It is insecure to allow arbitrary hash algorithms and signature
encodings to be used with arbitrary signature algorithms. Notably,
ECDSA, ECRDSA, and SM2 all sign/verify raw hash values and don't
disambiguate between different hash algorithms like RSA PKCS#1 v1.5
padding does. Therefore, they need to be restricted to certain sets of
hash algorithms (ideally just one, but in practice small sets are used).
Additionally, the encoding is an integral part of modern signature
algorithms, and is not supposed to vary.
Therefore, tighten the checks of hash_algo and encoding done by
software_key_determine_akcipher().
Also rearrange the parameters to software_key_determine_akcipher() to
put the public_key first, as this is the most important parameter and it
often determines everything else.
Fixes: 299f561a6693 ("x509: Add support for parsing x509 certs with ECDSA keys") Fixes: 215525639631 ("X.509: support OSCCA SM2-with-SM3 certificate verification") Fixes: 0d7a78643f69 ("crypto: ecrdsa - add EC-RDSA (GOST 34.10) algorithm") Cc: stable@vger.kernel.org Tested-by: Stefan Berger <stefanb@linux.ibm.com> Tested-by: Tianjia Zhang <tianjia.zhang@linux.alibaba.com> Signed-off-by: Eric Biggers <ebiggers@google.com> Reviewed-by: Vitaly Chikunov <vt@altlinux.org> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit a1e55db51a88a9578c0f6c99a8cd9dc6cb20711c) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Most callers of public_key_verify_signature(), including most indirect
callers via verify_signature() as well as pkcs7_verify_sig_chain(),
don't check that public_key_signature::pkey_algo matches
public_key::pkey_algo. These should always match. However, a malicious
signature could intentionally declare an unintended algorithm. It is
essential that such signatures be rejected outright, or that the
algorithm of the *key* be used -- not the algorithm of the signature as
that would allow attackers to choose the algorithm used.
Currently, public_key_verify_signature() correctly uses the key's
algorithm when deciding which akcipher to allocate. That's good.
However, it uses the signature's algorithm when deciding whether to do
the first step of SM2, which is incorrect. Also, v4.19 and older
kernels used the signature's algorithm for the entire process.
Prevent such errors by making public_key_verify_signature() enforce that
the signature's algorithm (if given) matches the key's algorithm.
Also remove two checks of this done by callers, which are now redundant.
Cc: stable@vger.kernel.org Tested-by: Stefan Berger <stefanb@linux.ibm.com> Tested-by: Tianjia Zhang <tianjia.zhang@linux.alibaba.com> Signed-off-by: Eric Biggers <ebiggers@google.com> Reviewed-by: Vitaly Chikunov <vt@altlinux.org> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 255921f63a9ee59371d62f15017c5fd251dcac56) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
In many cases, keyctl_pkey_params_get_2() is validating the user buffer
lengths against the wrong algorithm properties. Fix it to check against
the correct properties.
Probably this wasn't noticed before because for all asymmetric keys of
the "public_key" subtype, max_data_size == max_sig_size == max_enc_size
== max_dec_size. However, this isn't necessarily true for the
"asym_tpm" subtype (it should be, but it's not strictly validated). Of
course, future key types could have different values as well.
Fixes: 00d60fd3b932 ("KEYS: Provide keyctls to drive the new key type ops for asymmetric keys [ver #2]") Cc: <stable@vger.kernel.org> # v4.20+ Signed-off-by: Eric Biggers <ebiggers@google.com> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit fe8df44892407e301ed03027639b4d904f12694c) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Remove the spinlock around the tree traversal as we are calling possibly
sleeping functions.
We do not need a spinlock here as there will be no modifications to this
tree at this point.
This prevents warnings like this to occur in dmesg:
[ 653.774996] BUG: sleeping function called from invalid context at kernel/loc\
king/mutex.c:280
[ 653.775088] in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 1827, nam\
e: umount
[ 653.775152] preempt_count: 1, expected: 0
[ 653.775191] CPU: 0 PID: 1827 Comm: umount Tainted: G W OE 5.17.0\
-rc7-00006-g4eb628dd74df #135
[ 653.775195] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.14.0-\
1.fc33 04/01/2014
[ 653.775197] Call Trace:
[ 653.775199] <TASK>
[ 653.775202] dump_stack_lvl+0x34/0x44
[ 653.775209] __might_resched.cold+0x13f/0x172
[ 653.775213] mutex_lock+0x75/0xf0
[ 653.775217] ? __mutex_lock_slowpath+0x10/0x10
[ 653.775220] ? _raw_write_lock_irq+0xd0/0xd0
[ 653.775224] ? dput+0x6b/0x360
[ 653.775228] cifs_kill_sb+0xff/0x1d0 [cifs]
[ 653.775285] deactivate_locked_super+0x85/0x130
[ 653.775289] cleanup_mnt+0x32c/0x4d0
[ 653.775292] ? path_umount+0x228/0x380
[ 653.775296] task_work_run+0xd8/0x180
[ 653.775301] exit_to_user_mode_loop+0x152/0x160
[ 653.775306] exit_to_user_mode_prepare+0x89/0xd0
[ 653.775315] syscall_exit_to_user_mode+0x12/0x30
[ 653.775322] do_syscall_64+0x48/0x90
[ 653.775326] entry_SYSCALL_64_after_hwframe+0x44/0xae
Fixes: 187af6e98b44e5d8f25e1d41a92db138eb54416f ("cifs: fix handlecache and multiuser") Reported-by: kernel test robot <oliver.sang@intel.com> Cc: stable@vger.kernel.org Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 512bde6420870f5403e253866d8de7a2267275bb) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
In multiuser each individual user has their own tcon structure for the
share and thus their own handle for a cached directory.
When we umount such a share we much make sure to release the pinned down dentry
for each such tcon and not just the master tcon.
Otherwise we will get nasty warnings on umount that dentries are still in use:
[ 3459.590047] BUG: Dentry 00000000115c6f41{i=12000000019d95,n=/} still in use\
(2) [unmount of cifs cifs]
...
[ 3459.590492] Call Trace:
[ 3459.590500] d_walk+0x61/0x2a0
[ 3459.590518] ? shrink_lock_dentry.part.0+0xe0/0xe0
[ 3459.590526] shrink_dcache_for_umount+0x49/0x110
[ 3459.590535] generic_shutdown_super+0x1a/0x110
[ 3459.590542] kill_anon_super+0x14/0x30
[ 3459.590549] cifs_kill_sb+0xf5/0x104 [cifs]
[ 3459.590773] deactivate_locked_super+0x36/0xa0
[ 3459.590782] cleanup_mnt+0x131/0x190
[ 3459.590789] task_work_run+0x5c/0x90
[ 3459.590798] exit_to_user_mode_loop+0x151/0x160
[ 3459.590809] exit_to_user_mode_prepare+0x83/0xd0
[ 3459.590818] syscall_exit_to_user_mode+0x12/0x30
[ 3459.590828] do_syscall_64+0x48/0x90
[ 3459.590833] entry_SYSCALL_64_after_hwframe+0x44/0xae
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com> Acked-by: Paulo Alcantara (SUSE) <pc@cjr.nz> Cc: stable@vger.kernel.org Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 2fafbc198613823943c106d1ec9b516da692059f) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Fixed-rate clocks in UniPhier don't have any parent clocks, however,
initial data "init.flags" isn't initialized, so it might be determined
that there is a parent clock for fixed-rate clock.
In commit 4e7cf74fa3b2 ("clk: fractional-divider: Export approximation
algorithm to the CCF users"), the code handling the rational best
approximation algorithm was replaced by a call to the core
clk_fractional_divider_general_approximation function which did the same
thing back then.
However, in commit 82f53f9ee577 ("clk: fractional-divider: Introduce
POWER_OF_TWO_PS flag"), this common code was made conditional on
CLK_FRAC_DIVIDER_POWER_OF_TWO_PS flag which was not added back to the
rockchip clock driver.
This broke the ltk050h3146w-a2 MIPI DSI display present on a PX30-based
downstream board.
Let's add the flag to the fractional divider flags so that the original
and intended behavior is brought back to the rockchip clock drivers.
iio_convert_raw_to_processed_unlocked() assumes the offset is an
integer. Make a best effort to get a valid offset value for fractional
cases without breaking implicit truncations.
