reading these without taking the lock may result
in inconsistencies regarding the calculation of the valid and preferred
variables since decisions are taken on these fields for those variables.
Signed-off-by: Niels Dossche <dossche.niels@gmail.com> Reviewed-by: David Ahern <dsahern@kernel.org> Signed-off-by: Niels Dossche <niels.dossche@ugent.be> Link: https://lore.kernel.org/r/20220223131954.6570-1-niels.dossche@ugent.be Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The reasoning in the commit was wrong - the code expected to setup the
watch even if 'hotplug-status' didn't exist. In fact, it relied on the
watch being fired the first time - to check if maybe 'hotplug-status' is
already set to 'connected'. Not registering a watch for non-existing
path (which is the case if hotplug script hasn't been executed yet),
made the backend not waiting for the hotplug script to execute. This in
turns, made the netfront think the interface is fully operational, while
in fact it was not (the vif interface on xen-netback side might not be
configured yet).
This was a workaround for 'hotplug-status' erroneously being removed.
But since that is reverted now, the workaround is not necessary either.
More discussion at
https://lore.kernel.org/xen-devel/afedd7cb-a291-e773-8b0d-4db9b291fa98@ipxe.org/T/#u
Signed-off-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com> Reviewed-by: Paul Durrant <paul@xen.org> Reviewed-by: Michael Brown <mbrown@fensystems.co.uk> Link: https://lore.kernel.org/r/20220222001817.2264967-2-marmarek@invisiblethingslab.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The 'hotplug-status' node should not be removed as long as the vif
device remains configured. Otherwise the xen-netback would wait for
re-running the network script even if it was already called (in case of
the frontent re-connecting). But also, it _should_ be removed when the
vif device is destroyed (for example when unbinding the driver) -
otherwise hotplug script would not configure the device whenever it
re-appear.
Moving removal of the 'hotplug-status' node was a workaround for nothing
calling network script after xen-netback module is reloaded. But when
vif interface is re-created (on xen-netback unbind/bind for example),
the script should be called, regardless of who does that - currently
this case is not handled by the toolstack, and requires manual
script call. Keeping hotplug-status=connected to skip the call is wrong
and leads to not configured interface.
More discussion at
https://lore.kernel.org/xen-devel/afedd7cb-a291-e773-8b0d-4db9b291fa98@ipxe.org/T/#u
Signed-off-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com> Reviewed-by: Paul Durrant <paul@xen.org> Link: https://lore.kernel.org/r/20220222001817.2264967-1-marmarek@invisiblethingslab.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
crash> net_device.state ffff89443b0c0000
state = 0x5 (__LINK_STATE_START| __LINK_STATE_NOCARRIER)
To prevent this scenario, we also make sure that the netdevice is present.
Signed-off-by: suresh kumar <suresh2514@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Some of the bcmgenet platforms don't correctly support WOL, yet
ethtool returns:
"Supports Wake-on: gsf"
which is false.
Ideally if there isn't a wol_irq, or there is something else that
keeps the device from being able to wakeup it should display:
"Supports Wake-on: d"
This patch checks whether the device can wakup, before using the
hard-coded supported flags. This corrects the ethtool reporting, as
well as the WOL configuration because ethtool verifies that the mode
is supported before attempting it.
Fixes: c51de7f3976b ("net: bcmgenet: add Wake-on-LAN support code") Signed-off-by: Jeremy Linton <jeremy.linton@arm.com> Tested-by: Peter Robinson <pbrobinson@gmail.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Link: https://lore.kernel.org/r/20220310045535.224450-1-jeremy.linton@arm.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The of_find_compatible_node() function returns a node pointer with
refcount incremented, We should use of_node_put() on it when done
Add the missing of_node_put() to release the refcount.
Fixes: 7349a74ea75c ("net: ethernet: gianfar_ethtool: get phc index through drvdata") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com> Link: https://lore.kernel.org/r/20220310015313.14938-1-linmq006@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
This works around an issue with the hardware where both OE and
DAT are exposed in the same register. If both are updated
simultaneously, the harware makes no guarantees that OE or DAT
will actually change in any given order and may result in a
glitch of a few ns on a GPIO pin when changing direction and value
in a single write.
Setting direction to input now only affects OE bit. Setting
direction to output updates DAT first, then OE.
