Coverity complains of a possible buffer overflow. However,
given the 'static' scope of nvidia_setup_i2c_bus() it looks
like that can't happen after examiniing the call sites.
CID 19036 (#1 of 1): Copy into fixed size buffer (STRING_OVERFLOW)
1. fixed_size_dest: You might overrun the 48-character fixed-size string
chan->adapter.name by copying name without checking the length.
2. parameter_as_source: Note: This defect has an elevated risk because the
source argument is a parameter of the current function.
89 strcpy(chan->adapter.name, name);
Fix this warning by using strscpy() which will silence the warning and
prevent any future buffer overflows should the names used to identify the
channel become much longer.
Cc: Antonino Daplas <adaplas@gmail.com> Cc: linux-fbdev@vger.kernel.org Cc: dri-devel@lists.freedesktop.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Helge Deller <deller@gmx.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
[un]pin_user_pages_remote is dirtying pages without properly warning
the file system in advance. A related race was noted by Jan Kara in
2018[1]; however, more recently instead of it being a very hard-to-hit
race, it could be reliably triggered by process_vm_writev(2) which was
discovered by Syzbot[2].
This is technically a bug in mm/gup.c, but arguably ext4 is fragile in
that if some other kernel subsystem dirty pages without properly
notifying the file system using page_mkwrite(), ext4 will BUG, while
other file systems will not BUG (although data will still be lost).
So instead of crashing with a BUG, issue a warning (since there may be
potential data loss) and just mark the page as clean to avoid
unprivileged denial of service attacks until the problem can be
properly fixed. More discussion and background can be found in the
thread starting at [2].
The function device_pm_check_callbacks() can be called under the spin
lock (in the reported case it happens from genpd_add_device() ->
dev_pm_domain_set(), when the genpd uses spinlocks rather than mutexes.
However this function uncoditionally uses spin_lock_irq() /
spin_unlock_irq(), thus not preserving the CPU flags. Use the
irqsave/irqrestore instead.
Platforms with large BERT table data can trigger soft lockup errors
while attempting to print the entire BERT table data to the console at
boot:
watchdog: BUG: soft lockup - CPU#160 stuck for 23s! [swapper/0:1]
Observed on Ampere Altra systems with a single BERT record of ~250KB.
The original bert driver appears to have assumed relatively small table
data. Since it is impractical to reassemble large table data from
interwoven console messages, and the table data is available in
/sys/firmware/acpi/tables/data/BERT
limit the size for tables printed to the console to 1024 (for no reason
other than it seemed like a good place to kick off the discussion, would
appreciate feedback from existing users in terms of what size would
maintain their current usage model).
Alternatively, we could make printing a CONFIG option, use the
bert_disable boot arg (or something similar), or use a debug log level.
However, all those solutions require extra steps or change the existing
behavior for small table data. Limiting the size preserves existing
behavior on existing platforms with small table data, and eliminates the
soft lockups for platforms with large table data, while still making it
available.
Signed-off-by: Darren Hart <darren@os.amperecomputing.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
A crash [1] happened to be triggered in conjunction with commit 2d52c58b9c9b ("block, bfq: honor already-setup queue merges"). The
latter was then reverted by commit ebc69e897e17 ("Revert "block, bfq:
honor already-setup queue merges""). Yet, the reverted commit was not
the one introducing the bug. In fact, it actually triggered a UAF
introduced by a different commit, and now fixed by commit d29bd41428cf
("block, bfq: reset last_bfqq_created on group change").
So, there is no point in keeping commit 2d52c58b9c9b ("block, bfq:
honor already-setup queue merges") out. This commit restores it.
Buidling raid6test on Ubuntu 21.10 (ppc64le) with GNU Make 4.3 shows the
errors below:
$ cd lib/raid6/test/
$ make
<stdin>:1:1: error: stray ‘\’ in program
<stdin>:1:2: error: stray ‘#’ in program
<stdin>:1:11: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ \
before ‘<’ token
[...]
The errors come from the HAS_ALTIVEC test, which fails, and the POWER
optimized versions are not built. That’s also reason nobody noticed on the
other architectures.
GNU Make 4.3 does not remove the backslash anymore. From the 4.3 release
announcment:
> * WARNING: Backward-incompatibility!
> Number signs (#) appearing inside a macro reference or function invocation
> no longer introduce comments and should not be escaped with backslashes:
> thus a call such as:
> foo := $(shell echo '#')
> is legal. Previously the number sign needed to be escaped, for example:
> foo := $(shell echo '\#')
> Now this latter will resolve to "\#". If you want to write makefiles
> portable to both versions, assign the number sign to a variable:
> H := \#
> foo := $(shell echo '$H')
> This was claimed to be fixed in 3.81, but wasn't, for some reason.
> To detect this change search for 'nocomment' in the .FEATURES variable.
So, do the same as commit 9564a8cf422d ("Kbuild: fix # escaping in .cmd
files for future Make") and commit 929bef467771 ("bpf: Use $(pound) instead
of \# in Makefiles") and define and use a $(pound) variable.
Reference for the change in make:
https://git.savannah.gnu.org/cgit/make.git/commit/?id=c6966b323811c37acedff05b57
Cc: Matt Brown <matthew.brown.dev@gmail.com> Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de> Signed-off-by: Song Liu <song@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Prevent acpi_ns_walk_namespace() from crashing when called with
start_node equal to ACPI_ROOT_OBJECT if the Namespace has not been
instantiated yet and acpi_gbl_root_node is NULL.
For instance, this can happen if the kernel is run with "acpi=off"
in the command line.
KASAN reports a use-after-free report when doing normal scsi-mq test
[69832.239032] ==================================================================
[69832.241810] BUG: KASAN: use-after-free in bfq_dispatch_request+0x1045/0x44b0
[69832.243267] Read of size 8 at addr ffff88802622ba88 by task kworker/3:1H/155
[69832.244656]
[69832.245007] CPU: 3 PID: 155 Comm: kworker/3:1H Not tainted 5.10.0-10295-g576c6382529e #8
[69832.246626] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.14.0-0-g155821a1990b-prebuilt.qemu.org 04/01/2014
[69832.249069] Workqueue: kblockd blk_mq_run_work_fn
[69832.250022] Call Trace:
[69832.250541] dump_stack+0x9b/0xce
[69832.251232] ? bfq_dispatch_request+0x1045/0x44b0
[69832.252243] print_address_description.constprop.6+0x3e/0x60
[69832.253381] ? __cpuidle_text_end+0x5/0x5
[69832.254211] ? vprintk_func+0x6b/0x120
[69832.254994] ? bfq_dispatch_request+0x1045/0x44b0
[69832.255952] ? bfq_dispatch_request+0x1045/0x44b0
[69832.256914] kasan_report.cold.9+0x22/0x3a
[69832.257753] ? bfq_dispatch_request+0x1045/0x44b0
[69832.258755] check_memory_region+0x1c1/0x1e0
[69832.260248] bfq_dispatch_request+0x1045/0x44b0
[69832.261181] ? bfq_bfqq_expire+0x2440/0x2440
[69832.262032] ? blk_mq_delay_run_hw_queues+0xf9/0x170
[69832.263022] __blk_mq_do_dispatch_sched+0x52f/0x830
[69832.264011] ? blk_mq_sched_request_inserted+0x100/0x100
[69832.265101] __blk_mq_sched_dispatch_requests+0x398/0x4f0
[69832.266206] ? blk_mq_do_dispatch_ctx+0x570/0x570
[69832.267147] ? __switch_to+0x5f4/0xee0
[69832.267898] blk_mq_sched_dispatch_requests+0xdf/0x140
[69832.268946] __blk_mq_run_hw_queue+0xc0/0x270
