ACPI / PM: Do not disable wakeup GPEs that have not been enabled
In some cases acpi_device_wakeup() may be called to ensure wakeup
power to be off for a given device even though that device's wakeup
GPE has not been enabled so far. It calls acpi_disable_gpe() on a
GPE that's not enabled and this causes ACPICA to return the AE_LIMIT
status code from that call which then is reported as an error by the
ACPICA's debug facilities (if enabled). This may lead to a fair
amount of confusion, so introduce a new ACPI device wakeup flag
to store the wakeup GPE status and avoid disabling wakeup GPEs
that have not been enabled.
Reported-and-tested-by: Venkat Raghavulu <venkat.raghavulu@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPI / utils: Drop error messages from acpi_evaluate_reference()
Some of the error messages printed by acpi_evaluate_reference()
with the KERN_ERR priority should really be debug messages, but then
they would be redundant, because acpi_util_eval_error() is called
too at the same spots (except for one).
Drop the kernel messages from there entirely and leave the
acpi_util_eval_error() to handle the debug printing. In one case,
replace the kernel message with a call to acpi_util_eval_error().
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPI / scan: Change the level of _DEP-related messages to KERN_DEBUG
Two _DEP-related failure messages are printed as dev_err() which is
unnecessary and annoying. Use dev_dbg() to print them.
While at it, one of the messages should actually say it is related
to _DEP, so modify it to that effect.
Fixes: 40e7fcb19293 (ACPI: Add _DEP support to fix battery issue on Asus T100TA) Reported-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Linus Torvalds [Thu, 11 Dec 2014 05:17:00 +0000 (21:17 -0800)]
Merge tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"This time we have some more new material than we used to have during
the last couple of development cycles.
The most important part of it to me is the introduction of a unified
interface for accessing device properties provided by platform
firmware. It works with Device Trees and ACPI in a uniform way and
drivers using it need not worry about where the properties come from
as long as the platform firmware (either DT or ACPI) makes them
available. It covers both devices and "bare" device node objects
without struct device representation as that turns out to be necessary
in some cases. This has been in the works for quite a few months (and
development cycles) and has been approved by all of the relevant
maintainers.
On top of that, some drivers are switched over to the new interface
(at25, leds-gpio, gpio_keys_polled) and some additional changes are
made to the core GPIO subsystem to allow device drivers to manipulate
GPIOs in the "canonical" way on platforms that provide GPIO
information in their ACPI tables, but don't assign names to GPIO lines
(in which case the driver needs to do that on the basis of what it
knows about the device in question). That also has been approved by
the GPIO core maintainers and the rfkill driver is now going to use
it.
Second is support for hardware P-states in the intel_pstate driver.
It uses CPUID to detect whether or not the feature is supported by the
processor in which case it will be enabled by default. However, it
can be disabled entirely from the kernel command line if necessary.
Next is support for a platform firmware interface based on ACPI
operation regions used by the PMIC (Power Management Integrated
Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
That interface is used for manipulating power resources and for
thermal management: sensor temperature reporting, trip point setting
and so on.
Also the ACPI core is now going to support the _DEP configuration
information in a limited way. Basically, _DEP it supposed to reflect
off-the-hierarchy dependencies between devices which may be very
indirect, like when AML for one device accesses locations in an
operation region handled by another device's driver (usually, the
device depended on this way is a serial bus or GPIO controller). The
support added this time is sufficient to make the ACPI battery driver
work on Asus T100A, but it is general enough to be able to cover some
other use cases in the future.
Finally, we have a new cpufreq driver for the Loongson1B processor.
In addition to the above, there are fixes and cleanups all over the
place as usual and a traditional ACPICA update to a recent upstream
release.
As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver for
Intel platforms should be able to handle power management of the DMA
engine correctly, the cpufreq-dt driver should interact with the
thermal subsystem in a better way and the ACPI backlight driver should
handle some more corner cases, among other things.
On top of the ACPICA update there are fixes for race conditions in the
ACPICA's interrupt handling code which might lead to some random and
strange looking failures on some systems.
In the cleanups department the most visible part is the series of
commits targeted at getting rid of the CONFIG_PM_RUNTIME configuration
option. That was triggered by a discussion regarding the generic
power domains code during which we realized that trying to support
certain combinations of PM config options was painful and not really
worth it, because nobody would use them in production anyway. For
this reason, we decided to make CONFIG_PM_SLEEP select
CONFIG_PM_RUNTIME and that lead to the conclusion that the latter
became redundant and CONFIG_PM could be used instead of it. The
material here makes that replacement in a major part of the tree, but
there will be at least one more batch of that in the second part of
the merge window.
Specifics:
- Support for retrieving device properties information from ACPI _DSD
device configuration objects and a unified device properties
interface for device drivers (and subsystems) on top of that. As
stated above, this works with Device Trees and ACPI and allows
device drivers to be written in a platform firmware (DT or ACPI)
agnostic way. The at25, leds-gpio and gpio_keys_polled drivers are
now going to use this new interface and the GPIO subsystem is
additionally modified to allow device drivers to assign names to
GPIO resources returned by ACPI _CRS objects (in case _DSD is not
present or does not provide the expected data). The changes in
this set are mostly from Mika Westerberg, Rafael J Wysocki, Aaron
Lu, and Darren Hart with some fixes from others (Fabio Estevam,
Geert Uytterhoeven).
- Support for Hardware Managed Performance States (HWP) as described
in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
driver. CPUID is used to detect whether or not the feature is
supported by the processor. If supported, it will be enabled
automatically unless the intel_pstate=no_hwp switch is present in
the kernel command line. From Dirk Brandewie.
- New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).
- Support for firmware interface based on ACPI operation regions used
by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
platforms for power resource control and thermal management (Aaron
Lu).
- Limited support for retrieving off-the-hierarchy dependencies
between devices from ACPI _DEP device configuration objects and
deferred probing support for the ACPI battery driver based on the
_DEP information to make that driver work on Asus T100A (Lan
Tianyu).
- New cpufreq driver for the Loongson1B processor (Kelvin Cheung).
- ACPICA update to upstream revision 20141107 which only affects
tools (Bob Moore).
- Fixes for race conditions in the ACPICA's interrupt handling code
and in the ACPI code related to system suspend and resume (Lv Zheng
and Rafael J Wysocki).
- ACPI core fix for an RCU-related issue in the ioremap() regions
management code that slowed down significantly after CPUs had been
allowed to enter idle states even if they'd had RCU callbakcs
queued and triggered some problems in certain proprietary graphics
driver (and elsewhere). The fix replaces synchronize_rcu() in that
code with synchronize_rcu_expedited() which makes the issue go
away. From Konstantin Khlebnikov.
- ACPI LPSS (Low-Power Subsystem) driver fix to handle power
management of the DMA engine included into the LPSS correctly. The
problem is that the DMA engine doesn't have ACPI PM support of its
own and it simply is turned off when the last LPSS device having
ACPI PM support goes into D3cold. To work around that, the PM
domain used by the ACPI LPSS driver is redesigned so at least one
device with ACPI PM support will be on as long as the DMA engine is
in use. From Andy Shevchenko.
- ACPI backlight driver fix to avoid using it on "Win8-compatible"
systems where it doesn't work and where it was used by default by
mistake (Aaron Lu).
- Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and Ashwin
Chaugule (mostly related to the upcoming ARM64 support).
- Intel RAPL (Running Average Power Limit) power capping driver fixes
and improvements including new processor IDs (Jacob Pan).
- Generic power domains modification to power up domains after
attaching devices to them to meet the expectations of device
drivers and bus types assuming devices to be accessible at probe
time (Ulf Hansson).
