Eric Anholt [Thu, 8 Feb 2018 13:54:05 +0000 (14:54 +0100)]
i2c: bcm2835: Set up the rising/falling edge delays
We were leaving them in the power on state (or the state the firmware
had set up for some client, if we were taking over from them). The
boot state was 30 core clocks, when we actually want to sample some
time after (to make sure that the new input bit has actually arrived).
Signed-off-by: Eric Anholt <eric@anholt.net> Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Cc: stable@kernel.org
Jarkko Nikula [Fri, 16 Feb 2018 09:24:29 +0000 (11:24 +0200)]
i2c: i801: Add missing documentation entries for Braswell and Kaby Lake
Commits adding PCI IDs for Intel Braswell and Kaby Lake PCH-H lacked the
respective Kconfig and Documentation/i2c/busses/i2c-i801 change. Add
them now.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Ben Gardner [Wed, 14 Feb 2018 15:29:52 +0000 (09:29 -0600)]
i2c: designware: must wait for enable
One I2C bus on my Atom E3845 board has been broken since 4.9.
It has two devices, both declared by ACPI and with built-in drivers.
There are two back-to-back transactions originating from the kernel, one
targeting each device. The first transaction works, the second one locks
up the I2C controller. The controller never recovers.
These kernel logs show up whenever an I2C transaction is attempted after
this failure.
i2c-designware-pci 0000:00:18.3: timeout in disabling adapter
i2c-designware-pci 0000:00:18.3: timeout waiting for bus ready
Waiting for the I2C controller status to indicate that it is enabled
before programming it fixes the issue.
I have tested this patch on 4.14 and 4.15.
Fixes: commit 2702ea7dbec5 ("i2c: designware: wait for disable/enable only if necessary") Cc: linux-stable <stable@vger.kernel.org> #4.13+ Signed-off-by: Ben Gardner <gardner.ben@gmail.com> Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Reviewed-by: José Roberto de Souza <jose.souza@intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Linus Torvalds [Sun, 18 Feb 2018 20:56:41 +0000 (12:56 -0800)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 Kconfig fixes from Thomas Gleixner:
"Three patchlets to correct HIGHMEM64G and CMPXCHG64 dependencies in
Kconfig when CPU selections are explicitely set to M586 or M686"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/Kconfig: Explicitly enumerate i686-class CPUs in Kconfig
x86/Kconfig: Exclude i586-class CPUs lacking PAE support from the HIGHMEM64G Kconfig group
x86/Kconfig: Add missing i586-class CPUs to the X86_CMPXCHG64 Kconfig group
Linus Torvalds [Sun, 18 Feb 2018 20:38:40 +0000 (12:38 -0800)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf updates from Thomas Gleixner:
"Perf tool updates and kprobe fixes:
- perf_mmap overwrite mode fixes/overhaul, prep work to get 'perf
top' using it, making it bearable to use it in large core count
systems such as Knights Landing/Mill Intel systems (Kan Liang)
- s/390 now uses syscall.tbl, just like x86-64 to generate the
syscall table id -> string tables used by 'perf trace' (Hendrik
Brueckner)
- Use strtoull() instead of home grown function (Andy Shevchenko)
- Synchronize kernel ABI headers, v4.16-rc1 (Ingo Molnar)
- Document missing 'perf data --force' option (Sangwon Hong)
- Add perf vendor JSON metrics for ARM Cortex-A53 Processor (William
Cohen)
- Improve error handling and error propagation of ftrace based
kprobes so failures when installing kprobes are not silently
ignored and create disfunctional tracepoints"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits)
kprobes: Propagate error from disarm_kprobe_ftrace()
kprobes: Propagate error from arm_kprobe_ftrace()
Revert "tools include s390: Grab a copy of arch/s390/include/uapi/asm/unistd.h"
perf s390: Rework system call table creation by using syscall.tbl
perf s390: Grab a copy of arch/s390/kernel/syscall/syscall.tbl
tools/headers: Synchronize kernel ABI headers, v4.16-rc1
perf test: Fix test trace+probe_libc_inet_pton.sh for s390x
perf data: Document missing --force option
perf tools: Substitute yet another strtoull()
perf top: Check the latency of perf_top__mmap_read()
perf top: Switch default mode to overwrite mode
perf top: Remove lost events checking
perf hists browser: Add parameter to disable lost event warning
perf top: Add overwrite fall back
perf evsel: Expose the perf_missing_features struct
perf top: Check per-event overwrite term
perf mmap: Discard legacy interface for mmap read
perf test: Update mmap read functions for backward-ring-buffer test
perf mmap: Introduce perf_mmap__read_event()
perf mmap: Introduce perf_mmap__read_done()
...
Linus Torvalds [Sat, 17 Feb 2018 18:20:47 +0000 (10:20 -0800)]
Merge tag 'for-linus-20180217' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
- NVMe pull request from Keith, with fixes all over the map for nvme.
From various folks.
- Classic polling fix, that avoids a latency issue where we still end
up waiting for an interrupt in some cases. From Nitesh Shetty.
- Comment typo fix from Minwoo Im.
* tag 'for-linus-20180217' of git://git.kernel.dk/linux-block:
block: fix a typo in comment of BLK_MQ_POLL_STATS_BKTS
nvme-rdma: fix sysfs invoked reset_ctrl error flow
nvmet: Change return code of discard command if not supported
nvme-pci: Fix timeouts in connecting state
nvme-pci: Remap CMB SQ entries on every controller reset
nvme: fix the deadlock in nvme_update_formats
blk: optimization for classic polling
nvme: Don't use a stack buffer for keep-alive command
nvme_fc: cleanup io completion
nvme_fc: correct abort race condition on resets
nvme: Fix discard buffer overrun
nvme: delete NVME_CTRL_LIVE --> NVME_CTRL_CONNECTING transition
nvme-rdma: use NVME_CTRL_CONNECTING state to mark init process
nvme: rename NVME_CTRL_RECONNECTING state to NVME_CTRL_CONNECTING
Linus Torvalds [Sat, 17 Feb 2018 18:08:28 +0000 (10:08 -0800)]
Merge tag 'mmc-v4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
- meson-gx: Revert to earlier tuning process
- bcm2835: Don't overwrite max frequency unconditionally
* tag 'mmc-v4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: bcm2835: Don't overwrite max frequency unconditionally
Revert "mmc: meson-gx: include tx phase in the tuning process"
Linus Torvalds [Sat, 17 Feb 2018 18:06:13 +0000 (10:06 -0800)]
Merge tag 'mtd/fixes-for-4.16-rc2' of git://git.infradead.org/linux-mtd
Pull mtd fixes from Boris Brezillon:
- add missing dependency to NAND_MARVELL Kconfig entry
- use the appropriate OOB layout in the VF610 driver
* tag 'mtd/fixes-for-4.16-rc2' of git://git.infradead.org/linux-mtd:
mtd: nand: MTD_NAND_MARVELL should depend on HAS_DMA
mtd: nand: vf610: set correct ooblayout
Linus Torvalds [Sat, 17 Feb 2018 17:48:26 +0000 (09:48 -0800)]
Merge tag 'powerpc-4.16-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"The main attraction is a fix for a bug in the new drmem code, which
was causing an oops on boot on some versions of Qemu.
There's also a fix for XIVE (Power9 interrupt controller) on KVM, as
well as a few other minor fixes.
