Anton Blanchard [Sat, 25 Mar 2006 06:25:17 +0000 (17:25 +1100)]
[PATCH] powerpc: Allow non zero boot cpuids
We currently have a hack to flip the boot cpu and its secondary thread
to logical cpuid 0 and 1. This means the logical - physical mapping will
differ depending on which cpu is boot cpu. This is most apparent on
kexec, where we might kexec on any cpu and therefore change the mapping
from boot to boot.
The patch below does a first pass early on to work out the logical cpuid
of the boot thread. We then fix up some paca structures to match.
Ive also removed the boot_cpuid_phys variable for ppc64, to be
consistent we use get_hard_smp_processor_id(boot_cpuid) everywhere.
Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Arnd Bergmann [Fri, 24 Mar 2006 18:49:27 +0000 (19:49 +0100)]
[PATCH] spufs: Fix endless protection fault on LS writes by SPE.
If an SPE attempts a DMA put to a local store after already doing
a get, the kernel must update the HW PTE to allow the write access.
This case was not being handled correctly.
From: Mike Kistler <mkistler@us.ibm.com> Signed-off-by: Mike Kistler <mkistler@us.ibm.com> Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Olaf Hering [Thu, 23 Mar 2006 20:50:59 +0000 (21:50 +0100)]
[PATCH] correct the comment about stackpointer alignment in __boot_from_prom
The address of variable val in prom_init_stdout is passed to prom_getprop.
prom_getprop casts the pointer to u32 and passes it to call_prom in the hope
that OpenFirmware stores something there.
But the pointer is truncated in the lower bits and the expected value is
stored somewhere else.
In my testing I had a stackpointer of 0x0023e6b4. val was at offset 120,
wich has address 0x0023e72c. But the value passed to OF was 0x0023e728.
The stackpointer came from 32bit code.
The chain was yaboot -> zImage -> vmlinux
PowerMac OpenFirmware does appearently not handle the ELF sections
correctly. If yaboot was compiled in
/usr/src/packages/BUILD/lilo-10.1.1/yaboot, then the stackpointer is
unaligned. But the stackpointer is correct if yaboot is compiled in
/tmp/yaboot.
This bug triggered since 2.6.15, now prom_getprop is an inline
function. gcc clears the lower bits, instead of just clearing the
upper 32 bits.
Signed-off-by: Olaf Hering <olh@suse.de> Signed-off-by: Paul Mackerras <paulus@samba.org>
Mark Nutter [Wed, 22 Mar 2006 23:00:12 +0000 (00:00 +0100)]
[PATCH] spufs: enable SPE problem state MMIO access.
This patch is layered on top of CONFIG_SPARSEMEM
and is patterned after direct mapping of LS.
This patch allows mmap() of the following regions:
"mfc", which represents the area from [0x3000 - 0x3fff];
"cntl", which represents the area from [0x4000 - 0x4fff];
"signal1" which begins at offset 0x14000; "signal2" which
begins at offset 0x1c000.
The signal1 & signal2 files may be mmap()'d by regular user
processes. The cntl and mfc file, on the other hand, may
only be accessed if the owning process has CAP_SYS_RAWIO,
because they have the potential to confuse the kernel
with regard to parallel access to the same files with
regular file operations: the kernel always holds a spinlock
when accessing registers in these areas to serialize them,
which can not be guaranteed with user mmaps,
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Arnd Bergmann [Wed, 22 Mar 2006 23:00:11 +0000 (00:00 +0100)]
[PATCH] spufs: implement mfc access for PPE-side DMA
This patch adds a new file called 'mfc' to each spufs directory.
The file accepts DMA commands that are a subset of what would
be legal DMA commands for problem state register access. Upon
reading the file, a bitmask is returned with the completed
tag groups set.
The file is meant to be used from an abstraction in libspe
that is added by a different patch.
From the kernel perspective, this means a process can now
offload a memory copy from or into an SPE local store
without having to run code on the SPE itself.
