Mahesh Bandewar [Mon, 27 Mar 2017 18:37:35 +0000 (11:37 -0700)]
bonding: make speed, duplex setting consistent with link state
bond_update_speed_duplex() retrieves speed and duplex settings. There
is a possibility of failure in retrieving these values but caller has
to assume it's always successful. This leads to having inconsistent
slave link settings. If these (speed, duplex) values cannot be
retrieved, then keeping the link UP causes problems.
The updated bond_update_speed_duplex() returns 0 on success if it
retrieves sane values for speed and duplex. On failure it returns 1
and marks the link down.
Signed-off-by: Mahesh Bandewar <maheshb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Mahesh Bandewar [Mon, 27 Mar 2017 18:37:33 +0000 (11:37 -0700)]
bonding: improve link-status update in mii-monitoring
The primary issue is that mii-inspect phase updates link-state and
expects changes to be committed during the mii-commit phase. After
the inspect phase if it fails to acquire rtnl-mutex, the commit
phase (bond_mii_commit) doesn't get to run. This partially updated
state stays and makes the internal-state inconsistent.
e.g. setup bond0 => slaves: eth1, eth2
eth1 goes DOWN -> UP
mii_monitor()
mii-inspect()
bond_set_slave_link_state(eth1, UP, DontNotify)
rtnl_trylock() <- fails!
Next mii-monitor round
eth1: No change
mii_monitor()
mii-inspect()
eth1->link == current-status (ethtool_ops->get_link)
no-change-detected
End result:
eth1:
Link = BOND_LINK_UP
Speed = 0xfffff [SpeedUnknown]
Duplex = 0xff [DuplexUnknown]
This doesn't always happen but for some unlucky machines in a large set
of machines it creates problems.
The fix for this is to avoid making changes during inspect phase and
postpone them until acquiring the rtnl-mutex / invoking commit phase.
Signed-off-by: Mahesh Bandewar <maheshb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 28 Mar 2017 00:06:12 +0000 (17:06 -0700)]
Merge branch '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2017-03-27
This series contains updates to i40e and i40evf only.
Alex updates the driver code so that we can do bulk updates of the page
reference count instead of just incrementing it by one reference at a
time. Fixed an issue where we were not resetting skb back to NULL when
we have freed it. Cleaned up the i40e_process_skb_fields() to align with
other Intel drivers. Removed FCoE code, since it is not supported in any
of the Fortville/Fortpark hardware, so there is not much point of carrying
the code around, especially if it is broken and untested.
Harshitha fixes a bug in the driver where the calculation of the RSS size
was not taking into account the number of traffic classes enabled.
Robert fixes a potential race condition during VF reset by eliminating
IOMMU DMAR Faults caused by VF hardware and when the OS initiates a VF
reset and before the reset is finished we modify the VF's settings.
Bimmy removes a delay that is no longer needed, since it was only needed
for preproduction hardware.
Colin King fixes null pointer dereference, where VSI was being
dereferenced before the VSI NULL check.
Jake fixes an issue with the recent addition of the "client code" to the
driver, where we attempt to use an uninitialized variable, so correctly
initialize the params variable by calling i40e_client_get_params().
v2: dropped patch 5 of the original series from Carolyn since we need
more documentation and reason why the added delay, so Carolyn is
taking the time to update the patch before we re-submit it for
kernel inclusion.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jacob Keller [Mon, 20 Mar 2017 23:45:35 +0000 (16:45 -0700)]
i40e: initialize params before notifying of l2_param_changes
Probably due to some mis-merging fix a bug associated with commits d7ce6422d6e6 ("i40e: don't check params until after checking for client
instance", 2017-02-09) and 3140aa9a78c9 ("i40e: KISS the client
interface", 2017-03-14)
The first commit tried to move the initialization of the params
structure so that we didn't bother doing this if we didn't have a client
interface. You can already see that it looks fishy because of the
indentation. The second commit refactors a bunch of the interface, and
incorrectly drops the params initialization.
I believe what occurred is that internally the two patches were
re-ordered, and the merge conflicts as a result were performed
incorrectly.
Fix the use of an uninitialized variable by correctly initializing the
params variable via i40e_client_get_params().
Reported-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Colin Ian King [Mon, 20 Mar 2017 12:03:03 +0000 (12:03 +0000)]
i40evf: dereference VSI after VSI has been null checked
VSI is being dereferenced before the VSI null check; if VSI is
null we end up with a null pointer dereference. Fix this by
performing VSI deference after the VSI null check. Also remove
the need for using adapter by using vsi->back->cinst.
Detected by CoverityScan, CID#1419696, CID#1419697
("Dereference before null check")
Fixes: ed0e894de7c133 ("i40evf: add client interface") Signed-off-by: Colin Ian King <colin.king@canonical.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Tue, 21 Feb 2017 23:55:48 +0000 (15:55 -0800)]
i40e: Drop FCoE code that always evaluates to false or 0
Since FCoE isn't supported by the i40e products there isn't much point in
carrying around code that will always evaluate to false. This patch goes
through and strips out the code in several spots so that we don't go around
carrying variables and/or code that is always going to evaluate to false or
0.
Change-ID: I39d1d779c66c638b75525839db2b6208fdc809d7 Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Tue, 21 Feb 2017 23:55:47 +0000 (15:55 -0800)]
i40e: Drop FCoE code from core driver files
Looking over the code for FCoE it looks like the Rx path has been broken at
least since the last major Rx refactor almost a year ago. It seems like
FCoE isn't supported for any of the Fortville/Fortpark hardware so there
isn't much point in carrying the code around, especially if it is broken
and untested.