[69832.269840] blk_mq_run_work_fn+0x51/0x60
[69832.278170] process_one_work+0x6d4/0xfe0
[69832.278984] worker_thread+0x91/0xc80
[69832.279726] ? __kthread_parkme+0xb0/0x110
[69832.280554] ? process_one_work+0xfe0/0xfe0
[69832.281414] kthread+0x32d/0x3f0
[69832.282082] ? kthread_park+0x170/0x170
[69832.282849] ret_from_fork+0x1f/0x30
[69832.283573]
[69832.283886] Allocated by task 7725:
[69832.284599] kasan_save_stack+0x19/0x40
[69832.285385] __kasan_kmalloc.constprop.2+0xc1/0xd0
[69832.286350] kmem_cache_alloc_node+0x13f/0x460
[69832.287237] bfq_get_queue+0x3d4/0x1140
[69832.287993] bfq_get_bfqq_handle_split+0x103/0x510
[69832.289015] bfq_init_rq+0x337/0x2d50
[69832.289749] bfq_insert_requests+0x304/0x4e10
[69832.290634] blk_mq_sched_insert_requests+0x13e/0x390
[69832.291629] blk_mq_flush_plug_list+0x4b4/0x760
[69832.292538] blk_flush_plug_list+0x2c5/0x480
[69832.293392] io_schedule_prepare+0xb2/0xd0
[69832.294209] io_schedule_timeout+0x13/0x80
[69832.295014] wait_for_common_io.constprop.1+0x13c/0x270
[69832.296137] submit_bio_wait+0x103/0x1a0
[69832.296932] blkdev_issue_discard+0xe6/0x160
[69832.297794] blk_ioctl_discard+0x219/0x290
[69832.298614] blkdev_common_ioctl+0x50a/0x1750
[69832.304715] blkdev_ioctl+0x470/0x600
[69832.305474] block_ioctl+0xde/0x120
[69832.306232] vfs_ioctl+0x6c/0xc0
[69832.306877] __se_sys_ioctl+0x90/0xa0
[69832.307629] do_syscall_64+0x2d/0x40
[69832.308362] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[69832.309382]
[69832.309701] Freed by task 155:
[69832.310328] kasan_save_stack+0x19/0x40
[69832.311121] kasan_set_track+0x1c/0x30
[69832.311868] kasan_set_free_info+0x1b/0x30
[69832.312699] __kasan_slab_free+0x111/0x160
[69832.313524] kmem_cache_free+0x94/0x460
[69832.314367] bfq_put_queue+0x582/0x940
[69832.315112] __bfq_bfqd_reset_in_service+0x166/0x1d0
[69832.317275] bfq_bfqq_expire+0xb27/0x2440
[69832.318084] bfq_dispatch_request+0x697/0x44b0
[69832.318991] __blk_mq_do_dispatch_sched+0x52f/0x830
[69832.319984] __blk_mq_sched_dispatch_requests+0x398/0x4f0
[69832.321087] blk_mq_sched_dispatch_requests+0xdf/0x140
[69832.322225] __blk_mq_run_hw_queue+0xc0/0x270
[69832.323114] blk_mq_run_work_fn+0x51/0x60
[69832.323942] process_one_work+0x6d4/0xfe0
[69832.324772] worker_thread+0x91/0xc80
[69832.325518] kthread+0x32d/0x3f0
[69832.326205] ret_from_fork+0x1f/0x30
[69832.326932]
[69832.338297] The buggy address belongs to the object at ffff88802622b968
[69832.338297] which belongs to the cache bfq_queue of size 512
[69832.340766] The buggy address is located 288 bytes inside of
[69832.340766] 512-byte region [ffff88802622b968, ffff88802622bb68)
[69832.343091] The buggy address belongs to the page:
[69832.344097] page:ffffea0000988a00 refcount:1 mapcount:0 mapping:0000000000000000 index:0xffff88802622a528 pfn:0x26228
[69832.346214] head:ffffea0000988a00 order:2 compound_mapcount:0 compound_pincount:0
[69832.347719] flags: 0x1fffff80010200(slab|head)
[69832.348625] raw: 001fffff80010200ffffea0000dbac08ffff888017a57650ffff8880179fe840
[69832.354972] raw: ffff88802622a528000000000012000800000001ffffffff0000000000000000
[69832.356547] page dumped because: kasan: bad access detected
[69832.357652]
[69832.357970] Memory state around the buggy address:
[69832.358926] ffff88802622b980: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[69832.360358] ffff88802622ba00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[69832.361810] >ffff88802622ba80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[69832.363273] ^
[69832.363975] ffff88802622bb00: fb fb fb fb fb fb fb fb fb fb fb fb fb fc fc fc
[69832.375960] ffff88802622bb80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[69832.377405] ==================================================================
In bfq_dispatch_requestfunction, it may have function call:
bfq_dispatch_request
__bfq_dispatch_request
bfq_select_queue
bfq_bfqq_expire
__bfq_bfqd_reset_in_service
bfq_put_queue
kmem_cache_free
In this function call, in_serv_queue has beed expired and meet the
conditions to free. In the function bfq_dispatch_request, the address
of in_serv_queue pointing to has been released. For getting the value
of idle_timer_disabled, it will get flags value from the address which
in_serv_queue pointing to, then the problem of use-after-free happens;
Fix the problem by check in_serv_queue == bfqd->in_service_queue, to
get the value of idle_timer_disabled if in_serve_queue is equel to
bfqd->in_service_queue. If the space of in_serv_queue pointing has
been released, this judge will aviod use-after-free problem.
And if in_serv_queue may be expired or finished, the idle_timer_disabled
will be false which would not give effects to bfq_update_dispatch_stats.
Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Zhang Wensheng <zhangwensheng5@huawei.com> Link: https://lore.kernel.org/r/20220303070334.3020168-1-zhangwensheng5@huawei.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
pdc_enable_intr() serves as a primitive to qcom_pdc_gic_{en,dis}able,
and has a raw spinlock for mutual exclusion, which is uses with
interruptible primitives.
This means that this critical section can itself be interrupted.
Should the interrupt also be a PDC interrupt, and the endpoint driver
perform an irq_disable() on that interrupt, we end-up in a deadlock.
Fix this by using the irqsave/irqrestore variants of the locking
primitives.
Signed-off-by: Marc Zyngier <maz@kernel.org> Reviewed-by: Maulik Shah <quic_mkshah@quicinc.com> Link: https://lore.kernel.org/r/20220224101226.88373-5-maz@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
sprintf does not know the PAGE_SIZE maximum of the temporary buffer
used for outputting sysfs content and it's possible to overrun the
PAGE_SIZE buffer length.
Use a generic sysfs_emit function that knows the size of the
temporary buffer and ensures that no overrun is done for offset
attribute in
loop_attr_[offset|sizelimit|autoclear|partscan|dio]_show() callbacks.
security_sid_to_context() expects a pointer to an u32 as the address
where to store the length of the computed context.
Reported by sparse:
security/selinux/xfrm.c:359:39: warning: incorrect type in arg 4
(different signedness)
security/selinux/xfrm.c:359:39: expected unsigned int
[usertype] *scontext_len
security/selinux/xfrm.c:359:39: got int *
Signed-off-by: Christian Göttsche <cgzones@googlemail.com>
[PM: wrapped commit description] Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The npcm driver has a bunch of references to the irq_chip parent_device
field, but never sets it.
Fix it by fishing that reference from somewhere else, but it is
obvious that these debug statements were never used. Also remove
an unused field in a local data structure.
Signed-off-by: Marc Zyngier <maz@kernel.org> Acked-by: Bartosz Golaszewski <brgl@bgdev.pl> Link: https://lore.kernel.org/r/20220201120310.878267-11-maz@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Since STRING_CST may not be NUL terminated, strncmp() was used for check
for equality. However, this may lead to mismatches for longer section
names where the start matches the tested-for string. Test for exact
equality by checking for the presences of NUL termination.
Cc: Alexander Popov <alex.popov@linux.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The usual LSM hook "bail on fail" scheme doesn't work for cases where
a security module may return an error code indicating that it does not
recognize an input. In this particular case Smack sees a mount option
that it recognizes, and returns 0. A call to a BPF hook follows, which
returns -ENOPARAM, which confuses the caller because Smack has processed
its data.
