load is an unsigned integer. So, it is always bigger or equal
to zero, as reported by gcc:
drivers/media/i2c/max2175.c: In function 'max2175_refout_load_to_bits':
drivers/media/i2c/max2175.c:1272:11: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
if (load >= 0 && load <= 40)
^~
[media] media: platform: rcar_drif: Add DRIF support
This patch adds Digital Radio Interface (DRIF) support to R-Car Gen3 SoCs.
The driver exposes each instance of DRIF as a V4L2 SDR device. A DRIF
device represents a channel and each channel can have one or two
sub-channels respectively depending on the target board.
DRIF supports only Rx functionality. It receives samples from a RF
frontend tuner chip it is interfaced with. The combination of DRIF and the
tuner device, which is registered as a sub-device, determines the receive
sample rate and format.
In order to be compliant as a V4L2 SDR device, DRIF needs to bind with
the tuner device, which can be provided by a third party vendor. DRIF acts
as a slave device and the tuner device acts as a master transmitting the
samples. The driver allows asynchronous binding of a tuner device that
is registered as a v4l2 sub-device. The driver can learn about the tuner
it is interfaced with based on port endpoint properties of the device in
device tree. The V4L2 SDR device inherits the controls exposed by the
tuner device.
The device can also be configured to use either one or both of the data
pins at runtime based on the master (tuner) configuration.
[media] media: Add new SDR formats PC16, PC18 & PC20
This patch adds support for the three new SDR formats. These formats
were prefixed with "planar" indicating I & Q data are not interleaved
as in other formats. Here, I & Q data constitutes the top half and bottom
half of the received buffer respectively.
This patch adds driver support for the MAX2175 chip. This is Maxim
Integrated's RF to Bits tuner front end chip designed for software-defined
radio solutions. This driver exposes the tuner as a sub-device instance
with standard and custom controls to configure the device.
Hans Verkuil [Wed, 7 Jun 2017 14:46:12 +0000 (11:46 -0300)]
[media] cec: add CEC_CAP_NEEDS_HPD
Add a new capability CEC_CAP_NEEDS_HPD. If this capability is set
then the hardware can only use CEC if the HDMI Hotplug Detect pin
is high. Such hardware cannot handle the corner case in the CEC specification
where it is possible to transmit messages even if no hotplug signal is
present (needed for some displays that turn off the HPD when in standby,
but still have CEC enabled).
Typically hardware that needs this capability have the HPD wired to the CEC
block, often to a 'power' or 'active' pin.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Hans Verkuil [Wed, 7 Jun 2017 14:46:10 +0000 (11:46 -0300)]
[media] cec: add cec_transmit_attempt_done helper function
A simpler variant of cec_transmit_done to be used where the HW does
just a single attempt at a transmit. So if the status indicates an
error, then the corresponding error count will always be 1 and this
function figures that out based on the status argument.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
[media] s5k6aa: set usleep_range() range greater than 0
As this is not in atomic context and it does not seem like a critical
timing setting a range of 1ms allows the timer subsystem to optimize
the hrtimer here.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org> Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
[media] exynos-gsc: Use user configured colorspace if provided
Use colorspace provided by the user as we are only doing scaling and
color encoding conversion, we won't be able to transform the colorspace
itself and the colorspace won't mater in that operation.
Also always use output colorspace on the capture side.
If the user does not provide a colorspace do not make it up, we might
later while processing need to figure out the colorspace, which
is possible depending on the frame size but do not ever guess and
leak that guess to the userspace.
Trivial fix to spelling mistake in mfc_err error messages
Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
v4l2_m2m_job_finish(), which is called from the interrupt handler with
slock acquired, can call the device_run() hook immediately if another
context was in the queue. This hook also acquires slock, resulting in
a deadlock for this scenario.
Fix this by releasing slock right before calling v4l2_m2m_job_finish().
This is safe to do as the state of the hardware cannot change before
v4l2_m2m_job_finish() is called anyway.
