As in manpage of migrate_pages, the errno should be set to EINVAL when
none of the node IDs specified by new_nodes are on-line and allowed by
the process's current cpuset context, or none of the specified nodes
contain memory. However, when test by following case:
The ret will be 0 and no errno is set. As the new_nodes is empty, we
should expect EINVAL as documented.
To fix the case like above, this patch check whether target nodes AND
current task_nodes is empty, and then check whether AND
node_states[N_MEMORY] is empty.
The new nodes specifies one or more node IDs that are greater than the
maximum supported node ID, however, the errno is not set to EINVAL as
expected.
As man pages of set_mempolicy[1], mbind[2], and migrate_pages[3]
mentioned, when nodemask specifies one or more node IDs that are greater
than the maximum supported node ID, the errno should set to EINVAL.
However, get_nodes only check whether the part of bits
[BITS_PER_LONG*BITS_TO_LONGS(MAX_NUMNODES), maxnode) is zero or not, and
remain [MAX_NUMNODES, BITS_PER_LONG*BITS_TO_LONGS(MAX_NUMNODES)
unchecked.
This patch is to check the bits of [MAX_NUMNODES, maxnode) in get_nodes
to let migrate_pages set the errno to EINVAL when nodemask specifies one
or more node IDs that are greater than the maximum supported node ID,
which follows the manpage's guide.
We should not reuse the dirty bh in jbd2 directly due to the following
situation:
1. When removing extent rec, we will dirty the bhs of extent rec and
truncate log at the same time, and hand them over to jbd2.
2. The bhs are submitted to jbd2 area successfully.
3. The write-back thread of device help flush the bhs to disk but
encounter write error due to abnormal storage link.
4. After a while the storage link become normal. Truncate log flush
worker triggered by the next space reclaiming found the dirty bh of
truncate log and clear its 'BH_Write_EIO' and then set it uptodate in
__ocfs2_journal_access():
ocfs2_truncate_log_worker
ocfs2_flush_truncate_log
__ocfs2_flush_truncate_log
ocfs2_replay_truncate_records
ocfs2_journal_access_di
__ocfs2_journal_access // here we clear io_error and set 'tl_bh' uptodata.
5. Then jbd2 will flush the bh of truncate log to disk, but the bh of
extent rec is still in error state, and unfortunately nobody will
take care of it.
6. At last the space of extent rec was not reduced, but truncate log
flush worker have given it back to globalalloc. That will cause
duplicate cluster problem which could be identified by fsck.ocfs2.
Sadly we can hardly revert this but set fs read-only in case of ruining
atomicity and consistency of space reclaim.
Link: http://lkml.kernel.org/r/5A6E8092.8090701@huawei.com Fixes: acf8fdbe6afb ("ocfs2: do not BUG if buffer not uptodate in __ocfs2_journal_access") Signed-off-by: Jun Piao <piaojun@huawei.com> Reviewed-by: Yiwen Jiang <jiangyiwen@huawei.com> Reviewed-by: Changwei Ge <ge.changwei@h3c.com> Cc: Mark Fasheh <mfasheh@versity.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Joseph Qi <jiangqi903@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In this situation we need return -EROFS to 'mount.ocfs2', so that user
can fix it by fsck. And then mount again. In addition, 'mount.ocfs2'
should be updated correspondingly as it only return 1 for all errno.
And I will post a patch for 'mount.ocfs2' too.
Link: http://lkml.kernel.org/r/5A4302FA.2010606@huawei.com Signed-off-by: Jun Piao <piaojun@huawei.com> Reviewed-by: Alex Chen <alex.chen@huawei.com> Reviewed-by: Joseph Qi <jiangqi903@gmail.com> Reviewed-by: Changwei Ge <ge.changwei@h3c.com> Reviewed-by: Gang He <ghe@suse.com> Cc: Mark Fasheh <mfasheh@versity.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
I was investigating an issue with seabios >= 1.10 which stopped working
for nested KVM on Hyper-V. The problem appears to be in
handle_ept_violation() function: when we do fast mmio we need to skip
the instruction so we do kvm_skip_emulated_instruction(). This, however,
depends on VM_EXIT_INSTRUCTION_LEN field being set correctly in VMCS.
However, this is not the case.
Intel's manual doesn't mandate VM_EXIT_INSTRUCTION_LEN to be set when
EPT MISCONFIG occurs. While on real hardware it was observed to be set,
some hypervisors follow the spec and don't set it; we end up advancing
IP with some random value.
I checked with Microsoft and they confirmed they don't fill
VM_EXIT_INSTRUCTION_LEN on EPT MISCONFIG.
Fix the issue by doing instruction skip through emulator when running
nested.
Fixes: 68c3b4d1676d870f0453c31d5a52e7e65c7448ae Suggested-by: Radim Krčmář <rkrcmar@redhat.com> Suggested-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Radim Krčmář <rkrcmar@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
For EPT-violations that are triggered by a read, the pages are also mapped with
write permissions (if their memory region is also writable). That would avoid
getting yet another fault on the same page when a write occurs.
This optimization only happens when you have a "struct page" backing the memory
region. So also enable it for memory regions that do not have a "struct page".
Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Radim Krčmář <rkrcmar@redhat.com> Cc: kvm@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by: KarimAllah Ahmed <karahmed@amazon.de> Reviewed-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Radim Krčmář <rkrcmar@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Add suffix ULL to constant 80000 in order to avoid a potential integer
overflow and give the compiler complete information about the proper
arithmetic to use. Notice that this constant is used in a context that
expects an expression of type u64.
The current cast to u64 effectively applies to the whole expression
as an argument of type u64 to be passed to div64_u64, but it does
not prevent it from being evaluated using 32-bit arithmetic instead
of 64-bit arithmetic.
Also, once the expression is properly evaluated using 64-bit arithmentic,
there is no need for the parentheses and the external cast to u64.
Addresses-Coverity-ID: 1357588 ("Unintentional integer overflow") Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Several netfilter matches and targets put kernel pointers into
info objects, but don't set usersize in descriptors.
This leads to kernel pointer leaks if a match/target is set
and then read back to userspace.
Properly set usersize for these matches/targets.
Found with manual code inspection.
Fixes: ec2318904965 ("xtables: extend matches and targets with .usersize") Signed-off-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In hyperv_init() its presumed that it always has access to VP index and
hypercall MSRs while according to the specification it should be checked if
it's allowed to access the corresponding MSRs before accessing them.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Cc: Stephen Hemminger <sthemmin@microsoft.com> Cc: kvm@vger.kernel.org Cc: Radim Krčmář <rkrcmar@redhat.com> Cc: Haiyang Zhang <haiyangz@microsoft.com> Cc: "Michael Kelley (EOSG)" <Michael.H.Kelley@microsoft.com> Cc: Roman Kagan <rkagan@virtuozzo.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: devel@linuxdriverproject.org Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: "K. Y. Srinivasan" <kys@microsoft.com> Cc: Cathy Avery <cavery@redhat.com> Cc: Mohammed Gamal <mmorsy@redhat.com> Link: https://lkml.kernel.org/r/20180124132337.30138-2-vkuznets@redhat.com Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When the frame check sequence (FCS) is split across the last two frames
of a fragmented packet, part of the FCS gets counted twice, once when
subtracting the FCS, and again when subtracting the previously received
data.
For example, if 1602 bytes are received, and the first fragment contains
the first 1600 bytes (including the first two bytes of the FCS), and the
second fragment contains the last two bytes of the FCS:
When using the max_mw_size parameter of ntb_transport to limit the size of
the Memory windows, communication cannot be established and the queues
freeze.
This is because the mw_size that's reported to the peer is correctly
limited but the size used locally is not. So the MW is initialized
with a buffer smaller than the window but the TX side is using the
full window. This means the TX side will be writing to a region of the
window that points nowhere.
This is easily fixed by applying the same limit to tx_size in
ntb_transport_init_queue().
