For all these, the changes mostly consititude additions of DT
contents, but also some Kconfig entries to allow dependency/selection
of drivers per-platform, etc"
* tag '64bit-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arm64: Kconfig: clean up two no-op Kconfig options from CONFIG_ARCH_TEGRA*
arm64: Fix sort of platform Kconfig entries
arm64: Add support for FSL's LS2085A SoC in Kconfig and defconfig
arm64: Add DTS support for FSL's LS2085A SoC
arm64: mediatek: Add MT8173 SoC Kconfig and defconfig
arm64: dts: Add mediatek MT8173 SoC and evaluation board dts and Makefile
Document: DT: Add bindings for mediatek MT8173 SoC Platform
arm64: Add Tegra132 support
arm64: Enable ARMv8 based exynos7 SoC support
arm64: dts: Add nodes for mmc, i2c, rtc, watchdog, adc on exynos7
arm64: dts: Add PMU DT node for exynos7 SoC
arm64: dts: Add initial pinctrl support to exynos7
arm64: dts: Add initial device tree support for exynos7
Linus Torvalds [Tue, 17 Feb 2015 17:44:50 +0000 (09:44 -0800)]
Merge tag 'defconfig-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC defconfig changes from Olof Johansson:
"Most of these changes are to enable new drivers that have been merged,
or various additions to make defconfigs more useful. There's also a
set of patches trimming down omap2plus kernel size a bit since it is
quite large"
* tag 'defconfig-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (39 commits)
ARM: config: add DEVTMPFS option by default to keystone config
ARM: multi_v7_defconfig: Enable Exynos5420 Multi-Cluster PM support
ARM: shmobile: Select CONFIG_REGULATOR in defconfig once again
ARM: exynos_defconfig: Enable CONFIG_FHANDLE
ARM: exynos_defconfig: Enable PMIC and MUIC drivers for Gears and Trats2
ARM: exynos_defconfig: Enable CONFIG_LOCKUP_DETECTOR
ARM: config: enable ARCH_HIP01
ARM: omap2plus_defconfig: Enable OHCI & EHCI HCD support
ARM: omap2plus_defconfig: Enable misc options for BeagleBoard-X15 platform
ARM: imx_v6_v7_defconfig: enable more USB functions
ARM: imx_v6_v7_defconfig: Select CONFIG_FB_MXS
ARM: omap2plus_defconfig: Enable pcf857x
ARM: omap2plus_defconfig: Add NOR flash support
ARM: omap2plus_defconfig: Enable support for davinci_emac
ARM: multi_v7_defconfig: Enable MiPHY28lp - ST's Generic (SATA, PCIe & USB3) PHY
ARM: efm32: update defconfig
ARM: at91: sama5: enable atmel-isi and ov2640 in defconfig
ARM: multi_v7_defconfig: Enable Hip01 platform
ARM: config: multi_v7: Update it for Keystone defconfig
ARM: shmobile: Enable kzm9g board in multiplatform defconfig
...
Linus Torvalds [Tue, 17 Feb 2015 17:38:59 +0000 (09:38 -0800)]
Merge tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"These are changes for drivers that are intimately tied to some SoC and
for some reason could not get merged through the respective subsystem
maintainer tree.
This time around, much of this is for at91, with the bulk of it being
syscon and udc drivers.
Also, there's:
- coupled cpuidle support for Samsung Exynos4210
- Renesas 73A0 common-clk work
- of/platform changes to tear down DMA mappings on device destruction
- a few updates to the TI Keystone knav code"
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (26 commits)
cpuidle: exynos: add coupled cpuidle support for exynos4210
ARM: EXYNOS: apply S5P_CENTRAL_SEQ_OPTION fix only when necessary
soc: ti: knav_qmss_queue: change knav_range_setup_acc_irq to static
soc: ti: knav_qmss_queue: makefile tweak to build as dynamic module
pcmcia: at91_cf: depend on !ARCH_MULTIPLATFORM
soc: ti: knav_qmss_queue: export API calls for use by user driver
of/platform: teardown DMA mappings on device destruction
usb: gadget: at91_udc: Allocate udc instance
usb: gadget: at91_udc: Update DT binding documentation
usb: gadget: at91_udc: Rework for multi-platform kernel support
usb: gadget: at91_udc: Simplify probe and remove functions
usb: gadget: at91_udc: Remove non-DT handling code
usb: gadget: at91_udc: Document DT clocks and clock-names property
usb: gadget: at91_udc: Drop uclk clock
usb: gadget: at91_udc: Fix clock names
mfd: syscon: Add Atmel SMC binding doc
mfd: syscon: Add atmel-smc registers definition
mfd: syscon: Add Atmel Matrix bus DT binding documentation
mfd: syscon: Add atmel-matrix registers definition
clk: shmobile: fix sparse NULL pointer warning
...
Linus Torvalds [Tue, 17 Feb 2015 17:36:52 +0000 (09:36 -0800)]
Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Olof Johansson:
"DT changes continue to be the bulk of our merge window contents.
We continue to have a large set of changes across the board as new
platforms and drivers are added.
Some of the new platforms are:
- Alphascale ASM9260
- Marvell Armada 388
- CSR Atlas7
- TI Davinci DM816x
- Hisilicon HiP01
- ST STiH418
There have also been some sweeping changes, including relicensing of
DTS contents from GPL to GPLv2+/X11 so that the same files can be
reused in other non-GPL projects more easily. There's also been
changes to the DT Makefile to make it a little less conflict-ridden
and churny down the road"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (330 commits)
ARM: dts: Add PPMU node for exynos4412-trats2
ARM: dts: Add PPMU node for exynos3250-monk and exynos3250-rinato
ARM: dts: Add PPMU dt node for exynos4 and exynos4210
ARM: dts: Add PPMU dt node for exynos3250
ARM: dts: add mipi dsi device node for exynos4415
ARM: dts: add fimd device node for exynos4415
ARM: dts: Add syscon phandle to the video-phy node for Exynos4
ARM: dts: Add sound nodes for exynos4412-trats2
ARM: dts: Fix CLK_MOUT_CAMn parent clocks assignment for exynos4412-trats2
ARM: dts: Fix CLK_UART_ISP_SCLK clock assignment in exynos4x12.dtsi
ARM: dts: Add max77693 charger node for exynos4412-trats2
ARM: dts: Switch max77686 regulators to GPIO control for exynos4412-trats2
ARM: dts: Add suspend configuration for max77686 regulators for exynos4412-trats2
ARM: dts: Add Maxim 77693 fuel gauge node for exynos4412-trats2
ARM: dts: am57xx-beagle-x15: Fix USB2 mode
ARM: dts: am57xx-beagle-x15: Add extcon nodes for USB
ARM: dts: dra72-evm: Add extcon nodes for USB
ARM: dts: dra7-evm: Add extcon nodes for USB
ARM: dts: rockchip: move the hdmi ddc-i2c-bus property to the actual boards
ARM: dts: rockchip: enable vops and hdmi output on rk3288-firefly and -evb
...
Linus Torvalds [Tue, 17 Feb 2015 17:27:54 +0000 (09:27 -0800)]
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Olof Johansson:
"New and updated SoC support. Also included are some cleanups where
the platform maintainers hadn't separated cleanups from new developent
in separate branches.
Some of the larger things worth pointing out:
- A large set of changes from Alexandre Belloni and Nicolas Ferre
preparing at91 platforms for multiplatform and cleaning up quite a
bit in the process.
- Removal of CSR's "Marco" SoC platform that never made it out to the
market. We love seeing these since it means the vendor published
support before product was out, which is exactly what we want!
New platforms this release are:
- Conexant Digicolor (CX92755 SoC)
- Hisilicon HiP01 SoC
- CSR/sirf Atlas7 SoC
- ST STiH418 SoC
- Common code changes for Nvidia Tegra132 (64-bit SoC)
We're seeing more and more platforms having a harder time labelling
changes as cleanups vs new development -- which is a good sign that
we've come quite far on the cleanup effort. So over time we might
start combining the cleanup and new-development branches more"
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (124 commits)
ARM: at91/trivial: unify functions and machine names
ARM: at91: remove at91_dt_initialize and machine init_early()
ARM: at91: change board files into SoC files
ARM: at91: remove at91_boot_soc
ARM: at91: move alternative initial mapping to board-dt-sama5.c
ARM: at91: merge all SOC_AT91SAM9xxx
ARM: at91: at91rm9200: set idle and restart from rm9200_dt_device_init()
ARM: digicolor: select syscon and timer
ARM: zynq: Simplify SLCR initialization
ARM: zynq: PM: Fixed simple typo.
ARM: zynq: Setup default gpio number for Xilinx Zynq
ARM: digicolor: add low level debug support
ARM: initial support for Conexant Digicolor CX92755 SoC
ARM: OMAP2+: Add dm816x hwmod support
ARM: OMAP2+: Add clock domain support for dm816x
ARM: OMAP2+: Add board-generic.c entry for ti81xx
ARM: at91: pm: remove warning to remove SOC_AT91SAM9263 usage
ARM: at91: remove unused mach/system_rev.h
ARM: at91: stop using HAVE_AT91_DBGUx
ARM: at91: fix ordering of SRAM and PM initialization
...
Linus Torvalds [Tue, 17 Feb 2015 17:17:33 +0000 (09:17 -0800)]
Merge tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This is a good healthy set of various code removals. Total net delta
is 8100 lines removed.
Among the larger cleanups are:
- Removal of old Samsung S3C DMA infrastructure by Arnd
- Removal of the non-DT version of the 'lager' board by Magnus Damm
- General stale code removal on OMAP and Davinci by Rickard Strandqvist
- Removal of non-DT support on am3517 platforms by Tony Lindgren
... plus several other cleanups of various platforms across the board"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (47 commits)
ARM: sirf: drop redundant function and marco declaration
arm: omap: specify PMUs are for ARMv7 CPUs
arm: shmobile: specify PMUs are for ARMv7 CPUs
arm: iop: specify PMUs are for XScale CPUs
arm: pxa: specify PMUs are for XScale CPUs
arm: realview: specify PMU types
ARM: SAMSUNG: remove unused DMA infrastructure
ARM: OMAP3: Add back Kconfig option MACH_OMAP3517EVM for ASoC
ARM: davinci: Remove CDCE949 driver
ARM: at91: remove useless at91rm9200_set_type()
ARM: at91: remove useless at91rm9200_dt_initialize()
ARM: at91: move debug-macro.S into the common space
ARM: at91: remove useless at91_sysirq_mask_rtx
ARM: at91: remove useless config MACH_AT91SAM9_DT
ARM: at91: remove useless config MACH_AT91RM9200_DT
ARM: at91: remove unused mach/memory.h
ARM: at91: remove useless header file includes
ARM: at91: remove unneeded header file
rtc: at91/Kconfig: remove useless options
ARM: at91/Documentation: add a README for Atmel SoCs
...
Linus Torvalds [Tue, 17 Feb 2015 17:15:46 +0000 (09:15 -0800)]
Merge tag 'fixes-non-critical-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC non-critical fixes from Olof Johansson:
"Here's a small collection of fixes accrued during the last release
that weren't considered severe enough to merge during the -rc series.
A few of these are around resurrecting TI81xx support that's been
broken for quite a while, the rest are smaller fixes -- most for PXA
but a few across the board.
