Remove a duplicate vendor+subvendor pin fixup entry as one is masking
the other and making it unreachable. Consider the more specific newcomer
as a second chance instead.
The generic entry is made less strict to also match for laptops with
slightly different 0x12 pin configuration. Tested on Lenovo Yoga 6 (AMD)
where 0x12 is 0x40000000.
Fixes: 607184cb1635 ("ALSA: hda/realtek - Add supported for more Lenovo ALC285 Headset Button") Signed-off-by: Sami Loone <sami@loone.fi> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/YIXS+GT/dGI/LtK6@yoga Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Fix two bugs with the Intel HDA Realtek ALC233 sound codec
present in Intel NUC NUC8i7BEH and probably a few other similar
NUC models.
These codecs advertise a 4-level microphone input boost amplifier on
pin 0x19, but the highest two boost settings do not work correctly,
and produce only low analog noise that does not seem to contain any
discernible signal. There is an existing fixup for this exact problem
but for a different PCI subsystem ID, so we re-use that logic.
Changing the boost level also triggers a DC spike in the input signal
that bleeds off over about a second and overwhelms any input during
that time. Thankfully, the existing fixup has the side effect of
making the boost control show up in userspace as a mute/unmute switch,
and this keeps (e.g.) PulseAudio from fiddling with it during normal
input volume adjustments.
Finally, the NUC hardware has built-in inverted stereo mics. This
patch also enables the usual fixup for this so the two channels cancel
noise instead of the actual signal.
[ Re-ordered the quirk entry point by tiwai ]
Signed-off-by: Phil Calvin <phil@philcalvin.com> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/80dc5663-7734-e7e5-25ef-15b5df24511a@philcalvin.com Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The GA503 has almost exactly the same default setup as the GA401
model with the same issues. The GA401 quirks solve all the issues
so we will use the full quirk chain.
Signed-off-by: Luke D Jones <luke@ljones.dev> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20210419030411.28304-1-luke@ljones.dev Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The decibel volume range contains a negative maximum value resulting in
pipewire complaining about the device and effectivly having no sound
output. The wrong values also resulted in the headset sounding muted
already at a mixer level of about ~25%.
In the current code, we have some assumption that the audio clock
selector has been set up implicitly and don't want to touch it unless
it's really needed for the fallback autoclock setup. This works for
most devices but some seem having a problem. Partially this was
covered for the devices with a single connector at the initialization
phase (commit 086b957cc17f "ALSA: usb-audio: Skip the clock selector
inquiry for single connections"), but also there are cases where the
wrong clock set up is kept silently. The latter seems to be the cause
of the noises on Behringer devices.
In this patch, we explicitly set up the audio clock selector whenever
the appropriate node is found.
In snd_sb_qsound_build, snd_ctl_add(..,p->qsound_switch...) and
snd_ctl_add(..,p->qsound_space..) are called. But the second
arguments of snd_ctl_add() could be freed via snd_ctl_add_replace()
->snd_ctl_free_one(). After the error code is returned,
snd_sb_qsound_destroy(p) is called in __error branch.
But in snd_sb_qsound_destroy(), the freed p->qsound_switch and
p->qsound_space are still used by snd_ctl_remove().
My patch set p->qsound_switch and p->qsound_space to NULL if
snd_ctl_add() failed to avoid the uaf bugs. But these codes need
to further be improved with the code style.
Just re-order the cx5066_fixups[] entries for HP devices for avoiding
the oversight of the duplicated or unapplied item in future.
No functional changes.
Also Cc-to-stable for the further patch applications.
Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20210428112704.23967-14-tiwai@suse.de Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
In snd_emu8000_create_mixer, the callee snd_ctl_add(..,emu->controls[i])
calls snd_ctl_add_replace(.., kcontrol,..). Inside snd_ctl_add_replace(),
if error happens, kcontrol will be freed by snd_ctl_free_one(kcontrol).
Then emu->controls[i] points to a freed memory, and the execution comes
to __error branch of snd_emu8000_create_mixer. The freed emu->controls[i]
is used in snd_ctl_remove(card, emu->controls[i]).
My patch set emu->controls[i] to NULL if snd_ctl_add() failed to avoid
the uaf.
A review of the code showed, that this function which is exposed
within the whole kernel should do a parameter check for the
amount of bytes requested. If this requested bytes is too high
an unsigned int overflow could happen causing this function to
try to memcpy a really big memory chunk.
This is not a security issue as there are only two invocations
of this function from arch/s390/include/asm/archrandom.h and both
are not exposed to userland.
