- Split DT bindings for PCIe controllers with independent MSI domains into
separate nodes for MT2712/MT7622 (Chuanjia Liu)
- Locate shared registers from "mediatek,generic-pciecfg" property
(Chuanjia Liu)
- Get IRQ from "pcie_irq" if "interrupt-names" property is present to fix
an MSI issue (Chuanjia Liu)
- Get PCI domain from "linux,pci-domain" property if present (Chuanjia Liu)
* remotes/lorenzo/pci/mediatek:
PCI: mediatek: Use PCI domain to handle ports detection
PCI: mediatek: Add new method to get irq number
PCI: mediatek: Add new method to get shared pcie-cfg base address
dt-bindings: PCI: mediatek: Update the Device tree bindings
- Add domain_nr in struct pci_host_bridge (Boqun Feng)
- Use host bridge MSI domain for root buses if present (Boqun Feng)
- Allow ARM64 virtual host bridge with no ACPI companion (e.g., Hyper-V)
(Boqun Feng)
- Make Hyper-V enumeration more generic (Arnd Bergmann)
- Set Hyper-V domain_nr at probe-time (Boqun Feng)
- Set up Hyper-V MSI domain at bridge probe-time (Boqun Feng)
- Enable Hyper-V bridge probing on ARM64 (Boqun Feng)
* remotes/lorenzo/pci/hyper-v:
PCI: hv: Turn on the host bridge probing on ARM64
PCI: hv: Set up MSI domain at bridge probing time
PCI: hv: Set ->domain_nr of pci_host_bridge at probing time
PCI: hv: Generify PCI probing
arm64: PCI: Support root bridge preparation for Hyper-V
arm64: PCI: Restructure pcibios_root_bridge_prepare()
PCI: Support populating MSI domains of root buses via bridges
PCI: Introduce domain_nr in pci_host_bridge
- Convert bool in structs to bitfield (Kishon Vijay Abraham I)
- Work around J7200 non-PCIe SERDES lane electrical issue that prevents
PCIe link training (Nadeem Athani)
- Add J7200 PCIe support to j721e (Kishon Vijay Abraham I)
- Add AM64 PCIe support to j721e (Kishon Vijay Abraham I)
- Add J7200 and AM64 device IDs to endpoint test (Kishon Vijay Abraham I)
* remotes/lorenzo/pci/cadence:
misc: pci_endpoint_test: Add deviceID for AM64 and J7200
PCI: j721e: Add PCIe support for AM64
PCI: j721e: Add PCIe support for J7200
PCI: cadence: Add quirk flag to set minimum delay in LTSSM Detect.Quiet state
PCI: cadence: Use bitfield for *quirk_retrain_flag* instead of bool
- Fix PIO config access status checking (Evan Wang)
- Increase config access polling delay to 1.5s (Pali Rohár)
- Add PCIe Root Capabilities to bridge emulation (Pali Rohár)
- Report Config Request Retry Status when Software Visibility enabled (Pali
Rohár)
- Add back configuration of PCIe resources from 'ranges' DT property and
pay attention to DT size and CPU/PCI offset to fix issues with I/O port
space (Pali Rohár)
- Serialize masking and unmasking legacy INTx interrupts (Pali Rohár)
* remotes/lorenzo/pci/aardvark:
PCI: aardvark: Fix masking and unmasking legacy INTx interrupts
PCI: aardvark: Configure PCIe resources from 'ranges' DT property
PCI: aardvark: Fix reporting CRS value
PCI: pci-bridge-emul: Add PCIe Root Capabilities Register
PCI: aardvark: Increase polling delay to 1.5s while waiting for PIO response
PCI: aardvark: Fix checking for PIO status
- Drop error message when Precision Time Measurement supported but not
enabled (Jakub Kicinski)
- Correct the pci_iomap.h header guard #endif comment (Jonathan Cameron)
- Add schedule point in proc_bus_pci_read() (Krzysztof Wilczyński)
- Make saved capability state private to core (Bjorn Helgaas)
- Sync __pci_register_driver() stub for CONFIG_PCI=n (Andy Shevchenko)
- Convert sta2x11 from PCI-DMA-API to generic DMA-API (Christophe JAILLET)
* pci/misc:
x86/PCI: sta2x11: switch from 'pci_' to 'dma_' API
PCI: Sync __pci_register_driver() stub for CONFIG_PCI=n
PCI: Make saved capability state private to core
PCI: Add schedule point in proc_bus_pci_read()
PCI: Correct the pci_iomap.h header guard #endif comment