The cleanup() function takes care of killing processes launched by the
test functions. It relies on variables like ${tcpdump_pids} to get the
relevant PIDs. But tests are run in their own subshell, so updated
*_pids values are invisible to other shells. Therefore cleanup() never
sees any process to kill:
Fix this by running cleanup() in the context of the test subshell.
Now that each test cleans the environment after completion, there's no
need for calling cleanup() again when the next test starts. So let's
drop it from the setup() function. This is okay because cleanup() is
also called when pmtu.sh starts, so even the first test starts in a
clean environment.
Also, use tcpdump's immediate mode. Otherwise it might not have time to
process buffered packets, resulting in missing packets or even empty
pcap files for short tests.
Note: PAUSE_ON_FAIL is still evaluated before cleanup(), so one can
still inspect the test environment upon failure when using -p.
Fixes: a92a0a7b8e7c ("selftests: pmtu: Simplify cleanup and namespace names") Signed-off-by: Guillaume Nault <gnault@redhat.com> Reviewed-by: Shuah Khan <skhan@linuxfoundation.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Syzbot reported UAF in port100_send_complete(). The root case is in
missing usb_kill_urb() calls on error handling path of ->probe function.
port100_send_complete() accesses devm allocated memory which will be
freed on probe failure. We should kill this urbs before returning an
error from probe function to prevent reported use-after-free
Fail log:
BUG: KASAN: use-after-free in port100_send_complete+0x16e/0x1a0 drivers/nfc/port100.c:935
Read of size 1 at addr ffff88801bb59540 by task ksoftirqd/2/26
...
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106
print_address_description.constprop.0.cold+0x8d/0x303 mm/kasan/report.c:255
__kasan_report mm/kasan/report.c:442 [inline]
kasan_report.cold+0x83/0xdf mm/kasan/report.c:459
port100_send_complete+0x16e/0x1a0 drivers/nfc/port100.c:935
__usb_hcd_giveback_urb+0x2b0/0x5c0 drivers/usb/core/hcd.c:1670
Fix a refcount use after free warning due to a race on command entry.
Such race occurs when one of the commands releases its last refcount and
frees its index and entry while another process running command flush
flow takes refcount to this command entry. The process which handles
commands flush may see this command as needed to be flushed if the other
process released its refcount but didn't release the index yet. Fix it
by adding the needed spin lock.
When two ax25 devices attempted to establish connection, the requester use ax25_create(),
ax25_bind() and ax25_connect() to initiate connection. The receiver use ax25_rcv() to
accept connection and use ax25_create_cb() in ax25_rcv() to create ax25_cb, but the
ax25_cb->sk is NULL. When the receiver is detaching, a NULL pointer dereference bug
caused by sock_hold(sk) in ax25_kill_by_device() will happen. The corresponding
fail log is shown below:
This patch add condition check in ax25_kill_by_device(). If s->sk is
NULL, it will goto if branch to kill device.
Fixes: 4e0f718daf97 ("ax25: improve the incomplete fix to avoid UAF and NPD bugs") Reported-by: Thomas Osterried <thomas@osterried.de> Signed-off-by: Duoming Zhou <duoming@zju.edu.cn> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
This node pointer is returned by of_parse_phandle() with refcount
incremented in this function. Calling of_node_put() to avoid the
refcount leak. As the remove function do.
Fixes: 5cdaaa12866e ("net: emaclite: adding MDIO and phy lib support") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20220308024751.2320-1-linmq006@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
[ 0.742963] aspeed-g6-pinctrl 1e6e2000.syscon:pinctrl: invalid function FWQSPID in map table

This is because the quad mode pins are a group of pins, not a function.
After applying this patch we can request the pins and the QSPI data
lines are muxed:
# cat /sys/kernel/debug/pinctrl/1e6e2000.syscon\:pinctrl-aspeed-g6-pinctrl/pinmux-pins |grep 1e620000.spi
pin 196 (AE12): device 1e620000.spi function FWSPID group FWQSPID
pin 197 (AF12): device 1e620000.spi function FWSPID group FWQSPID
pin 240 (Y1): device 1e620000.spi function FWSPID group FWQSPID
pin 241 (Y2): device 1e620000.spi function FWSPID group FWQSPID
pin 242 (Y3): device 1e620000.spi function FWSPID group FWQSPID
pin 243 (Y4): device 1e620000.spi function FWSPID group FWQSPID
Clang static analysis reports this issue
qed_sriov.c:4727:19: warning: Assigned value is
garbage or undefined
ivi->max_tx_rate = tx_rate ? tx_rate : link.speed;
^ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
link is only sometimes set by the call to qed_iov_get_link()
qed_iov_get_link fails without setting link or returning
status. So change the decl to return status.