Reported-by: Sven Schnelle <svens@linux.ibm.com> Signed-off-by: Harald Freudenberger <freude@linux.ibm.com> Signed-off-by: Heiko Carstens <hca@linux.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Since the 'mfs' member has been declared as 'u32' in include/scsi/libfc.h,
use the %u format specifier instead of %hu. This patch fixes the following
clang compiler warning:
warning: format specifies type
'unsigned short' but the argument has type 'u32' (aka 'unsigned int')
[-Wformat]
"lport->mfs:%hu\n", mfs, lport->mfs);
~~~ ^~~~~~~~~~
%u
Link: https://lore.kernel.org/r/20210415220826.29438-8-bvanassche@acm.org Cc: Hannes Reinecke <hare@suse.de> Signed-off-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
pm_runtime_get_sync() will increase the rumtime PM counter
even it returns an error. Thus a pairing decrement is needed
to prevent refcount leak. Fix this by replacing this API with
pm_runtime_resume_and_get(), which will not change the runtime
PM counter on error.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn> Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
SLI-4 does not contain a PORT_CAPABILITIES mailbox command (only SLI-3
does, and SLI-3 doesn't use it), yet there are SLI-4 code paths that have
code to issue the command. The command will always fail.
Remove the code for the mailbox command and leave only the resulting
"failure path" logic.
Link: https://lore.kernel.org/r/20210412013127.2387-12-jsmart2021@gmail.com Co-developed-by: Justin Tee <justin.tee@broadcom.com> Signed-off-by: Justin Tee <justin.tee@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
In SLI-4, when performing a mailbox command with MBX_POLL, the driver uses
the BMBX register to send the command rather than the MQ. A flag is set
indicating the BMBX register is active and saves the mailbox job struct
(mboxq) in the mbox_active element of the adapter. The routine then waits
for completion or timeout. The mailbox job struct is not freed by the
routine. In cases of timeout, the adapter will be reset. The
lpfc_sli_mbox_sys_flush() routine will clean up the mbox in preparation for
the reset. It clears the BMBX active flag and marks the job structure as
MBX_NOT_FINISHED. But, it never frees the mboxq job structure. Expectation
in both normal completion and timeout cases is that the issuer of the mbx
command will free the structure. Unfortunately, not all calling paths are
freeing the memory in cases of error.
All calling paths were looked at and updated, if missing, to free the mboxq
memory regardless of completion status.
Link: https://lore.kernel.org/r/20210412013127.2387-7-jsmart2021@gmail.com Co-developed-by: Justin Tee <justin.tee@broadcom.com> Signed-off-by: Justin Tee <justin.tee@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Fix a crash caused by a double put on the node when the driver completed an
ACC for an unsolicted abort on the same node. The second put was executed
by lpfc_nlp_not_used() and is wrong because the completion routine executes
the nlp_put when the iocbq was released. Additionally, the driver is
issuing a LOGO then immediately calls lpfc_nlp_set_state to put the node
into NPR. This call does nothing.
Remove the lpfc_nlp_not_used call and additional set_state in the
completion routine. Remove the lpfc_nlp_set_state post issue_logo. Isn't
necessary.
Link: https://lore.kernel.org/r/20210412013127.2387-3-jsmart2021@gmail.com Co-developed-by: Justin Tee <justin.tee@broadcom.com> Signed-off-by: Justin Tee <justin.tee@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Signed-off-by: Guchun Chen <guchun.chen@amd.com> Acked-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
clang points out that the %hu format string does not match the type
of the variables here:
drivers/gpu/drm/amd/amdgpu/amdgpu_uvd.c:263:7: warning: format specifies type 'unsigned short' but the argument has type 'unsigned int' [-Wformat]
version_major, version_minor);
^~~~~~~~~~~~~
include/drm/drm_print.h:498:19: note: expanded from macro 'DRM_ERROR'
__drm_err(fmt, ##__VA_ARGS__)
~~~ ^~~~~~~~~~~
Change it to a regular %u, the same way a previous patch did for
another instance of the same warning.
Reviewed-by: Christian König <christian.koenig@amd.com> Reviewed-by: Tom Rix <trix@redhat.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Neither vtotal nor drm_mode_vrefresh contain a value that is
premultiplied by 100 making the x100 variable name incorrect and
resulting in vclks_line to become 100 times larger than it is supposed
to be. The hardware counts 100 clockticks too many before tearcheck,
leading to severe panel issues on at least the Sony Xperia lineup.
This is likely an artifact from the original MDSS DSI panel driver where
the calculation [1] corrected for a premultiplied reference framerate by
100 [2]. It does not appear that the above values were ever
premultiplied in the history of the DRM MDP5 driver.
With this change applied the value written to the SYNC_CONFIG_VSYNC
register is now identical to downstream kernels.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org> Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org> Link: https://lore.kernel.org/r/20210406214726.131534-3-marijn.suijten@somainline.org Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Leaving this at a close-to-maximum register value 0xFFF0 means it takes
very long for the MDSS to generate a software vsync interrupt when the
hardware TE interrupt doesn't arrive. Configuring this to double the
vtotal (like some downstream kernels) leads to a frame to take at most
twice before the vsync signal, until hardware TE comes up.
In this case the hardware interrupt responsible for providing this
signal - "disp-te" gpio - is not hooked up to the mdp5 vsync/pp logic at
all. This solves severe panel update issues observed on at least the
Xperia Loire and Tone series, until said gpio is properly hooked up to
an irq.
Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org> Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org> Link: https://lore.kernel.org/r/20210406214726.131534-2-marijn.suijten@somainline.org Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
During load balance, LBF_SOME_PINNED will be set if any candidate task
cannot be detached due to CPU affinity constraints. This can result in
setting env->sd->parent->sgc->group_imbalance, which can lead to a group
being classified as group_imbalanced (rather than any of the other, lower
group_type) when balancing at a higher level.