Fixes: e26a5843f7f5 ("NTB: Split ntb_hw_intel and ntb_transport drivers") Signed-off-by: Logan Gunthorpe <logang@deltatee.com> Acked-by: Allen Hubbe <Allen.Hubbe@dell.com> Cc: Dave Jiang <dave.jiang@intel.com> Signed-off-by: Jon Mason <jdmason@kudzu.us> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This patch fixes some problems encountered at runtime with
configurations that support memory-less nodes, or that hot-add CPUs
into nodes that are memoryless during system execution after boot. The
problems of interest include:
* Nodes known to powerpc to be memoryless at boot, but to have CPUs in
them are allowed to be 'possible' and 'online'. Memory allocations
for those nodes are taken from another node that does have memory
until and if memory is hot-added to the node.
* Nodes which have no resources assigned at boot, but which may still
be referenced subsequently by affinity or associativity attributes,
are kept in the list of 'possible' nodes for powerpc. Hot-add of
memory or CPUs to the system can reference these nodes and bring
them online instead of redirecting the references to one of the set
of nodes known to have memory at boot.
Note that this software operates under the context of CPU hotplug. We
are not doing memory hotplug in this code, but rather updating the
kernel's CPU topology (i.e. arch_update_cpu_topology /
numa_update_cpu_topology). We are initializing a node that may be used
by CPUs or memory before it can be referenced as invalid by a CPU
hotplug operation. CPU hotplug operations are protected by a range of
APIs including cpu_maps_update_begin/cpu_maps_update_done,
cpus_read/write_lock / cpus_read/write_unlock, device locks, and more.
Memory hotplug operations, including try_online_node, are protected by
mem_hotplug_begin/mem_hotplug_done, device locks, and more. In the
case of CPUs being hot-added to a previously memoryless node, the
try_online_node operation occurs wholly within the CPU locks with no
overlap. Using HMC hot-add/hot-remove operations, we have been able to
add and remove CPUs to any possible node without failures. HMC
operations involve a degree self-serialization, though.
Signed-off-by: Michael Bringmann <mwb@linux.vnet.ibm.com> Reviewed-by: Nathan Fontenot <nfont@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
On powerpc systems which allow 'hot-add' of CPU or memory resources,
it may occur that the new resources are to be inserted into nodes that
were not used for these resources at bootup. In the kernel, any node
that is used must be defined and initialized. These empty nodes may
occur when,
* Dedicated vs. shared resources. Shared resources require information
such as the VPHN hcall for CPU assignment to nodes. Associativity
decisions made based on dedicated resource rules, such as
associativity properties in the device tree, may vary from decisions
made using the values returned by the VPHN hcall.
* memoryless nodes at boot. Nodes need to be defined as 'possible' at
boot for operation with other code modules. Previously, the powerpc
code would limit the set of possible nodes to those which have
memory assigned at boot, and were thus online. Subsequent add/remove
of CPUs or memory would only work with this subset of possible
nodes.
* memoryless nodes with CPUs at boot. Due to the previous restriction
on nodes, nodes that had CPUs but no memory were being collapsed
into other nodes that did have memory at boot. In practice this
meant that the node assignment presented by the runtime kernel
differed from the affinity and associativity attributes presented by
the device tree or VPHN hcalls. Nodes that might be known to the
pHyp were not 'possible' in the runtime kernel because they did not
have memory at boot.
This patch ensures that sufficient nodes are defined to support
configuration requirements after boot, as well as at boot. This patch
set fixes a couple of problems.
* Nodes known to powerpc to be memoryless at boot, but to have CPUs in
them are allowed to be 'possible' and 'online'. Memory allocations
for those nodes are taken from another node that does have memory
until and if memory is hot-added to the node. * Nodes which have no
resources assigned at boot, but which may still be referenced
subsequently by affinity or associativity attributes, are kept in
the list of 'possible' nodes for powerpc. Hot-add of memory or CPUs
to the system can reference these nodes and bring them online
instead of redirecting to one of the set of nodes that were known to
have memory at boot.
This patch extracts the value of the lowest domain level (number of
allocable resources) from the device tree property
"ibm,max-associativity-domains" to use as the maximum number of nodes
to setup as possibly available in the system. This new setting will
override the instruction:
presently seen in the function arch/powerpc/mm/numa.c:initmem_init().
If the "ibm,max-associativity-domains" property is not present at
boot, no operation will be performed to define or enable additional
nodes, or enable the above 'nodes_and()'.
Signed-off-by: Michael Bringmann <mwb@linux.vnet.ibm.com> Reviewed-by: Nathan Fontenot <nfont@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In commit 36777d9fa24c ("i40e: check current configured input set when
adding ntuple filters") some code was added to report the input set
mask for a given filter when reporting it to the user.
This code is necessary so that the reported filter correctly displays
that it is or is not masking certain fields.
Unfortunately the code was incorrect. Development error accidentally
swapped the mask values for the IPv4 addresses with the L4 port numbers.
The port numbers are only 16bits wide while IPv4 addresses are 32 bits.
Unfortunately we assigned only 16 bits to the IPv4 address masks.
Additionally we assigned 32bit value 0xFFFFFFF to the TCP port numbers.
This second part does not matter as the value would be truncated to
16bits regardless, but it is unnecessary.
Fix the reported masks to properly report that the entire field is
masked.
Fixes: 36777d9fa24c ("i40e: check current configured input set when adding ntuple filters") Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When implementing support for IP_USER_FLOW filters, we correctly
programmed a filter for both the non fragmented IPv4/Other filter, as
well as the fragmented IPv4 filters. However, we did not properly
program the input set for fragmented IPv4 PCTYPE. This meant that the
filters would almost certainly not match, unless the user specified all
of the flow types.
Add support to program the fragmented IPv4 filter input set. Since we
always program these filters together, we'll assume that the two input
sets must match, and will thus always program the input sets to the same
value.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If jffs2_iget() fails for a newly-allocated inode, jffs2_do_clear_inode()
can get called twice in the error handling path, the first call in
jffs2_iget() itself and the second through iget_failed(). This can result
to a use-after-free error in the second jffs2_do_clear_inode() call, such
as shown by the oops below wherein the second jffs2_do_clear_inode() call
was trying to free node fragments that were already freed in the first
jffs2_do_clear_inode() call.
The jffs2_do_clear_inode() call in jffs2_iget() is unnecessary since
iget_failed() will eventually call jffs2_do_clear_inode() if needed, so
just remove it.
Fixes: 5451f79f5f81 ("iget: stop JFFS2 from using iget() and read_inode()") Reviewed-by: Richard Weinberger <richard@nod.at> Signed-off-by: Jake Daryll Obina <jake.obina@gmail.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Returning EOPNOTSUPP is problematic because it can also be
returned by the method function, and we use it in quite a few
places in drivers these days.
Instead, dedicate EPROTONOSUPPORT to indicate that the ioctl framework
is enabled but the requested object and method are not supported by
the kernel. No other case will return this code, and it lets userspace
know to fall back to write().
grep says we do not use it today in drivers/infiniband subsystem.
Exar sleep wake-up handling has been done on a per-channel basis by
virtue of INT0 being accessible from each channel's address space. I
believe this was initially done out of necessity, but now that Exar
devices have their own driver, we can do things more efficiently by
registering a dedicated INT0 handler at the PCI device level.
I see this change providing the following benefits:
1. If more than one port is active, eliminates the redundant bus
cycles for reading INT0 on every interrupt.
2. This note associated with hooking in the per-channel handler in
8250_port.c is resolved:
/* Fixme: probably not the best place for this */
Cc: Matt Schulte <matts@commtech-fastcom.com> Signed-off-by: Aaron Sierra <asierra@xes-inc.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When hypercall-based TLB flush was enabled for Hyper-V guests PCID feature
was deliberately suppressed as a precaution: back then PCID was never
exposed to Hyper-V guests and it wasn't clear what will happen if some day
it becomes available. The day came and PCID/INVPCID features are already
exposed on certain Hyper-V hosts.
