Gayatri Kammela [Tue, 31 Oct 2017 01:20:29 +0000 (18:20 -0700)]
x86/cpufeatures: Enable new SSE/AVX/AVX512 CPU features
Add a few new SSE/AVX/AVX512 instruction groups/features for enumeration
in /proc/cpuinfo: AVX512_VBMI2, GFNI, VAES, VPCLMULQDQ, AVX512_VNNI,
AVX512_BITALG.
Detailed information of CPUID bits for these features can be found
in the Intel Architecture Instruction Set Extensions and Future Features
Programming Interface document (refer to Table 1-1. and Table 1-2.).
A copy of this document is available at
https://bugzilla.kernel.org/show_bug.cgi?id=197239
Thomas Gleixner [Wed, 18 Oct 2017 17:39:35 +0000 (19:39 +0200)]
x86/cpuid: Prevent out of bound access in do_clear_cpu_cap()
do_clear_cpu_cap() allocates a bitmap to keep track of disabled feature
dependencies. That bitmap is sized NCAPINTS * BITS_PER_INIT. The possible
'features' which can be handed in are larger than this, because after the
capabilities the bug 'feature' bits occupy another 32bit. Not really
obvious...
So clearing any of the misfeature bits, as 32bit does for the F00F bug,
accesses that bitmap out of bounds thereby corrupting the stack.
Size the bitmap proper and add a sanity check to catch accidental out of
bound access.
Fixes: 0b00de857a64 ("x86/cpuid: Add generic table for CPUID dependencies") Reported-by: kernel test robot <xiaolong.ye@intel.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Andi Kleen <ak@linux.intel.com> Cc: Borislav Petkov <bp@alien8.de> Link: https://lkml.kernel.org/r/20171018022023.GA12058@yexl-desktop
Andi Kleen [Fri, 13 Oct 2017 21:56:45 +0000 (14:56 -0700)]
x86/fpu: Remove the explicit clearing of XSAVE dependent features
Clearing a CPU feature with setup_clear_cpu_cap() clears all features
which depend on it. Expressing feature dependencies in one place is
easier to maintain than keeping functions like
fpu__xstate_clear_all_cpu_caps() up to date.
The features which depend on XSAVE have their dependency expressed in the
dependency table, so its sufficient to clear X86_FEATURE_XSAVE.
Remove the explicit clearing of XSAVE dependent features.
Andi Kleen [Fri, 13 Oct 2017 21:56:44 +0000 (14:56 -0700)]
x86/fpu: Make XSAVE check the base CPUID features before enabling
Before enabling XSAVE, not only check the XSAVE specific CPUID bits,
but also the base CPUID features of the respective XSAVE feature.
This allows to disable individual XSAVE states using the existing
clearcpuid= option, which can be useful for performance testing
and debugging, and also in general avoids inconsistencies.
Andi Kleen [Fri, 13 Oct 2017 21:56:43 +0000 (14:56 -0700)]
x86/fpu: Parse clearcpuid= as early XSAVE argument
With a followon patch we want to make clearcpuid affect the XSAVE
configuration. But xsave is currently initialized before arguments
are parsed. Move the clearcpuid= parsing into the special
early xsave argument parsing code.
Since clearcpuid= contains a = we need to keep the old __setup
around as a dummy, otherwise it would end up as a environment
variable in init's environment.
Andi Kleen [Fri, 13 Oct 2017 21:56:42 +0000 (14:56 -0700)]
x86/cpuid: Add generic table for CPUID dependencies
Some CPUID features depend on other features. Currently it's
possible to to clear dependent features, but not clear the base features,
which can cause various interesting problems.
This patch implements a generic table to describe dependencies
between CPUID features, to be used by all code that clears
CPUID.
Some subsystems (like XSAVE) had an own implementation of this,
but it's better to do it all in a single place for everyone.
Then clear_cpu_cap and setup_clear_cpu_cap always look up
this table and clear all dependencies too.
This is intended to be a practical table: only for features
that make sense to clear. If someone for example clears FPU,
or other features that are essentially part of the required
base feature set, not much is going to work. Handling
that is right now out of scope. We're only handling
features which can be usefully cleared.
Signed-off-by: Andi Kleen <ak@linux.intel.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Cc: Jonathan McDowell <noodles@earth.li> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/20171013215645.23166-3-andi@firstfloor.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
x86/fpu/debug: Remove unused 'x86_fpu_state' and 'x86_fpu_deactivate_state' tracepoints
Commit:
d1898b733619 ("x86/fpu: Add tracepoints to dump FPU state at key points")
... added the 'x86_fpu_state' and 'x86_fpu_deactivate_state' trace points,
but never used them. Today they are still not used. As they take up
and waste memory, remove them.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/20171012180619.670b68b6@gandalf.local.home Signed-off-by: Ingo Molnar <mingo@kernel.org>
Linus Torvalds [Fri, 13 Oct 2017 00:37:23 +0000 (17:37 -0700)]
Merge tag 'devprop-4.14-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull device properties framework fixes from Rafael Wysocki:
"These fix an issue related to device removal introduced during the 4.9
cycle and fix up new functionality added recently.
Specifics:
- Fix a device properties management issue, introduced during the 4.9
cycle, that causes device properties associated with a parent
device to go away on a removal of its child in some cases (Jarkko
Nikula).
- Fix inconsistencies in error codes returned by a new function
helper in the device properties framework depending on the
underlying low-level firmware interface, DT or ACPI, by making the
meaning of error codes returned in the ACPI case agree with the
meaning of DT error codes in analogous situations (Sakari Ailus)"
* tag 'devprop-4.14-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: properties: Fix __acpi_node_get_property_reference() return codes
ACPI: properties: Align return codes of __acpi_node_get_property_reference()
device property: Track owner device of device property
Linus Torvalds [Thu, 12 Oct 2017 21:51:13 +0000 (14:51 -0700)]
Merge tag 'xfs-4.14-fixes-5' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull xfs fixes from Darrick Wong:
- Fix a stale kernel memory exposure when logging inodes.
- Fix some build problems with CONFIG_XFS_RT=n
- Don't change inode mode if the acl write fails, leaving the file
totally inaccessible.
- Fix a dangling pointer problem when removing an attr fork under
memory pressure.
- Don't crash while trying to invalidate a null buffer associated with
a corrupt metadata pointer.
* tag 'xfs-4.14-fixes-5' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: handle error if xfs_btree_get_bufs fails
xfs: reinit btree pointer on attr tree inactivation walk
xfs: Fix bool initialization/comparison
xfs: don't change inode mode if ACL update fails
xfs: move more RT specific code under CONFIG_XFS_RT
xfs: Don't log uninitialised fields in inode structures
Linus Torvalds [Thu, 12 Oct 2017 17:42:03 +0000 (10:42 -0700)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"Another latent bug related to PCID, an out-of-bounds access, and a
submaintainer change being finally made official"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
MAINTAINERS: Add Paul Mackerras as maintainer for KVM/powerpc
KVM: nVMX: fix guest CR4 loading when emulating L2 to L1 exit
KVM: MMU: always terminate page walks at level 1
KVM: nVMX: update last_nonleaf_level when initializing nested EPT
Linus Torvalds [Thu, 12 Oct 2017 16:01:18 +0000 (09:01 -0700)]
Merge tag 'sound-4.14-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"It's been a busy week for defending the attacks from fuzzer people.