There are also some updates to MAINTAINERS here, in particular for
Broadcom platforms"
* tag 'fixes-non-critical-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (23 commits)
MAINTAINERS: fix git repositories for Broadcom SoCs
ARM: pxa: fix broken isa interrupts for zeus and viper
ARM: DRA7: hwmod: Fix boot crash with DEBUG_LL enabled on UART3
ARM: OMAP: DRA7: hwmod: Make gpmc software supervised as the smart idle is broken
ARM: AM43xx: hwmod: set DSS submodule parent hwmods
ARM: OMAP2+: hwmod: print error if wait_target_ready() failed
MAINTAINERS: add maintainer for OMAP hwmod data
ARM: OMAP2+: Disable omap3 PM init for ti81xx
ARM: OMAP2+: Fix reboot for 81xx
ARM: OMAP2+: Fix dm814 and dm816 for clocks and timer init
ARM: OMAP2+: Fix ti81xx class type
ARM: OMAP2+: Fix ti81xx devtype
ARM: OMAP2+: Fix error handling for omap2_clk_enable_init_clocks
MAINTAINERS: add a git entry for BMIPS-based BCM7xxx SoCs
MAINTAINERS: add a git entry for BCM7xxx ARM-based SoCs
MAINTAINERS: update Broadcom Cygnus SoC git tree
MAINTAINERS: move BCM63xx ARM-based SoCs git tree
hx4700: regulator: declare full constraints
ARM: pxa: add regulator_has_full_constraints to spitz board file
ARM: pxa: add regulator_has_full_constraints to poodle board file
...
Linus Torvalds [Tue, 17 Feb 2015 16:38:30 +0000 (08:38 -0800)]
Merge branch 'akpm' (patches from Andrew)
Merge fifth set of updates from Andrew Morton:
- A few things which were awaiting merges from linux-next:
- rtc
- ocfs2
- misc others
- Willy's "dax" feature: direct fs access to memory (mainly NV-DIMMs)
which isn't backed by pageframes.
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (37 commits)
rtc: add driver for DS1685 family of real time clocks
MAINTAINERS: add entry for Maxim PMICs on Samsung boards
lib/Kconfig: use bool instead of boolean
powerpc: drop _PAGE_FILE and pte_file()-related helpers
ocfs2: set append dio as a ro compat feature
ocfs2: wait for orphan recovery first once append O_DIRECT write crash
ocfs2: complete the rest request through buffer io
ocfs2: do not fallback to buffer I/O write if appending
ocfs2: allocate blocks in ocfs2_direct_IO_get_blocks
ocfs2: implement ocfs2_direct_IO_write
ocfs2: add orphan recovery types in ocfs2_recover_orphans
ocfs2: add functions to add and remove inode in orphan dir
ocfs2: prepare some interfaces used in append direct io
MAINTAINERS: fix spelling mistake & remove trailing WS
dax: does not work correctly with virtual aliasing caches
brd: rename XIP to DAX
ext4: add DAX functionality
dax: add dax_zero_page_range
ext2: get rid of most mentions of XIP in ext2
ext2: remove ext2_aops_xip
...
Joshua Kinard [Tue, 17 Feb 2015 00:00:26 +0000 (16:00 -0800)]
rtc: add driver for DS1685 family of real time clocks
This adds a driver for the Dallas/Maxim DS1685-family of RTC chips. It
supports the DS1685/DS1687, DS1688/DS1691, DS1689/DS1693, DS17285/DS17287,
DS17485/DS17487, and DS17885/DS17887 RTC chips. These chips are commonly
found in SGI O2 and SGI Octane systems. It was originally derived from a
driver patch submitted by Matthias Fuchs many years ago for use in
EPPC-405-UC modules, which also used these RTCs. In addition to the
time-keeping functions, this RTC also handles the shutdown mechanism of
the O2 and Octane and acts as a partial NVRAM for the boot PROMS in these
systems.
MAINTAINERS: add entry for Maxim PMICs on Samsung boards
Add myself and Chanwoo Choi as supporters to help in reviewing patches
for Maxim 77686 PMIC and Maxim 14577/77693 MUIC drivers:
- mfd (all of them),
- extcon (extcon-max14577.c, extcon-max77693.c),
- regulator (all of them),
- clock (clk-max77686.c),
- RTC (rtc-max77686.c).
Lately I am the author of contributors to them. These drivers are used
on Exynos-based boards (Trats 2, Gear 1 and Gear 2).
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Cc: MyungJoo Ham <myungjoo.ham@samsung.com> Cc: Chanwoo Choi <cw00.choi@samsung.com> Cc: Samuel Ortiz <sameo@linux.intel.com> Cc: Lee Jones <lee.jones@linaro.org> Cc: Liam Girdwood <lgirdwood@gmail.com> Cc: Mark Brown <broonie@kernel.org> Cc: Mike Turquette <mturquette@linaro.org> Cc: Stephen Boyd <sboyd@codeaurora.org> Cc: Alessandro Zummo <a.zummo@towertech.it> Acked-by: Mark Brown <broonie@kernel.org> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Christoph Jaeger [Tue, 17 Feb 2015 00:00:20 +0000 (16:00 -0800)]
lib/Kconfig: use bool instead of boolean
Keyword 'boolean' for type definition attributes is considered
deprecated and, therefore, should not be used anymore.
See http://lkml.kernel.org/r/cover.1418003065.git.cj@linux.com
See http://lkml.kernel.org/r/1419108071-11607-1-git-send-email-cj@linux.com
Signed-off-by: Christoph Jaeger <cj@linux.com> Cc: Russell King <linux@arm.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joseph Qi [Tue, 17 Feb 2015 00:00:15 +0000 (16:00 -0800)]
ocfs2: set append dio as a ro compat feature
Intruduce a bit OCFS2_FEATURE_RO_COMPAT_APPEND_DIO and check it in
write flow. If the bit is not set, fall back to the old way.
Signed-off-by: Joseph Qi <joseph.qi@huawei.com> Cc: Weiwei Wang <wangww631@huawei.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Mark Fasheh <mfasheh@suse.com> Cc: Xuejiufei <xuejiufei@huawei.com> Cc: alex chen <alex.chen@huawei.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joseph Qi [Tue, 17 Feb 2015 00:00:12 +0000 (16:00 -0800)]
ocfs2: wait for orphan recovery first once append O_DIRECT write crash
If one node has crashed with orphan entry leftover, another node which do
append O_DIRECT write to the same file will override the
i_dio_orphaned_slot. Then the old entry won't be cleaned forever. If
this case happens, we let it wait for orphan recovery first.
Signed-off-by: Joseph Qi <joseph.qi@huawei.com> Cc: Weiwei Wang <wangww631@huawei.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Mark Fasheh <mfasheh@suse.com> Cc: Xuejiufei <xuejiufei@huawei.com> Cc: alex chen <alex.chen@huawei.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joseph Qi [Tue, 17 Feb 2015 00:00:09 +0000 (16:00 -0800)]
ocfs2: complete the rest request through buffer io
Complte the rest request thourgh buffer io after direct write performed.
Signed-off-by: Joseph Qi <joseph.qi@huawei.com> Cc: Weiwei Wang <wangww631@huawei.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Mark Fasheh <mfasheh@suse.com> Cc: Xuejiufei <xuejiufei@huawei.com> Cc: alex chen <alex.chen@huawei.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joseph Qi [Tue, 17 Feb 2015 00:00:06 +0000 (16:00 -0800)]
ocfs2: do not fallback to buffer I/O write if appending
Now we can do direct io and do not fallback to buffered IO any more in
case of append O_DIRECT write.
Signed-off-by: Joseph Qi <joseph.qi@huawei.com> Cc: Weiwei Wang <wangww631@huawei.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Mark Fasheh <mfasheh@suse.com> Cc: Xuejiufei <xuejiufei@huawei.com> Cc: alex chen <alex.chen@huawei.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joseph Qi [Tue, 17 Feb 2015 00:00:03 +0000 (16:00 -0800)]
ocfs2: allocate blocks in ocfs2_direct_IO_get_blocks
Allow blocks allocation in ocfs2_direct_IO_get_blocks.
Signed-off-by: Joseph Qi <joseph.qi@huawei.com> Cc: Weiwei Wang <wangww631@huawei.com> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Mark Fasheh <mfasheh@suse.com> Cc: Xuejiufei <xuejiufei@huawei.com> Cc: alex chen <alex.chen@huawei.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joseph Qi [Tue, 17 Feb 2015 00:00:00 +0000 (16:00 -0800)]
ocfs2: implement ocfs2_direct_IO_write
Implement ocfs2_direct_IO_write. Add the inode to orphan dir first, and
then delete it once append O_DIRECT finished.
This is to make sure block allocation and inode size are consistent.
[akpm@linux-foundation.org: fix it for "block: Add discard flag to blkdev_issue_zeroout() function"] Signed-off-by: Joseph Qi <joseph.qi@huawei.com> Cc: Weiwei Wang <wangww631@huawei.com> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Mark Fasheh <mfasheh@suse.com> Cc: Xuejiufei <xuejiufei@huawei.com> Cc: alex chen <alex.chen@huawei.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joseph Qi [Mon, 16 Feb 2015 23:59:57 +0000 (15:59 -0800)]
ocfs2: add orphan recovery types in ocfs2_recover_orphans
Define two orphan recovery types, which indicates if need truncate file or
not.
Signed-off-by: Joseph Qi <joseph.qi@huawei.com> Cc: Weiwei Wang <wangww631@huawei.com> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Mark Fasheh <mfasheh@suse.com> Cc: Xuejiufei <xuejiufei@huawei.com> Cc: alex chen <alex.chen@huawei.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joseph Qi [Mon, 16 Feb 2015 23:59:54 +0000 (15:59 -0800)]
ocfs2: add functions to add and remove inode in orphan dir
Add functions to add inode to orphan dir and remove inode in orphan dir.
Here we do not call ocfs2_prepare_orphan_dir and ocfs2_orphan_add
directly. Because append O_DIRECT will add inode to orphan two and may
result in more than one orphan entry for the same inode.
[akpm@linux-foundation.org: avoid dynamic stack allocation] Signed-off-by: Joseph Qi <joseph.qi@huawei.com> Cc: Weiwei Wang <wangww631@huawei.com> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Mark Fasheh <mfasheh@suse.com> Cc: Xuejiufei <xuejiufei@huawei.com> Cc: alex chen <alex.chen@huawei.com> Cc: Fengguang Wu <fengguang.wu@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joseph Qi [Mon, 16 Feb 2015 23:59:50 +0000 (15:59 -0800)]
ocfs2: prepare some interfaces used in append direct io
Currently in case of append O_DIRECT write (block not allocated yet),
ocfs2 will fall back to buffered I/O. This has some disadvantages.
Firstly, it is not the behavior as expected. Secondly, it will consume
huge page cache, e.g. in mass backup scenario. Thirdly, modern
filesystems such as ext4 support this feature.
In this patch set, the direct I/O write doesn't fallback to buffer I/O
write any more because the allocate blocks are enabled in direct I/O now.
This patch (of 9):
Prepare some interfaces which will be used in append O_DIRECT write.
Signed-off-by: Joseph Qi <joseph.qi@huawei.com> Cc: Weiwei Wang <wangww631@huawei.com> Cc: Mark Fasheh <mfasheh@suse.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Xuejiufei <xuejiufei@huawei.com> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: alex chen <alex.chen@huawei.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Matthew Wilcox [Mon, 16 Feb 2015 23:59:44 +0000 (15:59 -0800)]
dax: does not work correctly with virtual aliasing caches
The DAX code accesses the underlying storage through the kernel's linear
mapping, which may not be cache-coherent with user mappings on ARM, MIPS
or SPARC. Temporarily disable the DAX code until this problem is
resolved.
