As explained in this discussion:
https://lore.kernel.org/netdev/20210117193009.io3nungdwuzmo5f7@skbuf/
the switchdev notifiers for FDB entries managed to have a zero-day bug.
The bridge would not say that this entry is local:
ip link add br0 type bridge
ip link set swp0 master br0
bridge fdb add dev swp0 00:01:02:03:04:05 master local
and the switchdev driver would be more than happy to offload it as a
normal static FDB entry. This is despite the fact that 'local' and
non-'local' entries have completely opposite directions: a local entry
is locally terminated and not forwarded, whereas a static entry is
forwarded and not locally terminated. So, for example, DSA would install
this entry on swp0 instead of installing it on the CPU port as it should.
There is an even sadder part, which is that the 'local' flag is implicit
if 'static' is not specified, meaning that this command produces the
same result of adding a 'local' entry:
bridge fdb add dev swp0 00:01:02:03:04:05 master
I've updated the man pages for 'bridge', and after reading it now, it
should be pretty clear to any user that the commands above were broken
and should have never resulted in the 00:01:02:03:04:05 address being
forwarded (this behavior is coherent with non-switchdev interfaces):
https://patchwork.kernel.org/project/netdevbpf/cover/20210211104502.2081443-1-olteanv@gmail.com/
If you're a user reading this and this is what you want, just use:
bridge fdb add dev swp0 00:01:02:03:04:05 master static
Because switchdev should have given drivers the means from day one to
classify FDB entries as local/non-local, but didn't, it means that all
drivers are currently broken. So we can just as well omit the switchdev
notifications for local FDB entries, which is exactly what this patch
does to close the bug in stable trees. For further development work
where drivers might want to trap the local FDB entries to the host, we
can add a 'bool is_local' to br_switchdev_fdb_call_notifiers(), and
selectively make drivers act upon that bit, while all the others ignore
those entries if the 'is_local' bit is set.
Fixes: 6b26b51b1d13 ("net: bridge: Add support for notifying devices about FDB add/del") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Fixes off-by-one bugs in the macro assignments for the crashlog control
bits. Was initially tested on emulation but bug revealed after testing on
silicon.
Fixes: 5ef9998c96b0 ("platform/x86: Intel PMT Crashlog capability driver") Signed-off-by: David E. Box <david.e.box@linux.intel.com> Link: https://lore.kernel.org/r/20210317024455.3071477-2-david.e.box@linux.intel.com Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
The debugfs directory '/sys/kernel/debug/energy_model' is needed before
the Energy Model registration can happen. With the recent change in
debugfs subsystem it's not allowed to create this directory at early
stage (core_initcall). Thus creating this directory would fail.
Postpone the creation of the EM debug dir to later stage: fs_initcall.
It should be safe since all clients: CPUFreq drivers, Devfreq drivers
will be initialized in later stages.
The custom debug log below prints the time of creation the EM debug dir
at fs_initcall and successful registration of EMs at later stages.
[ 1.505717] energy_model: creating rootdir
[ 3.698307] cpu cpu0: EM: created perf domain
[ 3.709022] cpu cpu1: EM: created perf domain
Fixes: 56348560d495 ("debugfs: do not attempt to create a new file before the filesystem is initalized") Reported-by: Ionela Voinescu <ionela.voinescu@arm.com> Signed-off-by: Lukasz Luba <lukasz.luba@arm.com> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Setting connection tracking OVS flows and then setting non-CT flows that
use tuple rewrite action (e.g. mod_tp_dst), causes the latter flows not
being offloaded.
Fix by using a stricter condition in modify_header_match_supported() to
check tuple rewrite support only for flows with CT action. The check is
factored out into standalone modify_tuple_supported() function to aid
readability.
Currently, we support hardware offload only for MPLS over UDP.
However, rules matching on MPLS parameters are now wrongly offloaded
for regular MPLS, without actually taking the parameters into
consideration when doing the offload.
Fix it by rejecting such unsupported rules.
Fixes: 72046a91d134 ("net/mlx5e: Allow to match on mpls parameters") Signed-off-by: Alaa Hleihel <alaa@nvidia.com> Reviewed-by: Roi Dayan <roid@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Because the PM-runtime status of the device is not updated in
__rpm_callback(), attempts to suspend the suppliers of the given
device triggered by the rpm_put_suppliers() call in there may
cause a supplier to be suspended completely before the status of
the consumer is updated to RPM_SUSPENDED, which is confusing.
To avoid that (1) modify __rpm_callback() to only decrease the
PM-runtime usage counter of each supplier and (2) make rpm_suspend()
try to suspend the suppliers after changing the consumer's status to
RPM_SUSPENDED, in analogy with the device's parent.
The ppos points to a position in the old kernel memory (and in case of
arm64 in the crash kernel since elfcorehdr is passed as a segment). The
function should update the ppos by the amount that was read. This bug is
not exposed by accident, but other platforms update this value properly.
So, fix it in ARM64 version of elfcorehdr_read() as well.
Signed-off-by: Pavel Tatashin <pasha.tatashin@soleen.com> Fixes: e62aaeac426a ("arm64: kdump: provide /proc/vmcore file") Reviewed-by: Tyler Hicks <tyhicks@linux.microsoft.com> Link: https://lore.kernel.org/r/20210319205054.743368-1-pasha.tatashin@soleen.com Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
When putting iMX5 into suspend, the following flow is
observed:
[ 70.023427] [<c07755f0>] (msm_atomic_commit_tail) from [<c06e7218>]
(commit_tail+0x9c/0x18c)
[ 70.031890] [<c06e7218>] (commit_tail) from [<c0e2920c>]
(drm_atomic_helper_commit+0x1a0/0x1d4)
[ 70.040627] [<c0e2920c>] (drm_atomic_helper_commit) from
[<c06e74d4>] (drm_atomic_helper_disable_all+0x1c4/0x1d4)
[ 70.050913] [<c06e74d4>] (drm_atomic_helper_disable_all) from
[<c0e2943c>] (drm_atomic_helper_suspend+0xb8/0x170)
[ 70.061198] [<c0e2943c>] (drm_atomic_helper_suspend) from
[<c06e84bc>] (drm_mode_config_helper_suspend+0x24/0x58)
In the i.MX5 case, priv->kms is not populated (as i.MX5 does not use any
of the Qualcomm display controllers), causing a NULL pointer
dereference in msm_atomic_commit_tail():
[ 24.268964] 8<--- cut here ---
[ 24.274602] Unable to handle kernel NULL pointer dereference at
virtual address 00000000
[ 24.283434] pgd = (ptrval)
[ 24.286387] [00000000] *pgd=ca212831
[ 24.290788] Internal error: Oops: 17 [#1] SMP ARM
[ 24.295609] Modules linked in:
[ 24.298777] CPU: 0 PID: 197 Comm: init Not tainted 5.11.0-rc2-next-20210111 #333
[ 24.306276] Hardware name: Freescale i.MX53 (Device Tree Support)
[ 24.312442] PC is at msm_atomic_commit_tail+0x54/0xb9c
[ 24.317743] LR is at commit_tail+0xa4/0x1b0
Fix the problem by calling drm_mode_config_helper_suspend/resume()
only when priv->kms is available.