- Preliminary support for controlling device clocks from the generic
power domains core code and modifications of the ARM/shmobile
platform to use that feature (Ulf Hansson).
- Assorted minor fixes and cleanups of the generic power domains core
code (Ulf Hansson, Geert Uytterhoeven).
- Assorted minor fixes and cleanups of the device clocks control code
in the PM core (Geert Uytterhoeven, Grygorii Strashko).
- Consolidation of device power management Kconfig options by making
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
which is now redundant (Rafael J Wysocki and Kevin Hilman). That
is the first batch of the changes needed for this purpose.
- Core device runtime power management support code cleanup related
to the execution of callbacks (Andrzej Hajda).
- cpuidle ARM support improvements (Lorenzo Pieralisi).
- cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and a
new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
Bartlomiej Zolnierkiewicz).
- New cpufreq driver callback (->ready) to be executed when the
cpufreq core is ready to use a given policy object and cpufreq-dt
driver modification to use that callback for cooling device
registration (Viresh Kumar).
- cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu, James
Geboski, Tomeu Vizoso).
- Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
Stefan Wahren, Petr Cvek).
- OPP (Operating Performance Points) framework modification to allow
OPPs to be removed too and update of a few cpufreq drivers
(cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
during initialization) on driver removal (Viresh Kumar).
- Hibernation core fixes and cleanups (Tina Ruchandani and Markus
Elfring).
- PM Kconfig fix related to CPU power management (Pankaj Dubey).
- cpupower tool fix (Prarit Bhargava)"
* tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (120 commits)
i2c-omap / PM: Drop CONFIG_PM_RUNTIME from i2c-omap.c
dmaengine / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tools: cpupower: fix return checks for sysfs_get_idlestate_count()
drivers: sh / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
e1000e / igb / PM: Eliminate CONFIG_PM_RUNTIME
MMC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
MFD / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
misc / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
media / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
input / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
leds: leds-gpio: Fix multiple instances registration without 'label' property
iio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hsi / OMAP / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
i2c-hid / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
drm / exynos / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
gpio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hwrandom / exynos / PM: Use CONFIG_PM in #ifdef
block / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
USB / PM: Drop CONFIG_PM_RUNTIME from the USB core
PM: Merge the SET*_RUNTIME_PM_OPS() macros
...
Linus Torvalds [Thu, 11 Dec 2014 04:58:52 +0000 (20:58 -0800)]
Merge tag 'pci-v3.19-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI changes from Bjorn Helgaas:
"Here are the PCI changes intended for v3.19. I don't think there's
anything very exciting here, but there was a lot of MSI-related stuff
coming via Thomas.
Details:
NUMA
- Allow numa_node override via sysfs (Prarit Bhargava)
Resource management
- Restore detection of read-only BARs (Myron Stowe)
- Shrink decoding-disabled window while sizing BARs (Myron Stowe)
- Add informational printk for invalid BARs (Myron Stowe)
- Remove fixed parameter in pci_iov_resource_bar() (Myron Stowe)
MSI
- Add pci_msi_ignore_mask to prevent writes to MSI/MSI-X Mask Bits (Yijing Wang)
- Revert "PCI: Add x86_msi.msi_mask_irq() and msix_mask_irq()" (Yijing Wang)
- s390/MSI: Use __msi_mask_irq() instead of default_msi_mask_irq() (Yijing Wang)
Virtualization
- xen: Process failure for pcifront_(re)scan_root() (Chen Gang)
- Make FLR and AF FLR reset warning messages different (Gavin Shan)
Generic host bridge driver
- Allocate config space windows after limiting bus number range (Lorenzo Pieralisi)
- Convert to DT resource parsing API (Lorenzo Pieralisi)
* tag 'pci-v3.19-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (28 commits)
PCI: Remove fixed parameter in pci_iov_resource_bar()
PCI: Add informational printk for invalid BARs
PCI: tegra: Add Kconfig help text
PCI: tegra: Do not build on 64-bit ARM
PCI: spear: Remove unnecessary OOM message
PCI: mvebu: Add a blank line after declarations
PCI: designware: Add a blank line after declarations
PCI: exynos: Remove unnecessary return statement
PCI: imx6: Use tabs for indentation
PCI: keystone: Remove unnecessary OOM message
PCI: Remove unused and broken to_hotplug_slot()
PCI: Make FLR and AF FLR reset warning messages different
PCI: dra7xx: Add __init annotation to dra7xx_add_pcie_port()
PCI: spear: Add __init annotation to spear13xx_add_pcie_port()
PCI: spear: Rename add_pcie_port(), pcie_init() to spear13xx_add_pcie_port(), etc.
PCI: dra7xx: Rename add_pcie_port() to dra7xx_add_pcie_port()
PCI: layerscape: Add Freescale Layerscape PCIe driver
PCI: Simplify if-return sequences
PCI: Delete unnecessary NULL pointer checks
PCI: Shrink decoding-disabled window while sizing BARs
...
Linus Torvalds [Thu, 11 Dec 2014 04:40:51 +0000 (20:40 -0800)]
Merge tag 'ktest-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-ktest
Pull ktest changes from Steven Rostedt:
"The following ktest updates were done:
- Fix handling the make kernelrelease change
- Fix make_min_config that was broken by new bisect_config changes
- Allow tests to undefine default options (not just being able to
override them)
- Print name of test (if defined) to start of test output"
* tag 'ktest-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-ktest:
ktest: Add back "tail -1" to kernelrelease make
ktest: Add name to running title
ktest: Allow tests to undefine default options
ktest: Fix make_min_config to handle new assign_configs call
ktest: Use make -s kernelrelease
Linus Torvalds [Thu, 11 Dec 2014 04:35:41 +0000 (20:35 -0800)]
Merge tag 'trace-seq-buf-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull nmi-safe seq_buf printk update from Steven Rostedt:
"This code is a fork from the trace-3.19 pull as it needed the
trace_seq clean ups from that branch.
This code solves the issue of performing stack dumps from NMI context.
The issue is that printk() is not safe from NMI context as if the NMI
were to trigger when a printk() was being performed, the NMI could
deadlock from the printk() internal locks. This has been seen in
practice.
With lots of review from Petr Mladek, this code went through several
iterations, and we feel that it is now at a point of quality to be
accepted into mainline.
Here's what is contained in this patch set:
- Creates a "seq_buf" generic buffer utility that allows a descriptor
to be passed around where functions can write their own "printk()"
formatted strings into it. The generic version was pulled out of
the trace_seq() code that was made specifically for tracing.
- The seq_buf code was change to model the seq_file code. I have a
patch (not included for 3.19) that converts the seq_file.c code
over to use seq_buf.c like the trace_seq.c code does. This was
done to make sure that seq_buf.c is compatible with seq_file.c. I
may try to get that patch in for 3.20.
- The seq_buf.c file was moved to lib/ to remove it from being
dependent on CONFIG_TRACING.
- The printk() was updated to allow for a per_cpu "override" of the
internal calls. That is, instead of writing to the console, a call
to printk() may do something else. This made it easier to allow
the NMI to change what printk() does in order to call dump_stack()
without needing to update that code as well.
