Flush indirect branches when switching into a process that marked itself
non dumpable. This protects high value processes like gpg better,
without having too high performance overhead.
If done naïvely, we could switch to a kernel idle thread and then back
to the original process, such as:
process A -> idle -> process A
In such scenario, we do not have to do IBPB here even though the process
is non-dumpable, as we are switching back to the same process after a
hiatus.
To avoid the redundant IBPB, which is expensive, we track the last mm
user context ID. The cost is to have an extra u64 mm context id to track
the last mm we were using before switching to the init_mm used by idle.
Avoiding the extra IBPB is probably worth the extra memory for this
common scenario.
For those cases where tlb_defer_switch_to_init_mm() returns true (non
PCID), lazy tlb will defer switch to init_mm, so we will not be changing
the mm for the process A -> idle -> process A switch. So IBPB will be
skipped for this case.
Thanks to the reviewers and Andy Lutomirski for the suggestion of
using ctx_id which got rid of the problem of mm pointer recycling.
Signed-off-by: Tim Chen <tim.c.chen@linux.intel.com> Signed-off-by: David Woodhouse <dwmw@amazon.co.uk> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: ak@linux.intel.com Cc: karahmed@amazon.de Cc: arjan@linux.intel.com Cc: torvalds@linux-foundation.org Cc: linux@dominikbrodowski.net Cc: peterz@infradead.org Cc: bp@alien8.de Cc: luto@kernel.org Cc: pbonzini@redhat.com Cc: gregkh@linux-foundation.org Link: https://lkml.kernel.org/r/1517263487-3708-1-git-send-email-dwmw@amazon.co.uk
(backported from commit 18bf3c3ea8ece8f03b6fc58508f2dfd23c7711c7)
[tyhicks: Dropped the enhancement that tracked the last mm user context ID] Signed-off-by: Tyler Hicks <tyhicks@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Using a ptrace access check in the middle of a task switch was causing
a hard lockup in some cases when the old task was confined by AppArmor.
If the AppArmor policy for the the old task didn't allow the task to
ptrace the new task, AppArmor would attempt to emit an audit message and
deadlock on the task's pi_lock would occur. The fix is to revert this
change and go with upstream's implementation that uses the task's
dumpable state to determine if IBPB should be used.
Signed-off-by: Tyler Hicks <tyhicks@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Andy Whitcroft [Tue, 3 Apr 2018 16:52:00 +0000 (18:52 +0200)]
UBUNTU: [Packaging] include the retpoline extractor in the headers
BugLink: http://bugs.launchpad.net/bugs/1760876
Out of tree builds utilise the kernel Makefiles and therefore
we need to include all direct dependencies of those Makefiles.
Now that we call out to the repoline extractor during builds we
must carry the extractor with the headers. Move the extractor
to the kernel scripts directory and ensure its name is unique.
Signed-off-by: Andy Whitcroft <apw@canonical.com> Acked-by: Juerg Haefliger <juerg.haefliger@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com>
[ klebers: added fixup for commit message ] Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
UBUNTU: [Packaging] final-checks -- remove check for empty retpoline files
With the new support for removing known safe retpoline sequences
from the ones which were detected it is now completely valid to
end up with an empty retpoline file in the abi. Remove the
check for empty retpoline files so this will not cause an error.
BugLink: http://bugs.launchpad.net/bugs/1758856 Signed-off-by: Seth Forshee <seth.forshee@canonical.com> Signed-off-by: Andy Whitcroft <apw@canonical.com> Acked-by: Juerg Haefliger <juerg.haefliger@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
With CONFIG_KASAN, we get an overly long stack frame due to inlining
the register access functions:
drivers/media/tuners/r820t.c: In function 'generic_set_freq.isra.7':
drivers/media/tuners/r820t.c:1334:1: error: the frame size of 2880 bytes is larger than 2048 bytes [-Werror=frame-larger-than=]
This is caused by a gcc bug that has now been fixed in gcc-8.
To work around the problem, we can pass the register data
through a local variable that older gcc versions can optimize
out as well.
The ohci-hcd node has an interrupt number but no interrupt-parent,
leading to a warning with current dtc versions:
arch/arm/boot/dts/s5pv210-aquila.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/ohci@ec300000
arch/arm/boot/dts/s5pv210-goni.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/ohci@ec300000
arch/arm/boot/dts/s5pv210-smdkc110.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/ohci@ec300000
arch/arm/boot/dts/s5pv210-smdkv210.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/ohci@ec300000
arch/arm/boot/dts/s5pv210-torbreck.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/ohci@ec300000
As seen from the related exynos dts files, the ohci and ehci controllers
always share one interrupt number, and the number is the same here as
well, so setting the same interrupt-parent is the reasonable solution
here.
Normal pathname lookup doesn't allow empty pathnames, but using
AT_EMPTY_PATH (with name_to_handle_at() or fstatat(), for example) you
can trigger an empty pathname lookup.
And not only is the RCU lookup in that case entirely unnecessary
(because we'll obviously immediately finalize the end result), it is
actively wrong.