Fixes: ca8199f13498 ("drm/msm/dpu: ensure device suspend happens during PM sleep") Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
If GPU components have failed to bind, shutdown callback would fail with
the following backtrace. Add safeguard check to stop that oops from
happening and allow the board to reboot.
When either the attributes or the password interface is not found, then
unregister the 2 wmi drivers again and return -ENODEV from sysman_init().
Fixes: e8a60aa7404b ("platform/x86: Introduce support for Systems Management Driver over WMI for Dell Systems") Cc: Divya Bharathi <Divya_Bharathi@dell.com> Cc: Mario Limonciello <mario.limonciello@dell.com> Reported-by: Alexander Naumann <alexandernaumann@gmx.de> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20210321115901.35072-7-hdegoede@redhat.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
1. There is no need for the fail_reset_bios and fail_authentication_kset
eror-exit cases, these can be handled by release_attributes_data()
2. Rename all the labels from fail_what_failed, to err_what_to_cleanup
this is the usual way to name these and avoids the need to rename
them when extra steps are added.
Fixes: e8a60aa7404b ("platform/x86: Introduce support for Systems Management Driver over WMI for Dell Systems") Cc: Divya Bharathi <Divya_Bharathi@dell.com> Cc: Mario Limonciello <mario.limonciello@dell.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20210321115901.35072-6-hdegoede@redhat.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
All calls of init_bios_attributes() will result in a
goto fail_create_group if they fail, which calls
release_attributes_data().
So there is no need to call release_attributes_data() from
init_bios_attributes() on failure itself.
Fixes: e8a60aa7404b ("platform/x86: Introduce support for Systems Management Driver over WMI for Dell Systems") Cc: Divya Bharathi <Divya_Bharathi@dell.com> Cc: Mario Limonciello <mario.limonciello@dell.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20210321115901.35072-5-hdegoede@redhat.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
During some of the error-exit paths it is possible that
release_attributes_data() will get called multiple times,
which results in exit_foo_attributes() getting called multiple
times.
Make it safe to call exit_foo_attributes() multiple times,
avoiding double-free()s in this case.
Note that release_attributes_data() really should only be called
once during error-exit paths. This will be fixed in a separate patch
and it is good to have the exit_foo_attributes() functions modified
this way regardless.
Fixes: e8a60aa7404b ("platform/x86: Introduce support for Systems Management Driver over WMI for Dell Systems") Cc: Divya Bharathi <Divya_Bharathi@dell.com> Cc: Mario Limonciello <mario.limonciello@dell.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20210321115901.35072-4-hdegoede@redhat.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
It is possible for release_attributes_data() to get called when the
main_dir_kset has not been created yet, move the removal of the bios-reset
sysfs attr to under a if (main_dir_kset) check to avoid a NULL pointer
deref.
Fixes: e8a60aa7404b ("platform/x86: Introduce support for Systems Management Driver over WMI for Dell Systems") Cc: Divya Bharathi <Divya_Bharathi@dell.com> Cc: Mario Limonciello <mario.limonciello@dell.com> Reported-by: Alexander Naumann <alexandernaumann@gmx.de> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20210321115901.35072-3-hdegoede@redhat.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
On some system the WMI GUIDs used by dell-wmi-sysman are present but there
are no enum type attributes, this causes init_bios_attributes() to return
-ENODEV, after which sysman_init() does a "goto fail_create_group" and then
calls release_attributes_data().
release_attributes_data() calls kset_unregister(wmi_priv.main_dir_kset);
but before this commit it was missing a "wmi_priv.main_dir_kset = NULL;"
statement; and after calling release_attributes_data() the sysman_init()
error handling does this:
if (wmi_priv.main_dir_kset) {
kset_unregister(wmi_priv.main_dir_kset);
wmi_priv.main_dir_kset = NULL;
}
Which causes a second kset_unregister(wmi_priv.main_dir_kset), leading to
a double-free, which causes a crash.
Add the missing "wmi_priv.main_dir_kset = NULL;" statement to
release_attributes_data() to fix this double-free crash.
Fixes: e8a60aa7404b ("platform/x86: Introduce support for Systems Management Driver over WMI for Dell Systems") Cc: Divya Bharathi <Divya_Bharathi@dell.com> Cc: Mario Limonciello <mario.limonciello@dell.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20210321115901.35072-2-hdegoede@redhat.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Commit d4eb538e1f48 ("can: isotp: TX-path: ensure that CAN frame flags are
initialized") ensured the TX flags to be properly set for outgoing CAN
frames.
In fact the root cause of the issue results from a missing initialization
of outgoing CAN frames created by isotp. This is no problem on the CAN bus
as the CAN driver only picks the correctly defined content from the struct
can(fd)_frame. But when the outgoing frames are monitored (e.g. with
candump) we potentially leak some bytes in the unused content of
struct can(fd)_frame.
Fixes: e057dd3fc20f ("can: add ISO 15765-2:2016 transport protocol") Cc: Marc Kleine-Budde <mkl@pengutronix.de> Link: https://lore.kernel.org/r/20210319100619.10858-1-socketcan@hartkopp.net Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
After build with clang -> bpftool btf dump c -> clang/gcc:
./def-clang.h:11:23: error: array has incomplete element type 'struct inner'
struct inner (*ptr_to_array)[2];
Member ptr_to_array of struct outer is a pointer to an array of struct
inner. In the DWARF generated by clang, struct outer appears before
struct inner, so when converting BTF of struct outer into C, bpftool
issues a forward declaration to struct inner. With GCC the DWARF info is
reversed so struct inner gets fully defined.
That forward declaration is not sufficient when compilers handle an
array of the struct, even when it's only used through a pointer. Note
that we can trigger the same issue with an intermediate typedef:
The ECN bit defines ECT(1) = 1, ECT(0) = 2. So inner 0x02 + outer 0x01
should be inner ECT(0) + outer ECT(1). Based on the description of
__INET_ECN_decapsulate, the final decapsulate value should be
ECT(1). So fix the test expect value to 0x01.
Before the fix:
TEST: VXLAN: ECN decap: 01/02->0x02 [FAIL]
Expected to capture 10 packets, got 0.
After the fix:
TEST: VXLAN: ECN decap: 01/02->0x01 [ OK ]
Fixes: a0b61f3d8ebf ("selftests: forwarding: vxlan_bridge_1d: Add an ECN decap test") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
For AF_VSOCK, accept() currently returns sockets that are unlabelled.
Other socket families derive the child's SID from the SID of the parent
and the SID of the incoming packet. This is typically done as the
connected socket is placed in the queue that accept() removes from.
Reuse the existing 'security_sk_clone' hook to copy the SID from the
parent (server) socket to the child. There is no packet SID in this
case.
Fixes: d021c344051a ("VSOCK: Introduce VM Sockets") Signed-off-by: David Brazdil <dbrazdil@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
MTU cannot be changed on dwmac-sun8i. (ip link set eth0 mtu xxx returning EINVAL)
This is due to tx_fifo_size being 0, since this value is used to compute valid
MTU range.