The SELinux hook incorrectly returns 1 on success. There was a time
when this was correct, however the current expectation is that it
return 0 on success. This is repaired.
Reported-by: syzbot+d1e3b1d92d25abf97943@syzkaller.appspotmail.com Signed-off-by: Casey Schaufler <casey@schaufler-ca.com> Acked-by: James Morris <jamorris@linux.microsoft.com> Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The "test_dev" pointer is freed but then returned to the caller.
Fixes: d9c6a72d6fa2 ("kmod: add test driver to stress test the module loader") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Luis Chamberlain <mcgrof@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The list iterator value 'rule' will *always* be set and non-NULL
by list_for_each_entry(), so it is incorrect to assume that the
iterator value will be NULL if the list is empty or no element
is found.
To fix the bug, return 'rule' when found, otherwise return NULL.
Fixes: ae7a5aff783c7 ("net: dsa: bcm_sf2: Keep copy of inserted rules") Reviewed-by: Vladimir Oltean <olteanv@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Xiaomeng Tong <xiam0nd.tong@gmail.com> Link: https://lore.kernel.org/r/20220328032431.22538-1-xiam0nd.tong@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
In nfs4_callback_devicenotify(), if we don't find a matching entry for
the deviceid, we're left with a pointer to 'struct nfs_server' that
actually points to the list of super blocks associated with our struct
nfs_client.
Furthermore, even if we have a valid pointer, nothing pins the super
block, and so the struct nfs_server could end up getting freed while
we're using it.
Since all we want is a pointer to the struct pnfs_layoutdriver_type,
let's skip all the iteration over super blocks, and just use APIs to
find the layout driver directly.
When the link layer is terminating, x25->neighbour will be set to NULL
in x25_disconnect(). As a result, it could cause null-ptr-deref bugs in
x25_sendmsg(),x25_recvmsg() and x25_connect(). One of the bugs is
shown below.
The code sets NULL to x25->neighbour in position (1) and dereferences
x25->neighbour in position (2), which could cause null-ptr-deref bug.
This patch adds lock_sock() in x25_kill_by_neigh() in order to synchronize
with x25_sendmsg(), x25_recvmsg() and x25_connect(). What`s more, the
sock held by lock_sock() is not NULL, because it is extracted from x25_list
and uses x25_list_lock to synchronize.
Fixes: 4becb7ee5b3d ("net/x25: Fix x25_neigh refcnt leak when x25 disconnect") Signed-off-by: Duoming Zhou <duoming@zju.edu.cn> Reviewed-by: Lin Ma <linma@zju.edu.cn> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Clang static analysis reports this issue
qlcnic_dcb.c:382:10: warning: Assigned value is
garbage or undefined
mbx_out = *val;
^ ~~~~
val is set in the qlcnic_dcb_query_hw_capability() wrapper.
If there is no query_hw_capability op in dcp, success is
returned without setting the val.
For this and similar wrappers, return -EOPNOTSUPP.
Fixes: 14d385b99059 ("qlcnic: dcb: Query adapter DCB capabilities.") Signed-off-by: Tom Rix <trix@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The purpose of the last test case is to test VXLAN encapsulation and
decapsulation when the underlay lookup takes place in a non-default VRF.
This is achieved by enslaving the physical device of the tunnel to a
VRF.
The binding of the VXLAN UDP socket to the VRF happens when the VXLAN
device itself is opened, not when its physical device is opened. This
was also mentioned in the cited commit ("tests that moving the underlay
from a VRF to another works when down/up the VXLAN interface"), but the
test did something else.
Fix it by reopening the VXLAN device instead of its physical device.
Before:
# ./test_vxlan_under_vrf.sh
Checking HV connectivity [ OK ]
Check VM connectivity through VXLAN (underlay in the default VRF) [ OK ]
Check VM connectivity through VXLAN (underlay in a VRF) [FAIL]
After:
# ./test_vxlan_under_vrf.sh
Checking HV connectivity [ OK ]
Check VM connectivity through VXLAN (underlay in the default VRF) [ OK ]
Check VM connectivity through VXLAN (underlay in a VRF) [ OK ]
Fixes: 03f1c26b1c56 ("test/net: Add script for VXLAN underlay in a VRF") Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: David Ahern <dsahern@kernel.org> Link: https://lore.kernel.org/r/20220324200514.1638326-1-idosch@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
A Broadcom AC201 PHY (same entry as 5241) would be flagged by the
Broadcom UniMAC MDIO controller as not completing the turn around
properly since the PHY expects 65 MDC clock cycles to complete a write
cycle, and the MDIO controller was only sending 64 MDC clock cycles as
determined by looking at a scope shot.
This would make the subsequent read fail with the UniMAC MDIO controller
command field having MDIO_READ_FAIL set and we would abort the
brcm_fet_config_init() function and thus not probe the PHY at all.
After issuing a software reset, wait for at least 1ms which is well
above the 1us reset delay advertised by the datasheet and issue a dummy
read to let the PHY turn around the line properly. This read
specifically ignores -EIO which would be returned by MDIO controllers
checking for the line being turned around.
If we have a genuine reaad failure, the next read of the interrupt
status register would pick it up anyway.
Fixes: d7a2ed9248a3 ("broadcom: Add AC131 phy support") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Link: https://lore.kernel.org/r/20220324232438.1156812-1-f.fainelli@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
is_xen_pmu() is taking the cpu number as parameter, but it is not using
it. Instead it just tests whether the Xen PMU initialization on the
current cpu did succeed. As this test is done by checking a percpu
pointer, preemption needs to be disabled in order to avoid switching
the cpu while doing the test. While resuming from suspend() this seems
not to be the case:
[ 88.082751] ACPI: PM: Low-level resume complete
[ 88.087933] ACPI: EC: EC started
[ 88.091464] ACPI: PM: Restoring platform NVS memory
[ 88.097166] xen_acpi_processor: Uploading Xen processor PM info
[ 88.103850] Enabling non-boot CPUs ...
[ 88.108128] installing Xen timer for CPU 1
[ 88.112763] BUG: using smp_processor_id() in preemptible [00000000] code: systemd-sleep/7138
[ 88.122256] caller is is_xen_pmu+0x12/0x30
[ 88.126937] CPU: 0 PID: 7138 Comm: systemd-sleep Tainted: G W 5.16.13-2.fc32.qubes.x86_64 #1
[ 88.137939] Hardware name: Star Labs StarBook/StarBook, BIOS 7.97 03/21/2022
[ 88.145930] Call Trace:
[ 88.148757] <TASK>
[ 88.151193] dump_stack_lvl+0x48/0x5e
[ 88.155381] check_preemption_disabled+0xde/0xe0
[ 88.160641] is_xen_pmu+0x12/0x30
[ 88.164441] xen_smp_intr_init_pv+0x75/0x100
Fix that by replacing is_xen_pmu() by a simple boolean variable which
reflects the Xen PMU initialization state on cpu 0.
Modify xen_pmu_init() to return early in case it is being called for a
cpu other than cpu 0 and the boolean variable not being set.
Fixes: bf6dfb154d93 ("xen/PMU: PMU emulation code") Reported-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com> Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Link: https://lore.kernel.org/r/20220325142002.31789-1-jgross@suse.com Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When registering a clock that doesn't have a recalc_rate implementation,
and doesn't have its parent registered yet, we initialize the clk_core
rate and 'req_rate' fields to 0.
The rate field is later updated when the parent is registered in
clk_core_reparent_orphans_nolock() using __clk_recalc_rates(), but the
'req_rate' field is never updated.
This leads to an issue in clk_set_rate_range() and clk_put(), since
those functions will call clk_set_rate() with the content of 'req_rate'
to provide drivers with the opportunity to change the rate based on the
new boundaries. In this case, we would call clk_set_rate() with a rate
of 0, effectively enforcing the minimum allowed for this clock whenever
we would call one of those two functions, even though the actual rate
might be within range.
Let's fix this by setting 'req_rate' in
clk_core_reparent_orphans_nolock() with the rate field content just
updated by the call to __clk_recalc_rates().