Why? An empth path is a special case that will return the original
'dirfd' dentry - and that dentry may not actually be RCU-free'd,
resulting in a potential use-after-free if we were to initialize the
path lazily under the RCU read lock and depend on complete_walk()
finalizing the dentry.
arch/x86/kernel/ldt.c: In function 'alloc_ldt_struct':
arch/x86/include/asm/pgtable_types.h:208:24: error: large integer implicitly truncated to unsigned type [-Werror=overflow]
#define __PAGE_KERNEL (__PAGE_KERNEL_EXEC | _PAGE_NX)
^
arch/x86/kernel/ldt.c:81:6: note: in expansion of macro '__PAGE_KERNEL'
__PAGE_KERNEL);
^~~~~~~~~~~~~
I originally ran into this last year when the patches were part of linux-next,
and tried to work around it by using the proper 'pteval_t' types consistently,
but that caused additional problems.
This takes a much simpler approach, and makes the argument type of the dummy
helper always 64-bit, which is wide enough for any page table layout and
won't hurt since this call is just an empty stub anyway.
dec_pending() is given an error status (possibly 0) to be recorded
against a bio. It can be called several times on the one 'struct
dm_io', and it is careful to only assign a non-zero error to
io->status. However when it then assigned io->status to bio->bi_status,
it is not careful and could overwrite a genuine error status with 0.
This can happen when chained bios are in use. If a bio is chained
beneath the bio that this dm_io is handling, the child bio might
complete and set bio->bi_status before the dm_io completes.
This has been possible since chained bios were introduced in 3.14, and
has become a lot easier to trigger with commit 18a25da84354 ("dm: ensure
bio submission follows a depth-first tree walk") as that commit caused
dm to start using chained bios itself.
A particular failure mode is that if a bio spans an 'error' target and a
working target, the 'error' fragment will complete instantly and set the
->bi_status, and the other fragment will normally complete a little
later, and will clear ->bi_status.
The fix is simply to only assign io_error to bio->bi_status when
io_error is not zero.
Reported-and-tested-by: Milan Broz <gmazyland@gmail.com> Cc: stable@vger.kernel.org (v3.14+) Signed-off-by: NeilBrown <neilb@suse.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Juerg Haefliger <juergh@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
ALSA sequencer core initializes the event pool on demand by invoking
snd_seq_pool_init() when the first write happens and the pool is
empty. Meanwhile user can reset the pool size manually via ioctl
concurrently, and this may lead to UAF or out-of-bound accesses since
the function tries to vmalloc / vfree the buffer.
A simple fix is to just wrap the snd_seq_pool_init() call with the
recently introduced client->ioctl_mutex; as the calls for
snd_seq_pool_init() from other side are always protected with this
mutex, we can avoid the race.
Add quirk to ensure a sync endpoint is properly configured.
This patch is a fix for same symptoms on Behringer UFX1204 as patch
from Albertto Aquirre on Dec 8 2016 for Axe-Fx II.
These laptops have a combined jack to attach headsets, the U727 on
the left, the U757 on the right, but a headsets microphone doesn't
work. Using hdajacksensetest I found that pin 0x19 changed the
present state when plugging the headset, in addition to 0x21, but
didn't have the correct configuration (shown as "Not connected").
So this sets the configuration to the same values as the headphone
pin 0x21 except for the device type microphone, which makes it
work correctly. With the patch the configured pins for U727 are
Pin 0x12 (Internal Mic, Mobile-In): present = No
Pin 0x14 (Internal Speaker): present = No
Pin 0x19 (Black Mic, Left side): present = No
Pin 0x1d (Internal Aux): present = No
Pin 0x21 (Black Headphone, Left side): present = No
The layout of the UAC2 Control request and response varies depending on
the request type. With the current implementation, only the Layout 2
Parameter Block (with the 2-byte sized RANGE attribute) is handled
properly. For the Control requests with the 1-byte sized RANGE attribute
(Bass Control, Mid Control, Tremble Control), the response is parsed
incorrectly.
This commit:
* fixes the wLength field value in the request
* fixes parsing the range values from the response
Fixes: 23caaf19b11e ("ALSA: usb-mixer: Add support for Audio Class v2.0") Signed-off-by: Kirill Marinushkin <k.marinushkin@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Juerg Haefliger <juergh@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The highest objectid, which is assigned to new inode, is decided at
the time of initializing fs roots. However, in cases where log replay
gets processed, the btree which fs root owns might be changed, so we
have to search it again for the highest objectid, otherwise creating
new inode would end up with -EEXIST.
cc: <stable@vger.kernel.org> v4.4-rc6+ Fixes: f32e48e92596 ("Btrfs: Initialize btrfs_root->highest_objectid when loading tree root and subvolume roots") Signed-off-by: Liu Bo <bo.li.liu@oracle.com> Reviewed-by: Josef Bacik <jbacik@fb.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Juerg Haefliger <juergh@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
In cases that the whole fs flips into readonly status due to failures in
critical sections, then log tree's blocks are still dirty, and this leads
to a crash during umount time, the crash is about use-after-free,
cc: <stable@vger.kernel.org> v3.12+ Fixes: 681ae50917df ("Btrfs: cleanup reserved space when freeing tree log on error") Signed-off-by: Liu Bo <bo.li.liu@oracle.com> Reviewed-by: Josef Bacik <jbacik@fb.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Juerg Haefliger <juergh@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
@cur_offset is not set back to what it should be (@cow_start) if
btrfs_next_leaf() returns something wrong, and the range [cow_start,
cur_offset) remains locked forever.
cc: <stable@vger.kernel.org> Signed-off-by: Liu Bo <bo.li.liu@oracle.com> Reviewed-by: Josef Bacik <jbacik@fb.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Juerg Haefliger <juergh@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
There has been a coding error in rtl8821ae since it was first introduced,
namely that an 8-bit register was read using a 16-bit read in
_rtl8821ae_dbi_read(). This error was fixed with commit 40b368af4b75
("rtlwifi: Fix alignment issues"); however, this change led to
instability in the connection. To restore stability, this change
was reverted in commit b8b8b16352cd ("rtlwifi: rtl8821ae: Fix connection
lost problem").
