When routes corresponding to addresses are restored by
fixup_permanent_addr(), the dst_nopolicy parameter was not set.
The typical use case is a user that configures an address on a down
interface and then put this interface up.
Let's take care of this flag in addrconf_f6i_alloc(), so that every callers
benefit ont it.
CC: stable@kernel.org CC: David Forster <dforster@brocade.com> Fixes: df789fe75206 ("ipv6: Provide ipv6 version of "disable_policy" sysctl") Reported-by: Siwar Zitouni <siwar.zitouni@6wind.com> Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Reviewed-by: David Ahern <dsahern@kernel.org> Link: https://lore.kernel.org/r/20220623120015.32640-1-nicolas.dichtel@6wind.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
By not checking whether llseek is NULL, this might jump to NULL. Also,
it doesn't check FMODE_LSEEK. Fix this by using vfs_llseek(), which
always does the right thing.
Fixes: f44158485826 ("cifsd: add file operations") Cc: stable@vger.kernel.org Cc: linux-cifs@vger.kernel.org Cc: Ronnie Sahlberg <lsahlber@redhat.com> Cc: Hyunchul Lee <hyc.lee@gmail.com> Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Reviewed-by: Namjae Jeon <linkinjeon@kernel.org> Acked-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
generic/091, 263 test failed since commit f66f8b94e7f2 ("cifs: when
extending a file with falloc we should make files not-sparse").
FSCTL_ZERO_DATA sets the range of bytes to zero without extending file
size. The VFS_FALLOCATE_FL_KEEP_SIZE flag should be used even on
non-sparse files.
Cc: stable@vger.kernel.org Reviewed-by: Hyunchul Lee <hyc.lee@gmail.com> Signed-off-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
amdgpu: [mmhub0] no-retry page fault (src_id:0 ring:40 vmid:8 pasid:32769, for process test_basic pid 3305 thread test_basic pid 3305)
amdgpu: in page starting at address 0x00007ff990003000 from IH client 0x12 (VMC)
amdgpu: VM_L2_PROTECTION_FAULT_STATUS:0x00840051
amdgpu: Faulty UTCL2 client ID: MP1 (0x0)
amdgpu: MORE_FAULTS: 0x1
amdgpu: WALKER_ERROR: 0x0
amdgpu: PERMISSION_FAULTS: 0x5
amdgpu: MAPPING_ERROR: 0x0
amdgpu: RW: 0x1
When memory is allocated by kfd, no one triggers the tlb flush for MMHUB0.
There is page fault from MMHUB0.
v2:fix indentation
v3:change subject and fix indentation
Signed-off-by: Ruili Ji <ruiliji2@amd.com> Reviewed-by: Philip Yang <philip.yang@amd.com> Reviewed-by: Aaron Liu <aaron.liu@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
We can look inside the fixed buffer table only while holding
->uring_lock, however in some cases we don't do the right async prep for
IORING_OP_{WRITE,READ}_FIXED ending up with NULL req->imu forcing making
an io-wq worker to try to resolve the fixed buffer without proper
locking.
Move req->imu setup into early req init paths, i.e. io_prep_rw(), which
is called unconditionally for rw requests and under uring_lock.
Fixes: 634d00df5e1cf ("io_uring: add full-fledged dynamic buffers support") Signed-off-by: Pavel Begunkov <asml.silence@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Vladimir Oltean [Tue, 28 Jun 2022 17:20:15 +0000 (20:20 +0300)]
net: mscc: ocelot: allow unregistered IP multicast flooding to CPU
BugLink: https://bugs.launchpad.net/bugs/1986724
Since commit 4cf35a2b627a ("net: mscc: ocelot: fix broken IP multicast
flooding") from v5.12, unregistered IP multicast flooding is
configurable in the ocelot driver for bridged ports. However, by writing
0 to the PGID_MCIPV4 and PGID_MCIPV6 port masks at initialization time,
the CPU port module, for which ocelot_port_set_mcast_flood() is not
called, will have unknown IP multicast flooding disabled.
This makes it impossible for an application such as smcroute to work
properly, since all IP multicast traffic received on a standalone port
is treated as unregistered (and dropped).
Starting with commit 7569459a52c9 ("net: dsa: manage flooding on the CPU
ports"), the limitation above has been lifted, because when standalone
ports become IFF_PROMISC or IFF_ALLMULTI, ocelot_port_set_mcast_flood()
would be called on the CPU port module, so unregistered multicast is
flooded to the CPU on an as-needed basis.
But between v5.12 and v5.18, IP multicast flooding to the CPU has
remained broken, promiscuous or not.
Delete the inexplicable premature optimization of clearing PGID_MCIPV4
and PGID_MCIPV6 as part of the init sequence, and allow unregistered IP
multicast to be flooded freely to the CPU port module.
Fixes: a556c76adc05 ("net: mscc: Add initial Ocelot switch support") Cc: stable@kernel.org Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Ping-Ke Shih answered[1] a question for a user about an rtl8821ce device that
reported RFE 6, which the driver did not support. Ping-Ke suggested a possible
fix, but the user never reported back.
A second user discovered the above thread and tested the proposed fix.
Accordingly, I am pushing this change, even though I am not the author.
When calling setattr_prepare() to determine the validity of the
attributes the ia_{g,u}id fields contain the value that will be written
to inode->i_{g,u}id. This is exactly the same for idmapped and
non-idmapped mounts and allows callers to pass in the values they want
to see written to inode->i_{g,u}id.
When group ownership is changed a caller whose fsuid owns the inode can
change the group of the inode to any group they are a member of. When
searching through the caller's groups we need to use the gid mapped
according to the idmapped mount otherwise we will fail to change
ownership for unprivileged users.
Consider a caller running with fsuid and fsgid 1000 using an idmapped
mount that maps id 65534 to 1000 and 65535 to 1001. Consequently, a file
owned by 65534:65535 in the filesystem will be owned by 1000:1001 in the
idmapped mount.
The caller now requests the gid of the file to be changed to 1000 going
through the idmapped mount. In the vfs we will immediately map the
requested gid to the value that will need to be written to inode->i_gid
and place it in attr->ia_gid. Since this idmapped mount maps 65534 to
1000 we place 65534 in attr->ia_gid.
When we check whether the caller is allowed to change group ownership we
first validate that their fsuid matches the inode's uid. The
inode->i_uid is 65534 which is mapped to uid 1000 in the idmapped mount.
Since the caller's fsuid is 1000 we pass the check.
We now check whether the caller is allowed to change inode->i_gid to the
requested gid by calling in_group_p(). This will compare the passed in
gid to the caller's fsgid and search the caller's additional groups.
Since we're dealing with an idmapped mount we need to pass in the gid
mapped according to the idmapped mount. This is akin to checking whether
a caller is privileged over the future group the inode is owned by. And
that needs to take the idmapped mount into account. Note, all helpers
are nops without idmapped mounts.
Last cycle we extended the idmapped mounts infrastructure to support
idmapped mounts of idmapped filesystems (No such filesystem yet exist.).
Since then, the meaning of an idmapped mount is a mount whose idmapping
is different from the filesystems idmapping.
While doing that work we missed to adapt the acl translation helpers.
They still assume that checking for the identity mapping is enough. But
they need to use the no_idmapping() helper instead.