Fixes: 48e44ce0f881 ("iio:inkern: Add function to read the processed value") Signed-off-by: Liam Beguin <liambeguin@gmail.com> Reviewed-by: Peter Rosin <peda@axentia.se> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Link: https://lore.kernel.org/r/20220108205319.2046348-4-liambeguin@gmail.com Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 9e97f6641c878bc7ce7f4eac835142a7e9d07c11) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
When a consumer calls iio_read_channel_processed() and no channel scale
is available, it's assumed that the scale is one and the raw value is
returned as expected.
On the other hand, if the consumer calls iio_convert_raw_to_processed()
the scaling factor requested by the consumer is not applied.
This for example causes the consumer to process mV when expecting uV.
Make sure to always apply the scaling factor requested by the consumer.
Fixes: adc8ec5ff183 ("iio: inkern: pass through raw values if no scaling") Signed-off-by: Liam Beguin <liambeguin@gmail.com> Reviewed-by: Peter Rosin <peda@axentia.se> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Link: https://lore.kernel.org/r/20220108205319.2046348-3-liambeguin@gmail.com Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit b378d3f585e3a4d7cc63fedda92edbf844468910) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
When a consumer calls iio_read_channel_processed() and the channel has
an integer scale, the scale channel scale is applied and the processed
value is returned as expected.
On the other hand, if the consumer calls iio_convert_raw_to_processed()
the scaling factor requested by the consumer is not applied.
This for example causes the consumer to process mV when expecting uV.
Make sure to always apply the scaling factor requested by the consumer.
Fixes: 48e44ce0f881 ("iio:inkern: Add function to read the processed value") Signed-off-by: Liam Beguin <liambeguin@gmail.com> Reviewed-by: Peter Rosin <peda@axentia.se> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Link: https://lore.kernel.org/r/20220108205319.2046348-2-liambeguin@gmail.com Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit e3858236210184f0bfc2dd7f5188573b54084d5f) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
All four scaling coefficients can take signed values.
Make tmp a signed 64-bit integer and switch to div_s64() to preserve
signs during 64-bit divisions.
Fixes: 8b74816b5a9a ("iio: afe: rescale: new driver") Signed-off-by: Liam Beguin <liambeguin@gmail.com> Reviewed-by: Peter Rosin <peda@axentia.se> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Link: https://lore.kernel.org/r/20220108205319.2046348-5-liambeguin@gmail.com Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 1cb35faea3c3ba101199b9e16561cc2328a985a1) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
It's impossible to program a valid value for TRCCONFIGR.QE
when TRCIDR0.QSUPP==0b10. In that case the following is true:
Q element support is implemented, and only supports Q elements without
instruction counts. TRCCONFIGR.QE can only take the values 0b00 or 0b11.
Currently the low bit of QSUPP is checked to see if the low bit of QE can
be written to, but as you can see when QSUPP==0b10 the low bit is cleared
making it impossible to ever write the only valid value of 0b11 to QE.
0b10 would be written instead, which is a reserved QE value even for all
values of QSUPP.
The fix is to allow writing the low bit of QE for any non zero value of
QSUPP.
This change also ensures that the low bit is always set, even when the
user attempts to only set the high bit.
Signed-off-by: James Clark <james.clark@arm.com> Reviewed-by: Mike Leach <mike.leach@linaro.org> Fixes: d8c66962084f ("coresight-etm4x: Controls pertaining to the reset, mode, pe and events") Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20220120113047.2839622-2-james.clark@arm.com Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org> Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit ba81399402b7d3dee1b8dfb92c008d90da0cd580) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
jinja2 release 3.1.0 (March 24, 2022) broke Sphinx<4.0.
This looks like the result of deprecating Python 3.6.
It has been tested against Sphinx 4.3.0 and later.
Setting an upper limit of <3.1 to junja2 can unbreak Sphinx<4.0
including Sphinx 2.4.4.
The MHI driver does not work on big endian architectures. The
controller never transitions into mission mode. This appears to be due
to the modem device expecting the various contexts and transfer rings to
have fields in little endian order in memory, but the driver constructs
them in native endianness.
Fix MHI event, channel and command contexts and TRE handling macros to
use explicit conversion to little endian. Mark fields in relevant
structures as little endian to document this requirement.
Fixes: a6e2e3522f29 ("bus: mhi: core: Add support for PM state transitions") Fixes: 6cd330ae76ff ("bus: mhi: core: Add support for ringing channel/event ring doorbells") Cc: stable@vger.kernel.org Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Reviewed-by: Alex Elder <elder@linaro.org> Signed-off-by: Paul Davey <paul.davey@alliedtelesis.co.nz> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Link: https://lore.kernel.org/r/20220301160308.107452-4-manivannan.sadhasivam@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit c1013a5ba4c9611132f306e7cd46c5931305ecfb) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
For default mechanism, the driver uses default MRU 3500 if mru_default
is not initialized. The Qualcomm configured the MRU size to 32768 in the
WWAN device FW. So, we align the driver setting with Qualcomm FW setting.
Usage of the iterator outside of the list_for_each_entry
is considered harmful. https://lkml.org/lkml/2022/2/17/1032
Do not reference the loop variable outside of the loop,
by rearranging the orders of execution.
Instead of performing search loop and checking outside the loop
if the end of the list was hit and no matching element was found,
the execution is performed inside the loop upon a successful match
followed by a goto statement to the next step,
therefore no condition has to be performed after the loop has ended.
xhci_decode_ctrl_ctx() returns the untouched buffer as-is if both "drop"
and "add" parameters are zero.
Fix the function to return an empty string in that case.
It was not immediately clear from the possible call chains whether this
issue is currently actually triggerable or not.
Note that before commit 4843b4b5ec64 ("xhci: fix even more unsafe memory
usage in xhci tracing") the result effect in the failure case was different
as a static buffer was used here, but the code still worked incorrectly.
Fixes: 90d6d5731da7 ("xhci: Add tracing for input control context") Cc: stable@vger.kernel.org Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
commit 4843b4b5ec64 ("xhci: fix even more unsafe memory usage in xhci tracing") Link: https://lore.kernel.org/r/20220303110903.1662404-4-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit f6121a746fae18237395766f55123e6820be1e2e) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
xhci_reset() timeout was increased from 250ms to 10 seconds in order to
give Renesas 720201 xHC enough time to get ready in probe.
xhci_reset() is called with interrupts disabled in other places, and
waiting for 10 seconds there is not acceptable.
Add a timeout parameter to xhci_reset(), and adjust it back to 250ms
when called from xhci_stop() or xhci_shutdown() where interrupts are
disabled, and successful reset isn't that critical.
This solves issues when deactivating host mode on platforms like SM8450.
For now don't change the timeout if xHC is reset in xhci_resume().
No issues are reported for it, and we need the reset to succeed.
Locking around that reset needs to be revisited later.
Additionally change the signed integer timeout parameter in
xhci_handshake() to a u64 to match the timeout value we pass to
readl_poll_timeout_atomic()
A race between system resume and device-initiated resume may result in
runtime PM imbalance on USB2 root hub. If a device-initiated resume
starts and system resume xhci_bus_resume() directs U0 before hub driver
sees the resuming device in RESUME state, device-initiated resume will
not be finished in xhci_handle_usb2_port_link_resume(). In this case,
usb_hcd_end_port_resume() call is missing.
This changes calls usb_hcd_end_port_resume() if resuming device reaches
U0 to keep runtime PM balance.
Fixes: a231ec41e6f6 ("xhci: refactor U0 link state handling in get_port_status") Cc: stable@vger.kernel.org Signed-off-by: Henry Lin <henryl@nvidia.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20220303110903.1662404-5-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 4f2ab7e93b37874b9cbc7100e242941533cad820) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
xhci_decode_usbsts() is expected to return a zero-terminated string by
its only caller, xhci_stop_endpoint_command_watchdog(), which directly
logs the return value:
However, if no recognized bits are set in usbsts, the function will
return without having called any sprintf() and therefore return an
untouched non-zero-terminated caller-provided buffer, causing garbage
to be output to log.
Fix that by always including the raw value in the output.
Note that before commit 4843b4b5ec64 ("xhci: fix even more unsafe memory
usage in xhci tracing") the result effect in the failure case was different
as a static buffer was used here, but the code still worked incorrectly.