In workloads involving a single task per CPU, LBF_SOME_PINNED can often be
set due to per-CPU kthreads being the only other runnable tasks on any
given rq. This results in changing the group classification during
load-balance at higher levels when in reality there is nothing that can be
done for this affinity constraint: per-CPU kthreads, as the name implies,
don't get to move around (modulo hotplug shenanigans).
It's not as clear for userspace tasks - a task could be in an N-CPU cpuset
with N-1 offline CPUs, making it an "accidental" per-CPU task rather than
an intended one. KTHREAD_IS_PER_CPU gives us an indisputable signal which
we can leverage here to not set LBF_SOME_PINNED.
Note that the aforementioned classification to group_imbalance (when
nothing can be done) is especially problematic on big.LITTLE systems, which
have a topology the likes of:
Here, setting LBF_SOME_PINNED due to a per-CPU kthread when balancing at MC
level on CPUs [0-1] will subsequently prevent CPUs [2-3] from classifying
the [0-1] group as group_misfit_task when balancing at DIE level. Thus, if
CPUs [0-1] are running CPU-bound (misfit) tasks, ill-timed per-CPU kthreads
can significantly delay the upgmigration of said misfit tasks. Systems
relying on ASYM_PACKING are likely to face similar issues.
Signed-off-by: Lingutla Chandrasekhar <clingutla@codeaurora.org>
[Use kthread_is_per_cpu() rather than p->nr_cpus_allowed]
[Reword changelog] Signed-off-by: Valentin Schneider <valentin.schneider@arm.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Dietmar Eggemann <dietmar.eggemann@arm.com> Reviewed-by: Vincent Guittot <vincent.guittot@linaro.org> Link: https://lkml.kernel.org/r/20210407220628.3798191-2-valentin.schneider@arm.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
For two of the supported sensors the stv06xx driver allocates memory which
is stored in sd->sensor_priv. This memory is freed on a disconnect, but if
the probe() fails, then it isn't freed and so this leaks memory.
Add a new probe_error() op that drivers can use to free any allocated
memory in case there was a probe failure.
Thanks to Pavel Skripkin <paskripkin@gmail.com> for discovering the cause
of the memory leak.
Reported-and-tested-by: syzbot+e7f4c64a4248a0340c37@syzkaller.appspotmail.com Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
In case of error in dvb_usb_adapter_dvb_init() or
dvb_usb_adapter_dvb_init() d->num_adapters_initialized won't be
incremented, but dvb_usb_adapter_exit() relies on it:
for (n = 0; n < d->num_adapters_initialized; n++)
So, allocated objects won't be freed.
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Reported-by: syzbot+3c2be7424cea3b932b0e@syzkaller.appspotmail.com Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
pm_runtime_get_sync() will increase the runtime PM counter
even it returns an error. Thus a pairing decrement is needed
to prevent refcount leak. Fix this by replacing this API with
pm_runtime_resume_and_get(), which will not change the runtime
PM counter on error.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
This driver's remove path calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This means
that the callback function may still be running after the driver's
remove function has finished, which would result in a use-after-free.
Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
This driver's remove path calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This means
that the callback function may still be running after the driver's
remove function has finished, which would result in a use-after-free.
Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
This driver's remove path calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This means
that the callback function may still be running after the driver's
remove function has finished, which would result in a use-after-free.
Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
This driver's remove path calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This means
that the callback function may still be running after the driver's
remove function has finished, which would result in a use-after-free.
Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
This driver's remove path calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This means
that the callback function may still be running after the driver's
remove function has finished, which would result in a use-after-free.
Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
This driver's remove path calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This means
that the callback function may still be running after the driver's
remove function has finished, which would result in a use-after-free.
Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
This driver's remove path calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This means
that the callback function may still be running after the driver's
remove function has finished, which would result in a use-after-free.
Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
There is an error return path that is not kfree'ing socfpga_clk leading
to a memory leak. Fix this by adding in the missing kfree call.
Addresses-Coverity: ("Resource leak") Signed-off-by: Colin Ian King <colin.king@canonical.com> Link: https://lore.kernel.org/r/20210406170115.430990-1-colin.king@canonical.com Acked-by: Dinh Nguyen <dinguyen@kernel.org> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The EDID had a few mistakes as reported by edid-decode:
Block 1, CTA-861 Extension Block:
Video Data Block: For improved preferred timing interoperability, set 'Native detailed modes' to 1.
Video Capability Data Block: S_PT is equal to S_IT and S_CE, so should be set to 0 instead.
Fixed those.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
If some error occurs, URB buffers should also be freed. If they aren't
freed with the dvb here, the em28xx_dvb_fini call doesn't frees the URB
buffers as dvb is set to NULL. The function in which error occurs should
do all the cleanup for the allocations it had done.
Tested the patch with the reproducer provided by syzbot. This patch
fixes the memleak.