Note, POSIX ACLs are always translated right at the userspace-kernel
boundary using the caller's current idmapping and the initial idmapping.
The order depends on whether we're coming from or going to userspace.
The filesystem's idmapping doesn't matter at the border.
Consequently, if a non-idmapped mount is passed we need to make sure to
always pass the initial idmapping as the mount's idmapping and not the
filesystem idmapping. Since it's irrelevant here it would yield invalid
ids and prevent setting acls for filesystems that are mountable in a
userns and support posix acls (tmpfs and fuse).
I verified the regression reported in [1] and verified that this patch
fixes it. A regression test will be added to xfstests in parallel.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215849 Fixes: bd303368b776 ("fs: support mapped mounts of mapped filesystems") Cc: Seth Forshee <sforshee@digitalocean.com> Cc: Christoph Hellwig <hch@lst.de> Cc: <stable@vger.kernel.org> # 5.15+ Cc: <regressions@lists.linux.dev> Signed-off-by: Christian Brauner (Microsoft) <brauner@kernel.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Christian Brauner (Microsoft) <brauner@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
In previous patches we added new and modified existing helpers to handle
idmapped mounts of filesystems mounted with an idmapping. In this final
patch we convert all relevant places in the vfs to actually pass the
filesystem's idmapping into these helpers.
With this the vfs is in shape to handle idmapped mounts of filesystems
mounted with an idmapping. Note that this is just the generic
infrastructure. Actually adding support for idmapped mounts to a
filesystem mountable with an idmapping is follow-up work.
In this patch we extend the definition of an idmapped mount from a mount
that that has the initial idmapping attached to it to a mount that has
an idmapping attached to it which is not the same as the idmapping the
filesystem was mounted with.
As before we do not allow the initial idmapping to be attached to a
mount. In addition this patch prevents that the idmapping the filesystem
was mounted with can be attached to a mount created based on this
filesystem.
This has multiple reasons and advantages. First, attaching the initial
idmapping or the filesystem's idmapping doesn't make much sense as in
both cases the values of the i_{g,u}id and other places where k{g,u}ids
are used do not change. Second, a user that really wants to do this for
whatever reason can just create a separate dedicated identical idmapping
to attach to the mount. Third, we can continue to use the initial
idmapping as an indicator that a mount is not idmapped allowing us to
continue to keep passing the initial idmapping into the mapping helpers
to tell them that something isn't an idmapped mount even if the
filesystem is mounted with an idmapping.
Since we'll be passing the filesystem's idmapping in even more places in
the following patches and we do already dereference struct inode to get
to the filesystem's idmapping multiple times add a tiny helper.
Enable the mapped_fs{g,u}id() helpers to support filesystems mounted
with an idmapping. Apart from core mapping helpers that use
mapped_fs{g,u}id() to initialize struct inode's i_{g,u}id fields xfs is
the only place that uses these low-level helpers directly.
The patch only extends the helpers to be able to take the filesystem
idmapping into account. Since we don't actually yet pass the
filesystem's idmapping in no functional changes happen. This will happen
in a final patch.
Now that we ported all places to use the new low-level mapping helpers
that are able to support filesystems mounted with an idmapping we can
remove the old low-level mapping helpers. With the removal of these old
helpers we also conclude the renaming of the mapping helpers we started
in commit a65e58e791a1 ("fs: document and rename fsid helpers").
In a few places the vfs needs to interact with bare k{g,u}ids directly
instead of struct inode. These are just a few. In previous patches we
introduced low-level mapping helpers that are able to support
filesystems mounted an idmapping. This patch simply converts the places
to use these new helpers.
Currently we only support idmapped mounts for filesystems mounted
without an idmapping. This was a conscious decision mentioned in
multiple places (cf. e.g. [1]).
As explained at length in [3] it is perfectly fine to extend support for
idmapped mounts to filesystem's mounted with an idmapping should the
need arise. The need has been there for some time now. Various container
projects in userspace need this to run unprivileged and nested
unprivileged containers (cf. [2]).
Before we can port any filesystem that is mountable with an idmapping to
support idmapped mounts we need to first extend the mapping helpers to
account for the filesystem's idmapping. This again, is explained at
length in our documentation at [3] but I'll give an overview here again.
Currently, the low-level mapping helpers implement the remapping
algorithms described in [3] in a simplified manner. Because we could
rely on the fact that all filesystems supporting idmapped mounts are
mounted without an idmapping the translation step from or into the
filesystem idmapping could be skipped.
In order to support idmapped mounts of filesystem's mountable with an
idmapping the translation step we were able to skip before cannot be
skipped anymore. A filesystem mounted with an idmapping is very likely
to not use an identity mapping and will instead use a non-identity
mapping. So the translation step from or into the filesystem's idmapping
in the remapping algorithm cannot be skipped for such filesystems. More
details with examples can be found in [3].
This patch adds a few new and prepares some already existing low-level
mapping helpers to perform the full translation algorithm explained in
[3]. The low-level helpers can be written in a way that they only
perform the additional translation step when the filesystem is indeed
mounted with an idmapping.
If the low-level helpers detect that they are not dealing with an
idmapped mount they can simply return the relevant k{g,u}id unchanged;
no remapping needs to be performed at all. The no_idmapping() helper
detects whether the shortcut can be used.
If the low-level helpers detected that they are dealing with an idmapped
mount but the underlying filesystem is mounted without an idmapping we
can rely on the previous shorcut and can continue to skip the
translation step from or into the filesystem's idmapping.
These checks guarantee that only the minimal amount of work is
performed. As before, if idmapped mounts aren't used the low-level
helpers are idempotent and no work is performed at all.
This patch adds the helpers mapped_k{g,u}id_fs() and
mapped_k{g,u}id_user(). Following patches will port all places to
replace the old k{g,u}id_into_mnt() and k{g,u}id_from_mnt() with these
two new helpers. After the conversion is done k{g,u}id_into_mnt() and
k{g,u}id_from_mnt() will be removed. This also concludes the renaming of
the mapping helpers we started in [4]. Now, all mapping helpers will
started with the "mapped_" prefix making everything nice and consistent.
The mapped_k{g,u}id_fs() helpers replace the k{g,u}id_into_mnt()
helpers. They are to be used when k{g,u}ids are to be mapped from the
vfs, e.g. from from struct inode's i_{g,u}id. Conversely, the
mapped_k{g,u}id_user() helpers replace the k{g,u}id_from_mnt() helpers.
They are to be used when k{g,u}ids are to be written to disk, e.g. when
entering from a system call to change ownership of a file.
This patch only introduces the helpers. It doesn't yet convert the
relevant places to account for filesystem mounted with an idmapping.
If the caller's fs{g,u}id aren't mapped in the mount's idmapping we can
return early and skip the check whether the mapped fs{g,u}id also have a
mapping in the filesystem's idmapping. If the fs{g,u}id aren't mapped in
the mount's idmapping they consequently can't be mapped in the
filesystem's idmapping. So there's no point in checking that.
The low-level mapping helpers were so far crammed into fs.h. They are
out of place there. The fs.h header should just contain the higher-level
mapping helpers that interact directly with vfs objects such as struct
super_block or struct inode and not the bare mapping helpers. Similarly,
only vfs and specific fs code shall interact with low-level mapping
helpers. And so they won't be made accessible automatically through
regular {g,u}id helpers.