Fixes: 9c1aa36efdae ("xhci: Show host status when watchdog triggers and host is assumed dead.") Cc: stable@vger.kernel.org Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20220303110903.1662404-3-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 75bbc2b9748b51d230faafab73ba86fd76e326f1) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
The kernel test robot found a problem with the ene_ub6250 subdriver in
usb-storage: It uses structures containing bitfields to represent
hardware bits in its SD_STATUS, MS_STATUS, and SM_STATUS bytes. This
is not safe; it presumes a particular bit ordering and it assumes the
compiler will not insert padding, neither of which is guaranteed.
This patch fixes the problem by changing the structures to simple u8
values, with the bitfields replaced by bitmask constants.
In order to bring up the USB3 PHY on the Apple M1 we need to know the
orientation of the Type-C cable. Extract it from the status register and
forward it to the typec subsystem.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Sven Peter <sven@svenpeter.dev> Link: https://lore.kernel.org/r/20220226125912.59828-1-sven@svenpeter.dev Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit c94138ae40008327def5decc0aa3ac91c8e1ea12) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
The following sequence of operations results in a refcount warning:
1. Open device /dev/tpmrm.
2. Remove module tpm_tis_spi.
3. Write a TPM command to the file descriptor opened at step 1.
------------[ cut here ]------------
WARNING: CPU: 3 PID: 1161 at lib/refcount.c:25 kobject_get+0xa0/0xa4
refcount_t: addition on 0; use-after-free.
Modules linked in: tpm_tis_spi tpm_tis_core tpm mdio_bcm_unimac brcmfmac
sha256_generic libsha256 sha256_arm hci_uart btbcm bluetooth cfg80211 vc4
brcmutil ecdh_generic ecc snd_soc_core crc32_arm_ce libaes
raspberrypi_hwmon ac97_bus snd_pcm_dmaengine bcm2711_thermal snd_pcm
snd_timer genet snd phy_generic soundcore [last unloaded: spi_bcm2835]
CPU: 3 PID: 1161 Comm: hold_open Not tainted 5.10.0ls-main-dirty #2
Hardware name: BCM2711
[<c0410c3c>] (unwind_backtrace) from [<c040b580>] (show_stack+0x10/0x14)
[<c040b580>] (show_stack) from [<c1092174>] (dump_stack+0xc4/0xd8)
[<c1092174>] (dump_stack) from [<c0445a30>] (__warn+0x104/0x108)
[<c0445a30>] (__warn) from [<c0445aa8>] (warn_slowpath_fmt+0x74/0xb8)
[<c0445aa8>] (warn_slowpath_fmt) from [<c08435d0>] (kobject_get+0xa0/0xa4)
[<c08435d0>] (kobject_get) from [<bf0a715c>] (tpm_try_get_ops+0x14/0x54 [tpm])
[<bf0a715c>] (tpm_try_get_ops [tpm]) from [<bf0a7d6c>] (tpm_common_write+0x38/0x60 [tpm])
[<bf0a7d6c>] (tpm_common_write [tpm]) from [<c05a7ac0>] (vfs_write+0xc4/0x3c0)
[<c05a7ac0>] (vfs_write) from [<c05a7ee4>] (ksys_write+0x58/0xcc)
[<c05a7ee4>] (ksys_write) from [<c04001a0>] (ret_fast_syscall+0x0/0x4c)
Exception stack(0xc226bfa8 to 0xc226bff0)
bfa0: 00000000000105b400000003beafe6640000001400000000
bfc0: 00000000000105b4000103f8000000040000000000000000b6f9c000beafe684
bfe0: 0000006cbeafe6480001056cb6eb6944
---[ end trace d4b8409def9b8b1f ]---
The reason for this warning is the attempt to get the chip->dev reference
in tpm_common_write() although the reference counter is already zero.
Since commit 8979b02aaf1d ("tpm: Fix reference count to main device") the
extra reference used to prevent a premature zero counter is never taken,
because the required TPM_CHIP_FLAG_TPM2 flag is never set.
Fix this by moving the TPM 2 character device handling from
tpm_chip_alloc() to tpm_add_char_device() which is called at a later point
in time when the flag has been set in case of TPM2.
Commit fdc915f7f719 ("tpm: expose spaces via a device link /dev/tpmrm<n>")
already introduced function tpm_devs_release() to release the extra
reference but did not implement the required put on chip->devs that results
in the call of this function.
Fix this by putting chip->devs in tpm_chip_unregister().
Finally move the new implementation for the TPM 2 handling into a new
function to avoid multiple checks for the TPM_CHIP_FLAG_TPM2 flag in the
good case and error cases.
Cc: stable@vger.kernel.org Fixes: fdc915f7f719 ("tpm: expose spaces via a device link /dev/tpmrm<n>") Fixes: 8979b02aaf1d ("tpm: Fix reference count to main device") Co-developed-by: Jason Gunthorpe <jgg@ziepe.ca> Signed-off-by: Jason Gunthorpe <jgg@ziepe.ca> Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de> Tested-by: Stefan Berger <stefanb@linux.ibm.com> Reviewed-by: Jason Gunthorpe <jgg@nvidia.com> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 662893b4f6bd466ff9e1cd454c44c26d32d554fe) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
The block layer can't support a block size larger than
page size yet. And a block size that's too small or
not a power of two won't work either. If a misconfigured
device presents an invalid block size in configuration space,
it will result in the kernel crash something like below:
So let's use a block layer helper to validate the block size.
Signed-off-by: Xie Yongji <xieyongji@bytedance.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Link: https://lore.kernel.org/r/20211026144015.188-5-xieyongji@bytedance.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 5a0735b0bcf9eb8143136a660eb0e02b46d2007c) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
For various reasons based on the allocator behaviour and typical
use-cases at the time, when the max32_alloc_size optimisation was
introduced it seemed reasonable to couple the reset of the tracked
size to the update of cached32_node upon freeing a relevant IOVA.
However, since subsequent optimisations focused on helping genuine
32-bit devices make best use of even more limited address spaces, it
is now a lot more likely for cached32_node to be anywhere in a "full"
32-bit address space, and as such more likely for space to become
available from IOVAs below that node being freed.
At this point, the short-cut in __cached_rbnode_delete_update() really
doesn't hold up any more, and we need to fix the logic to reliably
provide the expected behaviour. We still want cached32_node to only move
upwards, but we should reset the allocation size if *any* 32-bit space
has become available.
We don't support runtime pm on APUs. They support more
dynamic power savings using clock and powergating.
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com> Tested-by: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit fe953e0f77e55d004a5b0c533262e389d01e3198) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
We need to set the APU flag from IP discovery before
we evaluate this code.
Acked-by: Evan Quan <evan.quan@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 0884abb259f180bc737cdb2c681d907b86f266e8) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
It was found that reading /proc/lockdep after a lockdep splat may
potentially cause an access to freed memory if lockdep_unregister_key()
is called after the splat but before access to /proc/lockdep [1]. This
is due to the fact that graph_lock() call in lockdep_unregister_key()
fails after the clearing of debug_locks by the splat process.
After lockdep_unregister_key() is called, the lock_name may be freed
but the corresponding lock_class structure still have a reference to
it. That invalid memory pointer will then be accessed when /proc/lockdep
is read by a user and a use-after-free (UAF) error will be reported if
KASAN is enabled.
To fix this problem, lockdep_unregister_key() is now modified to always
search for a matching key irrespective of the debug_locks state and
zap the corresponding lock class if a matching one is found.
Rework to add the header files to LOCAL_HDRS before including ../lib.mk,
since the dependency is evaluated in '$(OUTPUT)/%:%.c $(LOCAL_HDRS)' in
file lib.mk.
Link: https://lkml.kernel.org/r/20220304000645.1888133-1-yosryahmed@google.com Signed-off-by: Yosry Ahmed <yosryahmed@google.com> Cc: Shuah Khan <shuah@kernel.org> Cc: Nathan Chancellor <nathan@kernel.org> Cc: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit 9f93d46a63d58b6d72f87e95db90ca4422cb768b) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Add spi_device_id tables to avoid logs like "SPI driver ksz9477-switch
has no spi_device_id".