Reported-by: syzbot+889397c820fa56adf25d@syzkaller.appspotmail.com Signed-off-by: Muhammad Usama Anjum <musamaanjum@gmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Some arrays return ILLEGAL_REQUEST with ASC 00h if they don't support the
RTPG extended header so remove the check for INVALID FIELD IN CDB.
Link: https://lore.kernel.org/r/20210331201154.20348-1-emilne@redhat.com Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Ewan D. Milne <emilne@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Link: https://lore.kernel.org/r/161549386882.25025.2594251735886014958.stgit@brunhilda Reviewed-by: Scott Benesh <scott.benesh@microchip.com> Reviewed-by: Scott Teel <scott.teel@microchip.com> Acked-by: Martin Wilck <mwilck@suse.com> Signed-off-by: Kevin Barnett <kevin.barnett@microchip.com> Signed-off-by: Don Brace <don.brace@microchip.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
While failing queued I/Os in TMF path, there was a request leak and hence
stale entries in request pool with ref count being non-zero. In shutdown
path we have a BUG_ON to catch stuck I/O either in firmware or in the
driver. The stale requests caused a system crash. The I/O request pool
leakage also lead to a significant performance drop.
Link: https://lore.kernel.org/r/161549370379.25025.12793264112620796062.stgit@brunhilda Reviewed-by: Scott Teel <scott.teel@microchip.com> Reviewed-by: Scott Benesh <scott.benesh@microchip.com> Reviewed-by: Kevin Barnett <kevin.barnett@microchip.com> Signed-off-by: Murthy Bhat <Murthy.Bhat@microchip.com> Signed-off-by: Don Brace <don.brace@microchip.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
On Hisilicon Kunpeng920, ESP is set to 1 by default for all ports of
SATA controller. In some scenarios, some ports are not external SATA ports,
and it cause disks connected to these ports to be identified as removable
disks. So disable the SXS capability on the software side to prevent users
from mistakenly considering non-removable disks as removable disks and
performing related operations.
Signed-off-by: Xingui Yang <yangxingui@huawei.com> Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com> Reviewed-by: John Garry <john.garry@huawei.com> Link: https://lore.kernel.org/r/1615544676-61926-1-git-send-email-luojiaxing@huawei.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
On bsg command completion, bsg_job_done() was called while qla driver
continued to access the bsg_job buffer. bsg_job_done() would free up
resources that ended up being reused by other task while the driver
continued to access the buffers. As a result, driver was reading garbage
data.
vkms_vblank_simulate() uses WARN_ON for timing-dependent condition
(timer overrun). This is a mis-use of WARN_ON, WARN_ON must be used
to denote kernel bugs. Use pr_warn() instead.
CID 361199 (#1 of 1): Unchecked return value (CHECKED_RETURN)
3. check_return: Calling qla24xx_get_isp_stats without checking return
value (as is done elsewhere 4 out of 5 times).
Link: https://lore.kernel.org/r/20210320232359.941-7-bvanassche@acm.org Cc: Quinn Tran <qutran@marvell.com> Cc: Mike Christie <michael.christie@oracle.com> Cc: Himanshu Madhani <himanshu.madhani@oracle.com> Cc: Daniel Wagner <dwagner@suse.de> Cc: Lee Duncan <lduncan@suse.com> Reviewed-by: Daniel Wagner <dwagner@suse.de> Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com> Signed-off-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
[Why]
dc_cursor_position do not initialise position.translate_by_source when
crtc or plane->state->fb is NULL. UBSAN caught this error in
dce110_set_cursor_position, as the value was garbage.
[How]
Initialise dc_cursor_position structure elements to 0 in handle_cursor_update
before calling get_cursor_position.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1471 Reported-by: Lyude Paul <lyude@redhat.com> Signed-off-by: Anson Jacob <Anson.Jacob@amd.com> Reviewed-by: Aurabindo Jayamohanan Pillai <Aurabindo.Pillai@amd.com> Acked-by: Solomon Chiu <solomon.chiu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
This recent change introduce SDMA interrupt info printing with irq->process function.
These functions do not require a set function to enable/disable the irq
Signed-off-by: shaoyunl <shaoyun.liu@amd.com> Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
If get_num_sdma_queues or get_num_xgmi_sdma_queues is 0, we end up
doing a shift operation where the number of bits shifted equals
number of bits in the operand. This behaviour is undefined.
Set num_sdma_queues or num_xgmi_sdma_queues to ULLONG_MAX, if the
count is >= number of bits in the operand.
Reported-by: Lyude Paul <lyude@redhat.com> Signed-off-by: Anson Jacob <Anson.Jacob@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com> Tested-by: Lyude Paul <lyude@redhat.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The psp supplies the link type in the upper 2 bits of the psp xgmi node
information num_hops field. With a new link type, Aldebaran has these
bits set to a non-zero value (1 = xGMI3) so the KFD topology will report
the incorrect IO link weights without proper masking.
The actual number of hops is located in the 3 least significant bits of
this field so mask if off accordingly before passing it to the KFD.
Signed-off-by: Jonathan Kim <jonathan.kim@amd.com> Reviewed-by: Amber Lin <amber.lin@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Add a fix for the memory leak bugs that can occur when the
saa7164_encoder_register() function fails.