Multiple places open-code the same check to determine whether a given
mount is idmapped. Introduce a simple helper function that can be used
instead. This allows us to get rid of the fragile open-coding. We will
later change the check that is used to determine whether a given mount
is idmapped. Introducing a helper allows us to do this in a single
place instead of doing it for multiple places.
In commit 02b9984d6408, we pushed a sync_filesystem() call from the VFS
into xfs_fs_remount. The only time that we ever need to push dirty file
data or metadata to disk for a remount is if we're remounting the
filesystem read only, so this really could be moved to xfs_remount_ro.
Once we've moved the call site, actually check the return value from
sync_filesystem.
Fixes: 02b9984d6408 ("fs: push sync_filesystem() down to the file system's remount_fs()") Signed-off-by: Darrick J. Wong <djwong@kernel.org> Reviewed-by: Dave Chinner <dchinner@redhat.com> Signed-off-by: Leah Rumancik <leah.rumancik@gmail.com> Acked-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
While I was running with KASAN and lockdep enabled, I stumbled upon an
KASAN report about a UAF to a freed CIL checkpoint. Looking at the
comment for xfs_log_item_in_current_chkpt, it seems pretty obvious to me
that the original patch to xfs_defer_finish_noroll should have done
something to lock the CIL to prevent it from switching the CIL contexts
while the predicate runs.
For upper level code that needs to know if a given log item is new
enough not to need relogging, add a new wrapper that takes the CIL
context lock long enough to sample the current CIL context. This is
kind of racy in that the CIL can switch the contexts immediately after
sampling, but that's ok because the consequence is that the defer ops
code is a little slow to relog items.
==================================================================
BUG: KASAN: use-after-free in xfs_log_item_in_current_chkpt+0x139/0x160 [xfs]
Read of size 8 at addr ffff88804ea5f608 by task fsstress/527999
Memory state around the buggy address: ffff88804ea5f500: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff88804ea5f580: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
>ffff88804ea5f600: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^ ffff88804ea5f680: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff88804ea5f700: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
==================================================================
Fixes: 4e919af7827a ("xfs: periodically relog deferred intent items") Signed-off-by: Darrick J. Wong <djwong@kernel.org> Reviewed-by: Dave Chinner <dchinner@redhat.com> Signed-off-by: Leah Rumancik <leah.rumancik@gmail.com> Acked-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Got a report that a repeated crash test of a container host would
eventually fail with a log recovery error preventing the system from
mounting the root filesystem. It manifested as a directory leaf node
corruption on writeback like so:
XFS (loop0): Mounting V5 Filesystem
XFS (loop0): Starting recovery (logdev: internal)
XFS (loop0): Metadata corruption detected at xfs_dir3_leaf_check_int+0x99/0xf0, xfs_dir3_leaf1 block 0x12faa158
XFS (loop0): Unmount and run xfs_repair
XFS (loop0): First 128 bytes of corrupted metadata buffer: 00000000: 00 00 00 00 00 00 00 00 3d f1 00 00 e1 9e d5 8b ........=....... 00000010: 00 00 00 00 12 fa a1 58 00 00 00 29 00 00 1b cc .......X...).... 00000020: 91 06 78 ff f7 7e 4a 7d 8d 53 86 f2 ac 47 a8 23 ..x..~J}.S...G.# 00000030: 00 00 00 00 17 e0 00 80 00 43 00 00 00 00 00 00 .........C...... 00000040: 00 00 00 2e 00 00 00 08 00 00 17 2e 00 00 00 0a ................ 00000050: 02 35 79 83 00 00 00 30 04 d3 b4 80 00 00 01 50 .5y....0.......P 00000060: 08 40 95 7f 00 00 02 98 08 41 fe b7 00 00 02 d4 .@.......A...... 00000070: 0d 62 ef a7 00 00 01 f2 14 50 21 41 00 00 00 0c .b.......P!A....
XFS (loop0): Corruption of in-memory data (0x8) detected at xfs_do_force_shutdown+0x1a/0x20 (fs/xfs/xfs_buf.c:1514). Shutting down.
XFS (loop0): Please unmount the filesystem and rectify the problem(s)
XFS (loop0): log mount/recovery failed: error -117
XFS (loop0): log mount failed
Tracing indicated that we were recovering changes from a transaction
at LSN 0x29/0x1c16 into a buffer that had an LSN of 0x29/0x1d57.
That is, log recovery was overwriting a buffer with newer changes on
disk than was in the transaction. Tracing indicated that we were
hitting the "recovery immediately" case in
xfs_buf_log_recovery_lsn(), and hence it was ignoring the LSN in the
buffer.
The code was extracting the LSN correctly, then ignoring it because
the UUID in the buffer did not match the superblock UUID. The
problem arises because the UUID check uses the wrong UUID - it
should be checking the sb_meta_uuid, not sb_uuid. This filesystem
has sb_uuid != sb_meta_uuid (which is fine), and the buffer has the
correct matching sb_meta_uuid in it, it's just the code checked it
against the wrong superblock uuid.
The is no corruption in the filesystem, and failing to recover the
buffer due to a write verifier failure means the recovery bug did
not propagate the corruption to disk. Hence there is no corruption
before or after this bug has manifested, the impact is limited
simply to an unmountable filesystem....
This was missed back in 2015 during an audit of incorrect sb_uuid
usage that resulted in commit fcfbe2c4ef42 ("xfs: log recovery needs
to validate against sb_meta_uuid") that fixed the magic32 buffers to
validate against sb_meta_uuid instead of sb_uuid. It missed the
magicda buffers....
Fixes: ce748eaa65f2 ("xfs: create new metadata UUID field and incompat flag") Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Leah Rumancik <leah.rumancik@gmail.com> Acked-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
As part of multiple customer escalations due to file data corruption
after copy on write operations, I wrote some fstests that use fsstress
to hammer on COW to shake things loose. Regrettably, I caught some
filesystem shutdowns due to incorrect rmap operations with the following
loop:
mount <filesystem> # (0)
fsstress <run only readonly ops> & # (1)
while true; do
fsstress <run all ops>
mount -o remount,ro # (2)
fsstress <run only readonly ops>
mount -o remount,rw # (3)
done
When (2) happens, notice that (1) is still running. xfs_remount_ro will
call xfs_blockgc_stop to walk the inode cache to free all the COW
extents, but the blockgc mechanism races with (1)'s reader threads to
take IOLOCKs and loses, which means that it doesn't clean them all out.
Call such a file (A).
When (3) happens, xfs_remount_rw calls xfs_reflink_recover_cow, which
walks the ondisk refcount btree and frees any COW extent that it finds.
This function does not check the inode cache, which means that incore
COW forks of inode (A) is now inconsistent with the ondisk metadata. If
one of those former COW extents are allocated and mapped into another
file (B) and someone triggers a COW to the stale reservation in (A), A's
dirty data will be written into (B) and once that's done, those blocks
will be transferred to (A)'s data fork without bumping the refcount.