Thanks to: Corentin Labbe, Cyril Bur, Cédric Le Goater, Daniel Black,
Nathan Fontenot, Nicholas Piggin"
* tag 'powerpc-4.16-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/pseries: Check for zero filled ibm,dynamic-memory property
powerpc/pseries: Add empty update_numa_cpu_lookup_table() for NUMA=n
powerpc/powernv: IMC fix out of bounds memory access at shutdown
powerpc/xive: Use hw CPU ids when configuring the CPU queues
powerpc: Expose TSCR via sysfs only on powernv
Linus Torvalds [Sat, 17 Feb 2018 17:46:18 +0000 (09:46 -0800)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
"The bulk of this is the pte accessors annotation to READ/WRITE_ONCE
(we tried to avoid pushing this during the merge window to avoid
conflicts)
- Updated the page table accessors to use READ/WRITE_ONCE and prevent
compiler transformation that could lead to an apparent loss of
coherency
- Enabled branch predictor hardening for the Falkor CPU
- Fix interaction between kpti enabling and KASan causing the
recursive page table walking to take a significant time
- Fix some sparse warnings"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: cputype: Silence Sparse warnings
arm64: mm: Use READ_ONCE/WRITE_ONCE when accessing page tables
arm64: proc: Set PTE_NG for table entries to avoid traversing them twice
arm64: Add missing Falkor part number for branch predictor hardening
Linus Torvalds [Sat, 17 Feb 2018 17:16:09 +0000 (09:16 -0800)]
Merge tag 'for-linus-4.16a-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
- fixes for the Xen pvcalls frontend driver
- fix for booting Xen pv domains
- fix for the xenbus driver user interface
* tag 'for-linus-4.16a-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
pvcalls-front: wait for other operations to return when release passive sockets
pvcalls-front: introduce a per sock_mapping refcount
x86/xen: Calculate __max_logical_packages on PV domains
xenbus: track caller request id
pvcalls-front: introduce a per sock_mapping refcount
Introduce a per sock_mapping refcount, in addition to the existing
global refcount. Thanks to the sock_mapping refcount, we can safely wait
for it to be 1 in pvcalls_front_release before freeing an active socket,
instead of waiting for the global refcount to be 1.
Joao Martins [Fri, 2 Feb 2018 17:42:33 +0000 (17:42 +0000)]
xenbus: track caller request id
Commit fd8aa9095a95 ("xen: optimize xenbus driver for multiple concurrent
xenstore accesses") optimized xenbus concurrent accesses but in doing so
broke UABI of /dev/xen/xenbus. Through /dev/xen/xenbus applications are in
charge of xenbus message exchange with the correct header and body. Now,
after the mentioned commit the replies received by application will no
longer have the header req_id echoed back as it was on request (see
specification below for reference), because that particular field is being
overwritten by kernel.
struct xsd_sockmsg
{
uint32_t type; /* XS_??? */
uint32_t req_id;/* Request identifier, echoed in daemon's response. */
uint32_t tx_id; /* Transaction id (0 if not related to a transaction). */
uint32_t len; /* Length of data following this. */
/* Generally followed by nul-terminated string(s). */
};
Before there was only one request at a time so req_id could simply be
forwarded back and forth. To allow simultaneous requests we need a
different req_id for each message thus kernel keeps a monotonic increasing
counter for this field and is written on every request irrespective of
userspace value.
Forwarding again the req_id on userspace requests is not a solution because
we would open the possibility of userspace-generated req_id colliding with
kernel ones. So this patch instead takes another route which is to
artificially keep user req_id while keeping the xenbus logic as is. We do
that by saving the original req_id before xs_send(), use the private kernel
counter as req_id and then once reply comes and was validated, we restore
back the original req_id.
Robin Murphy [Fri, 16 Feb 2018 17:04:23 +0000 (17:04 +0000)]
arm64: cputype: Silence Sparse warnings
Sparse makes a fair bit of noise about our MPIDR mask being implicitly
long - let's explicitly describe it as such rather than just relying on
the value forcing automatic promotion.
Signed-off-by: Robin Murphy <robin.murphy@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Linus Torvalds [Fri, 16 Feb 2018 20:22:33 +0000 (12:22 -0800)]
Merge tag 'dma-mapping-4.16-2' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping fixes from Christoph Hellwig:
"A few dma-mapping fixes for the fallout from the changes in rc1"
* tag 'dma-mapping-4.16-2' of git://git.infradead.org/users/hch/dma-mapping:
powerpc/macio: set a proper dma_coherent_mask
dma-mapping: fix a comment typo
dma-direct: comment the dma_direct_free calling convention
dma-direct: mark as is_phys
ia64: fix build failure with CONFIG_SWIOTLB
Will Deacon [Thu, 15 Feb 2018 11:14:56 +0000 (11:14 +0000)]
arm64: mm: Use READ_ONCE/WRITE_ONCE when accessing page tables
In many cases, page tables can be accessed concurrently by either another
CPU (due to things like fast gup) or by the hardware page table walker
itself, which may set access/dirty bits. In such cases, it is important
to use READ_ONCE/WRITE_ONCE when accessing page table entries so that
entries cannot be torn, merged or subject to apparent loss of coherence
due to compiler transformations.
Whilst there are some scenarios where this cannot happen (e.g. pinned
kernel mappings for the linear region), the overhead of using READ_ONCE
/WRITE_ONCE everywhere is minimal and makes the code an awful lot easier
to reason about. This patch consistently uses these macros in the arch
code, as well as explicitly namespacing pointers to page table entries
from the entries themselves by using adopting a 'p' suffix for the former
(as is sometimes used elsewhere in the kernel source).
Tested-by: Yury Norov <ynorov@caviumnetworks.com> Tested-by: Richard Ruigrok <rruigrok@codeaurora.org> Reviewed-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Linus Torvalds [Fri, 16 Feb 2018 17:26:18 +0000 (09:26 -0800)]
Merge tag 'for-4.16-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"We have a few assorted fixes, some of them show up during fstests so I
gave them more testing"
* tag 'for-4.16-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: Fix use-after-free when cleaning up fs_devs with a single stale device
Btrfs: fix null pointer dereference when replacing missing device
btrfs: remove spurious WARN_ON(ref->count < 0) in find_parent_nodes
btrfs: Ignore errors from btrfs_qgroup_trace_extent_post
Btrfs: fix unexpected -EEXIST when creating new inode
Btrfs: fix use-after-free on root->orphan_block_rsv
Btrfs: fix btrfs_evict_inode to handle abnormal inodes correctly
Btrfs: fix extent state leak from tree log
Btrfs: fix crash due to not cleaning up tree log block's dirty bits
Btrfs: fix deadlock in run_delalloc_nocow
Linus Torvalds [Fri, 16 Feb 2018 17:23:36 +0000 (09:23 -0800)]
Merge tag 'for-4.16/dm-chained-bios-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fix from Mike Snitzer:
"Fix for DM core to properly propagate errors (avoids overriding
non-zero error with 0). This is particularly important given DM core's
increased use of chained bios"
* tag 'for-4.16/dm-chained-bios-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm: correctly handle chained bios in dec_pending()
Linus Torvalds [Fri, 16 Feb 2018 17:20:00 +0000 (09:20 -0800)]
Merge tag 'platform-drivers-x86-v4.16-4' of git://git.infradead.org/linux-platform-drivers-x86
Pull x86 platform driver fixes from Andy Shevchenko:
- regression fix in keyboard support for Dell laptops
- prevent out-of-boundary write in WMI bus driver
- increase timeout to read functional key status on Lenovo laptops
* tag 'platform-drivers-x86-v4.16-4' of git://git.infradead.org/linux-platform-drivers-x86:
platform/x86: dell-laptop: Removed duplicates in DMI whitelist
platform/x86: dell-laptop: fix kbd_get_state's request value
platform/x86: ideapad-laptop: Increase timeout to wait for EC answer
platform/x86: wmi: fix off-by-one write in wmi_dev_probe()
Linus Torvalds [Fri, 16 Feb 2018 17:11:30 +0000 (09:11 -0800)]
Merge tag 'sound-4.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A collection of usual suspects:
- a handful USB-audio and HD-audio device-specific quirks
- some trivial fixes for the new AC97 bus stuff
- another race fix in ALSA sequencer core"
* tag 'sound-4.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/realtek: PCI quirk for Fujitsu U7x7
ALSA: seq: Fix racy pool initializations
ALSA: usb: add more device quirks for USB DSD devices
ALSA: usb-audio: Fix UAC2 get_ctl request with a RANGE attribute
ALSA: ac97: Fix copy and paste typo in documentation
ALSA: usb-audio: add implicit fb quirk for Behringer UFX1204
ALSA: ac97: kconfig: Remove select of undefined symbol AC97
ALSA: hda/realtek - Enable Thinkpad Dock device for ALC298 platform
ALSA: hda/realtek - Add headset mode support for Dell laptop
ALSA: hda - Fix headset mic detection problem for two Dell machines
Linus Torvalds [Fri, 16 Feb 2018 17:08:59 +0000 (09:08 -0800)]
Merge tag 'drm-fixes-for-v4.16-rc2' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"One nouveau regression fix, one AMD quirk and a full set of i915
fixes.