The transfer will only be performed while the SPE is owned
by one thread that is waiting in the spu_run system call
and the data will be transferred into that thread's
address space, independent of which thread started the
transfer.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Arnd Bergmann [Wed, 22 Mar 2006 23:00:09 +0000 (00:00 +0100)]
[PATCH] spufs: allow SPU code to do syscalls
An SPU does not have a way to implement system calls
itself, but it can create intercepts to the kernel.
This patch uses the method defined by the JSRE interface
for C99 host library calls from an SPU to implement
Linux system calls. It uses the reserved SPU stop code
0x2104 for this, using the structure layout and syscall
numbers for ppc64-linux.
I'm still undecided wether it is better to have a list
of allowed syscalls or a list of forbidden syscalls,
since we can't allow an SPU to call all syscalls that
are defined for ppc64-linux.
This patch implements the easier choice of them, with a
blacklist that only prevents an SPU from calling anything
that interacts with its own execution, e.g fork, execve,
clone, vfork, exit, spu_run and spu_create and everything
that deals with signals.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Arnd Bergmann [Wed, 22 Mar 2006 23:00:08 +0000 (00:00 +0100)]
[PATCH] powerpc: declare arch syscalls in <asm/syscalls.h>
powerpc currently declares some of its own system calls
in <asm/unistd.h>, but not all of them. That place also
contains remainders of the now almost unused kernel syscall
hack.
- Add a new <asm/syscalls.h> with clean declarations
- Include that file from every source that implements one
of these
- Get rid of old declarations in <asm/unistd.h>
This patch is required as a base for implementing system
calls from an SPU, but also makes sense as a general
cleanup.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Arnd Bergmann [Wed, 22 Mar 2006 23:00:07 +0000 (00:00 +0100)]
[PATCH] powerpc: work around a cell interrupt HW bug
Apparently we have found a bug in the CPU that causes
external interrupts to sometimes get disabled indefinitely.
This adds a workaround for the problem.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
The current interrupt controller setup on Cell is done
in a rather ad-hoc way with device tree properties
that are not standardized at all.
In an attempt to do something that follows the OF standard
(or at least the IBM extensions to it) more closely,
we have now come up with this patch. It still provides
a fallback to the old behaviour when we find older firmware,
that hack can not be removed until the existing customer
installations have upgraded.
Arnd Bergmann [Wed, 22 Mar 2006 23:00:04 +0000 (00:00 +0100)]
[PATCH] powerpc: fix cell iommu setup
A small bug crept in the iommu driver when we made it more
generic. This patch is needed for boards that have a dma
window that does not start at bus address zero.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Michael Ellerman [Thu, 23 Mar 2006 12:33:03 +0000 (23:33 +1100)]
[PATCH] powerpc: Change firmware_has_feature() to a macro
So that we can use firmware_has_feature() in a BUG_ON() and have the compiler
elide the code entirely if the feature can never be set, change
firmware_has_feature to a macro. Unfortunate, but necessary at least until
GCC bug #26724 is fixed.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
Michael Ellerman [Thu, 23 Mar 2006 12:32:24 +0000 (23:32 +1100)]
[PATCH] powerpc: Make BUG_ON & WARN_ON play nice with compile-time optimisations
Change BUG_ON and WARN_ON to give the compiler a chance to perform
compile-time optimsations. Depending on the complexity of the condition,
the compiler may not do this very well, so if it's important check the
object code.
Current GCC's (4.x) produce good code as long as the condition does not
include a function call, including a static inline.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
Stephen Rothwell [Thu, 23 Mar 2006 06:36:59 +0000 (17:36 +1100)]
[PATCH] powerpc: work around sparse warnings in cputable.h
Christoph noticed that sparse warned about all the enum tags in cuptable.h
that had values that required them to be type log. (enum tags are ints
according to the standard.)