This contains various USB-audio driver fixes and sequencer core fixes
spotted by syzkaller and other fuzzer, as well as one quirk for a
Plantronics USB audio device"
* tag 'sound-4.14-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: caiaq: Fix stray URB at probe error path
ALSA: seq: Fix use-after-free at creating a port
ALSA: usb-audio: Kill stray URB at exiting
ALSA: line6: Fix leftover URB at error-path during probe
ALSA: line6: Fix NULL dereference at podhd_disconnect()
ALSA: line6: Fix missing initialization before error path
ALSA: seq: Fix copy_from_user() call inside lock
ALSA: usb-audio: Add sample rate quirk for Plantronics P610
Haozhong Zhang [Tue, 10 Oct 2017 07:01:22 +0000 (15:01 +0800)]
KVM: nVMX: fix guest CR4 loading when emulating L2 to L1 exit
When KVM emulates an exit from L2 to L1, it loads L1 CR4 into the
guest CR4. Before this CR4 loading, the guest CR4 refers to L2
CR4. Because these two CR4's are in different levels of guest, we
should vmx_set_cr4() rather than kvm_set_cr4() here. The latter, which
is used to handle guest writes to its CR4, checks the guest change to
CR4 and may fail if the change is invalid.
The failure may cause trouble. Consider we start
a L1 guest with non-zero L1 PCID in use,
(i.e. L1 CR4.PCIDE == 1 && L1 CR3.PCID != 0)
and
a L2 guest with L2 PCID disabled,
(i.e. L2 CR4.PCIDE == 0)
and following events may happen:
1. If kvm_set_cr4() is used in load_vmcs12_host_state() to load L1 CR4
into guest CR4 (in VMCS01) for L2 to L1 exit, it will fail because
of PCID check. As a result, the guest CR4 recorded in L0 KVM (i.e.
vcpu->arch.cr4) is left to the value of L2 CR4.
2. Later, if L1 attempts to change its CR4, e.g., clearing VMXE bit,
kvm_set_cr4() in L0 KVM will think L1 also wants to enable PCID,
because the wrong L2 CR4 is used by L0 KVM as L1 CR4. As L1
CR3.PCID != 0, L0 KVM will inject GP to L1 guest.
Fixes: 4704d0befb072 ("KVM: nVMX: Exiting from L2 to L1") Cc: qemu-stable@nongnu.org Signed-off-by: Haozhong Zhang <haozhong.zhang@intel.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Fix more return codes for device property: Align return codes of
__acpi_node_get_property_reference().
In particular, what was missed previously:
-EPROTO could be returned in certain cases, now -EINVAL;
-EINVAL was returned if the property was not found, now -ENOENT;
-EINVAL was returned also if the index was higher than the number of
entries in a package, now -ENOENT.
Reported-by: Hyungwoo Yang <hyungwoo.yang@intel.com> Fixes: 3e3119d3088f (device property: Introduce fwnode_property_get_reference_args) Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Tested-by: Hyungwoo Yang <hyungwoo.yang@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Sakari Ailus [Tue, 26 Sep 2017 09:08:27 +0000 (12:08 +0300)]
ACPI: properties: Align return codes of __acpi_node_get_property_reference()
acpi_fwnode_get_reference_args(), the function implementing ACPI
support for fwnode_property_get_reference_args(), returns directly
error codes from __acpi_node_get_property_reference(). The latter
uses different error codes than the OF implementation. In particular,
the OF implementation uses -ENOENT to indicate that the property is
not found, a reference entry is empty and there are no more
references.
Document and align the error codes for property for
fwnode_property_get_reference_args() so that they match with
of_parse_phandle_with_args().
Fixes: 3e3119d3088f (device property: Introduce fwnode_property_get_reference_args) Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Linus Torvalds [Wed, 11 Oct 2017 19:01:38 +0000 (12:01 -0700)]
Merge tag 'rpmsg-v4.14-fixes' of git://github.com/andersson/remoteproc
Pull rpmsg fixes from Bjorn Andersson:
"This corrects two mistakes in the Qualcomm GLINK SMEM driver"
* tag 'rpmsg-v4.14-fixes' of git://github.com/andersson/remoteproc:
rpmsg: glink: Fix memory leak in qcom_glink_alloc_intent()
rpmsg: glink: Unlock on error in qcom_glink_request_intent()
Linus Torvalds [Wed, 11 Oct 2017 18:58:23 +0000 (11:58 -0700)]
Merge tag 'rproc-v4.14-fixes' of git://github.com/andersson/remoteproc
Pull remoteproc fixes from Bjorn Andersson:
"This fixes a couple of issues in the imx_rproc driver and corrects the
Kconfig dependencies of the Qualcomm remoteproc drivers"
* tag 'rproc-v4.14-fixes' of git://github.com/andersson/remoteproc:
remoteproc: imx_rproc: fix return value check in imx_rproc_addr_init()
remoteproc: qcom: fix RPMSG_QCOM_GLINK_SMEM dependencies
remoteproc: imx_rproc: fix a couple off by one bugs
Wei Yongjun [Wed, 11 Oct 2017 10:48:44 +0000 (10:48 +0000)]
remoteproc: imx_rproc: fix return value check in imx_rproc_addr_init()
In case of error, the function devm_ioremap() returns NULL pointer
not ERR_PTR(). The IS_ERR() test in the return value check should
be replaced with NULL test.
Eric Sandeen [Tue, 10 Oct 2017 04:08:06 +0000 (21:08 -0700)]
xfs: handle error if xfs_btree_get_bufs fails
Jason reported that a corrupted filesystem failed to replay
the log with a metadata block out of bounds warning:
XFS (dm-2): _xfs_buf_find: Block out of range: block 0x80270fff8, EOFS 0x9c40000
_xfs_buf_find() and xfs_btree_get_bufs() return NULL if
that happens, and then when xfs_alloc_fix_freelist() calls
xfs_trans_binval() on that NULL bp, we oops with:
BUG: unable to handle kernel NULL pointer dereference at 00000000000000f8
We don't handle _xfs_buf_find errors very well, every
caller higher up the stack gets to guess at why it failed.
But we should at least handle it somehow, so return
EFSCORRUPTED here.
Reported-by: Jason L Tibbitts III <tibbs@math.uh.edu> Signed-off-by: Eric Sandeen <sandeen@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Brian Foster [Mon, 9 Oct 2017 18:38:56 +0000 (11:38 -0700)]
xfs: reinit btree pointer on attr tree inactivation walk
xfs_attr3_root_inactive() walks the attr fork tree to invalidate the
associated blocks. xfs_attr3_node_inactive() recursively descends
from internal blocks to leaf blocks, caching block address values
along the way to revisit parent blocks, locate the next entry and
descend down that branch of the tree.
The code that attempts to reread the parent block is unsafe because
it assumes that the local xfs_da_node_entry pointer remains valid
after an xfs_trans_brelse() and re-read of the parent buffer. Under
heavy memory pressure, it is possible that the buffer has been
reclaimed and reallocated by the time the parent block is reread.
This means that 'btree' can point to an invalid memory address, lead
to a random/garbage value for child_fsb and cause the subsequent
read of the attr fork to go off the rails and return a NULL buffer
for an attr fork offset that is most likely not allocated.
Note that this problem can be manufactured by setting
XFS_ATTR_BTREE_REF to 0 to prevent LRU caching of attr buffers,
creating a file with a multi-level attr fork and removing it to
trigger inactivation.
To address this problem, reinit the node/btree pointers to the
parent buffer after it has been re-read. This ensures btree points
to a valid record and allows the walk to proceed.
Signed-off-by: Brian Foster <bfoster@redhat.com> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Thomas Meyer [Mon, 9 Oct 2017 18:38:54 +0000 (11:38 -0700)]
xfs: Fix bool initialization/comparison
Bool initializations should use true and false. Bool tests don't need
comparisons.