- Finally, the dump_stack from all CPUs via NMI code was converted to
use the seq_buf code. The caller to trigger the NMI code would
wait till all the NMIs finished, and then it would print the
seq_buf data to the console safely from a non NMI context
One added bonus is that this code also makes the NMI dump stack work
on PREEMPT_RT kernels. As printk() includes sleeping locks on
PREEMPT_RT, printk() only writes to console if the console does not
use any rt_mutex converted spin locks. Which a lot do"
* tag 'trace-seq-buf-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
x86/nmi: Fix use of unallocated cpumask_var_t
printk/percpu: Define printk_func when printk is not defined
x86/nmi: Perform a safe NMI stack trace on all CPUs
printk: Add per_cpu printk func to allow printk to be diverted
seq_buf: Move the seq_buf code to lib/
seq-buf: Make seq_buf_bprintf() conditional on CONFIG_BINARY_PRINTF
tracing: Add seq_buf_get_buf() and seq_buf_commit() helper functions
tracing: Have seq_buf use full buffer
seq_buf: Add seq_buf_can_fit() helper function
tracing: Add paranoid size check in trace_printk_seq()
tracing: Use trace_seq_used() and seq_buf_used() instead of len
tracing: Clean up tracing_fill_pipe_page()
seq_buf: Create seq_buf_used() to find out how much was written
tracing: Add a seq_buf_clear() helper and clear len and readpos in init
tracing: Convert seq_buf fields to be like seq_file fields
tracing: Convert seq_buf_path() to be like seq_path()
tracing: Create seq_buf layer in trace_seq
Linus Torvalds [Thu, 11 Dec 2014 04:03:45 +0000 (20:03 -0800)]
Merge tag 'ftracetest-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull ftrace self-test updates from Steven Rostedt:
"Updates for the ftrace self tests:
- Added kprobes on ftrace testcase
- Sort test cases
- Add file to hold helper functions
- Use logfile name supported by busybox's mktemp
- Clear trace buffer after running kprobe test
- Fix show descriptions when run on dash shell
- Add --verbose option for showing echo output"
* tag 'ftracetest-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
ftracetest: Add --verbose option for showing echo output
ftracetest: Fix to show descriptions on dash
ftracetest: Add basic event tracing test cases
ftracetest: Clear trace buffer after running kprobe testcases
ftracetest: Use logfile name supported by busybox's mktemp
ftracetest: Add a couple of ftrace test cases
ftracetest: Add functions file that holds helper functions
ftracetest: Sort testcases
ftracetest: Add kprobes on ftrace testcase
Linus Torvalds [Thu, 11 Dec 2014 03:58:13 +0000 (19:58 -0800)]
Merge tag 'trace-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing updates from Steven Rostedt:
"There was a lot of clean ups and minor fixes. One of those clean ups
was to the trace_seq code. It also removed the return values to the
trace_seq_*() functions and use trace_seq_has_overflowed() to see if
the buffer filled up or not. This is similar to work being done to
the seq_file code as well in another tree.
Some of the other goodies include:
- Added some "!" (NOT) logic to the tracing filter.
- Fixed the frame pointer logic to the x86_64 mcount trampolines
- Added the logic for dynamic trampolines on !CONFIG_PREEMPT systems.
That is, the ftrace trampoline can be dynamically allocated and be
called directly by functions that only have a single hook to them"
* tag 'trace-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (55 commits)
tracing: Truncated output is better than nothing
tracing: Add additional marks to signal very large time deltas
Documentation: describe trace_buf_size parameter more accurately
tracing: Allow NOT to filter AND and OR clauses
tracing: Add NOT to filtering logic
ftrace/fgraph/x86: Have prepare_ftrace_return() take ip as first parameter
ftrace/x86: Get rid of ftrace_caller_setup
ftrace/x86: Have save_mcount_regs macro also save stack frames if needed
ftrace/x86: Add macro MCOUNT_REG_SIZE for amount of stack used to save mcount regs
ftrace/x86: Simplify save_mcount_regs on getting RIP
ftrace/x86: Have save_mcount_regs store RIP in %rdi for first parameter
ftrace/x86: Rename MCOUNT_SAVE_FRAME and add more detailed comments
ftrace/x86: Move MCOUNT_SAVE_FRAME out of header file
ftrace/x86: Have static tracing also use ftrace_caller_setup
ftrace/x86: Have static function tracing always test for function graph
kprobes: Add IPMODIFY flag to kprobe_ftrace_ops
ftrace, kprobes: Support IPMODIFY flag to find IP modify conflict
kprobes/ftrace: Recover original IP if pre_handler doesn't change it
tracing/trivial: Fix typos and make an int into a bool
tracing: Deletion of an unnecessary check before iput()
...
Linus Torvalds [Thu, 11 Dec 2014 02:34:42 +0000 (18:34 -0800)]
Merge branch 'akpm' (patchbomb from Andrew)
Merge first patchbomb from Andrew Morton:
- a few minor cifs fixes
- dma-debug upadtes
- ocfs2
- slab
- about half of MM
- procfs
- kernel/exit.c
- panic.c tweaks
- printk upates
- lib/ updates
- checkpatch updates
- fs/binfmt updates
- the drivers/rtc tree
- nilfs
- kmod fixes
- more kernel/exit.c
- various other misc tweaks and fixes
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (190 commits)
exit: pidns: fix/update the comments in zap_pid_ns_processes()
exit: pidns: alloc_pid() leaks pid_namespace if child_reaper is exiting
exit: exit_notify: re-use "dead" list to autoreap current
exit: reparent: call forget_original_parent() under tasklist_lock
exit: reparent: avoid find_new_reaper() if no children
exit: reparent: introduce find_alive_thread()
exit: reparent: introduce find_child_reaper()
exit: reparent: document the ->has_child_subreaper checks
exit: reparent: s/while_each_thread/for_each_thread/ in find_new_reaper()
exit: reparent: fix the cross-namespace PR_SET_CHILD_SUBREAPER reparenting
exit: reparent: fix the dead-parent PR_SET_CHILD_SUBREAPER reparenting
exit: proc: don't try to flush /proc/tgid/task/tgid
exit: release_task: fix the comment about group leader accounting
exit: wait: drop tasklist_lock before psig->c* accounting
exit: wait: don't use zombie->real_parent
exit: wait: cleanup the ptrace_reparented() checks
usermodehelper: kill the kmod_thread_locker logic
usermodehelper: don't use CLONE_VFORK for ____call_usermodehelper()
fs/hfs/catalog.c: fix comparison bug in hfs_cat_keycmp
nilfs2: fix the nilfs_iget() vs. nilfs_new_inode() races
...
Oleg Nesterov [Wed, 10 Dec 2014 23:55:28 +0000 (15:55 -0800)]
exit: pidns: fix/update the comments in zap_pid_ns_processes()
The comments in zap_pid_ns_processes() are not clear, we need to explain
how this code actually works.
1. "Ignore SIGCHLD" looks like optimization but it is not, we also
need this for correctness.
2. The comment above sys_wait4() could tell more.
EXIT_ZOMBIE child is only possible if it has exited before we
ignored SIGCHLD. Or if it is traced from the parent namespace,
but in this case it will be reaped by debugger after detach,
sys_wait4() acts as a synchronization point.
3. The comment about TASK_DEAD (EXIT_DEAD in fact) children is
outdated. Contrary to what it says we do not need to make sure
they all go away after 0a01f2cc390e "pidns: Make the pidns proc
mount/umount logic obvious".
At the same time, we do need to wait for nr_hashed==init_pids,
but the reasons are quite different and not obvious: setns().
Signed-off-by: Oleg Nesterov <oleg@redhat.com> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Aaron Tomlin <atomlin@redhat.com> Cc: Pavel Emelyanov <xemul@parallels.com> Cc: Serge Hallyn <serge.hallyn@ubuntu.com> Cc: Sterling Alexander <stalexan@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Oleg Nesterov [Wed, 10 Dec 2014 23:55:25 +0000 (15:55 -0800)]
exit: pidns: alloc_pid() leaks pid_namespace if child_reaper is exiting
alloc_pid() does get_pid_ns() beforehand but forgets to put_pid_ns() if it
fails because disable_pid_allocation() was called by the exiting
child_reaper.