PCI/PTM: Remove error message at boot
PCI: Fix pci_dev_str_match_path() alloc while atomic bug
x86/PCI: Add pci_numachip_init() declaration
- Remove reset_fn field from pci_dev (Amey Narkhede)
- Add sysfs interface to query and set device reset mechanism (Amey
Narkhede)
- Add pci_set_acpi_fwnode() to set ACPI_COMPANION (Shanker Donthineni)
- Use acpi_pci_power_manageable() instead of duplicating logic (Shanker
Donthineni)
- Set ACPI fwnode early and at the same time with OF (Shanker Donthineni)
- Add support for ACPI _RST reset method (Shanker Donthineni)
- Change reset function 'probe' argument to bool (Amey Narkhede)
* pci/reset:
PCI: Change the type of probe argument in reset functions
PCI: Add support for ACPI _RST reset method
PCI: Setup ACPI fwnode early and at the same time with OF
PCI: Use acpi_pci_power_manageable()
PCI: Add pci_set_acpi_fwnode() to set ACPI_COMPANION
PCI: Allow userspace to query and set device reset mechanism
PCI: Remove reset_fn field from pci_dev
PCI: Add array to track reset method ordering
PCI: Add pcie_reset_flr() with 'probe' argument
PCI: Cache PCIe Device Capabilities register
- Call Max Payload Size-related fixup quirks early, so they're considered
by pci_configure_mps() (Marek Behún)
- Restrict Max Payload Size Supported to work around ASMedia ASM1062 SATA
erratum (Marek Behún)
- Return ~0 data on pciconfig_read() CAP_SYS_ADMIN failure (Krzysztof
Wilczyński)
* pci/enumeration:
PCI: Return int from pciconfig_read() syscall
PCI: Return ~0 data on pciconfig_read() CAP_SYS_ADMIN failure
PCI: Restrict ASMedia ASM1062 SATA Max Payload Size Supported
PCI: Call Max Payload Size-related fixup quirks early
x86/PCI: sta2x11: switch from 'pci_' to 'dma_' API
The wrappers in include/linux/pci-dma-compat.h should go away.
The patch has been generated with the coccinelle script below.
It has been hand modified to use 'dma_set_mask_and_coherent()' instead of
'pci_set_dma_mask()/pci_set_consistent_dma_mask()' when applicable.
This is less verbose.
Heiner Kallweit [Thu, 26 Aug 2021 18:55:07 +0000 (20:55 +0200)]
PCI/VPD: Include post-processing in pci_vpd_find_tag()
Move pci_vpd_find_tag() post-processing from pci_vpd_find_ro_info_keyword()
to pci_vpd_find_tag(). This simplifies function pci_vpd_find_id_string()
that will be added in a subsequent patch.
HiSilicon KunPeng920 and KunPeng930 have devices that appear as PCI but are
actually on the AMBA bus. These fake PCI devices can support SVA via the
SMMU stall feature.
DT systems can indicate this in the device tree, but ACPI systems don't
have that mechanism, so add a "dma-can-stall" property manually for them.
[bhelgaas: add text from Robin as comment near quirk] Link: https://lore.kernel.org/r/1626144876-11352-4-git-send-email-zhangfei.gao@linaro.org Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org> Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org> Signed-off-by: Zhou Wang <wangzhou1@hisilicon.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Robin Murphy <robin.murphy@arm.com>
Add a driver for the DesignWare-based PCIe controller found on
RK356X. The existing pcie-rockchip-host driver is only used for
the Rockchip-designed IP found on RK3399.
Link: https://lore.kernel.org/r/20210625065511.1096935-1-xxm@rock-chips.com Tested-by: Peter Geis <pgwipeout@gmail.com> Signed-off-by: Simon Xue <xxm@rock-chips.com> Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Rob Herring <robh@kernel.org>
PCI: dwc: Remove surplus break statement after return
As part of code refactoring completed in a0fd361db8e5 ("PCI: dwc: Move
"dbi", "dbi2", and "addr_space" resource setup into common code"),
dw_plat_add_pcie_ep() was removed and the call to the dw_pcie_ep_init() was
moved into dw_plat_pcie_probe().