>From TLFS (as of 5.0b) it is unclear how TLB flush hypercalls combine with
PCID. In particular the usage of PCID is per-cpu based: the same mm gets
different CR3 values on different CPUs. If the hypercall does exact
matching this will fail. However, this is not the case. David Zhang
explains:
"In practice, the AddressSpace argument is ignored on any VM that supports
PCIDs.
Architecturally, the AddressSpace argument must match the CR3 with PCID
bits stripped out (i.e., the low 12 bits of AddressSpace should be 0 in
long mode). The flush hypercalls flush all PCIDs for the specified
AddressSpace."
With this, PCID can be enabled.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: David Zhang <dazhan@microsoft.com> Cc: Stephen Hemminger <sthemmin@microsoft.com> Cc: Haiyang Zhang <haiyangz@microsoft.com> Cc: "Michael Kelley (EOSG)" <Michael.H.Kelley@microsoft.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: devel@linuxdriverproject.org Cc: "K. Y. Srinivasan" <kys@microsoft.com> Cc: Aditya Bhandari <adityabh@microsoft.com> Link: https://lkml.kernel.org/r/20180124103629.29980-1-vkuznets@redhat.com Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This will remove all previous entries in the VLAN table including those
generated by VLAN interfaces created on the VF. The issue arises when
the VF is under PF VLAN assignment and one or more of these VLAN
interfaces of the VF are deleted. When deleting these VLAN interfaces,
the following message will be generated in "dmesg":
failed to kill vid 0081/<vid> for device <vf>
This is due to the fact that "ndo_vlan_rx_kill_vid" exits with an error.
The handler for this ndo is "fm10k_update_vid". Any calls to this
function while under PF VLAN management will exit prematurely and, thus,
it will generate the failure message.
Additionally, since "fm10k_update_vid" exits prematurely, none of the
VLAN update is performed. So, even though the actual VLAN interfaces of
the VF will be deleted, the active_vlans bitmask is not cleared. When
the VF is no longer under PF VLAN assignment, the driver mistakenly
restores the previous entries of the VLAN table based on an
unsynchronized list of active VLANs.
The solution to this issue involves checking the VLAN update action type
before exiting "fm10k_update_vid". If the VLAN update action type is to
"add", this action will not be permitted while the VF is under PF VLAN
assignment and the VLAN update is abandoned like before.
However, if the VLAN update action type is to "kill", then we need to
also clear the active_vlans bitmask. However, we don't need to actually
queue any messages to the PF, because the MAC and VLAN tables have
already been cleared, and the PF would silently ignore these requests
anyways.
Problem description:
After ethernet cable connect and disconnect for several iterations on a
device with i210, tx timestamp will stop being put into the socket.
Steps to reproduce:
1. Setup a device with i210 and wire it to a 802.1AS capable switch (
Extreme Networks Summit x440 is used in our case)
2. Have the gptp daemon running on the device and make sure it is synced
with the switch
3. Have the switch disable and enable the port, wait for the device gets
resynced with the switch
4. Iterates step 3 until the device is not albe to get resynced
5. Review the log in dmesg and you will see warning message "igb : clearing
Tx timestamp hang"
Root cause:
If ptp_tx_work() gets scheduled just before the port gets disabled, a LINK
DOWN event will be processed before ptp_tx_work(), which may cause timeout
in ptp_tx_work(). In the timeout logic, the TSYNCTXCTL's TXTT bit (Transmit
timestamp valid bit) is not cleared, causing no new timestamp loaded to
TXSTMP register. Consequently therefore, no new interrupt is triggerred by
TSICR.TXTS bit and no more Tx timestamp send to the socket.
Signed-off-by: Daniel Hua <daniel.hua@ni.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Before libvirt modifies the MAC address and vlan tag for an SRIOV VF
for use by a virtual machine (either using vfio device assignment or
macvtap passthru mode), it saves the current MAC address and vlan tag
so that it can reset them to their original value when the guest is
done. Libvirt can't leave the VF MAC set to the value used by the
now-defunct guest since it may be started again later using a
different VF, but it certainly shouldn't just pick any random value,
either. So it saves the state of everything prior to using the VF, and
resets it to that.
The igb driver initializes the MAC addresses of all VFs to
00:00:00:00:00:00, and reports that when asked (via an RTM_GETLINK
netlink message, also visible in the list of VFs in the output of "ip
link show"). But when libvirt attempts to restore the MAC address back
to 00:00:00:00:00:00 (using an RTM_SETLINK netlink message) the kernel
responds with "Invalid argument".
Forbidding a reset back to the original value leaves the VF MAC at the
value set for the now-defunct virtual machine. Especially on a system
with NetworkManager enabled, this has very bad consequences, since
NetworkManager forces all interfacess to be IFF_UP all the time - if
the same virtual machine is restarted using a different VF (or even on
a different host), there will be multiple interfaces watching for
traffic with the same MAC address.
To allow libvirt to revert to the original state, we need a way to
remove the administrative set MAC on a VF, to allow normal host
operation again, and to reset/overwrite the VF MAC via VF netdev.
This patch implements the outlined scenario by allowing to set the
VF MAC to 00:00:00:00:00:00 via RTM_SETLINK on the PF.
igb_ndo_set_vf_mac resets the IGB_VF_FLAG_PF_SET_MAC flag to 0,
so it's possible to reset the VF MAC back to the original value via
the VF netdev.
Note: Recent patches to libvirt allow for a workaround if the NIC
isn't capable of resetting the administrative MAC back to all 0, but
in theory the NIC should allow resetting the MAC in the first place.
Signed-off-by: Corinna Vinschen <vinschen@redhat.com> Tested-by: Aaron Brown <arron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Attributes that only implement .seq_ops are read-only, any write to
them should be rejected. But currently kernel would crash when
writing to such debugfs entries, e.g.
Another VCPU might try to modify the SCB while we are creating the
shadow SCB. In general this is no problem - unless the compiler decides
to not load values once, but e.g. twice.
For us, this is only relevant when checking/working with such values.
E.g. the prefix value, the mso, state of transactional execution and
addresses of satellite blocks.
E.g. if we blindly forward values (e.g. general purpose registers or
execution controls after masking), we don't care.
Leaving unpin_blocks() untouched for now, will handle it separately.
The worst thing right now that I can see would be a missed prefix
un/remap (mso, prefix, tx) or using wrong guest addresses. Nothing
critical, but let's try to avoid unpredictable behavior.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180116171526.12343-2-david@redhat.com> Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com> Acked-by: Cornelia Huck <cohuck@redhat.com> Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This patch prevents the thinkpad_acpi driver from warning about 2 event
codes returned for keyboard palm-detection. No behavioral changes,
other than suppressing the warning in the kernel log. The events are
still forwarded via acpi-netlink channels.
We could, optionally, decide to forward the event through a
input-switch on the tpacpi input device. However, so far no suitable
input-code exists, and no similar drivers report such events. Hence,
leave it an acpi event for now.
Note that the event-codes are named based on empirical studies. On the
ThinkPad X1 5th Gen the sensor can be found underneath the arrow key.
Cc: Matthew Thode <mthode@mthode.org> Signed-off-by: David Herrmann <dh.herrmann@gmail.com> Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If we receive the link status message from PF with link up before queues
are actually enabled, it will trigger a TX hang. This fixes the issue
by ignoring a link up message if the VF state is not yet in RUNNING
state.
Signed-off-by: Alan Brady <alan.brady@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When a host disables and enables a PF device, all the associated
VFs are removed and added back in. It also generates a PFR which in turn
resets all the connected VFs. This behaviour is different from that of
Linux guest on Linux host. Hence we end up in a situation where there's
a PFR and device removal at the same time. And watchdog doesn't have a
clue about this and schedules a reset_task. This patch adds code to send
signal to reset_task that the device is currently being removed.
Signed-off-by: Avinash Dayanand <avinash.dayanand@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
We get the "new_profile_index" value from the mouse device when we're
handling raw events. Smatch taints it as untrusted data and complains
that we need a bounds check. This seems like a reasonable warning
otherwise there is a small read beyond the end of the array.