Unfortunately, the unaligned access causes machine checks in ARM
architecture, and we were finally forced to find the actual cause of the
problem on x86 platforms. Following a suggestion from Pkshih
<pkshih@realtek.com>, it was found that increasing the ASPM L1
latency from 0 to 7 fixed the instability. This parameter was varied to
see if a smaller value would work; however, it appears that 7 is the
safest value. A new symbol is defined for this quantity, thus it can be
easily changed if necessary.
Fixes: b8b8b16352cd ("rtlwifi: rtl8821ae: Fix connection lost problem") Cc: Stable <stable@vger.kernel.org> # 4.14+ Fix-suggested-by: Pkshih <pkshih@realtek.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Tested-by: James Cameron <quozl@laptop.org> # x86_64 OLPC NL3 Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Juerg Haefliger <juergh@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
When this method is set, the caller expects struct console_font fields
to be properly initialized when it returns. Leave it unset otherwise
nonsensical (leaked kernel stack) values are returned to user space.
Fix child-node lookup during probe, which ended up searching the whole
device tree depth-first starting at the parent rather than just matching
on its children.
To make things worse, the parent display node was also prematurely
freed.
Note that the display and timings node references are never put after a
successful dt-initialisation so the nodes would leak on later probe
deferrals and on driver unbind.
In the function __ext4_grp_locked_error(), __save_error_info()
is called to save error info in super block block, but does not sync
that information to disk to info the subsequence fsck after reboot.
This patch writes the error information to disk. After this patch,
I think there is no obvious EXT4 error handle branches which leads to
"Remounting filesystem read-only" will leave the disk partition miss
the subsequence fsck.
According to the OPAL docs:
skiboot-5.2.5/doc/opal-api/opal-rtc-read-3.txt
skiboot-5.2.5/doc/opal-api/opal-rtc-write-4.txt
OPAL_HARDWARE may be returned from OPAL_RTC_READ or OPAL_RTC_WRITE and
this indicates either a transient or permanent error.
Prior to this patch, Linux was not dealing with OPAL_HARDWARE being a
permanent error particularly well, in that you could end up in a busy
loop.
This was not too hard to trigger on an AMI BMC based OpenPOWER machine
doing a continuous "ipmitool mc reset cold" to the BMC, the result of
that being that we'd get stuck in an infinite loop in
opal_get_rtc_time().
We now retry a few times before returning the error higher up the
stack.
Fixes: 16b1d26e77b1 ("rtc/tpo: Driver to support rtc and wakeup on PowerNV platform") Cc: stable@vger.kernel.org # v3.19+ Signed-off-by: Stewart Smith <stewart@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Juerg Haefliger <juergh@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Currently, x86_cache_size is of type int, which makes no sense as we
will never have a valid cache size equal or less than 0. So instead of
initializing this variable to -1, it can perfectly be initialized to 0
and use it as an unsigned variable instead.
Suggested-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org>
Addresses-Coverity-ID: 1464429 Link: http://lkml.kernel.org/r/20180213192208.GA26414@embeddedor.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Juerg Haefliger <juergh@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
With retpoline, tight loops of "call this function for every XXX" are
very much pessimised by taking a prediction miss *every* time. This one
is by far the biggest contributor to the guest launch time with retpoline.
By marking the iterator slot_handle_…() functions always_inline, we can
ensure that the indirect function call can be optimised away into a
direct call and it actually generates slightly smaller code because
some of the other conditionals can get optimised away too.
Performance is now pretty close to what we see with nospectre_v2 on
the command line.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org> Tested-by: Filippo Sironi <sironi@amazon.de> Signed-off-by: David Woodhouse <dwmw@amazon.co.uk> Reviewed-by: Filippo Sironi <sironi@amazon.de> Acked-by: Paolo Bonzini <pbonzini@redhat.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Arjan van de Ven <arjan@linux.intel.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: David Woodhouse <dwmw2@infradead.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: arjan.van.de.ven@intel.com Cc: dave.hansen@intel.com Cc: jmattson@google.com Cc: karahmed@amazon.de Cc: kvm@vger.kernel.org Cc: rkrcmar@redhat.com Link: http://lkml.kernel.org/r/1518305967-31356-4-git-send-email-dwmw@amazon.co.uk Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Juerg Haefliger <juergh@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
We had another backport (e.g. 623e5c8ae32b in 4.4.115), but it applies
the new mutex also to the code paths that are invoked via faked
kernel-to-kernel ioctls. As reported recently, this leads to a
deadlock at suspend (or other scenarios triggering the kernel
sequencer client).