Like dwmac-sunxi (with commit 806fd188ce2a ("net: stmmac: dwmac-sunxi: Provide TX and RX fifo sizes"))
dwmac-sun8i need to have tx and rx fifo sizes set.
I have used values from datasheets.
After this patch, setting a non-default MTU (like 1000) value works and network is still useable.
Tested-on: sun8i-h3-orangepi-pc
Tested-on: sun8i-r40-bananapi-m2-ultra
Tested-on: sun50i-a64-bananapi-m64
Tested-on: sun50i-h5-nanopi-neo-plus2
Tested-on: sun50i-h6-pine-h64 Fixes: 9f93ac8d408 ("net-next: stmmac: Add dwmac-sun8i") Reported-by: Belisko Marek <marek.belisko@gmail.com> Signed-off-by: Corentin Labbe <clabbe@baylibre.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
If the USB host controller is EHCI, the throughput is reduced from
300Mb/s to 60Mb/s, when the rx buffer size is modified from 16K to
32K.
According to the EHCI spec, the maximum size of the qTD is 20K.
Therefore, when the driver uses more than 20K buffer, the latency
time of EHCI would be increased. And, it let the RTL8153A get worse
throughput.
However, the driver uses alloc_pages() for rx buffer, so I limit
the rx buffer to 16K rather than 20K.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=205923 Fixes: ec5791c202ac ("r8152: separate the rx buffer size") Reported-by: Robert Davies <robdavies1977@gmail.com> Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
The sk's sk_route_caps is set in sctp_packet_config, and later it
only needs to change when traversing the transport_list in a loop,
as the dst might be changed in the tx path.
So move sk_route_caps check and set into sctp_outq_flush_transports
from sctp_packet_transmit. This also fixes a dst leak reported by
Chen Yi:
As calling sk_setup_caps() in sctp_packet_transmit may also set the
sk_route_caps for the ctrl sock in a netns. When the netns is being
deleted, the ctrl sock's releasing is later than dst dev's deleting,
which will cause this dev's deleting to hang and dmesg error occurs:
unregister_netdevice: waiting for xxx to become free. Usage count = 1
Reported-by: Chen Yi <yiche@redhat.com> Fixes: bcd623d8e9fa ("sctp: call sk_setup_caps in sctp_packet_transmit instead") Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Add a couple of checks to make sure timestamping is on and that the
timestamp value from DMA is valid. This avoids any functional issues
that could come from a misinterpreted time stamp.
One of the functions changed doesn't need a return value added because
there was no value in checking from the calling locations.
While here, fix a couple of reverse christmas tree issues next to
the code being changed.
Fixes: f56e7bba22fa ("igb: Pull timestamp from fragment before adding it to skb") Fixes: 9cbc948b5a20 ("igb: add XDP support") Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Dave Switzer <david.switzer@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Set the disconnected flag before releasing the data interface in case
netdev registration fails to avoid having the disconnect callback try to
deregister the never registered netdev (and trigger a WARN_ON()).
Fixes: 87cf65601e17 ("USB host CDC Phonet network interface driver") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
__dev_alloc_name(), when supplied with a name containing '%d',
will search for the first available device number to generate a
unique device name.
Since commit ff92741270bf8b6e78aa885f166b68c7a67ab13a ("net:
introduce name_node struct to be used in hashlist") network
devices may have alternate names. __dev_alloc_name() does take
these alternate names into account, possibly generating a name
that is already taken and failing with -ENFILE as a result.
This demonstrates the bug:
# rmmod dummy 2>/dev/null
# ip link property add dev lo altname dummy0
# modprobe dummy numdummies=1
modprobe: ERROR: could not insert 'dummy': Too many open files in system
Instead of creating a device named dummy1, modprobe fails.
Fix this by checking all the names in the d->name_node list, not just d->name.
Signed-off-by: Jiri Bohac <jbohac@suse.cz> Fixes: ff92741270bf ("net: introduce name_node struct to be used in hashlist") Reviewed-by: Jiri Pirko <jiri@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
unmapping npc counter works in a way by traversing all mcam
entries to find which mcam rule is associated with counter.
But loop cursor variable 'entry' is not incremented before
checking next mcam entry which resulting in infinite loop.
This in turn hogs the kworker thread forever and no other
mbox message is processed by AF driver after that.
Fix this by updating entry value before checking next
mcam entry.
Fixes: a958dd59f9ce ("octeontx2-af: Map or unmap NPC MCAM entry and counter") Signed-off-by: Hariprasad Kelam <hkelam@marvell.com> Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
RSS configuration can not be get/set when interface is in down state
as they required mbox communication. RSS enable flag status
is used for set/get configuration. Current code do not clear the
RSS enable flag on interface down which lead to mbox error while
trying to set/get RSS configuration.
Fixes: 85069e95e531 ("octeontx2-pf: Receive side scaling support") Signed-off-by: Geetha sowjanya <gakula@marvell.com> Signed-off-by: Hariprasad Kelam <hkelam@marvell.com> Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Current devlink code try to free already freed irqs as the
irq_allocate flag is not cleared after free leading to kernel
crash while removing rvu driver. The patch fixes the irq free
sequence and clears the irq_allocate flag on free.
Fixes: 7304ac4567bc ("octeontx2-af: Add mailbox IRQ and msg handlers") Signed-off-by: Geetha sowjanya <gakula@marvell.com> Signed-off-by: Hariprasad Kelam <hkelam@marvell.com> Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
The MKEX profile describes what packet fields need to be extracted from
the input packet and how to place those packet fields in the output key
for MCAM matching. The MKEX profile can be in a way where higher layer
packet fields can overwrite lower layer packet fields in output MCAM
Key.
Hence MKEX profile is always ensured that there are no overlaps between
any of the layers. But the commit 42006910b5ea
("octeontx2-af: cleanup KPU config data") introduced TX TOS field which
overlaps with DMAC in MCAM key.
This led to AF driver returning error when TX rule is installed with
DMAC as match criteria since DMAC gets overwritten and cannot be
supported. This patch fixes the issue by removing TOS field from MKEX TX
profile.
Commit 6af1799aaf3f ("ipv6: drop incoming packets having a v4mapped
source address") introduced an input check against v4mapped addresses.
Use of such addresses on the wire is indeed questionable and not
allowed on public Internet. As the commit pointed out
Unfortunately there are applications which use v4mapped addresses,
and breaking them is a clear regression. For example v4mapped
addresses (or any semi-valid addresses, really) may be used
for uni-direction event streams or packet export.
Since the issue which sparked the addition of the check was with
TCP and request_socks in particular push the check down to TCPv6
and DCCP. This restores the ability to receive UDPv6 packets with
v4mapped address as the source.
Keep using the IPSTATS_MIB_INHDRERRORS statistic to minimize the
user-visible changes.