This patch attempts to fix them in the least intrusive way possible by
turning them all into #defines except for the 32 bit CPU_FTRS_POSSIBLE and
CPU_FTRS_ALWAYS which are hard to construct that way. This works because
these last two contain no bits above 2^31.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial:
drivers/char/ftape/lowlevel/fdc-io.c: Correct a comment
Kconfig help: MTD_JEDECPROBE already supports Intel
Remove ugly debugging stuff
do_mounts.c: Minor ROOT_DEV comment cleanup
BUG_ON() Conversion in drivers/s390/block/dasd_devmap.c
BUG_ON() Conversion in mm/mempool.c
BUG_ON() Conversion in mm/memory.c
BUG_ON() Conversion in kernel/fork.c
BUG_ON() Conversion in ipc/sem.c
BUG_ON() Conversion in fs/ext2/
BUG_ON() Conversion in fs/hfs/
BUG_ON() Conversion in fs/dcache.c
BUG_ON() Conversion in fs/buffer.c
BUG_ON() Conversion in input/serio/hp_sdc_mlc.c
BUG_ON() Conversion in md/dm-table.c
BUG_ON() Conversion in md/dm-path-selector.c
BUG_ON() Conversion in drivers/isdn
BUG_ON() Conversion in drivers/char
BUG_ON() Conversion in drivers/mtd/
Akinobu Mita [Sun, 26 Mar 2006 09:40:00 +0000 (01:40 -0800)]
[PATCH] bitops: hweight() speedup
<linux@horizon.com> wrote:
This is an extremely well-known technique. You can see a similar version that
uses a multiply for the last few steps at
http://graphics.stanford.edu/~seander/bithacks.html#CountBitsSetParallel whch
refers to "Software Optimization Guide for AMD Athlon 64 and Opteron
Processors"
http://www.amd.com/us-en/assets/content_type/white_papers_and_tech_docs/25112.PDF
It's section 8.6, "Efficient Implementation of Population-Count Function in
32-bit Mode", pages 179-180.
It uses the name that I am more familiar with, "popcount" (population count),
although "Hamming weight" also makes sense.
Anyway, the proof of correctness proceeds as follows:
b = a - ((a >> 1) & 0x55555555);
c = (b & 0x33333333) + ((b >> 2) & 0x33333333);
d = (c + (c >> 4)) & 0x0f0f0f0f;
#if SLOW_MULTIPLY
e = d + (d >> 8)
f = e + (e >> 16);
return f & 63;
#else
/* Useful if multiply takes at most 4 cycles */
return (d * 0x01010101) >> 24;
#endif
The input value a can be thought of as 32 1-bit fields each holding their own
hamming weight. Now look at it as 16 2-bit fields. Each 2-bit field a1..a0
has the value 2*a1 + a0. This can be converted into the hamming weight of the
2-bit field a1+a0 by subtracting a1.
That's what the (a >> 1) & mask subtraction does. Since there can be no
borrows, you can just do it all at once.
The next step consists of breaking up b (made of 16 2-bir fields) into
even and odd halves and adding them into 4-bit fields. Since the largest
possible sum is 2+2 = 4, which will not fit into a 4-bit field, the 2-bit
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
"which will not fit into a 2-bit field"
fields have to be masked before they are added.
After this point, the masking can be delayed. Each 4-bit field holds a
population count from 0..4, taking at most 3 bits. These numbers can be added
without overflowing a 4-bit field, so we can compute c + (c >> 4), and only
then mask off the unwanted bits.
This produces d, a number of 4 8-bit fields, each in the range 0..8. From
this point, we can shift and add d multiple times without overflowing an 8-bit
field, and only do a final mask at the end.
The number to mask with has to be at least 63 (so that 32 on't be truncated),
but can also be 128 or 255. The x86 has a special encoding for signed
immediate byte values -128..127, so the value of 255 is slower. On other
processors, a special "sign extend byte" instruction might be faster.
On a processor with fast integer multiplies (Athlon but not P4), you can
reduce the final few serially dependent instructions to a single integer
multiply. Consider d to be 3 8-bit values d3, d2, d1 and d0, each in the
range 0..8. The multiply forms the partial products:
Akinobu Mita [Sun, 26 Mar 2006 09:39:53 +0000 (01:39 -0800)]
[PATCH] bitops: ia64: make partial_page.bitmap an unsigned long
The find_*_bit() routines are defined to work on a pointer to unsigned long.