Change-ID: I892de8fa551cb129ce2361e738ff82ce55fa229e Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Tue, 21 Feb 2017 23:55:46 +0000 (15:55 -0800)]
i40e/i40evf: Clean-up process_skb_fields
This is a minor clean-up to make the i40e/i40evf process_skb_fields
function look a little more like what we have in igb. The Rx checksum
function called out a need for skb->protocol but I can't see where it
actually needs it. I am assuming this is something that was likely
refactored out some time ago as the Rx checksum code has gone through a few
rewrites.
Change-ID: I0b4668a34d90b61b66ded7c7c26e19a3e2d06251 Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
First, this patch eliminates IOMMU DMAR Faults caused by VF hardware.
This is done by enabling VF hardware only after VSI resources are
freed. Otherwise, hardware could DMA into memory that is (or just has
been) being freed.
Then, the VF driver is activated only after VSI resources have been
reallocated. That's because the VF driver can request resources
immediately after it's activated. So they need to be ready at that
point.
The second race condition happens when the OS initiates a VF reset,
and then before it's finished modifies VF's settings by changing its
MAC, VLAN ID, bandwidth allocation, anti-spoof checking, etc. These
functions needed to be blocked while VF is undergoing reset. Otherwise,
they could operate on data structures that had just been freed or not
yet fully initialized.
Change-ID: I43ba5a7ae2c9a1cce3911611ffc4598ae33ae3ff Signed-off-by: Robert Konklewski <robertx.konklewski@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Tue, 21 Feb 2017 23:55:41 +0000 (15:55 -0800)]
i40e/i40evf: Fix use after free in Rx cleanup path
We need to reset skb back to NULL when we have freed it in the Rx cleanup
path. I found one spot where this wasn't occurring so this patch fixes it.
Change-ID: Iaca68934200732cd4a63eb0bd83b539c95f8c4dd Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There exists a bug in the driver where the calculation of the
RSS size was not taking into account the number of traffic classes
enabled. This patch factors in the traffic classes both in
the initial configuration of the table as well as reconfiguration.
Change-ID: I34dcd345ce52faf1d6b9614bea28d450cfd5f621 Signed-off-by: Harshitha Ramamurthy <harshitha.ramamurthy@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Tue, 21 Feb 2017 23:55:39 +0000 (15:55 -0800)]
i40e/i40evf: Update code to better handle incrementing page count
Update the driver code so that we do bulk updates of the page reference
count instead of just incrementing it by one reference at a time. The
advantage to doing this is that we cut down on atomic operations and
this in turn should give us a slight improvement in cycles per packet.
In addition if we eventually move this over to using build_skb the gains
will be more noticeable.
I also found and fixed a store forwarding stall from where we were
assigning "*new_buff = *old_buff". By breaking it up into individual
copies we can avoid this and as a result the performance is slightly
improved.
Change-ID: I1d3880dece4133eca3c32423b04a5467321ccc52 Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tobias Klauser [Mon, 27 Mar 2017 06:55:11 +0000 (08:55 +0200)]
net: bfin_mac: Remove unused stats member from struct bfin_mac_local
The bfin_mac driver keeps its statistics in net_device->stats, so the
stats member in struct bfin_mac_local is unused. Remove it, as well as
the accompanying comment.
Cc: adi-buildroot-devel@lists.sourceforge.net Signed-off-by: Tobias Klauser <tklauser@distanz.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Sat, 25 Mar 2017 14:26:39 +0000 (14:26 +0000)]
netvsc: fix dereference before null check errors
ndev is being checked to see if it is a null pointer however before
the null check ndev is being dereferenced; hence there is a potential
null pointer dereference bug that needs fixing. Fix this by only
dereferencing ndev after the null check.
Detected by CoverityScan, CID#1420760, CID#140761 ("Dereference
before null check")
Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Fri, 24 Mar 2017 22:21:57 +0000 (15:21 -0700)]
net: mpls: Delete route when all nexthops have been deleted
When all devices for all nexthops in a route have been deleted, the
route is effectively dead, so remove it.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Fri, 24 Mar 2017 22:21:56 +0000 (15:21 -0700)]
net: mpls: Don't show nexthop if device has been deleted
If the device for a nexthop in a multipath route is deleted, the nexthop
is effectively removed from the route. Currently, a route dump still
returns the nexhop though without the device set:
$ ip -f mpls ro ls
100
nexthopvia inet 10.11.1.2 dev br0
nexthopvia inet 10.100.3.1 dev eth3
$ ip li del br0
$ ip -f mpls ro ls
100
nexthopvia inet 10.11.1.2 dev * dead linkdown
nexthopvia inet 10.100.3.1 dev eth3
Since the nexthop is effectively deleted, drop the hop from the route
dump.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jonas Bonn [Fri, 24 Mar 2017 22:23:21 +0000 (23:23 +0100)]
gtp: support SGSN-side tunnels
The GTP-tunnel driver is explicitly GGSN-side as it searches for PDP
contexts based on the incoming packets _destination_ address. If we
want to place ourselves on the SGSN side of the tunnel, then we want
to be identifying PDP contexts based on _source_ address.
Let it be noted that in a "real" configuration this module would never
be used: the SGSN normally does not see IP packets as input. The
justification for this functionality is for PGW load-testing applications
where the input to the SGSN is locally generally IP traffic.
This patch adds a "role" argument at GTP-link creation time to specify
whether we are on the GGSN or SGSN side of the tunnel; this flag is then
used to determine which part of the IP packet to use in determining
the PDP context.