Fixes: 6af1799aaf3f ("ipv6: drop incoming packets having a v4mapped source address") Reported-by: Sunyi Shao <sunyishao@fb.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Acked-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
For NAND Ecc layout, there is a dependency from old kernel's nand driver
setting and current. if old kernel use 4 bit ecc , we should use 4 bit
in new kernel either. else will run into following error at filesystem
mounting.
So, enable fsl,use-minimum-ecc from device tree, to fix this mismatch
[ 9.449265] ubi0: scanning is finished
[ 9.463968] ubi0 warning: ubi_io_read: error -74 (ECC error) while reading
22528 bytes from PEB 513:4096, read only 22528 bytes, retry
[ 9.486940] ubi0 warning: ubi_io_read: error -74 (ECC error) while reading
22528 bytes from PEB 513:4096, read only 22528 bytes, retry
[ 9.509906] ubi0 warning: ubi_io_read: error -74 (ECC error) while reading
22528 bytes from PEB 513:4096, read only 22528 bytes, retry
[ 9.532845] ubi0 error: ubi_io_read: error -74 (ECC error) while reading
22528 bytes from PEB 513:4096, read 22528 bytes
Otherwise, there exists a small window between the opening and closing
of the socket fd where it may leak into processes launched by some other
thread.
Currently flowtable's GC work is initialized as deferrable, which
means GC cannot work on time when system is idle. So the hardware
offloaded flow may be deleted for timeout, since its used time is
not timely updated.
Resolve it by initializing the GC work as delayed work instead of
deferrable.
The ct_state validate should not only check the mask bit and also
check mask_bit & key_bit..
For the +new+est case example, The 'new' and 'est' bits should be
set in both state_mask and state flags. Or the -new-est case also
will be reject by kernel.
When Openvswitch with two flows
ct_state=+trk+new,action=commit,forward
ct_state=+trk+est,action=forward
A packet go through the kernel and the contrack state is invalid,
The ct_state will be +trk-inv. Upcall to the ovs-vswitchd, the
finally dp action will be drop with -new-est+trk.
Fixes: 1bcc51ac0731 ("net/sched: cls_flower: Reject invalid ct_state flags rules") Fixes: 3aed8b63336c ("net/sched: cls_flower: validate ct_state for invalid and reply flags") Signed-off-by: wenxu <wenxu@ucloud.cn> Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
We were linearizing non-TSO skbs that had too many frags, but
we weren't checking number of frags on TSO skbs. This could
lead to a bad page reference when we received a TSO skb with
more frags than the Tx descriptor could support.
v2: use gso_segs rather than yet another division
don't rework the check on the nr_frags
Fixes: 0f3154e6bcb3 ("ionic: Add Tx and Rx handling") Signed-off-by: Shannon Nelson <snelson@pensando.io> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Fix setting min/max DSI PLL rate for the V4.1 7nm DSI PLL (used on
sm8250). Current code checks for pll->type before it is set (as it is
set in the msm_dsi_pll_init() after calling device-specific functions.
Cc: Jonathan Marek <jonathan@marek.ca> Fixes: 1ef7c99d145c ("drm/msm/dsi: add support for 7nm DSI PHY/PLL") Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
The following sequence of commands:
register_ftrace_direct(ip, addr1);
modify_ftrace_direct(ip, addr1, addr2);
unregister_ftrace_direct(ip, addr2);
will cause the kernel to warn:
[ 30.179191] WARNING: CPU: 2 PID: 1961 at kernel/trace/ftrace.c:5223 unregister_ftrace_direct+0x130/0x150
[ 30.180556] CPU: 2 PID: 1961 Comm: test_progs W O 5.12.0-rc2-00378-g86bc10a0a711-dirty #3246
[ 30.182453] RIP: 0010:unregister_ftrace_direct+0x130/0x150
When modify_ftrace_direct() changes the addr from old to new it should update
the addr stored in ftrace_direct_funcs. Otherwise the final
unregister_ftrace_direct() won't find the address and will cause the splat.
pre_tun_rule flows does not follow the usual add-flow path, instead
they are used to update the pre_tun table on the firmware. This means
that if the mask-id gets allocated here the firmware will never see the
"NFP_FL_META_FLAG_MANAGE_MASK" flag for the specific mask id, which
triggers the allocation on the firmware side. This leads to the firmware
mask being corrupted and causing all sorts of strange behaviour.
Fixes: f12725d98cbe ("nfp: flower: offload pre-tunnel rules") Signed-off-by: Louis Peens <louis.peens@corigine.com> Signed-off-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Differentiate between ipv4 and ipv6 flows when configuring the pre_tunnel
table to prevent them trampling each other in the table.
Fixes: 783461604f7e ("nfp: flower: update flow merge code to support IPv6 tunnels") Signed-off-by: Louis Peens <louis.peens@corigine.com> Signed-off-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Fixes: 7f204a7de8b0 ("selftests: net: Add SO_REUSEADDR test to check if 4-tuples are fully utilized.") Signed-off-by: Carlos Llamas <cmllamas@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
We observed some Cisco APs sending the following HE Operation IE in
associate response:
ff 0a 24 f4 3f 00 01 fc ff 00 00 00
Its HE operation parameter is 0x003ff4, so the expected total length is
7 which does not match the actual length = 10. This causes association
failing with "HE AP is missing HE Capability/operation."
According to P802.11ax_D4 Table9-94, HE operation is extensible, and
according to 802.11-2016 10.27.8, STA should discard the part beyond
the maximum length and parse the truncated element.
Allow HE operation element to be longer than expected to handle this
case and future extensions.
Fixes: e4d005b80dee ("mac80211: refactor extended element parsing") Signed-off-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Yen-lin Lai <yenlinlai@chromium.org> Link: https://lore.kernel.org/r/20210223051926.2653301-1-yenlinlai@chromium.org Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Coverity reported the strange "if (~...)" condition that's
always true. It suggested that ! was intended instead of ~,
but upon further analysis I'm convinced that what really was
intended was a comparison to 0xff/0xffff (in HT/VHT cases
respectively), since this indicates that all of the rates
are enabled.
Change the comparison accordingly.
I'm guessing this never really mattered because a reset to
not having a rate mask is basically equivalent to having a
mask that enables all rates.
Reported-by: Colin Ian King <colin.king@canonical.com> Fixes: 2ffbe6d33366 ("mac80211: fix and optimize MCS mask handling") Fixes: b119ad6e726c ("mac80211: add rate mask logic for vht rates") Reviewed-by: Colin Ian King <colin.king@canonical.com> Link: https://lore.kernel.org/r/20210212112213.36b38078f569.I8546a20c80bc1669058eb453e213630b846e107b@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
For M_CAN peripherals, m_can_rx_handler() was called with quota = 1,
which caused any error handling to block RX from taking place until
the next time the IRQ handler is called. This had been observed to
cause RX to be blocked indefinitely in some cases.
This is fixed by calling m_can_rx_handler with a sensibly high quota.
Message loss from RX FIFO 0 is already handled in
m_can_handle_lost_msg(), with netdev output included.
Removing this warning also improves driver performance under heavy
load, where m_can_do_rx_poll() may be called many times before this
interrupt is cleared, causing this message to be output many
times (thanks Mariusz Madej for this report).