Fixes: 73390ac9d82b ("qed*: support ndo_get_vf_config") Signed-off-by: Tom Rix <trix@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The function dma_alloc_coherent() in qed_vf_hw_prepare() can fail, so
its return value should be checked.
Fixes: 1408cc1fa48c ("qed: Introduce VFs") Reported-by: TOTE Robot <oslab@tsinghua.edu.cn> Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Currently the value of max_discard_segment will be set to
MAX_DISCARD_SEGMENTS (256) with no basis in hardware if device
set 0 to max_discard_seg in configuration space. It's incorrect
since the device might not be able to handle such large descriptors.
To fix it, let's follow max_segments restrictions in this case.
Fixes: 1f23816b8eb8 ("virtio_blk: add discard and write zeroes support") Signed-off-by: Xie Yongji <xieyongji@bytedance.com> Link: https://lore.kernel.org/r/20220304100058.116-1-xieyongji@bytedance.com Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
GDSCs have multiple transition delays which are used for the GDSC FSM
states. Older targets/designs required these values to be updated from
gdsc code to certain default values for the FSM state to work as
expected. But on the newer targets/designs the values updated from the
GDSC driver can hamper the FSM state to not work as expected.
On SC7180 we observe black screens because the gdsc is being
enabled/disabled very rapidly and the GDSC FSM state does not work as
expected. This is due to the fact that the GDSC reset value is being
updated from SW.
Thus add support to update the transition delay from the clock
controller gdscs as required.
Fixes: 45dd0e55317cc ("clk: qcom: Add support for GDSCs) Signed-off-by: Taniya Das <tdas@codeaurora.org> Link: https://lore.kernel.org/r/20220223185606.3941-1-tdas@codeaurora.org Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When calling gnttab_end_foreign_access_ref() the returned value must
be tested and the reaction to that value should be appropriate.
In case of failure in xennet_get_responses() the reaction should not be
to crash the system, but to disable the network device.
The calls in setup_netfront() can be replaced by calls of
gnttab_end_foreign_access(). While at it avoid double free of ring
pages and grant references via xennet_disconnect_backend() in this case.
This is CVE-2022-23042 / part of XSA-396.
Reported-by: Demi Marie Obenour <demi@invisiblethingslab.com> Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Jan Beulich <jbeulich@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
gnttab_end_foreign_access() is used to free a grant reference and
optionally to free the associated page. In case the grant is still in
use by the other side processing is being deferred. This leads to a
problem in case no page to be freed is specified by the caller: the
caller doesn't know that the page is still mapped by the other side
and thus should not be used for other purposes.
The correct way to handle this situation is to take an additional
reference to the granted page in case handling is being deferred and
to drop that reference when the grant reference could be freed
finally.
This requires that there are no users of gnttab_end_foreign_access()
left directly repurposing the granted page after the call, as this
might result in clobbered data or information leaks via the not yet
freed grant reference.
This is part of CVE-2022-23041 / XSA-396.
Reported-by: Simon Gaiser <simon@invisiblethingslab.com> Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Jan Beulich <jbeulich@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Instead of __get_free_pages() and free_pages() use alloc_pages_exact()
and free_pages_exact(). This is in preparation of a change of
gnttab_end_foreign_access() which will prohibit use of high-order
pages.
This is part of CVE-2022-23041 / XSA-396.
Reported-by: Simon Gaiser <simon@invisiblethingslab.com> Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Jan Beulich <jbeulich@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Instead of __get_free_pages() and free_pages() use alloc_pages_exact()
and free_pages_exact(). This is in preparation of a change of
gnttab_end_foreign_access() which will prohibit use of high-order
pages.