Fixes: 1c8e600440c7 ("clk: Add rate constraints to clocks") Reported-by: Dmitry Osipenko <dmitry.osipenko@collabora.com> Tested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com> # T30 Nexus7 Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://lore.kernel.org/r/20220325161144.1901695-2-maxime@cerno.tech
[sboyd@kernel.org: Reword comment] Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Fixes: aec89f78cf01 ("clk: qcom: Add support for msm8994 global clock controller") Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org> Link: https://lore.kernel.org/r/20220319174940.341137-1-konrad.dybcio@somainline.org Tested-by: Petr Vorel <petr.vorel@gmail.com> Reviewed-by: Petr Vorel <petr.vorel@gmail.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Do not reset IP_CT_TCP_FLAG_BE_LIBERAL flag in out-of-sync scenarios
coming before the TCP window tracking, otherwise such connections will
fail in the window check.
Update tcp_options() to leave this flag in place and add a new helper
function to reset the tcp window state.
Based on patch from Sven Auhagen.
Fixes: c4832c7bbc3f ("netfilter: nf_ct_tcp: improve out-of-sync situation in TCP tracking") Tested-by: Sven Auhagen <sven.auhagen@voleatech.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Syzbot reported divide error in dbNextAG(). The problem was in missing
validation check for malicious image.
Syzbot crafted an image with bmp->db_numag equal to 0. There wasn't any
validation checks, but dbNextAG() blindly use bmp->db_numag in divide
expression
Fix it by validating bmp->db_numag in dbMount() and return an error if
image is malicious
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Reported-and-tested-by: syzbot+46f5c25af73eb8330eb6@syzkaller.appspotmail.com Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When "driver_async_probe=nulltty" is used on the kernel boot command line,
it causes an Unknown parameter message and the string is added to init's
environment strings, polluting them.
Unknown kernel command line parameters "BOOT_IMAGE=/boot/bzImage-517rc6
driver_async_probe=nulltty", will be passed to user space.
Run /sbin/init as init process
with arguments:
/sbin/init
with environment:
HOME=/
TERM=linux
BOOT_IMAGE=/boot/bzImage-517rc6
driver_async_probe=nulltty
Change the return value of the __setup function to 1 to indicate
that the __setup option has been handled.
Link: lore.kernel.org/r/64644a2f-4a20-bab3-1e15-3b2cdd0defe3@omprussia.ru Fixes: 1ea61b68d0f8 ("async: Add cmdline option to specify drivers to be async probed") Cc: Feng Tang <feng.tang@intel.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: "Rafael J. Wysocki" <rafael@kernel.org> Reported-by: Igor Zhbanov <i.zhbanov@omprussia.ru> Reviewed-by: Feng Tang <feng.tang@intel.com> Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Link: https://lore.kernel.org/r/20220301041829.15137-1-rdunlap@infradead.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The Google Coreboot implementation requires IOMEM functions
(memmremap, memunmap, devm_memremap), but does not specify this is its
Kconfig. This results in build errors when HAS_IOMEM is not set, such as
on some UML configurations:
/usr/bin/ld: drivers/firmware/google/coreboot_table.o: in function `coreboot_table_probe':
coreboot_table.c:(.text+0x311): undefined reference to `memremap'
/usr/bin/ld: coreboot_table.c:(.text+0x34e): undefined reference to `memunmap'
/usr/bin/ld: drivers/firmware/google/memconsole-coreboot.o: in function `memconsole_probe':
memconsole-coreboot.c:(.text+0x12d): undefined reference to `memremap'
/usr/bin/ld: memconsole-coreboot.c:(.text+0x17e): undefined reference to `devm_memremap'
/usr/bin/ld: memconsole-coreboot.c:(.text+0x191): undefined reference to `memunmap'
/usr/bin/ld: drivers/firmware/google/vpd.o: in function `vpd_section_destroy.isra.0':
vpd.c:(.text+0x300): undefined reference to `memunmap'
/usr/bin/ld: drivers/firmware/google/vpd.o: in function `vpd_section_init':
vpd.c:(.text+0x382): undefined reference to `memremap'
/usr/bin/ld: vpd.c:(.text+0x459): undefined reference to `memunmap'
/usr/bin/ld: drivers/firmware/google/vpd.o: in function `vpd_probe':
vpd.c:(.text+0x59d): undefined reference to `memremap'
/usr/bin/ld: vpd.c:(.text+0x5d3): undefined reference to `memunmap'
collect2: error: ld returned 1 exit status
Fixes: a28aad66da8b ("firmware: coreboot: Collapse platform drivers into bus core") Acked-By: anton ivanov <anton.ivanov@cambridgegreys.com> Acked-By: Julius Werner <jwerner@chromium.org> Signed-off-by: David Gow <davidgow@google.com> Link: https://lore.kernel.org/r/20220225041502.1901806-1-davidgow@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
__setup() handlers should return 1 to indicate that the boot option
has been handled. A return of 0 causes the boot option/value to be
listed as an Unknown kernel parameter and added to init's (limited)
environment strings. So return 1 from kgdbts_option_setup().
Unknown kernel command line parameters "BOOT_IMAGE=/boot/bzImage-517rc7
kgdboc=kbd kgdbts=", will be passed to user space.
Run /sbin/init as init process
with arguments:
/sbin/init
with environment:
HOME=/
TERM=linux
BOOT_IMAGE=/boot/bzImage-517rc7
kgdboc=kbd
kgdbts=
Link: lore.kernel.org/r/64644a2f-4a20-bab3-1e15-3b2cdd0defe3@omprussia.ru Fixes: e8d31c204e36 ("kgdb: add kgdb internal test suite") Cc: kgdb-bugreport@lists.sourceforge.net Cc: Jason Wessel <jason.wessel@windriver.com> Cc: Daniel Thompson <daniel.thompson@linaro.org> Cc: Douglas Anderson <dianders@chromium.org> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Reported-by: Igor Zhbanov <i.zhbanov@omprussia.ru> Reviewed-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Link: https://lore.kernel.org/r/20220308033255.22118-1-rdunlap@infradead.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
__setup() handlers should return 1 to obsolete_checksetup() in
init/main.c to indicate that the boot option has been handled.
A return of 0 causes the boot option/value to be listed as an Unknown
kernel parameter and added to init's (limited) environment strings.
So return 1 from kgdboc_option_setup().
Unknown kernel command line parameters "BOOT_IMAGE=/boot/bzImage-517rc7
kgdboc=kbd kgdbts=", will be passed to user space.
Run /sbin/init as init process
with arguments:
/sbin/init
with environment:
HOME=/
TERM=linux
BOOT_IMAGE=/boot/bzImage-517rc7
kgdboc=kbd
kgdbts=
Link: lore.kernel.org/r/64644a2f-4a20-bab3-1e15-3b2cdd0defe3@omprussia.ru Fixes: 1bd54d851f50 ("kgdboc: Passing ekgdboc to command line causes panic") Fixes: f2d937f3bf00 ("consoles: polling support, kgdboc") Cc: He Zhe <zhe.he@windriver.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jirislaby@kernel.org> Cc: kgdb-bugreport@lists.sourceforge.net Cc: Jason Wessel <jason.wessel@windriver.com> Cc: Daniel Thompson <daniel.thompson@linaro.org> Cc: Douglas Anderson <dianders@chromium.org> Cc: linux-serial@vger.kernel.org Reported-by: Igor Zhbanov <i.zhbanov@omprussia.ru> Reviewed-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Link: https://lore.kernel.org/r/20220309033018.17936-1-rdunlap@infradead.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
__setup() handlers should return 1 to indicate that the boot option
has been handled or 0 to indicate that it was not handled.
Add a pr_warn() message if the option value is invalid and then
always return 1.