The original XIP code also had this problem, but it was never noticed.
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com> Cc: Andreas Dilger <andreas.dilger@intel.com> Cc: Boaz Harrosh <boaz@plexistor.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Dave Chinner <david@fromorbit.com> Cc: Jan Kara <jack@suse.cz> Cc: Jens Axboe <axboe@kernel.dk> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: Randy Dunlap <rdunlap@infradead.org> Cc: Ross Zwisler <ross.zwisler@linux.intel.com> Cc: Theodore Ts'o <tytso@mit.edu> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Russell King <rmk@arm.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Matthew Wilcox [Mon, 16 Feb 2015 23:59:35 +0000 (15:59 -0800)]
dax: add dax_zero_page_range
This new function allows us to support hole-punch for DAX files by zeroing
a partial page, as opposed to the dax_truncate_page() function which can
only truncate to the end of the page. Reimplement dax_truncate_page() to
call dax_zero_page_range().
[ross.zwisler@linux.intel.com: ported to 3.13-rc2]
[akpm@linux-foundation.org: fix typos in comments] Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com> Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com> Cc: Andreas Dilger <andreas.dilger@intel.com> Cc: Boaz Harrosh <boaz@plexistor.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Dave Chinner <david@fromorbit.com> Cc: Jan Kara <jack@suse.cz> Cc: Jens Axboe <axboe@kernel.dk> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: Randy Dunlap <rdunlap@infradead.org> Cc: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Matthew Wilcox [Mon, 16 Feb 2015 23:59:31 +0000 (15:59 -0800)]
ext2: get rid of most mentions of XIP in ext2
To help people transition, accept the 'xip' mount option (and report it in
/proc/mounts), but print a message encouraging people to switch over to
the 'dax' option.
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com> Reviewed-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: Andreas Dilger <andreas.dilger@intel.com> Cc: Boaz Harrosh <boaz@plexistor.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Dave Chinner <david@fromorbit.com> Cc: Jan Kara <jack@suse.cz> Cc: Jens Axboe <axboe@kernel.dk> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Randy Dunlap <rdunlap@infradead.org> Cc: Ross Zwisler <ross.zwisler@linux.intel.com> Cc: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Matthew Wilcox [Mon, 16 Feb 2015 23:59:15 +0000 (15:59 -0800)]
ext2: remove ext2_xip_verify_sb()
Jan Kara pointed out that calling ext2_xip_verify_sb() in ext2_remount()
doesn't make sense, since changing the XIP option on remount isn't
allowed. It also doesn't make sense to re-check whether blocksize is
supported since it can't change between mounts.
Replace the call to ext2_xip_verify_sb() in ext2_fill_super() with the
equivalent check and delete the definition.
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com> Cc: Andreas Dilger <andreas.dilger@intel.com> Cc: Boaz Harrosh <boaz@plexistor.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Dave Chinner <david@fromorbit.com> Cc: Jan Kara <jack@suse.cz> Cc: Jens Axboe <axboe@kernel.dk> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: Randy Dunlap <rdunlap@infradead.org> Cc: Ross Zwisler <ross.zwisler@linux.intel.com> Cc: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Matthew Wilcox [Mon, 16 Feb 2015 23:59:12 +0000 (15:59 -0800)]
vfs: remove get_xip_mem
All callers of get_xip_mem() are now gone. Remove checks for it,
initialisers of it, documentation of it and the only implementation of it.
Also remove mm/filemap_xip.c as it is now empty. Also remove
documentation of the long-gone get_xip_page().
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com> Cc: Andreas Dilger <andreas.dilger@intel.com> Cc: Boaz Harrosh <boaz@plexistor.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Dave Chinner <david@fromorbit.com> Cc: Jan Kara <jack@suse.cz> Cc: Jens Axboe <axboe@kernel.dk> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: Randy Dunlap <rdunlap@infradead.org> Cc: Ross Zwisler <ross.zwisler@linux.intel.com> Cc: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Matthew Wilcox [Mon, 16 Feb 2015 23:59:09 +0000 (15:59 -0800)]
dax: replace XIP documentation with DAX documentation
Based on the original XIP documentation, this documents the current state
of affairs, and includes instructions on how users can enable DAX if their
devices and kernel support it.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com> Reviewed-by: Randy Dunlap <rdunlap@infradead.org> Cc: Andreas Dilger <andreas.dilger@intel.com> Cc: Boaz Harrosh <boaz@plexistor.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Dave Chinner <david@fromorbit.com> Cc: Jan Kara <jack@suse.cz> Cc: Jens Axboe <axboe@kernel.dk> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: Ross Zwisler <ross.zwisler@linux.intel.com> Cc: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Matthew Wilcox [Mon, 16 Feb 2015 23:58:59 +0000 (15:58 -0800)]
dax,ext2: replace ext2_clear_xip_target with dax_clear_blocks
This is practically generic code; other filesystems will want to call it
from other places, but there's nothing ext2-specific about it.
Make it a little more generic by allowing it to take a count of the number
of bytes to zero rather than fixing it to a single page. Thanks to Dave
Hansen for suggesting that I need to call cond_resched() if zeroing more
than one page.
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com> Cc: Andreas Dilger <andreas.dilger@intel.com> Cc: Boaz Harrosh <boaz@plexistor.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Dave Chinner <david@fromorbit.com> Cc: Jan Kara <jack@suse.cz> Cc: Jens Axboe <axboe@kernel.dk> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: Randy Dunlap <rdunlap@infradead.org> Cc: Ross Zwisler <ross.zwisler@linux.intel.com> Cc: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Matthew Wilcox [Mon, 16 Feb 2015 23:58:56 +0000 (15:58 -0800)]
dax,ext2: replace XIP read and write with DAX I/O
Use the generic AIO infrastructure instead of custom read and write
methods. In addition to giving us support for AIO, this adds the missing
locking between read() and truncate().
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com> Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com> Reviewed-by: Jan Kara <jack@suse.cz> Cc: Andreas Dilger <andreas.dilger@intel.com> Cc: Boaz Harrosh <boaz@plexistor.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Dave Chinner <david@fromorbit.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: Randy Dunlap <rdunlap@infradead.org> Cc: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Matthew Wilcox [Mon, 16 Feb 2015 23:58:53 +0000 (15:58 -0800)]
vfs,ext2: introduce IS_DAX(inode)
Use an inode flag to tag inodes which should avoid using the page cache.
Convert ext2 to use it instead of mapping_is_xip(). Prevent I/Os to files
tagged with the DAX flag from falling back to buffered I/O.
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com> Reviewed-by: Jan Kara <jack@suse.cz> Reviewed-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: Andreas Dilger <andreas.dilger@intel.com> Cc: Boaz Harrosh <boaz@plexistor.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Dave Chinner <david@fromorbit.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Randy Dunlap <rdunlap@infradead.org> Cc: Ross Zwisler <ross.zwisler@linux.intel.com> Cc: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Matthew Wilcox [Mon, 16 Feb 2015 23:58:50 +0000 (15:58 -0800)]
mm: allow page fault handlers to perform the COW
Currently COW of an XIP file is done by first bringing in a read-only
mapping, then retrying the fault and copying the page. It is much more
efficient to tell the fault handler that a COW is being attempted (by
passing in the pre-allocated page in the vm_fault structure), and allow
the handler to perform the COW operation itself.
The handler cannot insert the page itself if there is already a read-only
mapping at that address, so allow the handler to return VM_FAULT_LOCKED
and set the fault_page to be NULL. This indicates to the MM code that the
i_mmap_lock is held instead of the page lock.
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com> Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Andreas Dilger <andreas.dilger@intel.com> Cc: Boaz Harrosh <boaz@plexistor.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Dave Chinner <david@fromorbit.com> Cc: Jan Kara <jack@suse.cz> Cc: Jens Axboe <axboe@kernel.dk> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: Randy Dunlap <rdunlap@infradead.org> Cc: Ross Zwisler <ross.zwisler@linux.intel.com> Cc: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Matthew Wilcox [Mon, 16 Feb 2015 23:58:46 +0000 (15:58 -0800)]
mm: fix XIP fault vs truncate race
DAX is a replacement for the variation of XIP currently supported by the
ext2 filesystem. We have three different things in the tree called 'XIP',
and the new focus is on access to data rather than executables, so a name
change was in order. DAX stands for Direct Access. The X is for
eXciting.
The new focus on data access has resulted in more careful attention to
races that exist in the current XIP code, but are not hit by the use-case
that it was designed for. XIP's architecture worked fine for ext2, but
DAX is architected to work with modern filsystems such as ext4 and XFS.
DAX is not intended for use with btrfs; the value that btrfs adds relies
on manipulating data and writing data to different locations, while DAX's
value is for write-in-place and keeping the kernel from touching the data.
DAX was developed in order to support NV-DIMMs, but it's become clear that
its usefuless extends beyond NV-DIMMs and there are several potential
customers including the tracing machinery. Other people want to place the
kernel log in an area of memory, as long as they have a BIOS that does not
clear DRAM on reboot.
Patch 1 is a bug fix, probably worth including in 3.18.
Patches 2 & 3 are infrastructure for DAX.
Patches 4-8 replace the XIP code with its DAX equivalents, transforming
ext2 to use the DAX code as we go. Note that patch 10 is the
Documentation patch.
Patches 9-15 clean up after the XIP code, removing the infrastructure
that is no longer needed and renaming various XIP things to DAX.
Most of these patches were added after Jan found things he didn't
like in an earlier version of the ext4 patch ... that had been copied
from ext2. So ext2 i being transformed to do things the same way that
ext4 will later. The ability to mount ext2 filesystems with the 'xip'
option is retained, although the 'dax' option is now preferred.
Patch 16 adds some DAX infrastructure to support ext4.
Patch 17 adds DAX support to ext4. It is broadly similar to ext2's DAX
support, but it is more efficient than ext4's due to its support for
unwritten extents.
Patch 18 is another cleanup patch renaming XIP to DAX.
My thanks to Mathieu Desnoyers for his reviews of the v11 patchset. Most
of the changes below were based on his feedback.
This patch (of 18):
Pagecache faults recheck i_size after taking the page lock to ensure that
the fault didn't race against a truncate. We don't have a page to lock in
the XIP case, so use i_mmap_lock_read() instead. It is locked in the
truncate path in unmap_mapping_range() after updating i_size. So while we
hold it in the fault path, we are guaranteed that either i_size has
already been updated in the truncate path, or that the truncate will
subsequently call zap_page_range_single() and so remove the mapping we
have just inserted.
There is a window of time in which i_size has been reduced and the thread
has a mapping to a page which will be removed from the file, but this is
harmless as the page will not be allocated to a different purpose before
the thread's access to it is revoked.
[akpm@linux-foundation.org: switch to i_mmap_lock_read(), add comment in unmap_single_vma()] Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com> Reviewed-by: Jan Kara <jack@suse.cz> Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Reviewed-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: Andreas Dilger <andreas.dilger@intel.com> Cc: Boaz Harrosh <boaz@plexistor.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Dave Chinner <david@fromorbit.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Randy Dunlap <rdunlap@infradead.org> Cc: Ross Zwisler <ross.zwisler@linux.intel.com> Cc: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Arnaud Ebalard [Mon, 16 Feb 2015 23:58:43 +0000 (15:58 -0800)]
arm: dts: zynq: update isl9305 compatible string to use isil vendor prefix
"isil" and "isl" prefixes are used at various locations inside the kernel
to reference Intersil corporation. This patch is part of a series fixing
those locations were "isl" is used in compatible strings to use the now
expected "isil" prefix instead (NASDAQ symbol for Intersil and most used
version).