The results are catastrophic -- file (B) and the refcount btree are now
corrupt. Solve this race by forcing the xfs_blockgc_free_space to run
synchronously, which causes xfs_icwalk to return to inodes that were
skipped because the blockgc code couldn't take the IOLOCK. This is safe
to do here because the VFS has already prohibited new writer threads.
Fixes: 10ddf64e420f ("xfs: remove leftover CoW reservations when remounting ro") Signed-off-by: Darrick J. Wong <djwong@kernel.org> Reviewed-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Chandan Babu R <chandan.babu@oracle.com> Signed-off-by: Leah Rumancik <leah.rumancik@gmail.com> Acked-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When testing xfstests xfs/126 on lastest upstream kernel, it will hang on some machine.
Adding a getxattr operation after xattr corrupted, I can reproduce it 100%.
When getxattr calls xfs_attr_node_get function, xfs_da3_node_lookup_int fails with EFSCORRUPTED in
xfs_attr_node_hasname because we have use blocktrash to random it in xfs/126. So it
free state in internal and xfs_attr_node_get doesn't do xfs_buf_trans release job.
Then subsequent removexattr will hang because of it.
This bug was introduced by kernel commit 07120f1abdff ("xfs: Add xfs_has_attr and subroutines").
It adds xfs_attr_node_hasname helper and said caller will be responsible for freeing the state
in this case. But xfs_attr_node_hasname will free state itself instead of caller if
xfs_da3_node_lookup_int fails.
Fix this bug by moving the step of free state into caller.
Also, use "goto error/out" instead of returning error directly in xfs_attr_node_addname_find_attr and
xfs_attr_node_removename_setup function because we should free state ourselves.
Fixes: 07120f1abdff ("xfs: Add xfs_has_attr and subroutines") Signed-off-by: Yang Xu <xuyang2018.jy@fujitsu.com> Reviewed-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Leah Rumancik <leah.rumancik@gmail.com> Acked-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
If writeback I/O to a COW extent fails, the COW fork blocks are
punched out and the data fork blocks left alone. It is possible for
COW fork blocks to overlap non-shared data fork blocks (due to
cowextsz hint prealloc), however, and writeback unconditionally maps
to the COW fork whenever blocks exist at the corresponding offset of
the page undergoing writeback. This means it's quite possible for a
COW fork extent to overlap delalloc data fork blocks, writeback to
convert and map to the COW fork blocks, writeback to fail, and
finally for ioend completion to cancel the COW fork blocks and leave
stale data fork delalloc blocks around in the inode. The blocks are
effectively stale because writeback failure also discards dirty page
state.
If this occurs, it is likely to trigger assert failures, free space
accounting corruption and failures in unrelated file operations. For
example, a subsequent reflink attempt of the affected file to a new
target file will trip over the stale delalloc in the source file and
fail. Several of these issues are occasionally reproduced by
generic/648, but are reproducible on demand with the right sequence
of operations and timely I/O error injection.
To fix this problem, update the ioend failure path to also punch out
underlying data fork delalloc blocks on I/O error. This is analogous
to the writeback submission failure path in xfs_discard_page() where
we might fail to map data fork delalloc blocks and consistent with
the successful COW writeback completion path, which is responsible
for unmapping from the data fork and remapping in COW fork blocks.
Fixes: 787eb485509f ("xfs: fix and streamline error handling in xfs_end_io") Signed-off-by: Brian Foster <bfoster@redhat.com> Reviewed-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Leah Rumancik <leah.rumancik@gmail.com> Acked-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
For kmalloc() allocations SLOB prepends the blocks with a 4-byte header,
and it puts the size of the allocated blocks in that header.
Blocks allocated with kmem_cache_alloc() allocations do not have that
header.
SLOB explodes when you allocate memory with kmem_cache_alloc() and then
try to free it with kfree() instead of kmem_cache_free().
SLOB will assume that there is a header when there is none, read some
garbage to size variable and corrupt the adjacent objects, which
eventually leads to hang or panic.
Let's make XFS work with SLOB by using proper free function.
Fixes: 9749fee83f38 ("xfs: enable the xfs_defer mechanism to process extents to free") Signed-off-by: Rustam Kovhaev <rkovhaev@gmail.com> Reviewed-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Leah Rumancik <leah.rumancik@gmail.com> Acked-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
EXPORT_SYMBOL and __init is a bad combination because the .init.text
section is freed up after the initialization. Hence, modules cannot
use symbols annotated __init. The access to a freed symbol may end up
with kernel panic.
modpost used to detect it, but it had been broken for a decade.
Commit 28438794aba4 ("modpost: fix section mismatch check for exported
init/exit sections") fixed it so modpost started to warn it again, then
this showed up:
MODPOST vmlinux.symvers
WARNING: modpost: vmlinux.o(___ksymtab_gpl+tick_nohz_full_setup+0x0): Section mismatch in reference from the variable __ksymtab_tick_nohz_full_setup to the function .init.text:tick_nohz_full_setup()
The symbol tick_nohz_full_setup is exported and annotated __init
Fix this by removing the __init annotation of tick_nohz_full_setup or drop the export.
Drop the export because tick_nohz_full_setup() is only called from the
built-in code in kernel/sched/isolation.c.
Fixes: ae9e557b5be2 ("time: Export tick start/stop functions for rcutorture") Reported-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Masahiro Yamada <masahiroy@kernel.org> Tested-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Thomas Backlund <tmb@tmb.nu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The platform's RNG must be available before random_init() in order to be
useful for initial seeding, which in turn means that it needs to be
called from setup_arch(), rather than from an init call. Fortunately,
each platform already has a setup_arch function pointer, which means
it's easy to wire this up. This commit also removes some noisy log
messages that don't add much.
Fixes: a489043f4626 ("powerpc/pseries: Implement arch_get_random_long() based on H_RANDOM") Cc: stable@vger.kernel.org # v3.13+ Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20220611151015.548325-4-Jason@zx2c4.com Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Fixes: 3fdc7d3fe4c0 ("kbuild: link vmlinux only once for CONFIG_TRIM_UNUSED_KSYMS") Signed-off-by: Masahiro Yamada <masahiroy@kernel.org> Tested-by: Sami Tolvanen <samitolvanen@google.com> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Build ID events associate a file name with a build ID. However, when
using perf inject, there is no guarantee that the file on the current
machine at the current time has that build ID. Fix by comparing the
build IDs and skip adding to the cache if they are different.
This comment wasn't updated when we moved from read() to read_iter(), so
this patch makes the trivial fix.
Fixes: 1b388e7765f2 ("random: convert to using fops->read_iter()") Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Since commit f02e8a6596b7 ("module: Sort exported symbols"),
EXPORT_SYMBOL* is placed in the individual section ___ksymtab(_gpl)+<sym>
(3 leading underscores instead of 2).
Since then, modpost cannot detect the bad combination of EXPORT_SYMBOL
and __init/__exit.
Fix the .fromsec field.
Fixes: f02e8a6596b7 ("module: Sort exported symbols") Signed-off-by: Masahiro Yamada <masahiroy@kernel.org> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
of_find_compatible_node() returns a node pointer with refcount
incremented, we should use of_node_put() on it when done.
Add missing of_node_put() to avoid refcount leak.