This patch addresses the issue by taking the mutex only in the code
paths invoked by user-space, just like the original fix patch does.
The "dmas" cells for the designware DMA controller need to have only 3
properties apart from the phandle: request line, src master and
destination master. But the commit 6e8887f60f60 updated it incorrectly
while moving from platform code to DT. Fix it.
The GPIO polarity is missing in the hdmi,hpd-gpio property, this
fixes the following DT warnings:
arch/arm/boot/dts/stih410-b2120.dtb: Warning (gpios_property): hdmi,hpd-gpio property
size (8) too small for cell size 2 in /soc/sti-display-subsystem/sti-hdmi@8d04000
arch/arm/boot/dts/stih407-b2120.dtb: Warning (gpios_property): hdmi,hpd-gpio property
size (8) too small for cell size 2 in /soc/sti-display-subsystem/sti-hdmi@8d04000
arch/arm/boot/dts/stih410-b2260.dtb: Warning (gpios_property): hdmi,hpd-gpio property
size (8) too small for cell size 2 in /soc/sti-display-subsystem/sti-hdmi@8d04000
[arnd: marked Cc:stable since this warning shows up with the latest dtc
by default, and is more likely to actually cause problems than the
other patches from this series]
For some reason, the implementation of some 16-bit ID system calls
(namely, setuid16/setgid16 and setfsuid16/setfsgid16) used type cast
instead of low2highgid/low2highuid macros for converting [GU]IDs, which
led to incorrect handling of value of -1 (which ought to be considered
invalid).
Propagate the error of devfreq_add_device() in devm_devfreq_add_device()
rather than statically returning ENOMEM. This makes it slightly faster
to pinpoint the cause of a returned error.
Fixes: 8cd84092d35e ("PM / devfreq: Add resource-managed function for devfreq device") Cc: stable@vger.kernel.org Acked-by: Chanwoo Choi <cw00.choi@samsung.com> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Juerg Haefliger <juergh@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Allocating steerable UD QPs depends on having at least one IB port,
while releasing those QPs does not.
As a result, when there are only ETH ports, the IB (RoCE) driver
requests releasing a qp range whose base qp is zero, with
qp count zero.
When SR-IOV is enabled, and the VF driver is running on a VM over
a hypervisor which treats such qp release calls as errors
(rather than NOPs), we see lines in the VM message log like:
mlx4_core 0002:00:02.0: Failed to release qp range base:0 cnt:0
Fix this by adding a check for a zero count in mlx4_release_qp_range()
(which thus treats releasing 0 qps as a nop), and eliminating the
check for device managed flow steering when releasing steerable UD QPs.
(Freeing ib_uc_qpns_bitmap unconditionally is also OK, since it
remains NULL when steerable UD QPs are not allocated).
Fixes: 4196670be786 ("IB/mlx4: Don't allocate range of steerable UD QPs for Ethernet-only device") Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Juerg Haefliger <juergh@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/1754584
Fix mmap'd libaio read on non-prefaulted page deadlock. This is a hot fix
from ZFS upstream that ensure pages do not deadlock and replaces the original
fix as it is a far better solution.
Performing a read with the target data in a mmap'd page that is map'd into
the same blocks that are being read causes a lock on the page and a further
lock on the same page when the page is being faulted in, causing deadlock.
This is an improved fix from the original fix which ensures the pages don't
deadlock and removes the original potentially racy pre-faulting fix
Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Colin Ian King [Wed, 28 Mar 2018 15:44:00 +0000 (17:44 +0200)]
UBUNTU: SAUCE: (noup) zfs to 0.6.5.6-0ubuntu19
BugLink: https://bugs.launchpad.net/bugs/1754584
Add ZFS 0.7.0 kernel ioctl binary compat shim, detect ZFS kernel driver
version and copy zfs ioctl command to the newer ZFS 0.7.0 ioctl command
layout.
This patch sync's the kernel drivers to the module fixes in userspace,
introduced in version zfsutils-linux 0.6.5.6-0ubuntu19. No functional
change in the kernel drivers; this just adds compat structures to allow
userspace to copy ioctl data appropriately in the userspace tools.
Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
John Johansen [Tue, 13 Mar 2018 20:48:00 +0000 (21:48 +0100)]
UBUNTU: SAUCE: apparmor: fix bad __initdata tagging on, apparmor_initialized
BugLink: http://bugs.launchpad.net/bugs/1758471
apparmor_initialized is no longer init only data and the __initdata
tagging was removed from the variable definition in
security/apparmor/lsm.c but missed being removed from the declaration
in security/apparmor/include/lib.h
resulting in the following build warning
WARNING: vmlinux.o(.text+0x393a60): Section mismatch in reference from the function param_set_aauint() to the variable .init.data:apparmor_initialized
Signed-off-by: John Johansen <john.johansen@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
__unregister_ftrace_function_probe() will incorrectly parse the glob filter
because it resets the search variable that was setup by filter_parse_regex().
Al Viro reported this:
After that call of filter_parse_regex() we could have func_g.search not
equal to glob only if glob started with '!' or '*'. In the former case
we would've buggered off with -EINVAL (not = 1). In the latter we
would've set func_g.search equal to glob + 1, calculated the length of
that thing in func_g.len and proceeded to reset func_g.search back to
glob.