There is a UAF in c_can_pci_remove(). dev is released by
free_c_can_dev() and is used by pci_iounmap(pdev, priv->base) later.
To fix this issue, save the mmio address before releasing dev.
Fixes: 5b92da0443c2 ("c_can_pci: generic module for C_CAN/D_CAN on PCI") Link: https://lore.kernel.org/r/20210301024512.539039-1-ztong0001@gmail.com Signed-off-by: Tong Zhang <ztong0001@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Under certain circumstances, when switching from Kvaser's linuxcan driver
(kvpciefd) to the SocketCAN driver (kvaser_pciefd), the bus load reporting
is not disabled.
This is flooding the kernel log with prints like:
[3485.574677] kvaser_pciefd 0000:02:00.0: Received unexpected packet type 0x00000009
Always put the controller in the expected state, instead of assuming that
bus load reporting is inactive.
Note: If bus load reporting is enabled when the driver is loaded, you will
still get a number of bus load packages (and printouts), before it is
disabled.
Fixes: 26ad340e582d ("can: kvaser_pciefd: Add driver for Kvaser PCIEcan devices") Link: https://lore.kernel.org/r/20210309091724.31262-1-jimmyassarsson@gmail.com Signed-off-by: Jimmy Assarsson <extja@kvaser.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
For cases when flexcan is built-in, bitrate is still not set at
registering. So flexcan_chip_freeze() generates:
[ 1.860000] *** ZERO DIVIDE *** FORMAT=4
[ 1.860000] Current process id is 1
[ 1.860000] BAD KERNEL TRAP: 00000000
[ 1.860000] PC: [<402e70c8>] flexcan_chip_freeze+0x1a/0xa8
To allow chip freeze, using an hardcoded timeout when bitrate is still
not set.
Fixes: ec15e27cc890 ("can: flexcan: enable RX FIFO after FRZ/HALT valid") Link: https://lore.kernel.org/r/20210315231510.650593-1-angelo@kernel-space.org Signed-off-by: Angelo Dureghello <angelo@kernel-space.org>
[mkl: use if instead of ? operator] Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Since the peak_usb driver also supports the CAN-USB interfaces
"PCAN-USB X6" and "PCAN-Chip USB" from PEAK-System GmbH, this patch adds
their names to the list of explicitly supported devices.
Fixes: ea8b65b596d7 ("can: usb: Add support of PCAN-Chip USB stamp module") Fixes: f00b534ded60 ("can: peak: Add support for PCAN-USB X6 USB interface") Link: https://lore.kernel.org/r/20210309082128.23125-3-s.grosjean@peak-system.com Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
The previous patch ensures that the TX flags (struct
can_isotp_ll_options::tx_flags) are 0 for classic CAN frames or a user
configured value for CAN-FD frames.
This patch sets the CAN frames flags unconditionally to the ISO-TP TX
flags, so that they are initialized to a proper value. Otherwise when
running "candump -x" on a classical CAN ISO-TP stream shows wrongly
set "B" and "E" flags.
| $ candump any,0:0,#FFFFFFFF -extA
| [...]
| can0 TX B E 713 [8] 2B 0A 0B 0C 0D 0E 0F 00
| can0 TX B E 713 [8] 2C 01 02 03 04 05 06 07
| can0 TX B E 713 [8] 2D 08 09 0A 0B 0C 0D 0E
| can0 TX B E 713 [8] 2E 0F 00 01 02 03 04 05
Fixes: e057dd3fc20f ("can: add ISO 15765-2:2016 transport protocol") Link: https://lore.kernel.org/r/20210218215434.1708249-2-mkl@pengutronix.de Cc: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Currently, Linux computes the HMAC contained in ADD_ADDR sub-option using
the Address Id and the IP Address, and hardcodes a destination port equal
to zero. This is not ok for ADD_ADDR with port: ensure to account for the
endpoint port when computing the HMAC, in compliance with RFC8684 §3.4.1.
Fixes: 22fb85ffaefb ("mptcp: add port support for ADD_ADDR suboption writing") Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Acked-by: Geliang Tang <geliangtang@gmail.com> Signed-off-by: Davide Caratti <dcaratti@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Currently tcp_check_req can be called with obsolete req socket for which big
socket have been already created (because of CPU race or early demux
assigning req socket to multiple packets in gro batch).
Commit e0f9759f530bf789e984 ("tcp: try to keep packet if SYN_RCV race
is lost") added retry in case when tcp_check_req is called for PSH|ACK packet.
But if client sends RST+ACK immediatly after connection being
established (it is performing healthcheck, for example) retry does not
occur. In that case tcp_check_req tries to close req socket,
leaving big socket active.
Fixes: e0f9759f530 ("tcp: try to keep packet if SYN_RCV race is lost") Signed-off-by: Alexander Ovechkin <ovov@yandex-team.ru> Reported-by: Oleg Senin <olegsenin@yandex-team.ru> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
"x25_close" is called by "hdlc_close" in "hdlc.c", which is called by
hardware drivers' "ndo_stop" function.
"x25_xmit" is called by "hdlc_start_xmit" in "hdlc.c", which is hardware
drivers' "ndo_start_xmit" function.
"x25_rx" is called by "hdlc_rcv" in "hdlc.c", which receives HDLC frames
from "net/core/dev.c".
"x25_close" races with "x25_xmit" and "x25_rx" because their callers race.
However, we need to ensure that the LAPB APIs called in "x25_xmit" and
"x25_rx" are called before "lapb_unregister" is called in "x25_close".
This patch adds locking to ensure when "x25_xmit" and "x25_rx" are doing
their work, "lapb_unregister" is not yet called in "x25_close".
Reasons for not solving the racing between "x25_close" and "x25_xmit" by
calling "netif_tx_disable" in "x25_close":
1. We still need to solve the racing between "x25_close" and "x25_rx";
2. The design of the HDLC subsystem assumes the HDLC hardware drivers
have full control over the TX queue, and the HDLC protocol drivers (like
this driver) have no control. Controlling the queue here in the protocol
driver may interfere with hardware drivers' control of the queue.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Xie He <xie.he.0141@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Before this change, the mask is never included in the netlink message, so
"conntrack -E expect" always prints 0.0.0.0.
In older kernels the l3num callback struct was passed as argument, based
on tuple->src.l3num. After the l3num indirection got removed, the call
chain is based on m.src.l3num, but this value is 0xffff.
When fixing the bpf test_tunnel.sh geneve failure. I only fixed the IPv4
part but forgot the IPv6 issue. Similar with the IPv4 fixes 557c223b643a
("selftests/bpf: No need to drop the packet when there is no geneve opt"),
when there is no tunnel option and bpf_skb_get_tunnel_opt() returns error,
there is no need to drop the packets and break all geneve rx traffic.
Just set opt_class to 0 and keep returning TC_ACT_OK at the end.
Fixes: 557c223b643a ("selftests/bpf: No need to drop the packet when there is no geneve opt") Fixes: 933a741e3b82 ("selftests/bpf: bpf tunnel test.") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: William Tu <u9012063@gmail.com> Link: https://lore.kernel.org/bpf/20210309032214.2112438-1-liuhangbin@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
flow_dissector_key_icmp::id is of type u16 (CPU byteorder),
ICMP header has its ID field in network byteorder obviously.