Note: isl9305 is an I2C device so the patch does not in fact currently
depend on the introduction of "isil"-based compatible string in isl9305
driver (provided by another patch) because I2C core does not check the
prefix yet.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org> Cc: Rob Herring <robh+dt@kernel.org> Cc: Pawel Moll <pawel.moll@arm.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Ian Campbell <ijc+devicetree@hellion.org.uk> Cc: Kumar Gala <galak@codeaurora.org> Cc: Russell King <linux@arm.linux.org.uk> Cc: Stephen Warren <swarren@wwwdotorg.org> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: Alexandre Courbot <gnurou@gmail.com> Cc: Uwe Kleine-Knig <uwe@kleine-koenig.org> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: Peter Huewe <peter.huewe@infineon.com> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Mark Brown <broonie@kernel.org> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Darshana Padmadas <darshanapadmadas@gmail.com> Cc: Grant Likely <grant.likely@linaro.org> Cc: Rob Landley <rob@landley.net> Cc: Jason Cooper <jason@lakedaemon.net> Cc: Guenter Roeck <linux@roeck-us.net> Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Cc: Uwe Kleine-König <uwe@kleine-koenig.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Arnaud Ebalard [Mon, 16 Feb 2015 23:58:39 +0000 (15:58 -0800)]
staging: iio: isl29028: deprecate use of isl in compatible string for isil
"isil" and "isl" prefixes are used at various locations inside the kernel
to reference Intersil corporation. This patch is part of a series fixing
those locations were "isl" is used in compatible strings to use the now
expected "isil" prefix instead (NASDAQ symbol for Intersil and most used
version). The old compatible string is kept for backward compatibility.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org> Cc: Rob Herring <robh+dt@kernel.org> Cc: Pawel Moll <pawel.moll@arm.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Ian Campbell <ijc+devicetree@hellion.org.uk> Cc: Kumar Gala <galak@codeaurora.org> Cc: Russell King <linux@arm.linux.org.uk> Cc: Stephen Warren <swarren@wwwdotorg.org> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: Alexandre Courbot <gnurou@gmail.com> Cc: Uwe Kleine-Knig <uwe@kleine-koenig.org> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: Peter Huewe <peter.huewe@infineon.com> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Mark Brown <broonie@kernel.org> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Darshana Padmadas <darshanapadmadas@gmail.com> Cc: Grant Likely <grant.likely@linaro.org> Cc: Rob Landley <rob@landley.net> Cc: Jason Cooper <jason@lakedaemon.net> Cc: Guenter Roeck <linux@roeck-us.net> Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Cc: Uwe Kleine-König <uwe@kleine-koenig.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Arnaud Ebalard [Mon, 16 Feb 2015 23:58:35 +0000 (15:58 -0800)]
rtc: isl12057: deprecate use of isl in compatible string for isil
"isil" and "isl" prefixes are used at various locations inside the kernel
to reference Intersil corporation. This patch is part of a series fixing
those locations were "isl" is used in compatible strings to use the now
expected "isil" prefix instead (NASDAQ symbol for Intersil and most used
version). The old compatible string is kept for backward compatibility.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org> Cc: Rob Herring <robh+dt@kernel.org> Cc: Pawel Moll <pawel.moll@arm.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Ian Campbell <ijc+devicetree@hellion.org.uk> Cc: Kumar Gala <galak@codeaurora.org> Cc: Russell King <linux@arm.linux.org.uk> Cc: Stephen Warren <swarren@wwwdotorg.org> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: Alexandre Courbot <gnurou@gmail.com> Cc: Uwe Kleine-Knig <uwe@kleine-koenig.org> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: Peter Huewe <peter.huewe@infineon.com> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Mark Brown <broonie@kernel.org> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Darshana Padmadas <darshanapadmadas@gmail.com> Cc: Grant Likely <grant.likely@linaro.org> Cc: Rob Landley <rob@landley.net> Cc: Jason Cooper <jason@lakedaemon.net> Cc: Guenter Roeck <linux@roeck-us.net> Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Cc: Uwe Kleine-König <uwe@kleine-koenig.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Arnaud Ebalard [Mon, 16 Feb 2015 23:58:31 +0000 (15:58 -0800)]
rtc: isl12022: deprecate use of isl in compatible string for isil
"isil" and "isl" prefixes are used at various locations inside the kernel
to reference Intersil corporation. This patch is part of a series fixing
those locations were "isl" is used in compatible strings to use the now
expected "isil" prefix instead (NASDAQ symbol for Intersil and most used
version). The old compatible string is kept for backward compatibility.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org> Cc: Rob Herring <robh+dt@kernel.org> Cc: Pawel Moll <pawel.moll@arm.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Ian Campbell <ijc+devicetree@hellion.org.uk> Cc: Kumar Gala <galak@codeaurora.org> Cc: Russell King <linux@arm.linux.org.uk> Cc: Stephen Warren <swarren@wwwdotorg.org> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: Alexandre Courbot <gnurou@gmail.com> Cc: Uwe Kleine-Knig <uwe@kleine-koenig.org> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: Peter Huewe <peter.huewe@infineon.com> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Mark Brown <broonie@kernel.org> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Darshana Padmadas <darshanapadmadas@gmail.com> Cc: Grant Likely <grant.likely@linaro.org> Cc: Rob Landley <rob@landley.net> Cc: Jason Cooper <jason@lakedaemon.net> Cc: Guenter Roeck <linux@roeck-us.net> Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Cc: Uwe Kleine-König <uwe@kleine-koenig.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Mon, 16 Feb 2015 23:48:00 +0000 (15:48 -0800)]
Merge branch 'drm-next' of git://people.freedesktop.org/~airlied/linux
Pull drm updates from Dave Airlie:
"This is the main drm pull, it has a shared branch with some alsa
crossover but everything should be acked by relevant people.
New drivers:
- ATMEL HLCDC driver
- designware HDMI core support (used in multiple SoCs).
core:
- lots more atomic modesetting work, properties and atomic ioctl
(hidden under option)
- bridge rework allows support for Samsung exynos chromebooks to
work finally.
- some more panels supported
i915:
- atomic plane update support
- DSI uses shared DSI infrastructure
- Skylake basic support is all merged now
- component framework used for i915/snd-hda interactions
- write-combine cpu memory mappings
- engine init code refactored
- full ppgtt enabled where execlists are enabled.
- cherryview rps/gpu turbo and pipe CRC support.
radeon:
- indirect draw support for evergreen/cayman
- SMC and manual fan control for SI/CI
- Displayport audio support
amdkfd:
- SDMA usermode queue support
- replace suballocator usage with more suitable one
- rework for allowing interfacing to more than radeon
nouveau:
- major renaming in prep for later splitting work
- merge arm platform driver into nouveau
- GK20A reclocking support
msm:
- conversion to atomic modesetting
- YUV support for mdp4/5
- eDP support
- hw cursor for mdp5
tegra:
- conversion to atomic modesetting
- better suspend/resume support for child devices
rcar-du:
- interlaced support
imx:
- move to using dw_hdmi shared support
- mode_fixup support
sti:
- DVO support
- HDMI infoframe support
exynos:
- refactoring and cleanup, removed lots of internal unnecessary
abstraction
- exynos7 DECON display controller support
Along with the usual bunch of fixes, cleanups etc"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (724 commits)
drm/radeon: fix voltage setup on hawaii
drm/radeon/dp: Set EDP_CONFIGURATION_SET for bridge chips if necessary
drm/radeon: only enable kv/kb dpm interrupts once v3
drm/radeon: workaround for CP HW bug on CIK
drm/radeon: Don't try to enable write-combining without PAT
drm/radeon: use 0-255 rather than 0-100 for pwm fan range
drm/i915: Clamp efficient frequency to valid range
drm/i915: Really ignore long HPD pulses on eDP
drm/exynos: Add DECON driver
drm/i915: Correct the base value while updating LP_OUTPUT_HOLD in MIPI_PORT_CTRL
drm/i915: Insert a command barrier on BLT/BSD cache flushes
drm/i915: Drop vblank wait from intel_dp_link_down
drm/exynos: fix NULL pointer reference
drm/exynos: remove exynos_plane_dpms
drm/exynos: remove mode property of exynos crtc
drm/exynos: Remove exynos_plane_dpms() call with no effect
drm/i915: Squelch overzealous uncore reset WARN_ON
drm/i915: Take runtime pm reference on hangcheck_info
drm/i915: Correct the IOSF Dev_FN field for IOSF transfers
drm/exynos: fix DMA_ATTR_NO_KERNEL_MAPPING usage
...
Linus Torvalds [Mon, 16 Feb 2015 23:26:10 +0000 (15:26 -0800)]
Merge branch 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull clocksource updates from Ingo Molnar:
"The main change in this tree is the addition of various new SoC
clocksource/clockevents drivers: Conexant Digicolor SoCs, rockchip
rk3288 board, asm9260 for MIPS and versatile AB/PB boards"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
dts: versatile: Add sysregs node
clocksource: versatile: Adapt for Versatile AB and PB boards
dt/bindings: Add binding for Versatile system registers
clocksource: Driver for Conexant Digicolor SoC timer
clocksource: devicetree: Document Conexant Digicolor timer binding
clockevents: rockchip: Add rockchip timer for rk3288
ARM: clocksource: Add asm9260_timer driver
clocksource: marco: Rename marco to atlas7
clocksource: sirf: Remove unused variable
Linus Torvalds [Mon, 16 Feb 2015 23:20:40 +0000 (15:20 -0800)]
Merge branch 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irqchip updates from Ingo Molnar:
"Various irqchip driver updates, plus a genirq core update that allows
the initial spreading of irqs amonst CPUs without having to do it from
user-space"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq: Fix null pointer reference in irq_set_affinity_hint()
irqchip: gic: Allow interrupt level to be set for PPIs
irqchip: mips-gic: Handle pending interrupts once in __gic_irq_dispatch()
irqchip: Conexant CX92755 interrupts controller driver
irqchip: Devicetree: document Conexant Digicolor irq binding
irqchip: omap-intc: Remove unused legacy interface for omap2
irqchip: omap-intc: Fix support for dm814 and dm816
irqchip: mtk-sysirq: Get irq number from register resource size
irqchip: renesas-intc-irqpin: r8a7779 IRLM setup support
genirq: Set initial affinity in irq_set_affinity_hint()
Linus Torvalds [Mon, 16 Feb 2015 22:58:12 +0000 (14:58 -0800)]
Merge branch 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 perf updates from Ingo Molnar:
"This series tightens up RDPMC permissions: currently even highly
sandboxed x86 execution environments (such as seccomp) have permission
to execute RDPMC, which may leak various perf events / PMU state such
as timing information and other CPU execution details.
This 'all is allowed' RDPMC mode is still preserved as the
(non-default) /sys/devices/cpu/rdpmc=2 setting. The new default is
that RDPMC access is only allowed if a perf event is mmap-ed (which is
needed to correctly interpret RDPMC counter values in any case).
As a side effect of these changes CR4 handling is cleaned up in the
x86 code and a shadow copy of the CR4 value is added.
The extra CR4 manipulation adds ~ <50ns to the context switch cost
between rdpmc-capable and rdpmc-non-capable mms"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86: Add /sys/devices/cpu/rdpmc=2 to allow rdpmc for all tasks
perf/x86: Only allow rdpmc if a perf_event is mapped
perf: Pass the event to arch_perf_update_userpage()
perf: Add pmu callbacks to track event mapping and unmapping
x86: Add a comment clarifying LDT context switching
x86: Store a per-cpu shadow copy of CR4
x86: Clean up cr4 manipulation
Linus Torvalds [Mon, 16 Feb 2015 22:56:52 +0000 (14:56 -0800)]
Merge tag 'arc-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC updates from Vineet Gupta:
"Some fixes, nothing too exciting this time as well..."