David Härdeman [Thu, 27 Apr 2017 20:34:08 +0000 (17:34 -0300)]
[media] rc-core: cleanup rc_register_device pt2
Now that rc_register_device() is reorganised, the dev->initialized
hack can be removed. Any driver which calls rc_register_device()
must be prepared for the device to go live immediately.
The dev->initialized commits that are relevant are commit c73bbaa4ec3e
("[media] rc-core: don't lock device at rc_register_device()") and
commit 08aeb7c9a42a ("[media] rc: add locking to fix register/show race").
The original problem was that show_protocols() would access
dev->rc_map.* and various other bits which are now properly
initialized before device_add() is called.
At the same time, remove the bogus "device is being removed" check.
Signed-off-by: David Härdeman <david@hardeman.nu> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
David Härdeman [Wed, 3 May 2017 10:04:00 +0000 (07:04 -0300)]
[media] rc-core: cleanup rc_register_device
The device core infrastructure is based on the presumption that
once a driver calls device_add(), it must be ready to accept
userspace interaction.
This requires splitting rc_setup_rx_device() into two functions
and reorganizing rc_register_device() so that as much work
as possible is performed before calling device_add().
Signed-off-by: David Härdeman <david@hardeman.nu> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This module was merged after commit 5a8fc6a3cebb ("Annotate hardware
config module parameters in drivers/media/"), so add add the missing
hardware annotations.
Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch add cec driver for STM32 platforms.
cec hardware block isn't not always used with hdmi so
cec notifier is not implemented. That will be done later
when STM32 DSI driver will be available.
Driver compliance has been tested with cec-ctl and cec-compliance
tools.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org> Signed-off-by: Yannick Fertre <yannick.fertre@st.com>
[hans.verkuil@cisco.com: modified platform/Makefile to use obj-y] Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Kieran Bingham [Wed, 7 Jun 2017 09:52:07 +0000 (06:52 -0300)]
[media] v4l: subdev: tolerate null in media_entity_to_v4l2_subdev
Return NULL, if a null entity is parsed for it's v4l2_subdev
Currently, the callers of media_entity_to_v4l2_subdev() need to
make sure that the subdev is non-NULL, for example, when it is
obtained from media_entity_remote_pad().
As this is a recurring pattern, add the check at the macro in order
to avoid additional checks at the callers.
Sakari Ailus [Wed, 31 May 2017 14:17:25 +0000 (11:17 -0300)]
[media] vb2: Rename confusingly named internal buffer preparation functions
Rename __qbuf_*() functions which are specific to a buffer type as
__prepare_*() which matches with what they do. The naming was there for
historical reasons; the purpose of the functions was changed without
renaming them.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Sakari Ailus [Fri, 26 May 2017 13:00:48 +0000 (10:00 -0300)]
[media] ad5820: unregister async sub-device
The async sub-device was not unregistered in ad5820_remove() as it should
have been; do it now. Also remove the now-redundant
v4l2_device_unregister_subdev().
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Acked-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Colin Ian King [Sun, 7 May 2017 18:33:05 +0000 (15:33 -0300)]
[media] pvrusb2: remove redundant check on cnt > 8
The 2nd check of cnt > 8 is redundant as cnt is already checked
and thresholded to a maximum of 8 a few statements earlier.
Remove this redundant 2nd check.
Detected by CoverityScan, CID#114281 ("Logically dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Hans de Goede [Fri, 2 Jun 2017 20:04:23 +0000 (17:04 -0300)]
[media] staging: atomisp: Fix endless recursion in hmm_init
hmm_init calls hmm_alloc to set dummy_ptr, hmm_alloc calls
hmm_init when dummy_ptr is not yet set, which is the case in
the call from hmm_init, so it calls hmm_init again, this continues
until we have a stack overflow due to the recursion.