Sparse says:
net/core/flow_dissector.c:178:43: warning: restricted __be16 degrades to integer
Convert ID value to CPU byteorder when storing it into
flow_dissector_key_icmp.
Fixes: 5dec597e5cd0 ("flow_dissector: extract more ICMP information") Signed-off-by: Alexander Lobakin <alobakin@pm.me> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
When a QMI handle is initialized, an array of message handler
structures is provided, defining how any received message should
be handled based on its type and message ID. The QMI core code
traverses this array when a message arrives and calls the function
associated with the (type, msg_id) found in the array.
The array is supposed to be terminated with an empty (all zero)
entry though. Without it, an unsupported message will cause
the QMI core code to go past the end of the array.
Fix this bug, by properly terminating the message handler arrays
provided when QMI handles are set up by the IPA driver.
Fixes: 530f9216a9537 ("soc: qcom: ipa: AP/modem communications") Reported-by: Sujit Kautkar <sujitka@chromium.org> Signed-off-by: Alex Elder <elder@linaro.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
While picking commit a8cd989e1a57 ("mmc: sdhci-msm: Warn about
overclocking SD/MMC") back to my tree I was surprised that it was
reporting warnings. I thought I fixed those! Looking closer at the
fix, I see that I totally bungled it (or at least I halfway bungled
it). The SD card clock got fixed (and that was the one I was really
focused on fixing), but I totally adjusted the wrong clock for eMMC.
Sigh. Let's fix my dumb mistake.
Now both SD and eMMC have floor for the "apps" clock.
This doesn't matter a lot for the final clock rate for HS400 eMMC but
could matter if someone happens to put some slower eMMC on a sc7180.
We also transition through some of these lower rates sometimes and
having them wrong could cause problems during these transitions.
These were the messages I was seeing at boot:
mmc1: Card appears overclocked; req 52000000 Hz, actual 100000000 Hz
mmc1: Card appears overclocked; req 52000000 Hz, actual 100000000 Hz
mmc1: Card appears overclocked; req 104000000 Hz, actual 192000000 Hz
Fixes: 6d37a8d19283 ("clk: qcom: gcc-sc7180: Use floor ops for sdcc clks") Signed-off-by: Douglas Anderson <dianders@chromium.org> Link: https://lore.kernel.org/r/20210224095013.1.I2e2ba4978cfca06520dfb5d757768f9c42140f7c@changeid Reviewed-by: Taniya Das <tdas@codeaurora.org> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
The interrupt handler may set the flag to reset the mac in the future,
but that flag is not cleared once the reset has occurred.
Fixes: 10cbd6407609 ("ftgmac100: Rework NAPI & interrupts handling") Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Reviewed-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Joel Stanley <joel@jms.id.au> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Fix the wrong napi work done reporting in the xsk path of the ice
driver. The code in the main Rx processing loop was written to assume
that the buffer allocation code returns true if all allocations where
successful and false if not. In contrast with all other Intel NIC xsk
drivers, the ice_alloc_rx_bufs_zc() has the inverted logic messing up
the work done reporting in the napi loop.
This can be fixed either by inverting the return value from
ice_alloc_rx_bufs_zc() in the function that uses this in an incorrect
way, or by changing the return value of ice_alloc_rx_bufs_zc(). We
chose the latter as it makes all the xsk allocation functions for
Intel NICs behave in the same way. My guess is that it was this
unexpected discrepancy that gave rise to this bug in the first place.
Fixes: 5bb0c4b5eb61 ("ice, xsk: Move Rx allocation out of while-loop") Reported-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com> Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Per the datasheet, when we clear the power down bit, the PHY remains in
an internal reset state for 40us and then resume normal operation.
Account for that delay to avoid any issues in the future if
genphy_resume() changes.
Fixes: fe26821fa614 ("net: phy: broadcom: Wire suspend/resume for BCM54810") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
In qlcnic_83xx_get_minidump_template, fw_dump->tmpl_hdr was freed by
vfree(). But unfortunately, it is used when extended is true.
Fixes: 7061b2bdd620e ("qlogic: Deletion of unnecessary checks before two function calls") Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
kunit_tool maintains a list of config options which are broken under
UML, which we exclude from an otherwise 'make ARCH=um allyesconfig'
build used to run all tests with the --alltests option.
Something in UML allyesconfig is causing segfaults when page poisining
is enabled (and is poisoning with a non-zero value). Previously, this
didn't occur, as allyesconfig enabled the CONFIG_PAGE_POISONING_ZERO
option, which worked around the problem by zeroing memory. This option
has since been removed, and memory is now poisoned with 0xAA, which
triggers segfaults in many different codepaths, preventing UML from
booting.
Note that we have to disable both CONFIG_PAGE_POISONING and
CONFIG_DEBUG_PAGEALLOC, as the latter will 'select' the former on
architectures (such as UML) which don't implement __kernel_map_pages().
Ideally, we'd fix this properly by tracking down the real root cause,
but since this is breaking KUnit's --alltests feature, it's worth
disabling there in the meantime so the kernel can boot to the point
where tests can actually run.
There is one e1e_wphy() call in e1000_set_d0_lplu_state_82571
that we have caught its return value but lack further handling.
Check and terminate the execution flow just like other e1e_wphy()
in this function.
Fixes: bc7f75fa9788 ("[E1000E]: New pci-express e1000 driver (currently for ICH9 devices only)") Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn> Acked-by: Sasha Neftin <sasha.neftin@intel.com> Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
A possible race condition was found in e1000_reset_task,
after discovering a similar issue in igb driver via
commit 024a8168b749 ("igb: reinit_locked() should be called
with rtnl_lock").
Added rtnl_lock() and rtnl_unlock() to avoid this.
Fixes: bc7f75fa9788 ("[E1000E]: New pci-express e1000 driver (currently for ICH9 devices only)") Suggested-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com> Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
The comment describing the timestamps layout in the packet buffer is
wrong and the code is actually retrieving the timestamp in Timer 1
reference instead of Timer 0. This hasn't been a big issue so far
because hardware is configured to report both timestamps using Timer 0
(see IGC_SRRCTL register configuration in igc_ptp_enable_rx_timestamp()
helper). This patch fixes the comment and the code so we retrieve the
timestamp in Timer 0 reference as expected.
This patch also takes the opportunity to get rid of the hw.mac.type check
since it is not required.
Fixes: 81b055205e8ba ("igc: Add support for RX timestamping") Signed-off-by: Andre Guedes <andre.guedes@intel.com> Signed-off-by: Vedang Patel <vedang.patel@intel.com> Signed-off-by: Jithu Joseph <jithu.joseph@intel.com> Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
The Supported Pause Frame always display "No" even though the Advertised
pause frame showing the correct setting based on the pause parameters via
ethtool. Set bit in link_ksettings to "Supported" for Pause Frame.
Fix Pause Frame Advertising when getting the advertisement via ethtool.