Link: lore.kernel.org/r/64644a2f-4a20-bab3-1e15-3b2cdd0defe3@omprussia.ru Fixes: 86b40567b917 ("tty: replace strict_strtoul() with kstrtoul()") Cc: Jingoo Han <jg1.han@samsung.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jirislaby@kernel.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Julian Wiedmann <jwi@linux.ibm.com> Cc: Vasily Gorbik <gor@linux.ibm.com> Cc: linuxppc-dev@lists.ozlabs.org Reported-by: Igor Zhbanov <i.zhbanov@omprussia.ru> Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Link: https://lore.kernel.org/r/20220308024228.20477-1-rdunlap@infradead.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The device_node pointer is returned by of_parse_phandle() with refcount
incremented. We should use of_node_put() on it when done.
Fixes: 1e747e59cc4d ("pinctrl: rockchip: base regmap supplied by a syscon") Fixes: 14dee8677e19 ("pinctrl: rockchip: let pmu registers be supplied by a syscon") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Link: https://lore.kernel.org/r/20220307120234.28657-1-linmq006@gmail.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
mtk_pconf_group_get(), used to read back pingroup pin config state,
simply returns a set of configs saved from a previous invocation of
mtk_pconf_group_set(). This is an unfiltered, unvalidated set passed
in from the pinconf core, which does not match the current hardware
state.
Since the driver library is designed to have one pin per group, pass
through mtk_pconf_group_get() to mtk_pinconf_get(), to read back the
current pin config state of the only pin in the group.
Also drop the assignment of pin config state to the group.
Fixes: 805250982bb5 ("pinctrl: mediatek: add pinctrl-paris that implements the vendor dt-bindings") Signed-off-by: Chen-Yu Tsai <wenst@chromium.org> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Link: https://lore.kernel.org/r/20220308100956.2750295-5-wenst@chromium.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
For mtk_pinconf_get(), the "argument" argument is typically returned by
pinconf_to_config_argument(), which holds the value for a given pinconf
parameter. It certainly should not have the type of "enum pin_config_param",
which describes the type of the pinconf parameter itself.
Change the type to u32, which matches the return type of
pinconf_to_config_argument().
Fixes: 805250982bb5 ("pinctrl: mediatek: add pinctrl-paris that implements the vendor dt-bindings") Signed-off-by: Chen-Yu Tsai <wenst@chromium.org> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Link: https://lore.kernel.org/r/20220308100956.2750295-4-wenst@chromium.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Fix LED and pinctrl definitions on the GB-PC1 devicetree. Refer to the
schematics of the device for more information.
LED fixes:
- Change GPIO6 LED label from system to power as GPIO6 is connected to
PLED.
- Add default-on default-trigger to power LED.
- Change GPIO8 LED label from status to system as GPIO8 is connected to
SYS_LED.
- Add disk-activity default-trigger to system LED.
- Switch to the color:function naming scheme.
- Remove lan1 and lan2 LEDs as they don't exist.
Pinctrl fixes:
- Claim state_default node under pinctrl node.
- Change pinctrl0 node name to state-default.
- Change gpio node name to gpio-pinmux to respect
Documentation/devicetree/bindings/pinctrl/ralink,rt2880-pinmux.yaml.
- Sort pin groups alphabetically.
Misc fixes:
- Fix formatting.
- Use the status value "okay".
- Define hexadecimal addresses in lower case.
- Make hexadecimal addresses for memory easier to read.
The reference taken by 'of_find_device_by_node()' must be released when
not needed anymore.
Add the corresponding 'put_device()' in the error handling path.
Fixes: 2db04f16b589 ("clk: tegra: Add EMC clock driver") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Acked-by: Thierry Reding <treding@nvidia.com> Link: https://lore.kernel.org/r/20220112104501.30655-1-linmq006@gmail.com Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The display pixel clock has a requirement on certain newer platforms to
support M/N as (2/3) and the final D value calculated results in
underflow errors.
As the current implementation does not check for D value is within
the accepted range for a given M & N value. Update the logic to
calculate the final D value based on the range.
Fixes: 99cbd064b059f ("clk: qcom: Support display RCG clocks") Signed-off-by: Taniya Das <tdas@codeaurora.org> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/20220227175536.3131-1-tdas@codeaurora.org Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The audio_mclk_root_clk was added as a gate with the CCGR121 (0x4790),
but according to the reference manual, there is no such gate. The
CCGR121 belongs to ECSPI2 and it is not shared.
Fixes: 8f6d8094b215b57 ("ARM: imx: add imx7d clk tree support") Reported-by: David Wolfe <david.wolfe@nxp.com> Signed-off-by: Abel Vesa <abel.vesa@nxp.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Link: https://lore.kernel.org/r/20220127141052.1900174-2-abel.vesa@nxp.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When valid kernel command line parameters
dma_debug=off dma_debug_entries=100
are used, they are reported as Unknown parameters and added to init's
environment strings, polluting it.
Unknown kernel command line parameters "BOOT_IMAGE=/boot/bzImage-517rc5
dma_debug=off dma_debug_entries=100", will be passed to user space.
and
Run /sbin/init as init process
with arguments:
/sbin/init
with environment:
HOME=/
TERM=linux
BOOT_IMAGE=/boot/bzImage-517rc5
dma_debug=off
dma_debug_entries=100
Return 1 from these __setup handlers to indicate that the command line
option has been handled.
Fixes: 59d3daafa1726 ("dma-debug: add kernel command line parameters") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Reported-by: Igor Zhbanov <i.zhbanov@omprussia.ru>
Link: lore.kernel.org/r/64644a2f-4a20-bab3-1e15-3b2cdd0defe3@omprussia.ru Cc: Joerg Roedel <joro@8bytes.org> Cc: Christoph Hellwig <hch@lst.de> Cc: Marek Szyprowski <m.szyprowski@samsung.com> Cc: iommu@lists.linux-foundation.org Cc: Robin Murphy <robin.murphy@arm.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Set em485->active_timer = NULL isn't always enough to take out the stop
timer. While there is a check that it acts in the right state (i.e.
waiting for RTS-after-send to pass after sending some chars) but the
following might happen:
- CPU1: some chars send, shifter becomes empty, stop tx timer armed
- CPU0: more chars send before RTS-after-send expired
- CPU0: shifter empty irq, port lock taken
- CPU1: tx timer triggers, waits for port lock
- CPU0: em485->active_timer = &em485->stop_tx_timer, hrtimer_start(),
releases lock()
- CPU1: get lock, see em485->active_timer == &em485->stop_tx_timer,
tear down RTS too early
This fix bases on research done by Steffen Trumtrar.
According to the comment of the function phy_mipi_dphy_get_default_config(),
it uses minimum D-PHY timings based on MIPI D-PHY specification. They are
derived from the valid ranges specified in Section 6.9, Table 14, Page 41
of the D-PHY specification (v1.2). The table 14 explicitly mentions that
the minimum T-LPX parameter is 50 nanoseconds and the minimum TA-SURE
parameter is T-LPX nanoseconds. Likewise, the kernel doc of the 'lpx' and
'ta_sure' members of struct phy_configure_opts_mipi_dphy mentions that
the minimum values are 50000 picoseconds and @lpx picoseconds respectively.
Also, the function phy_mipi_dphy_config_validate() checks if cfg->lpx is
less than 50000 picoseconds and if cfg->ta_sure is less than cfg->lpx,
which hints the same minimum values.
Without this patch, the function phy_mipi_dphy_get_default_config()
wrongly sets cfg->lpx to 60000 picoseconds and cfg->ta_sure to 2 * cfg->lpx.
So, let's correct them to 50000 picoseconds and cfg->lpx respectively.
Note that I've only tested the patch with RM67191 DSI panel on i.MX8mq EVK.
Help is needed to test with other i.MX8mq, Meson and Rockchip platforms,
as I don't have the hardwares.