Signed-off-by: Thomas Meyer <thomas@m3y3r.de> Reviewed-by: Brian Foster <bfoster@redhat.com> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Dave Chinner [Mon, 9 Oct 2017 18:37:23 +0000 (11:37 -0700)]
xfs: don't change inode mode if ACL update fails
If we get ENOSPC half way through setting the ACL, the inode mode
can still be changed even though the ACL does not exist. Reorder the
operation to only change the mode of the inode if the ACL is set
correctly.
Whilst this does not fix the problem with crash consistency (that requires
attribute addition to be a deferred op) it does prevent ENOSPC and other
non-fatal errors setting an xattr to be handled sanely.
This fixes xfstests generic/449.
Signed-Off-By: Dave Chinner <dchinner@redhat.com> Reviewed-by: Brian Foster <bfoster@redhat.com> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Dave Chinner [Mon, 9 Oct 2017 18:37:22 +0000 (11:37 -0700)]
xfs: move more RT specific code under CONFIG_XFS_RT
Various utility functions and interfaces that iterate internal
devices try to reference the realtime device even when RT support is
not compiled into the kernel.
Make sure this code is excluded from the CONFIG_XFS_RT=n build,
and where appropriate stub functions to return fatal errors if
they ever get called when RT support is not present.
Signed-Off-By: Dave Chinner <dchinner@redhat.com> Reviewed-by: Brian Foster <bfoster@redhat.com> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Dave Chinner [Mon, 9 Oct 2017 18:37:22 +0000 (11:37 -0700)]
xfs: Don't log uninitialised fields in inode structures
Prevent kmemcheck from throwing warnings about reading uninitialised
memory when formatting inodes into the incore log buffer. There are
several issues here - we don't always log all the fields in the
inode log format item, and we never log the inode the
di_next_unlinked field.
In the case of the inode log format item, this is exacerbated
by the old xfs_inode_log_format structure padding issue. Hence make
the padded, 64 bit aligned version of the structure the one we always
use for formatting the log and get rid of the 64 bit variant. This
means we'll always log the 64-bit version and so recovery only needs
to convert from the unpadded 32 bit version from older 32 bit
kernels.
Signed-Off-By: Dave Chinner <dchinner@redhat.com> Tested-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Reviewed-by: Brian Foster <bfoster@redhat.com> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Alexander Levin [Mon, 10 Apr 2017 18:46:51 +0000 (18:46 +0000)]
9p: set page uptodate when required in write_end()
Commit 77469c3f570 prevented setting the page as uptodate when we wrote
the right amount of data, fix that.
Fixes: 77469c3f570 ("9p: saner ->write_end() on failing copy into non-uptodate page") Reviewed-by: Jan Kara <jack@suse.com> Signed-off-by: Alexander Levin <alexander.levin@verizon.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Wed, 11 Oct 2017 16:16:38 +0000 (09:16 -0700)]
Merge tag 'gpio-v4.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Here are some smallish GPIO fixes for v4.14. Like with pin control:
some build/Kconfig noise and one serious bug in a specific driver.
- Three Kconfig/build warning fixes
- A fix for lost edge IRQs in the OMAP driver"
* tag 'gpio-v4.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: omap: Fix lost edge interrupts
gpio: omap: omap_gpio_show_rev is not __init
gpio: acpi: work around false-positive -Wstring-overflow warning
gpio: thunderx: select IRQ_DOMAIN_HIERARCHY instead of depends on
Linus Torvalds [Wed, 11 Oct 2017 16:00:22 +0000 (09:00 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs fixes from Al Viro:
"Fairly old DIO bug caught by Andreas (3.10+) and several slightly
younger blk_rq_map_user_iov() bugs, both on map and copy codepaths
(Vitaly and me)"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
bio_copy_user_iov(): don't ignore ->iov_offset
more bio_map_user_iov() leak fixes
fix unbalanced page refcounting in bio_map_user_iov
direct-io: Prevent NULL pointer access in submit_page_section
Takashi Iwai [Wed, 11 Oct 2017 14:39:02 +0000 (16:39 +0200)]
ALSA: caiaq: Fix stray URB at probe error path
caiaq driver doesn't kill the URB properly at its error path during
the probe, which may lead to a use-after-free error later. This patch
addresses it.
Reported-by: Johan Hovold <johan@kernel.org> Reviewed-by: Johan Hovold <johan@kernel.org> Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de>
HID: hid-elecom: extend to fix descriptor for HUGE trackball
In addition to DEFT, Elecom introduced a larger trackball called HUGE, in
both wired (M-HT1URBK) and wireless (M-HT1DRBK) versions. It has the same
buttons and behavior as the DEFT. This patch adds the two relevant USB IDs
to enable operation of the three Fn buttons on the top of the device.
Cc: Diego Elio Petteno <flameeyes@flameeyes.eu> Signed-off-by: Alex Manoussakis <amanou@gnu.org> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Jaejoong Kim [Thu, 28 Sep 2017 10:16:30 +0000 (19:16 +0900)]
HID: usbhid: fix out-of-bounds bug
The hid descriptor identifies the length and type of subordinate
descriptors for a device. If the received hid descriptor is smaller than
the size of the struct hid_descriptor, it is possible to cause
out-of-bounds.
In addition, if bNumDescriptors of the hid descriptor have an incorrect
value, this can also cause out-of-bounds while approaching hdesc->desc[n].
So check the size of hid descriptor and bNumDescriptors.
BUG: KASAN: slab-out-of-bounds in usbhid_parse+0x9b1/0xa20
Read of size 1 at addr ffff88006c5f8edf by task kworker/1:2/1261
Joe Lawrence [Mon, 2 Oct 2017 15:56:48 +0000 (11:56 -0400)]
livepatch: unpatch all klp_objects if klp_module_coming fails
When an incoming module is considered for livepatching by
klp_module_coming(), it iterates over multiple patches and multiple
kernel objects in this order:
which means that if one of the kernel objects fails to patch,
klp_module_coming()'s error path needs to unpatch and cleanup any kernel
objects that were already patched by a previous patch.
Reported-by: Miroslav Benes <mbenes@suse.cz> Suggested-by: Petr Mladek <pmladek@suse.com> Signed-off-by: Joe Lawrence <joe.lawrence@redhat.com> Acked-by: Josh Poimboeuf <jpoimboe@redhat.com> Reviewed-by: Petr Mladek <pmladek@suse.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Takashi Iwai [Mon, 9 Oct 2017 09:09:20 +0000 (11:09 +0200)]
ALSA: seq: Fix use-after-free at creating a port
There is a potential race window opened at creating and deleting a
port via ioctl, as spotted by fuzzing. snd_seq_create_port() creates
a port object and returns its pointer, but it doesn't take the
refcount, thus it can be deleted immediately by another thread.
Meanwhile, snd_seq_ioctl_create_port() still calls the function
snd_seq_system_client_ev_port_start() with the created port object
that is being deleted, and this triggers use-after-free like:
We may fix this in a few different ways, and in this patch, it's fixed
simply by taking the refcount properly at snd_seq_create_port() and
letting the caller unref the object after use. Also, there is another
potential use-after-free by sprintf() call in snd_seq_create_port(),
and this is moved inside the lock.
Al Viro [Sun, 24 Sep 2017 14:21:15 +0000 (10:21 -0400)]
bio_copy_user_iov(): don't ignore ->iov_offset
Since "block: support large requests in blk_rq_map_user_iov" we
started to call it with partially drained iter; that works fine
on the write side, but reads create a copy of iter for completion
time. And that needs to take the possibility of ->iov_iter != 0
into account...