Fixes: 415f59142d9d ("ARM: cns3xxx: initial DT support") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Acked-by: Krzysztof Halasa <khalasa@piap.pl> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
of_parse_phandle() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
This function doesn't call of_node_put() in some error paths.
To unify the structure, Add put_node label and goto it on errors.
Fixes: 6e7674c3c6df ("memory: Add DMC driver for Exynos5422") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Reviewed-by: Lukasz Luba <lukasz.luba@arm.com> Link: https://lore.kernel.org/r/20220602041721.64348-1-linmq006@gmail.com Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
of_find_compatible_node() returns a node pointer with refcount
incremented, we should use of_node_put() on it when done.
Add missing of_node_put() to avoid refcount leak.
Fixes: 1d22924e1c4e ("ARM: Add platform support for LSI AXM55xx SoC") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Link: https://lore.kernel.org/r/20220601090548.47616-1-linmq006@gmail.com' Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
of_find_matching_node() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
In brcmstb_init_sram, it pass dn to of_address_to_resource(),
of_address_to_resource() will call of_find_device_by_node() to take
reference, so we should release the reference returned by
of_find_matching_node().
Fixes: 0b741b8234c8 ("soc: bcm: brcmstb: Add support for S2/S3/S5 suspend states (ARM)") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
of_find_matching_node() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
of_node_put() checks null pointer.
Fixes: fce9e5bb2526 ("ARM: EXYNOS: Add support for mapping PMU base address via DT") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Link: https://lore.kernel.org/r/20220523145513.12341-1-linmq006@gmail.com Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Contrary to what was believed at the time, the ramp delay of 150us is not
plenty for the PU LDO with the default step time of 512 pulses of the 24MHz
clock. Measurements have shown that after enabling the LDO the voltage on
VDDPU_CAP jumps to ~750mV in the first step and after that the regulator
executes the normal ramp up as defined by the step size control.
This means it takes the regulator between 360us and 370us to ramp up to
the nominal 1.15V voltage for this power domain. With the old setting of
the ramp delay the power up of the PU GPC domain would happen in the middle
of the regulator ramp with the voltage being at around 900mV. Apparently
this was enough for most units to properly power up the peripherals in the
domain and execute the reset. Some units however, fail to power up properly,
especially when the chip is at a low temperature. In that case any access
to the GPU registers would yield an incorrect result with no way to recover
from this situation.
Change the ramp delay to 380us to cover the measured ramp up time with a
bit of additional slack.
Fixes: 40130d327f72 ("ARM: dts: imx6qdl: Allow disabling the PU regulator, add a enable ramp delay") Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Move the power domain to its actual user. This keeps the power domain
enabled even when the USB host is runtime suspended. This is necessary
to detect any downstream events, like device attach.
Fixes: 02f8eb40ef7b ("ARM: dts: imx7s: Add power domain for imx7d HSIC") Suggested-by: Jun Li <jun.li@nxp.com> Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
dp_catalog_ctrl_reset() will software reset DP controller. But it will
not reset programmable registers to default value. DP driver still have
to clear mask bits to interrupt status registers to disable interrupts
after software reset of controller.
At current implementation, dp_ctrl_reset_irq_ctrl() will software reset dp
controller but did not call dp_catalog_ctrl_enable_irq(false) to clear hpd
related interrupt mask bits to disable hpd related interrupts due to it
mistakenly think hpd related interrupt mask bits will be cleared by software
reset of dp controller automatically. This mistake may cause system to crash
during suspending procedure due to unexpected irq fired and trigger event
thread to access dp controller registers with controller clocks are disabled.
This patch fixes system crash during suspending problem by removing "enable"
flag condition checking at dp_ctrl_reset_irq_ctrl() so that hpd related
interrupt mask bits are cleared to prevent unexpected from happening.
Changes in v2:
-- add more details commit text
Changes in v3:
-- add synchrons_irq()
-- add atomic_t suspended
Changes in v4:
-- correct Fixes's commit ID
-- remove synchrons_irq()
Changes in v5:
-- revise commit text
Changes in v6:
-- add event_lock to protect "suspended"
Changes in v7:
-- delete "suspended" flag
Fixes: 989ebe7bc446 ("drm/msm/dp: do not initialize phy until plugin interrupt received") Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/486591/ Link: https://lore.kernel.org/r/1652804494-19650-1-git-send-email-quic_khsieh@quicinc.com Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The platform's RNG must be available before random_init() in order to be
useful for initial seeding, which in turn means that it needs to be
called from setup_arch(), rather than from an init call.
Complicating things, however, is that POWER8 systems need some per-cpu
state and kmalloc, which isn't available at this stage. So we split
things up into an early phase and a later opportunistic phase. This
commit also removes some noisy log messages that don't add much.
Fixes: a4da0d50b2a0 ("powerpc: Implement arch_get_random_long/int() for powernv") Cc: stable@vger.kernel.org # v3.13+ Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
[mpe: Add of_node_put(), use pnv naming, minor change log editing] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20220621140849.127227-1-Jason@zx2c4.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Add a special case to block_rtas_call() to allow the ibm,platform-dump RTAS
call through the RTAS filter if the buffer address is 0.
According to PAPR, ibm,platform-dump is called with a null buffer address
to notify the platform firmware that processing of a particular dump is
finished.
Without this, on a pseries machine with CONFIG_PPC_RTAS_FILTER enabled, an
application such as rtas_errd that is attempting to retrieve a dump will
encounter an error at the end of the retrieval process.
Fixes: bd59380c5ba4 ("powerpc/rtas: Restrict RTAS requests from userspace") Cc: stable@vger.kernel.org Reported-by: Sathvika Vasireddy <sathvika@linux.ibm.com> Signed-off-by: Andrew Donnellan <ajd@linux.ibm.com> Reviewed-by: Tyrel Datwyler <tyreld@linux.ibm.com> Reviewed-by: Nathan Lynch <nathanl@linux.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20220614134952.156010-1-ajd@linux.ibm.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
On execve[at], we are zero'ing out most of the thread register state
including gpr[0], which contains the syscall number. Due to this, we
fail to trigger the syscall exit tracepoint properly. Fix this by
retaining gpr[0] in the thread register state.
The platform's RNG must be available before random_init() in order to be
useful for initial seeding, which in turn means that it needs to be
called from setup_arch(), rather than from an init call. Fortunately,
each platform already has a setup_arch function pointer, which means
it's easy to wire this up. This commit also removes some noisy log
messages that don't add much.
Fixes: c25769fddaec ("powerpc/microwatt: Add support for hardware random number generator") Cc: stable@vger.kernel.org # v5.14+ Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20220611151015.548325-2-Jason@zx2c4.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Fix a boot crash on a c8000 machine as reported by Dave. Basically it changes
patch_map() to return an alias mapping to the to-be-patched code in order to
prevent writing to write-protected memory.
Signed-off-by: Helge Deller <deller@gmx.de> Suggested-by: John David Anglin <dave.anglin@bell.net> Cc: stable@vger.kernel.org # v5.2+ Link: https://lore.kernel.org/all/e8ec39e8-25f8-e6b4-b7ed-4cb23efc756e@bell.net/ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
In calibrate_ccount(), of_find_compatible_node() will return a node
pointer with refcount incremented. We should use of_node_put() when
it is not used anymore.