Signed-off-by: Jonas Bonn <jonas@southpole.se> Acked-by: Pablo Neira Ayuso <pablo@netfilter.org> Acked-by: Harald Welte <laforge@gnumonks.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Jonas Bonn [Fri, 24 Mar 2017 22:23:20 +0000 (23:23 +0100)]
gtp: rename SGSN netlink attribute
This is a mostly cosmetic rename of the SGSN netlink attribute to
the GTP link. The justification for this is that we will be making
the module support decapsulation of "downstream" SGSN packets, in
which case the netlink parameter actually refers to the upstream GGSN
peer. Renaming the parameter makes the relationship clearer.
The legacy name is maintained as a define in the header file in order
to not break existing code.
Signed-off-by: Jonas Bonn <jonas@southpole.se> Acked-by: Pablo Neira Ayuso <pablo@netfilter.org> Acked-by: Harald Welte <laforge@gnumonks.org> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 25 Mar 2017 03:49:31 +0000 (20:49 -0700)]
Merge branch 'epoll-busypoll'
Alexander Duyck says:
====================
Add busy poll support for epoll
This patch set adds support for using busy polling with epoll. The main
idea behind this is that we record the NAPI ID for the last event that is
moved onto the ready list for the epoll context and then when we no longer
have any events on the ready list we begin polling with that ID. If the
busy polling does not yield any events then we will reset the NAPI ID to 0
and wait until a new event is added to the ready list with a valid NAPI ID
before we will resume busy polling.
Most of the changes in this set authored by me are meant to be cleanup or
fixes for various things. For example, I am trying to make it so that we
don't perform hash look-ups for the NAPI instance when we are only working
with sender_cpu and the like.
At the heart of this set is the last 3 patches which enable epoll support
and add support for obtaining the NAPI ID of a given socket. With these it
becomes possible for an application to make use of epoll and get optimal
busy poll utilization by stacking multiple sockets with the same NAPI ID on
the same epoll context.
v1: The first version of this series only allowed epoll to busy poll if all
of the sockets with a NAPI ID shared the same NAPI ID. I feel we were
too strict with this requirement, so I changed the behavior for v2.
v2: The second version was pretty much a full rewrite of the first set. The
main changes consisted of pulling apart several patches to better
address the need to clean up a few items and to make the code easier to
review. In the set however I went a bit overboard and was trying to fix
an issue that would only occur with 500+ years of uptime, and in the
process limited the range for busy_poll/busy_read unnecessarily.
v3: Split off the code for limiting busy_poll and busy_read into a separate
patch for net.
Updated patch that changed busy loop time tracking so that it uses
"local_clock() >> 10" as we originally did.
Tweaked "Change return type.." patch by moving declaration of "work"
inside the loop where is was accessed and always reset to 0.
Added "Acked-by" for patches that received acks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This socket option returns the NAPI ID associated with the queue on which
the last frame is received. This information can be used by the apps to
split the incoming flows among the threads based on the Rx queue on which
they are received.
If the NAPI ID actually represents a sender_cpu then the value is ignored
and 0 is returned.
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com> Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
epoll: Add busy poll support to epoll with socket fds.
This patch adds busy poll support to epoll. The implementation is meant to
be opportunistic in that it will take the NAPI ID from the last socket
that is added to the ready list that contains a valid NAPI ID and it will
use that for busy polling until the ready list goes empty. Once the ready
list goes empty the NAPI ID is reset and busy polling is disabled until a
new socket is added to the ready list.
In addition when we insert a new socket into the epoll we record the NAPI
ID and assume we are going to receive events on it. If that doesn't occur
it will be evicted as the active NAPI ID and we will resume normal
behavior.
An application can use SO_INCOMING_CPU or SO_REUSEPORT_ATTACH_C/EBPF socket
options to spread the incoming connections to specific worker threads
based on the incoming queue. This enables epoll for each worker thread
to have only sockets that receive packets from a single queue. So when an
application calls epoll_wait() and there are no events available to report,
busy polling is done on the associated queue to pull the packets.
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com> Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: Commonize busy polling code to focus on napi_id instead of socket
Move the core functionality in sk_busy_loop() to napi_busy_loop() and
make it independent of sk.
This enables re-using this function in epoll busy loop implementation.
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com> Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Fri, 24 Mar 2017 17:08:18 +0000 (10:08 -0700)]
net: Track start of busy loop instead of when it should end
This patch flips the logic we were using to determine if the busy polling
has timed out. The main motivation for this is that we will need to
support two different possible timeout values in the future and by
recording the start time rather than when we would want to end we can focus
on making the end_time specific to the task be it epoll or socket based
polling.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Fri, 24 Mar 2017 17:08:12 +0000 (10:08 -0700)]
net: Change return type of sk_busy_loop from bool to void
checking the return value of sk_busy_loop. As there are only a few
consumers of that data, and the data being checked for can be replaced
with a check for !skb_queue_empty() we might as well just pull the code
out of sk_busy_loop and place it in the spots that actually need it.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Fri, 24 Mar 2017 17:08:06 +0000 (10:08 -0700)]
net: Only define skb_mark_napi_id in one spot instead of two
Instead of defining two versions of skb_mark_napi_id I think it is more
readable to just match the format of the sk_mark_napi_id functions and just
wrap the contents of the function instead of defining two versions of the
function. This way we can save a few lines of code since we only need 2 of
the ifdef/endif but needed 5 for the extra function declaration.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Fri, 24 Mar 2017 17:08:00 +0000 (10:08 -0700)]
tcp: Record Rx hash and NAPI ID in tcp_child_process
While working on some recent busy poll changes we found that child sockets
were being instantiated without NAPI ID being set. In our first attempt to
fix it, it was suggested that we should just pull programming the NAPI ID
into the function itself since all callers will need to have it set.