Cc: stable@vger.kernel.org #v4.5+ Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Sat, 23 Sep 2017 19:51:23 +0000 (15:51 -0400)]
more bio_map_user_iov() leak fixes
we need to take care of failure exit as well - pages already
in bio should be dropped by analogue of bio_unmap_pages(),
since their refcounts had been bumped only once per reference
in bio.
Cc: stable@vger.kernel.org Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
fix unbalanced page refcounting in bio_map_user_iov
bio_map_user_iov and bio_unmap_user do unbalanced pages refcounting if
IO vector has small consecutive buffers belonging to the same page.
bio_add_pc_page merges them into one, but the page reference is never
dropped.
Cc: stable@vger.kernel.org Signed-off-by: Vitaly Mayatskikh <v.mayatskih@gmail.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
direct-io: Prevent NULL pointer access in submit_page_section
In the code added to function submit_page_section by commit b1058b981,
sdio->bio can currently be NULL when calling dio_bio_submit. This then
leads to a NULL pointer access in dio_bio_submit, so check for a NULL
bio in submit_page_section before trying to submit it instead.
Fixes xfstest generic/250 on gfs2.
Cc: stable@vger.kernel.org # v3.10+ Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Reviewed-by: Jan Kara <jack@suse.cz> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Linus Torvalds [Tue, 10 Oct 2017 20:08:59 +0000 (13:08 -0700)]
Merge tag 'seccomp-v4.14-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull seccomp fixlet from Kees Cook:
"Minor seccomp fix for v4.14-rc5. I debated sending this at all for
v4.14, but since it fixes a minor issue in the prior fix, which also
went to -stable, it seemed better to just get all of it cleaned up
right now.
- fix missed "static" to avoid Sparse warning (Colin King)"
* tag 'seccomp-v4.14-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
seccomp: make function __get_seccomp_filter static
Linus Torvalds [Tue, 10 Oct 2017 20:01:51 +0000 (13:01 -0700)]
Merge tag 'nfsd-4.14-1' of git://linux-nfs.org/~bfields/linux
Pull nfsd fix from Bruce Fields:
"One fix for a 4.14 regression, and one minor fix to the MAINTAINERs
file. (I was weirdly flattered by the idea that lots of random people
suddenly seemed to think Jeff and I were VFS experts. Turns out it was
just a typo)"
* tag 'nfsd-4.14-1' of git://linux-nfs.org/~bfields/linux:
nfsd4: define nfsd4_secinfo_no_name_release()
MAINTAINERS: associate linux/fs.h with VFS instead of file locking
Colin Ian King [Fri, 29 Sep 2017 13:26:48 +0000 (14:26 +0100)]
seccomp: make function __get_seccomp_filter static
The function __get_seccomp_filter is local to the source and does
not need to be in global scope, so make it static.
Cleans up sparse warning:
symbol '__get_seccomp_filter' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com> Fixes: 66a733ea6b61 ("seccomp: fix the usage of get/put_seccomp_filter() in seccomp_get_filter()") Cc: stable@vger.kernel.org Signed-off-by: Kees Cook <keescook@chromium.org>
When RPMSG_QCOM_GLINK_SMEM=m and one driver causes the qcom_common.c file
to be compiled as built-in, we get a link error:
drivers/remoteproc/qcom_common.o: In function `glink_subdev_remove':
qcom_common.c:(.text+0x130): undefined reference to `qcom_glink_smem_unregister'
qcom_common.c:(.text+0x130): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `qcom_glink_smem_unregister'
drivers/remoteproc/qcom_common.o: In function `glink_subdev_probe':
qcom_common.c:(.text+0x160): undefined reference to `qcom_glink_smem_register'
qcom_common.c:(.text+0x160): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `qcom_glink_smem_register'
Out of the three PIL driver instances, QCOM_ADSP_PIL already has a
Kconfig dependency to prevent this from happening, but the other two
do not. This adds the same dependency there.
Linus Torvalds [Tue, 10 Oct 2017 17:57:46 +0000 (10:57 -0700)]
Merge tag 'linux-kselftest-4.14-rc5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull kselftest fixes from Shuah Khan:
- fix for x86: sysret_ss_attrs test build failure preventing the x86
tests from running
- fix mqueue: fix regression in silencing test run output
* tag 'linux-kselftest-4.14-rc5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests: mqueue: fix regression in silencing output from RUN_TESTS
selftests: x86: sysret_ss_attrs doesn't build on a PIE build
The shash ahash digest adaptor function may crash if given a
zero-length input together with a null SG list. This is because
it tries to read the SG list before looking at the length.
This patch fixes it by checking the length first.
Cc: <stable@vger.kernel.org> Reported-by: Stephan Müller<smueller@chronox.de> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Tested-by: Stephan Müller <smueller@chronox.de>
Jan Kara [Tue, 10 Oct 2017 12:40:42 +0000 (14:40 +0200)]
quota: Generate warnings for DQUOT_SPACE_NOFAIL allocations
Eryu has reported that since commit 7b9ca4c61bc2 "quota: Reduce
contention on dq_data_lock" test generic/233 occasionally fails. This is
caused by the fact that since that commit we don't generate warning and
set grace time for quota allocations that have DQUOT_SPACE_NOFAIL set
(these are for example some metadata allocations in ext4). We need these
allocations to behave regularly wrt warning generation and grace time
setting so fix the code to return to the original behavior.
Reported-and-tested-by: Eryu Guan <eguan@redhat.com> CC: stable@vger.kernel.org Fixes: 7b9ca4c61bc278b771fb57d6290a31ab1fc7fdac Signed-off-by: Jan Kara <jack@suse.cz>
Ladi Prosek [Thu, 5 Oct 2017 09:10:23 +0000 (11:10 +0200)]
KVM: MMU: always terminate page walks at level 1
is_last_gpte() is not equivalent to the pseudo-code given in commit 6bb69c9b69c31 ("KVM: MMU: simplify last_pte_bitmap") because an incorrect
value of last_nonleaf_level may override the result even if level == 1.
It is critical for is_last_gpte() to return true on level == 1 to
terminate page walks. Otherwise memory corruption may occur as level
is used as an index to various data structures throughout the page
walking code. Even though the actual bug would be wherever the MMU is
initialized (as in the previous patch), be defensive and ensure here
that is_last_gpte() returns the correct value.
This patch is also enough to fix CVE-2017-12188.
Fixes: 6bb69c9b69c315200ddc2bc79aee14c0184cf5b2 Cc: stable@vger.kernel.org Cc: Andy Honig <ahonig@google.com> Signed-off-by: Ladi Prosek <lprosek@redhat.com>
[Panic if walk_addr_generic gets an incorrect level; this is a serious
bug and it's not worth a WARN_ON where the recovery path might hide
further exploitable issues; suggested by Andrew Honig. - Paolo] Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Ladi Prosek [Thu, 5 Oct 2017 09:10:22 +0000 (11:10 +0200)]
KVM: nVMX: update last_nonleaf_level when initializing nested EPT
The function updates context->root_level but didn't call
update_last_nonleaf_level so the previous and potentially wrong value
was used for page walks. For example, a zero value of last_nonleaf_level
would allow a potential out-of-bounds access in arch/x86/mmu/paging_tmpl.h's
walk_addr_generic function (CVE-2017-12188).