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit 2ea395dc132720da5232ca9182df8d3704cf2bcc) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Add __GFP_ZERO flag for compose_sadb_supported in function pfkey_register
to initialize the buffer of supp_skb to fix a kernel-info-leak issue.
1) Function pfkey_register calls compose_sadb_supported to request
a sk_buff. 2) compose_sadb_supported calls alloc_sbk to allocate
a sk_buff, but it doesn't zero it. 3) If auth_len is greater 0, then
compose_sadb_supported treats the memory as a struct sadb_supported and
begins to initialize. But it just initializes the field sadb_supported_len
and field sadb_supported_exttype without field sadb_supported_reserved.
Reported-by: TCS Robot <tcs_robot@tencent.com> Signed-off-by: Haimin Zhang <tcs_kernel@tencent.com> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit d06ee4572fd916fbb34d16dc81eb37d1dff83446) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
I observed the following problem with the BT404 touch pad
running the Phosh UI:
When e.g. typing on the virtual keyboard pressing "g" would
produce "ggg".
After some analysis it turns out the firmware reports that three
fingers hit that coordinate at the same time, finger 0, 2 and
4 (of the five available 0,1,2,3,4).
DOWN
Zinitix-TS 3-0020: finger 0 down (246, 395)
Zinitix-TS 3-0020: finger 1 up (0, 0)
Zinitix-TS 3-0020: finger 2 down (246, 395)
Zinitix-TS 3-0020: finger 3 up (0, 0)
Zinitix-TS 3-0020: finger 4 down (246, 395)
UP
Zinitix-TS 3-0020: finger 0 up (246, 395)
Zinitix-TS 3-0020: finger 2 up (246, 395)
Zinitix-TS 3-0020: finger 4 up (246, 395)
This is one touch and release: i.e. this is all reported on
touch (down) and release.
There is a field in the struct touch_event called finger_cnt
which is actually a bitmask of the fingers active in the
event.
Rename this field finger_mask as this matches the use contents
better, then use for_each_set_bit() to iterate over just the
fingers that are actally active.
Factor out a finger reporting function zinitix_report_fingers()
to handle all fingers.
Also be more careful in reporting finger down/up: we were
reporting every event with input_mt_report_slot_state(..., true);
but this should only be reported on finger down or move,
not on finger up, so also add code to check p->sub_status
to see what is happening and report correctly.
After this my Zinitix BT404 touchscreen report fingers
flawlessly.
The vendor drive I have notably does not use the "finger_cnt"
and contains obviously incorrect code like this:
if (touch_dev->touch_info.finger_cnt > MAX_SUPPORTED_FINGER_NUM)
touch_dev->touch_info.finger_cnt = MAX_SUPPORTED_FINGER_NUM;
As MAX_SUPPORTED_FINGER_NUM is an ordinal and the field is
a bitmask this seems quite confused.
While computing sgs in spi_map_buf(), the data type
used in min_t() for max_seg_size is 'unsigned int' where
as that of ctlr->max_dma_len is 'size_t'.
min_t(unsigned int,x,y) gives wrong results if one of x/y is
'size_t'
Consider the below examples on a 64-bit machine (ie size_t is
64-bits, and unsigned int is 32-bit).
case 1) min_t(unsigned int, 5, 0x100000001);
case 2) min_t(size_t, 5, 0x100000001);
Case 1 returns '1', where as case 2 returns '5'. As you can see
the result from case 1 is wrong.
This patch fixes the above issue by using the data type of the
parameters that are used in min_t with maximum data length.
Fixes: commit 1a4e53d2fc4f68aa ("spi: Fix invalid sgs value") Reported-by: Linus Torvalds <torvalds@linux-foundation.org> Suggested-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com> Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> Link: https://lore.kernel.org/r/20220316175317.465-1-biju.das.jz@bp.renesas.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit 8745973cdfc6a833d6d405d63760c9b92d78ff9e) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
This commit - while attempting to fix a regression - has caused a number
of other problems. As the fallout from it is more significant than the
initial problem itself, revert it for now before we find a correct
solution.
It is not recommened to use platform_get_resource(pdev, IORESOURCE_IRQ)
for requesting IRQ's resources any more, as they can be not ready yet in
case of DT-booting.
platform_get_irq() instead is a recommended way for getting IRQ even if
it was not retrieved earlier.
It also makes code simpler because we're getting "int" value right away
and no conversion from resource to int is required.
Reported-by: Zeal Robot <zealci@zte.com.cn> Signed-off-by: Minghao Chi (CGEL ZTE) <chi.minghao@zte.com.cn> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit 13b570f365b89fa2fd7840b92a4d5e924f26caec) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
max_seg_size is unsigned int and it can have a value up to 2^32
(for eg:-RZ_DMAC driver sets dma_set_max_seg_size as U32_MAX)
When this value is used in min_t() as an integer type, it becomes
-1 and the value of sgs becomes 0.
Fix this issue by replacing the 'int' data type with 'unsigned int'
in min_t().
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com> Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/r/20220307184843.9994-1-biju.das.jz@bp.renesas.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit 526a46a5f4795ed95d9ceedc634e7ac2493d24b7) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Some GPIO lines have stopped working after the patch
commit 2ab73c6d8323f ("gpio: Support GPIO controllers without pin-ranges")
And this has supposedly been fixed in the following patches
commit 89ad556b7f96a ("gpio: Avoid using pin ranges with !PINCTRL")
commit 6dbbf84603961 ("gpiolib: Don't free if pin ranges are not defined")
But an erratic behavior where some GPIO lines work while others do not work
has been introduced.
This patch reverts those changes so that the sysfs-gpio interface works
properly again.
Signed-off-by: Marcelo Roberto Jimenez <marcelo.jimenez@gmail.com> Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl> Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit a28571fcc422342c72d531ac4cc0991af98eb8eb) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
When the driver fails to register net device, it should free the DMA
region first, and then do other cleanup.
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit cd3121310e33a2584d7695206a656295d7d893d3) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Per VIRTIO v1.1 specification, section 5.1.3.1 Feature bit requirements:
"VIRTIO_NET_F_MQ Requires VIRTIO_NET_F_CTRL_VQ".
There's assumption in the mlx5_vdpa multiqueue code that MQ must come
together with CTRL_VQ. However, there's nowhere in the upper layer to
guarantee this assumption would hold. Were there an untrusted driver
sending down MQ without CTRL_VQ, it would compromise various spots for
e.g. is_index_valid() and is_ctrl_vq_idx(). Although this doesn't end
up with immediate panic or security loophole as of today's code, the
chance for this to be taken advantage of due to future code change is
not zero.
Harden the crispy assumption by failing the set_driver_features() call
when seeing (MQ && !CTRL_VQ). For that end, verify_min_features() is
renamed to verify_driver_features() to reflect the fact that it now does
more than just validate the minimum features. verify_driver_features()
is now used to accommodate various checks against the driver features
for set_driver_features().
A common pattern for device reset is currently:
vdev->config->reset(vdev);
.. cleanup ..
reset prevents new interrupts from arriving and waits for interrupt
handlers to finish.
However if - as is common - the handler queues a work request which is
flushed during the cleanup stage, we have code adding buffers / trying
to get buffers while device is reset. Not good.
This was reproduced by running
modprobe virtio_console
modprobe -r virtio_console
in a loop.
Fix this up by calling virtio_break_device + flush before reset.
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1786239 Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit 32aef620e650ca842f3fbf4cc6415b14714471ba) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
The mstar SoCs have an arch timer but HAVE_ARM_ARCH_TIMER wasn't
selected. If MSC313E_TIMER isn't selected then the kernel gets
stuck at boot because there are no timers available.
in tunnel mode, if outer interface(ipv4) is less, it is easily to let
inner IPV6 mtu be less than 1280. If so, a Packet Too Big ICMPV6 message
is received. When send again, packets are fragmentized with 1280, they
are still rejected with ICMPV6(Packet Too Big) by xfrmi_xmit2().
According to RFC4213 Section3.2.2:
if (IPv4 path MTU - 20) is less than 1280
if packet is larger than 1280 bytes
Send ICMPv6 "packet too big" with MTU=1280
Drop packet
else
Encapsulate but do not set the Don't Fragment
flag in the IPv4 header. The resulting IPv4
packet might be fragmented by the IPv4 layer
on the encapsulator or by some router along
the IPv4 path.
endif
else
if packet is larger than (IPv4 path MTU - 20)
Send ICMPv6 "packet too big" with
MTU = (IPv4 path MTU - 20).