In addition to the NAPI ID change I have dropped the code that was
populating the Rx hash since it was actually being populated in
tcp_get_cookie_sock.
Reported-by: Sridhar Samudrala <sridhar.samudrala@intel.com> Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Fri, 24 Mar 2017 17:07:53 +0000 (10:07 -0700)]
net: Busy polling should ignore sender CPUs
This patch is a cleanup/fix for NAPI IDs following the changes that made it
so that sender_cpu and napi_id were doing a better job of sharing the same
location in the sk_buff.
One issue I found is that we weren't validating the napi_id as being valid
before we started trying to setup the busy polling. This change corrects
that by using the MIN_NAPI_ID value that is now used in both allocating the
NAPI IDs, as well as validating them.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed [Fri, 24 Mar 2017 21:52:14 +0000 (00:52 +0300)]
net/mlx5e: Different SQ types
Different SQ types (tx, xdp, ico) are growing apart, we separate them
and remove unwanted parts in each one of them, to simplify data path and
utilize data cache.
Remove DB union from SQ structures since it is not needed anymore as we
now have different SQ data type for each SQ.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Reviewed-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
In the next patches we will introduce different SQ types,
and we would want to reuse those functions, in this patch we make them
agnostic to SQ type (txq, xdp, ico).
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Reviewed-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed [Fri, 24 Mar 2017 21:52:12 +0000 (00:52 +0300)]
net/mlx5e: Proper names for SQ/RQ/CQ functions
Rename mlx5e_{create,destroy}_{sq,rq,cq} to
mlx5e_{alloc,free}_{sq,rq,cq}.
Rename mlx5e_{enable,disable}_{sq,rq,cq} to
mlx5e_{create,destroy}_{sq,rq,cq}.
mlx5e_{enable,disable}_{sq,rq,cq} used to actually create/destroy the SQ
in FW, so we rename them to align the functions names with FW semantics.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Reviewed-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed [Fri, 24 Mar 2017 21:52:11 +0000 (00:52 +0300)]
net/mlx5e: Generalize tx helper functions for different SQ types
In the next patches we will introduce different SQ types, for that we here
generalize some TX helper functions to work with more basic SQ parameters,
in order to re-use them for the different SQ types.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Reviewed-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed [Fri, 24 Mar 2017 21:52:10 +0000 (00:52 +0300)]
net/mlx5e: Optimize XDP frame xmit
XDP SQ has a fixed size WQE (MLX5E_XDP_TX_WQEBBS = 1) and only posts
one kind of WQE (MLX5_OPCODE_SEND),
Also we initialize SQ descriptors static fields once on open_xdpsq,
rather than every time on critical path.
Optimize the code in light of those facts and add a prefetch of the TX
descriptor first thing in the xdp xmit function.
Performance improvement:
System: Intel(R) Xeon(R) CPU E5-2620 v3 @ 2.40GHz
Test case Before Now improvement
---------------------------------------------------------------
XDP TX (1 core) 13Mpps 13.7Mpps 5%
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Reviewed-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed [Fri, 24 Mar 2017 21:52:09 +0000 (00:52 +0300)]
net/mlx5e: Poll XDP TX CQ before RX CQ
Handle XDP TX completions before handling RX packets, to make sure more
free space is available for XDP TX packets a moment before handling
RX packets.
Performance improvement:
System: Intel(R) Xeon(R) CPU E5-2620 v3 @ 2.40GHz
Test case Before Now improvement
---------------------------------------------------------------
XDP Drop (1 core) 16.9Mpps 16.9Mpps No change
XDP TX (1 core) 12Mpps 13Mpps 8%
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Reviewed-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed [Fri, 24 Mar 2017 21:52:08 +0000 (00:52 +0300)]
net/mlx5e: Move XDP SQ instance into RQ
To save many rq->channel->sq dereferences in fast-path.
And rename it to xdpsq.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Reviewed-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed [Fri, 24 Mar 2017 21:52:07 +0000 (00:52 +0300)]
net/mlx5e: Move mlx5e_rq struct declaration
Move struct mlx5e_rq and friends to appear after mlx5e_sq declaration in
en.h.
We will need this for next patch to move the mlx5e_sq instance into
mlx5e_rq struct for XDP SQs.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Reviewed-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed [Fri, 24 Mar 2017 21:52:06 +0000 (00:52 +0300)]
net/mlx5e: Move XDP completion functions to rx file
XDP code belongs to RX path, move mlx5e_poll_xdp_tx_cq and
mlx5e_free_xdp_tx_descs to en_rx.c.
Rename them to mlx5e_poll_xdpsq_cq and mlx5e_free_xdpsq_descs.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Reviewed-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed [Fri, 24 Mar 2017 21:52:05 +0000 (00:52 +0300)]
net/mlx5e: Single bfreg (UAR) for all mlx5e SQs and netdevs
One is sufficient since Blue Flame is not supported anymore.
This will also come in handy for switchdev mode to save resources, since
VF representors will use same single UAR as well for their own SQs.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Reviewed-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed [Fri, 24 Mar 2017 21:52:04 +0000 (00:52 +0300)]
net/mlx5e: Xmit, no write combining
mlx5e netdev Blue Flame (write combining) support demands a lot of
overhead for a little latency gain for some special cases, this overhead
is hurting the common case.
Here we remove xmit Blue Flame support by creating all bfregs with no
write combining for all SQs, and we remove a lot of BF logic and
conditions from xmit data path.