Cc: stable@vger.kernel.org Signed-off-by: Liang He <windhl@126.com>
Message-Id: <20220617124432.4049006-1-windhl@126.com> Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
In machine_setup(), of_find_compatible_node() will return a node
pointer with refcount incremented. We should use of_node_put() when
it is not used anymore.
Cc: stable@vger.kernel.org Signed-off-by: Liang He <windhl@126.com>
Message-Id: <20220617115323.4046905-1-windhl@126.com> Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
fwnode_handle_put() should be used when terminating
device_for_each_child_node() iteration with break or return to prevent
stale device node references from being left behind.
Fixes: d935eddd2799 ("iio: adc: Add driver for Texas Instruments ADS131E0x ADC family") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Jialin Zhang <zhangjialin11@huawei.com> Link: https://lore.kernel.org/r/20220517033020.2033324-1-zhangjialin11@huawei.com Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
of_parse_phandle() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: ef04070692a2 ("iio: adc: adi-axi-adc: add support for AXI ADC IP core") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Link: https://lore.kernel.org/r/20220524074517.45268-1-linmq006@gmail.com Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
fwnode_handle_put() should be used when terminating
device_for_each_child_node() iteration with break or return to prevent
stale device node references from being left behind.
Fixes: d484c21bacfa ("iio: adc: Add driver for Renesas RZ/G2L A/D converter") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Jialin Zhang <zhangjialin11@huawei.com> Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/r/20220517033526.2035735-1-zhangjialin11@huawei.com Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Since commit 9bcf15f75cac ("iio: adc: axp288: Fix TS-pin handling") we
preserve the bias current set by the firmware at boot. This fixes issues
we were seeing on various models.
Some models like the Nuvision Solo 10 Draw tablet actually need the
old hardcoded 80ųA bias current for battery temperature monitoring
to work properly.
Add a quirk entry for the Nuvision Solo 10 Draw to the DMI quirk table
to restore setting the bias current to 80ųA on this model.
Fixes: 9bcf15f75cac ("iio: adc: axp288: Fix TS-pin handling") BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=215882 Signed-off-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20220506095040.21008-1-hdegoede@redhat.com Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The check for spurious IRQs introduced in 695e2f5c289bb assumed that the bits
in the control and status registers are aligned. This is true for the H7 and MP1
version, but not the F4. The interrupt was then never handled on the F4.
Instead of increasing the complexity of the comparison and check each bit specifically,
we remove this check completely and rely on the generic handler for spurious IRQs.
Fixes: 695e2f5c289b ("iio: adc: stm32-adc: fix a regression when using dma and irq") Signed-off-by: Yannick Brosseau <yannick.brosseau@gmail.com> Reviewed-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com> Link: https://lore.kernel.org/r/20220516203939.3498673-3-yannick.brosseau@gmail.com Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The irq handler was only checking the mask for the first ADCs in the case of the
F4 and H7 generation, since it was iterating up to the num_irq value. This patch add
the maximum number of ADC in the common register, which map to the number of entries of
eoc_msk and ovr_msk in stm32_adc_common_regs. This allow the handler to check all ADCs in
that module.
Tested on a STM32F429NIH6.
Fixes: 695e2f5c289b ("iio: adc: stm32-adc: fix a regression when using dma and irq") Signed-off-by: Yannick Brosseau <yannick.brosseau@gmail.com> Reviewed-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com> Link: https://lore.kernel.org/r/20220516203939.3498673-2-yannick.brosseau@gmail.com Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When introducing support for processed channels I needed
to invert the expression:
if (!iio_channel_has_info(schan, IIO_CHAN_INFO_RAW) ||
!iio_channel_has_info(schan, IIO_CHAN_INFO_SCALE))
dev_err(dev, "source channel does not support raw/scale\n");
To the inverse, meaning detect when we can usse raw+scale
rather than when we can not. This was the result:
Ooops. Spot the error. Yep old George Boole came up and bit me.
That should be an &&.
The current code "mostly works" because we have not run into
systems supporting only raw but not scale or only scale but not
raw, and I doubt there are few using the rescaler on anything
such, but let's fix the logic.
Cc: Liam Beguin <liambeguin@gmail.com> Cc: stable@vger.kernel.org Fixes: 53ebee949980 ("iio: afe: iio-rescale: Support processed channels") Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Liam Beguin <liambeguin@gmail.com> Acked-by: Peter Rosin <peda@axentia.se> Link: https://lore.kernel.org/r/20220524075448.140238-1-linus.walleij@linaro.org Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Ensure that the irq_work has completed before the trigger is freed.
==================================================================
BUG: KASAN: use-after-free in irq_work_run_list
Read of size 8 at addr 0000000064702248 by task python3/25
On fxls8471, after set the reset bit, the device will reset immediately,
will not give ACK. So ignore the return value of this reset operation,
let the following code logic to check whether the reset operation works.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com> Fixes: ecabae713196 ("iio: mma8452: Initialise before activating") Reviewed-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/1655292718-14287-1-git-send-email-haibo.chen@nxp.com Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
IIO trigger interface function iio_trigger_get() should be called after
iio_trigger_register() (or its devm analogue) strictly, because of
iio_trigger_get() acquires module refcnt based on the trigger->owner
pointer, which is initialized inside iio_trigger_register() to
THIS_MODULE.
If this call order is wrong, the next iio_trigger_put() (from sysfs
callback or "delete module" path) will dereference "default" module
refcnt, which is incorrect behaviour.
Fixes: 47196620c82f ("iio: mxc4005: add data ready trigger for mxc4005") Signed-off-by: Dmitry Rokosov <ddrokosov@sberdevices.ru> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Link: https://lore.kernel.org/r/20220524181150.9240-4-ddrokosov@sberdevices.ru Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
IIO trigger interface function iio_trigger_get() should be called after
iio_trigger_register() (or its devm analogue) strictly, because of
iio_trigger_get() acquires module refcnt based on the trigger->owner
pointer, which is initialized inside iio_trigger_register() to
THIS_MODULE.
If this call order is wrong, the next iio_trigger_put() (from sysfs
callback or "delete module" path) will dereference "default" module
refcnt, which is incorrect behaviour.
Fixes: 0668a4e4d297 ("iio: accel: bma180: Fix indio_dev->trig assignment") Signed-off-by: Dmitry Rokosov <ddrokosov@sberdevices.ru> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Link: https://lore.kernel.org/r/20220524181150.9240-2-ddrokosov@sberdevices.ru Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
IIO trigger interface function iio_trigger_get() should be called after
iio_trigger_register() (or its devm analogue) strictly, because of
iio_trigger_get() acquires module refcnt based on the trigger->owner
pointer, which is initialized inside iio_trigger_register() to
THIS_MODULE.
If this call order is wrong, the next iio_trigger_put() (from sysfs
callback or "delete module" path) will dereference "default" module
refcnt, which is incorrect behaviour.
Fixes: c1288b833881 ("iio: accel: kxcjk-1013: Increment ref counter for indio_dev->trig") Signed-off-by: Dmitry Rokosov <ddrokosov@sberdevices.ru> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Link: https://lore.kernel.org/r/20220524181150.9240-3-ddrokosov@sberdevices.ru Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
IIO trigger interface function iio_trigger_get() should be called after
iio_trigger_register() (or its devm analogue) strictly, because of
iio_trigger_get() acquires module refcnt based on the trigger->owner
pointer, which is initialized inside iio_trigger_register() to
THIS_MODULE.