Drop packet.
else
Encapsulate and set the Don't Fragment flag
in the IPv4 header.
endif
endif
Packets should be fragmentized with ipv4 outer interface, so change it.
After it is fragemtized with ipv4, there will be double fragmenation.
No.48 & No.51 are ipv6 fragment packets, No.48 is double fragmentized,
then tunneled with IPv4(No.49& No.50), which obey spec. And received peer
cannot decrypt it rightly.
As of logitech lightspeed receiver fw version 04.02.B0009,
HIDPP_PARAM_DEVICE_INFO is being reported as 0x11.
With patch "HID: logitech-dj: add support for the new lightspeed receiver
iteration", the mouse starts to error out with:
logitech-djreceiver: unusable device of type UNKNOWN (0x011) connected on
slot 1
and becomes unusable.
This has been noticed on a Logitech G Pro X Superlight fw MPM 25.01.B0018.
Signed-off-by: Lucas Zampieri <lzampier@redhat.com> Acked-by: Nestor Lopez Casado <nlopezcasad@logitech.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit a3248ecf072435549ae49e71647a1725be13d77c) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
The hyperv utilities use PTP clock interfaces and should depend a
a kconfig symbol such that they will be built as a loadable module or
builtin so that linker errors do not happen.
Prevents these build errors:
ld: drivers/hv/hv_util.o: in function `hv_timesync_deinit':
hv_util.c:(.text+0x37d): undefined reference to `ptp_clock_unregister'
ld: drivers/hv/hv_util.o: in function `hv_timesync_init':
hv_util.c:(.text+0x738): undefined reference to `ptp_clock_register'
Fixes: 3716a49a81ba ("hv_utils: implement Hyper-V PTP source") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Reported-by: kernel test robot <lkp@intel.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: "K. Y. Srinivasan" <kys@microsoft.com> Cc: Haiyang Zhang <haiyangz@microsoft.com> Cc: Stephen Hemminger <sthemmin@microsoft.com> Cc: Wei Liu <wei.liu@kernel.org> Cc: Dexuan Cui <decui@microsoft.com> Cc: linux-hyperv@vger.kernel.org Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Reviewed-by: Michael Kelley <mikelley@microsoft.com> Link: https://lore.kernel.org/r/20211126023316.25184-1-rdunlap@infradead.org Signed-off-by: Wei Liu <wei.liu@kernel.org> Cc: Petr Štetiar <ynezz@true.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit d5aad7d63b1b5c1f3c4b69e12c05e7c7d196fae8) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
The objcg is not cleared and put for kfence object when it is freed,
which could lead to memory leak for struct obj_cgroup and wrong
statistics of NR_SLAB_RECLAIMABLE_B or NR_SLAB_UNRECLAIMABLE_B.
Since the last freed object's objcg is not cleared,
mem_cgroup_from_obj() could return the wrong memcg when this kfence
object, which is not charged to any objcgs, is reallocated to other
users.
A real word issue [1] is caused by this bug.
Link: https://lore.kernel.org/all/000000000000cabcb505dae9e577@google.com/ Reported-by: syzbot+f8c45ccc7d5d45fc5965@syzkaller.appspotmail.com Fixes: d3fb45f370d9 ("mm, kfence: insert KFENCE hooks for SLAB") Signed-off-by: Muchun Song <songmuchun@bytedance.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Marco Elver <elver@google.com> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit dd84d71bcbcb2eb7f889449f6d4a3e65ae439e71) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
At least some PL2303GS have a bcdDevice of 0x605 instead of 0x100 as the
datasheet claims. Add it to the list of known release numbers for the
HXN (G) type.
Fixes: 894758d0571d ("USB: serial: pl2303: tighten type HXN (G) detection") Reported-by: Matyáš Kroupa <kroupa.matyas@gmail.com> Link: https://lore.kernel.org/r/165de6a0-43e9-092c-2916-66b115c7fbf4@gmail.com Cc: stable@vger.kernel.org # 5.13 Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 33325a62249e28066e9900a4ec3ee5bce75be6b4) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
IBM manufactures a PL2303 device for UPS communications. Add the vendor
and product IDs so that the PL2303 driver binds to the device.
Signed-off-by: Eddie James <eajames@linux.ibm.com> Signed-off-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Eddie James <eajames@linux.ibm.com> Link: https://lore.kernel.org/r/20220301224446.21236-1-eajames@linux.ibm.com Cc: stable@vger.kernel.org
[ johan: amend the SoB chain ] Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 2241e42f6c71b89eeab429e2d12521a9cb5c988d) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
ret = ath9k_hw_process_rxdesc_edma(ah, rs, skb->data);
if (ret == -EINPROGRESS) {
/*let device gain the buffer again*/
dma_sync_single_for_device(sc->dev, bf->bf_buf_addr,
common->rx_bufsize, DMA_FROM_DEVICE);
return false;
}
and it's worth noting how that first DMA sync:
dma_sync_single_for_cpu(..DMA_FROM_DEVICE);
is there to make sure the CPU can read the DMA buffer (possibly by
copying it from the bounce buffer area, or by doing some cache flush).
The iommu correctly turns that into a "copy from bounce bufer" so that
the driver can look at the state of the packets.
In the meantime, the device may continue to write to the DMA buffer, but
we at least have a snapshot of the state due to that first DMA sync.
But that _second_ DMA sync:
dma_sync_single_for_device(..DMA_FROM_DEVICE);
is telling the DMA mapping that the CPU wasn't interested in the area
because the packet wasn't there. In the case of a DMA bounce buffer,
that is a no-op.
Note how it's not a sync for the CPU (the "for_device()" part), and it's
not a sync for data written by the CPU (the "DMA_FROM_DEVICE" part).
Or rather, it _should_ be a no-op. That's what commit aa6f8dcbab47
broke: it made the code bounce the buffer unconditionally, and changed
the DMA_FROM_DEVICE to just unconditionally and illogically be
DMA_TO_DEVICE.
[ Side note: purely within the confines of the swiotlb driver it wasn't
entirely illogical: The reason it did that odd DMA_FROM_DEVICE ->
DMA_TO_DEVICE conversion thing is because inside the swiotlb driver,
it uses just a swiotlb_bounce() helper that doesn't care about the
whole distinction of who the sync is for - only which direction to
bounce.
So it took the "sync for device" to mean that the CPU must have been
the one writing, and thought it meant DMA_TO_DEVICE. ]
Also note how the commentary in that commit was wrong, probably due to
that whole confusion, claiming that the commit makes the swiotlb code
"bounce unconditionally (that is, also
when dir == DMA_TO_DEVICE) in order do avoid synchronising back stale
data from the swiotlb buffer"
which is nonsensical for two reasons:
- that "also when dir == DMA_TO_DEVICE" is nonsensical, as that was
exactly when it always did - and should do - the bounce.
- since this is a sync for the device (not for the CPU), we're clearly
fundamentally not coping back stale data from the bounce buffers at
all, because we'd be copying *to* the bounce buffers.
So that commit was just very confused. It confused the direction of the
synchronization (to the device, not the cpu) with the direction of the
DMA (from the device).
Reported-and-bisected-by: Oleksandr Natalenko <oleksandr@natalenko.name> Reported-by: Olha Cherevyk <olha.cherevyk@gmail.com> Cc: Halil Pasic <pasic@linux.ibm.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Kalle Valo <kvalo@kernel.org> Cc: Robin Murphy <robin.murphy@arm.com> Cc: Toke Høiland-Jørgensen <toke@toke.dk> Cc: Maxime Bizon <mbizon@freebox.fr> Cc: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 890f78e54b74f2e3f778bfd71d41a62cf893a9dd) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
My latest patch, attempting to fix the refcount leak in a minimal
way turned out to add a new bug.
Whenever the bind operation fails before we attempt to grab
a reference count on a device, we might release the device refcount
of a prior successful bind() operation.
syzbot was not happy about this [1].
Note to stable teams:
Make sure commit b37a46683739 ("netdevice: add the case if dev is NULL")
is already present in your trees.