This left a break statement behind that is not needed any more as as
dw_plat_pcie_probe() returns immediately after calling dw_pcie_ep_init().
Remove this surplus break statement that became dead code.
Suggested-by: Bjorn Helgaas <bhelgaas@google.com> Link: https://lore.kernel.org/r/20210701210252.1638709-1-kw@linux.com Signed-off-by: Krzysztof Wilczyński <kw@linux.com> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
PCI: artpec6: Remove surplus break statement after return
As part of code refactoring completed in a0fd361db8e5 ("PCI: dwc: Move
"dbi", "dbi2", and "addr_space" resource setup into common code"),
artpec6_add_pcie_ep() was removed and the call to the dw_pcie_ep_init()
was moved into artpec6_pcie_probe().
This left a break statement behind that is not needed any more as
artpec6_pcie_probe() returns immediately after calling dw_pcie_ep_init().
Remove this surplus break statement that became dead code.
Link: https://lore.kernel.org/r/20210701204401.1636562-1-kw@linux.com Signed-off-by: Krzysztof Wilczyński <kw@linux.com> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Stuart Hayes [Wed, 12 May 2021 21:33:14 +0000 (03:03 +0530)]
PCI/portdrv: Enable Bandwidth Notification only if port supports it
Previously we assumed that all Root Ports and Switch Downstream Ports
supported Link Bandwidth Notification. Per spec, this is only required
for Ports supporting Links wider than x1 and/or multiple Link speeds
(PCIe r5.0, sec 7.5.3.6).
Because we assumed all Ports supported it, we tried to set up a Bandwidth
Notification IRQ, which failed for devices that don't support IRQs at all,
which meant pcieport didn't attach to the Port at all.
Check the Link Bandwidth Notification Capability bit and enable the service
only when the Port supports it.
[bhelgaas: commit log] Fixes: e8303bb7a75c ("PCI/LINK: Report degraded links via link bandwidth notification") Link: https://lore.kernel.org/r/20210512213314.7778-1-stuart.w.hayes@gmail.com Signed-off-by: Stuart Hayes <stuart.w.hayes@gmail.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Lukas Wunner <lukas@wunner.de> Cc: stable@vger.kernel.org
PCI: Allow PASID on fake PCIe devices without TLP prefixes
Some systems, e.g., HiSilicon KunPeng920 and KunPeng930, have devices that
appear as PCI but are actually on the AMBA bus. Some of these fake PCI
devices support a PASID-like feature and they do have a working PASID
capability even though they do not use the PCIe Transport Layer Protocol
and do not support TLP prefixes.
Add a pasid_no_tlp bit for this "PASID works without TLP prefixes" case and
update pci_enable_pasid() so it can enable PASID on these devices.
Set this bit for HiSilicon KunPeng920 and KunPeng930.
Chuanjia Liu [Mon, 23 Aug 2021 03:27:55 +0000 (11:27 +0800)]
dt-bindings: PCI: mediatek: Update the Device tree bindings
There are two independent PCIe controllers in MT2712 and MT7622
platform. Each of them should contain an independent MSI domain.
In old dts architecture, MSI domain will be inherited from the root
bridge, and all of the devices will share the same MSI domain.
Hence that, the PCIe devices will not work properly if the irq number
which required is more than 32.
Split the PCIe node for MT2712 and MT7622 platform to comply with
the hardware design and fix MSI issue.
Pali Rohár [Fri, 20 Aug 2021 15:50:20 +0000 (17:50 +0200)]
PCI: aardvark: Fix masking and unmasking legacy INTx interrupts
irq_mask and irq_unmask callbacks need to be properly guarded by raw spin
locks as masking/unmasking procedure needs atomic read-modify-write
operation on hardware register.
Link: https://lore.kernel.org/r/20210820155020.3000-1-pali@kernel.org Reported-by: Marc Zyngier <maz@kernel.org> Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Acked-by: Marc Zyngier <maz@kernel.org> Cc: stable@vger.kernel.org
Heiner Kallweit [Sun, 22 Aug 2021 13:52:01 +0000 (15:52 +0200)]
bnx2: Replace open-coded byte swapping with swab32s()
Read NVRAM directly into buffer and use swab32s() to byte swap it in-place
instead of reading it into the end of the buffer and swapping it manually
while copying it.