This commit fixes this by adding a separate flag for tracking if
hmm_init has been called. Not pretty, but it gets the job done,
eventually we should be able to remove the hmm_init call from
hmm_alloc.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Hans de Goede [Sun, 28 May 2017 12:31:53 +0000 (09:31 -0300)]
[media] staging: atomisp: Make ov2680 driver less chatty
There is no reason for all this printk spamming and certainly
not at an error log level.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Hans de Goede [Sun, 28 May 2017 12:31:52 +0000 (09:31 -0300)]
[media] staging: atomisp: Ignore errors from second gpio in ov2680 driver
As the existing comment in the driver indicates the sensor has only 1 pin,
but some boards may have 2 gpios defined and we toggle both as we we don't
know which one is the right one. However if the ACPI resources table
defines only 1 gpio (as expected) the gpio1_ctrl call will always fail,
causing the probing of the driver to file.
This commit ignore the return value of the gpio1_ctrl call, fixing this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Hans de Goede [Sun, 28 May 2017 12:31:51 +0000 (09:31 -0300)]
[media] staging: atomisp: Add OVTI2680 ACPI id to ov2680 driver
Add OVTI2680 ACPI id to ov2680 driver
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Hans de Goede [Sun, 28 May 2017 12:31:50 +0000 (09:31 -0300)]
[media] staging: atomisp: Add INT0310 ACPI id to gc0310 driver
Add INT0310 ACPI id to gc0310 driver
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Hans de Goede [Sun, 28 May 2017 12:31:49 +0000 (09:31 -0300)]
[media] staging: atomisp: Set step to 0 for mt9m114 menu control
menu controls are not allowed to have a step size, set step to 0 to
fix an oops from the WARN_ON in v4l2_ctrl_new_custom() triggering
because of this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Hans de Goede [Sun, 28 May 2017 12:31:48 +0000 (09:31 -0300)]
[media] staging: atomisp: Do not call dev_warn with a NULL device
Do not call dev_warn with a NULL device, this silence the following 2
warnings:
[ 14.392194] (NULL device *): Failed to find gmin variable gmin_V2P8GPIO
[ 14.392257] (NULL device *): Failed to find gmin variable gmin_V1P8GPIO
We could switch to using pr_warn for dev == NULL instead, but as comments
in the source indicate, the check for these 2 special gmin variables with
a NULL device is a workaround for 2 specific evaluation boards, so
completely silencing the missing warning for these actually is a good
thing.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Hans de Goede [Sun, 28 May 2017 12:31:47 +0000 (09:31 -0300)]
[media] staging: atomisp: Fix calling efivar_entry_get() with unaligned arguments
efivar_entry_get has certain alignment requirements and the atomisp
platform code was not honoring these, causing an oops by triggering the
WARN_ON in arch/x86/platform/efi/efi_64.c: virt_to_phys_or_null_size().
This commit fixes this by using the members of the efivar struct embedded
in the efivar_entry struct we kzalloc as arguments to efivar_entry_get(),
which is how all the other callers of efivar_entry_get() do this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Between the ISP2400 and ISP2401 code base this function moved file. The merge
of the drivers left us with two version in ifdefs. Resolve this down to a
single copy.
Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Alan Cox [Fri, 26 May 2017 15:29:15 +0000 (12:29 -0300)]
[media] atomisp: Unify load_preview_binaries for the most part
ISP2401 introduced a rather sensible change to cut through the structure
spaghetti. Adopt that for the ISP2400 as well. It makes no difference to the
actual code other than readability.
Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The ISP2401 version of this function returns a pointer to the buffer, whilst
the ISP2400 version returns a boolean if a slot is found. We can trivially
unify the code to use the ISP2401 version.
Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Dan Carpenter [Fri, 26 May 2017 15:28:05 +0000 (12:28 -0300)]
[media] atomisp2: off by one in atomisp_s_input()
The isp->inputs[] array has isp->input_cnt elements which have been
initialized so this > should be >=.