The get_user()/put_user() functions are meant to check for
access_ok(), while the __get_user()/__put_user() functions
don't.
This broke in 4.19 for nds32, when it gained an extraneous
check in __get_user(), but lost the check it needs in
__put_user().
Fixes: 487913ab18c2 ("nds32: Extract the checking and getting pointer to a macro") Cc: stable@vger.kernel.org @ v4.19+ Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 22ac37c530656eedfeaa2536d7c65e4ff936b8ad) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
While most m68k platforms use separate address spaces for user
and kernel space, at least coldfire does not, and the other
ones have a TASK_SIZE that is less than the entire 4GB address
range.
Using the default implementation of __access_ok() stops coldfire
user space from trivially accessing kernel memory.
Reviewed-by: Christoph Hellwig <hch@lst.de> Cc: stable@vger.kernel.org Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 110dea31d48f9e91ce9ab528a82ac61470a27d14) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
exposure of the chip->tpm_mutex was removed from much of the upper
level code. In this conversion, tpm2_del_space() was missed. This
didn't matter much because it's usually called closely after a
converted operation, so there's only a very tiny race window where the
chip can be removed before the space flushing is done which causes a
NULL deref on the mutex. However, there are reports of this window
being hit in practice, so fix this by converting tpm2_del_space() to
use tpm_try_get_ops(), which performs all the teardown checks before
acquring the mutex.
Cc: stable@vger.kernel.org # 5.4.x Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 476ddd23f818fb94cf86fb5617f3bb9a7c92113d) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
While commit 6a01afcf8468 ("mac80211: mesh: Free ie data when leaving
mesh") fixed a memory leak on mesh leave / teardown it introduced a
potential memory corruption caused by a double free when rejoining the
mesh:
This double free / kernel panics can be reproduced by using wpa_supplicant
with an encrypted mesh (if set up without encryption via "iw" then
ifmsh->ie is always NULL, which avoids this issue). And then calling:
$ iw dev mesh0 mesh leave
$ iw dev mesh0 mesh join my-mesh
Note that typically these commands are not used / working when using
wpa_supplicant. And it seems that wpa_supplicant or wpa_cli are going
through a NETDEV_DOWN/NETDEV_UP cycle between a mesh leave and mesh join
where the NETDEV_UP resets the mesh.ie to NULL via a memcpy of
default_mesh_setup in cfg80211_netdev_notifier_call, which then avoids
the memory corruption, too.
The issue was first observed in an application which was not using
wpa_supplicant but "Senf" instead, which implements its own calls to
nl80211.
Fixing the issue by removing the kfree()'ing of the mesh IE in the mesh
join function and leaving it solely up to the mesh leave to free the
mesh IE.
Cc: stable@vger.kernel.org Fixes: 6a01afcf8468 ("mac80211: mesh: Free ie data when leaving mesh") Reported-by: Matthias Kretschmer <mathias.kretschmer@fit.fraunhofer.de> Signed-off-by: Linus Lüssing <ll@simonwunderlich.de> Tested-by: Mathias Kretschmer <mathias.kretschmer@fit.fraunhofer.de> Link: https://lore.kernel.org/r/20220310183513.28589-1-linus.luessing@c0d3.blue Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 12e407a8ef17623823fd0c066fbd7f103953d28d) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Three architectures check the end of a user access against the
address limit without taking a possible overflow into account.
Passing a negative length or another overflow in here returns
success when it should not.
Use the most common correct implementation here, which optimizes
for a constant 'size' argument, and turns the common case into a
single comparison.
Cc: stable@vger.kernel.org Fixes: da551281947c ("csky: User access") Fixes: f663b60f5215 ("microblaze: Fix uaccess_ok macro") Fixes: 7567746e1c0d ("Hexagon: Add user access functions") Reported-by: David Laight <David.Laight@aculab.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit e65d28d4e9bf90a35ba79c06661a572a38391dec) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Currently rcu_preempt_deferred_qs_irqrestore() releases rnp->boost_mtx
before reporting the expedited quiescent state. Under heavy real-time
load, this can result in this function being preempted before the
quiescent state is reported, which can in turn prevent the expedited grace
period from completing. Tim Murray reports that the resulting expedited
grace periods can take hundreds of milliseconds and even more than one
second, when they should normally complete in less than a millisecond.
This was fine given that there were no particular response-time
constraints for synchronize_rcu_expedited(), as it was designed
for throughput rather than latency. However, some users now need
sub-100-millisecond response-time constratints.
This patch therefore follows Neeraj's suggestion (seconded by Tim and
by Uladzislau Rezki) of simply reversing the two operations.
Reported-by: Tim Murray <timmurray@google.com> Reported-by: Joel Fernandes <joelaf@google.com> Reported-by: Neeraj Upadhyay <quic_neeraju@quicinc.com> Reviewed-by: Neeraj Upadhyay <quic_neeraju@quicinc.com> Reviewed-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Tested-by: Tim Murray <timmurray@google.com> Cc: Todd Kjos <tkjos@google.com> Cc: Sandeep Patil <sspatil@google.com> Cc: <stable@vger.kernel.org> # 5.4.x Signed-off-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 058d62a03e7d057d5eeec0db800117765ff23e6c) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
If virtio_gpu_object_shmem_init() fails (e.g. due to fault injection, as it
happened in the bug report by syzbot), virtio_gpu_array_put_free() could be
called with objs equal to NULL.
Ensure that objs is not NULL in virtio_gpu_array_put_free(), or otherwise
return from the function.
Cc: stable@vger.kernel.org # 5.13.x Signed-off-by: Roberto Sassu <roberto.sassu@huawei.com> Reported-by: syzbot+e9072e90624a31dfa85f@syzkaller.appspotmail.com Fixes: 377f8331d0565 ("drm/virtio: fix possible leak/unlock virtio_gpu_object_array") Link: http://patchwork.freedesktop.org/patch/msgid/20211213183122.838119-1-roberto.sassu@huawei.com Signed-off-by: Gerd Hoffmann <kraxel@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit b094fece3810c71ceee6f0921676cb65d4e68c5a) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
The implementations of aead and skcipher in the QAT driver do not
support properly requests with the CRYPTO_TFM_REQ_MAY_BACKLOG flag set.
If the HW queue is full, the driver returns -EBUSY but does not enqueue
the request.
This can result in applications like dm-crypt waiting indefinitely for a
completion of a request that was never submitted to the hardware.
To avoid this problem, disable the registration of all crypto algorithms
in the QAT driver by setting the number of crypto instances to 0 at
configuration time.
Cc: stable@vger.kernel.org Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit cb807cb52a8e399dfe7d58a64549cbbbb176ba9d) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Clevo NL5xRU and NL5xNU/TUXEDO Aura 15 Gen1 and Gen2 have both a working
native and video interface. However the default detection mechanism first
registers the video interface before unregistering it again and switching
to the native interface during boot. This results in a dangling SBIOS
request for backlight change for some reason, causing the backlight to
switch to ~2% once per boot on the first power cord connect or disconnect
event. Setting the native interface explicitly circumvents this buggy
behaviour by avoiding the unregistering process.
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com> Cc: All applicable <stable@vger.kernel.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 57a2b3f8bf1c91f4a7daf40cc77a095d8fc14493) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
For some reason, the Microsoft Surface Go 3 uses the standard ACPI
interface for battery information, but does not use the standard PNP0C0A
HID. Instead it uses MSHW0146 as identifier. Add that ID to the driver
as this seems to work well.
Additionally, the power state is not updated immediately after the AC
has been (un-)plugged, so add the respective quirk for that.
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com> Cc: All applicable <stable@vger.kernel.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit a01ac24114899d46dafcb0dc0c204418f9d28ea4) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
On this board the ACPI RSDP structure points to both a RSDT and an XSDT,
but the XSDT points to a truncated FADT. This causes all sorts of trouble
and usually a complete failure to boot after the following error occurs:
This leaves the ACPI implementation in such a broken state that subsequent
kernel subsystem initialisations go wrong, resulting in among others
mismapped PCI memory, SATA and USB enumeration failures, and freezes.
As this is an older embedded platform that will likely never see any BIOS
updates to address this issue and its default shipping OS only complies to
ACPI 1.0, work around this by forcing `acpi=rsdt`. This patch, applied on
top of Linux 5.10.102, was confirmed on real hardware to fix the issue.