Since PCI_HYPERV depends on PCI_MSI_IRQ_DOMAIN which selects
GENERIC_MSI_IRQ_DOMAIN, we can use dev_set_msi_domain() to set up the
MSI domain at probing time, and this works for both x86 and ARM64.
Therefore use it as the preparation for ARM64 Hyper-V PCI support.
As a result, no longer need to maintain ->fwnode in x86 specific
pci_sysdata, and make hv_pcibus_device own it instead.
PCI: hv: Set ->domain_nr of pci_host_bridge at probing time
No functional change, just store and maintain the PCI domain number in
the ->domain_nr of pci_host_bridge. Note that we still need to keep
the copy of domain number in x86-specific pci_sysdata, because x86 is
not a PCI_DOMAINS_GENERIC=y architecture, so the ->domain_nr of
pci_host_bridge doesn't work for it yet.
In order to support ARM64 Hyper-V PCI, we need to set up the bridge at
probing time because ARM64 is a PCI_DOMAIN_GENERIC=y arch and we don't
have pci_config_window (ARM64 sysdata) for a PCI root bus on Hyper-V, so
it's impossible to retrieve the information (e.g. PCI domains, MSI
domains) from bus sysdata on ARM64 after creation.
Originally in create_root_hv_pci_bus(), pci_create_root_bus() is used to
create the root bus and the corresponding bridge based on x86 sysdata.
Now we create a bridge first and then call pci_scan_root_bus_bridge(),
which allows us to do the necessary set-ups for the bridge.
arm64: PCI: Support root bridge preparation for Hyper-V
Currently at root bridge preparation, the corresponding ACPI device will
be set as the companion, however for a Hyper-V virtual PCI root bridge,
there is no corresponding ACPI device, because a Hyper-V virtual PCI
root bridge is discovered via VMBus rather than ACPI table. In order to
support this, we need to make pcibios_root_bridge_prepare() work with
cfg->parent being NULL.
Use a NULL pointer as the ACPI device if there is no corresponding ACPI
device, and this is fine because: 1) ACPI_COMPANION_SET() can work with
the second parameter being NULL, 2) semantically, if a NULL pointer is
set via ACPI_COMPANION_SET(), ACPI_COMPANION() (the read API for this
field) will return NULL, and since ACPI_COMPANION() may return NULL, so
users must have handled the cases where it returns NULL, and 3) since
there is no corresponding ACPI device, it would be wrong to use any
other value here.
PCI: Support populating MSI domains of root buses via bridges
Currently, at probing time, the MSI domains of root buses are populated
if either the information of MSI domain is available from firmware (DT
or ACPI), or arch-specific sysdata is used to pass the fwnode of the MSI
domain. These two conditions don't cover all, e.g. Hyper-V virtual PCI
on ARM64, which doesn't have the MSI information in the firmware and
couldn't use arch-specific sysdata because running on an architecture
with PCI_DOMAINS_GENERIC=y.
To support populating MSI domains of the root buses at the probing when
neither of the above condition is true, the ->msi_domain of the
corresponding bridge device is used: in pci_host_bridge_msi_domain(),
which should return the MSI domain of the root bus, the ->msi_domain of
the corresponding bridge is fetched first as a potential value of the
MSI domain of the root bus.
In order to use the approach to populate MSI domains, the driver needs
to dev_set_msi_domain() on the bridge before calling
pci_register_host_bridge(), and makes sure GENERIC_MSI_IRQ_DOMAIN=y.
Another advantage of this new approach is providing an arch-independent
way to populate MSI domains, which allows sharing the driver code as
much as possible between architectures.
Currently we retrieve the PCI domain number of the host bridge from the
bus sysdata (or pci_config_window if PCI_DOMAINS_GENERIC=y). Actually
we have the information at PCI host bridge probing time, and it makes
sense that we store it into pci_host_bridge. One benefit of doing so is
the requirement for supporting PCI on Hyper-V for ARM64, because the
host bridge of Hyper-V doesn't have pci_config_window, whereas ARM64 is
a PCI_DOMAINS_GENERIC=y arch, so we cannot retrieve the PCI domain
number from pci_config_window on ARM64 Hyper-V guest.
