Fix spelling mistakes in rx stats text. I missed these from an earlier
round of fixing the same spelling mistake.
Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Mukesh Ojha <mojha@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Tamás Szűcs [Sun, 14 Apr 2019 18:36:41 +0000 (20:36 +0200)]
mwifiex: add support for SD8987 chipset
This patch adds support for Marvell 88W8987 chipset with SDIO interface.
Register offsets and supported feature flags are updated. The corresponding
firmware image file shall be "mrvl/sd8987_uapsta.bin".
Signed-off-by: Tamás Szűcs <tszucs@protonmail.ch> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Petr Štetiar [Thu, 11 Apr 2019 18:13:30 +0000 (20:13 +0200)]
mwl8k: Fix rate_idx underflow
It was reported on OpenWrt bug tracking system[1], that several users
are affected by the endless reboot of their routers if they configure
5GHz interface with channel 44 or 48.
The reboot loop is caused by the following excessive number of WARN_ON
messages:
WARNING: CPU: 0 PID: 0 at backports-4.19.23-1/net/mac80211/rx.c:4516
ieee80211_rx_napi+0x1fc/0xa54 [mac80211]
as the messages are being correctly emitted by the following guard:
case RX_ENC_LEGACY:
if (WARN_ON(status->rate_idx >= sband->n_bitrates))
as the rate_idx is in this case erroneously set to 251 (0xfb). This fix
simply converts previously used magic number to proper constant and
guards against substraction which is leading to the currently observed
underflow.
Fixes: 854783444bab ("mwl8k: properly set receive status rate index on 5 GHz receive") Cc: <stable@vger.kernel.org> Tested-by: Eubert Bao <bunnier@gmail.com> Reported-by: Eubert Bao <bunnier@gmail.com> Signed-off-by: Petr Štetiar <ynezz@true.cz> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Larry Finger [Thu, 4 Apr 2019 18:49:14 +0000 (13:49 -0500)]
b43: Remove empty function lpphy_papd_cal()
In commit d825db346270e ("b43: shut up clang -Wuninitialized variable
warning"), the message noted that function lpphy_papd_cal() was empty
and had an old TODO regarding its implementation. As the reverse
engineering project that created the LP-PHY version of this driver
has not been active for some time, it is safe to remove this empty
function.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Dan Carpenter [Thu, 4 Apr 2019 08:44:23 +0000 (11:44 +0300)]
mwifiex: prevent an array overflow
The "rate_index" is only used as an index into the phist_data->rx_rate[]
array in the mwifiex_hist_data_set() function. That array has
MWIFIEX_MAX_AC_RX_RATES (74) elements and it's used to generate some
debugfs information. The "rate_index" variable comes from the network
skb->data[] and it is a u8 so it's in the 0-255 range. We need to cap
it to prevent an array overflow.
Fixes: cbf6e05527a7 ("mwifiex: add rx histogram statistics support") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes, in particular in the
context in which this code is being used.
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
Below changes are done:
* Device 80MHz clock should be disabled for 9116 in 20MHz band.
* Default edca parameters should be used initially before
connection.
* Default TA aggregation is 3 for 9116.
* Bootup parameters should be loaded first when channel is
changed.
* 4 byte register writes are possible for 9116.
Signed-off-by: Siva Rebbagondla <siva8118@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
rsi: change in device init frame sequence for 9116
Initial frame exchange sequence has been changed for 9116 chip. Getting MAC
address using EEPROM read frame will be once common device configuration is
done and RESET_MAC frame is sending after bootup parameters confirmation is
received, which are different from RS9113 device
Signed-off-by: Siva Rebbagondla <siva8118@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
rsi: move common part of firmware load to separate function
Till software bootloader ready state, communication with device is common
for 9113 and 9116. Hence moved that part of firmware loading to separate
function rsi_prepare_fw_load(). Also LMAC_VER_OFFSET is different for 9113
and 9116, so renamed existing macro to LMAC_VER_OFFSET_9113
Signed-off-by: Siva Rebbagondla <siva8118@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
9116 device id entry is added in both SDIO and USB interfaces.
New enumberation value taken for the device model. Based on the
device model detected run time, few device specific operations
needs to be performed.
adding rsi_dev_model to get device type in run time, as we can use
same driver for 9113 and 9116 except few firmware load changes.