* tag 'arc-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: fix page address calculation if PAGE_OFFSET != LINUX_LINK_BASE
ARC: Fix earlycon build breakage
ARC: Dynamically determine BASE_BAUD from DeviceTree
arc: Remove unused prepare_to_copy()
ARC: use ACCESS_ONCE in cmpxchg loop
ARC: add some more comments to ret_from_fork
ARC: fix /proc/cpuinfo for offline cpus
Dave Airlie [Mon, 16 Feb 2015 03:55:49 +0000 (13:55 +1000)]
Merge branch 'drm-next-3.20' of git://people.freedesktop.org/~agd5f/linux into drm-next
two important bug fixes for radeon
* 'drm-next-3.20' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: fix voltage setup on hawaii
drm/radeon/dp: Set EDP_CONFIGURATION_SET for bridge chips if necessary
Linus Torvalds [Sun, 15 Feb 2015 19:37:02 +0000 (11:37 -0800)]
Merge tag 'tty-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver patches from Greg KH:
"Here's the big tty/serial driver update for 3.20-rc1. Nothing huge
here, just lots of driver updates and some core tty layer fixes as
well. All have been in linux-next with no reported issues"
* tag 'tty-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (119 commits)
serial: 8250: Fix UART_BUG_TXEN workaround
serial: driver for ETRAX FS UART
tty: remove unused variable sprop
serial: of-serial: fetch line number from DT
serial: samsung: earlycon support depends on CONFIG_SERIAL_SAMSUNG_CONSOLE
tty/serial: serial8250_set_divisor() can be static
tty/serial: Add Spreadtrum sc9836-uart driver support
Documentation: DT: Add bindings for Spreadtrum SoC Platform
serial: samsung: remove redundant interrupt enabling
tty: Remove external interface for tty_set_termios()
serial: omap: Fix RTS handling
serial: 8250_omap: Use UPSTAT_AUTORTS for RTS handling
serial: core: Rework hw-assisted flow control support
tty/serial: 8250_early: Add support for PXA UARTs
tty/serial: of_serial: add support for PXA/MMP uarts
tty/serial: of_serial: add DT alias ID handling
serial: 8250: Prevent concurrent updates to shadow registers
serial: 8250: Use canary to restart console after suspend
serial: 8250: Refactor XR17V35X divisor calculation
serial: 8250: Refactor divisor programming
...
Linus Torvalds [Sun, 15 Feb 2015 19:30:39 +0000 (11:30 -0800)]
Merge tag 'staging-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging drivers patches from Greg KH:
"Here's the big staging driver tree update for 3.20-rc1.
Lots of little things in here, adding up to lots of overall cleanups.
The IIO driver updates are also in here as they cross the staging tree
boundry a lot. I2O has moved into staging as well, as a plan to drop
it from the tree eventually as that's a dead subsystem.
All of this has been in linux-next with no reported issues for a
while"
* tag 'staging-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (740 commits)
staging: lustre: lustre: libcfs: define symbols as static
staging: rtl8712: Do coding style cleanup
staging: lustre: make obd_updatemax_lock static
staging: rtl8188eu: core: switch with redundant cases
staging: rtl8188eu: odm: conditional setting with no effect
staging: rtl8188eu: odm: condition with no effect
staging: ft1000: fix braces warning
staging: sm7xxfb: fix remaining CamelCase
staging: sm7xxfb: fix CamelCase
staging: rtl8723au: multiple condition with no effect - if identical to else
staging: sm7xxfb: make smtc_scr_info static
staging/lustre/mdc: Initialize req in mdc_enqueue for !it case
staging/lustre/clio: Do not allow group locks with gid 0
staging/lustre/llite: don't add to page cache upon failure
staging/lustre/llite: Add exception entry check after radix_tree
staging/lustre/libcfs: protect kkuc_groups from write access
staging/lustre/fld: refer to MDT0 for fld lookup in some cases
staging/lustre/llite: Solve a race to access lli_has_smd in read case
staging/lustre/ptlrpc: hold rq_lock when modify rq_flags
staging/lustre/lnet: portal spreading rotor should be unsigned
...
Linus Torvalds [Sun, 15 Feb 2015 19:11:47 +0000 (11:11 -0800)]
Merge tag 'driver-core-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core patches from Greg KH:
"Really tiny set of patches for this kernel. Nothing major, all
described in the shortlog and have been in linux-next for a while"
* tag 'driver-core-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
sysfs: fix warning when creating a sysfs group without attributes
firmware_loader: handle timeout via wait_for_completion_interruptible_timeout()
firmware_loader: abort request if wait_for_completion is interrupted
firmware: Correct function name in comment
device: Change dev_<level> logging functions to return void
device: Fix dev_dbg_once macro
Linus Torvalds [Sun, 15 Feb 2015 18:48:44 +0000 (10:48 -0800)]
Merge tag 'char-misc-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc patches from Greg KH:
"Here's the big char/misc driver update for 3.20-rc1.
Lots of little things in here, all described in the changelog.
Nothing major or unusual, except maybe the binder selinux stuff, which
was all acked by the proper selinux people and they thought it best to
come through this tree.
All of this has been in linux-next with no reported issues for a while"
* tag 'char-misc-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (90 commits)
coresight: fix function etm_writel_cp14() parameter order
coresight-etm: remove check for unknown Kconfig macro
coresight: fixing CPU hwid lookup in device tree
coresight: remove the unnecessary function coresight_is_bit_set()
coresight: fix the debug AMBA bus name
coresight: remove the extra spaces
coresight: fix the link between orphan connection and newly added device
coresight: remove the unnecessary replicator property
coresight: fix the replicator subtype value
pdfdocs: Fix 'make pdfdocs' failure for 'uio-howto.tmpl'
mcb: Fix error path of mcb_pci_probe
virtio/console: verify device has config space
ti-st: clean up data types (fix harmless memory corruption)
mei: me: release hw from reset only during the reset flow
mei: mask interrupt set bit on clean reset bit
extcon: max77693: Constify struct regmap_config
extcon: adc-jack: Release IIO channel on driver remove
extcon: Remove duplicated include from extcon-class.c
Drivers: hv: vmbus: hv_process_timer_expiration() can be static
Drivers: hv: vmbus: serialize Offer and Rescind offer
...
Linus Torvalds [Sun, 15 Feb 2015 18:24:55 +0000 (10:24 -0800)]
Merge tag 'usb-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB patches from Greg KH:
"Here's the big pull request for the USB driver tree for 3.20-rc1.
Nothing major happening here, just lots of gadget driver updates, new
device ids, and a bunch of cleanups.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (299 commits)
usb: musb: fix device hotplug behind hub
usb: dwc2: Fix a bug in reading the endpoint directions from reg.
staging: emxx_udc: fix the build error
usb: Retry port status check on resume to work around RH bugs
Revert "usb: Reset USB-3 devices on USB-3 link bounce"
uhci-hub: use HUB_CHAR_*
usb: kconfig: replace PPC_OF with PPC
ehci-pci: disable for Intel MID platforms (update)
usb: gadget: Kconfig: use bool instead of boolean
usb: musb: blackfin: remove incorrect __exit_p()
USB: fix use-after-free bug in usb_hcd_unlink_urb()
ehci-pci: disable for Intel MID platforms
usb: host: pci_quirks: joing string literals
USB: add flag for HCDs that can't receive wakeup requests (isp1760-hcd)
USB: usbfs: allow URBs to be reaped after disconnection
cdc-acm: kill unnecessary messages
cdc-acm: add sanity checks
usb: phy: phy-generic: Fix USB PHY gpio reset
usb: dwc2: fix USB core dependencies
usb: renesas_usbhs: fix NULL pointer dereference in dma_release_channel()
...
Linus Torvalds [Sun, 15 Feb 2015 18:11:39 +0000 (10:11 -0800)]
Merge branch 'for-linus-v3.20' of git://git.infradead.org/linux-ubifs
Pull UBI and UBIFS updates from Richard Weinberger:
- cleanups and bug fixes all over UBI and UBIFS
- block-mq support for UBI Block
- UBI volumes can now be renamed while they are in use
- security.* XATTR support for UBIFS
- a maintainer update
* 'for-linus-v3.20' of git://git.infradead.org/linux-ubifs:
UBI: block: Fix checking for NULL instead of IS_ERR()
UBI: block: Continue creating ubiblocks after an initialization error
UBIFS: return -EINVAL if log head is empty
UBI: Block: Explain usage of blk_rq_map_sg()
UBI: fix soft lockup in ubi_check_volume()
UBI: Fastmap: Care about the protection queue
UBIFS: add a couple of extra asserts
UBI: do propagate positive error codes up
UBI: clean-up printing helpers
UBI: extend UBI layer debug/messaging capabilities - cosmetics
UBIFS: add ubifs_err() to print error reason
UBIFS: Add security.* XATTR support for the UBIFS
UBIFS: Add xattr support for symlinks
UBI: Block: Add blk-mq support
UBI: Add initial support for scatter gather
UBI: rename_volumes: Use UBI_METAONLY
UBI: Implement UBI_METAONLY
Add myself as UBI co-maintainer
Linus Torvalds [Sat, 14 Feb 2015 18:54:28 +0000 (10:54 -0800)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/borntraeger/linux
Pull ACCESS_ONCE() rule tightening from Christian Borntraeger:
"Tighten rules for ACCESS_ONCE
This series tightens the rules for ACCESS_ONCE to only work on scalar
types. It also contains the necessary fixups as indicated by build
bots of linux-next. Now everything is in place to prevent new
non-scalar users of ACCESS_ONCE and we can continue to convert code to
READ_ONCE/WRITE_ONCE"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/borntraeger/linux:
kernel: Fix sparse warning for ACCESS_ONCE
next: sh: Fix compile error
kernel: tighten rules for ACCESS ONCE
mm/gup: Replace ACCESS_ONCE with READ_ONCE
x86/spinlock: Leftover conversion ACCESS_ONCE->READ_ONCE
x86/xen/p2m: Replace ACCESS_ONCE with READ_ONCE
ppc/hugetlbfs: Replace ACCESS_ONCE with READ_ONCE
ppc/kvm: Replace ACCESS_ONCE with READ_ONCE
While working on arch/cris/include/asm/uaccess.h, I noticed
that some macros within this header are made harder to read because they
violate a coding style rule: space is missing after comma.
Fix it up.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
virtio wants to read bitwise types from userspace using get_user. At the
moment this triggers sparse errors, since the value is passed through an
integer.
Fix that up using __force.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Pull crypto update from Herbert Xu:
"Here is the crypto update for 3.20:
- Added 192/256-bit key support to aesni GCM.
- Added MIPS OCTEON MD5 support.
- Fixed hwrng starvation and race conditions.
- Added note that memzero_explicit is not a subsitute for memset.
- Added user-space interface for crypto_rng.