Fixes: 0e70f97f257e ("HID: roccat: Add support for Kova[+] mouse") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Silvan Jegen <s.jegen@gmail.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The interrupt is requested before the device is powered on and
it's value in some cases cannot be reliable. It happens on some
devices that an interrupt is generated as soon as requested
before having the chance to disable the irq.
Set the irq flag as IRQ_NOAUTOEN before requesting it.
While testing with the ARM specific memset() macro removed, I ran into a
compiler warning that shows an old bug:
drivers/scsi/arm/fas216.c: In function 'fas216_rq_sns_done':
drivers/scsi/arm/fas216.c:2014:40: error: argument to 'sizeof' in 'memset' call is the same expression as the destination; did you mean to provide an explicit length? [-Werror=sizeof-pointer-memaccess]
It turns out that the definition of the scsi_cmd structure changed back
in linux-2.6.25, so now we clear only four bytes (sizeof(pointer))
instead of 96 (SCSI_SENSE_BUFFERSIZE). I did not check whether we
actually need to initialize the buffer here, but it's clear that if we
do it, we should use the correct size.
Fixes: de25deb18016 ("[SCSI] use dynamically allocated sense buffer") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When io_bits is set, GCing encrypted block may hit the following hungtask.
Since io_bits requires aligned block address, f2fs_submit_page_write may
return -EAGAIN if new_blkaddr does not satisify io_bits alignment. As a
result, the encrypted page will never be writtenback.
This patch makes move_data_block aware the EAGAIN error and cancel the
writeback.
Before rbio_orig_end_io() goes to free rbio, rbio may get merged with
more bios from other rbios and rbio->bio_list becomes non-empty,
in that case, these newly merged bios don't end properly.
Once unlock_stripe() is done, rbio->bio_list will not be updated any
more and we can call bio_endio() on all queued bios.
It should only happen in error-out cases, the normal path of recover
and full stripe write have already set RBIO_RMW_LOCKED_BIT to disable
merge before doing IO, so rbio_orig_end_io() called by them doesn't
have the above issue.
Reported-by: Jérôme Carretero <cJ-ko@zougloub.eu> Signed-off-by: Liu Bo <bo.li.liu@oracle.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This fixes a corner case that is caused by a race of dio write vs dio
read/write.
Here is how the race could happen.
Suppose that no extent map has been loaded into memory yet.
There is a file extent [0, 32K), two jobs are running concurrently
against it, t1 is doing dio write to [8K, 32K) and t2 is doing dio
read from [0, 4K) or [4K, 8K).
t1 goes ahead of t2 and splits em [0, 32K) to em [0K, 8K) and [8K 32K).
------------------------------------------------------
t1 t2
btrfs_get_blocks_direct() btrfs_get_blocks_direct()
-> btrfs_get_extent() -> btrfs_get_extent()
-> lookup_extent_mapping()
-> add_extent_mapping() -> lookup_extent_mapping()
# load [0, 32K)
-> btrfs_new_extent_direct()
-> btrfs_drop_extent_cache()
# split [0, 32K) and
# drop [8K, 32K)
-> add_extent_mapping()
# add [8K, 32K)
-> add_extent_mapping()
# handle -EEXIST when adding
# [0, 32K)
------------------------------------------------------
About how t2(dio read/write) runs into -EEXIST:
a) add_extent_mapping() gets -EEXIST for adding em [0, 32k),
b) search_extent_mapping() then returns [0, 8k) as the existing em,
even though start == existing->start, em is [0, 32k) so that
extent_map_end(em) > extent_map_end(existing), i.e. 32k > 8k,
c) then it goes thru merge_extent_mapping() which tries to add a [8k, 8k)
(with a length 0) and returns -EEXIST as [8k, 32k) is already in tree,
d) so btrfs_get_extent() ends up returning -EEXIST to dio read/write,
which is confusing applications.
Here I conclude all the possible situations,
1) start < existing->start
As we can see, it turns out that if start is within existing em (front
inclusive), then the existing em should be returned as is, otherwise,
we try our best to merge candidate em with sibling ems to form a
larger em (in order to reduce the total number of em).
Reported-by: David Vallender <david.vallender@landmark.co.uk> Signed-off-by: Liu Bo <bo.li.liu@oracle.com> Reviewed-by: Josef Bacik <jbacik@fb.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
It appears from the original commit [1] that there isn't any design
specific reason not to fail the mount instead of just warning. This
patch will change it to fail.
The raid6 corruption is that,
suppose that all disks can be read without problems and if the content
that was read out doesn't match its checksum, currently for raid6
btrfs at most retries twice,
- the 1st retry is to rebuild with all other stripes, it'll eventually
be a raid5 xor rebuild,
- if the 1st fails, the 2nd retry will deliberately fail parity p so
that it will do raid6 style rebuild,
however, the chances are that another non-parity stripe content also
has something corrupted, so that the above retries are not able to
return correct content.
We've fixed normal reads to rebuild raid6 correctly with more retries
in Patch "Btrfs: make raid6 rebuild retry more"[1], this is to fix
scrub to do the exactly same rebuild process.
When modifying a tree where the root is at BTRFS_MAX_LEVEL - 1 then
the level variable is going to be 7 (this is the max height of the
tree). On the other hand btrfs_cow_block is always called with
"level + 1" as an index into the nodes and slots arrays. This leads to
an out of bounds access. Admittdely this will be benign since an OOB
access of the nodes array will likely read the 0th element from the
slots array, which in this case is going to be 0 (since we start CoW at
the top of the tree). The OOB access into the slots array in turn will
read the 0th and 1st values of the locks array, which would both be 0
at the time. However, this benign behavior relies on the fact that the
path being passed hasn't been initialised, if it has already been used to
query a btree then it could potentially have populated the nodes/slots arrays.
Fix it by explicitly checking if we are at level 7 (the maximum allowed
index in nodes/slots arrays) and explicitly call the CoW routine with
NULL for parent's node/slot.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Fixes-coverity-id: 711515 Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Setting plug can merge adjacent IOs before dispatching IOs to the disk
driver.
Without plug, it'd not be a problem for single disk usecases, but for
multiple disks using raid profile, a large IO can be split to several
IOs of stripe length, and plug can be helpful to bring them together
for each disk so that we can save several disk access.
Moreover, fsync issues synchronous writes, so plug can really take
effect.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If a 'mainmenu' entry appeared in the Kconfig files, two things would
leak:
- The 'struct property' allocated for the default "Linux Kernel
Configuration" prompt.
- The string for the T_WORD/T_WORD_QUOTE prompt after the
T_MAINMENU token, allocated on the heap in zconf.l.
To fix it, introduce a new 'no_mainmenu_stmt' nonterminal that matches
if there's no 'mainmenu' and adds the default prompt. That means the
prompt only gets allocated once regardless of whether there's a
'mainmenu' statement or not, and managing it becomes simple.
Summary from Valgrind on 'menuconfig' (ARCH=x86) before the fix:
LEAK SUMMARY:
definitely lost: 344,568 bytes in 14,352 blocks
...
Summary after the fix:
LEAK SUMMARY:
definitely lost: 344,440 bytes in 14,350 blocks
...
According to all published information, the watchdog disable bit for SB800
compatible controllers is bit 1 of PM register 0x48, not bit 2. For the
most part that doesn't matter in practice, since the bit has to be cleared
to enable watchdog address decoding, which is the default setting, but it
still needs to be fixed.
Cc: Zoltán Böszörményi <zboszor@pr.hu> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@iguana.be> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Some hardware can operate in either "host" or "endpoint" mode, which means
there can be both a host bridge driver and an endpoint driver for the same
device. Those drivers share a lot of code, so sometimes they live in the
same source file.