The function allocates memory without explicitly freeing
it when errors occur.
Add a better error handling that deallocate the unused buffers before the
function exits during a fail.
Signed-off-by: Daniel Niv <danielniv3@gmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
We must free/disable all interrupts and cancel all pending works
before doing further cleanup.
Before this commit arizona_extcon_remove() was doing several
register writes to shut things down before disabling the IRQs
and it was cancelling only 1 of the 3 different works used.
Move all the register-writes shutting things down to after
the disabling of the IRQs and add the 2 missing
cancel_delayed_work_sync() calls.
This fixes various possible races on driver unbind. One of which
would always trigger on devices using the mic-clamp feature for
jack detection. The ARIZONA_MICD_CLAMP_MODE_MASK update was
done before disabling the IRQs, causing:
1. arizona_jackdet() to run
2. detect a jack being inserted (clamp disabled means jack inserted)
3. call arizona_start_mic() which:
3.1 Enables the MICVDD regulator
3.2 takes a pm_runtime_reference
And this was all happening after the ARIZONA_MICD_ENA bit clearing,
which would undo 3.1 and 3.2 because the ARIZONA_MICD_CLAMP_MODE_MASK
update was being done after the ARIZONA_MICD_ENA bit clearing.
So this means that arizona_extcon_remove() would exit with
1. MICVDD enabled and 2. The pm_runtime_reference being unbalanced.
MICVDD still being enabled caused the following oops when the
regulator is released by the devm framework:
Note this oops is just one of various theoretically possible races caused
by the wrong ordering inside arizona_extcon_remove(), this fixes the
ordering fixing all possible races, including the reported oops.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com> Tested-by: Charles Keepax <ckeepax@opensource.cirrus.com> Acked-by: Chanwoo Choi <cw00.choi@samsung.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When the jack is partially inserted and then removed again it may be
removed while the hpdet code is running. In this case the following
may happen:
1. The "JACKDET rise" or ""JACKDET fall" IRQ triggers
2. arizona_jackdet runs and takes info->lock
3. The "HPDET" IRQ triggers
4. arizona_hpdet_irq runs, blocks on info->lock
5. arizona_jackdet calls arizona_stop_mic() and clears info->hpdet_done
6. arizona_jackdet releases info->lock
7. arizona_hpdet_irq now can continue running and:
7.1 Calls arizona_start_mic() (if a mic was detected)
7.2 sets info->hpdet_done
Step 7 is undesirable / a bug:
7.1 causes the device to stay in a high power-state (with MICVDD enabled)
7.2 causes hpdet to not run on the next jack insertion, which in turn
causes the EXTCON_JACK_HEADPHONE state to never get set
This fixes both issues by skipping these 2 steps when arizona_hpdet_irq
runs after the jack has been unplugged.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com> Tested-by: Charles Keepax <ckeepax@opensource.cirrus.com> Acked-by: Chanwoo Choi <cw00.choi@samsung.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
On all newer bq27xxx ICs, the AveragePower register contains a signed
value; in addition to handling the raw value as unsigned, the driver
code also didn't convert it to µW as expected.
At least for the BQ28Z610, the reference manual incorrectly states that
the value is in units of 1mW and not 10mW. I have no way of knowing
whether the manuals of other supported ICs contain the same error, or if
there are models that actually use 1mW. At least, the new code shouldn't
be *less* correct than the old version for any device.
power_avg is removed from the cache structure, se we don't have to
extend it to store both a signed value and an error code. Always getting
an up-to-date value may be desirable anyways, as it avoids inconsistent
current and power readings when switching between charging and
discharging.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The correct return code to report an invalid pipeline configuration is
-EPIPE. Return it instead of -EINVAL from __capture_legacy_try_fmt()
when the capture format doesn't match the media bus format of the
connected subdev.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Rui Miguel Silva <rmfrfs@gmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
This fixes a compilation warning in pscsi_complete_cmd():
drivers/target/target_core_pscsi.c: In function ‘pscsi_complete_cmd’:
drivers/target/target_core_pscsi.c:624:5: warning: suggest braces around empty body in an ‘if’ statement [-Wempty-body]
; /* XXX: TCM_LOGICAL_UNIT_COMMUNICATION_FAILURE */
Link: https://lore.kernel.org/r/20210228055645.22253-5-chaitanya.kulkarni@wdc.com Reviewed-by: Mike Christie <michael.christie@oracle.com> Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
On a pt2pt setup, between 2 initiators, if one side issues a a LOGO, there
is no relogin attempt. The FC specs are grey in this area on which port
(higher wwn or not) is to re-login.
As there is no spec guidance, unconditionally re-PLOGI after the logout to
ensure a login is re-established.
Link: https://lore.kernel.org/r/20210301171821.3427-8-jsmart2021@gmail.com Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The wqe_dbde field indicates whether a Data BDE is present in Words 0:2 and
should therefore should be clear in the abts request wqe. By setting the
bit we can be misleading fw into error cases.
Clear the wqe_dbde field.