Simplify mlx5e_tx_notify_hw (doorbell function) by removing BF related
code and by removing one memory barrier needed for WC mapped SQ doorbell
buffers, which no longer exist.
Performance improvement:
System: Intel(R) Xeon(R) CPU E5-2620 v3 @ 2.40GHz
Test case Before Now improvement
---------------------------------------------------------------
TX packets (24 threads) 50Mpps 54Mpps 8%
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Reviewed-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed [Fri, 24 Mar 2017 21:52:03 +0000 (00:52 +0300)]
net/mlx5e: Use dma_rmb rather than rmb in CQE fetch routine
Use dma_rmb in mlx5e_get_cqe rather than aggressive rmb (at least on
some architectures), this should help improve the performance on such
CPU archs where dma_rmb is optimized.
Performance improvement:
System: Intel(R) Xeon(R) CPU E5-2620 v3 @ 2.40GHz
Test case Baseline Now improvement
---------------------------------------------------------------
TX packets (24 threads) 45Mpps 50Mpps 11%
TC stack Drop (1 core) 3.45Mpps 3.6Mpps 5%
XDP Drop (1 core) 14Mpps 16.9Mpps 20%
XDP TX (1 core) 10.4Mpps 12Mpps 15%
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Reviewed-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Fri, 24 Mar 2017 21:57:22 +0000 (14:57 -0700)]
net: dsa: bcm_sf2: Add missing OF_MDIO dependency
bcm_sf2 does require the MDIO_BCM_UNIMAC driver which is now dependent
on OF_MDIO but also internally uses of_mdio.c provided routines which
are guarted with OF_MDIO.
Reported-by: kbuild test robot <fengguang.wu@intel.com> Fixes: 90eff9096c01 ("net: phy: Allow splitting MDIO bus/device support from PHYs") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 24 Mar 2017 21:47:32 +0000 (14:47 -0700)]
Merge branch 'ipv6-sr-perf-improvements'
David Lebrun says:
====================
Performances improvement for IPv6 Segment Routing
This patch series improves the performances of IPv6 SR by optimizing skb head
reallocation and extending the use of dst_cache. The overall performances improve
by 35%.
Before patch series (SRH encap):
Result: OK: 7348320(c7347271+d1048) usec, 5000000 (1000byte,0frags)
680427pps 5443Mb/sec (5443416000bps) errors: 0
After patch series (SRH encap):
Result: OK: 4774543(c4774084+d459) usec, 5000000 (1000byte,0frags)
1047220pps 8377Mb/sec (8377760000bps) errors: 0
David Lebrun [Fri, 24 Mar 2017 09:46:27 +0000 (10:46 +0100)]
ipv6: sr: use dst_cache in seg6_input
We already use dst_cache in seg6_output, when handling locally generated
packets. We extend it in seg6_input, to also handle forwarded packets, and avoid
unnecessary fib lookups.
Performances for SRH encapsulation before the patch:
Result: OK: 5656067(c5655678+d388) usec, 5000000 (1000byte,0frags)
884006pps 7072Mb/sec (7072048000bps) errors: 0
Performances after the patch:
Result: OK: 4774543(c4774084+d459) usec, 5000000 (1000byte,0frags)
1047220pps 8377Mb/sec (8377760000bps) errors: 0
Signed-off-by: David Lebrun <david.lebrun@uclouvain.be> Signed-off-by: David S. Miller <davem@davemloft.net>
David Lebrun [Fri, 24 Mar 2017 09:46:26 +0000 (10:46 +0100)]
ipv6: sr: expand skb head only if necessary
To insert or encapsulate a packet with an SRH, we need a large enough skb
headroom. Currently, we are using pskb_expand_head to inconditionally increase
the size of the headroom by the amount needed by the SRH (and IPv6 header).
If this reallocation is performed by another CPU than the one that initially
allocated the skb, then when the initial CPU kfree the skb, it will enter the
__slab_free slowpath, impacting performances.
This patch replaces pskb_expand_head with skb_cow_head, that will reallocate the
skb head only if the headroom is not large enough.
Performances for SRH encapsulation before the patch:
Result: OK: 7348320(c7347271+d1048) usec, 5000000 (1000byte,0frags)
680427pps 5443Mb/sec (5443416000bps) errors: 0
Performances after the patch:
Result: OK: 5656067(c5655678+d388) usec, 5000000 (1000byte,0frags)
884006pps 7072Mb/sec (7072048000bps) errors: 0
Signed-off-by: David Lebrun <david.lebrun@uclouvain.be> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 24 Mar 2017 20:45:07 +0000 (13:45 -0700)]
Merge branch '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2017-03-23
This series contains updates to i40e and i40e.txt documentation.
Jake provides all the changes in the series which are centered around
ntuple filter fixes and additional support. Fixed the current
implementation of .set_rxnfc, where we were not reading the mask field
for filter entries which was resulting in filters not behaving as
expected and not working correctly. When cleaning up after disabling
flow director support, ensure that the default input set is correctly
reprogrammed. Since the hardware only supports a single input set for
all flows of that type, the driver shall only allow the input set to
change if there are no other configured filters for that flow type, so
add support to detect when we can update the input set for each flow
type. Align the driver to other drivers to partition the ring_cookie
value into 8bits of VF index, along with 32bits of queue number instead
of using the user-def field. Added support to parse the user-def field
into a data structure format to allow future extensions of the user-def
filed by keeping all the code that read/writes the field into a single
location. Added support for flexible payloads passed via ethtool
user-def field. We support a single flexible word (2byte) value per
protocol type, and we handle the FLX_PIT register using a list of
flexible entries so that each flow type may be configured separately.