- Misc fixes"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (71 commits)
crypto: tcrypt - do not allocate iv on stack for aead speed tests
crypto: testmgr - limit IV copy length in aead tests
crypto: tcrypt - fix buflen reminder calculation
crypto: testmgr - mark rfc4106(gcm(aes)) as fips_allowed
crypto: caam - fix resource clean-up on error path for caam_jr_init
crypto: caam - pair irq map and dispose in the same function
crypto: ccp - terminate ccp_support array with empty element
crypto: caam - remove unused local variable
crypto: caam - remove dead code
crypto: caam - don't emit ICV check failures to dmesg
hwrng: virtio - drop extra empty line
crypto: replace scatterwalk_sg_next with sg_next
crypto: atmel - Free memory in error path
crypto: doc - remove colons in comments
crypto: seqiv - Ensure that IV size is at least 8 bytes
crypto: cts - Weed out non-CBC algorithms
MAINTAINERS: add linux-crypto to hw random
crypto: cts - Remove bogus use of seqiv
crypto: qat - don't need qat_auth_state struct
crypto: algif_rng - fix sparse non static symbol warning
...
Linus Torvalds [Sat, 14 Feb 2015 17:22:35 +0000 (09:22 -0800)]
Merge branch 'akpm' (patches from Andrew)
Merge fourth set of updates from Andrew Morton:
- the rest of lib/
- checkpatch updates
- a few misc things
- kasan: kernel address sanitizer
- the rtc tree
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (108 commits)
ARM: mvebu: enable Armada 38x RTC driver in mvebu_v7_defconfig
ARM: mvebu: add Device Tree description of RTC on Armada 38x
MAINTAINERS: add the RTC driver for the Armada38x
drivers/rtc/rtc-armada38x: add a new RTC driver for recent mvebu SoCs
rtc: armada38x: add the device tree binding documentation
rtc: rtc-ab-b5ze-s3: add sub-minute alarm support
rtc: add support for Abracon AB-RTCMC-32.768kHz-B5ZE-S3 I2C RTC chip
of: add vendor prefix for Abracon Corporation
drivers/rtc/rtc-rk808.c: fix rtc time reading issue
drivers/rtc/rtc-isl12057.c: constify struct regmap_config
drivers/rtc/rtc-at91sam9.c: constify struct regmap_config
drivers/rtc/rtc-imxdi.c: add more known register bits
drivers/rtc/rtc-imxdi.c: trivial clean up code
ARM: mvebu: ISL12057 rtc chip can now wake up RN102, RN102 and RN2120
rtc: rtc-isl12057: add isil,irq2-can-wakeup-machine property for in-tree users
drivers/rtc/rtc-isl12057.c: add alarm support to Intersil ISL12057 RTC driver
drivers/rtc/rtc-pcf2123.c: add support for devicetree
kprobes: makes kprobes/enabled works correctly for optimized kprobes.
kprobes: set kprobes_all_disarmed earlier to enable re-optimization.
init: remove CONFIG_INIT_FALLBACK
...
Gregory CLEMENT [Fri, 13 Feb 2015 22:41:18 +0000 (14:41 -0800)]
ARM: mvebu: add Device Tree description of RTC on Armada 38x
The Marvell Armada 38x SoCs contains an RTC which differs from the RTC
used in the other mvebu SoCs until now. This commit adds the Device Tree
description of this interface at the SoC level.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: Jason Cooper <jason@lakedaemon.net> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Cc: Arnaud Ebalard <arno@natisbad.org> Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com> Cc: Maxime Ripard <maxime.ripard@free-electrons.com> Cc: Boris BREZILLON <boris.brezillon@free-electrons.com> Cc: Lior Amsalem <alior@marvell.com> Cc: Tawfik Bayouk <tawfik@marvell.com> Cc: Nadav Haklai <nadavh@marvell.com> Cc: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Gregory CLEMENT [Fri, 13 Feb 2015 22:41:07 +0000 (14:41 -0800)]
rtc: armada38x: add the device tree binding documentation
The Marvell Armada 38x SoCs contains an RTC which differs from the RTC
used in the other mvebu SoCs until now. This forth version of the patch
set adds support for this new IP and enable it in the Device Tree of the
Armada 38x SoC.
This patch (of 5):
The Armada 38x SoCs come with a new RTC which differs from the one used in
the other mvebu SoCs until now. This patch describes the binding of this
RTC.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: Jason Cooper <jason@lakedaemon.net> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Cc: Arnaud Ebalard <arno@natisbad.org> Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com> Cc: Maxime Ripard <maxime.ripard@free-electrons.com> Cc: Boris BREZILLON <boris.brezillon@free-electrons.com> Cc: Lior Amsalem <alior@marvell.com> Cc: Tawfik Bayouk <tawfik@marvell.com> Cc: Nadav Haklai <nadavh@marvell.com> Cc: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Arnaud Ebalard [Fri, 13 Feb 2015 22:41:04 +0000 (14:41 -0800)]
rtc: rtc-ab-b5ze-s3: add sub-minute alarm support
Abracon AB-RTCMC-32.768kHz-B5ZE-S3 alarm is only accurate to the minute.
For that reason, UIE mode is currently not supported by the driver. But
the device provides a watchdog timer which can be coupled with the alarm
mechanism to extend support and provide sub-minute alarm capability.
This patch implements that extension. More precisely, it makes use of the
watchdog timer for alarms which are less that four minutes in the future
(with second accuracy) and use standard alarm mechanism for other alarms
(with minute accuracy).
Signed-off-by: Arnaud Ebalard <arno@natisbad.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: Peter Huewe <peter.huewe@infineon.com> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Thierry Reding <treding@nvidia.com> Cc: Mark Brown <broonie@kernel.org> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Rob Herring <robherring2@gmail.com> Cc: Pawel Moll <pawel.moll@arm.com> Cc: Stephen Warren <swarren@wwwdotorg.org> Cc: Ian Campbell <ijc+devicetree@hellion.org.uk> Cc: Grant Likely <grant.likely@linaro.org> Cc: Rob Landley <rob@landley.net> Cc: Jason Cooper <jason@lakedaemon.net> Cc: Guenter Roeck <linux@roeck-us.net> Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Cc: Kumar Gala <galak@codeaurora.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Arnaud Ebalard [Fri, 13 Feb 2015 22:41:00 +0000 (14:41 -0800)]
rtc: add support for Abracon AB-RTCMC-32.768kHz-B5ZE-S3 I2C RTC chip
This patch adds support for Abracon AB-RTCMC-32.768kHz-B5ZE-S3
RTC/Calendar module w/ I2C interface.
This support includes RTC time reading and setting, Alarm (1 minute
accuracy) reading and setting, and battery low detection. The device also
supports frequency adjustment and two timers but those features are
currently not implemented in this driver. Due to alarm accuracy
limitation (and current lack of timer support in the driver), UIE mode is
not supported.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: Peter Huewe <peter.huewe@infineon.com> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Thierry Reding <treding@nvidia.com> Cc: Mark Brown <broonie@kernel.org> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Rob Herring <robherring2@gmail.com> Cc: Pawel Moll <pawel.moll@arm.com> Cc: Stephen Warren <swarren@wwwdotorg.org> Cc: Ian Campbell <ijc+devicetree@hellion.org.uk> Cc: Grant Likely <grant.likely@linaro.org> Cc: Rob Landley <rob@landley.net> Cc: Jason Cooper <jason@lakedaemon.net> Cc: Guenter Roeck <linux@roeck-us.net> Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Cc: Kumar Gala <galak@codeaurora.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Arnaud Ebalard [Fri, 13 Feb 2015 22:40:57 +0000 (14:40 -0800)]
of: add vendor prefix for Abracon Corporation
This series adds support for Abracon AB-RTCMC-32.768kHz-B5ZE-S3 I2C RTC
chip. Unlike many RTC chips, it includes an internal oscillator which
spares room on the PCB. It also has some interesting features, like
battery low detection (which the driver in this series supports). The
only small "limitation" (mainly due to what RTC subsystem expects from
RTC chips) is the fact that its alarm is accurate to the second. This
series provides a solution (described below) for that limitation using
another mechanism of the chip.
I decided to split support between three different patches for
this v0:
- Patch 1/3: it simply references Abracon Corporation in vendor-prefixes
documentation file. As Abracon has no NASDAQ ticker symbol; I have
decided to use "abcn" (I initially started my work w/ "ab" but later
changed for "abcn" which looked more meaningful)
- Patch 2/3: it adds initial support for the chip and provides the
ability to read/write time and also read/write alarm. As the alarm
the chip provides is accurate to the minute, the support provided
by this patch also has this limitation (e.g. UIE mode is not
supported).
- Patch 3/3: the chip supports a watchdog timer which can be used to
extend the alarm mechanism in patch 2/3 in order to provide support
for alarms under one minute (e.g. support UIE mode). In practice,
the logic I implemented is to use the watchdog timer for alarms which
are at most 4 minutes in the future and use the common alarm mechanism
for alarms which are set to larger values. With that additional patch
the device fully passes the rtctest.c program.
I decided to split the driver between two patches (2 and 3 of 3) in
order to ease review: patch 2 should be pretty straightforward to read
for someone familiar w/ RTC subsystem. Patch 3 only extends what is in
patch 2 regarding alarms.
This patch (of 3):
Documentation/devicetree/bindings/vendor-prefixes.txt: add vendor prefix
for Abracon Corporation
Signed-off-by: Arnaud Ebalard <arno@natisbad.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: Peter Huewe <peter.huewe@infineon.com> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Thierry Reding <treding@nvidia.com> Cc: Mark Brown <broonie@kernel.org> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Rob Herring <robherring2@gmail.com> Cc: Pawel Moll <pawel.moll@arm.com> Cc: Stephen Warren <swarren@wwwdotorg.org> Cc: Ian Campbell <ijc+devicetree@hellion.org.uk> Cc: Grant Likely <grant.likely@linaro.org> Cc: Rob Landley <rob@landley.net> Cc: Jason Cooper <jason@lakedaemon.net> Cc: Guenter Roeck <linux@roeck-us.net> Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Cc: Kumar Gala <galak@codeaurora.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Chris Zhong [Fri, 13 Feb 2015 22:40:54 +0000 (14:40 -0800)]
drivers/rtc/rtc-rk808.c: fix rtc time reading issue
After we set the GET_TIME bit, the rtc time can't be read immediately. We
should wait up to 31.25 us, about one cycle of 32khz. Otherwise reading
RTC time will return a old time. If we clear the GET_TIME bit after
setting, the time of i2c transfer is certainly more than 31.25us.
Doug said:
: I think we are safe. At 400kHz (the max speed of this part) each bit can
: be transferred no faster than 2.5us. In order to do a valid i2c
: transaction we need to _at least_ write the address of the device and the
: data onto the bus, which is 16 bits. 16 * 2.5us = 40us. That's above the
: 31.25us
[akpm@linux-foundation.org: tweak comment per review discussion] Signed-off-by: Chris Zhong <zyw@rock-chips.com> Reviewed-by: Doug Anderson <dianders@chromium.org> Cc: Sonny Rao <sonnyrao@chromium.org> Cc: Heiko Stübner <heiko@sntech.de> Cc: Alessandro Zummo <a.zummo@towertech.it> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Juergen Borleis [Fri, 13 Feb 2015 22:40:45 +0000 (14:40 -0800)]
drivers/rtc/rtc-imxdi.c: add more known register bits
Intended for monitoring and controlling the security features. These bits
are required to bring this unit back to live after a security violation
event was detected. The code to bring it back to live will follow after a
vendor clearance.
Arnaud Ebalard [Fri, 13 Feb 2015 22:40:39 +0000 (14:40 -0800)]
ARM: mvebu: ISL12057 rtc chip can now wake up RN102, RN102 and RN2120
Now that alarm support for ISL12057 chip is available w/ the specific
"isil,irq2-can-wakeup-machine" property, let's use that feature of the
driver dedicated to NETGEAR ReadyNAS 102, 104 and 2120 specific routing of
RTC Alarm IRQ#2 pin; on those devices, this pin is not connected to the
SoC but to a PMIC, which allows the device to be powered up when RTC alarm
rings.