Fixes: 155a97a3d7c78b46cef6f1a973c831bc5a4f82bb Signed-off-by: Ladi Prosek <lprosek@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Takashi Iwai [Tue, 10 Oct 2017 12:10:32 +0000 (14:10 +0200)]
ALSA: usb-audio: Kill stray URB at exiting
USB-audio driver may leave a stray URB for the mixer interrupt when it
exits by some error during probe. This leads to a use-after-free
error as spotted by syzkaller like:
==================================================================
BUG: KASAN: use-after-free in snd_usb_mixer_interrupt+0x604/0x6f0
Call Trace:
<IRQ>
__dump_stack lib/dump_stack.c:16
dump_stack+0x292/0x395 lib/dump_stack.c:52
print_address_description+0x78/0x280 mm/kasan/report.c:252
kasan_report_error mm/kasan/report.c:351
kasan_report+0x23d/0x350 mm/kasan/report.c:409
__asan_report_load8_noabort+0x19/0x20 mm/kasan/report.c:430
snd_usb_mixer_interrupt+0x604/0x6f0 sound/usb/mixer.c:2490
__usb_hcd_giveback_urb+0x2e0/0x650 drivers/usb/core/hcd.c:1779
....
Actually such a URB is killed properly at disconnection when the
device gets probed successfully, and what we need is to apply it for
the error-path, too.
In this patch, we apply snd_usb_mixer_disconnect() at releasing.
Also introduce a new flag, disconnected, to struct usb_mixer_interface
for not performing the disconnection procedure twice.
Jarkko Nikula [Mon, 9 Oct 2017 13:28:37 +0000 (16:28 +0300)]
device property: Track owner device of device property
Deletion of subdevice will remove device properties associated to parent
when they share the same firmware node after commit 478573c93abd (driver
core: Don't leak secondary fwnode on device removal). This was observed
with a driver adding subdevice that driver wasn't able to read device
properties after rmmod/modprobe cycle.
Parent device will have its primary firmware node pointing to an ACPI
node and secondary firmware node point to device properties.
ACPI_COMPANION_SET() call in parent probe will set the subdevice's
firmware node to point to the same 'struct fwnode_handle' and the
associated secondary firmware node, i.e. the device properties as the
parent.
When subdevice is deleted in parent remove that will remove those
device properties and attempt to read device properties in next
parent probe call will fail.
Fix this by tracking the owner device of device properties and delete
them only when owner device is being deleted.
Fixes: 478573c93abd (driver core: Don't leak secondary fwnode on device removal) Cc: 4.9+ <stable@vger.kernel.org> # 4.9+ Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Linus Torvalds [Tue, 10 Oct 2017 02:08:32 +0000 (19:08 -0700)]
Merge branch 'ppc-bundle' (bundle from Michael Ellerman)
Merge powerpc transactional memory fixes from Michael Ellerman:
"I figured I'd still send you the commits using a bundle to make sure
it works in case I need to do it again in future"
This fixes transactional memory state restore for powerpc.
* bundle'd patches from Michael Ellerman:
powerpc/tm: Fix illegal TM state in signal handler
powerpc/64s: Use emergency stack for kernel TM Bad Thing program checks
1) Fix object leak on IPSEC offload failure, from Steffen Klassert.
2) Fix range checks in ipset address range addition operations, from
Jozsef Kadlecsik.
3) Fix pernet ops unregistration order in ipset, from Florian Westphal.
4) Add missing netlink attribute policy for nl80211 packet pattern
attrs, from Peng Xu.
5) Fix PPP device destruction race, from Guillaume Nault.
6) Write marks get lost when BPF verifier processes R1=R2 register
assignments, causing incorrect liveness information and less state
pruning. Fix from Alexei Starovoitov.
7) Fix blockhole routes so that they are marked dead and therefore not
cached in sockets, otherwise IPSEC stops working. From Steffen
Klassert.
8) Fix broadcast handling of UDP socket early demux, from Paolo Abeni.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (37 commits)
cdc_ether: flag the u-blox TOBY-L2 and SARA-U2 as wwan
net: thunderx: mark expected switch fall-throughs in nicvf_main()
udp: fix bcast packet reception
netlink: do not set cb_running if dump's start() errs
ipv4: Fix traffic triggered IPsec connections.
ipv6: Fix traffic triggered IPsec connections.
ixgbe: incorrect XDP ring accounting in ethtool tx_frame param
net: ixgbe: Use new PCI_DEV_FLAGS_NO_RELAXED_ORDERING flag
Revert commit 1a8b6d76dc5b ("net:add one common config...")
ixgbe: fix masking of bits read from IXGBE_VXLANCTRL register
ixgbe: Return error when getting PHY address if PHY access is not supported
netfilter: xt_bpf: Fix XT_BPF_MODE_FD_PINNED mode of 'xt_bpf_info_v1'
netfilter: SYNPROXY: skip non-tcp packet in {ipv4, ipv6}_synproxy_hook
tipc: Unclone message at secondary destination lookup
tipc: correct initialization of skb list
gso: fix payload length when gso_size is zero
mlxsw: spectrum_router: Avoid expensive lookup during route removal
bpf: fix liveness marking
doc: Fix typo "8023.ad" in bonding documentation
ipv6: fix net.ipv6.conf.all.accept_dad behaviour for real
...
cdc_ether: flag the u-blox TOBY-L2 and SARA-U2 as wwan
The u-blox TOBY-L2 is a LTE Cat 4 module with HSPA+ and 2G fallback.
This module allows switching to different USB profiles with the
'AT+UUSBCONF' command, and provides a ECM network interface when the
'AT+UUSBCONF=2' profile is selected.
The u-blox SARA-U2 is a HSPA module with 2G fallback. The default USB
configuration includes a ECM network interface.
Both these modules are controlled via AT commands through one of the
TTYs exposed. Connecting these modules may be done just by activating
the desired PDP context with 'AT+CGACT=1,<cid>' and then running DHCP
on the ECM interface.
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es> Signed-off-by: David S. Miller <davem@davemloft.net>
bugfixes:
- NFSv4/pnfs: Fix an infinite layoutget loop
- nfs: RPC_MAX_AUTH_SIZE is in bytes"
* tag 'nfs-for-4.14-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFSv4/pnfs: Fix an infinite layoutget loop
nfs/filelayout: fix oops when freeing filelayout segment
sunrpc: remove redundant initialization of sock
NFS: Fix uninitialized rpc_wait_queue
NFS: Cleanup error handling in nfs_idmap_request_key()
nfs: RPC_MAX_AUTH_SIZE is in bytes
net: thunderx: mark expected switch fall-throughs in nicvf_main()
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Cc: Sunil Goutham <sgoutham@cavium.com> Cc: Robert Richter <rric@kernel.org> Cc: linux-arm-kernel@lists.infradead.org Cc: netdev@vger.kernel.org Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 9 Oct 2017 17:36:25 +0000 (10:36 -0700)]
Merge branch '10GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-queue
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2017-10-09
This series contains updates to ixgbe and arch/Kconfig.
Mark fixes a case where PHY register access is not supported and we were
returning a PHY address, when we should have been returning -EOPNOTSUPP.
Sabrina Dubroca fixes the use of a logical "and" when it should have been
the bitwise "and" operator.
Ding Tianhong reverts the commit that added the Kconfig bool option
ARCH_WANT_RELAX_ORDER, since there is now a new flag
PCI_DEV_FLAGS_NO_RELAXED_ORDERING that has been added to indicate that
Relaxed Ordering Attributes should not be used for Transaction Layer
Packets. Then follows up with making the needed changes to ixgbe to
use the new PCI_DEV_FLAGS_NO_RELAXED_ORDERING flag.
John Fastabend fixes an issue in the ring accounting when the transmit
ring parameters are changed via ethtool when an XDP program is attached.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Mon, 9 Oct 2017 12:52:10 +0000 (14:52 +0200)]
udp: fix bcast packet reception
The commit bc044e8db796 ("udp: perform source validation for
mcast early demux") does not take into account that broadcast packets
lands in the same code path and they need different checks for the
source address - notably, zero source address are valid for bcast
and invalid for mcast.