This bug is harmless. The check against ATOM_ISP_MAX_INPUTS prevents us
from reading beyond the end of the array. The uninitialized elements
are zeroed out so we will end up returning -EINVAL a few lines later
because the .camera pointer is NULL.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
[media] staging: media: atomisp: fix non static symbol warnings
Fix a couple of sparse warnings:
drivers/staging/media/atomisp/pci/atomisp2/atomisp_v4l2.c:59:14: warning: symbol 'repool_pgnr' was not declared. Should it be static?
drivers/staging/media/atomisp/pci/atomisp2/atomisp_v4l2.c:387:6: warning: symbol 'punit_ddr_dvfs_enable' was not declared. Should it be static?
Mark these symbols as static, so they are no longer incorrectly exported.
Signed-off-by: Juan Antonio Pedreira Martos <juanpm1@gmail.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Daniel Kurtz [Tue, 23 May 2017 03:24:11 +0000 (00:24 -0300)]
[media] media: mtk-mdp: Fix mdp device tree
If the mdp_* nodes are under an mdp sub-node, their corresponding
platform device does not automatically get its iommu assigned properly.
Fix this by moving the mdp component nodes up a level such that they are
siblings of mdp and all other SoC subsystems. This also simplifies the
device tree.
Although it fixes iommu assignment issue, it also break compatibility
with old device tree. So, the patch in driver is needed to iterate over
sibling mdp device nodes, not child ones, to keep driver work properly.
Minghsiu Tsai [Tue, 23 May 2017 03:24:09 +0000 (00:24 -0300)]
[media] dt-bindings: mt8173: Fix mdp device tree
If the mdp_* nodes are under an mdp sub-node, their corresponding
platform device does not automatically get its iommu assigned properly.
Fix this by moving the mdp component nodes up a level such that they are
siblings of mdp and all other SoC subsystems. This also simplifies the
device tree.
Although it fixes iommu assignment issue, it also break compatibility
with old device tree. So, the patch in driver is needed to iterate over
sibling mdp device nodes, not child ones, to keep driver work properly.
Signed-off-by: Minghsiu Tsai <minghsiu.tsai@mediatek.com> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Philipp Zabel [Tue, 6 Jun 2017 15:59:02 +0000 (12:59 -0300)]
[media] coda: copy headers in front of every I-frame
That way we don't have to rely on userspace to inject the headers on IDR
requests, and there is always enough information to start decoding at an
I-frame.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Philipp Zabel [Tue, 6 Jun 2017 15:59:01 +0000 (12:59 -0300)]
[media] coda: implement forced key frames
Implement the V4L2_CID_MPEG_VIDEO_FORCE_KEY_FRAME control to force IDR
frames. This is useful to implement VFU (Video Fast Update) on RTP
transmissions.
We already force an IDR frame at the beginning of each GOP to work
around a firmware bug on i.MX27, use the same mechanism to service IDR
requests from userspace.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Jia-Ju Bai [Thu, 1 Jun 2017 07:17:51 +0000 (04:17 -0300)]
[media] cx18: Fix a sleep-in-atomic bug in snd_cx18_pcm_hw_free
The driver may sleep under a spin lock, and the function call path is:
snd_cx18_pcm_hw_free (acquire the lock by spin_lock_irqsave)
vfree --> may sleep
To fix it, the "substream->runtime->dma_area" is passed to a temporary
value, and mark it NULL when holding the lock. The memory is freed by
vfree through the temporary value outside the lock holding.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
[hans.verkuil@cisco.com: removed unnecessary 'if (dma_area)'] Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Jia-Ju Bai [Thu, 1 Jun 2017 07:13:54 +0000 (04:13 -0300)]
[media] ivtv: Fix a sleep-in-atomic bug in snd_ivtv_pcm_hw_free
The driver may sleep under a spin lock, and the function call path is:
snd_ivtv_pcm_hw_free (acquire the lock by spin_lock_irqsave)
vfree --> may sleep
To fix it, the "substream->runtime->dma_area" is passed to a temporary
value, and mark it NULL when holding the lock. The memory is freed by
vfree through the temporary value outside the lock holding.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
[hans.verkuil@cisco.com: removed unnecessary 'if (dma_area)'] Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Kevin Hilman [Tue, 6 Jun 2017 23:37:40 +0000 (20:37 -0300)]
[media] davinci: vpif_capture: cleanup raw camera support
The current driver has a handful of hard-coded assumptions based on its
primary use for capture of video signals. Cleanup those assumptions,
and also query the subdev for format information and use that if
available.