For that to work, the chip needs to be explicitly marked as a device
wakeup source using this "isil,irq2-can-wakeup-machine" boolean property.
This makes 'wakealarm' sysfs entry available to configure the alarm.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: Peter Huewe <peter.huewe@infineon.com> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Thierry Reding <treding@nvidia.com> Cc: Mark Brown <broonie@kernel.org> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Darshana Padmadas <darshanapadmadas@gmail.com> Cc: Rob Herring <rob.herring@calxeda.com> Cc: Pawel Moll <pawel.moll@arm.com> Cc: Stephen Warren <swarren@wwwdotorg.org> Cc: Ian Campbell <ijc+devicetree@hellion.org.uk> Cc: Grant Likely <grant.likely@linaro.org> Cc: Rob Landley <rob@landley.net> Cc: Jason Cooper <jason@lakedaemon.net> Cc: Guenter Roeck <linux@roeck-us.net> Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Cc: Kumar Gala <galak@codeaurora.org> Cc: Uwe Kleine-König <uwe@kleine-koenig.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Arnaud Ebalard [Fri, 13 Feb 2015 22:40:35 +0000 (14:40 -0800)]
rtc: rtc-isl12057: add isil,irq2-can-wakeup-machine property for in-tree users
Current in-tree users of ISL12057 RTC chip (NETGEAR ReadyNAS 102, 104 and
2120) do not have the IRQ#2 pin of the chip (associated w/ the Alarm1
mechanism) connected to their SoC, but to a PMIC (TPS65251 FWIW). This
specific hardware configuration allows the NAS to wake up when the alarms
rings.
Recently introduced alarm support for ISL12057 relies on the provision of
an "interrupts" property in system .dts file, which previous three users
will never get. For that reason, alarm support on those devices is not
function. To support this use case, this patch adds a new DT property for
ISL12057 (isil,irq2-can-wakeup-machine) to indicate that the chip is
capable of waking up the device using its IRQ#2 pin (even though it does
not have its IRQ#2 pin connected directly to the SoC).
This specific configuration was tested on a ReadyNAS 102 by setting an
alarm, powering off the device and see it reboot as expected when the
alarm rang w/:
As a side note, the ISL12057 remains in the list of trivial devices,
because the property is not per se required by the device to work but can
help handle system w/ specific requirements. In exchange, the new feature
is described in details in a specific documentation file.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: Peter Huewe <peter.huewe@infineon.com> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Thierry Reding <treding@nvidia.com> Cc: Mark Brown <broonie@kernel.org> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Darshana Padmadas <darshanapadmadas@gmail.com> Cc: Rob Herring <rob.herring@calxeda.com> Cc: Pawel Moll <pawel.moll@arm.com> Cc: Stephen Warren <swarren@wwwdotorg.org> Cc: Ian Campbell <ijc+devicetree@hellion.org.uk> Cc: Grant Likely <grant.likely@linaro.org> Cc: Rob Landley <rob@landley.net> Cc: Jason Cooper <jason@lakedaemon.net> Cc: Guenter Roeck <linux@roeck-us.net> Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Cc: Kumar Gala <galak@codeaurora.org> Cc: Uwe Kleine-König <uwe@kleine-koenig.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Arnaud Ebalard [Fri, 13 Feb 2015 22:40:32 +0000 (14:40 -0800)]
drivers/rtc/rtc-isl12057.c: add alarm support to Intersil ISL12057 RTC driver
This patch adds alarm support to Intersil ISL12057 driver. This allows to
configure the chip to generate an interrupt when the alarm matches current
time value. Alarm can be programmed up to one month in the future and is
accurate to the second.
The patch was developed to support two different configurations: systems
w/ and w/o RTC chip IRQ line connected to the main CPU.
The latter is the one found on current 3 kernel users of the chip for
which support was initially developed (Netgear ReadyNAS 102, 104 and 2120
NAS). On those devices, the IRQ#2 pin of the chip is not connected to the
SoC but to a PMIC. This allows setting an alarm, powering off the device
and have it wake up when the alarm rings. To support that configuration
the driver does the following:
1. it has alarm_irq_enable() function returns -ENOTTY when no IRQ
is passed to the driver.
2. it marks the device as a wakeup source in all cases (whether an
IRQ is passed to the driver or not) to have 'wakealarm' sysfs
entry created.
3. it marks the device has not supporting UIE mode when no IRQ is
passed to the driver (see the commmit message of c9f5c7e7a84f)
This specific configuration was tested on a ReadyNAS 102 by setting an
alarm, powering off the device and see it reboot as expected when the
alarm rang.
The former configuration was tested on a Netgear ReadyNAS 102 after some
soldering of the IRQ#2 pin of the RTC chip to a MPP line of the SoC (the
one used usually handles the reset button). The test was performed using
a modified .dts file reflecting this change (see below) and rtc-test.c
program available in Documentation/rtc.txt. This test program ran as
expected, which validates alarm supports, including interrupt support.
As a side note, the ISL12057 remains in the list of trivial devices, i.e.
no specific DT binding being added by this patch: i2c core automatically
handles extraction of IRQ line info from .dts file. For instance, if one
wants to reference the interrupt line for the alarm in its .dts file,
adding interrupt and interrupt-parent properties works as expected:
FWIW, if someone is looking for a way to test alarm support on a system on
which the chip IRQ line has the ability to boot the system (e.g. ReadyNAS
102, 104, etc):
Wang Nan [Fri, 13 Feb 2015 22:40:26 +0000 (14:40 -0800)]
kprobes: makes kprobes/enabled works correctly for optimized kprobes.
debugfs/kprobes/enabled doesn't work correctly on optimized kprobes.
Masami Hiramatsu has a test report on x86_64 platform:
https://lkml.org/lkml/2015/1/19/274
This patch forces it to unoptimize kprobe if kprobes_all_disarmed is set.
It also checks the flag in unregistering path for skipping unneeded
disarming process when kprobes globally disarmed.
Signed-off-by: Wang Nan <wangnan0@huawei.com> Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com> Cc: Ingo Molnar <mingo@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is because original code checks kprobes_all_disarmed in
optimize_kprobe(), but this flag is turned off after calling that
function. Therefore, optimize_kprobe() will see kprobes_all_disarmed ==
true and doesn't do the optimization.
This patch simply turns off kprobes_all_disarmed earlier to enable
optimization.
Signed-off-by: Wang Nan <wangnan0@huawei.com> Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com> Cc: Ingo Molnar <mingo@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrey Ryabinin [Fri, 13 Feb 2015 22:40:17 +0000 (14:40 -0800)]
kasan: enable instrumentation of global variables
This feature let us to detect accesses out of bounds of global variables.
This will work as for globals in kernel image, so for globals in modules.
Currently this won't work for symbols in user-specified sections (e.g.
__init, __read_mostly, ...)
The idea of this is simple. Compiler increases each global variable by
redzone size and add constructors invoking __asan_register_globals()
function. Information about global variable (address, size, size with
redzone ...) passed to __asan_register_globals() so we could poison
variable's redzone.
This patch also forces module_alloc() to return 8*PAGE_SIZE aligned
address making shadow memory handling (
kasan_module_alloc()/kasan_module_free() ) more simple. Such alignment
guarantees that each shadow page backing modules address space correspond
to only one module_alloc() allocation.
Signed-off-by: Andrey Ryabinin <a.ryabinin@samsung.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Konstantin Serebryany <kcc@google.com> Cc: Dmitry Chernenkov <dmitryc@google.com> Signed-off-by: Andrey Konovalov <adech.fo@gmail.com> Cc: Yuri Gribov <tetra2005@gmail.com> Cc: Konstantin Khlebnikov <koct9i@gmail.com> Cc: Sasha Levin <sasha.levin@oracle.com> Cc: Christoph Lameter <cl@linux.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Dave Hansen <dave.hansen@intel.com> Cc: Andi Kleen <andi@firstfloor.org> Cc: Ingo Molnar <mingo@elte.hu> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Christoph Lameter <cl@linux.com> Cc: Pekka Enberg <penberg@kernel.org> Cc: David Rientjes <rientjes@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrey Ryabinin [Fri, 13 Feb 2015 22:40:13 +0000 (14:40 -0800)]
module: fix types of device tables aliases
MODULE_DEVICE_TABLE() macro used to create aliases to device tables.
Normally alias should have the same type as aliased symbol.
Device tables are arrays, so they have 'struct type##_device_id[x]'
types. Alias created by MODULE_DEVICE_TABLE() will have non-array type -
'struct type##_device_id'.
This inconsistency confuses compiler, it could make a wrong assumption
about variable's size which leads KASan to produce a false positive report
about out of bounds access.
For every global variable compiler calls __asan_register_globals() passing
information about global variable (address, size, size with redzone, name
...) __asan_register_globals() poison symbols redzone to detect possible
out of bounds accesses.
When symbol has an alias __asan_register_globals() will be called as for
symbol so for alias. Compiler determines size of variable by size of
variable's type. Alias and symbol have the same address, so if alias have
the wrong size part of memory that actually belongs to the symbol could be
poisoned as redzone of alias symbol.
By fixing type of alias symbol we will fix size of it, so
__asan_register_globals() will not poison valid memory.
Signed-off-by: Andrey Ryabinin <a.ryabinin@samsung.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Konstantin Serebryany <kcc@google.com> Cc: Dmitry Chernenkov <dmitryc@google.com> Signed-off-by: Andrey Konovalov <adech.fo@gmail.com> Cc: Yuri Gribov <tetra2005@gmail.com> Cc: Konstantin Khlebnikov <koct9i@gmail.com> Cc: Sasha Levin <sasha.levin@oracle.com> Cc: Christoph Lameter <cl@linux.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Dave Hansen <dave.hansen@intel.com> Cc: Andi Kleen <andi@firstfloor.org> Cc: Ingo Molnar <mingo@elte.hu> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Christoph Lameter <cl@linux.com> Cc: Pekka Enberg <penberg@kernel.org> Cc: David Rientjes <rientjes@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrey Ryabinin [Fri, 13 Feb 2015 22:40:10 +0000 (14:40 -0800)]
kernel: add support for .init_array.* constructors
KASan uses constructors for initializing redzones for global variables.
Globals instrumentation in GCC 4.9.2 produces constructors with priority
(.init_array.00099)
Currently kernel ignores such constructors. Only constructors with
default priority supported (.init_array)
This patch adds support for constructors with priorities. For kernel
image we put pointers to constructors between __ctors_start/__ctors_end
and do_ctors() will call them on start up. For modules we merge
.init_array.* sections into resulting .init_array. Module code properly
handles constructors in .init_array section.
Signed-off-by: Andrey Ryabinin <a.ryabinin@samsung.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Konstantin Serebryany <kcc@google.com> Cc: Dmitry Chernenkov <dmitryc@google.com> Signed-off-by: Andrey Konovalov <adech.fo@gmail.com> Cc: Yuri Gribov <tetra2005@gmail.com> Cc: Konstantin Khlebnikov <koct9i@gmail.com> Cc: Sasha Levin <sasha.levin@oracle.com> Cc: Christoph Lameter <cl@linux.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Dave Hansen <dave.hansen@intel.com> Cc: Andi Kleen <andi@firstfloor.org> Cc: Ingo Molnar <mingo@elte.hu> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Christoph Lameter <cl@linux.com> Cc: Pekka Enberg <penberg@kernel.org> Cc: David Rientjes <rientjes@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrey Ryabinin [Fri, 13 Feb 2015 22:40:07 +0000 (14:40 -0800)]
mm: vmalloc: pass additional vm_flags to __vmalloc_node_range()
For instrumenting global variables KASan will shadow memory backing memory
for modules. So on module loading we will need to allocate memory for
shadow and map it at address in shadow that corresponds to the address
allocated in module_alloc().