But partial_page.bitmap is unsigned int and it is passed to find_*_bit() in
arch/ia64/ia32/sys_ia32.c. So the compiler will print warnings.
This patch changes to unsigned long instead.
Signed-off-by: Akinobu Mita <mita@miraclelinux.com> Cc: "Luck, Tony" <tony.luck@intel.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Akinobu Mita [Sun, 26 Mar 2006 09:39:51 +0000 (01:39 -0800)]
[PATCH] bitops: sh: make thread_info.flags an unsigned long
The test_bit() routines are defined to work on a pointer to unsigned long.
But thread_info.flags is __u32 (unsigned int) on sh and it is passed to flag
set/clear/test wrappers in include/linux/thread_info.h. So the compiler will
print warnings.
This patch changes to unsigned long instead.
Signed-off-by: Akinobu Mita <mita@miraclelinux.com> Cc: Paul Mundt <lethal@linux-sh.org> Cc: Kazumoto Kojima <kkojima@rr.iij4u.or.jp> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently include/asm-generic/bitops.h is not referenced from anywhere. But
it will be the benefit of those who are trying to port Linux to another
architecture.
So update it by same manner
Signed-off-by: Akinobu Mita <mita@miraclelinux.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Akinobu Mita <mita@miraclelinux.com> Cc: William Lee Irwin III <wli@holomorphy.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Akinobu Mita <mita@miraclelinux.com> Cc: Paul Mundt <lethal@linux-sh.org> Cc: Richard Curnow <rc@rc0.org.uk> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Akinobu Mita <mita@miraclelinux.com> Cc: Paul Mundt <lethal@linux-sh.org> Cc: Kazumoto Kojima <kkojima@rr.iij4u.or.jp> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Akinobu Mita <mita@miraclelinux.com> Cc: Paul Mackerras <paulus@samba.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Akinobu Mita <mita@miraclelinux.com> Cc: Russell King <rmk@arm.linux.org.uk> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Akinobu Mita <mita@miraclelinux.com> Cc: Richard Henderson <rth@twiddle.net> Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch introduces the C-language equivalents of the functions below:
int minix_test_and_set_bit(int nr, volatile unsigned long *addr);
int minix_set_bit(int nr, volatile unsigned long *addr);
int minix_test_and_clear_bit(int nr, volatile unsigned long *addr);
int minix_test_bit(int nr, const volatile unsigned long *addr);
unsigned long minix_find_first_zero_bit(const unsigned long *addr,
unsigned long size);
In include/asm-generic/bitops/minix.h
and include/asm-generic/bitops/minix-le.h
This code largely copied from: include/asm-sparc/bitops.h
Signed-off-by: Akinobu Mita <mita@miraclelinux.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch introduces the C-language equivalents of the functions below:
int ext2_set_bit(int nr, volatile unsigned long *addr);
int ext2_clear_bit(int nr, volatile unsigned long *addr);
int ext2_test_bit(int nr, const volatile unsigned long *addr);
unsigned long ext2_find_first_zero_bit(const unsigned long *addr,
unsigned long size);
unsinged long ext2_find_next_zero_bit(const unsigned long *addr,
unsigned long size);
Akinobu Mita [Sun, 26 Mar 2006 09:39:13 +0000 (01:39 -0800)]
[PATCH] bitops: generic hweight{64,32,16,8}()
This patch introduces the C-language equivalents of the functions below:
unsigned int hweight32(unsigned int w);
unsigned int hweight16(unsigned int w);
unsigned int hweight8(unsigned int w);
unsigned long hweight64(__u64 w);
In include/asm-generic/bitops/hweight.h
This code largely copied from: include/linux/bitops.h
Signed-off-by: Akinobu Mita <mita@miraclelinux.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch introduces the C-language equivalents of the functions below:
unsigned logn find_next_bit(const unsigned long *addr, unsigned long size,
unsigned long offset);