The host bridge driver requires CONFIG_PCI=y because it enumerates PCI
devices below the bridge using the PCI core. The endpoint driver does not
require CONFIG_PCI=y because it runs in an embedded kernel on the other
side of the device, e.g., on an adapter card.
pci-dra7xx.c contains both host and endpoint drivers. If we select only
the endpoint driver (CONFIG_PCI=n and CONFIG_PCI_DRA7XX_EP=y), the unneeded
host driver is still compiled. It references pci_irqd_intx_xlate(), which
is not present when CONFIG_PCI=n, which causes this error:
drivers/pci/dwc/pci-dra7xx.c:229:11: error: 'pci_irqd_intx_xlate' undeclared here (not in a function)
Add a dummy pci_irqd_intx_xlate() for the CONFIG_PCI=n case.
Make doesn't expand shell style "vmlinuz.{32,ecoff,bin,srec}" to the 4
separate files, so none of these files get cleaned up by make clean.
List the files separately instead.
Fixes: ec3352925b74 ("MIPS: Remove all generated vmlinuz* files on "make clean"") Signed-off-by: James Hogan <jhogan@kernel.org> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/18491/ Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Since commit 57e62324e469 ("NFS: Store the legacy idmapper result in the
keyring") nfs_idmap_cache_timeout changed units from jiffies to seconds.
Unfortunately sysctl interface was not updated accordingly.
As a effect updating /proc/sys/fs/nfs/idmap_cache_timeout with some
value will incorrectly multiply this value by HZ.
Also reading /proc/sys/fs/nfs/idmap_cache_timeout will show real value
divided by HZ.
Fixes: 57e62324e469 ("NFS: Store the legacy idmapper result in the keyring") Signed-off-by: Jan Chochol <jan@chochol.info> Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
polling the completion queue directly does not interfere
with the existing polling logic, hence drop the requirement.
Be aware that running ib_process_cq_direct with non IB_POLL_DIRECT
CQ may trigger concurrent CQ processing.
This can be used for polling mode ULPs.
Cc: Bart Van Assche <bart.vanassche@wdc.com> Reported-by: Steve Wise <swise@opengridcomputing.com> Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
[maxg: added wcs array argument to __ib_process_cq] Signed-off-by: Max Gurtovoy <maxg@mellanox.com> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
On Meson8b the only valid input clock is MPLL2. The bootloader
configures that to run at 500002394Hz which cannot be divided evenly
down to 125MHz using the m250_div clock. Currently the common clock
framework chooses a m250_div of 2 - with the internal fixed
"divide by 10" this results in a RGMII TX clock of 125001197Hz (120Hz
above the requested 125MHz).
Letting the common clock framework propagate the rate changes up to the
parent of m250_mux allows us to get the best possible clock rate. With
this patch the common clock framework calculates a rate of
very-close-to-250MHz (249999701Hz to be exact) for the MPLL2 clock
(which is the mux input). Dividing that by 2 (which is an internal,
fixed divider for the RGMII TX clock) gives us an RGMII TX clock of
124999850Hz (which is only 150Hz off the requested 125MHz, compared to
1197Hz based on the MPLL2 rate set by u-boot and the Amlogic GPL kernel
sources).
SoCs from the Meson GX series are not affected by this change because
the input clock is FCLK_DIV2 whose rate cannot be changed (which is fine
since it's running at 1GHz, so it's already a multiple of 250MHz and
125MHz).
Fixes: 566e8251625304 ("net: stmmac: add a glue driver for the Amlogic Meson 8b / GXBB DWMAC") Suggested-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Reviewed-by: Jerome Brunet <jbrunet@baylibre.com> Tested-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Meson8b only supports MPLL2 as clock input. The rate of the MPLL2 clock
set by Odroid-C1's u-boot is close to (but not exactly) 500MHz. The
exact rate is 500002394Hz, which is calculated in
drivers/clk/meson/clk-mpll.c using the following formula:
DIV_ROUND_UP_ULL((u64)parent_rate * SDM_DEN, (SDM_DEN * n2) + sdm)
Odroid-C1's u-boot configures MPLL2 with the following values:
- SDM_DEN = 16384
- SDM = 1638
- N2 = 5
The 250MHz clock (m250_div) inside dwmac-meson8b driver is derived from
the MPLL2 clock. Due to MPLL2 running slightly faster than 500MHz the
common clock framework chooses a divider which is too big to generate
the 250MHz clock (a divider of 2 would be needed, but this is rounded up
to a divider of 3). This breaks the RTL8211F RGMII PHY on Odroid-C1
because it requires a (close to) 125MHz RGMII TX clock (on Gbit speeds,
the IP block internally divides that down to 25MHz on 100Mbit/s
connections and 2.5MHz on 10Mbit/s connections - we don't need any
special configuration for that).
Round the divider to the closest value to prevent this issue on Meson8b.
This means we'll now end up with a clock rate for the RGMII TX clock of
125001197Hz (= 125MHz plus 1197Hz), which is close-enough to 125MHz.
This has no effect on the Meson GX SoCs since there fclk_div2 is used as
input clock, which has a rate of 1000MHz (and thus is divisible cleanly
to 250MHz and 125MHz).
Fixes: 566e8251625304 ("net: stmmac: add a glue driver for the Amlogic Meson 8b / GXBB DWMAC") Reported-by: Emiliano Ingrassia <ingrassia@epigenesys.com> Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Reviewed-by: Jerome Brunet <jbrunet@baylibre.com> Tested-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
fs/ubifs/tnc.c: In function ‘search_dh_cookie’:
fs/ubifs/tnc.c:1893: warning: ‘err’ is used uninitialized in this function
Indeed, err is always used uninitialized.
According to an original review comment from Hyunchul, acknowledged by
Richard, err should be initialized to -ENOENT to avoid the first call to
tnc_next(). But we can achieve the same by reordering the code.
blk-mq will rerun queue via RESTART or dispatch wake after one request
is completed, so not necessary to wait random time for requeuing, we
should trust blk-mq to do it.
More importantly, we need to return BLK_STS_RESOURCE to blk-mq so that
dequeuing from the I/O scheduler can be stopped, this results in
improved I/O merging.
Signed-off-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Fixes:
1. The use of "exceeds" when the opposite of exceeds, falls below,
was meant.
2. Properly speaking, a table can not exceed a threshold.
It emphasizes the important point, which is that it is the userspace
daemon's responsibility to check for low free space when a device
is resumed, since it won't get a special event indicating low free
space in that situation.
after commit a1ddcbe93010 ("iommu/vt-d: Pass dmar_domain directly into
iommu_flush_iotlb_psi", 2015-08-12), we have domain pointer as parameter
to iommu_flush_iotlb_psi(), so no need to fetch it from cache again.
More importantly, a NULL reference pointer bug is reported on RHEL7 (and
it can be reproduced on some old upstream kernels too, e.g., v4.13) by
unplugging an 40g nic from a VM (hard to test unplug on real host, but
it should be the same):
This patch fixes that problem if applied to v4.13 kernel.
The bug does not exist on latest upstream kernel since it's fixed as a
side effect of commit 13cf01744608 ("iommu/vt-d: Make use of iova
deferred flushing", 2017-08-15). But IMHO it's still good to have this
patch upstream.
CC: Alex Williamson <alex.williamson@redhat.com> Signed-off-by: Peter Xu <peterx@redhat.com> Fixes: a1ddcbe93010 ("iommu/vt-d: Pass dmar_domain directly into iommu_flush_iotlb_psi") Reviewed-by: Alex Williamson <alex.williamson@redhat.com> Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The die() oops path contains a serializing lock to prevent oops
messages from being interleaved. In the case of a system reset
initiated oops (e.g., qemu nmi command), __die was being called
which lacks that synchronisation and oops reports could be
interleaved across CPUs.
A recent patch 4388c9b3a6ee7 ("powerpc: Do not send system reset
request through the oops path") changed this to __die to avoid
the debugger() call, but there is no real harm to calling it twice
if the first time fell through. So go back to using die() here.
This was observed to fix the problem.