Enabled flow director filters for SCTPv4 packets using the ethtool
ntuple interface to enable filters. Updated the documentation on the
i40e driver to include the newly added support to ntuple filters.
Reduced complexity of a if-continue-else-break section of code by
taking advantage of using hlist_for_each_entry_continue() instead.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Fri, 24 Mar 2017 01:02:27 +0000 (19:02 -0600)]
net: mpls: Fix setting ttl_propagate for rt2
Fix copy and paste error setting rt_ttl_propagate.
Fixes: 5b441ac8784c1 ("mpls: allow TTL propagation to IP packets to be configured") Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Acked-by: Robert Shearman <rshearma@brocade.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Gao Feng [Thu, 23 Mar 2017 23:05:12 +0000 (07:05 +0800)]
tcp: sysctl: Fix a race to avoid unexpected 0 window from space
Because sysctl_tcp_adv_win_scale could be changed any time, so there
is one race in tcp_win_from_space.
For example,
1.sysctl_tcp_adv_win_scale<=0 (sysctl_tcp_adv_win_scale is negative now)
2.space>>(-sysctl_tcp_adv_win_scale) (sysctl_tcp_adv_win_scale is postive now)
As a result, tcp_win_from_space returns 0. It is unexpected.
Certainly if the compiler put the sysctl_tcp_adv_win_scale into one
register firstly, then use the register directly, it would be ok.
But we could not depend on the compiler behavior.
Signed-off-by: Gao Feng <fgao@ikuai8.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Felix Manlunas [Thu, 23 Mar 2017 20:26:28 +0000 (13:26 -0700)]
liquidio: do not reset Octeon if NIC firmware was preloaded
The PF driver is incorrectly resetting Octeon when the module parameter
"fw_type=none" is there. "fw_type=none" means the PF should not load any
firmware to the NIC because Octeon is already running preloaded firmware.
Fix it by putting an if (fw_type != none) around the reset code.
Because the Octeon reset is now conditionally gone, when unloading the
driver, conditionally send the RESET_PF command to the firmware who will
then free up PF-related data structures.
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com> Signed-off-by: Satanand Burla <satananda.burla@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: Add sysctl to toggle early demux for tcp and udp
Certain system process significant unconnected UDP workload.
It would be preferrable to disable UDP early demux for those systems
and enable it for TCP only.
By disabling UDP demux, we see these slight gains on an ARM64 system-
782 -> 788Mbps unconnected single stream UDPv4
633 -> 654Mbps unconnected UDPv4 different sources
The performance impact can change based on CPU architecure and cache
sizes. There will not much difference seen if entire UDP hash table
is in cache.
Both sysctls are enabled by default to preserve existing behavior.
v1->v2: Change function pointer instead of adding conditional as
suggested by Stephen.
v2->v3: Read once in callers to avoid issues due to compiler
optimizations. Also update commit message with the tests.
v3->v4: Store and use read once result instead of querying pointer
again incorrectly.
v4->v5: Refactor to avoid errors due to compilation with IPV6={m,n}
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org> Suggested-by: Eric Dumazet <edumazet@google.com> Cc: Stephen Hemminger <stephen@networkplumber.org> Cc: Tom Herbert <tom@herbertland.com> Cc: David Miller <davem@davemloft.net> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch series builds up on Doug's latest changes done in BCMGENET to reduce
the number of spurious interrupts in NAPI, simplify pointer arithmetic and
finally tracking of per TX ring statistics to be SMP friendly.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to c298ede2fe21 ("net: bcmgenet: simplify circular pointer
arithmetic") we don't need to complex arthimetic since we always have a
ring size that is a power of 2.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Thu, 23 Mar 2017 17:36:47 +0000 (10:36 -0700)]
net: systemport: Clear status to reduce spurious interrupts
Do something similar to commit d5810ca3252a ("net: bcmgenet: clear
status to reduce spurious interrupts") and clear interrupts right before
servicing them. This reduces the number of interrupts by 10K
interrupts/sec for a TX TCP session 1Gbits/sec.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Thu, 23 Mar 2017 17:36:46 +0000 (10:36 -0700)]
net: systemport: Track per TX ring statistics
bcm_sysport_tx_reclaim_one() is currently summing TX bytes/packets in a
way that is not SMP friendly, mutliples CPUs could run
bcm_sysport_tx_reclaim_one() independently and still update
stats->tx_bytes and stats->tx_packets, cloberring the other CPUs
statistics.
Fix this by tracking per TX rings the number of bytes, packets,
dropped and errors statistics, and provide a bcm_sysport_get_nstats()
function which aggregates everything and returns a consistent output.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 24 Mar 2017 19:51:05 +0000 (12:51 -0700)]
Merge branch 'phy-mdio-split'
Florian Fainelli says:
====================
net: phy: Allow splitting MDIO bus/device support
This patch series allows building support for MDIO bus controllers which
are sometimes usable and necessary in cases where there are no Ethernet PHYs.
Changes in v3:
- corrected of_mdio compile guards for prototypes vs. stubs
- added a missing OF_MDIO dependency for MDIO_BCM_UNIMAC
- fixed Kbuild bot reported errors against mdio-bitbang
Changes in v2:
- implement Russell's feedback
- solve the circular dependency in the CONFIG_MDIO_DEVICE + CONFIG_PHYLIB case
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Thu, 23 Mar 2017 17:01:19 +0000 (10:01 -0700)]
net: phy: Allow splitting MDIO bus/device support from PHYs
Introduce a new configuration symbol: MDIO_DEVICE which allows building
the MDIO devices and bus code, without pulling in the entire Ethernet
PHY library and devices code.