The i915 fixes are mostly for things caught by their CI system, main
ones being DSI panel fixes and GEM fixes"
* tag 'drm-fixes-for-v4.16-rc2' of git://people.freedesktop.org/~airlied/linux:
drm/nouveau: Make clock gate support conditional
drm/i915: Fix DSI panels with v1 MIPI sequences without a DEASSERT sequence v3
drm/i915: Free memdup-ed DSI VBT data structures on driver_unload
drm/i915: Add intel_bios_cleanup() function
drm/i915/vlv: Add cdclk workaround for DSI
drm/i915/gvt: fix one typo of render_mmio trace
drm/i915/gvt: Support BAR0 8-byte reads/writes
drm/i915/gvt: add 0xe4f0 into gen9 render list
drm/i915/pmu: Fix building without CONFIG_PM
drm/i915/pmu: Fix sleep under atomic in RC6 readout
drm/i915/pmu: Fix PMU enable vs execlists tasklet race
drm/i915: Lock out execlist tasklet while peeking inside for busy-stats
drm/i915/breadcrumbs: Ignore unsubmitted signalers
drm/i915: Don't wake the device up to check if the engine is asleep
drm/i915: Avoid truncation before clamping userspace's priority value
drm/i915/perf: Fix compiler warning for string truncation
drm/i915/perf: Fix compiler warning for string truncation
drm/amdgpu: add new device to use atpx quirk
NeilBrown [Thu, 15 Feb 2018 09:00:15 +0000 (20:00 +1100)]
dm: correctly handle chained bios in dec_pending()
dec_pending() is given an error status (possibly 0) to be recorded
against a bio. It can be called several times on the one 'struct
dm_io', and it is careful to only assign a non-zero error to
io->status. However when it then assigned io->status to bio->bi_status,
it is not careful and could overwrite a genuine error status with 0.
This can happen when chained bios are in use. If a bio is chained
beneath the bio that this dm_io is handling, the child bio might
complete and set bio->bi_status before the dm_io completes.
This has been possible since chained bios were introduced in 3.14, and
has become a lot easier to trigger with commit 18a25da84354 ("dm: ensure
bio submission follows a depth-first tree walk") as that commit caused
dm to start using chained bios itself.
A particular failure mode is that if a bio spans an 'error' target and a
working target, the 'error' fragment will complete instantly and set the
->bi_status, and the other fragment will normally complete a little
later, and will clear ->bi_status.
The fix is simply to only assign io_error to bio->bi_status when
io_error is not zero.
Reported-and-tested-by: Milan Broz <gmazyland@gmail.com> Cc: stable@vger.kernel.org (v3.14+) Signed-off-by: NeilBrown <neilb@suse.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Thomas Gleixner [Fri, 16 Feb 2018 14:47:26 +0000 (15:47 +0100)]
Merge tag 'irqchip-4.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/urgent
Pull irqchip updates for 4.16-rc2 from Marc Zyngier
- A MIPS GIC fix for spurious, masked interrupts
- A fix for a subtle IPI bug in GICv3
- Do not probe GICv3 ITSs that are marked as disabled
- Multi-MSI support for GICv2m
- Various cleanups
Jaedon Shin [Mon, 12 Feb 2018 02:18:12 +0000 (11:18 +0900)]
irqchip/bcm: Remove hashed address printing
Since commit ad67b74d2469 ("printk: hash addresses printed with %p")
pointers are being hashed when printed. Displaying the virtual memory at
bootup time is not helpful. so delete the prints.
Marc Zyngier [Tue, 6 Feb 2018 18:55:33 +0000 (18:55 +0000)]
irqchip/gic-v2m: Add PCI Multi-MSI support
We'd never implemented Multi-MSI support with GICv2m, because
it is weird and clunky, and you'd think people would rather use
MSI-X.
Turns out there is still plenty of devices out there that rely
on Multi-MSI. Oh well, let's teach that trick to the v2m widget,
it is not a big deal anyway.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Stephen Boyd [Thu, 1 Feb 2018 17:03:29 +0000 (09:03 -0800)]
irqchip/gic-v3: Ignore disabled ITS nodes
On some platforms there's an ITS available but it's not enabled
because reading or writing the registers is denied by the
firmware. In fact, reading or writing them will cause the system
to reset. We could remove the node from DT in such a case, but
it's better to skip nodes that are marked as "disabled" in DT so
that we can describe the hardware that exists and use the status
property to indicate how the firmware has configured things.
Cc: Stuart Yoder <stuyoder@gmail.com> Cc: Laurentiu Tudor <laurentiu.tudor@nxp.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Rajendra Nayak <rnayak@codeaurora.org> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
irqchip/gic-v3: Use wmb() instead of smb_wmb() in gic_raise_softirq()
A DMB instruction can be used to ensure the relative order of only
memory accesses before and after the barrier. Since writes to system
registers are not memory operations, barrier DMB is not sufficient
for observability of memory accesses that occur before ICC_SGI1R_EL1
writes.
A DSB instruction ensures that no instructions that appear in program
order after the DSB instruction, can execute until the DSB instruction
has completed.
Cc: stable@vger.kernel.org Acked-by: Will Deacon <will.deacon@arm.com>, Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This could be fixed with printk_deferred() but that might lessen its
usefulness for debugging. So change it to pr_devel to keep it out of
production kernels. Developers working on gic-v3 can enable it as
needed in their kernels.
Signed-off-by: Mark Salter <msalter@redhat.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Commit 7778c4b27cbe ("irqchip: mips-gic: Use pcpu_masks to avoid reading
GIC_SH_MASK*") removed the read of the hardware mask register when
handling shared interrupts, instead using the driver's shadow pcpu_masks
entry as the effective mask. Unfortunately this did not take account of
the write to pcpu_masks during gic_shared_irq_domain_map, which
effectively unmasks the interrupt early. If an interrupt is asserted,
gic_handle_shared_int decodes and processes the interrupt even though it
has not yet been unmasked via gic_unmask_irq, which also sets the
appropriate bit in pcpu_masks.
On the MIPS Boston board, when a console command line of
"console=ttyS0,115200n8r" is passed, the modem status IRQ is enabled in
the UART, which is immediately raised to the GIC. The interrupt has been
mapped, but no handler has yet been registered, nor is it expected to be
unmasked. However, the write to pcpu_masks in gic_shared_irq_domain_map
has effectively unmasked it, resulting in endless reports of:
To fix this, just remove the write to pcpu_masks in
gic_shared_irq_domain_map. The existing write in gic_unmask_irq is the
correct place for what is now the effective unmasking.
Cc: stable@vger.kernel.org Fixes: 7778c4b27cbe ("irqchip: mips-gic: Use pcpu_masks to avoid reading GIC_SH_MASK*") Signed-off-by: Matt Redfearn <matt.redfearn@mips.com> Reviewed-by: Paul Burton <paul.burton@mips.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Nathan Fontenot [Fri, 16 Feb 2018 03:27:41 +0000 (21:27 -0600)]
powerpc/pseries: Check for zero filled ibm,dynamic-memory property
Some versions of QEMU will produce an ibm,dynamic-reconfiguration-memory
node with a ibm,dynamic-memory property that is zero-filled. This
causes the drmem code to oops trying to parse this property.
The fix for this is to validate that the property does contain LMB
entries before trying to parse it and bail if the count is zero.
Oops: Kernel access of bad area, sig: 11 [#1]
DAR: 0000000000000010
NIP read_drconf_v1_cell+0x54/0x9c
LR read_drconf_v1_cell+0x48/0x9c
Call Trace:
__param_initcall_debug+0x0/0x28 (unreliable)
drmem_init+0x144/0x2f8
do_one_initcall+0x64/0x1d0
kernel_init_freeable+0x298/0x38c
kernel_init+0x24/0x160
ret_from_kernel_thread+0x5c/0xb4
The ibm,dynamic-reconfiguration-memory device tree property generated
that causes this:
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com> Reviewed-by: Cyril Bur <cyrilbur@gmail.com> Tested-by: Daniel Black <daniel@linux.vnet.ibm.com>
[mpe: Trim oops report] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Michael Kelley [Wed, 14 Feb 2018 02:54:03 +0000 (02:54 +0000)]
cpumask: Make for_each_cpu_wrap() available on UP as well
for_each_cpu_wrap() was originally added in the #else half of a
large "#if NR_CPUS == 1" statement, but was omitted in the #if
half. This patch adds the missing #if half to prevent compile
errors when NR_CPUS is 1.