Fixes: 4388c9b3a6ee7 ("powerpc: Do not send system reset request through the oops path") Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Reviewed-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Removing the early device registration hook overlooked the fact that
it only ran conditionally on a compatible device being present in the
DT. With exynos_iommu_init() now running as an unconditional initcall,
problems arise on non-Exynos systems when other IOMMU drivers find
themselves unable to install their ops on the platform bus, or at worst
the Exynos ops get called with someone else's domain and all hell breaks
loose.
The global ops/cache setup could probably all now be triggered from the
first IOMMU probe, as with dma_dev assigment, but for the time being the
simplest fix is to resurrect the logic from commit a7b67cd5d9af
("iommu/exynos: Play nice in multi-platform builds") to explicitly check
the DT for the presence of an Exynos IOMMU before trying anything.
In x86 architecture dependend part function get_cpuid_str() mallocs a
128 byte buffer, but does not check if the memory allocation succeeded
or not.
When the memory allocation fails, function __get_cpuid() is called with
first parameter being a NULL pointer. However this function references
its first parameter and operates on a NULL pointer which might cause
core dumps.
Signed-off-by: Thomas Richter <tmricht@linux.vnet.ibm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Hendrik Brueckner <brueckner@linux.vnet.ibm.com> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Link: http://lkml.kernel.org/r/20180117131611.34319-1-tmricht@linux.vnet.ibm.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If a field is a dynamic string, get_field_str() returned just the
offset/size value and not the string. Have it parse the offset/size
correctly to return the actual string. Otherwise filtering fails when
trying to filter fields that are dynamic strings.
Reported-by: Gopanapalli Pradeep <prap_hai@yahoo.com> Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Acked-by: Namhyung Kim <namhyung@kernel.org> Cc: Andrew Morton <akpm@linux-foundation.org> Link: http://lkml.kernel.org/r/20180112004823.146333275@goodmis.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When setting the "dwarf" unwinder for a specific event and not
specifying the max-stack, the attr.sample_max_stack ended up using an
uninitialized callchain_param.max_stack, fix it by using designated
initializers for that callchain_param variable, zeroing all non
explicitely initialized struct members.
Here is what happened:
# perf trace -vv --no-syscalls --max-stack 4 -e probe_libc:inet_pton/call-graph=dwarf/ ping -6 -c 1 ::1
callchain: type DWARF
callchain: stack dump size 8192
perf_event_attr:
type 2
size 112
config 0x730
{ sample_period, sample_freq } 1
sample_type IP|TID|TIME|ADDR|CALLCHAIN|CPU|PERIOD|RAW|REGS_USER|STACK_USER|DATA_SRC
exclude_callchain_user 1
{ wakeup_events, wakeup_watermark } 1
sample_regs_user 0xff0fff
sample_stack_user 8192
sample_max_stack 50656
sys_perf_event_open failed, error -75
Value too large for defined data type
# perf trace -vv --no-syscalls --max-stack 4 -e probe_libc:inet_pton/call-graph=dwarf/ ping -6 -c 1 ::1
callchain: type DWARF
callchain: stack dump size 8192
perf_event_attr:
type 2
size 112
config 0x730
sample_type IP|TID|TIME|ADDR|CALLCHAIN|CPU|PERIOD|RAW|REGS_USER|STACK_USER|DATA_SRC
exclude_callchain_user 1
sample_regs_user 0xff0fff
sample_stack_user 8192
sample_max_stack 30448
sys_perf_event_open failed, error -75
Value too large for defined data type
#
Now the attr.sample_max_stack is set to zero and the above works as
expected:
# perf trace --no-syscalls --max-stack 4 -e probe_libc:inet_pton/call-graph=dwarf/ ping -6 -c 1 ::1
PING ::1(::1) 56 data bytes
64 bytes from ::1: icmp_seq=1 ttl=64 time=0.072 ms
When processing %pX in pretty_print(), simplify the logic slightly by
incrementing the ptr to the format string if isalnum(ptr[1]) is true.
This follows the logic a bit more closely to what is in the kernel.
Also, this fixes a small bug where %pF was not giving the offset of the
function.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Acked-by: Namhyung Kim <namhyung@kernel.org> Cc: Andrew Morton <akpm@linux-foundation.org> Link: http://lkml.kernel.org/r/20180112004822.260262257@goodmis.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When setting up DWARF callchains on specific events, without using
'record' or 'trace' --call-graph, but instead doing it like:
perf trace -e cycles/call-graph=dwarf/
The unwind__prepare_access() call in thread__insert_map() when we
process PERF_RECORD_MMAP(2) metadata events were not being performed,
precluding us from using per-event DWARF callchains, handling them just
when we asked for all events to be DWARF, using "--call-graph dwarf".
We do it in the PERF_RECORD_MMAP because we have to look at one of the
executable maps to figure out the executable type (64-bit, 32-bit) of
the DSO laid out in that mmap. Also to look at the architecture where
the perf.data file was recorded.
All this probably should be deferred to when we process a sample for
some thread that has callchains, so that we do this processing only for
the threads with samples, not for all of them.
For now, fix using DWARF on specific events.
Before:
# perf trace --no-syscalls -e probe_libc:inet_pton/call-graph=dwarf/ ping -6 -c 1 ::1
PING ::1(::1) 56 data bytes
64 bytes from ::1: icmp_seq=1 ttl=64 time=0.048 ms
--- ::1 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.048/0.048/0.048/0.000 ms
0.000 probe_libc:inet_pton:(7fe9597bb350))
Problem processing probe_libc:inet_pton callchain, skipping...
#
After:
# perf trace --no-syscalls -e probe_libc:inet_pton/call-graph=dwarf/ ping -6 -c 1 ::1
PING ::1(::1) 56 data bytes
64 bytes from ::1: icmp_seq=1 ttl=64 time=0.060 ms
If the application invalidates the MR before the FMR WR, HW parses the
consumer key portion of the stag and returns an invalid stag key
Asynchronous Event (AE) that tears down the QP.
Fix this by zeroing-out the consumer key portion of the allocated stag
returned to application for FMR.
input_mt_init_slots() resets the ABS_X/Y fuzz to 0 and expects the driver
to call input_mt_report_pointer_emulation(). That is based on the MT
position bits which are already defuzzed - hence a fuzz of 0.
In the case of synaptics semi-mt devices, we report the ABS_X/Y axes
manually. This results in the MT position being defuzzed but the
single-touch emulation missing that defuzzing.
Work around this by re-initializing the ABS_X/Y axes after the MT axis to
get the same fuzz value back.
When Synaptics protocol is disabled, we still need to try and detect the
hardware, so we can switch to SMBus device if SMbus is detected, or we know
that it is Synaptics device and reset it properly for the bare PS/2
protocol.
The Marvell 9128 is the original device generating bug 42679, from which
many other Marvell DMA alias quirks have been sourced, but we didn't have
positive confirmation of the fix on 9128 until now.
Fix to pick text symbols for multiple kprobe testcase.
kallsyms shows text symbols with " t " or " T " but
current testcase picks all symbols including "t",
so it picks data symbols if it includes 't' (e.g. "str").
This fixes it to find symbol lines with " t " or " T "
(including spaces).
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org> Reported-by: Russell King <linux@armlinux.org.uk> Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Chuck Lever [Fri, 15 Dec 2017 01:56:09 +0000 (20:56 -0500)]
xprtrdma: Fix backchannel allocation of extra rpcrdma_reps
BugLink: http://bugs.launchpad.net/bugs/1774063
The backchannel code uses rpcrdma_recv_buffer_put to add new reps
to the free rep list. This also decrements rb_recv_count, which
spoofs the receive overrun logic in rpcrdma_buffer_get_rep.
Commit 9b06688bc3b9 ("xprtrdma: Fix additional uses of
spin_lock_irqsave(rb_lock)") replaced the original open-coded
list_add with a call to rpcrdma_recv_buffer_put(), but then a year
later, commit 05c974669ece ("xprtrdma: Fix receive buffer
accounting") added rep accounting to rpcrdma_recv_buffer_put.