As a result, 2nd and later broadcast packets with 0 source address
landing to the same socket are dropped. This breaks dhcp servers.
Since we don't have stringent performance requirements for ingress
broadcast traffic, fix it by disabling UDP early demux such traffic.
Reported-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Fixes: bc044e8db796 ("udp: perform source validation for mcast early demux") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
netlink: do not set cb_running if dump's start() errs
It turns out that multiple places can call netlink_dump(), which means
it's still possible to dereference partially initialized values in
dump() that were the result of a faulty returned start().
This fixes the issue by calling start() _before_ setting cb_running to
true, so that there's no chance at all of hitting the dump() function
through any indirect paths.
It also moves the call to start() to be when the mutex is held. This has
the nice side effect of serializing invocations to start(), which is
likely desirable anyway. It also prevents any possible other races that
might come out of this logic.
In testing this with several different pieces of tricky code to trigger
these issues, this commit fixes all avenues that I'm aware of.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Cc: Johannes Berg <johannes@sipsolutions.net> Reviewed-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: David S. Miller <davem@davemloft.net>
The QCA folks found another netlink problem - we were missing validation
of some attributes. It's not super problematic since one can only read a
few bytes beyond the message (and that memory must exist), but here's the
fix for it.
I thought perhaps we can make nla_parse_nested() require a policy, but
given the two-stage validation/parsing in regular netlink that won't work.
Please pull and let me know if there's any problem.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
A recent patch removed the dst_free() on the allocated
dst_entry in ipv4_blackhole_route(). The dst_free() marked the
dst_entry as dead and added it to the gc list. I.e. it was setup
for a one time usage. As a result we may now have a blackhole
route cached at a socket on some IPsec scenarios. This makes the
connection unusable.
Fix this by marking the dst_entry directly at allocation time
as 'dead', so it is used only once.
Fixes: b838d5e1c5b6 ("ipv4: mark DST_NOGC and remove the operation of dst_free()") Reported-by: Tobias Brunner <tobias@strongswan.org> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: David S. Miller <davem@davemloft.net>
A recent patch removed the dst_free() on the allocated
dst_entry in ipv6_blackhole_route(). The dst_free() marked
the dst_entry as dead and added it to the gc list. I.e. it
was setup for a one time usage. As a result we may now have
a blackhole route cached at a socket on some IPsec scenarios.
This makes the connection unusable.
Fix this by marking the dst_entry directly at allocation time
as 'dead', so it is used only once.
Fixes: 587fea741134 ("ipv6: mark DST_NOGC and remove the operation of dst_free()") Reported-by: Tobias Brunner <tobias@strongswan.org> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: David S. Miller <davem@davemloft.net>
John Fastabend [Thu, 7 Sep 2017 17:32:48 +0000 (10:32 -0700)]
ixgbe: incorrect XDP ring accounting in ethtool tx_frame param
Changing the TX ring parameters with an XDP program attached may
cause the XDP queues to be cleared and the TX rings to be incorrectly
configured.
Fix by doing correct ring accounting in setup call.
Fixes: 33fdc82f0883 ("ixgbe: add support for XDP_TX action") Signed-off-by: John Fastabend <john.fastabend@gmail.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Ding Tianhong [Fri, 18 Aug 2017 06:21:05 +0000 (14:21 +0800)]
net: ixgbe: Use new PCI_DEV_FLAGS_NO_RELAXED_ORDERING flag
The ixgbe driver use the compile check to determine if it can
send TLPs to Root Port with the Relaxed Ordering Attribute set,
this is too inconvenient, now the new flag PCI_DEV_FLAGS_NO_RELAXED_ORDERING
has been added to the kernel and we could check the bit4 in the PCIe
Device Control register to determine whether we should use the Relaxed
Ordering Attributes or not, so use this new way in the ixgbe driver.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com> Acked-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Ding Tianhong [Fri, 18 Aug 2017 06:21:04 +0000 (14:21 +0800)]
Revert commit 1a8b6d76dc5b ("net:add one common config...")
The new flag PCI_DEV_FLAGS_NO_RELAXED_ORDERING has been added
to indicate that Relaxed Ordering Attributes (RO) should not
be used for Transaction Layer Packets (TLP) targeted toward
these affected Root Port, it will clear the bit4 in the PCIe
Device Control register, so the PCIe device drivers could
query PCIe configuration space to determine if it can send
TLPs to Root Port with the Relaxed Ordering Attributes set.
With this new flag we don't need the config ARCH_WANT_RELAX_ORDER
to control the Relaxed Ordering Attributes for the ixgbe drivers
just like the commit 1a8b6d76dc5b ("net:add one common config...") did,
so revert this commit.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ixgbe: fix masking of bits read from IXGBE_VXLANCTRL register
In ixgbe_clear_udp_tunnel_port(), we read the IXGBE_VXLANCTRL register
and then try to mask some bits out of the value, using the logical
instead of bitwise and operator.
Fixes: a21d0822ff69 ("ixgbe: add support for geneve Rx offload") Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mark D Rustad [Wed, 31 Aug 2016 17:34:28 +0000 (10:34 -0700)]
ixgbe: Return error when getting PHY address if PHY access is not supported
In cases where PHY register access is not supported, don't mislead
a caller into thinking that it is supported by returning a PHY
address. Instead, return -EOPNOTSUPP when PHY access is not
supported.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Takashi Iwai [Mon, 9 Oct 2017 12:51:23 +0000 (14:51 +0200)]
ALSA: line6: Fix leftover URB at error-path during probe
While line6_probe() may kick off URB for a control MIDI endpoint, the
function doesn't clean up it properly at its error path. This results
in a leftover URB action that is eventually triggered later and causes
an Oops like:
general protection fault: 0000 [#1] PREEMPT SMP KASAN
CPU: 1 PID: 0 Comm: swapper/1 Not tainted
RIP: 0010:usb_fill_bulk_urb ./include/linux/usb.h:1619
RIP: 0010:line6_start_listen+0x3fe/0x9e0 sound/usb/line6/driver.c:76
Call Trace:
<IRQ>
line6_data_received+0x1f7/0x470 sound/usb/line6/driver.c:326
__usb_hcd_giveback_urb+0x2e0/0x650 drivers/usb/core/hcd.c:1779
usb_hcd_giveback_urb+0x337/0x420 drivers/usb/core/hcd.c:1845
dummy_timer+0xba9/0x39f0 drivers/usb/gadget/udc/dummy_hcd.c:1965
call_timer_fn+0x2a2/0x940 kernel/time/timer.c:1281
....
Since the whole clean-up procedure is done in line6_disconnect()
callback, we can simply call it in the error path instead of
open-coding the whole again. It'll fix such an issue automagically.
Takashi Iwai [Mon, 9 Oct 2017 12:26:27 +0000 (14:26 +0200)]
ALSA: line6: Fix NULL dereference at podhd_disconnect()
When podhd_init() failed with the acquiring a ctrl i/f, the line6
helper still calls the disconnect callback that eventually calls again
usb_driver_release_interface() with the NULL intf.
Put the proper NULL check before calling it for avoiding an Oops.