Tested with 10-bit raw bayer input (SGRBG10) using the aptina,mt9v032
sensor, and also tested that composite video input still works from
ti,tvp514x decoder. Both tests done on the da850-evm board with the
add-on UI board.
NOTE: Will need further testing for other sensors with different bus
formats.
Signed-off-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Kevin Hilman [Tue, 6 Jun 2017 23:37:38 +0000 (20:37 -0300)]
[media] davinci: vpif_capture: drop compliance hack
Capture driver silently overrides pixel format with a hack (according to
the comments) to pass v4l2 compliance tests. This isn't needed for
normal functionality, and works for composite video and raw camera capture
without.
In addition, the hack assumes that it only supports raw capture with a
single format (SBGGR8) which isn't true. VPIF can also capture 10- and
12-bit raw formats as well. Forthcoming patches will enable VPIF
input with raw-camera support and has been tested with 10-bit format
from the aptina,mt9v032 sensor.
Any compliance failures should be fixed with a real fix.
Signed-off-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Anton Blanchard [Sun, 7 May 2017 01:00:11 +0000 (22:00 -0300)]
[media] ir-spi: Fix issues with lirc API
The ir-spi driver has 2 issues which prevents it from working with
lirc:
1. The ir-spi driver uses 16 bits of SPI data to create one cycle of
the waveform. As such our SPI clock needs to be 16x faster than the
carrier frequency.
The driver is inconsistent in how it currently handles this. It
initializes it to the carrier frequency:
But the commit message has some example code which initialises it
to 16x the carrier frequency:
val = 608000;
ret = ioctl(fd, LIRC_SET_SEND_CARRIER, &val);
To maintain compatibility with lirc, always do the frequency adjustment
in the driver.
2. lirc presents pulses in microseconds, but the ir-spi driver treats
them as cycles of the carrier. Similar to other lirc drivers, do the
conversion with DIV_ROUND_CLOSEST().
Fixes: fe052da49201 ("[media] rc: add support for IR LEDs driven through SPI") Cc: stable@vger.kernel.org Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Johan Hovold [Thu, 1 Jun 2017 07:46:00 +0000 (04:46 -0300)]
[media] mceusb: drop redundant urb reinitialisation
Drop a since commit e1159cb35712 ("[media] mceusb: remove pointless
mce_flush_rx_buffer function") redundant reinitialisation of two urb
fields immediately after they have been initialised.
Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Dave Stevenson [Fri, 2 Jun 2017 12:18:14 +0000 (09:18 -0300)]
[media] tc358743: Add support for platforms without IRQ line
interrupts is listed as an optional property in the DT
binding, but in reality the driver didn't work without it.
The existing driver relied on having the interrupt line
connected to the SoC to trigger handling various events.