Signed-off-by: Siva Rebbagondla <siva8118@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
rt2800mmio: use timer and work for handling tx statuses timeouts
Sometimes we can get into situation when there are pending statuses,
but we do not get INT_SOURCE_CSR_TX_FIFO_STATUS. Handle this situation
by arming timeout timer and read statuses (it will fix case when
we just do not have irq) and queue work to handle case we missed
statues from hardware FIFO.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
rt2800: partially restore old mmio txstatus behaviour
Do not disable txstatus interrupt and add quota of processed tx statuses in
one tasklet. Quota is needed to allow to fed device with new frames during
processing of tx statuses.
Patch fixes about 15% performance degradation on some scenarios caused by 0b0d556e0ebb ("rt2800mmio: use txdone/txstatus routines from lib").
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Aditya Pakki [Sat, 23 Mar 2019 20:49:16 +0000 (15:49 -0500)]
rsi: Fix NULL pointer dereference in kmalloc
kmalloc can fail in rsi_register_rates_channels but memcpy still attempts
to write to channels. The patch replaces these calls with kmemdup and
passes the error upstream.
Signed-off-by: Aditya Pakki <pakki001@umn.edu> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For unknown reasons printk() on some context can cause CPU hung on
embedded MT7620 AP/router MIPS platforms. What can result on wifi
disconnects.
This patch move queue full messages to debug level what is consistent
with other mac80211 drivers which drop packet silently if tx queue is
full. This make MT7620 OpenWRT routers more stable, what was reported
by various users.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some USB host devices/drivers on some conditions can always return
EPROTO error on submitted URBs. That can cause infinity loop in the
rt2x00 driver.
Since we can have single EPROTO errors we can not mark as device as
removed to avoid infinity loop. However we can count consecutive
EPROTO errors and mark device as removed if get lot of it.
I choose number 10 as threshold.
Reported-and-tested-by: Randy Oostdyk <linux-kernel@oostdyk.com> Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As reported by Randy we can overwhelm logs on some USB error conditions.
To avoid that use dev_warn_ratelimited() and dev_err_ratelimitd().
Reported-and-tested-by: Randy Oostdyk <linux-kernel@oostdyk.com> Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In ssb_modinit, it does not fail SSB init when ssb_host_pcmcia_init failed,
however in ssb_modexit, ssb_host_pcmcia_exit calls pcmcia_unregister_driver
unconditionally, which may tigger a NULL pointer dereference issue as above.
Reported-by: Hulk Robot <hulkci@huawei.com> Fixes: 399500da18f7 ("ssb: pick PCMCIA host code support from b43 driver") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes, in particular in the
context in which this code is being used.
Kalle Valo [Thu, 25 Apr 2019 15:26:23 +0000 (18:26 +0300)]
Merge tag 'iwlwifi-next-for-kalle-2019-04-18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
Third batch of patches intended for v5.2
* Bump the 20000-series FW API version supported;
* Work on the new debugging infra continues;
* One clean-up to prevent a bogus warning with clang;
* A small cleanup in the PCI ID list;
* Work on new hardware continues;
* RTT confidence indication support for FTM;
* An improvement in HE rate-scaling;
iwlwifi: dbg_ini: set dump bit only when trigger collection is certain
In case the the trigger occurrences is zero or force_restart is set, the
driver sets IWL_FWRT_STATUS_DUMPING without actually scheduling trigger
collection. At this point no other dump collection can be performed.
Solve this by setting IWL_FWRT_STATUS_DUMPING bit only when the driver
is surely going to schedule dump collection
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
iwlwifi: mvm: Change an 'else if' into an 'else' in iwl_mvm_send_add_bcast_sta
When building with -Wsometimes-uninitialized, Clang warns:
drivers/net/wireless/intel/iwlwifi/mvm/sta.c:2114:12: warning: variable
'queue' is used uninitialized whenever 'if' condition is false
[-Wsometimes-uninitialized]
Clang can't evaluate at this point that WARN(1, ...) always returns true
because __ret_warn_on is defined as !!(condition), which isn't
immediately evaluated as 1. Change this branch to else so that it's
clear to Clang that we intend to bail out here.
Avraham Stern [Mon, 25 Feb 2019 13:12:26 +0000 (15:12 +0200)]
iwlwifi: mvm: support rtt confidence indication
The range response notification API has changed to add a value that
indicates the confidence of the rtt result.