If this call order is wrong, the next iio_trigger_put() (from sysfs
callback or "delete module" path) will dereference "default" module
refcnt, which is incorrect behaviour.
Fixes: f1f065d7ac30 ("iio: chemical: ccs811: Add support for data ready trigger") Signed-off-by: Dmitry Rokosov <ddrokosov@sberdevices.ru> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Link: https://lore.kernel.org/r/20220524181150.9240-5-ddrokosov@sberdevices.ru Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
IIO trigger interface function iio_trigger_get() should be called after
iio_trigger_register() (or its devm analogue) strictly, because of
iio_trigger_get() acquires module refcnt based on the trigger->owner
pointer, which is initialized inside iio_trigger_register() to
THIS_MODULE.
If this call order is wrong, the next iio_trigger_put() (from sysfs
callback or "delete module" path) will dereference "default" module
refcnt, which is incorrect behaviour.
Fixes: e4a70e3e7d84 ("iio: humidity: add support to hts221 rh/temp combo device") Signed-off-by: Dmitry Rokosov <ddrokosov@sberdevices.ru> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Link: https://lore.kernel.org/r/20220524181150.9240-6-ddrokosov@sberdevices.ru Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
[345393.335389] F2FS-fs (vdb): sanity_check_inode: inode (ino=6d0, mode=33206) should not have inline_data, run fsck to fix
Cc: <stable@vger.kernel.org> Fixes: 677a82b44ebf ("f2fs: fix to do sanity check for inline inode") Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
We are hitting the following deadlock in production occasionally
Task 1 Task 2 Task 3 Task 4 Task 5
fsync(A)
start trans
start commit
falloc(A)
lock 5m-10m
start trans
wait for commit
fiemap(A)
lock 0-10m
wait for 5m-10m
(have 0-5m locked)
have btrfs_need_log_full_commit
!full_sync
wait_ordered_extents
finish_ordered_io(A)
lock 0-5m
DEADLOCK
We have an existing dependency of file extent lock -> transaction.
However in fsync if we tried to do the fast logging, but then had to
fall back to committing the transaction, we will be forced to call
btrfs_wait_ordered_range() to make sure all of our extents are updated.
This creates a dependency of transaction -> file extent lock, because
btrfs_finish_ordered_io() will need to take the file extent lock in
order to run the ordered extents.
Fix this by stopping the transaction if we have to do the full commit
and we attempted to do the fast logging. Then attach to the transaction
and commit it if we need to.
CC: stable@vger.kernel.org # 5.15+ Reviewed-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
In 196d59ab9ccc "btrfs: switch extent buffer tree lock to rw_semaphore"
the functions for tree read locking were rewritten, and in the process
the read lock functions started setting eb->lock_owner = current->pid.
Previously lock_owner was only set in tree write lock functions.
Read locks are shared, so they don't have exclusive ownership of the
underlying object, so setting lock_owner to any single value for a
read lock makes no sense. It's mostly harmless because write locks
and read locks are mutually exclusive, and none of the existing code
in btrfs (btrfs_init_new_buffer and print_eb_refs_lock) cares what
nonsense is written in lock_owner when no writer is holding the lock.
KCSAN does care, and will complain about the data race incessantly.
Remove the assignments in the read lock functions because they're
useless noise.
Fixes: 196d59ab9ccc ("btrfs: switch extent buffer tree lock to rw_semaphore") CC: stable@vger.kernel.org # 5.15+ Reviewed-by: Nikolay Borisov <nborisov@suse.com> Reviewed-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Zygo Blaxell <ce3g8jdj@umail.furryterror.org> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
arch/arm/boot/dts/r8a77470-iwg23s-sbc.dtb: usb@ee080100: phys: [[17, 0], [31]] is too long
From schema: Documentation/devicetree/bindings/usb/generic-ehci.yaml
arch/arm/boot/dts/r8a77470-iwg23s-sbc.dtb: usb@ee0c0100: phys: [[17, 1], [33], [21, 0]] is too long
From schema: Documentation/devicetree/bindings/usb/generic-ehci.yaml
Some USB EHCI controllers (e.g. on the Renesas RZ/G1C SoC) have multiple
PHYs. Increase the maximum number of PHYs to 3, which is sufficient for
now.
arch/arm/boot/dts/r8a77470-iwg23s-sbc.dtb: usb@ee080000: phys: [[17, 0], [31]] is too long
From schema: Documentation/devicetree/bindings/usb/generic-ohci.yaml
arch/arm/boot/dts/r8a77470-iwg23s-sbc.dtb: usb@ee0c0000: phys: [[17, 1], [33], [21, 0]] is too long
From schema: Documentation/devicetree/bindings/usb/generic-ohci.yaml
Some USB OHCI controllers (e.g. on the Renesas RZ/G1C SoC) have multiple
PHYs. Increase the maximum number of PHYs to 3, which is sufficient for
now.
The complete() function may be called even though request is not
completed. In this case, it's necessary to check request status so
as not to set device address wrongly.
Fixes: 10775eb17bee ("usb: chipidea: udc: update gadget states according to ch9")
cc: <stable@vger.kernel.org> Signed-off-by: Xu Yang <xu.yang_2@nxp.com> Link: https://lore.kernel.org/r/20220623030242.41796-1-xu.yang_2@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Re-reading a recently merged fix to the raw_gadget driver showed that
it inadvertently introduced a double-free bug in a failure pathway.
If raw_ioctl_init() encounters an error after the driver ID number has
been allocated, it deallocates the ID number before returning. But
when dev_free() runs later on, it will then try to deallocate the ID
number a second time.
Closely related to this issue is another error in the recent fix: The
ID number is stored in the raw_dev structure before the code checks to
see whether the structure has already been initialized, in which case
the new ID number would overwrite the earlier value.
The solution to both bugs is to keep the new ID number in a local
variable, and store it in the raw_dev structure only after the check
for prior initialization. No errors can occur after that point, so
the double-free will never happen.
Fixes: f2d8c2606825 ("usb: gadget: Fix non-unique driver names in raw-gadget driver") CC: Andrey Konovalov <andreyknvl@gmail.com> CC: <stable@vger.kernel.org> Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/YrMrRw5AyIZghN0v@rowland.harvard.edu Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
In a report for a separate bug (which has already been fixed by commit 5f0b5f4d50fa "usb: gadget: fix race when gadget driver register via
ioctl") in the raw-gadget driver, the syzbot console log included
error messages caused by attempted registration of a new driver with
the same name as an existing driver:
> kobject_add_internal failed for raw-gadget with -EEXIST, don't try to register things with the same name in the same directory.
> UDC core: USB Raw Gadget: driver registration failed: -17
> misc raw-gadget: fail, usb_gadget_register_driver returned -17
These errors arise because raw_gadget.c registers a separate UDC
driver for each of the UDC instances it creates, but these drivers all
have the same name: "raw-gadget". Until recently this wasn't a
problem, but when the "gadget" bus was added and UDC drivers were
registered on this bus, it became possible for name conflicts to cause
the registrations to fail. The reason is simply that the bus code in
the driver core uses the driver name as a sysfs directory name (e.g.,
/sys/bus/gadget/drivers/raw-gadget/), and you can't create two
directories with the same pathname.