As the preparation for ARM64 Hyper-V PCI support, we introduce the
domain_nr in pci_host_bridge and a sentinel value to allow drivers to
set domain numbers properly at probing time. Currently
CONFIG_PCI_DOMAINS_GENERIC=y archs are only users of this
newly-introduced field.
Andy Shevchenko [Fri, 13 Aug 2021 15:36:19 +0000 (18:36 +0300)]
PCI: Sync __pci_register_driver() stub for CONFIG_PCI=n
The CONFIG_PCI=y case got a new parameter long time ago. Sync the stub as
well.
[bhelgaas: add parameter names] Fixes: 725522b5453d ("PCI: add the sysfs driver name to all modules") Link: https://lore.kernel.org/r/20210813153619.89574-1-andriy.shevchenko@linux.intel.com Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Zhen Lei [Tue, 13 Jul 2021 07:22:36 +0000 (15:22 +0800)]
PCI: Optimize pci_resource_len() to reduce kernel size
pci_resource_end() can be 0 only when pci_resource_start() is 0.
Otherwise, it is definitely an error. In this case, pci_resource_len()
should be regarded as 0. Therefore, determining whether
pci_resource_start() and pci_resource_end() are both 0 can be reduced to
determining only whether pci_resource_end() is 0.
Although only one condition judgment is reduced, the macro function
pci_resource_len() is widely referenced in the kernel. I used defconfig to
compile the latest kernel on X86, and its binary code size was reduced by
about 3KB.
Alex Williamson [Fri, 18 Jun 2021 20:55:14 +0000 (14:55 -0600)]
PCI/ACS: Enforce pci=noats with Transaction Blocking
PCIe Address Translation Services (ATS) provides a mechanism for a device
to provide an on-device caching translation agent (device IOTLB). We
already have a means to disable support for this feature via the pci=noats
option. For untrusted and externally facing devices, we not only disable
ATS support for the device, but we use Access Control Services (ACS)
Transaction Blocking to actively prevent devices from sending TLPs with
non-default AT field values.
Extend pci=noats to also make use of PCI_ACS_TB so that not only is ATS
disabled at the device, but blocked at the downstream ports. This provides
a means to further lock-down ATS for cases such as device assignment, where
it may not be the hardware configuration of the device that makes it
untrusted, but the driver running on the device.
Jakub Kicinski [Wed, 11 Aug 2021 18:59:55 +0000 (11:59 -0700)]
PCI/PTM: Remove error message at boot
Since 39850ed51062 ("PCI/PTM: Save/restore Precision Time Measurement
Capability for suspend/resume"), devices that have PTM capability but
don't enable it see this message on calls to pci_save_state():
no suspend buffer for PTM
Drop the message, it's perfectly fine not to use a capability.
Fixes: 39850ed51062 ("PCI/PTM: Save/restore Precision Time Measurement Capability for suspend/resume") Link: https://lore.kernel.org/r/20210811185955.3112534-1-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: David E. Box <david.e.box@linux.intel.com>
Heiner Kallweit [Fri, 20 Aug 2021 20:32:42 +0000 (15:32 -0500)]
PCI/VPD: Add pci_vpd_check_csum()
VPD checksum information and checksum calculation are specified by PCIe
r5.0, sec 6.28.2.2. Therefore checksum handling can and should be moved
into the PCI VPD core.
Add pci_vpd_check_csum() to validate the VPD checksum.
Heiner Kallweit [Wed, 18 Aug 2021 19:00:57 +0000 (21:00 +0200)]
PCI/VPD: Add pci_vpd_find_ro_info_keyword()
All users of pci_vpd_find_info_keyword() are interested in the VPD RO
section only. In addition all calls are followed by the same activities to
calculate start of tag data area and size of the data area.
Add pci_vpd_find_ro_info_keyword() that combines these functionalities.
pci_vpd_find_info_keyword() can be phased out once all users are converted.
Heiner Kallweit [Wed, 18 Aug 2021 18:59:31 +0000 (20:59 +0200)]
PCI/VPD: Add pci_vpd_alloc()
Several users of the VPD API use a fixed-size buffer and read the VPD into
it for further usage. This requires special handling for the case that the
buffer isn't big enough to hold the full VPD data. Also the buffer is
often allocated on the stack, which isn't too nice.
Add pci_vpd_alloc() to dynamically allocate buffer of the correct size and
read VPD into it.