unsigned long find_next_zero_bit(const unsigned long *addr, unsigned long size,
unsigned long offset);
unsigned long find_first_zero_bit(const unsigned long *addr,
unsigned long size);
unsigned long find_first_bit(const unsigned long *addr, unsigned long size);
In include/asm-generic/bitops/find.h
This code largely copied from: arch/powerpc/lib/bitops.c
Signed-off-by: Akinobu Mita <mita@miraclelinux.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Akinobu Mita [Sun, 26 Mar 2006 09:39:07 +0000 (01:39 -0800)]
[PATCH] bitops: generic __{,test_and_}{set,clear,change}_bit() and test_bit()
This patch introduces the C-language equivalents of the functions below:
void __set_bit(int nr, volatile unsigned long *addr);
void __clear_bit(int nr, volatile unsigned long *addr);
void __change_bit(int nr, volatile unsigned long *addr);
int __test_and_set_bit(int nr, volatile unsigned long *addr);
int __test_and_clear_bit(int nr, volatile unsigned long *addr);
int __test_and_change_bit(int nr, volatile unsigned long *addr);
int test_bit(int nr, const volatile unsigned long *addr);
In include/asm-generic/bitops/non-atomic.h
This code largely copied from: asm-powerpc/bitops.h
Signed-off-by: Akinobu Mita <mita@miraclelinux.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch introduces the C-language equivalents of the functions below:
void set_bit(int nr, volatile unsigned long *addr);
void clear_bit(int nr, volatile unsigned long *addr);
void change_bit(int nr, volatile unsigned long *addr);
int test_and_set_bit(int nr, volatile unsigned long *addr);
int test_and_clear_bit(int nr, volatile unsigned long *addr);
int test_and_change_bit(int nr, volatile unsigned long *addr);
Akinobu Mita [Sun, 26 Mar 2006 09:39:05 +0000 (01:39 -0800)]
[PATCH] bitops: use non atomic operations for minix_*_bit() and ext2_*_bit()
Bitmap functions for the minix filesystem and the ext2 filesystem except
ext2_set_bit_atomic() and ext2_clear_bit_atomic() do not require the atomic
guarantees.
But these are defined by using atomic bit operations on several architectures.
(cris, frv, h8300, ia64, m32r, m68k, m68knommu, mips, s390, sh, sh64, sparc,
sparc64, v850, and xtensa)
This patch switches to non atomic bit operation.
Signed-off-by: Akinobu Mita <mita@miraclelinux.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Akinobu Mita [Sun, 26 Mar 2006 09:39:01 +0000 (01:39 -0800)]
[PATCH] bitops: alpha: use config options instead of __alpha_fix__ and __alpha_cix__
Use config options instead of gcc builtin definition to tell the use of
instruction set extensions (CIX and FIX).
This is introduced to tell the kbuild system the use of opmized hweight*()
routines on alpha architecture.
Signed-off-by: Akinobu Mita <mita@miraclelinux.com> Cc: Richard Henderson <rth@twiddle.net> Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Richard Knutsson [Sun, 26 Mar 2006 09:39:00 +0000 (01:39 -0800)]
[PATCH] oss/sonicvibes.c defines its own hweight32
sound/oss/sonicvibes.c:421: error: static declaration of hweight32 follows non-static declaration
include/asm-generic/bitops/hweight.h:6: error: previous declaration of hweight32 was here
Signed-off-by: Richard Knutsson <ricknu-0@student.ltu.se> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Akinobu Mita [Sun, 26 Mar 2006 09:38:59 +0000 (01:38 -0800)]
[PATCH] arm: fix undefined reference to generic_fls
This patch defines constant_fls() instead of removed generic_fls().
Signed-off-by: Akinobu Mita <mita@miraclelinux.com> Cc: Russell King <rmk@arm.linux.org.uk> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Akinobu Mita [Sun, 26 Mar 2006 09:38:57 +0000 (01:38 -0800)]
[PATCH] frv: remove unnesesary "&"
Fix warning messages triggered by bitops code consolidation patches.
cxn_bitmap is the array of unsigned long. '&' is unnesesary for the argument
of *_bit() routins.