Signed-off-by: Mark Cilissen <mark@yotsuba.nl> Cc: All applicable <stable@vger.kernel.org> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 8942aac690161dd3bd8c91044c6f867d9f10a364) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
All packets on ingress (except for jumbo) are terminated with a 4-bytes
CRC checksum. It's the responsability of the driver to strip those 4
bytes. Unfortunately a change dating back to March 2017 re-shuffled some
code and made the CRC stripping code effectively dead.
This change re-orders that part a bit such that the datalen is
immediately altered if needed.
Fixes: 4902a92270fb ("drivers: net: xgene: Add workaround for errata 10GE_8/ENET_11") Cc: stable@vger.kernel.org Signed-off-by: Stephane Graber <stgraber@ubuntu.com> Tested-by: Stephane Graber <stgraber@ubuntu.com> Link: https://lore.kernel.org/r/20220322224205.752795-1-stgraber@ubuntu.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 3e27eafac6590d09164e4ad00a2e99b30e4ea37e) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Tests 72 and 78 for ALSA in kselftest fail due to reading
inconsistent values from some devices on a VirtualBox
Virtual Machine using the snd_intel8x0 driver for the AC'97
Audio Controller device.
Taking for example test number 72, this is what the test reports:
"Surround Playback Volume.0 expected 1 but read 0, is_volatile 0"
"Surround Playback Volume.1 expected 0 but read 1, is_volatile 0"
These errors repeat for each value from 0 to 31.
Taking a look at these error messages it is possible to notice
that the written values are read back swapped.
When the write is performed, these values are initially stored in
an array used to sanity-check them and write them in the pcmreg
array. To write them, the two one-byte values are packed together
in a two-byte variable through bitwise operations: the first
value is shifted left by one byte and the second value is stored in the
right byte through a bitwise OR. When reading the values back,
right shifts are performed to retrieve the previously stored
bytes. These shifts are executed in the wrong order, thus
reporting the values swapped as shown above.
This patch fixes this mistake by reversing the read
operations' order.
Signed-off-by: Giacomo Guiduzzi <guiduzzi.giacomo@gmail.com> Signed-off-by: Paolo Valente <paolo.valente@linaro.org> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20220322200653.15862-1-guiduzzi.giacomo@gmail.com Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit c2052ad0c74fd0a1c6def7dd5a9bbad520f52687) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
For the RODE NT-USB the lowest Playback mixer volume setting mutes the
audio output. But it is not reported as such causing e.g. PulseAudio to
accidentally mute the device when selecting a low volume.
Fix this by applying the existing quirk for this kind of issue when the
device is detected.
snd_pcm_reset() is a non-atomic operation, and it's allowed to run
during the PCM stream running. It implies that the manipulation of
hw_ptr and other parameters might be racy.
This patch adds the PCM stream lock at appropriate places in
snd_pcm_*_reset() actions for covering that.
We have no protection against concurrent PCM buffer preallocation
changes via proc files, and it may potentially lead to UAF or some
weird problem. This patch applies the PCM open_mutex to the proc
write operation for avoiding the racy proc writes and the PCM stream
open (and further operations).
Like the previous fixes to hw_params and hw_free ioctl races, we need
to paper over the concurrent prepare ioctl calls against hw_params and
hw_free, too.
This patch implements the locking with the existing
runtime->buffer_mutex for prepare ioctls. Unlike the previous case
for snd_pcm_hw_hw_params() and snd_pcm_hw_free(), snd_pcm_prepare() is
performed to the linked streams, hence the lock can't be applied
simply on the top. For tracking the lock in each linked substream, we
modify snd_pcm_action_group() slightly and apply the buffer_mutex for
the case stream_lock=false (formerly there was no lock applied)
there.
In the current PCM design, the read/write syscalls (as well as the
equivalent ioctls) are allowed before the PCM stream is running, that
is, at PCM PREPARED state. Meanwhile, we also allow to re-issue
hw_params and hw_free ioctl calls at the PREPARED state that may
change or free the buffers, too. The problem is that there is no
protection against those mix-ups.
This patch applies the previously introduced runtime->buffer_mutex to
the read/write operations so that the concurrent hw_params or hw_free
call can no longer interfere during the operation. The mutex is
unlocked before scheduling, so we don't take it too long.
Currently we have neither proper check nor protection against the
concurrent calls of PCM hw_params and hw_free ioctls, which may result
in a UAF. Since the existing PCM stream lock can't be used for
protecting the whole ioctl operations, we need a new mutex to protect
those racy calls.
This patch introduced a new mutex, runtime->buffer_mutex, and applies
it to both hw_params and hw_free ioctl code paths. Along with it, the
both functions are slightly modified (the mmap_count check is moved
into the state-check block) for code simplicity.
Reported-by: Hu Jiahui <kirin.say@gmail.com> Cc: <stable@vger.kernel.org> Reviewed-by: Jaroslav Kysela <perex@perex.cz> Link: https://lore.kernel.org/r/20220322170720.3529-2-tiwai@suse.de Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 33061d0fba51d2bf70a2ef9645f703c33fe8e438) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
On a HP 288 Pro G8, the front mic could not be detected.In order to
get it working, the pin configuration needs to be set correctly, and
the ALC671_FIXUP_HP_HEADSET_MIC2 fixup needs to be applied.
New device id for Corsair Virtuoso SE RGB Wireless that currently is not
in the mixer_map. This entry in the mixer_map is necessary in order to
label its mixer appropriately and allow userspace to pick the correct
volume controls. For instance, my own Corsair Virtuoso SE RGB Wireless
headset has this new ID and consequently, the sidetone and volume are not
working correctly without this change.
> sudo lsusb -v | grep -i corsair
Bus 007 Device 011: ID 1b1c:0a40 Corsair CORSAIR VIRTUOSO SE Wireless Gam
idVendor 0x1b1c Corsair
iManufacturer 1 Corsair
iProduct 2 CORSAIR VIRTUOSO SE Wireless Gaming Headset
We've got syzbot reports hitting INT_MAX overflow at vmalloc()
allocation that is called from snd_pcm_plug_alloc(). Although we
apply the restrictions to input parameters, it's based only on the
hw_params of the underlying PCM device. Since the PCM OSS layer
allocates a temporary buffer for the data conversion, the size may
become unexpectedly large when more channels or higher rates is given;
in the reported case, it went over INT_MAX, hence it hits WARN_ON().
This patch is an attempt to avoid such an overflow and an allocation
for too large buffers. First off, it adds the limit of 1MB as the
upper bound for period bytes. This must be large enough for all use
cases, and we really don't want to handle a larger temporary buffer
than this size. The size check is performed at two places, where the
original period bytes is calculated and where the plugin buffer size
is calculated.
In addition, the driver uses array_size() and array3_size() for
multiplications to catch overflows for the converted period size and
buffer bytes.
This is essentially a revert of the commit dc865fb9e7c2 ("ASoC: sti:
Use snd_pcm_stop_xrun() helper"), which converted the manual
snd_pcm_stop() calls with snd_pcm_stop_xrun().
The commit above introduced a deadlock as snd_pcm_stop_xrun() itself
takes the PCM stream lock while the caller already holds it. Since
the conversion was done only for consistency reason and the open-call
with snd_pcm_stop() to the XRUN state is a correct usage, let's revert
the commit back as the fix.
Whenever llc_ui_bind() and/or llc_ui_autobind()
took a reference on a netdevice but subsequently fail,
they must properly release their reference
or risk the infamous message from unregister_netdevice()
at device dismantle.
unregister_netdevice: waiting for eth0 to become free. Usage count = 3
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: 赵子轩 <beraphin@gmail.com> Reported-by: Stoyan Manolov <smanolov@suse.de> Link: https://lore.kernel.org/r/20220323004147.1990845-1-eric.dumazet@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit e9072996108387ab19b497f5b557c93f98d96b0b) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
When an invalid (non existing) handle is used in a TPM command,
that uses the resource manager interface (/dev/tpmrm0) the resource
manager tries to load it from its internal cache, but fails and
the tpm_dev_transmit returns an -EINVAL error to the caller.
The existing async handler doesn't handle these error cases
currently and the condition in the poll handler never returns
mask with EPOLLIN set.