Link: https://lore.kernel.org/r/20210301171821.3427-2-jsmart2021@gmail.com Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
[Why]
There is a window of time where we optimize bandwidth due to no streams
enabled will enable PSTATE changing but HUBPs are not disabled yet.
This results in underflow counter increasing in some hotplug scenarios.
[How]
Set the optimize-bandwidth flag for later processing once all the HUBPs
are properly disabled.
Signed-off-by: Aric Cyr <aric.cyr@amd.com> Acked-by: Bindu Ramamurthy <bindu.r@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
[why]
This check for ASIC revision is no longer useful and causes
lightup issues after a topology change in MST DSC scenario.
In this case, DSC configs should be recalculated for the new
topology. This check prevented that from happening on certain
ASICs that do, in fact, support DSC.
[how]
Change the ASIC revision to instead check if DSC is supported.
Signed-off-by: Eryk Brol <eryk.brol@amd.com> Acked-by: Bindu Ramamurthy <bindu.r@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The OneGX1 Pro has a fairly unique combination of generic strings,
but we additionally match on the BIOS date just to be safe.
Signed-off-by: Jared Baldridge <jrb@expunge.us> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/41288ccb-1012-486b-81c1-a24c31850c91@www.fastmail.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The DMI callbacks, used for quirks, currently access the PMC by getting
the address a global pmc_dev struct. Instead, have the callbacks set a
global quirk specific variable. In probe, after calling dmi_check_system(),
pass pmc_dev to a function that will handle each quirk if its variable
condition is met. This allows removing the global pmc_dev later.
Signed-off-by: David E. Box <david.e.box@linux.intel.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Rajneesh Bhardwaj <irenic.rajneesh@gmail.com> Link: https://lore.kernel.org/r/20210417031252.3020837-2-david.e.box@linux.intel.com Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
pm_runtime_get_sync will increment pm usage counter even it failed.
Forgetting to putting operation will result in reference leak here.
Fix it by replacing it with pm_runtime_resume_and_get to keep usage
counter balanced.
Signed-off-by: Shixin Liu <liushixin2@huawei.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
pm_runtime_get_sync will increment pm usage counter even it failed.
Forgetting to putting operation will result in reference leak here.
Fix it by replacing it with pm_runtime_resume_and_get to keep usage
counter balanced.
Signed-off-by: Shixin Liu <liushixin2@huawei.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
pm_runtime_get_sync will increment pm usage counter even it failed.
Forgetting to putting operation will result in reference leak here.
Fix it by replacing it with pm_runtime_resume_and_get to keep usage
counter balanced.
Signed-off-by: Shixin Liu <liushixin2@huawei.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
This driver's remove path calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This means
that the callback function may still be running after the driver's
remove function has finished, which would result in a use-after-free.
Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Link: https://lore.kernel.org/r/20210407092716.3270248-1-yangyingliang@huawei.com Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
pm_runtime_get_sync will increment pm usage counter even it failed.
thus a pairing decrement is needed.
Fix it by replacing it with pm_runtime_resume_and_get to keep usage
counter balanced.
Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Bixuan Cui <cuibixuan@huawei.com> Link: https://lore.kernel.org/r/20210408130831.56239-1-cuibixuan@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
pm_runtime_get_sync will increment pm usage counter even it failed.
thus a pairing decrement is needed.
Fix it by replacing it with pm_runtime_resume_and_get to keep usage
counter balanced.
Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Bixuan Cui <cuibixuan@huawei.com> Link: https://lore.kernel.org/r/20210408091836.55227-1-cuibixuan@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
pm_runtime_get_sync will increment pm usage counter even it failed.
Forgetting to putting operation will result in reference leak here.
Fix it by replacing it with pm_runtime_resume_and_get to keep usage
counter balanced.
Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wang Li <wangli74@huawei.com> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Link: https://lore.kernel.org/r/20210409095458.29921-1-wangli74@huawei.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Call spi_master_get() holds the reference count to master device, thus
we need an additional spi_master_put() call to reduce the reference
count, otherwise we will leak a reference to master.
This commit fix it by removing the unnecessary spi_master_get().
Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Link: https://lore.kernel.org/r/20210409082954.2906933-1-weiyongjun1@huawei.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Call spi_master_get() holds the reference count to master device, thus
we need an additional spi_master_put() call to reduce the reference
count, otherwise we will leak a reference to master.
This commit fix it by removing the unnecessary spi_master_get().
Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Link: https://lore.kernel.org/r/20210409082955.2907950-1-weiyongjun1@huawei.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The Max Interrupters supported by the controller is given in a 10bit
wide bitfield, but the driver uses a fixed 128 size array to index these
interrupters.
Klockwork reports a possible array out of bounds case which in theory
is possible. In practice this hasn't been hit as a common number of Max
Interrupters for new controllers is 8, not even close to 128.
When Secure World returns, it may have changed the size attribute of the
memory references passed as [in/out] parameters. The GlobalPlatform TEE
Internal Core API specification does not restrict the values that this
size can take. In particular, Secure World may increase the value to be
larger than the size of the input buffer to indicate that it needs more.