By using the local variable "order" instead of ring->intf->ring_order
in the error path of xen_9pfs_front_alloc_dataring() another bug is
fixed, as the error path can be entered before ring->intf->ring_order
is being set.
By using alloc_pages_exact() the size in bytes is specified for the
allocation, which fixes another bug for the case of
order < (PAGE_SHIFT - XEN_PAGE_SHIFT).
This is part of CVE-2022-23041 / XSA-396.
Reported-by: Simon Gaiser <simon@invisiblethingslab.com> Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Jan Beulich <jbeulich@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Remove gnttab_query_foreign_access(), as it is unused and unsafe to
use.
All previous use cases assumed a grant would not be in use after
gnttab_query_foreign_access() returned 0. This information is useless
in best case, as it only refers to a situation in the past, which could
have changed already.
Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Jan Beulich <jbeulich@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Using gnttab_query_foreign_access() is unsafe, as it is racy by design.
The use case in the gntalloc driver is not needed at all. While at it
replace the call of gnttab_end_foreign_access_ref() with a call of
gnttab_end_foreign_access(), which is what is really wanted there. In
case the grant wasn't used due to an allocation failure, just free the
grant via gnttab_free_grant_reference().
This is CVE-2022-23039 / part of XSA-396.
Reported-by: Demi Marie Obenour <demi@invisiblethingslab.com> Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Jan Beulich <jbeulich@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
It isn't enough to check whether a grant is still being in use by
calling gnttab_query_foreign_access(), as a mapping could be realized
by the other side just after having called that function.
In case the call was done in preparation of revoking a grant it is
better to do so via gnttab_try_end_foreign_access() and check the
success of that operation instead.
This is CVE-2022-23038 / part of XSA-396.
Reported-by: Demi Marie Obenour <demi@invisiblethingslab.com> Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Jan Beulich <jbeulich@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
It isn't enough to check whether a grant is still being in use by
calling gnttab_query_foreign_access(), as a mapping could be realized
by the other side just after having called that function.
In case the call was done in preparation of revoking a grant it is
better to do so via gnttab_end_foreign_access_ref() and check the
success of that operation instead.
This is CVE-2022-23037 / part of XSA-396.
Reported-by: Demi Marie Obenour <demi@invisiblethingslab.com> Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Jan Beulich <jbeulich@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
It isn't enough to check whether a grant is still being in use by
calling gnttab_query_foreign_access(), as a mapping could be realized
by the other side just after having called that function.
In case the call was done in preparation of revoking a grant it is
better to do so via gnttab_end_foreign_access_ref() and check the
success of that operation instead.
For the ring allocation use alloc_pages_exact() in order to avoid
high order pages in case of a multi-page ring.
If a grant wasn't unmapped by the backend without persistent grants
being used, set the device state to "error".
This is CVE-2022-23036 / part of XSA-396.
Reported-by: Demi Marie Obenour <demi@invisiblethingslab.com> Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Roger Pau Monné <roger.pau@citrix.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Add a new grant table function gnttab_try_end_foreign_access(), which
will remove and free a grant if it is not in use.
Its main use case is to either free a grant if it is no longer in use,
or to take some other action if it is still in use. This other action
can be an error exit, or (e.g. in the case of blkfront persistent grant
feature) some special handling.
This is CVE-2022-23036, CVE-2022-23038 / part of XSA-396.
Reported-by: Demi Marie Obenour <demi@invisiblethingslab.com> Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Jan Beulich <jbeulich@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Letting xenbus_grant_ring() tear down grants in the error case is
problematic, as the other side could already have used these grants.
Calling gnttab_end_foreign_access_ref() without checking success is
resulting in an unclear situation for any caller of xenbus_grant_ring()
as in the error case the memory pages of the ring page might be
partially mapped. Freeing them would risk unwanted foreign access to
them, while not freeing them would leak memory.
In order to remove the need to undo any gnttab_grant_foreign_access()
calls, use gnttab_alloc_grant_references() to make sure no further
error can occur in the loop granting access to the ring pages.
It should be noted that this way of handling removes leaking of
grant entries in the error case, too.
This is CVE-2022-23040 / part of XSA-396.
Reported-by: Demi Marie Obenour <demi@invisiblethingslab.com> Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Jan Beulich <jbeulich@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
projects / mirror_ubuntu-focal-kernel.git / log