It was an oversight to let the backchannel continue to use this
function.
The fix this, let's combine the "add to free list" logic with
rpcrdma_create_rep.
Also, do not allocate RPCRDMA_MAX_BC_REQUESTS rpcrdma_reps in
rpcrdma_buffer_create and then allocate additional rpcrdma_reps in
rpcrdma_bc_setup_reps. Allocating the extra reps during backchannel
set-up is sufficient.
Fixes: 05c974669ece ("xprtrdma: Fix receive buffer accounting") Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
(cherry picked from commit d698c4a02ee02053bbebe051322ff427a2dad56a) Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
On some Dell XPS models WMI events of type 0x0000 reporting a keycode of
0xe00c get reported when the brightness of the LCD panel changes.
This leads to us reporting false-positive kbd_led change events to
userspace which in turn leads to the kbd backlight OSD showing when it
should not.
We already read the current keyboard backlight brightness value when
reporting events because the led_classdev_notify_brightness_hw_changed
API requires this. Compare this value to the last known value and filter
out duplicate events, fixing this.
Note the fixed issue is esp. a problem on XPS models with an ambient light
sensor and automatic brightness adjustments turned on, this causes the kbd
backlight OSD to show all the time there.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1514969 Fixes: 9c656b0799 ("platform/x86: dell-*: Call new led hw_changed API ...") Acked-by: Pali Rohár <pali.rohar@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
commit a03825bbd0c3 ("KVM: s390: use kvm->created_vcpus") introduced
kvm->created_vcpus to avoid races with the existing kvm->online_vcpus
scheme. One place was "forgotten" and one new place was "added".
Let's fix those.
Reported-by: Halil Pasic <pasic@linux.vnet.ibm.com> Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Reviewed-by: Halil Pasic <pasic@linux.vnet.ibm.com> Reviewed-by: Cornelia Huck <cohuck@redhat.com> Reviewed-by: David Hildenbrand <david@redhat.com> Fixes: 4e0b1ab72b8a ("KVM: s390: gs support for kvm guests") Fixes: a03825bbd0c3 ("KVM: s390: use kvm->created_vcpus") Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
So far only CLOCK_MONOTONIC and CLOCK_REALTIME were taken into account as
well as HRTIMER_MODE_ABS/REL in the hrtimer_init tracepoint. The query for
detecting the ABS or REL timer modes is not valid anymore, it got broken
by the introduction of HRTIMER_MODE_PINNED.
HRTIMER_MODE_PINNED is not evaluated in the hrtimer_init() call, but for the
sake of completeness print all given modes.
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de> Cc: Christoph Hellwig <hch@lst.de> Cc: John Stultz <john.stultz@linaro.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: keescook@chromium.org Link: http://lkml.kernel.org/r/20171221104205.7269-9-anna-maria@linutronix.de Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
ipv6_defrag pulls network headers before fragment header. In case of
an error, the netfilter layer is currently dropping these packets.
This results in failure of some IPv6 standards tests which passed on
older kernels due to the netfilter framework using cloning.
The test case run here is a check for ICMPv6 error message replies
when some invalid IPv6 fragments are sent. This specific test case is
listed in https://www.ipv6ready.org/docs/Core_Conformance_Latest.pdf
in the Extension Header Processing Order section.
A packet with unrecognized option Type 11 is sent and the test expects
an ICMP error in line with RFC2460 section 4.2 -
11 - discard the packet and, only if the packet's Destination
Address was not a multicast address, send an ICMP Parameter
Problem, Code 2, message to the packet's Source Address,
pointing to the unrecognized Option Type.
Since netfilter layer now drops all invalid IPv6 frag packets, we no
longer see the ICMP error message and fail the test case.
To fix this, save the transport header. If defrag is unable to process
the packet due to RFC2460, restore the transport header and allow packet
to be processed by stack. There is no change for other packet
processing paths.
Tested by confirming that stack sends an ICMP error when it receives
these packets. Also tested that fragmented ICMP pings succeed.
v1->v2: Instead of cloning always, save the transport_header and
restore it in case of this specific error. Update the title and
commit message accordingly.
This adds a register identifier for use with the one_reg interface
to allow the decrementer expiry time to be read and written by
userspace. The decrementer expiry time is in guest timebase units
and is equal to the sum of the decrementer and the guest timebase.
(The expiry time is used rather than the decrementer value itself
because the expiry time is not constantly changing, though the
decrementer value is, while the guest vcpu is not running.)
Without this, a guest vcpu migrated to a new host will see its
decrementer set to some random value. On POWER8 and earlier, the
decrementer is 32 bits wide and counts down at 512MHz, so the
guest vcpu will potentially see no decrementer interrupts for up
to about 4 seconds, which will lead to a stall. With POWER9, the
decrementer is now 56 bits side, so the stall can be much longer
(up to 2.23 years) and more noticeable.
To help work around the problem in cases where userspace has not been
updated to migrate the decrementer expiry time, we now set the
default decrementer expiry at vcpu creation time to the current time
rather than the maximum possible value. This should mean an
immediate decrementer interrupt when a migrated vcpu starts
running. In cases where the decrementer is 32 bits wide and more
than 4 seconds elapse between the creation of the vcpu and when it
first runs, the decrementer would have wrapped around to positive
values and there may still be a stall - but this is no worse than
the current situation. In the large-decrementer case, we are sure
to get an immediate decrementer interrupt (assuming the time from
vcpu creation to first run is less than 2.23 years) and we thus
avoid a very long stall.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
iWARP does not use rdma_ah_attr_type, and for this reason we do not have a
RDMA_AH_ATTR_TYPE_IWARP. rdma_ah_find_type should not even be called on iwarp
ports and for clarity it shouldn't have a special test for iWarp.
This changes the result from RDMA_AH_ATTR_TYPE_ROCE to RDMA_AH_ATTR_TYPE_IB
when wrongly called on an iWarp port.
Fixes: 44c58487d51a ("IB/core: Define 'ib' and 'roce' rdma_ah_attr types") Signed-off-by: Parav Pandit <parav@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This ioctl is obsolete (it was used by Xenner as far as I know) but
still let's not break it gratuitously... Its handler is copying
directly into struct kvm. Go through a bounce buffer instead, with
the added benefit that we can actually do something useful with the
flags argument---the previous code was exiting with -EINVAL but still
doing the copy.
This technically is a userspace ABI breakage, but since no one should be
using the ioctl, it's a good occasion to see if someone actually
complains.
The loop timeout doesn't work because it's a post op and ends with "tmo"
set to -1. I changed it from a post-op to a pre-op and I changed the
initial the starting value from 5 to 6 so we still iterate 5 times. I
left the other as it was because it's a large number.
Fixes: b3c70c9ea62a ("ASoC: Alchemy AC97C/I2SC audio support") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The commit ffcd28d88e4f ("ALSA: hda - Select INPUT for Realtek
HD-audio codec") introduced the reverse-selection of CONFIG_INPUT for
Realtek codec in order to avoid the mess with dependency between
built-in and modules. Later on, we obtained IS_REACHABLE() macro
exactly for this kind of problems, and now we can remove th INPUT
selection in Kconfig and put IS_REACHABLE(INPUT) to the appropriate
places in the code, so that the driver doesn't need to select other
subsystem forcibly.
Fixes: ffcd28d88e4f ("ALSA: hda - Select INPUT for Realtek HD-audio codec") Reported-by: Randy Dunlap <rdunlap@infradead.org> Acked-by: Randy Dunlap <rdunlap@infradead.org> # and build-tested Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
acpi_lpss_create_device() skips handling LPSS devices which do not have
a mmio resources in their resource list (typically these devices are
disabled by the firmware). But since the LPSS code does not bind to the
device, acpi_bus_attach() ends up still creating a platform device for
it and the regular platform_driver for the ACPI HID still tries to bind
to it.