Suppose the glob is e.g. *foo*. We end up with
func_g.type = MATCH_MIDDLE_ONLY;
func_g.len = 3;
func_g.search = "*foo";
Feeding that to ftrace_match_record() will not do anything sane - we
will be looking for names containing "*foo" (->len is ignored for that
one).
Setting si_code to 0 is the same a setting si_code to SI_USER which is definitely
not correct. With si_code set to SI_USER si_pid and si_uid will be copied to
userspace instead of si_addr. Which is very wrong.
So fix this by using a sensible si_code (SEGV_MAPERR) for this failure.
Fixes: b920de1b77b7 ("mn10300: add the MN10300/AM33 architecture to the kernel") Cc: David Howells <dhowells@redhat.com> Cc: Masakazu Urade <urade.masakazu@jp.panasonic.com> Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com> Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Juerg Haefliger <juergh@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
As a writable mount, it is not expected for overlayfs to return
EINVAL/EROFS for fsync, even if dir/file is not changed.
This commit fixes the case of fsync of directory, which is easier to
address, because overlayfs already implements fsync file operation for
directories.
The problem reported by Raphael is that new PostgreSQL 10.0 with a
database in overlayfs where lower layer in squashfs fails to start.
The failure is due to fsync error, when PostgreSQL does fsync on all
existing db directories on startup and a specific directory exists
lower layer with no changes.
There's no need to be printing a raw kernel pointer to the kernel log at
every boot. So just remove it, and change the whole message to use the
correct dev_info() call at the same time.
Reported-by: Wang Qize <wang_qize@venustech.com.cn> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Juerg Haefliger <juergh@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
This function was introduced by 247e743cbe6e ("Btrfs: Use async helpers
to deal with pages that have been improperly dirtied") and it didn't do
any error handling then. This function might very well fail in ENOMEM
situation, yet it's not handled, this could lead to inconsistent state.
So let's handle the failure by setting the mapping error bit.
Signed-off-by: Nikolay Borisov <nborisov@suse.com> Reviewed-by: Qu Wenruo <wqu@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Juerg Haefliger <juergh@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Commit 523e1d399ce0 ("block: make gendisk hold a reference to its queue")
modified add_disk() and disk_release() but did not update any of the
error paths that trigger a put_disk() call after disk->queue has been
assigned. That introduced the following behavior in the pktcdvd driver
if pkt_new_dev() fails:
Since disk_release() calls blk_put_queue() anyway if disk->queue != NULL,
fix this by removing the blk_cleanup_queue() call from the pkt_setup_dev()
error path.
Fixes: commit 523e1d399ce0 ("block: make gendisk hold a reference to its queue") Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com> Cc: Tejun Heo <tj@kernel.org> Cc: Maciej S. Szmigiero <mail@maciej.szmigiero.name> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Juerg Haefliger <juergh@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Fix an uninitialized variable warning in the Octeon EDAC driver, as seen
in MIPS cavium_octeon_defconfig builds since v4.14 with Codescape GNU
Tools 2016.05-03:
drivers/edac/octeon_edac-lmc.c In function ‘octeon_lmc_edac_poll_o2’:
drivers/edac/octeon_edac-lmc.c:87:24: warning: ‘((long unsigned int*)&int_reg)[1]’ may \
be used uninitialized in this function [-Wmaybe-uninitialized]
if (int_reg.s.sec_err || int_reg.s.ded_err) {
^
Iinitialise the whole int_reg variable to zero before the conditional
assignments in the error injection case.
Return 0 if the operation was successful, not the userspace memory
value. Check that userspace value equals passed oldval, not itself.
Don't update *uval if the value wasn't read from userspace memory.
This fixes process hang due to infinite loop in futex_lock_pi.
It also fixes a bunch of glibc tests nptl/tst-mutexpi*.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Juerg Haefliger <juergh@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
On alpha, a process will crash if it attempts to start a thread and a
signal is delivered at the same time. The crash can be reproduced with
this program: https://cygwin.com/ml/cygwin/2014-11/msg00473.html
The reason for the crash is this:
* we call the clone syscall
* we go to the function copy_process
* copy process calls copy_thread_tls, it is a wrapper around copy_thread
* copy_thread sets the tls pointer: childti->pcb.unique = regs->r20
* copy_thread sets regs->r20 to zero
* we go back to copy_process
* copy process checks "if (signal_pending(current))" and returns
-ERESTARTNOINTR
* the clone syscall is restarted, but this time, regs->r20 is zero, so
the new thread is created with zero tls pointer
* the new thread crashes in start_thread when attempting to access tls
The comment in the code says that setting the register r20 is some
compatibility with OSF/1. But OSF/1 doesn't use the CLONE_SETTLS flag, so
we don't have to zero r20 if CLONE_SETTLS is set. This patch fixes the bug
by zeroing regs->r20 only if CLONE_SETTLS is not set.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Matt Turner <mattst88@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Juerg Haefliger <juergh@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
While reviewing the signal sending on openrisc the do_unaligned_access
function stood out because it is obviously wrong. A comment about an
si_code set above when actually si_code is never set. Leading to a
random si_code being sent to userspace in the event of an unaligned
access.