Signed-off-by: Akinobu Mita <mita@miraclelinux.com> Acked-by: David Howells <dhowells@redhat.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Dave Peterson [Sun, 26 Mar 2006 09:38:55 +0000 (01:38 -0800)]
[PATCH] EDAC: use EXPORT_SYMBOL_GPL
Change all instances of EXPORT_SYMBOL() in the core EDAC module to
EXPORT_SYMBOL_GPL().
Signed-off-by: David S. Peterson <dsp@llnl.gov> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Dave Peterson [Sun, 26 Mar 2006 09:38:50 +0000 (01:38 -0800)]
[PATCH] EDAC: protect memory controller list
- Fix code so we always hold mem_ctls_mutex while we are stepping
through the list of mem_ctl_info structures. Otherwise bad things
may happen if one task is stepping through the list while another
task is modifying it. We may eventually want to use reference
counting to manage the mem_ctl_info structures. In the meantime we
may as well fix this bug.
- Don't disable interrupts while we are walking the list of
mem_ctl_info structures in check_mc_devices(). This is unnecessary.
Signed-off-by: David S. Peterson <dsp@llnl.gov> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Dave Peterson [Sun, 26 Mar 2006 09:38:49 +0000 (01:38 -0800)]
[PATCH] EDAC: kobject/sysfs fixes
- After we unregister a kobject, wait for our kobject release method
to call complete(). This causes us to wait until the kobject
reference count reaches 0. Otherwise, a task accessing the EDAC
sysfs interface can hold the reference count above 0 until after the
EDAC module has been unloaded. When the reference count finally
drops to 0, this will result in an attempt to call our release
method inside the EDAC module after the module has already been
unloaded.
This isn't the best fix, since a process can get stuck sleeping forever
uninterruptibly if the user does the following:
rmmod my_module < /sys/my_sysfs/file
I'll go back and implement a better fix later. However this should
be ok for now.
- Call edac_remove_sysfs_mci_device() from edac_mc_del_mc() rather
than from edac_mc_free(). Since edac_mc_add_mc() calls
edac_create_sysfs_mci_device(), edac_mc_del_mc() should call
edac_remove_sysfs_mci_device().
Signed-off-by: David S. Peterson <dsp@llnl.gov> Cc: Greg KH <greg@kroah.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Dave Peterson [Sun, 26 Mar 2006 09:38:48 +0000 (01:38 -0800)]
[PATCH] EDAC: kobject_init/kobject_put fixes
- Remove calls to kobject_init(). These are unnecessary because
kobject_register() calls kobject_init().
- Remove extra calls to kobject_put(). When we call
kobject_unregister(), this releases our reference to the kobject.
The extra calls to kobject_put() may cause the reference count to
drop to 0 while a kobject is still in use.
Signed-off-by: David S. Peterson <dsp@llnl.gov> Cc: Greg KH <greg@kroah.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Dave Peterson [Sun, 26 Mar 2006 09:38:46 +0000 (01:38 -0800)]
[PATCH] EDAC: edac_mc_add_mc fix [1/2]
This is part 1 of a 2-part patch set. The code changes are split into
two parts to make the patches more readable.
Move complete_mc_list_del() and del_mc_from_global_list() so we can
call del_mc_from_global_list() from edac_mc_add_mc() without forward
declarations. Perhaps using forward declarations would be better?
I'm doing things this way because the rest of the code is missing
them.
Signed-off-by: David S. Peterson <dsp@llnl.gov> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Dave Peterson [Sun, 26 Mar 2006 09:38:45 +0000 (01:38 -0800)]
[PATCH] EDAC: cleanup code for clearing initial errors
Fix xxx_probe1() functions so they call xxx_get_error_info() functions
to clear initial errors. This is simpler and cleaner than duplicating
the low-level code for accessing PCI config space.
Signed-off-by: David S. Peterson <dsp@llnl.gov> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
projects / mirror_ubuntu-jammy-kernel.git / log