Support the new API and print the rtt confidence for debug.
iwlwifi: dbg_ini: support notification and dhc regions type parsing
IWL_FW_INI_REGION_CSR and IWL_FW_INI_REGION_NOTIFICATION does not have
memory addresses attached to them so the driver should skip them when
parsing the region tlv.
Also, instead of declearing what region types should skip the addition of
the memory addresses, declare what regions have addition of memory
addresses.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Shaul Triebitz [Thu, 28 Feb 2019 15:17:58 +0000 (17:17 +0200)]
iwlwifi: mvm: set 512 TX queue slots for AX210 devices
AX210 devices support 256 BA (256 MPDUs in an AMPDU).
The firmware requires that the number of TFDs will be
minimum twice as big as the BA size (2 * 256 = 512).
This patchset adds support for a PHY reset driven by a reset-controller.
Currently, only GPIO driven resets are supported by the PHY subsystem.
It also renames the reset-gpio from 'reset' to 'reset_gpio' to
better differentiate between resets wired to a GPIO and resets wired to
a reset-controller driven pin.
Some systems have the PHY reset-line wired to a pin controlled by a
reset-controller (eg. some Atheros AR9132 based boards). In case the
bootloader asserts reset before loading the kernel, we currently do not
have a clean way of deasserting reset to probe the PHY.
v3:
- add missing newline in mdio_bus.c
v2:
- fixed missed rename of "reset" in at803x.c
- move initial reset to mdio_device_reset
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Wed, 17 Apr 2019 20:51:59 +0000 (13:51 -0700)]
net: skb: remove unused asserts
We are discouraging the use of BUG() these days, remove the
unused ASSERT macros from skbuff.h.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Wed, 17 Apr 2019 20:51:58 +0000 (13:51 -0700)]
net: gemini: remove unnecessary assert
The driver does not advertize NETIF_F_FRAGLIST, the stack can't
pass skbs with frags lists to the xmit function.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Wed, 17 Apr 2019 20:51:57 +0000 (13:51 -0700)]
net/sched: taprio: fix build without 64bit div
Recent changes to taprio did not use the correct div64 helpers,
leading to:
net/sched/sch_taprio.o: In function `taprio_dequeue':
sch_taprio.c:(.text+0x34a): undefined reference to `__divdi3'
net/sched/sch_taprio.o: In function `advance_sched':
sch_taprio.c:(.text+0xa0b): undefined reference to `__divdi3'
net/sched/sch_taprio.o: In function `taprio_init':
sch_taprio.c:(.text+0x1450): undefined reference to `__divdi3'
/home/jkicinski/devel/linux/Makefile:1032: recipe for target 'vmlinux' failed
Use math64 helpers.
Fixes: 7b9eba7ba0c1 ("net/sched: taprio: fix picos_per_byte miscalculation") Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com> Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Wed, 17 Apr 2019 20:51:56 +0000 (13:51 -0700)]
sb1000: fix variable set but not used warnings
GCC 8 complains:
drivers/net/sb1000.c: In function ‘card_send_command’:
drivers/net/sb1000.c:319:14: warning: variable ‘x’ set but not used [-Wunused-but-set-variable]
int status, x;
^
drivers/net/sb1000.c: In function ‘sb1000_check_CRC’:
drivers/net/sb1000.c:493:6: warning: variable ‘crc’ set but not used [-Wunused-but-set-variable]
int crc, status;
^~~
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Wed, 17 Apr 2019 20:51:55 +0000 (13:51 -0700)]
l2tp: fix set but not used variable
GCC complains:
net/l2tp/l2tp_ppp.c: In function ‘pppol2tp_ioctl’:
net/l2tp/l2tp_ppp.c:1073:6: warning: variable ‘val’ set but not used [-Wunused-but-set-variable]
int val;
^~~
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
To make ICMPv6 closer to ICMPv4, add ratemask parameter. Since the ICMP
message types use larger numeric values, a simple bitmask doesn't fit.
I use large bitmap. The input and output are the in form of list of
ranges. Set the default to rate limit all error messages but Packet Too
Big. For Packet Too Big, use ratemask instead of hard-coded.
There are functions where icmpv6_xrlim_allow() and icmpv6_global_allow()
aren't called. This patch only adds them to icmpv6_echo_reply().