We could simply move get_pid_ns() down to successful return, but this fix
tries to be as trivial as possible.
Signed-off-by: Oleg Nesterov <oleg@redhat.com> Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Aaron Tomlin <atomlin@redhat.com> Cc: Pavel Emelyanov <xemul@parallels.com> Cc: Serge Hallyn <serge.hallyn@ubuntu.com> Cc: Sterling Alexander <stalexan@redhat.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Oleg Nesterov [Wed, 10 Dec 2014 23:55:20 +0000 (15:55 -0800)]
exit: reparent: call forget_original_parent() under tasklist_lock
Shift "release dead children" loop from forget_original_parent() to its
caller, exit_notify(). It is safe to reap them even if our parent reaps
us right after we drop tasklist_lock, those children no longer have any
connection to the exiting task.
And this allows us to avoid write_lock_irq(tasklist_lock) right after it
was released by forget_original_parent(), we can simply call it with
tasklist_lock held.
While at it, move the comment about forget_original_parent() up to
this function.
Signed-off-by: Oleg Nesterov <oleg@redhat.com> Cc: Aaron Tomlin <atomlin@redhat.com> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Sterling Alexander <stalexan@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Oleg Nesterov [Wed, 10 Dec 2014 23:55:17 +0000 (15:55 -0800)]
exit: reparent: avoid find_new_reaper() if no children
Now that pid_ns logic was isolated we can change forget_original_parent()
to return right after find_child_reaper() when father->children is empty,
there is nothing to reparent in this case.
In particular this avoids find_alive_thread() and this can help if the
whole process exits and it has a lot of PF_EXITING threads at the start of
the thread list, this can easily lead to O(nr_threads ** 2) iterations.
Oleg Nesterov [Wed, 10 Dec 2014 23:55:14 +0000 (15:55 -0800)]
exit: reparent: introduce find_alive_thread()
Add the new simple helper to factor out the for_each_thread() code in
find_child_reaper() and find_new_reaper(). It can also simplify the
potential PF_EXITING -> exit_state change, plus perhaps we can change this
code to take SIGNAL_GROUP_EXIT into account.
Signed-off-by: Oleg Nesterov <oleg@redhat.com> Cc: Aaron Tomlin <atomlin@redhat.com> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Kay Sievers <kay@vrfy.org> Cc: Lennart Poettering <lennart@poettering.net> Cc: Sterling Alexander <stalexan@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Oleg Nesterov [Wed, 10 Dec 2014 23:55:11 +0000 (15:55 -0800)]
exit: reparent: introduce find_child_reaper()
find_new_reaper() does 2 completely different things. Not only it finds a
reaper, it also updates pid_ns->child_reaper or kills the whole namespace
if the caller is ->child_reaper.
Now that has_child_subreaper logic doesn't depend on child_reaper check we
can move that pid_ns code into a separate helper. IMHO this makes the
code more clean, and this allows the next changes.
Signed-off-by: Oleg Nesterov <oleg@redhat.com> Cc: Aaron Tomlin <atomlin@redhat.com> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Kay Sievers <kay@vrfy.org> Cc: Lennart Poettering <lennart@poettering.net> Cc: Sterling Alexander <stalexan@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Oleg Nesterov [Wed, 10 Dec 2014 23:55:08 +0000 (15:55 -0800)]
exit: reparent: document the ->has_child_subreaper checks
Swap the "init_task" and same_thread_group() checks. This way it is more
simple to document these checks and we can remove the link to the previous
discussion on lkml.
Signed-off-by: Oleg Nesterov <oleg@redhat.com> Cc: Aaron Tomlin <atomlin@redhat.com> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Kay Sievers <kay@vrfy.org> Cc: Lennart Poettering <lennart@poettering.net> Cc: Sterling Alexander <stalexan@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Oleg Nesterov [Wed, 10 Dec 2014 23:55:05 +0000 (15:55 -0800)]
exit: reparent: s/while_each_thread/for_each_thread/ in find_new_reaper()
Change find_new_reaper() to use for_each_thread() instead of deprecated
while_each_thread(). We do not bother to check "thread != father" in the
1st loop, we can rely on PF_EXITING check.
Note: this means the minor behavioural change: for_each_thread() starts
from the group leader. But this should be fine, nobody should make any
assumption about do_wait(__WNOTHREAD) when it comes to reparented tasks.
And this can avoid the pointless reparenting to a short-living thread
While zombie leaders are not that common.
Signed-off-by: Oleg Nesterov <oleg@redhat.com> Cc: Aaron Tomlin <atomlin@redhat.com> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Kay Sievers <kay@vrfy.org> Cc: Lennart Poettering <lennart@poettering.net> Cc: Sterling Alexander <stalexan@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Oleg Nesterov [Wed, 10 Dec 2014 23:55:02 +0000 (15:55 -0800)]
exit: reparent: fix the cross-namespace PR_SET_CHILD_SUBREAPER reparenting
find_new_reaper() assumes that "has_child_subreaper" logic is safe as
long as we are not the exiting ->child_reaper and this is doubly wrong:
1. In fact it is safe if "pid_ns->child_reaper == father"; there must
be no children after zap_pid_ns_processes() returns, so it doesn't
matter what we return in this case and even pid_ns->child_reaper is
wrong otherwise: we can't reparent to ->child_reaper == current.
This is not a bug, but this is confusing.
2. It is not safe if we are not pid_ns->child_reaper but from the same
thread group. We drop tasklist_lock before zap_pid_ns_processes(),
so another thread can lock it and choose the new reaper from the
upper namespace if has_child_subreaper == T, and this is obviously
wrong.
This is not that bad, zap_pid_ns_processes() won't return until the
the new reaper reaps all zombies, but this should be fixed anyway.
We could change for_each_thread() loop to use ->exit_state instead of
PF_EXITING which we had to use until 8aac62706ada, or we could change
copy_signal() to check CLONE_NEWPID before setting has_child_subreaper,
but lets change this code so that it is clear we can't look outside of
our namespace, otherwise same_thread_group(reaper, child_reaper) check
will look wrong and confusing anyway.
We can simply start from "father" and fix the problem. We can't wrongly
return a thread from the same thread group if ->is_child_subreaper == T,
we know that all threads have PF_EXITING set.
Signed-off-by: Oleg Nesterov <oleg@redhat.com> Cc: Aaron Tomlin <atomlin@redhat.com> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Kay Sievers <kay@vrfy.org> Cc: Lennart Poettering <lennart@poettering.net> Cc: Sterling Alexander <stalexan@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Oleg Nesterov [Wed, 10 Dec 2014 23:54:56 +0000 (15:54 -0800)]
exit: proc: don't try to flush /proc/tgid/task/tgid
proc_flush_task_mnt() always tries to flush task/pid, but this is
pointless if we reap the leader. d_invalidate() is recursive, and
if nothing else the next d_hash_and_lookup(tgid) should fail anyway.
Signed-off-by: Oleg Nesterov <oleg@redhat.com> Cc: Aaron Tomlin <atomlin@redhat.com> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Rik van Riel <riel@redhat.com> Cc: Sterling Alexander <stalexan@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Oleg Nesterov [Wed, 10 Dec 2014 23:54:48 +0000 (15:54 -0800)]
exit: wait: don't use zombie->real_parent
1. wait_task_zombie() uses p->real_parent to get psig/siglock. This is
correct but needs tasklist_lock, ->real_parent can exit.
We can use "current" instead. This is our natural child, its parent
must be our sub-thread.
2. Read psig/sig outside of ->siglock, ->signal is no longer protected
by this lock.