Add driver for Intel Keem Bay SoC PCIe controller. This controller
is based on DesignWare PCIe core.
In Root Complex mode, only internal reference clock is possible for
Keem Bay A0. For Keem Bay B0, external reference clock can be used
and will be the default configuration. Currently, keembay_pcie_of_data
structure has one member. It will be expanded later to handle this
difference.
Endpoint mode link initialization is handled by the boot firmware.
Link: https://lore.kernel.org/r/20210805211010.29484-3-srikanth.thokala@intel.com Signed-off-by: Wan Ahmad Zainie <wan.ahmad.zainie.wan.mohamad@intel.com> Signed-off-by: Srikanth Thokala <srikanth.thokala@intel.com> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Reviewed-by: Krzysztof Wilczyński <kw@linux.com> Reviewed-by: Rob Herring <robh@kernel.org> Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
dt-bindings: PCI: Add Intel Keem Bay PCIe controller
Document DT bindings for PCIe controller found on Intel Keem Bay SoC.
Link: https://lore.kernel.org/r/20210805211010.29484-2-srikanth.thokala@intel.com Signed-off-by: Wan Ahmad Zainie <wan.ahmad.zainie.wan.mohamad@intel.com> Signed-off-by: Srikanth Thokala <srikanth.thokala@intel.com> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Reviewed-by: Rob Herring <robh@kernel.org>
Pali Rohár [Thu, 24 Jun 2021 21:55:45 +0000 (23:55 +0200)]
PCI: aardvark: Configure PCIe resources from 'ranges' DT property
In commit 6df6ba974a55 ("PCI: aardvark: Remove PCIe outbound window
configuration") was removed aardvark PCIe outbound window configuration and
commit description said that was recommended solution by HW designers.
But that commit completely removed support for configuring PCIe IO
resources without removing PCIe IO 'ranges' from DTS files. After that
commit PCIe IO space started to be treated as PCIe MEM space and accessing
it just caused kernel crash.
Moreover implementation of PCIe outbound windows prior that commit was
incorrect. It completely ignored offset between CPU address and PCIe bus
address and expected that in DTS is CPU address always same as PCIe bus
address without doing any checks. Also it completely ignored size of every
PCIe resource specified in 'ranges' DTS property and expected that every
PCIe resource has size 128 MB (also for PCIe IO range). Again without any
check. Apparently none of PCIe resource has in DTS specified size of 128
MB. So it was completely broken and thanks to how aardvark mask works,
configuration was completely ignored.
This patch reverts back support for PCIe outbound window configuration but
implementation is a new without issues mentioned above. PCIe outbound
window is required when DTS specify in 'ranges' property non-zero offset
between CPU and PCIe address space. To address recommendation by HW
designers as specified in commit description of 6df6ba974a55, set default
outbound parameters as PCIe MEM access without translation and therefore
for this PCIe 'ranges' it is not needed to configure PCIe outbound window.
For PCIe IO space is needed to configure aardvark PCIe outbound window.
This patch fixes kernel crash when trying to access PCIe IO space.
AM64 has the same PCIe IP as in J7200 with certain erratas not
applicable (quirk_detect_quiet_flag). Add support for "ti,am64-pcie-host"
compatible and "ti,am64-pcie-ep" compatible that is specific to AM64.
J7200 has the same PCIe IP as in J721E with minor changes in the
wrapper. J7200 allows byte access of bridge configuration space
registers and the register field for LINK_DOWN interrupt is different.
J7200 also requires "quirk_detect_quiet_flag" to be set. Configure these
changes as part of driver data applicable only to J7200.
Nadeem Athani [Wed, 11 Aug 2021 12:33:33 +0000 (18:03 +0530)]
PCI: cadence: Add quirk flag to set minimum delay in LTSSM Detect.Quiet state
PCIe fails to link up if SERDES lanes not used by PCIe are assigned to
another protocol. For example, link training fails if lanes 2 and 3 are
assigned to another protocol while lanes 0 and 1 are used for PCIe to
form a two lane link. This failure is due to an incorrect tie-off on an
internal status signal indicating electrical idle.