Fixes: fc90172ba283 ("ALSA: line6: Claim pod x3 usb data interface") Reported-by: Andrey Konovalov <andreyknvl@google.com> Tested-by: Andrey Konovalov <andreyknvl@google.com> Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai [Mon, 9 Oct 2017 12:32:15 +0000 (14:32 +0200)]
ALSA: line6: Fix missing initialization before error path
The error path in podhd_init() tries to clear the pending timer, while
the timer object is initialized at the end of init sequence, thus it
may hit the uninitialized object, as spotted by syzkaller:
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
CPU: 1 PID: 1845 Comm: kworker/1:2 Not tainted 4.14.0-rc2-42613-g1488251d1a98 #238
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
Workqueue: usb_hub_wq hub_event
Call Trace:
__dump_stack lib/dump_stack.c:16
dump_stack+0x292/0x395 lib/dump_stack.c:52
register_lock_class+0x6c4/0x1a00 kernel/locking/lockdep.c:769
__lock_acquire+0x27e/0x4550 kernel/locking/lockdep.c:3385
lock_acquire+0x259/0x620 kernel/locking/lockdep.c:4002
del_timer_sync+0x12c/0x280 kernel/time/timer.c:1237
podhd_disconnect+0x8c/0x160 sound/usb/line6/podhd.c:299
line6_probe+0x844/0x1310 sound/usb/line6/driver.c:783
podhd_probe+0x64/0x70 sound/usb/line6/podhd.c:474
....
For addressing it, assure the initializations of timer and work by
moving them to the beginning of podhd_init().
Fixes: 790869dacc3d ("ALSA: line6: Add support for POD X3") Reported-by: Andrey Konovalov <andreyknvl@google.com> Tested-by: Andrey Konovalov <andreyknvl@google.com> Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Shmulik Ladkani [Mon, 9 Oct 2017 12:27:15 +0000 (15:27 +0300)]
netfilter: xt_bpf: Fix XT_BPF_MODE_FD_PINNED mode of 'xt_bpf_info_v1'
Commit 2c16d6033264 ("netfilter: xt_bpf: support ebpf") introduced
support for attaching an eBPF object by an fd, with the
'bpf_mt_check_v1' ABI expecting the '.fd' to be specified upon each
IPT_SO_SET_REPLACE call.
However this breaks subsequent iptables calls:
# iptables -A INPUT -m bpf --object-pinned /sys/fs/bpf/xxx -j ACCEPT
# iptables -A INPUT -s 5.6.7.8 -j ACCEPT
iptables: Invalid argument. Run `dmesg' for more information.
That's because iptables works by loading existing rules using
IPT_SO_GET_ENTRIES to userspace, then issuing IPT_SO_SET_REPLACE with
the replacement set.
However, the loaded 'xt_bpf_info_v1' has an arbitrary '.fd' number
(from the initial "iptables -m bpf" invocation) - so when 2nd invocation
occurs, userspace passes a bogus fd number, which leads to
'bpf_mt_check_v1' to fail.
One suggested solution [1] was to hack iptables userspace, to perform a
"entries fixup" immediatley after IPT_SO_GET_ENTRIES, by opening a new,
process-local fd per every 'xt_bpf_info_v1' entry seen.
However, in [2] both Pablo Neira Ayuso and Willem de Bruijn suggested to
depricate the xt_bpf_info_v1 ABI dealing with pinned ebpf objects.
This fix changes the XT_BPF_MODE_FD_PINNED behavior to ignore the given
'.fd' and instead perform an in-kernel lookup for the bpf object given
the provided '.path'.
It also defines an alias for the XT_BPF_MODE_FD_PINNED mode, named
XT_BPF_MODE_PATH_PINNED, to better reflect the fact that the user is
expected to provide the path of the pinned object.
Existing XT_BPF_MODE_FD_ELF behavior (non-pinned fd mode) is preserved.
Reported-by: Rafael Buchbinder <rafi@rbk.ms> Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com> Acked-by: Willem de Bruijn <willemb@google.com> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Takashi Iwai [Mon, 9 Oct 2017 08:02:56 +0000 (10:02 +0200)]
ALSA: seq: Fix copy_from_user() call inside lock
The event handler in the virmidi sequencer code takes a read-lock for
the linked list traverse, while it's calling snd_seq_dump_var_event()
in the loop. The latter function may expand the user-space data
depending on the event type. It eventually invokes copy_from_user(),
which might be a potential dead-lock.
The sequencer core guarantees that the user-space data is passed only
with atomic=0 argument, but snd_virmidi_dev_receive_event() ignores it
and always takes read-lock(). For avoiding the problem above, this
patch introduces rwsem for non-atomic case, while keeping rwlock for
atomic case.
Also while we're at it: the superfluous irq flags is dropped in
snd_virmidi_input_open().
Reported-by: Jia-Ju Bai <baijiaju1990@163.com> Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Lin Zhang [Thu, 5 Oct 2017 16:44:03 +0000 (00:44 +0800)]
netfilter: SYNPROXY: skip non-tcp packet in {ipv4, ipv6}_synproxy_hook
In function {ipv4,ipv6}_synproxy_hook we expect a normal tcp packet, but
the real server maybe reply an icmp error packet related to the exist
tcp conntrack, so we will access wrong tcp data.
Fix it by checking for the protocol field and only process tcp traffic.
Signed-off-by: Lin Zhang <xiaolou4617@gmail.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Jon Maloy [Sat, 7 Oct 2017 13:07:20 +0000 (15:07 +0200)]
tipc: Unclone message at secondary destination lookup
When a bundling message is received, the function tipc_link_input()
calls function tipc_msg_extract() to unbundle all inner messages of
the bundling message before adding them to input queue.
The function tipc_msg_extract() just clones all inner skb for all
inner messagges from the bundling skb. This means that the skb
headroom of an inner message overlaps with the data part of the
preceding message in the bundle.
If the message in question is a name addressed message, it may be
subject to a secondary destination lookup, and eventually be sent out
on one of the interfaces again. But, since what is perceived as headroom
by the device driver in reality is the last bytes of the preceding
message in the bundle, the latter will be overwritten by the MAC
addresses of the L2 header. If the preceding message has not yet been
consumed by the user, it will evenually be delivered with corrupted
contents.
This commit fixes this by uncloning all messages passing through the
function tipc_msg_lookup_dest(), hence ensuring that the headroom
is always valid when the message is passed on.
Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Maloy [Sat, 7 Oct 2017 12:32:49 +0000 (14:32 +0200)]
tipc: correct initialization of skb list
We change the initialization of the skb transmit buffer queues
in the functions tipc_bcast_xmit() and tipc_rcast_xmit() to also
initialize their spinlocks. This is needed because we may, during
error conditions, need to call skb_queue_purge() on those queues
further down the stack.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexey Kodanev [Fri, 6 Oct 2017 16:02:35 +0000 (19:02 +0300)]
gso: fix payload length when gso_size is zero
When gso_size reset to zero for the tail segment in skb_segment(), later
in ipv6_gso_segment(), __skb_udp_tunnel_segment() and gre_gso_segment()
we will get incorrect results (payload length, pcsum) for that segment.
inet_gso_segment() already has a check for gso_size before calculating
payload.
The issue was found with LTP vxlan & gre tests over ixgbe NIC.
Fixes: 07b26c9454a2 ("gso: Support partial splitting at the frag_list pointer") Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com> Acked-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Sun, 8 Oct 2017 09:53:26 +0000 (11:53 +0200)]
mlxsw: spectrum_router: Avoid expensive lookup during route removal
In commit fc922bb0dd94 ("mlxsw: spectrum_router: Use one LPM tree for
all virtual routers") I increased the scale of supported VRFs by having
all of them share the same LPM tree.
In order to avoid look-ups for prefix lengths that don't exist, each
route removal would trigger an aggregation across all the active virtual
routers to see which prefix lengths are in use and which aren't and
structure the tree accordingly.