The result is that the poll call blocks and the application gets stuck
until the user_read_timer wakes it up after 120 sec.
Change the tpm_dev_async_work function to handle error conditions
returned from tpm_dev_transmit they are also reflected in the poll mask
and a correct error code could passed back to the caller.
Cc: Jarkko Sakkinen <jarkko@kernel.org> Cc: Jason Gunthorpe <jgg@ziepe.ca> Cc: <linux-integrity@vger.kernel.org> Cc: <stable@vger.kernel.org> Cc: <linux-kernel@vger.kernel.org> Fixes: 9e1b74a63f77 ("tpm: add support for nonblocking operation") Tested-by: Jarkko Sakkinen<jarkko@kernel.org> Signed-off-by: Tadeusz Struk <tstruk@gmail.com> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org> Cc: Tadeusz Struk <tadeusz.struk@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 42b9f6d19faa86ae74a35574b9db71cebae5cf10) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
After the recent changes made by commit c2e39305299f01 ("btrfs: clear
extent buffer uptodate when we fail to write it") and its followup fix,
commit 651740a5024117 ("btrfs: check WRITE_ERR when trying to read an
extent buffer"), we can now end up not cleaning up space reservations of
log tree extent buffers after a transaction abort happens, as well as not
cleaning up still dirty extent buffers.
This happens because if writeback for a log tree extent buffer failed,
then we have cleared the bit EXTENT_BUFFER_UPTODATE from the extent buffer
and we have also set the bit EXTENT_BUFFER_WRITE_ERR on it. Later on,
when trying to free the log tree with free_log_tree(), which iterates
over the tree, we can end up getting an -EIO error when trying to read
a node or a leaf, since read_extent_buffer_pages() returns -EIO if an
extent buffer does not have EXTENT_BUFFER_UPTODATE set and has the
EXTENT_BUFFER_WRITE_ERR bit set. Getting that -EIO means that we return
immediately as we can not iterate over the entire tree.
In that case we never update the reserved space for an extent buffer in
the respective block group and space_info object.
When this happens we get the following traces when unmounting the fs:
This also means that in case we have log tree extent buffers that are
still dirty, we can end up not cleaning them up in case we find an
extent buffer with EXTENT_BUFFER_WRITE_ERR set on it, as in that case
we have no way for iterating over the rest of the tree.
This issue is very often triggered with test cases generic/475 and
generic/648 from fstests.
The issue could almost be fixed by iterating over the io tree attached to
each log root which keeps tracks of the range of allocated extent buffers,
log_root->dirty_log_pages, however that does not work and has some
inconveniences:
1) After we sync the log, we clear the range of the extent buffers from
the io tree, so we can't find them after writeback. We could keep the
ranges in the io tree, with a separate bit to signal they represent
extent buffers already written, but that means we need to hold into
more memory until the transaction commits.
How much more memory is used depends a lot on whether we are able to
allocate contiguous extent buffers on disk (and how often) for a log
tree - if we are able to, then a single extent state record can
represent multiple extent buffers, otherwise we need multiple extent
state record structures to track each extent buffer.
In fact, my earlier approach did that:
However that can cause a very significant negative impact on
performance, not only due to the extra memory usage but also because
we get a larger and deeper dirty_log_pages io tree.
We got a report that, on beefy machines at least, we can get such
performance drop with fsmark for example:
2) We would be doing it only to deal with an unexpected and exceptional
case, which is basically failure to read an extent buffer from disk
due to IO failures. On a healthy system we don't expect transaction
aborts to happen after all;
3) Instead of relying on iterating the log tree or tracking the ranges
of extent buffers in the dirty_log_pages io tree, using the radix
tree that tracks extent buffers (fs_info->buffer_radix) to find all
log tree extent buffers is not reliable either, because after writeback
of an extent buffer it can be evicted from memory by the release page
callback of the btree inode (btree_releasepage()).
Since there's no way to be able to properly cleanup a log tree without
being able to read its extent buffers from disk and without using more
memory to track the logical ranges of the allocated extent buffers do
the following:
1) When we fail to cleanup a log tree, setup a flag that indicates that
failure;
2) Trigger writeback of all log tree extent buffers that are still dirty,
and wait for the writeback to complete. This is just to cleanup their
state, page states, page leaks, etc;
3) When unmounting the fs, ignore if the number of bytes reserved in a
block group and in a space_info is not 0 if, and only if, we failed to
cleanup a log tree. Also ignore only for metadata block groups and the
metadata space_info object.
This is far from a perfect solution, but it serves to silence test
failures such as those from generic/475 and generic/648. However having
a non-zero value for the reserved bytes counters on unmount after a
transaction abort, is not such a terrible thing and it's completely
harmless, it does not affect the filesystem integrity in any way.
Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Anand Jain <anand.jain@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 4c5d94990fa2fd609360ecd0f7e183212a7d115c) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Before this patch, the symbol end address fixup to be called, needed two
conditions being met:
if (prev->end == prev->start && prev->end != curr->start)
Where
"prev->end == prev->start" means that prev is zero-long
(and thus needs a fixup)
and
"prev->end != curr->start" means that fixup hasn't been applied yet
However, this logic is incorrect in the following situation:
In this case, prev->start == prev->end == curr->start == curr->end,
thus the condition above thinks that "we need a fixup due to zero
length of prev symbol, but it has been probably done, since the
prev->end == curr->start", which is wrong.
After the patch, the execution path proceeds to arch__symbols__fixup_end
function which fixes up the size of prev symbol by adding page_size to
its end offset.
Fixes: 3b01a413c196c910 ("perf symbols: Improve kallsyms symbol end addr calculation") Signed-off-by: Michael Petlan <mpetlan@redhat.com> Cc: Athira Jajeev <atrajeev@linux.vnet.ibm.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Kajol Jain <kjain@linux.ibm.com> Cc: Madhavan Srinivasan <maddy@linux.ibm.com> Link: http://lore.kernel.org/lkml/20220317135536.805-1-mpetlan@redhat.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 23775775b9a66b2ea1bb4873282998351f928c3e) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Syzbot reported warning in usb_submit_urb() which is caused by wrong
endpoint type. There was a check for the number of endpoints, but not
for the type of endpoint.
Fix it by replacing old desc.bNumEndpoints check with
usb_find_common_endpoints() helper for finding endpoints
Fail log:
usb 5-1: BOGUS urb xfer, pipe 1 != type 3
WARNING: CPU: 2 PID: 48 at drivers/usb/core/urb.c:502 usb_submit_urb+0xed2/0x18a0 drivers/usb/core/urb.c:502
Modules linked in:
CPU: 2 PID: 48 Comm: kworker/2:2 Not tainted 5.17.0-rc6-syzkaller-00226-g07ebd38a0da2 #0
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.14.0-2 04/01/2014
Workqueue: usb_hub_wq hub_event
...
Call Trace:
<TASK>
aiptek_open+0xd5/0x130 drivers/input/tablet/aiptek.c:830
input_open_device+0x1bb/0x320 drivers/input/input.c:629
kbd_connect+0xfe/0x160 drivers/tty/vt/keyboard.c:1593
Fixes: 8e20cf2bce12 ("Input: aiptek - fix crash on detecting device without endpoints") Reported-and-tested-by: syzbot+75cccf2b7da87fb6f84b@syzkaller.appspotmail.com Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Link: https://lore.kernel.org/r/20220308194328.26220-1-paskripkin@gmail.com Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit e762f57ff255af28236cd02ca9fc5c7e5a089d31) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
This is caused by mpt3sas_base_sync_reply_irqs() using an invalid reply_q
pointer outside of the list_for_each_entry() loop. At the end of the full
list traversal the pointer is invalid.
Move the _base_process_reply_queue() call inside of the loop.
Link: https://lore.kernel.org/r/d625deae-a958-0ace-2ba3-0888dd0a415b@ddn.com Fixes: 711a923c14d9 ("scsi: mpt3sas: Postprocessing of target and LUN reset") Cc: stable@vger.kernel.org Acked-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com> Signed-off-by: Matt Lupfer <mlupfer@ddn.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 0cd2dd4bcf4abc812148c4943f966a3c8dccb00f) Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
projects / mirror_ubuntu-jammy-kernel.git / log