Looking further SIGBUS BUS_ADRALN is the proper pair of signal and
si_code to send for an unaligned access. That is what other
architectures do and what is required by posix.
Given that do_unaligned_access is broken in a way that no one can be
relying on it on openrisc fix the code to just do the right thing.
Commit 7d06d5895c15 ("Revert "Bluetooth: btusb: fix QCA...suspend/resume"")
removed the setting of the BTUSB_RESET_RESUME quirk for QCA Rome devices,
instead favoring adding USB_QUIRK_RESET_RESUME quirks in usb/core/quirks.c.
This was done because the DIY BTUSB_RESET_RESUME reset-resume handling
has several issues (see the original commit message). An added advantage
of moving over to the USB-core reset-resume handling is that it also
disables autosuspend for these devices, which is similarly broken on these.
But there are 2 issues with this approach:
1) It leaves the broken DIY BTUSB_RESET_RESUME code in place for Realtek
devices.
2) Sofar only 2 of the 10 QCA devices known to the btusb code have been
added to usb/core/quirks.c and if we fix the Realtek case the same way
we need to add an additional 14 entries. So in essence we need to
duplicate a large part of the usb_device_id table in btusb.c in
usb/core/quirks.c and manually keep them in sync.
This commit instead restores setting a reset-resume quirk for QCA devices
in the btusb.c code, avoiding the duplicate usb_device_id table problem.
This commit avoids the problems with the original DIY BTUSB_RESET_RESUME
code by simply setting the USB_QUIRK_RESET_RESUME quirk directly on the
usb_device.
This commit also moves the BTUSB_REALTEK case over to directly setting the
USB_QUIRK_RESET_RESUME on the usb_device and removes the now unused
BTUSB_RESET_RESUME code.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1514836 Fixes: 7d06d5895c15 ("Revert "Bluetooth: btusb: fix QCA...suspend/resume"") Cc: Leif Liddy <leif.linux@gmail.com> Cc: Matthias Kaehlcke <mka@chromium.org> Cc: Brian Norris <briannorris@chromium.org> Cc: Daniel Drake <drake@endlessm.com> Cc: Kai-Heng Feng <kai.heng.feng@canonical.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Juerg Haefliger <juergh@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
BCM43341 devices soldered onto the PCB (non-removable) always (AFAICT)
use an UART connection for bluetooth. But they also advertise btsdio
support on their 3th sdio function, this causes 2 problems:
1) A non functioning BT HCI getting registered
2) Since the btsdio driver does not have suspend/resume callbacks,
mmc_sdio_pre_suspend will return -ENOSYS, causing mmc_pm_notify()
to react as if the SDIO-card is removed and since the slot is
marked as non-removable it will never get detected as inserted again.
Which results in wifi no longer working after a suspend/resume.
This commit fixes both by making btsdio ignore BCM43341 devices
when connected to a slot which is marked non-removable.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Juerg Haefliger <juergh@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The Toshiba Click Mini uses an i2c attached keyboard/touchpad combo
(single i2c_hid device for both) which has a vid:pid of 04F3:0401,
which is also used by a bunch of Elan touchpads which are handled by the
drivers/input/mouse/elan_i2c driver, but that driver deals with pure
touchpads and does not work for a combo device such as the one on the
Toshiba Click Mini.
The combo on the Mini has an ACPI id of ELAN0800, which is not claimed
by the elan_i2c driver, so check for that and if it is found do not ignore
the device. This fixes the keyboard/touchpad combo on the Mini not working
(although with the touchpad in mouse emulation mode).
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Juerg Haefliger <juergh@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
This reverts commit 92266d6ef60c ("async: simplify lowest_in_progress()")
which was simply wrong: In the case where domain is NULL, we now use the
wrong offsetof() in the list_first_entry macro, so we don't actually
fetch the ->cookie value, but rather the eight bytes located
sizeof(struct list_head) further into the struct async_entry.
On 64 bit, that's the data member, while on 32 bit, that's a u64 built
from func and data in some order.
I think the bug happens to be harmless in practice: It obviously only
affects callers which pass a NULL domain, and AFAICT the only such
caller is
and the ASYNC_COOKIE_MAX means that in practice we end up waiting for
the async_global_pending list to be empty - but it would break if
somebody happened to pass (void*)-1 as the data element to
async_schedule, and of course also if somebody ever does a
async_synchronize_cookie_domain(, NULL) with a "finite" cookie value.
Maybe the "harmless in practice" means this isn't -stable material. But
I'm not completely confident my quick git grep'ing is enough, and there
might be affected code in one of the earlier kernels that has since been
removed, so I'll leave the decision to the stable guys.
Link: http://lkml.kernel.org/r/20171128104938.3921-1-linux@rasmusvillemoes.dk Fixes: 92266d6ef60c "async: simplify lowest_in_progress()" Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> Acked-by: Tejun Heo <tj@kernel.org> Cc: Arjan van de Ven <arjan@linux.intel.com> Cc: Adam Wallis <awallis@codeaurora.org> Cc: Lai Jiangshan <laijs@cn.fujitsu.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Juerg Haefliger <juergh@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When the watchdog device is suspended, its timeout is set to the maximum
value. During resume, the previously set timeout should be restored.