Therefore, the size check in optee_from_msg_param() is incorrect and
needs to be removed. This fixes a number of failed test cases in the
GlobalPlatform TEE Initial Configuratiom Test Suite v2_0_0_0-2017_06_09
when OP-TEE is compiled without dynamic shared memory support
(CFG_CORE_DYN_SHM=n).
When cross-compiling with Clang, the `$(CLANG_FLAGS)' variable
contains additional flags needed to build C and assembly sources
for the target platform. Normally this variable is automatically
included in `$(KBUILD_CFLAGS)' via the top-level Makefile.
The x86 real-mode makefile builds `$(REALMODE_CFLAGS)' from a
plain assignment and therefore drops the Clang flags. This causes
Clang to not recognize x86-specific assembler directives:
Explicit propagation of `$(CLANG_FLAGS)' to `$(REALMODE_CFLAGS)',
which is inherited by real-mode make rules, fixes cross-compilation
with Clang for x86 targets.
Relevant flags:
* `--target' sets the target architecture when cross-compiling. This
flag must be set for both compilation and assembly (`KBUILD_AFLAGS')
to support architecture-specific assembler directives.
* `-no-integrated-as' tells clang to assemble with GNU Assembler
instead of its built-in LLVM assembler. This flag is set by default
unless `LLVM_IAS=1' is set, because the LLVM assembler can't yet
parse certain GNU extensions.
It should not be necessary to update the current_state field of
struct pci_dev in pci_enable_device_flags() before calling
do_pci_enable_device() for the device, because none of the
code between that point and the pci_set_power_state() call in
do_pci_enable_device() invoked later depends on it.
Moreover, doing that is actively harmful in some cases. For example,
if the given PCI device depends on an ACPI power resource whose _STA
method initially returns 0 ("off"), but the config space of the PCI
device is accessible and the power state retrieved from the
PCI_PM_CTRL register is D0, the current_state field in the struct
pci_dev representing that device will get out of sync with the
power.state of its ACPI companion object and that will lead to
power management issues going forward.
To avoid such issues it is better to leave the current_state value
as is until it is changed to PCI_D0 by do_pci_enable_device() as
appropriate. However, the power state of the device is not changed
to PCI_D0 if it is already enabled when pci_enable_device_flags()
gets called for it, so update its current_state in that case, but
use pci_update_current_state() covering platform PM too for that.
Link: https://lore.kernel.org/lkml/20210314000439.3138941-1-luzmaximilian@gmail.com/ Reported-by: Maximilian Luz <luzmaximilian@gmail.com> Tested-by: Maximilian Luz <luzmaximilian@gmail.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Some hosts incorrectly use sub-minor version for minor version (i.e.
0x02 instead of 0x20 for bcdUSB 0x320 and 0x01 for bcdUSB 0x310).
Currently the xHCI driver works around this by just checking for minor
revision > 0x01 for USB 3.1 everywhere. With the addition of USB 3.2,
checking this gets a bit cumbersome. Since there is no USB release with
bcdUSB 0x301 to 0x309, we can assume that sub-minor version 01 to 09 is
incorrect. Let's try to fix this and use the minor revision that matches
with the USB/xHCI spec to help with the version checking within the
driver.
The current dwc3_gadget_reset_interrupt() will stop any active
transfers, but only addresses blocking of EP queuing for while we are
coming from a disconnected scenario, i.e. after receiving the disconnect
event. If the host decides to issue a bus reset on the device, the
connected parameter will still be set to true, allowing for EP queuing
to continue while we are disabling the functions. To avoid this, set the
connected flag to false until the stop active transfers is complete.
Currently user can configure UAC1 function with
parameters that violate UAC1 spec or are not supported
by UAC1 gadget implementation.
This can lead to incorrect behavior if such gadget
is connected to the host - like enumeration failure
or other issues depending on host's UAC1 driver
implementation, bringing user to a long hours
of debugging the issue.
Instead of silently accept these parameters, throw
an error if they are not valid.
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com> Link: https://lore.kernel.org/r/1614599375-8803-5-git-send-email-ruslan.bilovol@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Currently user can configure UAC2 function with
parameters that violate UAC2 spec or are not supported
by UAC2 gadget implementation.
This can lead to incorrect behavior if such gadget
is connected to the host - like enumeration failure
or other issues depending on host's UAC2 driver
implementation, bringing user to a long hours
of debugging the issue.
Instead of silently accept these parameters, throw
an error if they are not valid.
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com> Link: https://lore.kernel.org/r/1614599375-8803-4-git-send-email-ruslan.bilovol@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When irq_matrix_free() is called for an unallocated vector the
managed_allocated and total_allocated counters get out of sync with the
real state of the matrix. Later, when the last interrupt is freed, these
counters will underflow resulting in UINTMAX because the counters are
unsigned.
While this is certainly a problem of the calling code, this can be catched
in the allocator by checking the allocation bit for the to be freed vector
which simplifies debugging.
An example of the problem described above:
https://lore.kernel.org/lkml/20210318192819.636943062@linutronix.de/
Add the missing sanity check and emit a warning when it triggers.
Suggested-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lore.kernel.org/r/20210319111823.1105248-1-vkuznets@redhat.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
According with USB Device Class Definition for Video Device the
Processing Unit Descriptor bLength should be 12 (10 + bmControlSize),
but it has 11.