With the way the data structures are currently laid out, this is a very
expensive operation. When preformed repeatedly - due to the invocation
of the abort mechanism - and with enough VRFs, this can result in a hung
task.
For now, avoid this optimization until it can be properly re-added in
net-next.
Fixes: fc922bb0dd94 ("mlxsw: spectrum_router: Use one LPM tree for all virtual routers") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reported-by: David Ahern <dsa@cumulusnetworks.com> Tested-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
pinctrl: cherryview: fix issues caused by dynamic gpio irqs mapping
New GPIO IRQs are allocated and mapped dynamically by default when
GPIO IRQ infrastructure is used by cherryview-pinctrl driver.
This causes issues on some Intel platforms [1][2] with broken BIOS which
hardcodes Linux IRQ numbers in their ACPI tables.
On such platforms cherryview-pinctrl driver should allocate and map all
GPIO IRQs at probe time.
Side effect - "Cannot allocate irq_descs @ IRQ%d, assuming pre-allocated\n"
can be seen at boot log.
NOTE. It still may fail if boot sequence will changed and some interrupt
controller will be probed before cherryview-pinctrl which will shift Linux IRQ
numbering (expected with CONFIG_SPARCE_IRQ enabled).
[1] https://bugzilla.kernel.org/show_bug.cgi?id=194945
[2] https://lkml.org/lkml/2017/9/28/153 Cc: Andy Shevchenko <andy.shevchenko@gmail.com> Cc: Chris Gorman <chrisjohgorman@gmail.com> Cc: Mika Westerberg <mika.westerberg@linux.intel.com> Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Reported-by: Chris Gorman <chrisjohgorman@gmail.com> Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com> Tested-by: Chris Gorman <chrisjohgorman@gmail.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
while processing Rx = Ry instruction the verifier does
regs[insn->dst_reg] = regs[insn->src_reg]
which often clears write mark (when Ry doesn't have it)
that was just set by check_reg_arg(Rx) prior to the assignment.
That causes mark_reg_read() to keep marking Rx in this block as
REG_LIVE_READ (since the logic incorrectly misses that it's
screened by the write) and in many of its parents (until lucky
write into the same Rx or beginning of the program).
That causes is_state_visited() logic to miss many pruning opportunities.
Furthermore mark_reg_read() logic propagates the read mark
for BPF_REG_FP as well (though it's readonly) which causes
harmless but unnecssary work during is_state_visited().
Note that do_propagate_liveness() skips FP correctly,
so do the same in mark_reg_read() as well.
It saves 0.2 seconds for the test below
program before after
bpf_lb-DLB_L3.o 2604 2304
bpf_lb-DLB_L4.o 11159 3723
bpf_lb-DUNKNOWN.o 1116 1110
bpf_lxc-DDROP_ALL.o 34566 28004
bpf_lxc-DUNKNOWN.o 53267 39026
bpf_netdev.o 17843 16943
bpf_overlay.o 8672 7929
time ~11 sec ~4 sec
Fixes: dc503a8ad984 ("bpf/verifier: track liveness for pruning") Signed-off-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Edward Cree <ecree@solarflare.com> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Matteo Croce [Thu, 5 Oct 2017 17:03:05 +0000 (19:03 +0200)]
ipv6: fix net.ipv6.conf.all.accept_dad behaviour for real
Commit 35e015e1f577 ("ipv6: fix net.ipv6.conf.all interface DAD handlers")
was intended to affect accept_dad flag handling in such a way that
DAD operation and mode on a given interface would be selected
according to the maximum value of conf/{all,interface}/accept_dad.
However, addrconf_dad_begin() checks for particular cases in which we
need to skip DAD, and this check was modified in the wrong way.
Namely, it was modified so that, if the accept_dad flag is 0 for the
given interface *or* for all interfaces, DAD would be skipped.
We have instead to skip DAD if accept_dad is 0 for the given interface
*and* for all interfaces.
Fixes: 35e015e1f577 ("ipv6: fix net.ipv6.conf.all interface DAD handlers") Acked-by: Stefano Brivio <sbrivio@redhat.com> Signed-off-by: Matteo Croce <mcroce@redhat.com> Reported-by: Erik Kline <ek@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 7 Oct 2017 17:07:51 +0000 (10:07 -0700)]
Merge branch 'i2c/for-current-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"I2C has three driver fixes for the newly introduced drivers and one ID
addition for the i801 driver"
* 'i2c/for-current-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: i2c-stm32f7: make structure stm32f7_setup static const
i2c: ensure termination of *_device_id tables
i2c: i801: Add support for Intel Cedar Fork
i2c: stm32f7: fix setup structure
Linus Torvalds [Sat, 7 Oct 2017 17:03:03 +0000 (10:03 -0700)]
Merge tag 'mmc-v4.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"MMC core:
- Fix driver strength selection when selecting hs400es
- Delete bounce buffer handling:
This change fixes a problem related to how bounce buffers are being
allocated. However, instead of trying to fix that, let's just
remove the mmc bounce buffer code altogether, as it has practically
no use.
MMC host:
- meson-gx: A couple of fixes related to clock/phase/tuning
- sdhci-xenon: Fix clock resource by adding an optional bus clock"
* tag 'mmc-v4.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: sdhci-xenon: Fix clock resource by adding an optional bus clock
mmc: meson-gx: include tx phase in the tuning process
mmc: meson-gx: fix rx phase reset
mmc: meson-gx: make sure the clock is rounded down
mmc: Delete bounce buffer handling
mmc: core: add driver strength selection when selecting hs400es
Now acking of edge irqs happens the following way:
- omap_gpio_irq_handler
- "isr" = read irq status
- omap_clear_gpio_irqbank(bank, isr_saved & ~level_mask);
^ clear edge status, so irq can be accepted
- loop while "isr"
generic_handle_irq()
- handle_edge_irq()
- desc->irq_data.chip->irq_ack(&desc->irq_data);
- omap_gpio_ack_irq()
it might be that at this moment edge IRQ was triggered again and it will be
cleared and IRQ will be lost.
Use handle_simple_irq and clear edge interrupts early without disabling them in
omap_gpio_irq_handler to avoid loosing interrupts.
Herbert Xu [Sat, 7 Oct 2017 03:29:48 +0000 (11:29 +0800)]
crypto: skcipher - Fix crash on zero-length input
The skcipher walk interface doesn't handle zero-length input
properly as the old blkcipher walk interface did. This is due
to the fact that the length check is done too late.
This patch moves the length check forward so that it does the
right thing.
Fixes: b286d8b1a690 ("crypto: skcipher - Add skcipher walk...") Cc: <stable@vger.kernel.org> Reported-by: Stephan Müller <smueller@chronox.de> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Jia-Ju Bai [Tue, 3 Oct 2017 02:25:22 +0000 (10:25 +0800)]
crypto: shash - Fix a sleep-in-atomic bug in shash_setkey_unaligned
The SCTP program may sleep under a spinlock, and the function call path is:
sctp_generate_t3_rtx_event (acquire the spinlock)
sctp_do_sm
sctp_side_effects
sctp_cmd_interpreter
sctp_make_init_ack
sctp_pack_cookie
crypto_shash_setkey
shash_setkey_unaligned
kmalloc(GFP_KERNEL)
For the same reason, the orinoco driver may sleep in interrupt handler,
and the function call path is:
orinoco_rx_isr_tasklet
orinoco_rx
orinoco_mic
crypto_shash_setkey
shash_setkey_unaligned
kmalloc(GFP_KERNEL)
To fix it, GFP_KERNEL is replaced with GFP_ATOMIC.
This bug is found by my static analysis tool and my code review.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
projects / mirror_ubuntu-disco-kernel.git / log