__vmalloc_node_range() could be used for this purpose, except it puts a
guard hole after allocated area. Guard hole in shadow memory should be a
problem because at some future point we might need to have a shadow memory
at address occupied by guard hole. So we could fail to allocate shadow
for module_alloc().
Now we have VM_NO_GUARD flag disabling guard page, so we need to pass into
__vmalloc_node_range(). Add new parameter 'vm_flags' to
__vmalloc_node_range() function.
Signed-off-by: Andrey Ryabinin <a.ryabinin@samsung.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Konstantin Serebryany <kcc@google.com> Cc: Dmitry Chernenkov <dmitryc@google.com> Signed-off-by: Andrey Konovalov <adech.fo@gmail.com> Cc: Yuri Gribov <tetra2005@gmail.com> Cc: Konstantin Khlebnikov <koct9i@gmail.com> Cc: Sasha Levin <sasha.levin@oracle.com> Cc: Christoph Lameter <cl@linux.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Dave Hansen <dave.hansen@intel.com> Cc: Andi Kleen <andi@firstfloor.org> Cc: Ingo Molnar <mingo@elte.hu> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Christoph Lameter <cl@linux.com> Cc: Pekka Enberg <penberg@kernel.org> Cc: David Rientjes <rientjes@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrey Ryabinin [Fri, 13 Feb 2015 22:40:03 +0000 (14:40 -0800)]
mm: vmalloc: add flag preventing guard hole allocation
For instrumenting global variables KASan will shadow memory backing memory
for modules. So on module loading we will need to allocate memory for
shadow and map it at address in shadow that corresponds to the address
allocated in module_alloc().
__vmalloc_node_range() could be used for this purpose, except it puts a
guard hole after allocated area. Guard hole in shadow memory should be a
problem because at some future point we might need to have a shadow memory
at address occupied by guard hole. So we could fail to allocate shadow
for module_alloc().
Add a new vm_struct flag 'VM_NO_GUARD' indicating that vm area doesn't
have a guard hole.
Signed-off-by: Andrey Ryabinin <a.ryabinin@samsung.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Konstantin Serebryany <kcc@google.com> Cc: Dmitry Chernenkov <dmitryc@google.com> Signed-off-by: Andrey Konovalov <adech.fo@gmail.com> Cc: Yuri Gribov <tetra2005@gmail.com> Cc: Konstantin Khlebnikov <koct9i@gmail.com> Cc: Sasha Levin <sasha.levin@oracle.com> Cc: Christoph Lameter <cl@linux.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Dave Hansen <dave.hansen@intel.com> Cc: Andi Kleen <andi@firstfloor.org> Cc: Ingo Molnar <mingo@elte.hu> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Christoph Lameter <cl@linux.com> Cc: Pekka Enberg <penberg@kernel.org> Cc: David Rientjes <rientjes@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrey Ryabinin [Fri, 13 Feb 2015 22:39:59 +0000 (14:39 -0800)]
kasan: enable stack instrumentation
Stack instrumentation allows to detect out of bounds memory accesses for
variables allocated on stack. Compiler adds redzones around every
variable on stack and poisons redzones in function's prologue.
Such approach significantly increases stack usage, so all in-kernel stacks
size were doubled.
Signed-off-by: Andrey Ryabinin <a.ryabinin@samsung.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Konstantin Serebryany <kcc@google.com> Cc: Dmitry Chernenkov <dmitryc@google.com> Signed-off-by: Andrey Konovalov <adech.fo@gmail.com> Cc: Yuri Gribov <tetra2005@gmail.com> Cc: Konstantin Khlebnikov <koct9i@gmail.com> Cc: Sasha Levin <sasha.levin@oracle.com> Cc: Christoph Lameter <cl@linux.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Dave Hansen <dave.hansen@intel.com> Cc: Andi Kleen <andi@firstfloor.org> Cc: Ingo Molnar <mingo@elte.hu> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Christoph Lameter <cl@linux.com> Cc: Pekka Enberg <penberg@kernel.org> Cc: David Rientjes <rientjes@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrey Ryabinin [Fri, 13 Feb 2015 22:39:56 +0000 (14:39 -0800)]
x86_64: kasan: add interceptors for memset/memmove/memcpy functions
Recently instrumentation of builtin functions calls was removed from GCC
5.0. To check the memory accessed by such functions, userspace asan
always uses interceptors for them.
So now we should do this as well. This patch declares
memset/memmove/memcpy as weak symbols. In mm/kasan/kasan.c we have our
own implementation of those functions which checks memory before accessing
it.
Default memset/memmove/memcpy now now always have aliases with '__'
prefix. For files that built without kasan instrumentation (e.g.
mm/slub.c) original mem* replaced (via #define) with prefixed variants,
cause we don't want to check memory accesses there.
Signed-off-by: Andrey Ryabinin <a.ryabinin@samsung.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Konstantin Serebryany <kcc@google.com> Cc: Dmitry Chernenkov <dmitryc@google.com> Signed-off-by: Andrey Konovalov <adech.fo@gmail.com> Cc: Yuri Gribov <tetra2005@gmail.com> Cc: Konstantin Khlebnikov <koct9i@gmail.com> Cc: Sasha Levin <sasha.levin@oracle.com> Cc: Christoph Lameter <cl@linux.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Dave Hansen <dave.hansen@intel.com> Cc: Andi Kleen <andi@firstfloor.org> Cc: Ingo Molnar <mingo@elte.hu> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Christoph Lameter <cl@linux.com> Cc: Pekka Enberg <penberg@kernel.org> Cc: David Rientjes <rientjes@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrey Ryabinin [Fri, 13 Feb 2015 22:39:53 +0000 (14:39 -0800)]
lib: add kasan test module
This is a test module doing various nasty things like out of bounds
accesses, use after free. It is useful for testing kernel debugging
features like kernel address sanitizer.
It mostly concentrates on testing of slab allocator, but we might want to
add more different stuff here in future (like stack/global variables out
of bounds accesses and so on).
Signed-off-by: Andrey Ryabinin <a.ryabinin@samsung.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Konstantin Serebryany <kcc@google.com> Cc: Dmitry Chernenkov <dmitryc@google.com> Signed-off-by: Andrey Konovalov <adech.fo@gmail.com> Cc: Yuri Gribov <tetra2005@gmail.com> Cc: Konstantin Khlebnikov <koct9i@gmail.com> Cc: Sasha Levin <sasha.levin@oracle.com> Cc: Christoph Lameter <cl@linux.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Dave Hansen <dave.hansen@intel.com> Cc: Andi Kleen <andi@firstfloor.org> Cc: Ingo Molnar <mingo@elte.hu> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Christoph Lameter <cl@linux.com> Cc: Pekka Enberg <penberg@kernel.org> Cc: David Rientjes <rientjes@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrey Ryabinin [Fri, 13 Feb 2015 22:39:49 +0000 (14:39 -0800)]
kmemleak: disable kasan instrumentation for kmemleak
kmalloc internally round up allocation size, and kmemleak uses rounded up
size as object's size. This makes kasan to complain while kmemleak scans
memory or calculates of object's checksum. The simplest solution here is
to disable kasan.
Signed-off-by: Andrey Ryabinin <a.ryabinin@samsung.com> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Konstantin Serebryany <kcc@google.com> Cc: Dmitry Chernenkov <dmitryc@google.com> Signed-off-by: Andrey Konovalov <adech.fo@gmail.com> Cc: Yuri Gribov <tetra2005@gmail.com> Cc: Konstantin Khlebnikov <koct9i@gmail.com> Cc: Sasha Levin <sasha.levin@oracle.com> Cc: Christoph Lameter <cl@linux.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Dave Hansen <dave.hansen@intel.com> Cc: Andi Kleen <andi@firstfloor.org> Cc: Ingo Molnar <mingo@elte.hu> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Christoph Lameter <cl@linux.com> Cc: Pekka Enberg <penberg@kernel.org> Cc: David Rientjes <rientjes@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrey Ryabinin [Fri, 13 Feb 2015 22:39:45 +0000 (14:39 -0800)]
fs: dcache: manually unpoison dname after allocation to shut up kasan's reports
We need to manually unpoison rounded up allocation size for dname to avoid
kasan's reports in dentry_string_cmp(). When CONFIG_DCACHE_WORD_ACCESS=y
dentry_string_cmp may access few bytes beyound requested in kmalloc()
size.
dentry_string_cmp() relates on that fact that dentry allocated using
kmalloc and kmalloc internally round up allocation size. So this is not a
bug, but this makes kasan to complain about such accesses. To avoid such
reports we mark rounded up allocation size in shadow as accessible.
Signed-off-by: Andrey Ryabinin <a.ryabinin@samsung.com> Reported-by: Dmitry Vyukov <dvyukov@google.com> Cc: Konstantin Serebryany <kcc@google.com> Cc: Dmitry Chernenkov <dmitryc@google.com> Signed-off-by: Andrey Konovalov <adech.fo@gmail.com> Cc: Yuri Gribov <tetra2005@gmail.com> Cc: Konstantin Khlebnikov <koct9i@gmail.com> Cc: Sasha Levin <sasha.levin@oracle.com> Cc: Christoph Lameter <cl@linux.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Dave Hansen <dave.hansen@intel.com> Cc: Andi Kleen <andi@firstfloor.org> Cc: Ingo Molnar <mingo@elte.hu> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Christoph Lameter <cl@linux.com> Cc: Pekka Enberg <penberg@kernel.org> Cc: David Rientjes <rientjes@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrey Ryabinin [Fri, 13 Feb 2015 22:39:42 +0000 (14:39 -0800)]
mm: slub: add kernel address sanitizer support for slub allocator
With this patch kasan will be able to catch bugs in memory allocated by
slub. Initially all objects in newly allocated slab page, marked as
redzone. Later, when allocation of slub object happens, requested by
caller number of bytes marked as accessible, and the rest of the object
(including slub's metadata) marked as redzone (inaccessible).
We also mark object as accessible if ksize was called for this object.
There is some places in kernel where ksize function is called to inquire
size of really allocated area. Such callers could validly access whole
allocated memory, so it should be marked as accessible.
Code in slub.c and slab_common.c files could validly access to object's
metadata, so instrumentation for this files are disabled.
Signed-off-by: Andrey Ryabinin <a.ryabinin@samsung.com> Signed-off-by: Dmitry Chernenkov <dmitryc@google.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Konstantin Serebryany <kcc@google.com> Signed-off-by: Andrey Konovalov <adech.fo@gmail.com> Cc: Yuri Gribov <tetra2005@gmail.com> Cc: Konstantin Khlebnikov <koct9i@gmail.com> Cc: Sasha Levin <sasha.levin@oracle.com> Cc: Christoph Lameter <cl@linux.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Dave Hansen <dave.hansen@intel.com> Cc: Andi Kleen <andi@firstfloor.org> Cc: Ingo Molnar <mingo@elte.hu> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Christoph Lameter <cl@linux.com> Cc: Pekka Enberg <penberg@kernel.org> Cc: David Rientjes <rientjes@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
projects / mirror_ubuntu-eoan-kernel.git / log