Invalid length caused that Processing Unit Descriptor Test Video form
CV tool failed. To fix this issue patch adds bmVideoStandards into
uvc_processing_unit_descriptor structure.
The bmVideoStandards field was added in UVC 1.1 and it wasn't part of
UVC 1.0a.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Pawel Laszczak <pawell@cadence.com> Reviewed-by: Peter Chen <peter.chen@kernel.org> Link: https://lore.kernel.org/r/20210315071748.29706-1-pawell@gli-login.cadence.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Patch adds extra checking for bInterval passed by configfs.
The 5.6.4 chapter of USB Specification (rev. 2.0) say:
"A high-bandwidth endpoint must specify a period of 1x125 µs
(i.e., a bInterval value of 1)."
The issue was observed during testing UVC class on CV.
I treat this change as improvement because we can control
bInterval by configfs.
Reviewed-by: Peter Chen <peter.chen@kernel.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Pawel Laszczak <pawell@cadence.com> Link: https://lore.kernel.org/r/20210308125338.4824-1-pawell@gli-login.cadence.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Given that crypto_alloc_tfm() may return ERR pointers, and to avoid
crashes on obscure error paths where such pointers are presented to
crypto_destroy_tfm() (such as [0]), add an ERR_PTR check there
before dereferencing the second argument as a struct crypto_tfm
pointer.
This removes the assignment of setup and cleanup functions for the ath79
target. Assigning the setup-method will lead to 'setup_transfer' not
being assigned in spi_bitbang_init. Because of this, performing any
TX/RX operation will lead to a kernel oops.
Also drop the redundant cleanup assignment, as it's also assigned in
spi_bitbang_init.
Signed-off-by: David Bauer <mail@david-bauer.net> Link: https://lore.kernel.org/r/20210303160837.165771-2-mail@david-bauer.net Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
spi-bitbang has to call the chipselect function on the ath79 SPI driver
in order to communicate with the SPI slave device, as the ath79 SPI
driver has three dedicated chipselect lines but can also be used with
GPIOs for the CS lines.
Fixes commit 4a07b8bcd503 ("spi: bitbang: Make chipselect callback optional")
Signed-off-by: David Bauer <mail@david-bauer.net> Link: https://lore.kernel.org/r/20210303160837.165771-1-mail@david-bauer.net Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
We want to probe l4_wkup and l4_cfg interconnect devices first to avoid
issues with missing resources. Otherwise we attempt to probe l4_per
devices first causing pointless deferred probe and also annoyingh
renumbering of the MMC devices for example.
Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Use kzalloc() rather than kmalloc() for the dynamically allocated parts
of the colormap in fb_alloc_cmap_gfp, to prevent a leak of random kernel
data to userspace under certain circumstances.
The return value on success (>= 0) is overwritten by the return value of
put_old_timex32(). That works correct in the fault case, but is wrong for
the success case where put_old_timex32() returns 0.
Just check the return value of put_old_timex32() and return -EFAULT in case
it is not zero.
[ tglx: Massage changelog ]
Fixes: 3a4d44b61625 ("ntp: Move adjtimex related compat syscalls to native counterparts") Signed-off-by: Chen Jun <chenjun102@huawei.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Richard Cochran <richardcochran@gmail.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20210414030449.90692-1-chenjun102@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When creating a subvolume we allocate an extent buffer for its root node
after starting a transaction. We setup a root item for the subvolume that
points to that extent buffer and then attempt to insert the root item into
the root tree - however if that fails, due to ENOMEM for example, we do
not free the extent buffer previously allocated and we do not abort the
transaction (as at that point we did nothing that can not be undone).
This means that we effectively do not return the metadata extent back to
the free space cache/tree and we leave a delayed reference for it which
causes a metadata extent item to be added to the extent tree, in the next
transaction commit, without having backreferences. When this happens
'btrfs check' reports the following:
$ btrfs check /dev/sdi
Opening filesystem to check...
Checking filesystem on /dev/sdi
UUID: dce2cb9d-025f-4b05-a4bf-cee0ad3785eb
[1/7] checking root items
[2/7] checking extents
ref mismatch on [30425088 16384] extent item 1, found 0
backref 30425088 root 256 not referenced back 0x564a91c23d70
incorrect global backref count on 30425088 found 1 wanted 0
backpointer mismatch on [30425088 16384]
owner ref check failed [30425088 16384]
ERROR: errors found in extent allocation tree or chunk allocation
[3/7] checking free space cache
[4/7] checking fs roots
[5/7] checking only csums items (without verifying data)
[6/7] checking root refs
[7/7] checking quota groups skipped (not enabled on this FS)
found 212992 bytes used, error(s) found
total csum bytes: 0
total tree bytes: 131072
total fs tree bytes: 32768
total extent tree bytes: 16384
btree space waste bytes: 124669
file data blocks allocated: 65536
referenced 65536
So fix this by freeing the metadata extent if btrfs_insert_root() returns
an error.
CC: stable@vger.kernel.org # 4.4+ Signed-off-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>