Add the option to poll the interrupt status register via
a timer if no interrupt source is defined.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Dave Stevenson [Fri, 2 Jun 2017 12:18:13 +0000 (09:18 -0300)]
[media] tc358743: Setup default mbus_fmt before registering
Previously the mbus_fmt_code was set after the device was
registered. If a connected sub-device called tc358743_get_fmt
prior to that point it would get an invalid code back.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Hans Verkuil [Wed, 31 May 2017 09:50:26 +0000 (06:50 -0300)]
[media] cec: improve debug messages
- use __func__ instead of writing the full function name
- drop debug message in cec_config_log_addr since the same information
will be reported later
- use debug level 1 for errors and infrequent events, use level 2 for
debugging CEC message traffic
- log when a transmit is retried, very useful to know when debugging
- debug messages now all start with lower case
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Sakari Ailus [Fri, 26 May 2017 08:21:37 +0000 (05:21 -0300)]
[media] v4l2-ctrls.c: Implement unlocked variant of v4l2_ctrl_handler_setup()
Sometimes the caller is already holding the control handler mutex and
using it to serialise something. Provide an unlocked variant of the same
function to be used in those cases.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Hugues Fruchet [Fri, 19 May 2017 10:04:52 +0000 (07:04 -0300)]
[media] atmel-isi: code cleanup
Ensure that ISI is clocked before starting sensor sub device.
Remove un-needed type check in try_fmt().
Use clamp() macro for hardware capabilities.
Fix wrong tabulation to space.
* tag 'media/v4.12-2': (598 commits)
[media] rc-core: race condition during ir_raw_event_register()
[media] cec: drop MEDIA_CEC_DEBUG
[media] cec: rename MEDIA_CEC_NOTIFIER to CEC_NOTIFIER
[media] cec: select CEC_CORE instead of depend on it
[media] rainshadow-cec: ensure exit_loop is intialized
[media] atomisp: don't treat warnings as errors
Linux 4.12-rc3
x86/ftrace: Make sure that ftrace trampolines are not RWX
x86/mm/ftrace: Do not bug in early boot on irqs_disabled in cpu_flush_range()
selftests/ftrace: Add a testcase for many kprobe events
kprobes/x86: Fix to set RWX bits correctly before releasing trampoline
ftrace: Fix memory leak in ftrace_graph_release()
ipv4: add reference counting to metrics
net: ethernet: ax88796: don't call free_irq without request_irq first
ip6_tunnel, ip6_gre: fix setting of DSCP on encapsulated packets
sctp: fix ICMP processing if skb is non-linear
net: llc: add lock_sock in llc_ui_bind to avoid a race condition
PCI/msi: fix the pci_alloc_irq_vectors_affinity stub
blk-mq: Only register debugfs attributes for blk-mq queues
x86/timers: Move simple_udelay_calibration past init_hypervisor_platform
...
Nori, Sekhar [Fri, 26 May 2017 10:55:27 +0000 (07:55 -0300)]
[media] davinci: vpif_capture: fix default pixel format for BT.656/BT.1120 video
For both BT.656 and BT.1120 video, the pixel format
used by VPIF is Y/CbCr 4:2:2 in semi-planar format
(Luma in one plane and Chroma in another). This
corresponds to NV16 pixel format.
This is documented in section 36.2.3 of OMAP-L138
Technical Reference Manual, SPRUH77A.
The VPIF driver incorrectly sets the default format
to V4L2_PIX_FMT_YUV422P. Fix it.
Reported-by: Alejandro Hernandez <ajhernandez@ti.com> Signed-off-by: Sekhar Nori <nsekhar@ti.com> Acked-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Philipp Zabel [Mon, 22 May 2017 16:34:48 +0000 (13:34 -0300)]
[media] coda: improve colorimetry handling
The hardware codec is not colorspace aware. We should trust userspace to
set the correct colorimetry information on the OUTPUT queue and mirror
the exact same setting on the CAPTURE queue.
There is no reason to restrict colorspace to JPEG or REC709 only. Also,
set the default colorspace, as returned by calling VIDIOC_TRY/S_FMT with
V4L2_COLORSPACE_DEFAULT, initially.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Niklas Söderlund [Wed, 24 May 2017 00:15:37 +0000 (21:15 -0300)]
[media] rcar-vin: remove subdevice matching from bind and unbind callbacks
There is only one subdevice registered with the async framework so there
is no need for the driver to check which subdevice is bound or unbound.
Remove these checks since the async framework preforms this.