Fixes: dddc97e82303 ("phy: dphy: Add configuration helpers") Cc: Andrzej Hajda <andrzej.hajda@intel.com> Cc: Neil Armstrong <narmstrong@baylibre.com> Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com> Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: Vinod Koul <vkoul@kernel.org> Cc: Heiko Stuebner <heiko@sntech.de> Cc: Maxime Ripard <mripard@kernel.org> Cc: Guido Günther <agx@sigxcpu.org> Signed-off-by: Liu Ying <victor.liu@nxp.com> Link: https://lore.kernel.org/r/20220216071257.1647703-1-victor.liu@nxp.com Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Use floor ops on SDCC1 APPS clock in order to round down selected clock
frequency and avoid overclocking SD/eMMC cards.
For example, currently HS200 cards were failling tuning as they were
actually being clocked at 384MHz instead of 192MHz.
This caused some boards to disable 1.8V I/O and force the eMMC into the
standard HS mode (50MHz) and that appeared to work despite the eMMC being
overclocked to 96Mhz in that case.
There was a previous commit to use floor ops on SDCC clocks, but it looks
to have only covered SDCC2 clock.
Fixes: 9607f6224b39 ("clk: qcom: ipq8074: add PCIE, USB and SDCC clocks") Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de> Signed-off-by: Robert Marko <robimarko@gmail.com> Reviewed-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/20220210173100.505128-1-robimarko@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The second video-in channel on RZ/G1C has only 12 data lanes, but the
pin control driver uses the vin_data union, which is meant for 24 data
lanes, thus wasting space.
The bit reversal was wrong for bits 1 and 3 of the 5 bits.
Result is driver failure to probe if you have more than 2 daisy-chained
devices. Discovered via QEMU based device emulation.
Fixes tag is for when this moved from a macro to a function, but it
was broken before that.
When a driver calls pwmchip_add() it has to be prepared to immediately
get its callbacks called. So move allocation of driver data and hardware
initialization before the call to pwmchip_add().
This fixes a potential NULL pointer exception and a race condition on
register writes.
When LSR is 0xff in ->activate() (rather unlike), we return an error.
Provided ->shutdown() is not called when ->activate() fails, nothing
actually frees the buffer in this case.
Fix this by properly freeing the buffer in a designated label. We jump
there also from the "!info->type" if now too.
Fixes: 6769140d3047 ("tty: mxser: use the tty_port_open method") Signed-off-by: Jiri Slaby <jslaby@suse.cz> Link: https://lore.kernel.org/r/20220124071430.14907-6-jslaby@suse.cz Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
In the timer callback function tipc_sk_timeout(), we're trying to
reschedule another timeout to retransmit a setup request if destination
link is congested. But we use the incorrect timeout value
(msecs_to_jiffies(100)) instead of (jiffies + msecs_to_jiffies(100)),
so that the timer expires immediately, it's irrelevant for original
description.
In this commit we correct the timeout value in sk_reset_timer()
Fixes: 6787927475e5 ("tipc: buffer overflow handling in listener socket") Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au> Link: https://lore.kernel.org/r/20220321042229.314288-1-hoang.h.le@dektech.com.au Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
During NAT, a tuple collision may occur. When this happens, openvswitch
will make a second pass through NAT which will perform additional packet
modification. This will update the skb data, but not the flow key that
OVS uses. This means that future flow lookups, and packet matches will
have incorrect data. This has been supported since 5d50aa83e2c8 ("openvswitch: support asymmetric conntrack").
That commit failed to properly update the sw_flow_key attributes, since
it only called the ovs_ct_nat_update_key once, rather than each time
ovs_ct_nat_execute was called. As these two operations are linked, the
ovs_ct_nat_execute() function should always make sure that the
sw_flow_key is updated after a successful call through NAT infrastructure.
Fixes: 5d50aa83e2c8 ("openvswitch: support asymmetric conntrack") Cc: Dumitru Ceara <dceara@redhat.com> Cc: Numan Siddique <nusiddiq@redhat.com> Signed-off-by: Aaron Conole <aconole@redhat.com> Acked-by: Eelco Chaudron <echaudro@redhat.com> Link: https://lore.kernel.org/r/20220318124319.3056455-1-aconole@redhat.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
After recent fixes to ICMPv6 PTB handling we started dropping
PMTU updates higher than tp->mss_cache. Because of the stale
tp->mss_cache value PMTU updates during TFO are always dropped.
Thanks to Wei for helping zero in on the problem and the fix!
Fixes: c7bb4b89033b ("ipv6: tcp: drop silly ICMPv6 packet too big messages") Reported-by: Andre Nash <alnash@fb.com> Reported-by: Neil Spring <ntspring@fb.com> Reviewed-by: Wei Wang <weiwan@google.com> Acked-by: Yuchung Cheng <ycheng@google.com> Acked-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Eric Dumazet <edumazet@google.com> Link: https://lore.kernel.org/r/20220321165957.1769954-1-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When test_lirc_mode2_user exec failed, the test report failed but still
exit with 0. Fix it by exiting with an error code.
Another issue is for the LIRCDEV checking. With bash -n, we need to quote
the variable, or it will always be true. So if test_lirc_mode2_user was
not run, just exit with skip code.
Fixes: 6bdd533cee9a ("bpf: add selftest for lirc_mode2 type program") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/bpf/20220321024149.157861-1-liuhangbin@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Attempting to rollback the activation of the current master when
the current master has not been activated is bad. priv->cur_chan
and priv->cur_adap are both still zeroed out and the rollback
may result in attempts to revert an of changeset that has not been
applied and do result in calls to both del and put the zeroed out
i2c_adapter. Maybe it crashes, or whatever, but it's bad in any
case.
Fixes: e9d1a0a41d44 ("i2c: mux: demux-pinctrl: Fix an error handling path in 'i2c_demux_pinctrl_probe()'") Signed-off-by: Peter Rosin <peda@axentia.se> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When a netlink message is received, netlink_recvmsg() fills in the address
of the sender. One of the fields is the 32-bit bitfield nl_groups, which
carries the multicast group on which the message was received. The least
significant bit corresponds to group 1, and therefore the highest group
that the field can represent is 32. Above that, the UB sanitizer flags the
out-of-bounds shift attempts.
Which bits end up being set in such case is implementation defined, but
it's either going to be a wrong non-zero value, or zero, which is at least
not misleading. Make the latter choice deterministic by always setting to 0
for higher-numbered multicast groups.
To get information about membership in groups >= 32, userspace is expected
to use nl_pktinfo control messages[0], which are enabled by NETLINK_PKTINFO
socket option.
[0] https://lwn.net/Articles/147608/
The way to trigger this issue is e.g. through monitoring the BRVLAN group:
# bridge monitor vlan &
# ip link add name br type bridge
Which produces the following citation:
UBSAN: shift-out-of-bounds in net/netlink/af_netlink.c:162:19
shift exponent 32 is too large for 32-bit type 'int'
Fixes: f7fa9b10edbb ("[NETLINK]: Support dynamic number of multicast groups per netlink family") Signed-off-by: Petr Machata <petrm@nvidia.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Link: https://lore.kernel.org/r/2bef6aabf201d1fc16cca139a744700cff9dcb04.1647527635.git.petrm@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
That happened because hdev->power_on is already called before
sdio_set_drvdata which btmtksdio_interrupt handler relies on is not
properly set up.
The details are shown as the below: hci_register_dev would run
queue_work(hdev->req_workqueue, &hdev->power_on) as WQ_HIGHPRI
workqueue_struct to complete the power-on sequeunce and thus hci_power_on
may run before sdio_set_drvdata is done in btmtksdio_probe.
The hci_dev_do_open in hci_power_on would initialize the device and enable
the interrupt and thus it is possible that btmtksdio_interrupt is being
called right before sdio_set_drvdata is filled out.
When btmtksdio_interrupt is being called and sdio_set_drvdata is not filled
, the kernel oops is going to happen because btmtksdio_interrupt access an
uninitialized pointer.
Fixes: 9aebfd4a2200 ("Bluetooth: mediatek: add support for MediaTek MT7663S and MT7668S SDIO devices") Reviewed-by: Mark Chen <markyawenchen@gmail.com> Co-developed-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Yake Yang <yake.yang@mediatek.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The rts51x_read_mem() function should return negative error codes.