Reported-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: Michael Kelley <mhkelley@outlook.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: kys@microsoft.com Cc: martin.petersen@oracle.com Cc: mikelley@microsoft.com Fixes: c743f0a5c50f ("sched/fair, cpumask: Export for_each_cpu_wrap()") Link: http://lkml.kernel.org/r/SN6PR1901MB2045F087F59450507D4FCC17CBF50@SN6PR1901MB2045.namprd19.prod.outlook.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
x86/Kconfig: Explicitly enumerate i686-class CPUs in Kconfig
The X86_P6_NOP config class leaves out many i686-class CPUs. Instead,
explicitly enumerate all these CPUs.
Using a configuration with M686 currently sets X86_MINIMUM_CPU_FAMILY=5
instead of the correct value of 6.
Booting on an i586 it will fail to generate the "This kernel
requires an i686 CPU, but only detected an i586 CPU" message and
intentional halt as expected. It will instead just silently hang
when it hits i686-specific instructions.
Signed-off-by: Matthew Whitehead <tedheadster@gmail.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Arjan van de Ven <arjan@linux.intel.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/1518713696-11360-3-git-send-email-tedheadster@gmail.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
x86/Kconfig: Add missing i586-class CPUs to the X86_CMPXCHG64 Kconfig group
Several i586-class CPUs supporting this instruction are missing from
the X86_CMPXCHG64 config group.
Using a configuration with either M586TSC or M586MMX currently sets
X86_MINIMUM_CPU_FAMILY=4 instead of the correct value of 5.
Booting on an i486 it will fail to generate the "This kernel
requires an i586 CPU, but only detected an i486 CPU" message and
intentional halt as expected. It will instead just silently hang
when it hits i586-specific instructions.
The M586 CPU is not in this list because at least the Cyrix 5x86
lacks this instruction, and perhaps others.
Signed-off-by: Matthew Whitehead <tedheadster@gmail.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Arjan van de Ven <arjan@linux.intel.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/1518713696-11360-1-git-send-email-tedheadster@gmail.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
Jessica Yu [Tue, 9 Jan 2018 23:51:24 +0000 (00:51 +0100)]
kprobes: Propagate error from disarm_kprobe_ftrace()
Improve error handling when disarming ftrace-based kprobes. Like with
arm_kprobe_ftrace(), propagate any errors from disarm_kprobe_ftrace() so
that we do not disable/unregister kprobes that are still armed. In other
words, unregister_kprobe() and disable_kprobe() should not report success
if the kprobe could not be disarmed.
disarm_all_kprobes() keeps its current behavior and attempts to
disarm all kprobes. It returns the last encountered error and gives a
warning if not all probes could be disarmed.
This patch is based on Petr Mladek's original patchset (patches 2 and 3)
back in 2015, which improved kprobes error handling, found here:
https://lkml.org/lkml/2015/2/26/452
However, further work on this had been paused since then and the patches
were not upstreamed.
Based-on-patches-by: Petr Mladek <pmladek@suse.com> Signed-off-by: Jessica Yu <jeyu@kernel.org> Acked-by: Masami Hiramatsu <mhiramat@kernel.org> Cc: Ananth N Mavinakayanahalli <ananth@linux.vnet.ibm.com> Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com> Cc: David S . Miller <davem@davemloft.net> Cc: Jiri Kosina <jikos@kernel.org> Cc: Joe Lawrence <joe.lawrence@redhat.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Miroslav Benes <mbenes@suse.cz> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Petr Mladek <pmladek@suse.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: live-patching@vger.kernel.org Link: http://lkml.kernel.org/r/20180109235124.30886-3-jeyu@kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
Jessica Yu [Tue, 9 Jan 2018 23:51:23 +0000 (00:51 +0100)]
kprobes: Propagate error from arm_kprobe_ftrace()
Improve error handling when arming ftrace-based kprobes. Specifically, if
we fail to arm a ftrace-based kprobe, register_kprobe()/enable_kprobe()
should report an error instead of success. Previously, this has lead to
confusing situations where register_kprobe() would return 0 indicating
success, but the kprobe would not be functional if ftrace registration
during the kprobe arming process had failed. We should therefore take any
errors returned by ftrace into account and propagate this error so that we
do not register/enable kprobes that cannot be armed. This can happen if,
for example, register_ftrace_function() finds an IPMODIFY conflict (since
kprobe_ftrace_ops has this flag set) and returns an error. Such a conflict
is possible since livepatches also set the IPMODIFY flag for their ftrace_ops.
arm_all_kprobes() keeps its current behavior and attempts to arm all
kprobes. It returns the last encountered error and gives a warning if
not all probes could be armed.
This patch is based on Petr Mladek's original patchset (patches 2 and 3)
back in 2015, which improved kprobes error handling, found here:
https://lkml.org/lkml/2015/2/26/452
However, further work on this had been paused since then and the patches
were not upstreamed.
Based-on-patches-by: Petr Mladek <pmladek@suse.com> Signed-off-by: Jessica Yu <jeyu@kernel.org> Acked-by: Masami Hiramatsu <mhiramat@kernel.org> Cc: Ananth N Mavinakayanahalli <ananth@linux.vnet.ibm.com> Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com> Cc: David S . Miller <davem@davemloft.net> Cc: Jiri Kosina <jikos@kernel.org> Cc: Joe Lawrence <joe.lawrence@redhat.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Miroslav Benes <mbenes@suse.cz> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Petr Mladek <pmladek@suse.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: live-patching@vger.kernel.org Link: http://lkml.kernel.org/r/20180109235124.30886-2-jeyu@kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
Ingo Molnar [Fri, 16 Feb 2018 08:10:09 +0000 (09:10 +0100)]
Merge tag 'perf-core-for-mingo-4.17-20180215' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/urgent
Pull perf/core fixes from Arnaldo Carvalho de Melo:
- perf_mmap overwrite mode fixes/overhaul, prep work to get 'perf top'
using it, making it bearable to use it in large core count systems
such as Knights Landing/Mill Intel systems (Kan Liang)
- s/390 now uses syscall.tbl, just like x86-64 to generate the syscall
table id -> string tables used by 'perf trace' (Hendrik Brueckner)
- Use strtoull() instead of home grown function (Andy Shevchenko)
- Synchronize kernel ABI headers, v4.16-rc1 (Ingo Molnar)
- Document missing 'perf data --force' option (Sangwon Hong)
- Add perf vendor JSON metrics for ARM Cortex-A53 Processor (William Cohen)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Ingo Molnar <mingo@kernel.org>
Thierry Reding [Wed, 7 Feb 2018 17:40:27 +0000 (18:40 +0100)]
drm/nouveau: Make clock gate support conditional
The recently introduced clock gate support breaks on Tegra chips because
no thermal support is enabled for those devices. Conditionalize the code
on the existence of thermal support to fix this.
Fixes: b138eca661cc ("drm/nouveau: Add support for basic clockgating on Kepler1") Cc: Martin Peres <martin.peres@free.fr> Cc: Lyude Paul <lyude@redhat.com> Signed-off-by: Thierry Reding <treding@nvidia.com> Reviewed-by: Lyude Paul <lyude@redhat.com> Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Dave Airlie [Fri, 16 Feb 2018 02:33:03 +0000 (12:33 +1000)]
Merge tag 'drm-intel-fixes-2018-02-14-1' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
There are important fixes for VLV with MIPI/DSI panels,
2 clean-up patches needed for this MIPI/DSI fix,
and many fixes for GEM including fixes for Perf OA and PMU,
and fixes on scheduler and preemption.
This also includes GVT fixes: "This has one to fix GTT mmio 8b
access from guest and two simple ones for mmio switch and typo fix"
* tag 'drm-intel-fixes-2018-02-14-1' of git://anongit.freedesktop.org/drm/drm-intel:
drm/i915: Fix DSI panels with v1 MIPI sequences without a DEASSERT sequence v3
drm/i915: Free memdup-ed DSI VBT data structures on driver_unload
drm/i915: Add intel_bios_cleanup() function
drm/i915/vlv: Add cdclk workaround for DSI
drm/i915/gvt: fix one typo of render_mmio trace
drm/i915/gvt: Support BAR0 8-byte reads/writes
drm/i915/gvt: add 0xe4f0 into gen9 render list
drm/i915/pmu: Fix building without CONFIG_PM
drm/i915/pmu: Fix sleep under atomic in RC6 readout
drm/i915/pmu: Fix PMU enable vs execlists tasklet race
drm/i915: Lock out execlist tasklet while peeking inside for busy-stats
drm/i915/breadcrumbs: Ignore unsubmitted signalers
drm/i915: Don't wake the device up to check if the engine is asleep
drm/i915: Avoid truncation before clamping userspace's priority value
drm/i915/perf: Fix compiler warning for string truncation
drm/i915/perf: Fix compiler warning for string truncation
Linus Torvalds [Thu, 15 Feb 2018 22:50:32 +0000 (14:50 -0800)]
Merge tag 'acpi-4.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"These fix a system resume regression from the 4.13 cycle, clean up
device table handling in the ACPI core, update sysfs ABI documentation
of a couple of drivers and add an expected switch fall-through marker
to the SPCR table parsing code.