3. Fix the outdated comments about tasklist_lock. We can not race with
__exit_signal(), the whole thread group is dead, nobody but us can
call it.
Also clarify the usage of ->stats_lock and ->siglock.
Note: thread_group_cputime_adjusted() is sub-optimal in this case, we
probably want to export cputime_adjust() to avoid thread_group_cputime().
The comment says "all threads" but there are no other threads.
Signed-off-by: Oleg Nesterov <oleg@redhat.com> Cc: Aaron Tomlin <atomlin@redhat.com> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Rik van Riel <riel@redhat.com> Cc: Sterling Alexander <stalexan@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Oleg Nesterov [Wed, 10 Dec 2014 23:54:45 +0000 (15:54 -0800)]
exit: wait: cleanup the ptrace_reparented() checks
Now that EXIT_DEAD is the terminal state we can kill "int traced"
variable and check "state == EXIT_DEAD" instead to cleanup the code. In
particular, this way it is clear that the check obviously doesn't need
tasklist_lock.
Also fix the type of "unsigned long state", "long" was always wrong
although this doesn't matter because cmpxchg/xchg uses typeof(*ptr).
[akpm@linux-foundation.org: don't make me google the C Operator Precedence table] Signed-off-by: Oleg Nesterov <oleg@redhat.com> Cc: Aaron Tomlin <atomlin@redhat.com> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Rik van Riel <riel@redhat.com> Cc: Sterling Alexander <stalexan@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Oleg Nesterov [Wed, 10 Dec 2014 23:54:42 +0000 (15:54 -0800)]
usermodehelper: kill the kmod_thread_locker logic
Now that we do not call kernel_thread(CLONE_VFORK) from the worker
thread we can not deadlock if do_execve() in turn triggers another
call_usermodehelper(), we can remove the kmod_thread_locker code.
Note: we should probably kill khelper_wq and simply use one of the
global workqueues, say, system_unbound_wq, this special wq for umh buys
nothing nowadays.
Signed-off-by: Oleg Nesterov <oleg@redhat.com> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Oleg Nesterov <oleg@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Oleg Nesterov [Wed, 10 Dec 2014 23:54:39 +0000 (15:54 -0800)]
usermodehelper: don't use CLONE_VFORK for ____call_usermodehelper()
After "kernel/kmod: fix use-after-free of the sub_infostructure"
CLONE_VFORK in __call_usermodehelper() buys nothing, we rely on on
umh_complete() in ____call_usermodehelper() anyway.
Remove it. This also eliminates the unnecessary sleep/wakeup in the
likely case, and this allows the next change.
While at it, kill the "int wait" locals in ____call_usermodehelper() and
__call_usermodehelper(), they can safely use sub_info->wait.
Signed-off-by: Oleg Nesterov <oleg@redhat.com> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Oleg Nesterov <oleg@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rasmus Villemoes [Wed, 10 Dec 2014 23:54:37 +0000 (15:54 -0800)]
fs/hfs/catalog.c: fix comparison bug in hfs_cat_keycmp
Relying on the sign (after casting to int) of the difference of two
quantities for comparison is usually wrong. For example, should a-b
turn out to be 2^31, the return value of cmp(a,b) is -2^31; but that
would also be the return value from cmp(b, a). So a compares less than
b and b compares less than a. One can also easily find three values
a,b,c such that a compares less than b, b compares less than c, but a
does not compare less than c.
Ryusuke Konishi [Wed, 10 Dec 2014 23:54:34 +0000 (15:54 -0800)]
nilfs2: fix the nilfs_iget() vs. nilfs_new_inode() races
Same story as in commit 41080b5a2401 ("nfsd race fixes: ext2") (similar
ext2 fix) except that nilfs2 needs to use insert_inode_locked4() instead
of insert_inode_locked() and a bug of a check for dead inodes needs to
be fixed.
If nilfs_iget() is called from nfsd after nilfs_new_inode() calls
insert_inode_locked4(), nilfs_iget() will wait for unlock_new_inode() at
the end of nilfs_mkdir()/nilfs_create()/etc to unlock the inode.
If nilfs_iget() is called before nilfs_new_inode() calls
insert_inode_locked4(), it will create an in-core inode and read its
data from the on-disk inode. But, nilfs_iget() will find i_nlink equals
zero and fail at nilfs_read_inode_common(), which will lead it to call
iget_failed() and cleanly fail.
However, this sanity check doesn't work as expected for reused on-disk
inodes because they leave a non-zero value in i_mode field and it
hinders the test of i_nlink. This patch also fixes the issue by
removing the test on i_mode that nilfs2 doesn't need.
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andreas Rohner [Wed, 10 Dec 2014 23:54:29 +0000 (15:54 -0800)]
nilfs2: avoid duplicate segment construction for fsync()
This patch removes filemap_write_and_wait_range() from nilfs_sync_file(),
because it triggers a data segment construction by calling
nilfs_writepages() with WB_SYNC_ALL. A data segment construction does not
remove the inode from the i_dirty list and it does not clear the
NILFS_I_DIRTY flag. Therefore nilfs_inode_dirty() still returns true,
which leads to an unnecessary duplicate segment construction in
nilfs_sync_file().
A call to filemap_write_and_wait_range() is not needed, because NILFS2
does not rely on the generic writeback mechanisms. Instead it implements
its own mechanism to collect all dirty pages and write them into segments.
It is more efficient to initiate the segment construction directly in
nilfs_sync_file() without the detour over filemap_write_and_wait_range().
Additionally the lock of i_mutex is not needed, because all code blocks
that are protected by i_mutex are also protected by a NILFS transaction:
For nilfs_lookup() i_mutex is held for the parent directory, to protect it
from modification. The segment construction does not modify directory
inodes, so no lock is needed.
nilfs_fiemap() reads the block layout on the disk, by using
nilfs_bmap_lookup_contig(). This is already protected by bmap->b_sem.
Signed-off-by: Andreas Rohner <andreas.rohner@gmx.net> Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Xunlei Pang [Wed, 10 Dec 2014 23:54:26 +0000 (15:54 -0800)]
rtc: refine rtc_timer_do_work() to consider other set alarm failures
rtc_timer_do_work() only judges -ETIME failure of__rtc_set_alarm(), but
doesn't handle other failures like -EIO, -EBUSY, etc.
If there is a failure other than -ETIME, the next rtc_timer will stay in
the timerqueue. Then later rtc_timers will be enqueued directly because
they have a later expires time, so the alarm irq will never be programmed.
When such failures happen, this patch will retry __rtc_set_alarm(), if
still can't program the alarm time, it will remove current rtc_timer from
timerqueue and fetch next one, thus preventing it from affecting other rtc
timers.
Signed-off-by: Xunlei Pang <pang.xunlei@linaro.org> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: John Stultz <john.stultz@linaro.org> Cc: Arnd Bergmann <arnd.bergmann@linaro.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Xunlei Pang [Wed, 10 Dec 2014 23:54:23 +0000 (15:54 -0800)]
rtc/ab8500: set uie_unsupported flag
Currently, ab8500 doesn't set uie_unsupported of rtc_device, while it
doesn't support UIE, see ab8500_rtc_set_alarm().
Thus, when going through rtc_update_irq_enable()->rtc_timer_enqueue(),
there's a chance it has an alarm timer1 queued before which is going to
fired, so this update timer2 will be queued because it isn't the leftmost
one, which means rtc_timer_enqueue() will return 0.
This will result in two problems:
1) UIE EMUL will not be used.
2) When the alarm timer1 is fired, in rtc_timer_do_work() timer2 will
fail to set the alarm time, so this rtc will disfunctional due to
timer2 with the earliest expires in the timerqueue.