Currently if the kmalloc() fails it returns USB_STOR_TRANSPORT_ERROR (3)
which is treated as success by the callers.
Fixes: 065e60964e29 ("ums_realtek: do not use stack memory for DMA") Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Link: https://lore.kernel.org/r/20220304073504.GA26464@kili Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The mem of msg has been uncharged in tcp_bpf_send_verdict() by
sk_msg_return(), and would be uncharged by sk_msg_free() again. When psock
is null, we can simply returning an error code, this would then trigger
the sk_msg_free_nocharge in the error path of __SK_REDIRECT and would have
the side effect of throwing an error up to user space. This would be a
slight change in behavior from user side but would look the same as an
error if the redirect on the socket threw an error.
This issue can cause the following info:
WARNING: CPU: 0 PID: 2136 at net/ipv4/af_inet.c:155 inet_sock_destruct+0x13c/0x260
Call Trace:
<TASK>
__sk_destruct+0x24/0x1f0
sk_psock_destroy+0x19b/0x1c0
process_one_work+0x1b3/0x3c0
worker_thread+0x30/0x350
? process_one_work+0x3c0/0x3c0
kthread+0xe6/0x110
? kthread_complete_and_exit+0x20/0x20
ret_from_fork+0x22/0x30
</TASK>
Fixes: 604326b41a6f ("bpf, sockmap: convert to generic sk_msg interface") Signed-off-by: Wang Yufen <wangyufen@huawei.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: John Fastabend <john.fastabend@gmail.com> Link: https://lore.kernel.org/bpf/20220304081145.2037182-5-wangyufen@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
If tcp_bpf_sendmsg() is running while sk msg is full. When sk_msg_alloc()
returns -ENOMEM error, tcp_bpf_sendmsg() goes to wait_for_memory. If partial
memory has been alloced by sk_msg_alloc(), that is, msg_tx->sg.size is
greater than osize after sk_msg_alloc(), memleak occurs. To fix we use
sk_msg_trim() to release the allocated memory, then goto wait for memory.
Other call paths of sk_msg_alloc() have the similar issue, such as
tls_sw_sendmsg(), so handle sk_msg_trim logic inside sk_msg_alloc(),
as Cong Wang suggested.
This issue can cause the following info:
WARNING: CPU: 3 PID: 7950 at net/core/stream.c:208 sk_stream_kill_queues+0xd4/0x1a0
Call Trace:
<TASK>
inet_csk_destroy_sock+0x55/0x110
__tcp_close+0x279/0x470
tcp_close+0x1f/0x60
inet_release+0x3f/0x80
__sock_release+0x3d/0xb0
sock_close+0x11/0x20
__fput+0x92/0x250
task_work_run+0x6a/0xa0
do_exit+0x33b/0xb60
do_group_exit+0x2f/0xa0
get_signal+0xb6/0x950
arch_do_signal_or_restart+0xac/0x2a0
exit_to_user_mode_prepare+0xa9/0x200
syscall_exit_to_user_mode+0x12/0x30
do_syscall_64+0x46/0x80
entry_SYSCALL_64_after_hwframe+0x44/0xae
</TASK>
The reference counting issue happens in several error handling paths
on a refcounted object "nc->dmac". In these paths, the function simply
returns the error code, forgetting to balance the reference count of
"nc->dmac", increased earlier by dma_request_channel(), which may
cause refcount leaks.
Fix it by decrementing the refcount of specific object in those error
paths.
Fixes: f88fc122cc34 ("mtd: nand: Cleanup/rework the atmel_nand driver") Co-developed-by: Xiyu Yang <xiyuyang19@fudan.edu.cn> Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn> Co-developed-by: Xin Tan <tanxin.ctf@gmail.com> Signed-off-by: Xin Tan <tanxin.ctf@gmail.com> Signed-off-by: Xin Xiong <xiongx18@fudan.edu.cn> Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220304085330.3610-1-xiongx18@fudan.edu.cn Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
__setup() handlers should return 1 to obsolete_checksetup() in
init/main.c to indicate that the boot option has been handled.
A return of 0 causes the boot option/value to be listed as an Unknown
kernel parameter and added to init's (limited) argument or environment
strings. Also, error return codes don't mean anything to
obsolete_checksetup() -- only non-zero (usually 1) or zero.
So return 1 from setup_kmac().
Fixes: 9e21c7e40b7e ("MIPS: RB532: Replace parse_mac_addr() with mac_pton().") Fixes: 73b4390fb234 ("[MIPS] Routerboard 532: Support for base system") Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
From: Igor Zhbanov <i.zhbanov@omprussia.ru>
Link: lore.kernel.org/r/64644a2f-4a20-bab3-1e15-3b2cdd0defe3@omprussia.ru Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: linux-mips@vger.kernel.org Cc: "David S. Miller" <davem@davemloft.net> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Phil Sutter <n0-1@freewrt.org> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Daniel Walter <dwalter@google.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The vxcan driver provides a pair of virtual CAN interfaces to exchange
CAN traffic between different namespaces - analogue to veth.
In opposite to the vcan driver the local sent CAN traffic on this interface
is not echo'ed back but only sent to the remote peer. This is unusual and
can be easily fixed by removing IFF_ECHO from the netdevice flags that
are set for vxcan interfaces by default at startup.
Without IFF_ECHO set on driver level, the local sent CAN frames are echo'ed
in af_can.c in can_send(). This patch makes vxcan interfaces adopt the
same local echo behavior and procedures as known from the vcan interfaces.
Fixes: a8f820a380a2 ("can: add Virtual CAN Tunnel driver (vxcan)") Link: https://lore.kernel.org/all/20220309120416.83514-5-socketcan@hartkopp.net Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
mpc8xx_pic_init() should return -ENOMEM instead of 0 when
irq_domain_add_linear() return NULL. This cause mpc8xx_pics_init to continue
executing even if mpc8xx_pic_host is NULL.
Fixes: cc76404feaed ("powerpc/8xx: Fix possible device node reference leak") Signed-off-by: Hangyu Hua <hbh25y@gmail.com> Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20220223070223.26845-1-hbh25y@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
In test_lwt_ip_encap, the ingress IPv6 encap test failed from time to
time. The failure occured when an IPv4 ping through the IPv6 GRE
encapsulation did not receive a reply within the timeout. The IPv4 ping
and the IPv6 ping in the test used different timeouts (1 sec for IPv4
and 6 sec for IPv6), probably taking into account that IPv6 might need
longer to successfully complete. However, when IPv4 pings (with the
short timeout) are encapsulated into the IPv6 tunnel, the delays of IPv6
apply.
The actual reason for the long delays with IPv6 was that the IPv6
neighbor discovery sometimes did not complete in time. This was caused
by the outgoing interface only having a tentative link local address,
i.e., not having completed DAD for that lladdr. The ND was successfully
retried after 1 sec but that was too late for the ping timeout.
The IPv6 addresses for the test were already added with nodad. However,
for the lladdrs, DAD was still performed. We now disable DAD in the test
netns completely and just assume that the two lladdrs on each veth pair
do not collide. This removes all the delays for IPv6 traffic in the
test.
Without the delays, we can now also reduce the delay of the IPv6 ping to
1 sec. This makes the whole test complete faster because we don't need
to wait for the excessive timeout for each IPv6 ping that is supposed
to fail.
Fixes: 0fde56e4385b0 ("selftests: bpf: add test_lwt_ip_encap selftest") Signed-off-by: Felix Maurer <fmaurer@redhat.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/bpf/4987d549d48b4e316cd5b3936de69c8d4bc75a4f.1646305899.git.fmaurer@redhat.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
As the potential failure of the devm_request_threaded_irq(),
it should be better to check the return value of the
mc13xxx_irq_request() and return error if fails.
Fixes: 8e00593557c3 ("mfd: Add mc13892 support to mc13xxx") Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn> Signed-off-by: Lee Jones <lee.jones@linaro.org> Link: https://lore.kernel.org/r/20220224022331.3208275-1-jiasheng@iscas.ac.cn Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Include the DECstation interrupt handler in opting out of
FPU support.