Specifics:
- Revert a problematic EC driver change from the 4.13 cycle that
introduced a system resume regression on Thinkpad X240 (Rafael
Wysocki).
- Clean up device tables handling in the ACPI core and the related
part of the device properties framework (Andy Shevchenko).
- Update the sysfs ABI documentatio of the dock and the INT3407
special device drivers (Aishwarya Pant).
- Add an expected switch fall-through marker to the SPCR table
parsing code (Gustavo Silva)"
* tag 'acpi-4.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: dock: document sysfs interface
ACPI / DPTF: Document dptf_power sysfs atttributes
device property: Constify device_get_match_data()
ACPI / bus: Rename acpi_get_match_data() to acpi_device_get_match_data()
ACPI / bus: Remove checks in acpi_get_match_data()
ACPI / bus: Do not traverse through non-existed device table
ACPI: SPCR: Mark expected switch fall-through in acpi_parse_spcr
ACPI / EC: Restore polling during noirq suspend/resume phases
Linus Torvalds [Thu, 15 Feb 2018 22:40:01 +0000 (14:40 -0800)]
Merge tag 'pm-4.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix a recently introduced build issue related to cpuidle and two
bugs in the PM core, update cpuidle documentation and clean up memory
allocations in the operating performance points (OPP) framework.
Specifics:
- Fix a recently introduced build issue related to cpuidle by
covering all of the relevant combinations of Kconfig options
in its header (Rafael Wysocki).
- Add missing invocation of pm_runtime_drop_link() to the
!CONFIG_SRCU variant of __device_link_del() (Lukas Wunner).
- Fix unbalanced IRQ enable in the wakeup interrupts framework
(Tony Lindgren).
- Update cpuidle sysfs ABI documentation (Aishwarya Pant).
- Use GFP_KERNEL instead of GFP_ATOMIC for allocating memory
in dev_pm_opp_init_cpufreq_table() (Jia-Ju Bai)"
* tag 'pm-4.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM: cpuidle: Fix cpuidle_poll_state_init() prototype
PM / runtime: Update links_count also if !CONFIG_SRCU
PM / wakeirq: Fix unbalanced IRQ enable for wakeirq
Documentation/ABI: update cpuidle sysfs documentation
opp: cpu: Replace GFP_ATOMIC with GFP_KERNEL in dev_pm_opp_init_cpufreq_table
Linus Torvalds [Thu, 15 Feb 2018 22:31:28 +0000 (14:31 -0800)]
Merge tag 'hwmon-for-linus-v4.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fix from Guenter Roeck:
"Fix bad temperature display on Ryzen/Threadripper"
* tag 'hwmon-for-linus-v4.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (k10temp) Only apply temperature offset if result is positive
Linus Torvalds [Thu, 15 Feb 2018 22:29:27 +0000 (14:29 -0800)]
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio fixes from Michael Tsirkin:
"This includes a bugfix for virtio 9p fs. It also fixes hybernation for
s390 guests with virtio devices"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio/s390: implement PM operations for virtio_ccw
9p/trans_virtio: discard zero-length reply
Now that USB_UHCI_BIG_ENDIAN_MMIO and USB_UHCI_BIG_ENDIAN_DESC are moved
outside of the USB_SUPPORT conditional, simply select them from
SPARC_LEON rather than by the symbol's defaults in drivers/usb/Kconfig,
similar to how it is done for USB_EHCI_BIG_ENDIAN_MMIO and
USB_EHCI_BIG_ENDIAN_DESC.
Signed-off-by: James Hogan <jhogan@kernel.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Corentin Labbe <clabbe.montjoie@gmail.com> Cc: sparclinux@vger.kernel.org Cc: linux-usb@vger.kernel.org Acked-by: David S. Miller <davem@davemloft.net>
Patchwork: https://patchwork.linux-mips.org/patch/18560/
James Hogan [Wed, 31 Jan 2018 22:24:45 +0000 (22:24 +0000)]
usb: Move USB_UHCI_BIG_ENDIAN_* out of USB_SUPPORT
Move the Kconfig symbols USB_UHCI_BIG_ENDIAN_MMIO and
USB_UHCI_BIG_ENDIAN_DESC out of drivers/usb/host/Kconfig, which is
conditional upon USB && USB_SUPPORT, so that it can be freely selected
by platform Kconfig symbols in architecture code.
For example once the MIPS_GENERIC platform selects are fixed in commit 2e6522c56552 ("MIPS: Fix typo BIG_ENDIAN to CPU_BIG_ENDIAN"), the MIPS
32r6_defconfig warns like so:
warning: (MIPS_GENERIC) selects USB_UHCI_BIG_ENDIAN_MMIO which has unmet direct dependencies (USB_SUPPORT && USB)
warning: (MIPS_GENERIC) selects USB_UHCI_BIG_ENDIAN_DESC which has unmet direct dependencies (USB_SUPPORT && USB)
Linus Torvalds [Thu, 15 Feb 2018 17:28:47 +0000 (09:28 -0800)]
Merge branch 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Ingo Molnar:
"Misc fixes:
- fix rq->lock lockdep annotation bug
- fix/improve update_curr_rt() and update_curr_dl() accounting
- update documentation
- remove unused macro"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/cpufreq: Remove unused SUGOV_KTHREAD_PRIORITY macro
sched/core: Fix DEBUG_SPINLOCK annotation for rq->lock
sched/rt: Make update_curr_rt() more accurate
sched/deadline: Make update_curr_dl() more accurate
membarrier-sync-core: Document architecture support
Linus Torvalds [Thu, 15 Feb 2018 17:05:26 +0000 (09:05 -0800)]
Merge branch 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fixes from Ingo Molnar:
"This contains two qspinlock fixes and three documentation and comment
fixes"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/semaphore: Update the file path in documentation
locking/atomic/bitops: Document and clarify ordering semantics for failed test_and_{}_bit()
locking/qspinlock: Ensure node->count is updated before initialising node
locking/qspinlock: Ensure node is initialised before updating prev->next
Documentation/locking/mutex-design: Update to reflect latest changes
perf s390: Rework system call table creation by using syscall.tbl
Recently, s390 uses a syscall.tbl input file to generate its system call
table and unistd uapi header files. Hence, update mksyscalltbl to use
it as input to create the system table for perf.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Michael Petlan <mpetlan@redhat.com> Cc: Thomas Richter <tmricht@linux.vnet.ibm.com> Cc: linux-s390@vger.kernel.org
LPU-Reference: 1518090470-2899-4-git-send-email-brueckner@linux.vnet.ibm.com Link: https://lkml.kernel.org/n/tip-bdyhllhsq1zgxv2qx4m377y6@git.kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Thomas Richter [Wed, 17 Jan 2018 08:38:31 +0000 (09:38 +0100)]
perf test: Fix test trace+probe_libc_inet_pton.sh for s390x
On Intel test case trace+probe_libc_inet_pton.sh succeeds and the
output is:
[root@f27 perf]# ./perf trace --no-syscalls
-e probe_libc:inet_pton/max-stack=3/ ping -6 -c 1 ::1
PING ::1(::1) 56 data bytes
64 bytes from ::1: icmp_seq=1 ttl=64 time=0.037 ms
--- ::1 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.037/0.037/0.037/0.000 ms
0.000 probe_libc:inet_pton:(7fa40ac618a0))
__GI___inet_pton (/usr/lib64/libc-2.26.so)
getaddrinfo (/usr/lib64/libc-2.26.so)
main (/usr/bin/ping)
The kernel stack unwinder is used, it is specified implicitly
as call-graph=fp (frame pointer).
On s390x only dwarf is available for stack unwinding. It is also
done in user space. This requires different parameter setup
and result checking for s390x and Intel.