To fix this problem, the driver names used by raw-gadget are made
distinct by appending a unique ID number: "raw-gadget.N", with a
different value of N for each driver instance. And to avoid the
proliferation of error handling code in the raw_ioctl_init() routine,
the error return paths are refactored into the common pattern (goto
statements leading to cleanup code at the end of the routine).
Link: https://lore.kernel.org/all/0000000000008c664105dffae2eb@google.com/ Fixes: fc274c1e9973 "USB: gadget: Add a new bus for gadgets" CC: Andrey Konovalov <andreyknvl@gmail.com> CC: <stable@vger.kernel.org> Reported-and-tested-by: syzbot+02b16343704b3af1667e@syzkaller.appspotmail.com Reviewed-by: Andrey Konovalov <andreyknvl@gmail.com> Acked-by: Hillf Danton <hdanton@sina.com> Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/YqdG32w+3h8c1s7z@rowland.harvard.edu Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Meteor Lake TCSS(Type-C Subsystem) xHCI needs to be runtime suspended
whenever possible to allow the TCSS hardware block to enter D3cold and
thus save energy.
In the same way as Intel Alder Lake TCSS (Type-C Subsystem) the Raptor
Lake TCSS xHCI needs to be runtime suspended whenever possible to
allow the TCSS hardware block to enter D3cold and thus save energy.
Cc: stable@kernel.org Signed-off-by: Tanveer Alam <tanveer1.alam@intel.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20220623111945.1557702-4-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Intel SoC PMIC is a generic name for all PMICs that are used
on Intel platforms. In particular, INTEL_SOC_PMIC kernel configuration
option refers to Crystal Cove PMIC, which has never been a part
of any Intel Broxton hardware. Drop wrong dependency from Kconfig.
Note, the correct dependency is satisfied via ACPI PMIC OpRegion driver,
which the Type-C depends on.
Fixes: d2061f9cc32d ("usb: typec: add driver for Intel Whiskey Cove PMIC USB Type-C PHY") Reported-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20220620104316.57592-1-andriy.shevchenko@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The call to check if the calibration is all zeroes is doing
it wrong: memchr_inv() returns NULL if the the calibration
contains all zeroes, but the check is for != NULL.
Fix it up. It's probably not an urgent fix because the inner
check for BIT(7) in data[13] will save us. But fix it.
Fixes: de8860b1ed47 ("iio: magnetometer: Add driver for Yamaha YAS530") Reported-by: Jakob Hauser <jahau@rocketmail.com> Cc: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20220501195029.151852-1-linus.walleij@linaro.org Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Events CPU_CYCLES and INSTRUCTIONS can be submitted with two different
perf_event attribute::type values:
- PERF_TYPE_HARDWARE: when invoked via perf tool predefined events name
cycles or cpu-cycles or instructions.
- pmu->type: when invoked via perf tool event name cpu_cf/CPU_CYLCES/ or
cpu_cf/INSTRUCTIONS/. This invocation also selects the PMU to which
the event belongs.
Handle both type of invocations identical for events CPU_CYLCES and
INSTRUCTIONS. They address the same hardware.
The result is different when event modifier exclude_kernel is also set.
Invocation with event modifier for user space event counting fails.
This device shares the PCI ID with the Samsung 970 Evo Plus that
does not need or want the quirks. Move the the quirk entry to the
core table based on the model number instead.
Fixes: bc360b0b1611 ("nvme-pci: add quirks for Samsung X5 SSDs") Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Pankaj Raghav <p.raghav@samsung.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
This particular Kioxia device times out and aborts I/O during any load,
but it's more easily observable with discards (fstrim).
The device gets to a state that is also not possible to use
"nvme set-feature" to disable APST.
Booting with nvme_core.default_ps_max_latency=0 solves the issue.
We had a dozen or so of these devices behaving this same way in
customer environments.
Signed-off-by: Enzo Matsumiya <ematsumiya@suse.de> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Commit 8a59f9d1e3d4 ("sock: Introduce sk->sk_prot->psock_update_sk_prot()")
has moved the inet_csk_has_ulp(sk) check from sk_psock_init() to
the new tcp_bpf_update_proto() function. I'm guessing that this
was done to allow creating psocks for non-inet sockets.
Unfortunately the destruction path for psock includes the ULP
unwind, so we need to fail the sk_psock_init() itself.
Otherwise if ULP is already present we'll notice that later,
and call tcp_update_ulp() with the sk_proto of the ULP
itself, which will most likely result in the ULP looping
its callbacks.
Fixes: 8a59f9d1e3d4 ("sock: Introduce sk->sk_prot->psock_update_sk_prot()") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: John Fastabend <john.fastabend@gmail.com> Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com> Tested-by: Jakub Sitnicki <jakub@cloudflare.com> Link: https://lore.kernel.org/r/20220620191353.1184629-2-kuba@kernel.org Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
This happens because virtnet_freeze() frees the receive_queue
completely (including struct xdp_rxq_info) but does not call
xdp_rxq_info_unreg(). Similarly, virtnet_restore() sets up the
receive_queue again but does not call xdp_rxq_info_reg().
Actually, parts of virtnet_freeze_down() and virtnet_restore_up()
are almost identical to virtnet_close() and virtnet_open(): only
the calls to xdp_rxq_info_(un)reg() are missing. This means that
we can fix this easily and avoid such problems in the future by
just calling virtnet_close()/open() from the freeze/restore handlers.
Aside from adding the missing xdp_rxq_info calls the only difference
is that the refill work is only cancelled if netif_running(). However,
this should not make any functional difference since the refill work
should only be active if the network interface is actually up.
Fixes: 754b8a21a96d ("virtio_net: setup xdp_rxq_info") Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com> Acked-by: Jesper Dangaard Brouer <brouer@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com> Link: https://lore.kernel.org/r/20220621114845.3650258-1-stephan.gerhold@kernkonzept.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
We need to divide the sub-irq status register offset by register
stride to get an index for the status buffer to avoid an out of
bounds write when the register stride is greater than 1.
Fixes: a2d21848d921 ("regmap: regmap-irq: Add main status register support") Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com> Link: https://lore.kernel.org/r/20220620200644.1961936-3-aidanmacdonald.0x0@gmail.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When enabling a type_in_mask irq, the type_buf contents must be
AND'd with the mask of the IRQ we're enabling to avoid enabling
other IRQs by accident, which can happen if several type_in_mask
irqs share a mask register.
Fixes: bc998a730367 ("regmap: irq: handle HW using separate rising/falling edge interrupts") Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com> Link: https://lore.kernel.org/r/20220620200644.1961936-2-aidanmacdonald.0x0@gmail.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
In current implementation ice_update_phy_type enables all link modes
for selected speed. This approach doesn't work for 1000M speeds,
because both copper (1000baseT) and optical (1000baseX) standards
cannot be enabled at once.
Fix this, by adding the function `ice_set_phy_type_from_speed()`
for 1000M speeds.
Fixes: 48cb27f2fd18 ("ice: Implement handlers for ethtool PHY/link operations") Signed-off-by: Anatolii Gerasymenko <anatolii.gerasymenko@intel.com> Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>