PHYLIB nows select MDIO_DEVICE and the relevant Makefile files are
updated to reflect that.
When MDIO_DEVICE (MDIO bus/device only) is selected, but not PHYLIB, we
have mdio-bus.ko as a loadable module, and it does not have a
module_exit() function because the safety of removing a bus class is
unclear.
When both MDIO_DEVICE and PHYLIB are enabled, we need to assemble
everything into a common loadable module: libphy.ko because of nasty
circular dependencies between phy.c, phy_device.c and mdio_bus.c which
are really tough to untangle.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Thu, 23 Mar 2017 17:01:17 +0000 (10:01 -0700)]
of_mdio: Correct check against CONFIG_OF
CONFIG_OF_MDIO is actually what triggers the build of drivers/of/of_mdio.c, so
providing inline stubs when CONFIG_OF_MDIO=y should be based on that symbol as
well.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Thu, 23 Mar 2017 16:02:16 +0000 (17:02 +0100)]
net: sched: choke: remove dead filter classify code
sch_choke is classless qdisc so it does not define cl_ops. Therefore
filter_list cannot be ever changed, being NULL all the time.
Reason is this check in tc_ctl_tfilter:
/* Is it classful? */
cops = q->ops->cl_ops;
if (!cops)
return -EINVAL;
So remove this dead code.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
LABBE Corentin [Thu, 23 Mar 2017 13:40:22 +0000 (14:40 +0100)]
net: stmmac: add set_mac to the stmmac_ops
Two different set_mac functions exists but stmmac_dwmac4_set_mac() is
only used for enabling and never for disabling.
So on dwmac4, the MAC RX/TX is never disabled.
This patch add a generic function pointer set_mac() to stmmac_ops and
replace all call to stmmac_set_mac/stmmac_dwmac4_set_mac by a call to
this pointer.
Since dwmac4_ops is const, set_mac cannot be modified after, and so dwmac4_ops
is duplioacted like dwmac4_dma_ops.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 24 Mar 2017 19:30:22 +0000 (12:30 -0700)]
Merge branch 'bridge-ext-learned-entries'
Nikolay Aleksandrov says
====================
net: bridge: allow user-space to add ext learned entries
This set adds the ability to add externally learned entries from
user-space. For symmetry and proper function we need to allow SW entries
to take over HW learned ones (similar to how HW can take over SW entries
currently) which is needed for our use case (evpn) where we have pure SW
ports and HW ports mixed in a single bridge. This does not play well with
switchdev devices currently because there's no feedback when the entry is
taken over, but this case has never worked anyway and feedback can be
easily added when needed.
Patch 02 simply allows to use NTF_EXT_LEARNED from user-space, we already
have Quagga patches that make use of this functionality.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
net: bridge: allow to add externally learned entries from user-space
The NTF_EXT_LEARNED flag was added for switchdev and externally learned
entries, but it can also be used for entries learned via a software
in user-space which requires dynamic entries that do not expire.
One such case that we have is with quagga and evpn which need dynamic
entries but also require to age them themselves.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: bridge: allow SW learn to take over HW fdb entries
Allow to take over an entry which was previously learned via HW when it
shows up from a SW port. This is analogous to how HW takes over SW learned
entries already.
Suggested-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jacob Keller [Tue, 7 Mar 2017 23:17:52 +0000 (15:17 -0800)]
i40e: make use of hlist_for_each_entry_continue
Replace a complex if->continue->else->break construction in
i40e_next_filter. We can simply use hlist_for_each_entry_continue
instead. This drops a lot of confusing code. The resulting code is much
easier to understand the intention, and follows the more normal pattern
for using hlist loops. We could have also used a break with a "return
next" at the end of the function, instead of return NULL, but the
current implementation is explicitly clear that when you reach the end
of the loop you get a NULL value. The alternative construction is less
clear since the reader would have to know that next is NULL at the end
of the loop.
Change-Id: Ife74ca451dd79d7f0d93c672bd42092d324d4a03 Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Mon, 6 Feb 2017 22:38:52 +0000 (14:38 -0800)]
i40e: document drivers use of ntuple filters
Add documentation describing the drivers use of ethtool ntuple filters,
including the limitations that it has due to hardware, as well as how it
reads and parses the user-def data block.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Mon, 6 Feb 2017 22:38:51 +0000 (14:38 -0800)]
i40e: add support for SCTPv4 FDir filters
Enable FDir filters for SCTPv4 packets using the ethtool ntuple
interface to enable filters. The ethtool API does not allow masking on
the verification tag.
Change-Id: I093e88a8143994c7e6f4b7b17a0bd5cf861d18e4 Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Mon, 6 Feb 2017 22:38:50 +0000 (14:38 -0800)]
i40e: implement support for flexible word payload
Add support for flexible payloads passed via ethtool user-def field.
This support is somewhat limited due to hardware design. The input set
can only be programmed once per filter type, and the flexible offset is
part of this filter input set. This means that the user cannot program
both a regular and a flexible filter at the same time for a given flow
type. Additionally, the user may not program two flexible filters of the
same flow type with different offsets, although they are allowed to
configure different values at that offset location.
We support a single flexible word (2byte) value per protocol type, and
we handle the FLX_PIT register using a list of flexible entries so that
each flow type may be configured separately.
Due to hardware implementation, the flexible data is offset from the
start of the packet payload, and thus may not be in part of the header
data. For this reason, the offset provided by the user defined data is
interpreted as a byte offset from the start of the matching payload.
Previous implementations have tried to represent the offset as from the
start of the frame, but this is not feasible because header sizes may
change due to options.