This does not work at the moment.
The suspend function calls
imx2_wdt_set_timeout(wdog, IMX2_WDT_MAX_TIME);
and resume reverts this by calling
imx2_wdt_set_timeout(wdog, wdog->timeout);
However, imx2_wdt_set_timeout() updates wdog->timeout. Therefore,
wdog->timeout is set to IMX2_WDT_MAX_TIME when we enter the resume
function.
Fix this by adding a new function __imx2_wdt_set_timeout() which
only updates the hardware settings. imx2_wdt_set_timeout() now calls
__imx2_wdt_set_timeout() and then saves the new timeout to
wdog->timeout.
During suspend, we call __imx2_wdt_set_timeout() directly so that
wdog->timeout won't be updated and we can restore the previous value
during resume. This approach makes wdog->timeout different from the
actual setting in the hardware which is usually not a good thing.
However, the two differ only while we're suspended and no kernel code is
running, so it should be ok in this case.
Signed-off-by: Martin Kaiser <martin@kaiser.cx> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@iguana.be> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Juerg Haefliger <juergh@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Consider the following scenario:
1. CPU A calls vmx_deliver_nested_posted_interrupt() to send an IPI
to CPU B via virtual posted-interrupt mechanism.
2. CPU B is currently executing L2 guest.
3. vmx_deliver_nested_posted_interrupt() calls
kvm_vcpu_trigger_posted_interrupt() which will note that
vcpu->mode == IN_GUEST_MODE.
4. Assume that before CPU A sends the physical POSTED_INTR_NESTED_VECTOR
IPI, CPU B exits from L2 to L0 during event-delivery
(valid IDT-vectoring-info).
5. CPU A now sends the physical IPI. The IPI is received in host and
it's handler (smp_kvm_posted_intr_nested_ipi()) does nothing.
6. Assume that before CPU A sets pi_pending=true and KVM_REQ_EVENT,
CPU B continues to run in L0 and reach vcpu_enter_guest(). As
KVM_REQ_EVENT is not set yet, vcpu_enter_guest() will continue and resume
L2 guest.
7. At this point, CPU A sets pi_pending=true and KVM_REQ_EVENT but
it's too late! CPU B already entered L2 and KVM_REQ_EVENT will only be
consumed at next L2 entry!
Another scenario to consider:
1. CPU A calls vmx_deliver_nested_posted_interrupt() to send an IPI
to CPU B via virtual posted-interrupt mechanism.
2. Assume that before CPU A calls kvm_vcpu_trigger_posted_interrupt(),
CPU B is at L0 and is about to resume into L2. Further assume that it is
in vcpu_enter_guest() after check for KVM_REQ_EVENT.
3. At this point, CPU A calls kvm_vcpu_trigger_posted_interrupt() which
will note that vcpu->mode != IN_GUEST_MODE. Therefore, do nothing and
return false. Then, will set pi_pending=true and KVM_REQ_EVENT.
4. Now CPU B continue and resumes into L2 guest without processing
the posted-interrupt until next L2 entry!
To fix both issues, we just need to change
vmx_deliver_nested_posted_interrupt() to set pi_pending=true and
KVM_REQ_EVENT before calling kvm_vcpu_trigger_posted_interrupt().
It will fix the first scenario by chaging step (6) to note that
KVM_REQ_EVENT and pi_pending=true and therefore process
nested posted-interrupt.
It will fix the second scenario by two possible ways:
1. If kvm_vcpu_trigger_posted_interrupt() is called while CPU B has changed
vcpu->mode to IN_GUEST_MODE, physical IPI will be sent and will be received
when CPU resumes into L2.
2. If kvm_vcpu_trigger_posted_interrupt() is called while CPU B hasn't yet
changed vcpu->mode to IN_GUEST_MODE, then after CPU B will change
vcpu->mode it will call kvm_request_pending() which will return true and
therefore force another round of vcpu_enter_guest() which will note that
KVM_REQ_EVENT and pi_pending=true and therefore process nested
posted-interrupt.
Fixes: 705699a13994 ("KVM: nVMX: Enable nested posted interrupt processing") Signed-off-by: Liran Alon <liran.alon@oracle.com> Reviewed-by: Nikita Leshenko <nikita.leshchenko@oracle.com> Reviewed-by: Krish Sadhukhan <krish.sadhukhan@oracle.com>
[Add kvm_vcpu_kick to also handle the case where L1 doesn't intercept L2 HLT
and L2 executes HLT instruction. - Paolo] Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Radim Krčmář <rkrcmar@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Juerg Haefliger <juergh@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
KVM doesn't follow the SMCCC when it comes to unimplemented calls,
and inject an UNDEF instead of returning an error. Since firmware
calls are now used for security mitigation, they are becoming more
common, and the undef is counter productive.
Instead, let's follow the SMCCC which states that -1 must be returned
to the caller when getting an unknown function number.
The 32-bit compat v4l2 ioctl handling is implemented based on its 64-bit
equivalent. It converts 32-bit data structures into its 64-bit
equivalents and needs to provide the data to the 64-bit ioctl in user
space memory which is commonly allocated using
compat_alloc_user_space().
However, due to how that function is implemented, it can only be called
a single time for every syscall invocation.