This patch adds separate perf trace setup and result checking
for Intel and s390x. On s390x specify this command line to
get a call-graph and handle the different call graph result
checking:
[root@s35lp76 perf]# ./perf trace --no-syscalls
-e probe_libc:inet_pton/call-graph=dwarf/ ping -6 -c 1 ::1
PING ::1(::1) 56 data bytes
64 bytes from ::1: icmp_seq=1 ttl=64 time=0.041 ms
Sangwon Hong [Mon, 5 Feb 2018 11:48:35 +0000 (20:48 +0900)]
perf data: Document missing --force option
Add the --force option to the man page.
Signed-off-by: Sangwon Hong <qpakzk@gmail.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Taeung Song <treeze.taeung@gmail.com> Link: http://lkml.kernel.org/r/1517831315-31490-1-git-send-email-qpakzk@gmail.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Kan Liang [Thu, 18 Jan 2018 21:26:32 +0000 (13:26 -0800)]
perf top: Check the latency of perf_top__mmap_read()
The latency of perf_top__mmap_read() should be lower than refresh time.
If not, give some hints to reduce the latency.
Signed-off-by: Kan Liang <kan.liang@intel.com> Acked-by: Jiri Olsa <jolsa@kernel.org> Cc: Andi Kleen <ak@linux.intel.com> Cc: Jin Yao <yao.jin@linux.intel.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Wang Nan <wangnan0@huawei.com> Link: http://lkml.kernel.org/r/1516310792-208685-18-git-send-email-kan.liang@intel.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Kan Liang [Thu, 18 Jan 2018 21:26:31 +0000 (13:26 -0800)]
perf top: Switch default mode to overwrite mode
perf_top__mmap_read() has a severe performance issue in the Knights
Landing/Mill platform, when monitoring heavy load systems. It costs
several minutes to finish, which is unacceptable.
Currently, 'perf top' uses the non overwrite mode. For non overwrite
mode, it tries to read everything in the ringbuffer and doesn't pause
it. Once there are lots of samples delivered persistently, the
processing time could be very long. Also, the latest samples could be
lost when the ringbuffer is full.
For overwrite mode, it takes a snapshot for the system by pausing the
ringbuffer, which could significantly reduce the processing time. Also,
the overwrite mode always keep the latest samples. Considering the real
time requirement for 'perf top', the overwrite mode is more suitable for
it.
Actually, 'perf top' was overwrite mode. It is changed to non overwrite
mode since commit 93fc64f14472 ("perf top: Switch to non overwrite
mode"). It's better to change it back to overwrite mode by default.
For the kernel which doesn't support overwrite mode, it will fall back
to non overwrite mode.
There would be some records lost in overwrite mode because of pausing
the ringbuffer. It has little impact for the accuracy of the snapshot
and can be tolerated.
For overwrite mode, unconditionally wait 100 ms before each snapshot. It
also reduces the overhead caused by pausing ringbuffer, especially on
light load system.
Signed-off-by: Kan Liang <kan.liang@intel.com> Acked-by: Jiri Olsa <jolsa@kernel.org> Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: Jin Yao <yao.jin@linux.intel.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Wang Nan <wangnan0@huawei.com> Link: http://lkml.kernel.org/r/1516310792-208685-17-git-send-email-kan.liang@intel.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Kan Liang [Thu, 18 Jan 2018 21:26:30 +0000 (13:26 -0800)]
perf top: Remove lost events checking
There would be some records lost in overwrite mode because of pausing
the ringbuffer. It has little impact for the accuracy of the snapshot
and could be tolerated by 'perf top'.
Remove the lost events checking.
Signed-off-by: Kan Liang <kan.liang@intel.com> Acked-by: Jiri Olsa <jolsa@kernel.org> Cc: Andi Kleen <ak@linux.intel.com> Cc: Jin Yao <yao.jin@linux.intel.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Wang Nan <wangnan0@huawei.com> Link: http://lkml.kernel.org/r/1516310792-208685-16-git-send-email-kan.liang@intel.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Kan Liang [Thu, 18 Jan 2018 21:26:29 +0000 (13:26 -0800)]
perf hists browser: Add parameter to disable lost event warning
For overwrite mode, the ringbuffer will be paused. The event lost is
expected. It needs a way to notify the browser not print the warning.
It will be used later for perf top to disable lost event warning in
overwrite mode. There is no behavior change for now.
Signed-off-by: Kan Liang <kan.liang@intel.com> Acked-by: Jiri Olsa <jolsa@kernel.org> Cc: Andi Kleen <ak@linux.intel.com> Cc: Jin Yao <yao.jin@linux.intel.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Wang Nan <wangnan0@huawei.com> Link: http://lkml.kernel.org/r/1516310792-208685-15-git-send-email-kan.liang@intel.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Kan Liang [Thu, 18 Jan 2018 21:26:28 +0000 (13:26 -0800)]
perf top: Add overwrite fall back
Switch to non-overwrite mode if kernel doesnot support overwrite
ringbuffer.
It's only effect when overwrite mode is supported. No change to current
behavior.
Signed-off-by: Kan Liang <kan.liang@intel.com> Acked-by: Jiri Olsa <jolsa@kernel.org> Cc: Andi Kleen <ak@linux.intel.com> Cc: Jin Yao <yao.jin@linux.intel.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Wang Nan <wangnan0@huawei.com> Link: http://lkml.kernel.org/r/1516310792-208685-14-git-send-email-kan.liang@intel.com
[ Use perf_missing_features.write_backward instead of the non merged is_write_backward_fail() ] Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
perf evsel: Expose the perf_missing_features struct
As tools may need to adjust to missing features, as 'perf top' will, in
the next csets, to cope with a missing 'write_backward' feature.
Cc: Andi Kleen <ak@linux.intel.com> Cc: Jin Yao <yao.jin@linux.intel.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Kan Liang <kan.liang@intel.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Wang Nan <wangnan0@huawei.com> Link: https://lkml.kernel.org/n/tip-jelngl9q1ooaizvkcput9tic@git.kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Kan Liang [Thu, 18 Jan 2018 21:26:26 +0000 (13:26 -0800)]
perf top: Check per-event overwrite term
Per-event overwrite term is not forbidden in 'perf top', which can bring
problems. Because 'perf top' only support non-overwrite mode now.
Add new rules and check regarding to overwrite term for 'perf top'.
- All events either have same per-event term or don't have per-event
mode setting. Otherwise, it will error out.
- Per-event overwrite term should be consistent as opts->overwrite.
If not, updating the opts->overwrite according to per-event term.
Make it possible to support either non-overwrite or overwrite mode.
The overwrite mode is forbidden now, which will be removed when the
overwrite mode is supported later.
Signed-off-by: Kan Liang <kan.liang@intel.com> Acked-by: Jiri Olsa <jolsa@kernel.org> Cc: Andi Kleen <ak@linux.intel.com> Cc: Jin Yao <yao.jin@linux.intel.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Wang Nan <wangnan0@huawei.com> Link: http://lkml.kernel.org/r/1516310792-208685-12-git-send-email-kan.liang@intel.com
[ Renamed perf_top_overwrite_check to perf_top__overwrite_check, to follow existing convention ] Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Kan Liang [Thu, 18 Jan 2018 21:26:25 +0000 (13:26 -0800)]
perf mmap: Discard legacy interface for mmap read
Discards perf_mmap__read_backward() and perf_mmap__read_catchup(). No
tools use them.
There are tools still use perf_mmap__read_forward(). Keep it, but add
comments to point to the new interface for future use.
Signed-off-by: Kan Liang <kan.liang@intel.com> Acked-by: Jiri Olsa <jolsa@kernel.org> Cc: Andi Kleen <ak@linux.intel.com> Cc: Jin Yao <yao.jin@linux.intel.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Wang Nan <wangnan0@huawei.com> Link: http://lkml.kernel.org/r/1516310792-208685-11-git-send-email-kan.liang@intel.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Kan Liang [Thu, 18 Jan 2018 21:26:24 +0000 (13:26 -0800)]
perf test: Update mmap read functions for backward-ring-buffer test
Use the new perf_mmap__read_* interfaces for overwrite ringbuffer test.