So, rtc drivers must set this flag if they don't support UIE.
Signed-off-by: Xunlei Pang <pang.xunlei@linaro.org> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: John Stultz <john.stultz@linaro.org> Cc: Arnd Bergmann <arnd.bergmann@linaro.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sanchayan Maity [Wed, 10 Dec 2014 23:54:20 +0000 (15:54 -0800)]
drivers/rtc/rtc-snvs: fix suspend/resume
The alarm interrupt handler also reads registers which are part of SNVS
and need clocks enabled. However, the resume function is called after
IRQ's have been enabled, hence this leads to a abort:
Unhandled fault: external abort on non-linefetch (0x1008) at 0x908c604c
Internal error: : 1008 [#1] ARM
Modules linked in:
CPU: 0 PID: 421 Comm: sh Not tainted 3.18.0-rc5-00135-g0689c67-dirty #1592
task: 8e03e800 ti: 8cad8000 task.ti: 8cad8000
PC is at snvs_rtc_irq_handler+0x14/0x74
LR is at handle_irq_event_percpu+0x3c/0x144
Fix this by using the .{suspend/resume}_noirq callbacks instead of
.{suspend/resume} .
Sanchayan Maity [Wed, 10 Dec 2014 23:54:17 +0000 (15:54 -0800)]
drivers/rtc/rtc-snvs: add clock support
Add clock enable and disable support for the SNVS peripheral, which is
required for using the RTC within the SNVS block.
The clock is not strictly enforced, as this would break the i.MX devices.
The clocking for the i.MX devices seems to be enabled elsewhere and
enabling RTC SNVS for Vybrid results in a crash. This patch adds the
clock support but also makes it optional so Vybrid platform can use the
clock if defined while making sure not to break i.MX.
Arnaud Ebalard [Wed, 10 Dec 2014 23:54:11 +0000 (15:54 -0800)]
drivers/rtc/rtc-isl12057.c: report error code upon failure in dev_err() calls
As pointed out by Mark, it is generally useful to log the error code when
reporting a failure. This patch improves existing calls to dev_err() in
ISL12057 driver to also report error code.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org> Suggested-by: Mark Brown <broonie@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: Peter Huewe <peter.huewe@infineon.com> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Thierry Reding <treding@nvidia.com> Cc: Grant Likely <grant.likely@linaro.org> Acked-by: Uwe Kleine-König <uwe@kleine-koenig.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Arnaud Ebalard [Wed, 10 Dec 2014 23:54:08 +0000 (15:54 -0800)]
drivers/rtc/rtc-isl12057.c: add proper handling of oscillator failure bit
As suggested by Uwe, instead of clearing oscillator failure bit
unconditionally at driver load, this patch adds proper handling of the
flag. The driver now returns -ENODATA when reading time from the device
and oscillator failure bit is set. The flag is now cleared only when the
a new time value is pushed to the device.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org> Reported-by: Uwe Kleine-König <uwe@kleine-koenig.org> Acked-by: Uwe Kleine-König <uwe@kleine-koenig.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: Peter Huewe <peter.huewe@infineon.com> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Thierry Reding <treding@nvidia.com> Cc: Mark Brown <broonie@kernel.org> Cc: Grant Likely <grant.likely@linaro.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Arnaud Ebalard [Wed, 10 Dec 2014 23:54:05 +0000 (15:54 -0800)]
drivers/rtc/rtc-isl12057.c: add support for century bit
The month register of ISL12057 RTC chip includes a century bit which
reports overflow of year register from 99 to 0. This bit can also be
written, which allows using it to extend the time interval the chip can
support from 99 to 199 years.
This patch adds support for century overflow bit in tm to regs and regs to
tm helpers in ISL12057 driver.
This was tested by putting a device 100 years in the future (using a
specific kernel due to the inability of userland tools such as date or
hwclock to pass year 2038), rebooting on a kernel w/ this patch applied
and verifying the device was still 100 years in the future.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org> Suggested-by: Uwe Kleine-König <uwe@kleine-koenig.org> Acked-by: Uwe Kleine-König <uwe@kleine-koenig.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: Peter Huewe <peter.huewe@infineon.com> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Thierry Reding <treding@nvidia.com> Cc: Mark Brown <broonie@kernel.org> Cc: Grant Likely <grant.likely@linaro.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Arnaud Ebalard [Wed, 10 Dec 2014 23:54:02 +0000 (15:54 -0800)]
drivers/rtc/rtc-isl12057.c: fix masking of register values
When Intersil ISL12057 support was added by commit 70e123373c05 ("rtc: Add
support for Intersil ISL12057 I2C RTC chip"), two masks for time registers
values imported from the device were either wrong or omitted, leading to
additional bits from those registers to impact read values:
- mask for hour register value when reading it in AM/PM mode. As
AM/PM mode is not the usual mode used by the driver, this error
would only have an impact on an externally configured RTC hour
later read by the driver.
- mask for month value. The lack of masking would provide an
erroneous value if century bit is set.
This patch fixes those two masks.
Fixes: 70e123373c05 ("rtc: Add support for Intersil ISL12057 I2C RTC chip") Signed-off-by: Arnaud Ebalard <arno@natisbad.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: Peter Huewe <peter.huewe@infineon.com> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Thierry Reding <treding@nvidia.com> Cc: Mark Brown <broonie@kernel.org> Cc: Grant Likely <grant.likely@linaro.org> Acked-by: Uwe Kleine-König <uwe@kleine-koenig.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Søren Andersen [Wed, 10 Dec 2014 23:53:54 +0000 (15:53 -0800)]
drivers/rtc/rtc-ds1374.c: add watchdog support
Add support for the watchdog functionality of the DS1374 rtc. Based on
the m41t80 watchdog functionality Note: watchdog uses the same registers
as alarm.
Barry Song [Wed, 10 Dec 2014 23:53:51 +0000 (15:53 -0800)]
drivers/rtc/rtc-sirfsoc.c: replace local_irq_disable by spin_lock_irq for SMP safety
Signed-off-by: Barry Song <Baohua.Song@csr.com> Cc: hao liu <hao.liu@csr.com> Cc: Alessandro Zummo <a.zummo@towertech.it> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jan Kardell [Wed, 10 Dec 2014 23:53:46 +0000 (15:53 -0800)]
rtc: pcf8563: clear expired alarm at boot time
In case the card is woken up of the rtc alarm, the
devm_rtc_device_register function detects it as a pending alarm about a
month in the future. Fix this by clearing the alarm in module probe.
Signed-off-by: Jan Kardell <jan.kardell@telliq.com> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: Grant Likely <grant.likely@linaro.org> Cc: Rob Herring <robh+dt@kernel.org> Cc: Vincent Donnefort <vdonnefort@gmail.com> Cc: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jan Kardell [Wed, 10 Dec 2014 23:53:40 +0000 (15:53 -0800)]
rtc: pcf8563: handle consequeces of lacking second alarm reg
To guarantee that a set alarm occurs in the future, the set alarm time
is rounded up to the nearest minute. Also we cannot handle UIE as it
requires second precision.
Signed-off-by: Jan Kardell <jan.kardell@telliq.com> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: Grant Likely <grant.likely@linaro.org> Cc: Rob Herring <robh+dt@kernel.org> Cc: Vincent Donnefort <vdonnefort@gmail.com> Cc: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Johan Hovold [Wed, 10 Dec 2014 23:53:29 +0000 (15:53 -0800)]
ARM: dts: am335x-boneblack: enable power off and rtc wake up
Configure the RTC as system-power controller, which allows the system to
be powered off as well as woken up again on subsequent RTC alarms.