Supposedly to avoid this limitation, the existing code uses a mix of
memory from the kernel stack and memory allocated through
compat_alloc_user_space().
Under normal circumstances, this would not work, because the 64-bit
ioctl expects all pointers to point to user space memory. As a
workaround, set_fs(KERNEL_DS) is called to temporarily disable this
extra safety check and allow kernel pointers. However, this might
introduce a security vulnerability: The result of the 32-bit to 64-bit
conversion is writeable by user space because the output buffer has been
allocated via compat_alloc_user_space(). A malicious user space process
could then manipulate pointers inside this output buffer, and due to the
previous set_fs(KERNEL_DS) call, functions like get_user() or put_user()
no longer prevent kernel memory access.
The new approach is to pre-calculate the total amount of user space
memory that is needed, allocate it using compat_alloc_user_space() and
then divide up the allocated memory to accommodate all data structures
that need to be converted.
An alternative approach would have been to retain the union type karg
that they allocated on the kernel stack in do_video_ioctl(), copy all
data from user space into karg and then back to user space. However, we
decided against this approach because it does not align with other
compat syscall implementations. Instead, we tried to replicate the
get_user/put_user pairs as found in other places in the kernel:
if (get_user(clipcount, &up->clipcount) ||
put_user(clipcount, &kp->clipcount)) return -EFAULT;
Clearly nobody could be bothered to upstream this patch or at minimum
tell us :-( We only heard about this a week ago.
This patch was rebased and cleaned up. Compared to the original I
also swapped the order of the convert_in_user arguments so that they
matched copy_in_user. It was hard to review otherwise. I also replaced
the ALLOC_USER_SPACE/ALLOC_AND_GET by a normal function.
Fixes: 6b5a9492ca ("v4l: introduce string control support.") Signed-off-by: Daniel Mentz <danielmentz@google.com> Co-developed-by: Hans Verkuil <hans.verkuil@cisco.com> Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Juerg Haefliger <juergh@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Some ioctls need to copy back the result even if the ioctl returned
an error. However, don't do this for the error code -ENOTTY.
It makes no sense in that cases.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Juerg Haefliger <juergh@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
There is nothing wrong with using an unknown buffer type. So
stop spamming the kernel log whenever this happens. The kernel
will just return -EINVAL to signal this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Juerg Haefliger <juergh@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Commit b2787845fb91 ("V4L/DVB (5289): Add support for video output
overlays.") added the field global_alpha to struct v4l2_window but did
not update the compat layer accordingly. This change adds global_alpha
to struct v4l2_window32 and copies the value for global_alpha back and
forth.
Signed-off-by: Daniel Mentz <danielmentz@google.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Juerg Haefliger <juergh@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
If the device is of type VFL_TYPE_SUBDEV then vdev->ioctl_ops
is NULL so the 'if (!ops->vidioc_query_ext_ctrl)' check would crash.
Add a test for !ops to the condition.
All sub-devices that have controls will use the control framework,
so they do not have an equivalent to ops->vidioc_query_ext_ctrl.
Returning false if ops is NULL is the correct thing to do here.
ctrl_is_pointer just hardcoded two known string controls, but that
caused problems when using e.g. custom controls that use a pointer
for the payload.
Reimplement this function: it now finds the v4l2_ctrl (if the driver
uses the control framework) or it calls vidioc_query_ext_ctrl (if the
driver implements that directly).
In both cases it can now check if the control is a pointer control
or not.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Juerg Haefliger <juergh@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Instead of doing sizeof(struct foo) use sizeof(*up). There even were
cases where 4 * sizeof(__u32) was used instead of sizeof(kp->reserved),
which is very dangerous when the size of the reserved array changes.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Juerg Haefliger <juergh@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
We are under rcu read lock protection at that point:
rcu_read_lock();
d = atomic_long_read(&ns->stashed);
if (!d)
goto slow;
dentry = (struct dentry *)d;
if (!lockref_get_not_dead(&dentry->d_lockref))
goto slow;
rcu_read_unlock();
but don't use a proper RCU API on the free path, therefore a parallel
__d_free() could free it at the same time. We need to mark the stashed
dentry with DCACHE_RCUACCESS so that __d_free() will be called after all
readers leave RCU.
Fixes: e149ed2b805f ("take the targets of /proc/*/ns/* symlinks to separate fs") Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Andrew Morton <akpm@linux-foundation.org> Reported-by: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Eric Biggers <ebiggers3@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Juerg Haefliger <juergh@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Since Poly1305 requires a nonce per invocation, the Linux kernel
implementations of Poly1305 don't use the crypto API's keying mechanism
and instead expect the key and nonce as the first 32 bytes of the data.
But ->setkey() is still defined as a stub returning an error code. This
prevents Poly1305 from being used through AF_ALG and will also break it
completely once we start enforcing that all crypto API users (not just
AF_ALG) call ->setkey() if present.
Fix it by removing crypto_poly1305_setkey(), leaving ->setkey as NULL.
Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Juerg Haefliger <juergh@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When the cryptd template is used to wrap an unkeyed hash algorithm,
don't install a ->setkey() method to the cryptd instance. This change
is necessary for cryptd to keep working with unkeyed hash algorithms
once we start enforcing that ->setkey() is called when present.
Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Juerg Haefliger <juergh@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>