Commiter notes:
Testing:
[root@seventh ~]# perf test -v backward
48: Read backward ring buffer :
--- start ---
test child forked, pid 8309
Using CPUID GenuineIntel-6-9E
mmap size 1052672B
mmap size 8192B
Finished reading overwrite ring buffer: rewind
test child finished with 0
---- end ----
Read backward ring buffer: Ok
[root@seventh ~]#
Signed-off-by: Kan Liang <kan.liang@intel.com> Acked-by: Jiri Olsa <jolsa@kernel.org> Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: Jin Yao <yao.jin@linux.intel.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Wang Nan <wangnan0@huawei.com> Link: http://lkml.kernel.org/r/1516310792-208685-10-git-send-email-kan.liang@intel.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Kan Liang [Thu, 18 Jan 2018 21:26:23 +0000 (13:26 -0800)]
perf mmap: Introduce perf_mmap__read_event()
Except for 'perf record', the other perf tools read events one by one
from the ring buffer using perf_mmap__read_forward(). But it only
supports non-overwrite mode.
Introduce perf_mmap__read_event() to support both non-overwrite and
overwrite mode.
It cannot use perf_mmap__read_backward(). Because it always reads the
stale buffer which is already processed. Furthermore, the forward and
backward concepts have been removed. The perf_mmap__read_backward() will
be replaced and discarded later.
Signed-off-by: Kan Liang <kan.liang@intel.com> Acked-by: Jiri Olsa <jolsa@kernel.org> Cc: Andi Kleen <ak@linux.intel.com> Cc: Jin Yao <yao.jin@linux.intel.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Wang Nan <wangnan0@huawei.com> Link: http://lkml.kernel.org/r/1516310792-208685-9-git-send-email-kan.liang@intel.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Kan Liang [Thu, 18 Jan 2018 21:26:22 +0000 (13:26 -0800)]
perf mmap: Introduce perf_mmap__read_done()
The direction of overwrite mode is backward. The last perf_mmap__read()
will set tail to map->prev. Need to correct the map->prev to head which
is the end of next read.
It will be used later.
Signed-off-by: Kan Liang <kan.liang@intel.com> Acked-by: Jiri Olsa <jolsa@kernel.org> Cc: Andi Kleen <ak@linux.intel.com> Cc: Jin Yao <yao.jin@linux.intel.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Wang Nan <wangnan0@huawei.com> Link: http://lkml.kernel.org/r/1516310792-208685-8-git-send-email-kan.liang@intel.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Kan Liang [Thu, 18 Jan 2018 21:26:21 +0000 (13:26 -0800)]
perf mmap: Discard 'prev' in perf_mmap__read()
The 'start' and 'prev' variables are duplicates in perf_mmap__read().
Use 'map->prev' to replace 'start' in perf_mmap__read_*().
Suggested-by: Wang Nan <wangnan0@huawei.com> Signed-off-by: Kan Liang <kan.liang@intel.com> Acked-by: Jiri Olsa <jolsa@kernel.org> Cc: Andi Kleen <ak@linux.intel.com> Cc: Jin Yao <yao.jin@linux.intel.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Wang Nan <wangnan0@huawei.com> Link: http://lkml.kernel.org/r/1516310792-208685-7-git-send-email-kan.liang@intel.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Kan Liang [Thu, 18 Jan 2018 21:26:20 +0000 (13:26 -0800)]
perf mmap: Add new return value logic for perf_mmap__read_init()
Improve the readability by using meaningful enum (-EAGAIN, -EINVAL and
0) to replace the three returning states (0, -1 and 1).
Suggested-by: Wang Nan <wangnan0@huawei.com> Signed-off-by: Kan Liang <kan.liang@intel.com> Acked-by: Jiri Olsa <jolsa@kernel.org> Cc: Andi Kleen <ak@linux.intel.com> Cc: Jin Yao <yao.jin@linux.intel.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Wang Nan <wangnan0@huawei.com> Link: http://lkml.kernel.org/r/1516310792-208685-6-git-send-email-kan.liang@intel.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Kan Liang [Thu, 18 Jan 2018 21:26:19 +0000 (13:26 -0800)]
perf mmap: Introduce perf_mmap__read_init()
The new function perf_mmap__read_init() is factored out from
perf_mmap__push().
It is to calculate the 'start' and 'end' of the available data in
ringbuffer.
No functional change.
Signed-off-by: Kan Liang <kan.liang@intel.com> Acked-by: Jiri Olsa <jolsa@kernel.org> Cc: Andi Kleen <ak@linux.intel.com> Cc: Jin Yao <yao.jin@linux.intel.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Wang Nan <wangnan0@huawei.com> Link: http://lkml.kernel.org/r/1516310792-208685-5-git-send-email-kan.liang@intel.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Kan Liang [Thu, 18 Jan 2018 21:26:18 +0000 (13:26 -0800)]
perf mmap: Cleanup perf_mmap__push()
The first assignment for 'start' and 'end' is redundant.
Signed-off-by: Kan Liang <kan.liang@intel.com> Acked-by: Jiri Olsa <jolsa@kernel.org> Cc: Andi Kleen <ak@linux.intel.com> Cc: Jin Yao <yao.jin@linux.intel.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Wang Nan <wangnan0@huawei.com> Link: http://lkml.kernel.org/r/1516310792-208685-4-git-send-email-kan.liang@intel.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Kan Liang [Thu, 18 Jan 2018 21:26:17 +0000 (13:26 -0800)]
perf mmap: Recalculate size for overwrite mode
In perf_mmap__push(), the 'size' need to be recalculated, otherwise the
invalid data might be pushed to the record in overwrite mode.
The issue is introduced by commit 7fb4b407a124 ("perf mmap: Don't
discard prev in backward mode").
When the ring buffer is full in overwrite mode, backward_rb_find_range()
will be called to recalculate the 'start' and 'end'. The 'size' needs to
be recalculated accordingly.
Unconditionally recalculate the 'size', not just for full ring buffer in
overwrite mode. Because:
- There is no harmful to recalculate the 'size' for other cases.
- The code of calculating 'start' and 'end' will be factored out later.
The new function does not need to return 'size'.
Signed-off-by: Kan Liang <kan.liang@intel.com> Acked-by: Jiri Olsa <jolsa@kernel.org> Cc: Andi Kleen <ak@linux.intel.com> Cc: Jin Yao <yao.jin@linux.intel.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Wang Nan <wangnan0@huawei.com> Fixes: 7fb4b407a124 ("perf mmap: Don't discard prev in backward mode") Link: http://lkml.kernel.org/r/1516310792-208685-3-git-send-email-kan.liang@intel.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Kan Liang [Thu, 18 Jan 2018 21:26:16 +0000 (13:26 -0800)]
perf evlist: Remove stale mmap read for backward
perf_evlist__mmap_read_catchup() and perf_evlist__mmap_read_backward()
are only for overwrite mode.
But they read the evlist->mmap buffer which is for non-overwrite mode.
It did not bring any serious problem yet, because there is no one use
it.
Remove the unused interfaces.
Signed-off-by: Kan Liang <kan.liang@intel.com> Acked-by: Jiri Olsa <jolsa@kernel.org> Acked-by: Wang Nan <wangnan0@huawei.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: Jin Yao <yao.jin@linux.intel.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/1516310792-208685-2-git-send-email-kan.liang@intel.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
William Cohen [Wed, 31 Jan 2018 03:28:13 +0000 (22:28 -0500)]
perf vendor events aarch64: Add JSON metrics for ARM Cortex-A53 Processor
Add JSON metrics for ARM Cortex-A53 Processor.
Unlike the Intel processors there isn't a script that automatically
generated these files. The patch was manually generated from the
documentation and the previous oprofile ARM Cortex ac53 event file patch
I made.
The relevant documentation is in the "12.9 Events" section of the ARM
Cortex A53 MPCore Processor Revision: r0p4 Technical Reference Manual.
Use that to look for additional information about the events.
Signed-off-by: William Cohen <wcohen@redhat.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/20180131032813.9564-1-wcohen@redhat.com
[ Added references provided by William Cohen ] Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
platform/x86: dell-laptop: Removed duplicates in DMI whitelist
Fixed a mistake in which several entries were duplicated in the DMI list
from the below commit fe486138 platform/x86: dell-laptop: Add 2-in-1 devices to the DMI whitelist
Signed-off-by: Alexander Abrosimov <alexander.n.abrosimov@gmail.com> Reviewed-by: Pali Rohár <pali.rohar@gmail.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Laszlo Toth [Tue, 13 Feb 2018 20:43:43 +0000 (21:43 +0100)]
platform/x86: dell-laptop: fix kbd_get_state's request value
Commit 9862b43624a5 ("platform/x86: dell-laptop: Allocate buffer on heap
rather than globally")
broke one request, changed it back to the original value.