Fixes a linker error:
mips-linux-ld: arch/mips/dec/int-handler.o: in function `fpu':
(.text+0x148): undefined reference to `handle_fpe_int'
Fixes: 183b40f992c8 ("MIPS: Allow FP support to be disabled") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Reported-by: kernel test robot <lkp@intel.com> Cc: Paul Burton <paulburton@kernel.org> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Maciej W. Rozycki <macro@orcam.me.uk> Cc: linux-mips@vger.kernel.org Acked-by: Maciej W. Rozycki <macro@orcam.me.uk> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
For hardware that only supports 32-bit writes to PCI there is the
possibility of clearing RW1C (write-one-to-clear) bits. A rate-limited
messages was introduced by fb2659230120, but rate-limiting is not the best
choice here. Some devices may not show the warnings they should if another
device has just produced a bunch of warnings. Also, the number of messages
can be a nuisance on devices which are otherwise working fine.
Change the ratelimit to a single warning per bus. This ensures no bus is
'starved' of emitting a warning and also that there isn't a continuous
stream of warnings. It would be preferable to have a warning per device,
but the pci_dev structure is not available here, and a lookup from devfn
would be far too slow.
Suggested-by: Bjorn Helgaas <helgaas@kernel.org> Fixes: fb2659230120 ("PCI: Warn on possible RW1C corruption for sub-32 bit config writes") Link: https://lore.kernel.org/r/20200806041455.11070-1-mark.tomlinson@alliedtelesis.co.nz Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Rob Herring <robh@kernel.org> Acked-by: Scott Branden <scott.branden@broadcom.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
As the potential failure of the wm8350_register_irq(),
it should be better to check it and return error if fails.
Also, use 'free_' in order to avoid same code.
Fixes: 14431aa0c5a4 ("power_supply: Add support for WM8350 PMU") Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn> Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
This driver is for an FPGA logic core, so there can be arbitrarily many
instances of the bus on a given system. Previously all of the I2C bus
names were "xiic-i2c" which caused issues with lm_sensors when trying to
map human-readable names to sensor inputs because it could not properly
distinguish the busses, for example. Append the platform device name to
the I2C bus name so it is unique between different instances.
Fixes: e1d5b6598cdc ("i2c: Add support for Xilinx XPS IIC Bus Interface") Signed-off-by: Robert Hancock <robert.hancock@calian.com> Tested-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Per Intel's SDM on the "Instruction Set Reference", when
loading segment descriptor, not-present segment check should
be after all type and privilege checks. But the emulator checks
it first, then #NP is triggered instead of #GP if privilege fails
and segment is not present. Put not-present segment check after
type and privilege checks in __load_segment_descriptor().
Fixes: 38ba30ba51a00 (KVM: x86 emulator: Emulate task switch in emulator.c) Reviewed-by: Sean Christopherson <seanjc@google.com> Signed-off-by: Hou Wenlong <houwenlong.hwl@antgroup.com>
Message-Id: <52573c01d369f506cadcf7233812427cf7db81a7.1644292363.git.houwenlong.hwl@antgroup.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
In emulation of writing to cr8, one of the lowest four bits in TPR[3:0]
is kept.
According to Intel SDM 10.8.6.1(baremetal scenario):
"APIC.TPR[bits 7:4] = CR8[bits 3:0], APIC.TPR[bits 3:0] = 0";
and SDM 28.3(use TPR shadow):
"MOV to CR8. The instruction stores bits 3:0 of its source operand into
bits 7:4 of VTPR; the remainder of VTPR (bits 3:0 and bits 31:8) are
cleared.";
and AMD's APM 16.6.4:
"Task Priority Sub-class (TPS)-Bits 3 : 0. The TPS field indicates the
current sub-priority to be used when arbitrating lowest-priority messages.
This field is written with zero when TPR is written using the architectural
CR8 register.";
so in KVM emulated scenario, clear TPR[3:0] to make a consistent behavior
as in other scenarios.
This doesn't impact evaluation and delivery of pending virtual interrupts
because processor does not use the processor-priority sub-class to
determine which interrupts to delivery and which to inhibit.
Sub-class is used by hardware to arbitrate lowest priority interrupts,
but KVM just does a round-robin style delivery.
Fixes: b93463aa59d6 ("KVM: Accelerated apic support") Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com> Reviewed-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20220210094506.20181-1-zhenzhong.duan@intel.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When CONFIG_GENERIC_CPU=y (true for all our defconfigs) we pass
-mcpu=powerpc64 to the compiler, even when we're building a 32-bit
kernel.
This happens because we have an ifdef CONFIG_PPC_BOOK3S_64/else block in
the Makefile that was written before 32-bit supported GENERIC_CPU. Prior
to that the else block only applied to 64-bit Book3E.
The GCC man page says -mcpu=powerpc64 "[specifies] a pure ... 64-bit big
endian PowerPC ... architecture machine [type], with an appropriate,
generic processor model assumed for scheduling purposes."
It's unclear how that interacts with -m32, which we are also passing,
although obviously -m32 is taking precedence in some sense, as the
32-bit kernel only contains 32-bit instructions.
This was noticed by inspection, not via any bug reports, but it does
affect code generation. Comparing before/after code generation, there
are some changes to instruction scheduling, and the after case (with
-mcpu=powerpc64 removed) the compiler seems more keen to use r8.
Fix it by making the else case only apply to Book3E 64, which excludes
32-bit.
Fixes: 0e00a8c9fd92 ("powerpc: Allow CPU selection also on PPC32") Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20220215112858.304779-1-mpe@ellerman.id.au Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Currently if a declaration appears in the BTF before the definition, the
definition is dumped as a conflicting name, e.g.:
$ bpftool btf dump file vmlinux format raw | grep "'unix_sock'"
[81287] FWD 'unix_sock' fwd_kind=struct
[89336] STRUCT 'unix_sock' size=1024 vlen=14
$ bpftool btf dump file vmlinux format c | grep "struct unix_sock"
struct unix_sock;
struct unix_sock___2 { <--- conflict, the "___2" is unexpected
struct unix_sock___2 *unix_sk;
This causes a compilation error if the dump output is used as a header file.
Fix it by skipping declaration when counting duplicated type names.
Fixes: 351131b51c7a ("libbpf: add btf_dump API for BTF-to-C conversion") Signed-off-by: Xu Kuohai <xukuohai@huawei.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Song Liu <songliubraving@fb.com> Link: https://lore.kernel.org/bpf/20220301053250.1464204-2-xukuohai@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
insn_to_jit_off passed to bpf_prog_fill_jited_linfo() is calculated in
instruction granularity instead of bytes granularity, but BPF line info
requires byte offset.
bpf_prog_fill_jited_linfo() will be the last user of ctx.offset before
it is freed, so convert the offset into byte-offset before calling into
bpf_prog_fill_jited_linfo() in order to fix the line info dump on arm64.
Fixes: 37ab566c178d ("bpf: arm64: Enable arm64 jit to provide bpf_line_info") Suggested-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Hou Tao <houtao1@huawei.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/bpf/20220226121906.5709-3-houtao1@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
BPF line info needs ctx->offset to be the instruction offset in the whole JITed
image instead of the body itself, so also call build_prologue() first in first
JIT pass.
Fixes: 37ab566c178d ("bpf: arm64: Enable arm64 jit to provide bpf_line_info") Signed-off-by: Hou Tao <houtao1@huawei.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/bpf/20220226121906.5709-2-houtao1@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Currently the permission of parameter prot_mask is 0x0, which means that
the member does not appear in sysfs. Change it as other module parameters
to 0444 for world-readable.
[mkp: s/v3/v2/]
Link: https://lore.kernel.org/r/1645703489-87194-2-git-send-email-john.garry@huawei.com Fixes: d6a9000b81be ("scsi: hisi_sas: Add support for DIF feature for v2 hw") Reported-by: Yihang Li <liyihang6@hisilicon.com> Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com> Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
projects / mirror_ubuntu-focal-kernel.git / log