Rate limiting error messages is mandated by RFC 4443 but RFC 4890 says
that it is also acceptable to rate limit informational messages. Thus,
I removed the current hard-coded behavior of icmpv6_mask_allow() that
doesn't rate limit informational messages.
v2: Add dummy function proc_do_large_bitmap() if CONFIG_PROC_SYSCTL
isn't defined, expand the description in ip-sysctl.txt and remove
unnecessary conditional before kfree().
v3: Inline the bitmap instead of dynamically allocated. Still is a
pointer to it is needed because of the way proc_do_large_bitmap work.
Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
In phy_device_create() we set phydev->autoneg = 1. This isn't changed
even if the PHY doesn't support autoneg. This seems to affect very
few PHY's, and they disable phydev->autoneg in their config_init
callback. So it's more of an improvement, therefore net-next.
The patch also wouldn't apply to older kernel versions because the
link mode bitmaps have been introduced recently.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 18 Apr 2019 18:25:33 +0000 (11:25 -0700)]
Merge branch '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2019-04-18
This series contains updates to the ice driver only.
Anirudh fixes up code comments which had typos. Added support for DCB
into the ice driver, which required a bit of refactoring of the existing
code. Also fixed a potential race condition between closing and opening
the VSI for a MIB change event, so resolved this by grabbing the
rtnl_lock prior to closing. Added support to process LLDP MIB change
notifications. Added support for reporting DCB stats via ethtool.
Brett updates the calculation to increment ITR to use a direct
calculation instead of using estimations. This provides a more accurate
value.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Brett Creeley [Thu, 28 Feb 2019 23:25:47 +0000 (15:25 -0800)]
ice: Calculate ITR increment based on direct calculation
Currently when calculating how much to increment ITR by inside of
ice_update_itr() we do some estimations and intermediate
calculations. Instead of doing estimations, just do the
calculation directly. This allows for a more accurate value and it
makes it easier for the next person to understand and update.
Also, remove the dividing the ITR value by 2 when latency
driven because the ITR values are already so low for 100Gbps
speed. This should help get to the desired ITR value faster.
Signed-off-by: Brett Creeley <brett.creeley@intel.com> Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a new function ice_pf_dcb_cfg (and related helpers)
which applies the DCB configuration obtained from the firmware. As
part of this, VSIs/netdevs are updated with traffic class information.
This patch requires a bit of a refactor of existing code.
1. For a MIB change event, the associated VSI is closed and brought up
again. The gap between closing and opening the VSI can cause a race
condition. Fix this by grabbing the rtnl_lock prior to closing the
VSI and then only free it after re-opening the VSI during a MIB
change event.
2. ice_sched_query_elem is used in ice_sched.c and with this patch, in
ice_dcb.c as well. However, ice_dcb.c is not built when CONFIG_DCB is
unset. This results in namespace warnings (ice_sched.o: Externally
defined symbols with no external references) when CONFIG_DCB is unset.
To avoid this move ice_sched_query_elem from ice_sched.c to
ice_common.c.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch introduces a new top level function ice_init_dcb (and
related lower level helper functions) which continues the DCB init
flow.
This function uses ice_get_dcb_cfg to get, parse and store the DCB
configuration. Once this is done, it sets itself up to be notified
by the firmware on LLDP MIB change events.
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch introduces a skeleton for ice_init_pf_dcb, the top level
function for DCB initialization. Subsequent patches will add to this
DCB init flow.
In this patch, ice_init_pf_dcb checks if DCB is a supported capability.
If so, an admin queue call to start the LLDP and DCBx in firmware is
issued. If not, an error is reported. Note that we don't fail the driver
init if DCB init fails.
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Capitalize abbreviations and spell out some that aren't obvious.
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Larry Finger [Wed, 17 Apr 2019 00:35:47 +0000 (19:35 -0500)]
rtlwifi: rtl8188ee: Remove extraneous file
Somehow file drivers/net/wireless/realtek/rtlwifi/rtl8188ee/trx.c.rej was
incorporated into the sources. Obviously, it can be removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Reported-by: Andrew Morton <akpm@linux-foundation.org> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
David Ahern [Wed, 17 Apr 2019 00:31:43 +0000 (17:31 -0700)]
net ipv6: Prevent neighbor add if protocol is disabled on device
Disabling IPv6 on an interface removes existing entries but nothing prevents
new entries from being manually added. To that end, add a new neigh_table
operation, allow_add, that is called on RTM_NEWNEIGH to see if neighbor
entries are allowed on a given device. If IPv6 is disabled on the device,
allow_add returns false and passes a message back to the user via extack.