Remove setting the "advertising" bit in link_ksettings during default
case when Tx and Rx are in off state with Auto Negotiate off.
Below is the original output of advertisement link during Tx and Rx off:
Advertised pause frame use: Symmetric Receive-only
Expected output:
Advertised pause frame use: No
Fixes: 8c5ad0dae93c ("igc: Add ethtool support") Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com> Reviewed-by: Malli C <mallikarjuna.chilakala@intel.com> Acked-by: Sasha Neftin <sasha.neftin@intel.com> Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
This commit applies to the igc_reset_task the same changes that
were applied to the igb driver in commit 024a8168b749 ("igb:
reinit_locked() should be called with rtnl_lock")
and fix possible race in reset subtask.
Fixes: 0507ef8a0372 ("igc: Add transmit and receive fastpath and interrupt handlers") Suggested-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Neftin <sasha.neftin@intel.com> Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Similar to commit 92696286f3bb37ba50e4bd8d1beb24afb759a799 ("net:
bcmgenet: Set phydev->dev_flags only for internal PHYs") we need to
qualify the phydev->dev_flags based on whether the port is connected to
an internal or external PHY otherwise we risk having a flags collision
with a completely different interpretation depending on the driver.
Fixes: aa9aef77c761 ("net: dsa: bcm_sf2: communicate integrated PHY revision to PHY driver") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
macvlan_count_rx() can be called from process context, it is thus
necessary to disable preemption before calling u64_stats_update_begin()
syzbot was able to spot this on 32bit arch:
WARNING: CPU: 1 PID: 4632 at include/linux/seqlock.h:271 __seqprop_assert include/linux/seqlock.h:271 [inline]
WARNING: CPU: 1 PID: 4632 at include/linux/seqlock.h:271 __seqprop_assert.constprop.0+0xf0/0x11c include/linux/seqlock.h:269
Modules linked in:
Kernel panic - not syncing: panic_on_warn set ...
CPU: 1 PID: 4632 Comm: kworker/1:3 Not tainted 5.12.0-rc2-syzkaller #0
Hardware name: ARM-Versatile Express
Workqueue: events macvlan_process_broadcast
Backtrace:
[<82740468>] (dump_backtrace) from [<827406dc>] (show_stack+0x18/0x1c arch/arm/kernel/traps.c:252)
r7:00000080 r6:60000093 r5:00000000 r4:8422a3c4
[<827406c4>] (show_stack) from [<82751b58>] (__dump_stack lib/dump_stack.c:79 [inline])
[<827406c4>] (show_stack) from [<82751b58>] (dump_stack+0xb8/0xe8 lib/dump_stack.c:120)
[<82751aa0>] (dump_stack) from [<82741270>] (panic+0x130/0x378 kernel/panic.c:231)
r7:830209b4 r6:84069ea4 r5:00000000 r4:844350d0
[<82741140>] (panic) from [<80244924>] (__warn+0xb0/0x164 kernel/panic.c:605)
r3:8404ec8c r2:00000000 r1:00000000 r0:830209b4
r7:0000010f
[<80244874>] (__warn) from [<82741520>] (warn_slowpath_fmt+0x68/0xd4 kernel/panic.c:628)
r7:81363f70 r6:0000010f r5:83018e50 r4:00000000
[<827414bc>] (warn_slowpath_fmt) from [<81363f70>] (__seqprop_assert include/linux/seqlock.h:271 [inline])
[<827414bc>] (warn_slowpath_fmt) from [<81363f70>] (__seqprop_assert.constprop.0+0xf0/0x11c include/linux/seqlock.h:269)
r8:5a109000 r7:0000000f r6:a568dac0 r5:89802300 r4:00000001
[<81363e80>] (__seqprop_assert.constprop.0) from [<81364af0>] (u64_stats_update_begin include/linux/u64_stats_sync.h:128 [inline])
[<81363e80>] (__seqprop_assert.constprop.0) from [<81364af0>] (macvlan_count_rx include/linux/if_macvlan.h:47 [inline])
[<81363e80>] (__seqprop_assert.constprop.0) from [<81364af0>] (macvlan_broadcast+0x154/0x26c drivers/net/macvlan.c:291)
r5:89802300 r4:8a927740
[<8136499c>] (macvlan_broadcast) from [<81365020>] (macvlan_process_broadcast+0x258/0x2d0 drivers/net/macvlan.c:317)
r10:81364f78 r9:8a86d000 r8:8a9c7e7c r7:8413aa5c r6:00000000 r5:00000000
r4:89802840
[<81364dc8>] (macvlan_process_broadcast) from [<802696a4>] (process_one_work+0x2d4/0x998 kernel/workqueue.c:2275)
r10:00000008 r9:8404ec98 r8:84367a02 r7:ddfe6400 r6:ddfe2d40 r5:898dac80
r4:8a86d43c
[<802693d0>] (process_one_work) from [<80269dcc>] (worker_thread+0x64/0x54c kernel/workqueue.c:2421)
r10:00000008 r9:8a9c6000 r8:84006d00 r7:ddfe2d78 r6:898dac94 r5:ddfe2d40
r4:898dac80
[<80269d68>] (worker_thread) from [<80271f40>] (kthread+0x184/0x1a4 kernel/kthread.c:292)
r10:85247e64 r9:898dac80 r8:80269d68 r7:00000000 r6:8a9c6000 r5:89a2ee40
r4:8a97bd00
[<80271dbc>] (kthread) from [<80200114>] (ret_from_fork+0x14/0x20 arch/arm/kernel/entry-common.S:158)
Exception stack(0x8a9c7fb0 to 0x8a9c7ff8)
Fixes: 412ca1550cbe ("macvlan: Move broadcasts into a work queue") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Herbert Xu <herbert@gondor.apana.org.au> Reported-by: syzbot <syzkaller@googlegroups.com> Acked-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
In the rare case that drop_monitor fails to register its probe on the
'napi_poll' tracepoint, it will not deactivate its hysteresis timer as
part of the error path. If the hysteresis timer was armed by the shortly
lived 'kfree_skb' probe and user space retries to initiate tracing, a
warning will be emitted for trying to initialize an active object [1].
Fix this by properly undoing all the operations that were done prior to
probe registration, in both software and hardware code paths.
Note that syzkaller managed to fail probe registration by injecting a
slab allocation failure [2].
Syzbot reported the suspecious RCU usage in nexthop_fib6_nh() when
called from ipv6_route_seq_show(). The reason is ipv6_route_seq_start()
calls rcu_read_lock_bh(), while nexthop_fib6_nh() calls
rcu_dereference_rtnl().
The fix proposed is to add a variant of nexthop_fib6_nh() to use
rcu_dereference_bh_rtnl() for ipv6_route_seq_show().
The reported trace is as follows:
./include/net/nexthop.h:416 suspicious rcu_dereference_check() usage!