Tested on a Dell E6540, backlight came back.
Fixes: 9862b43624a5 ("platform/x86: dell-laptop: Allocate buffer on heap rather than globally") Signed-off-by: Laszlo Toth <laszlth@gmail.com> Reviewed-by: Pali Rohár <pali.rohar@gmail.com> Reviewed-by: Mario Limonciello <mario.limonciello@dell.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Aaron Ma [Sun, 11 Feb 2018 09:18:49 +0000 (17:18 +0800)]
platform/x86: ideapad-laptop: Increase timeout to wait for EC answer
Lenovo E41-20 needs more time than 100ms to read VPC,
the funtion keys always failed responding.
Increase timeout to get the value from VPC, then
the funtion keys like mic mute key work well.
Signed-off-by: Aaron Ma <aaron.ma@canonical.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Jens Axboe [Thu, 15 Feb 2018 02:01:53 +0000 (19:01 -0700)]
Merge branch 'nvme-4.16-rc' of git://git.infradead.org/nvme into for-linus
Pull NVMe fixes from Keith:
"After syncing with Christoph and Sagi, we feel this is a good time to
send our latest fixes across most of the nvme components for 4.16"
* 'nvme-4.16-rc' of git://git.infradead.org/nvme:
nvme-rdma: fix sysfs invoked reset_ctrl error flow
nvmet: Change return code of discard command if not supported
nvme-pci: Fix timeouts in connecting state
nvme-pci: Remap CMB SQ entries on every controller reset
nvme: fix the deadlock in nvme_update_formats
nvme: Don't use a stack buffer for keep-alive command
nvme_fc: cleanup io completion
nvme_fc: correct abort race condition on resets
nvme: Fix discard buffer overrun
nvme: delete NVME_CTRL_LIVE --> NVME_CTRL_CONNECTING transition
nvme-rdma: use NVME_CTRL_CONNECTING state to mark init process
nvme: rename NVME_CTRL_RECONNECTING state to NVME_CTRL_CONNECTING
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm, mm/hwpoison: Don't unconditionally unmap kernel 1:1 pages
x86/error_inject: Make just_return_func() globally visible
x86/platform/UV: Fix GAM Range Table entries less than 1GB
x86/build: Add arch/x86/tools/insn_decoder_test to .gitignore
x86/smpboot: Fix uncore_pci_remove() indexing bug when hot-removing a physical CPU
x86/mm/kcore: Add vsyscall page to /proc/kcore conditionally
vfs/proc/kcore, x86/mm/kcore: Fix SMAP fault when dumping vsyscall user page
x86/Kconfig: Further simplify the NR_CPUS config
x86/Kconfig: Simplify NR_CPUS config
x86/MCE: Fix build warning introduced by "x86: do not use print_symbol()"
x86/cpufeature: Update _static_cpu_has() to use all named variables
x86/cpufeature: Reindent _static_cpu_has()
objtool:
- Fix paranoid_entry() frame pointer warning
- Annotate WARN()-related UD2 as reachable
- Various fixes
- Add Add Peter Zijlstra as objtool co-maintainer
Misc:
- Various x86 entry code self-test fixes
- Improve/simplify entry code stack frame generation and handling
after recent heavy-handed PTI and Spectre changes. (There's two
more WIP improvements expected here.)
- Type fix for cache entries
There's also some low risk non-fix changes I've included in this
branch to reduce backporting conflicts:
- rename a confusing x86_cpu field name
- de-obfuscate the naming of single-TLB flushing primitives"
* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (41 commits)
x86/entry/64: Fix CR3 restore in paranoid_exit()
x86/cpu: Change type of x86_cache_size variable to unsigned int
x86/spectre: Fix an error message
x86/cpu: Rename cpu_data.x86_mask to cpu_data.x86_stepping
selftests/x86/mpx: Fix incorrect bounds with old _sigfault
x86/mm: Rename flush_tlb_single() and flush_tlb_one() to __flush_tlb_one_[user|kernel]()
x86/speculation: Add <asm/msr-index.h> dependency
nospec: Move array_index_nospec() parameter checking into separate macro
x86/speculation: Fix up array_index_nospec_mask() asm constraint
x86/debug: Use UD2 for WARN()
x86/debug, objtool: Annotate WARN()-related UD2 as reachable
objtool: Fix segfault in ignore_unreachable_insn()
selftests/x86: Disable tests requiring 32-bit support on pure 64-bit systems
selftests/x86: Do not rely on "int $0x80" in single_step_syscall.c
selftests/x86: Do not rely on "int $0x80" in test_mremap_vdso.c
selftests/x86: Fix build bug caused by the 5lvl test which has been moved to the VM directory
selftests/x86/pkeys: Remove unused functions
selftests/x86: Clean up and document sscanf() usage
selftests/x86: Fix vDSO selftest segfault for vsyscall=none
x86/entry/64: Remove the unused 'icebp' macro
...
Ingo Molnar [Wed, 14 Feb 2018 07:39:11 +0000 (08:39 +0100)]
x86/entry/64: Fix CR3 restore in paranoid_exit()
Josh Poimboeuf noticed the following bug:
"The paranoid exit code only restores the saved CR3 when it switches back
to the user GS. However, even in the kernel GS case, it's possible that
it needs to restore a user CR3, if for example, the paranoid exception
occurred in the syscall exit path between SWITCH_TO_USER_CR3_STACK and
SWAPGS."
Josh also confirmed via targeted testing that it's possible to hit this bug.
Fix the bug by also restoring CR3 in the paranoid_exit_no_swapgs branch.
The reason we haven't seen this bug reported by users yet is probably because
"paranoid" entry points are limited to the following cases:
Amongst those entry points only machine_check is one that will interrupt an
IRQS-off critical section asynchronously - and machine check events are rare.
The other main asynchronous entries are NMI entries, which can be very high-freq
with perf profiling, but they are special: they don't use the 'idtentry' macro but
are open coded and restore user CR3 unconditionally so don't have this bug.
Reported-and-tested-by: Josh Poimboeuf <jpoimboe@redhat.com> Reviewed-by: Andy Lutomirski <luto@kernel.org> Acked-by: Thomas Gleixner <tglx@linutronix.de> Cc: Arjan van de Ven <arjan@linux.intel.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: David Woodhouse <dwmw2@infradead.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/20180214073910.boevmg65upbk3vqb@gmail.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
x86/cpu: Change type of x86_cache_size variable to unsigned int
Currently, x86_cache_size is of type int, which makes no sense as we
will never have a valid cache size equal or less than 0. So instead of
initializing this variable to -1, it can perfectly be initialized to 0
and use it as an unsigned variable instead.
Suggested-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org>
Addresses-Coverity-ID: 1464429 Link: http://lkml.kernel.org/r/20180213192208.GA26414@embeddedor.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
Andy Lutomirski [Wed, 31 Jan 2018 16:03:10 +0000 (08:03 -0800)]
x86/mm: Rename flush_tlb_single() and flush_tlb_one() to __flush_tlb_one_[user|kernel]()
flush_tlb_single() and flush_tlb_one() sound almost identical, but
they really mean "flush one user translation" and "flush one kernel
translation". Rename them to flush_tlb_one_user() and
flush_tlb_one_kernel() to make the semantics more obvious.
[ I was looking at some PTI-related code, and the flush-one-address code
is unnecessarily hard to understand because the names of the helpers are
uninformative. This came up during PTI review, but no one got around to
doing it. ]
Signed-off-by: Andy Lutomirski <luto@kernel.org> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Dave Hansen <dave.hansen@intel.com> Cc: Eduardo Valentin <eduval@amazon.com> Cc: Hugh Dickins <hughd@google.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Juergen Gross <jgross@suse.com> Cc: Kees Cook <keescook@google.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Linux-MM <linux-mm@kvack.org> Cc: Rik van Riel <riel@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Will Deacon <will.deacon@arm.com> Link: http://lkml.kernel.org/r/3303b02e3c3d049dc5235d5651e0ae6d29a34354.1517414378.git.luto@kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
Peter Zijlstra [Tue, 13 Feb 2018 13:28:19 +0000 (14:28 +0100)]
x86/speculation: Add <asm/msr-index.h> dependency
Joe Konno reported a compile failure resulting from using an MSR
without inclusion of <asm/msr-index.h>, and while the current code builds
fine (by accident) this needs fixing for future patches.