Change-Id: 36ed27995e97de63f9aea5ade5778ff038d6f811 Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Mon, 6 Feb 2017 22:38:49 +0000 (14:38 -0800)]
i40e: add parsing of flexible filter fields from userdef
Add code to parse the user-def field into a data structure format. This
code is intended to allow future extensions of the user-def field by
keeping all code that actually reads and writes the field into a single
location. This ensures that we do not litter the driver with references
to the user-def field and minimizes the amount of bitwise operations we
need to do on the data.
Add code which parses the lower 32bits into a flexible word and its
offset. This will be used in a future patch to enable flexible filters
which can match on some arbitrary data in the packet payload. For now,
we just return -EOPNOTSUPP when this is used.
Add code to fill in the user-def field when reporting the filter back,
even though we don't actually implement any user-def fields yet.
Additionally, ensure that we mask the extended FLOW_EXT bit from the
flow_type now that we will be accepting filters which have the FLOW_EXT
bit set (and thus make use of the user-def field).
Change-Id: I238845035c179380a347baa8db8223304f5f6dd7 Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Mon, 6 Feb 2017 22:38:48 +0000 (14:38 -0800)]
i40e: partition the ring_cookie to get VF index
Do not use the user-def field for determining the VF target. Instead,
similar to ixgbe, partition the ring_cookie value into 8bits of VF
index, along with 32bits of queue number. This is better than using the
user-def field, because it leaves the field open for extension in
a future patch which will enable flexible data. Also, this matches with
convention used by ixgbe and other drivers.
Change-Id: Ie36745186d817216b12f0313b99ec95cb8a9130c Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Mon, 6 Feb 2017 22:38:47 +0000 (14:38 -0800)]
i40e: allow changing input set for ntuple filters
Add support to detect when we can update the input set for each flow
type.
Because the hardware only supports a single input set for all flows of
that matching type, the driver shall only allow the input set to change
if there are no other configured filters for that flow type.
Thus, the first filter added for each flow type is allowed to change the
input set, and all future filters must match the same input set. Display
a diagnostic message whenever the filter input set changes, and
a warning whenever a filter cannot be accepted because it does not match
the configured input set.
Change-Id: Ic22e1c267ae37518bb036aca4a5694681449f283 Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Mon, 6 Feb 2017 22:38:46 +0000 (14:38 -0800)]
i40e: restore default input set for each flow type
Ensure that the default input set is correctly reprogrammed when
cleaning up after disabling flow director support. This ensures that the
programmed value will be in a clean state.
Although we do not yet have support for SCTPv4 filters, a future patch
will add support for this protocol, so we will correctly restore the
SCTPv4 input set here as well. Note that strictly speaking the default
hardware value for SCTP includes matching the verification tag. However,
the ethtool API does not have support for specifying this value, so
there is no reason to keep the verification field enabled.
This patch is the next step on the way to enabling partial tuple filters
which will be implemented in a following patch.
Change-Id: Ic22e1c267ae37518bb036aca4a5694681449f283 Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Tue, 7 Mar 2017 23:05:23 +0000 (15:05 -0800)]
i40e: check current configured input set when adding ntuple filters
Do not assume that hardware has been programmed with the default mask,
but instead read the input set registers to determine what is currently
programmed. This ensures that all programmed filters match exactly how
the hardware will interpret them, avoiding confusion regarding filter
behavior.
This sets the initial ground-work for allowing custom input sets where
some fields are disabled. A future patch will fully implement this
feature.
Instead of using bitwise negation, we'll just explicitly check for the
correct value. The use of htonl and htons are used to silence sparse
warnings. The compiler should be able to handle the constant value and
avoid actually performing a byteswap.
Change-Id: I3d8db46cb28ea0afdaac8c5b31a2bfb90e3a4102 Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Tue, 7 Mar 2017 23:05:22 +0000 (15:05 -0800)]
i40e: correctly honor the mask fields for ETHTOOL_SRXCLSRLINS
The current implementation of .set_rxnfc does not properly read the mask
field for filter entries. This results in incorrect driver behavior, as
we do not reject filters which have masks set to ignore some fields. The
current implementation simply assumes that every part of the tuple or
"input set" is specified. This results in filters not behaving as
expected, and not working correctly.
As a first step in supporting some partial filters, add code which
checks the mask fields and rejects any filters which do not have an
acceptable mask. For now, we just assume that all fields must be set.
This will get the driver one step towards allowing some partial filters.
At a minimum, the ethtool commands which previously installed filters
that would not function will now return a non-zero exit code indicating
failure instead.
We should now be meeting the minimum requirements of the .set_rxnfc API,
by ensuring that all filters we program have a valid mask value for each
field.
Finally, add code to report the mask correctly so that the ethtool
command properly reports the mask to the user.
Note that the typecast to (__be16) when checking source and destination
port masks is required because the ~ bitwise negation operator does not
correctly handle variables other than integer size.
Change-Id: Ia020149e07c87aa3fcec7b2283621b887ef0546f Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Davide Caratti [Thu, 23 Mar 2017 09:39:40 +0000 (10:39 +0100)]
sched: act_csum: don't mangle TCP and UDP GSO packets
after act_csum computes the checksum on skbs carrying GSO TCP/UDP packets,
subsequent segmentation fails because skb_needs_check(skb, true) returns
true. Because of that, skb_warn_bad_offload() is invoked and the following
message is displayed:
WARNING: CPU: 3 PID: 28 at net/core/dev.c:2553 skb_warn_bad_offload+0xf0/0xfd
<...>
projects / mirror_ubuntu-bionic-kernel.git / log