Note that the PMIC needs to be put in SLEEP (rather than OFF) mode to
maintain RTC power. Specifically, this means that the PMIC
ti,pmic-shutdown-controller property must be left unset in order to be
able to wake up on RTC alarms.
Tested on BeagleBone Black (rev A5).
Signed-off-by: Johan Hovold <johan@kernel.org> Reviewed-by: Felipe Balbi <balbi@ti.com> Tested-by: Felipe Balbi <balbi@ti.com> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: Tony Lindgren <tony@atomide.com> Cc: Benot Cousson <bcousson@baylibre.com> Cc: Lokesh Vutla <lokeshvutla@ti.com> Cc: Guenter Roeck <linux@roeck-us.net> Cc: Sekhar Nori <nsekhar@ti.com> Cc: Tero Kristo <t-kristo@ti.com> Cc: Keerthy J <j-keerthy@ti.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Johan Hovold [Wed, 10 Dec 2014 23:53:13 +0000 (15:53 -0800)]
rtc: omap: add support for pmic_power_en
Add new property "ti,system-power-controller" to register the RTC as a
power-off handler.
Some RTC IP revisions can control an external PMIC via the pmic_power_en
pin, which can be configured to transition to OFF on ALARM2 events and
back to ON on subsequent ALARM (wakealarm) events.
This is based on earlier work by Colin Foe-Parker and AnilKumar Ch. [1]
Johan Hovold [Wed, 10 Dec 2014 23:53:04 +0000 (15:53 -0800)]
rtc: omap: silence bogus power-up reset message at probe
Some legacy RTC IP revisions has a power-up reset flag in the status
register that later revisions lack.
As this flag is always read back as set on later revisions (or is
overloaded with a different flag), make sure to only clear the flag and
print the info message on legacy platforms.
Signed-off-by: Johan Hovold <johan@kernel.org> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: Tony Lindgren <tony@atomide.com> Cc: Benot Cousson <bcousson@baylibre.com> Cc: Lokesh Vutla <lokeshvutla@ti.com> Cc: Guenter Roeck <linux@roeck-us.net> Cc: Sekhar Nori <nsekhar@ti.com> Cc: Tero Kristo <t-kristo@ti.com> Cc: Keerthy J <j-keerthy@ti.com> Tested-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Johan Hovold [Wed, 10 Dec 2014 23:52:58 +0000 (15:52 -0800)]
rtc: omap: remove DRIVER_NAME macro
Remove DRIVER_NAME macro which was used for unrelated strings (e.g.
id-table entry and module name), but not for related ones (e.g. module
name and alias).
Also move the module alias to the other module-info entries.
Signed-off-by: Johan Hovold <johan@kernel.org> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: Tony Lindgren <tony@atomide.com> Cc: Benot Cousson <bcousson@baylibre.com> Cc: Lokesh Vutla <lokeshvutla@ti.com> Cc: Guenter Roeck <linux@roeck-us.net> Cc: Sekhar Nori <nsekhar@ti.com> Cc: Tero Kristo <t-kristo@ti.com> Tested-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Johan Hovold [Wed, 10 Dec 2014 23:52:43 +0000 (15:52 -0800)]
rtc: omap: fix class-device registration
Make sure not to register the class device until after the device has
been configured.
Currently, the device is not fully configured (e.g. 24-hour mode) when
the class device is registered, something which involves driver
callbacks for example to read the current time.
Signed-off-by: Johan Hovold <johan@kernel.org> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: Tony Lindgren <tony@atomide.com> Cc: Benot Cousson <bcousson@baylibre.com> Cc: Lokesh Vutla <lokeshvutla@ti.com> Cc: Guenter Roeck <linux@roeck-us.net> Cc: Sekhar Nori <nsekhar@ti.com> Cc: Tero Kristo <t-kristo@ti.com> Cc: Keerthy J <j-keerthy@ti.com> Tested-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Johan Hovold [Wed, 10 Dec 2014 23:52:30 +0000 (15:52 -0800)]
rtc: omap: fix clock-source configuration
This series fixes a few issues with the omap rtc-driver, cleans up a
bit, adds device abstraction, and finally adds support for the PMIC
control feature found in some revisions of this RTC IP block.
Ultimately, this allows for powering off the Beaglebone and waking it up
again on RTC alarms.
This patch (of 20):
Make sure not to reset the clock-source configuration when enabling the
32kHz clock mux.
Until the clock source can be configured through device tree we must not
overwrite settings made by the bootloader (e.g. clock-source
selection).
Fixes: cd914bba03d8 ("drivers/rtc/rtc-omap.c: add support for enabling 32khz clock") Signed-off-by: Johan Hovold <johan@kernel.org> Reviewed-by: Felipe Balbi <balbi@ti.com> Tested-by: Felipe Balbi <balbi@ti.com> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: Tony Lindgren <tony@atomide.com> Cc: Benot Cousson <bcousson@baylibre.com> Cc: Lokesh Vutla <lokeshvutla@ti.com> Cc: Guenter Roeck <linux@roeck-us.net> Cc: Sekhar Nori <nsekhar@ti.com> Cc: Tero Kristo <t-kristo@ti.com> Cc: Keerthy J <j-keerthy@ti.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hyogi Gim [Wed, 10 Dec 2014 23:52:27 +0000 (15:52 -0800)]
drivers/rtc/interface.c: check the validation of rtc_time in __rtc_read_time
Some rtc devices always return '0' when rtc_class_ops.read_time is
called. So if rtc_time isn't verified in callback, rtc interface cannot
know whether rtc_time is valid.
Check rtc_time by using 'rtc_valid_tm' in '__rtc_read_time'. And add
the message for debugging.
Signed-off-by: Hyogi Gim <hyogi.gim@lge.com> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: John Stultz <john.stultz@linaro.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Guo Zeng [Wed, 10 Dec 2014 23:52:24 +0000 (15:52 -0800)]
drivers/rtc/rtc-sirfsoc.c: move hardware initilization earlier in probe
Move rtc register to be later than hardware initialization. The reason
is that devm_rtc_device_register() will do read_time() which is a
callback accessing hardware. This sometimes causes a hang in the
hardware related callback.
Signed-off-by: Guo Zeng <guo.zeng@csr.com> Signed-off-by: Barry Song <Baohua.Song@csr.com> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jan Kara [Wed, 10 Dec 2014 23:52:22 +0000 (15:52 -0800)]
ncpfs: return proper error from NCP_IOC_SETROOT ioctl
If some error happens in NCP_IOC_SETROOT ioctl, the appropriate error
return value is then (in most cases) just overwritten before we return.
This can result in reporting success to userspace although error happened.
This bug was introduced by commit 2e54eb96e2c8 ("BKL: Remove BKL from
ncpfs"). Propagate the errors correctly.
Fixes: 2e54eb96e2c80 ("BKL: Remove BKL from ncpfs") Signed-off-by: Jan Kara <jack@suse.cz> Cc: Petr Vandrovec <petr@vandrovec.name> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andy Lutomirski [Wed, 10 Dec 2014 23:52:19 +0000 (15:52 -0800)]
init: allow CONFIG_INIT_FALLBACK=n to disable defaults if init= fails
If a user puts init=/whatever on the command line and /whatever can't be
run, then the kernel will try a few default options before giving up. If
init=/whatever came from a bootloader prompt, then this is unexpected but
probably harmless. On the other hand, if it comes from a script (e.g. a
tool like virtme or perhaps a future kselftest script), then the fallbacks
are likely to exist, but they'll do the wrong thing. For example, they
might unexpectedly invoke systemd.
This adds a config option CONFIG_INIT_FALLBACK. If unset, then a failure
to run the specified init= process be fatal.