Status signals going from SERDES to PCIe Controller are tied-off when a
lane is not assigned to PCIe. Signal indicating electrical idle is
incorrectly tied-off to a state that indicates non-idle. As a result,
PCIe sees unused lanes to be out of electrical idle and this causes
LTSSM to exit Detect.Quiet state without waiting for 12ms timeout to
occur. If a receiver is not detected on the first receiver detection
attempt in Detect.Active state, LTSSM goes back to Detect.Quiet and
again moves forward to Detect.Active state without waiting for 12ms as
required by PCIe base specification. Since wait time in Detect.Quiet is
skipped, multiple receiver detect operations are performed back-to-back
without allowing time for capacitance on the transmit lines to
discharge. This causes subsequent receiver detection to always fail even
if a receiver gets connected eventually.
Add a quirk flag "quirk_detect_quiet_flag" to program the minimum
time the LTSSM should wait on entering Detect.Quiet state here.
This has to be set for J7200 as it has an incorrect tie-off on unused
lanes.
PCI: cadence: Use bitfield for *quirk_retrain_flag* instead of bool
No functional change. As we are intending to add additional 1-bit
members in struct j721e_pcie_data/struct cdns_pcie_rc, use bitfields
instead of bool since it takes less space. As discussed in [1],
the preference is to use bitfileds instead of bool inside structures.
_RST is a standard ACPI method that performs a function level reset of a
device (ACPI v6.3, sec 7.3.25).
Add pci_dev_acpi_reset() to probe for _RST method and execute if present.
The default priority of this reset is set to below device-specific and
above hardware resets.
Suggested-by: Alex Williamson <alex.williamson@redhat.com> Link: https://lore.kernel.org/r/20210817180500.1253-9-ameynarkhede03@gmail.com Signed-off-by: Shanker Donthineni <sdonthineni@nvidia.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Sinan Kaya <okaya@kernel.org> Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
However, things like pci_configure_device() and pci_init_capabilities()
that run before device_add() need the ACPI_COMPANION, e.g.,
acpi_pci_bridge_d3() uses a _DSD method to learn about D3 support. These
places had special-case code to manually look up the ACPI_COMPANION.
Set the ACPI_COMPANION earlier, in pci_setup_device(), so it will be
available while configuring the device. This covers both paths to creating
pci_dev objects:
pci_scan_single_device # for normal non-SR-IOV devices
pci_scan_device
pci_setup_device
pci_set_acpi_fwnode
pci_device_add
pci_iov_add_virtfn # for SR-IOV virtual functions
pci_setup_device
pci_set_acpi_fwnode
Amey Narkhede [Tue, 17 Aug 2021 18:04:55 +0000 (23:34 +0530)]
PCI: Remove reset_fn field from pci_dev
"reset_fn" indicates whether the device supports any reset mechanism.
Remove the use of reset_fn in favor of the reset_methods array that tracks
supported reset mechanisms of a device and their ordering.
The octeon driver incorrectly used reset_fn to detect whether the device
supports FLR or not. Use pcie_reset_flr() to probe whether it supports FLR.
Co-developed-by: Alex Williamson <alex.williamson@redhat.com> Link: https://lore.kernel.org/r/20210817180500.1253-5-ameynarkhede03@gmail.com Signed-off-by: Alex Williamson <alex.williamson@redhat.com> Signed-off-by: Amey Narkhede <ameynarkhede03@gmail.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Alex Williamson <alex.williamson@redhat.com> Reviewed-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Amey Narkhede [Tue, 17 Aug 2021 18:04:53 +0000 (23:34 +0530)]
PCI: Add pcie_reset_flr() with 'probe' argument
Most reset methods are of the form "pci_*_reset(dev, probe)". pcie_flr()
was an exception because it relied on a separate pcie_has_flr() function
instead of taking a "probe" argument.
Add "pcie_reset_flr(dev, probe)" to follow the convention. Remove
pcie_has_flr().
Some pcie_flr() callers that did not use pcie_has_flr() remain.
Hyper-V vPCI protocol version 1_4 adds support for create interrupt
v3. Create interrupt v3 essentially makes the size of the vector
field bigger in the message, thereby allowing bigger vector values.
For example, that will come into play for supporting LPI vectors
on ARM, which start at 8192.
Fixes: 45db33709ccc ("PCI: Allow specifying devices using a base bus and path of devfns") Link: https://lore.kernel.org/r/20210812070004.GC31863@kili Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Logan Gunthorpe <logang@deltatee.com>