Fixes: f88d8ea67fbdb ("ipv6: Plumb support for nexthop object in a fib6_info") Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: Wei Wang <weiwan@google.com> Cc: David Ahern <dsahern@kernel.org> Cc: Ido Schimmel <idosch@idosch.org> Cc: Petr Machata <petrm@nvidia.com> Cc: Eric Dumazet <edumazet@google.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: David Ahern <dsahern@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
The cited change added offload support for Geneve options without verifying
the validity of the options masks, this caused offload of rules with match
on Geneve options with class,type and data masks which are zero to fail.
Fix by ignoring the match on Geneve options in case option masks are
all zero.
Fixes: 9272e3df3023 ("net/mlx5e: Geneve, Add support for encap/decap flows offload") Signed-off-by: Maor Dickman <maord@nvidia.com> Reviewed-by: Roi Dayan <roid@nvidia.com> Reviewed-by: Oz Shlomo <ozsh@nvidia.com> Reviewed-by: Yevgeny Kliteynik <kliteyn@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Port timestamping for PTP can be enabled/disabled while the channels are
closed. In that case mlx5e_safe_switch_channels is skipped, and the
preactivate hook is called directly. However, if that hook returns an
error, the channel parameters must be reverted back to their old values.
This commit adds missing handling on this case.
Each RQ (including XSK RQs) takes a reference to the XDP program. When
an XDP program is attached or detached, the channels and queues are
recreated, however, there is a special flow for changing an active XDP
program to another one. In that flow, channels and queues stay alive,
but the refcounts of the old and new XDP programs are adjusted. This
flow didn't increment refcount by the number of active XSK RQs, and this
commit fixes it.
When closing the PTP channel, set its pointer explicitly to NULL. PTP
channel is opened on demand, the code verify the pointer validity before
access. Nullify it when closing the PTP channel to avoid unexpected
behavior.
Since cited patch, MLX5E_REQUIRED_WQE_MTTS is not a power of two.
Hence, usage of MLX5E_LOG_ALIGNED_MPWQE_PPW should be replaced,
as it lost some accuracy. Use the designated macro to calculate
the number of required MTTs.
This makes sure the solution in cited patch works properly.
While here, un-inline mlx5e_get_mpwqe_offset(), and remove the
unused RQ parameter.
Fixes: c3c9402373fe ("net/mlx5e: Add resiliency in Striding RQ mode for packets larger than MTU") Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
It was reported ([0]) that having optional -m flag between source and
destination arguments in install command breaks bpftools cross-build
on MacOS. Move -m to the front to fix this issue.
[0] https://github.com/openwrt/openwrt/pull/3959
Fixes: 7110d80d53f4 ("libbpf: Makefile set specified permission mode") Signed-off-by: Georgi Valkov <gvalkov@abv.bg> Signed-off-by: Andrii Nakryiko <andrii@kernel.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/bpf/20210308183038.613432-1-andrii@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
bpf_fd_inode_storage_lookup_elem() returned NULL when getting a bad FD,
which caused -ENOENT in bpf_map_copy_value. -EBADF error is better than
-ENOENT for a bad FD behaviour.
The patch was partially contributed by CyberArk Software, Inc.
Fixes: 8ea636848aca ("bpf: Implement bpf_local_storage for inodes") Signed-off-by: Tal Lossos <tallossos@gmail.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Yonghong Song <yhs@fb.com> Acked-by: KP Singh <kpsingh@kernel.org> Link: https://lore.kernel.org/bpf/20210307120948.61414-1-tallossos@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
The syzbot got FD of vmlinux BTF and passed it into map_create which caused
crash in btf_type_id_size() when it tried to access resolved_ids. The vmlinux
BTF doesn't have 'resolved_ids' and 'resolved_sizes' initialized to save
memory. To avoid such issues disallow using vmlinux BTF in prog_load and
map_create commands.
Fixes: 5329722057d4 ("bpf: Assign ID to vmlinux BTF and return extra info for BTF in GET_OBJ_INFO") Reported-by: syzbot+8bab8ed346746e7540e8@syzkaller.appspotmail.com Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Yonghong Song <yhs@fb.com> Link: https://lore.kernel.org/bpf/20210307225248.79031-1-alexei.starovoitov@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Currently, veth_xmit() would call the skb_record_rx_queue() only when
there is XDP program loaded on peer interface in native mode.
If peer has XDP prog in generic mode, then netif_receive_generic_xdp()
has a call to netif_get_rxqueue(skb), so for multi-queue veth it will
not be possible to grab a correct rxq.
To fix that, store queue_mapping independently of XDP prog presence on
peer interface.
Fixes: 638264dc9022 ("veth: Support per queue XDP ring") Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Toshiaki Makita <toshiaki.makita1@gmail.com> Link: https://lore.kernel.org/bpf/20210303152903.11172-1-maciej.fijalkowski@intel.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
On reset deassert, we must wait a bit after the rstst bit change before
we allow clockdomain autoidle again. Otherwise we get the following oops
sometimes on dra7 with iva:
Unhandled fault: imprecise external abort (0x1406) at 0x00000000 44000000.ocp:L3 Standard Error: MASTER MPU TARGET IVA_CONFIG (Read Link):
At Address: 0x0005A410 : Data Access in User mode during Functional access
Internal error: : 1406 [#1] SMP ARM
...
(sysc_write_sysconfig) from [<c0782cb0>] (sysc_enable_module+0xcc/0x260)
(sysc_enable_module) from [<c0782f0c>] (sysc_runtime_resume+0xc8/0x174)
(sysc_runtime_resume) from [<c0a3e1ac>] (genpd_runtime_resume+0x94/0x224)
(genpd_runtime_resume) from [<c0a33f0c>] (__rpm_callback+0xd8/0x180)
It is unclear what all devices this might affect, but presumably other
devices with the rstst bit too can be affected. So let's just enable the
delay for all the devices with rstst bit for now. Later on we may want to
limit the list to the know affected devices if needed.
Fixes: d30cd83f6853 ("soc: ti: omap-prm: add support for denying idle for reset clockdomain") Reported-by: Yongqin Liu <yongqin.liu@linaro.org> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
When I dropped legacy data for omap4 and dra7 smartreflex in favor of
device tree based data, it seems I only testd for the "SmartReflex Class3
initialized" line in dmesg. I missed the fact that there is also
omap_devinit_smartreflex() that happens later, and now it produces an
error on boot for "No Voltage table for the corresponding vdd. Cannot
create debugfs entries for n-values".
This happens as we no longer have the smartreflex instance legacy data,
and have not yet moved completely to device tree based booting for the
driver. Let's fix the issue by changing the smartreflex init to use names.
This should all eventually go away in favor of doing the init in the
driver based on devicetree compatible value.
Note that dra7xx_init_early() is not calling any voltage domain init like
omap54xx_voltagedomains_init(), or a dra7 specific voltagedomains init.
This means that on dra7 smartreflex is still not fully initialized, and
also seems to be missing the related devicetree nodes.
Fixes: a6b1e717e942 ("ARM: OMAP2+: Drop legacy platform data for omap4 smartreflex") Fixes: e54740b4afe8 ("ARM: OMAP2+: Drop legacy platform data for dra7 smartreflex") Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
projects / mirror_ubuntu-hirsute-kernel.git / log