The tentative plan is to remove CONFIG_INIT_FALLBACK for 3.20.
[akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Andy Lutomirski <luto@amacapital.net> Cc: Rob Landley <rob@landley.net> Cc: Chuck Ebbert <cebbert.lkml@gmail.com> Cc: Randy Dunlap <rdunlap@infradead.org> Cc: Shuah Khan <shuah.kh@samsung.com> Cc: Frank Rowand <frowand.list@gmail.com> Cc: Josh Triplett <josh@joshtriplett.org> Acked-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jungseung Lee [Wed, 10 Dec 2014 23:52:16 +0000 (15:52 -0800)]
fs/binfmt_elf.c: fix internal inconsistency relating to vma dump size
vma_dump_size() has been used several times on actual dumper and it is
supposed to return the same value for the same vma. But vma_dump_size()
could return different values for same vma.
The known problem case is concurrent shared memory removal. If a vma is
used for a shared memory and that shared memory is removed between
writing program header and dumping vma memory, this will result in a
dump file which is internally consistent.
To fix the problem, we set baseline to get dump size and store the size
into vma_filesz and always use the same vma dump size which is stored in
vma_filsz. The consistnecy with reality is not actually guranteed, but
it's tolerable since that is fully consistent with base line.
Signed-off-by: Jungseung Lee <js07.lee@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mike Frysinger [Wed, 10 Dec 2014 23:52:10 +0000 (15:52 -0800)]
binfmt_misc: clean up code style a bit
Clean up various coding style issues that checkpatch complains about.
No functional changes here.
Signed-off-by: Mike Frysinger <vapier@gentoo.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Joe Perches <joe@perches.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mike Frysinger [Wed, 10 Dec 2014 23:52:08 +0000 (15:52 -0800)]
binfmt_misc: add comments & debug logs
When trying to develop a custom format handler, the errors returned all
effectively get bucketed as EINVAL with no kernel messages. The other
errors (ENOMEM/EFAULT) are internal/obvious and basic. Thus any time a
bad handler is rejected, the developer has to walk the dense code and
try to guess where it went wrong. Needing to dive into kernel code is
itself a fairly high barrier for a lot of people.
To improve this situation, let's deploy extensive pr_debug markers at
logical parse points, and add comments to the dense parsing logic. It
let's you see exactly where the parsing aborts, the string the kernel
received (useful when dealing with shell code), how it translated the
buffers to binary data, and how it will apply the mask at runtime.
The [raw] lines show us exactly what was received from userspace. The
lines after that show us how the kernel has decoded things.
Signed-off-by: Mike Frysinger <vapier@gentoo.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Joe Perches <joe@perches.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joe Perches [Wed, 10 Dec 2014 23:52:05 +0000 (15:52 -0800)]
checkpatch: add ability to --fix (coalesce) string fragments on multiple lines
Add --fix option to coalesce string fragments.
This does not coalesce string fragments that have newline terminations or
are otherwise exempted.
Other miscellanea:
o move all the string tests together.
o fix get_quoted_string function for tab characters
o fix concatination typo
Signed-off-by: Joe Perches <joe@perches.com> Cc: Andy Whitcroft <apw@canonical.com> Cc: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joe Perches [Wed, 10 Dec 2014 23:52:02 +0000 (15:52 -0800)]
checkpatch: add --strict "pointer comparison to NULL" test
It seems there are more and more uses of "if (!ptr)" in preference to "if
(ptr == NULL)" so add a --strict test to emit a message when using the
latter form.
This also finds (ptr != NULL).
Fix it too if desired.
Signed-off-by: Joe Perches <joe@perches.com> Cc: Dan Carpenter <dan.carpenter@oracle.com> Cc: Greg KH <gregkh@linuxfoundation.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joe Perches [Wed, 10 Dec 2014 23:51:57 +0000 (15:51 -0800)]
checkpatch: add --strict preference for #defines using BIT(foo)
Using BIT(foo) and BIT_ULL(bar) is more common now. Suggest using these
macros over #defines with 1<<value.
Add a --fix option too.
Signed-off-by: Joe Perches <joe@perches.com> Cc: David Miller <davem@davemloft.net> Cc: Jiri Pirko <jiri@resnulli.us> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Julius Werner [Wed, 10 Dec 2014 23:51:54 +0000 (15:51 -0800)]
checkpatch: allow certain SI units with three characters
Checkpatch flags CamelCase identifiers in strict mode, but it has a
feature to ignore parts with only two characters to allow for SI units
like mV or uA. Unfortunately, not all SI units fit in two characters, and
not all are lower case followed by upper case.
This patch adds hardcoded detection for frequency and 1024-based size
units (Hz/KHz/MHz/GHz/THz and KiB/MiB/GiB/TiB), since allowing any three
character combinations might be too lenient. The list can later be
expanded as needed.
Signed-off-by: Julius Werner <jwerner@chromium.org> Acked-by: Joe Perches <joe@perches.com> Cc: Andy Whitcroft <apw@canonical.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joe Perches [Wed, 10 Dec 2014 23:51:49 +0000 (15:51 -0800)]
checkpatch: reduce MAINTAINERS update message frequency
When files are being added/moved/deleted and a patch contains an update to
the MAINTAINERS file, assume it's to update the MAINTAINERS file correctly
and do not emit the "does MAINTAINERS need updating?" message.
Reported by many people.
Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joe Perches [Wed, 10 Dec 2014 23:51:37 +0000 (15:51 -0800)]
checkpatch: improve test for no space after cast
sizeof(foo) is not a cast, allow a space after it.
Signed-off-by: Joe Perches <joe@perches.com> Tested-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rasmus Villemoes [Wed, 10 Dec 2014 23:51:27 +0000 (15:51 -0800)]
lib/lcm.c: ensure correct result whenever it fits
Ensure that lcm(a,b) returns the mathematically correct result, provided
it fits in an unsigned long. The current version returns garbage if a*b
overflows, even if the final result would fit.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> Cc: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alex Elder [Wed, 10 Dec 2014 23:51:21 +0000 (15:51 -0800)]
printk: drop logbuf_cpu volatile qualifier
Pranith Kumar posted a patch in which removed the "volatile"
qualifier for the "logbuf_cpu" variable in vprintk_emit().
https://lkml.org/lkml/2014/11/13/894
In his patch, he used ACCESS_ONCE() for all references to
that symbol to provide whatever protection was intended.
There was some discussion that followed, and in the end Steven Rostedt
concluded that not only was "volatile" not needed, neither was it
required to use ACCESS_ONCE(). I offered an elaborate description that
concluded Steven was right, and Pranith asked me to submit an
alternative patch. And this is it.
The basic reason "volatile" is not needed is that "logbuf_cpu" has
static storage duration, and vprintk_emit() is an exported
interface. This means that the value of logbuf_cpu must be read
from memory the first time it is used in a particular call of
vprintk_emit(). The variable's value is read only once in that
function, when it's read it'll be the copy from memory (or cache).
In addition, the value of "logbuf_cpu" is only ever written under
protection of a spinlock. So the value that is read is the "real"
value (and not an out-of-date cached one). If its value is not
UINT_MAX, it is the current CPU's processor id, and it will have
been last written by the running CPU.
Signed-off-by: Alex Elder <elder@linaro.org> Reported-by: Pranith Kumar <bobby.prani@gmail.com> Suggested-by: Steven Rostedt <rostedt@goodmis.org> Reviewed-by: Jan Kara <jack@suse.cz> Cc: Petr Mladek <pmladek@suse.cz> Cc: Luis R. Rodriguez <mcgrof@suse.com> Cc: Joe Perches <joe@perches.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
projects / mirror_ubuntu-kernels.git / log