$ echo 1 > /proc/sys/net/ipv6/conf/eth1/disable_ipv6
$ ip -6 neigh add fe80::4c88:bff:fe21:2704 dev eth1 lladdr de:ad:be:ef:01:01
Error: IPv6 is disabled on this device.
Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
ipv6: Use fib6_result for fib_lookups
Add fib6_result as a single data structure to hold results from a fib
lookup. IPv6 currently has everything in 1 data structure - a fib6_info,
but with nexthop objects the fib6_nh can be in a nexthop or a nexthop
can be a blackhole which affects the fib6_type and flags (REJECT).
v2
- fixed 2 bugs in patch12:
i. checking return from fib6_table_lookup in fib6_lookup
ii. call to fib6_rule_saddr in fib6_rule_action_alt should use res->nh
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Tue, 16 Apr 2019 21:36:11 +0000 (14:36 -0700)]
ipv6: Add fib6_type and fib6_flags to fib6_result
Add the fib6_flags and fib6_type to fib6_result. Update the lookup helpers
to set them and update post fib lookup users to use the version from the
result.
This allows nexthop objects to have blackhole nexthop.
Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Tue, 16 Apr 2019 21:36:05 +0000 (14:36 -0700)]
ipv6: Pass fib6_result to rt6_insert_exception
Update rt6_insert_exception to take a fib6_result over a fib6_info.
Change ort to f6i from the fib6_result and rename to better reflect
what it references (a fib6_info).
Since this function is already getting changed, update the comments
to reference fib6_info variables rather than the older rt6_info.
Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Tue, 16 Apr 2019 21:36:00 +0000 (14:36 -0700)]
ipv6: Pass fib6_result to rt6_find_cached_rt
Simplify rt6_find_cached_rt for the fast path cases and pass fib6_result
to rt6_find_cached_rt. Rename the local return variable to ret to maintain
consisting with fib6_result name.
Update the comment in rt6_find_cached_rt to reference the new names in
a fib6_info vs the old name when fib entries were an rt6_info.
Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Tue, 16 Apr 2019 21:35:59 +0000 (14:35 -0700)]
ipv6: Rename fib6_multipath_select and pass fib6_result
Add 'struct fib6_result' to hold the fib entry and fib6_nh from a fib
lookup as separate entries, similar to what IPv4 now has with fib_result.
Rename fib6_multipath_select to fib6_select_path, pass fib6_result to
it, and set f6i and nh in the result once a path selection is done.
Call fib6_select_path unconditionally for path selection which means
moving the sibling and oif check to fib6_select_path. To handle the two
different call paths (2 only call multipath_select if flowi6_oif == 0 and
the other always calls it), add a new have_oif_match that controls the
sibling walk if relevant.
Update callers of fib6_multipath_select accordingly and have them use the
fib6_info and fib6_nh from the result.
This is needed for multipath nexthop objects where a single f6i can
point to multiple fib6_nh (similar to IPv4).
Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
s390/qeth: stop/wake TX queues based on their fill level
Current xmit code only stops the txq after attempting to fill an
IO buffer that hasn't been TX-completed yet. In many-connection
scenarios, this can result in frequent rejected TX attempts, requeuing
of skbs with NETDEV_TX_BUSY and extra overhead.
Now that we have a proper 1-to-1 relation between stack-side txqs and
our HW Queues, overhaul the stop/wake logic so that the xmit code
stops the txq as needed.
Given that we might map multiple skbs into a single buffer, it's crucial
to ensure that the queue always provides an _entirely_ empty IO buffer.
Otherwise large skbs (eg TSO) might not fit into the last available
buffer. So whenever qeth_do_send_packet() first utilizes an _empty_
buffer, it updates & checks the used_buffers count.
This now ensures that an skb passed to qeth_xmit() can always be mapped
into an IO buffer, so remove all of the -EBUSY roll-back handling in the
TX path. We preserve the minimal safety-checks ("Is this IO buffer
really available?"), just in case some nasty future bug ever attempts to
corrupt an in-use buffer.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / mirror_ubuntu-hirsute-kernel.git / log