This happens e.g. on some boards which do not use the pwm-controller
and have an empty or invalid resource-table for it. Currently this causes
these error messages to get logged:
[ 3.281966] pwm-lpss 80862288:00: invalid resource
[ 3.287098] pwm-lpss: probe of 80862288:00 failed with error -22
This commit stops the undesirable creation of a platform_device for
disabled LPSS devices by setting pnp.type.platform_id to 0. Note that
acpi_scan_attach_handler() also sets pnp.type.platform_id to 0 when there
is a matching handler for the device and that handler has no attach
callback, so we simply behave as a handler without an attach function
in this case.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
There are 2 comments in the NFSv4 code which suggest that
SIGLOST should possibly be sent to a process. In these
cases a lock has been lost.
The current practice is to set NFS_LOCK_LOST so that
read/write returns EIO when a lock is lost.
So change these comments to code when sets NFS_LOCK_LOST.
One case is when lock recovery after apparent server restart
fails with NFS4ERR_DENIED, NFS4ERR_RECLAIM_BAD, or
NFS4ERRO_RECLAIM_CONFLICT. The other case is when a lock
attempt as part of lease recovery fails with NFS4ERR_DENIED.
In an ideal world, these should not happen. However I have
a packet trace showing an NFSv4.1 session getting
NFS4ERR_BADSESSION after an extended network parition. The
NFSv4.1 client treats this like server reboot until/unless
it get NFS4ERR_NO_GRACE, in which case it switches over to
"nograce" recovery mode. In this network trace, the client
attempts to recover a lock and the server (incorrectly)
reports NFS4ERR_DENIED rather than NFS4ERR_NO_GRACE. This
leads to the ineffective comment and the client then
continues to write using the OPEN stateid.
Zhang Rui reported that a Surface Pro 4 will fail to boot with
lapic=notscdeadline. Part of the problem is that that machine doesn't have
a PIT.
If, for some reason, the TSC init has to fall back to TSC calibration, it
relies on the PIT to be present.
Allow TSC calibration to reliably fall back to HPET.
The below results in an accurate TSC measurement when forced on a IVB:
tsc: Unable to calibrate against PIT
tsc: No reference (HPET/PMTIMER) available
tsc: Unable to calibrate against PIT
tsc: using HPET reference calibration
tsc: Detected 2792.451 MHz processor
At least some JMicron controllers issue buggy oversized DMA reads when
fetching context descriptors, always fetching 0x20 bytes at once for
descriptors which are only 0x10 bytes long. This is often harmless, but
can cause page faults on modern systems with IOMMUs:
DMAR: [DMA Read] Request device [05:00.0] fault addr fff56000 [fault reason 06] PTE Read access is not set
firewire_ohci 0000:05:00.0: DMA context IT0 has stopped, error code: evt_descriptor_read
This works around the problem by always leaving 0x10 padding bytes at
the end of descriptor buffer pages, which should be harmless to do
unconditionally for controllers in case others have the same behavior.
Signed-off-by: Hector Martin <marcan@marcan.st> Reviewed-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Without pm_runtime_{get,put}_sync calls in place, reading
vbus status via /sys causes the following error:
Unhandled fault: external abort on non-linefetch (0x1028) at 0xfa0ab060
pgd = b333e822
[fa0ab060] *pgd=48011452(bad)
[<c05261b0>] (musb_default_readb) from [<c0525bd0>] (musb_vbus_show+0x58/0xe4)
[<c0525bd0>] (musb_vbus_show) from [<c04c0148>] (dev_attr_show+0x20/0x44)
[<c04c0148>] (dev_attr_show) from [<c0259f74>] (sysfs_kf_seq_show+0x80/0xdc)
[<c0259f74>] (sysfs_kf_seq_show) from [<c0210bac>] (seq_read+0x250/0x448)
[<c0210bac>] (seq_read) from [<c01edb40>] (__vfs_read+0x1c/0x118)
[<c01edb40>] (__vfs_read) from [<c01edccc>] (vfs_read+0x90/0x144)
[<c01edccc>] (vfs_read) from [<c01ee1d0>] (SyS_read+0x3c/0x74)
[<c01ee1d0>] (SyS_read) from [<c0106fe0>] (ret_fast_syscall+0x0/0x54)
Solution was suggested by Tony Lindgren <tony@atomide.com>.
Signed-off-by: Merlijn Wajer <merlijn@wizzup.org> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Bin Liu <b-liu@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
On dm3730 there are enumeration problems after resume.
Investigation led to the cause that the MUSB_POWER_SOFTCONN
bit is not set. If it was set before suspend (because it
was enabled via musb_pullup()), it is set in
musb_restore_context() so the pullup is enabled. But then
musb_start() is called which overwrites MUSB_POWER and
therefore disables MUSB_POWER_SOFTCONN, so no pullup is
enabled and the device is not enumerated.
So let's do a subset of what musb_start() does
in the same way as musb_suspend() does it. Platform-specific
stuff it still called as there might be some phy-related stuff
which needs to be enabled.
Also interrupts are enabled, as it was the original idea
of calling musb_start() in musb_resume() according to
Commit 6fc6f4b87cb3 ("usb: musb: Disable interrupts on suspend,
enable them on resume")
Signed-off-by: Andreas Kemnade <andreas@kemnade.info> Tested-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Bin Liu <b-liu@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Currently we see sporadic timeouts during CDCLK changing both on BXT and
GLK as reported by the Bugzilla: ticket. It's easy to reproduce this by
changing the frequency in a tight loop after blanking the display. The
upper bound for the completion time is 800us based on my tests, so
increase it from the current 500us to 2ms; with that I couldn't trigger
the problem either on BXT or GLK.
Note that timeouts happened during both the change notification and the
voltage level setting PCODE request. (For the latter one BSpec doesn't
require us to wait for completion before further HW programming.)
This issue is similar to
commit 2c7d0602c815 ("drm/i915/gen9: Fix PCODE polling during CDCLK
change notification")
but there the PCODE request does complete (as shown by the mbox
busy flag), only the reply we get from PCODE indicates a failure.
So there we keep resending the request until a success reply, here we
just have to increase the timeout for the one PCODE request we send.
Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: <stable@vger.kernel.org> # v4.4+ Acked-by: Chris Wilson <chris@chris-wilson.co.uk> (v1)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=103326 Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Imre Deak <imre.deak@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180130142939.17983-1-imre.deak@intel.com
(cherry picked from commit e76019a81921e87a4d9e7b3d86102bc708a6c227) Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
(Rebased for v4.14 stable tree due to upstream cdclk_state and pcu_lock change) Signed-off-by: Imre Deak <imre.deak@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
LSPCON adapters in low-power state may ignore the first I2C write during
TMDS output buffer enabling, resulting in a blank screen even with an
otherwise enabled pipe. Fix this by reading back and validating the
written value a few times.
The problem was noticed on GLK machines with an onboard LSPCON adapter
after entering/exiting DC5 power state. Doing an I2C read of the adapter
ID as the first transaction - instead of the I2C write to enable the
TMDS buffers - returns the correct value. Based on this we assume that
the transaction itself is sent properly, it's only the adapter that is
not ready for some reason to accept this first write after waking from
low-power state. In my case the second I2C write attempt always
succeeded.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105854 Cc: Clinton Taylor <clinton.a.taylor@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: stable@vger.kernel.org Signed-off-by: Imre Deak <imre.deak@intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180416155309.11100-1-imre.deak@intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Along the eb_lookup_vmas() error path, the return value from
kmem_cache_alloc() was freed using kfree(). Fix it to use the proper
kmem_cache_free() instead.
Fixes: d1b48c1e7184 ("drm/i915: Replace execbuf vma ht with an idr") Signed-off-by: Xidong Wang <wangxidong_97@163.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Cc: <stable@vger.kernel.org> # v4.14+ Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Link: https://patchwork.freedesktop.org/patch/msgid/20180404093824.9313-1-chris@chris-wilson.co.uk
(cherry picked from commit 6be1187dbffa0027ea379c53f7ca0c782515c610) Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>