netfilter: flowtable: use dev_fill_forward_path() to obtain ingress device
Obtain the ingress device in the tuple from the route in the reply
direction. Use dev_fill_forward_path() instead to get the real ingress
device for this flow.
Fall back to use the ingress device that the IP forwarding route
provides if:
- dev_fill_forward_path() finds no real ingress device.
- the ingress device that is obtained is not part of the flowtable
devices.
- this route has a xfrm policy.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Add the xmit_type field that defines the two supported xmit paths in the
flowtable data plane, which are the neighbour and the xfrm xmit paths.
This patch prepares for new flowtable xmit path types to come.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Felix Fietkau [Wed, 24 Mar 2021 01:30:37 +0000 (02:30 +0100)]
net: dsa: resolve forwarding path for dsa slave ports
Add .ndo_fill_forward_path for dsa slave port devices
Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Felix Fietkau [Wed, 24 Mar 2021 01:30:36 +0000 (02:30 +0100)]
net: ppp: resolve forwarding path for bridge pppoe devices
Pass on the PPPoE session ID, destination hardware address and the real
device.
Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Felix Fietkau [Wed, 24 Mar 2021 01:30:35 +0000 (02:30 +0100)]
net: bridge: resolve forwarding path for VLAN tag actions in bridge devices
Depending on the VLAN settings of the bridge and the port, the bridge can
either add or remove a tag. When vlan filtering is enabled, the fdb lookup
also needs to know the VLAN tag/proto for the destination address
To provide this, keep track of the stack of VLAN tags for the path in the
lookup context
Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net>
For packets going through IP forwarding to eth0.100 whose destination
MAC address is ab:cd:ef:ab:cd:ef, dev_fill_forward_path() provides the
following path:
eth0.100 -> eth0
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net>
net: resolve forwarding path from virtual netdevice and HW destination address
This patch adds dev_fill_forward_path() which resolves the path to reach
the real netdevice from the IP forwarding side. This function takes as
input the netdevice and the destination hardware address and it walks
down the devices calling .ndo_fill_forward_path() for each device until
the real device is found.
where eth1 and eth2 are bridge ports and eth0 provides WAN connectivity.
ethX is the interface in another box which is connected to the eth1
bridge port.
For packets going through IP forwarding to br0 whose destination MAC
address is ab:cd:ef:ab:cd:ef, dev_fill_forward_path() provides the
following path:
br0 -> eth1
.ndo_fill_forward_path for br0 looks up at the FDB for the bridge port
from the destination MAC address to get the bridge port eth1.
This information allows to create a fast path that bypasses the classic
bridge and IP forwarding paths, so packets go directly from the bridge
port eth1 to eth0 (wan interface) and vice versa.
Colin Ian King [Wed, 24 Mar 2021 15:09:50 +0000 (15:09 +0000)]
net: bridge: Fix missing return assignment from br_vlan_replay_one call
The call to br_vlan_replay_one is returning an error return value but
this is not being assigned to err and the following check on err is
currently always false because err was initialized to zero. Fix this
by assigning err.
Addresses-Coverity: ("'Constant' variable guards dead code") Fixes: 22f67cdfae6a ("net: bridge: add helper to replay VLANs installed on port") Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 24 Mar 2021 19:14:08 +0000 (12:14 -0700)]
Merge branch 'bridge-mrp-next'
Horatiu Vultur says:
====================
bridge: mrp: Disable roles before deleting
The first patch in this series make sures that the driver is notified
that the role is disabled before the MRP instance is deleted. The
second patch uses this so it can simplify the driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Horatiu Vultur [Tue, 23 Mar 2021 08:33:47 +0000 (09:33 +0100)]
net: ocelot: Simplify MRP deletion
Now that the driver will always be notified that the role is deleted
before the ring is deleted, then we don't need to duplicate the logic of
cleaning the resources also in the delete function.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Horatiu Vultur [Tue, 23 Mar 2021 08:33:46 +0000 (09:33 +0100)]
bridge: mrp: Disable roles before deleting the MRP instance
When an MRP instance was created, the driver was notified that the
instance is created and then in a different callback about role of the
instance. But when the instance was deleted the driver was notified only
that the MRP instance is deleted and not also that the role is disabled.
This patch make sure that the driver is notified that the role is
changed to disabled before the MRP instance is deleted to have similar
callbacks with the creating of the instance. In this way it would
simplify the logic in the drivers.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
There are some variables in HNS driver will not being referenced
before assigned, so there is no need to init them.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yonglong Liu [Tue, 23 Mar 2021 07:41:08 +0000 (15:41 +0800)]
net: hns: remove unnecessary !! operation in hns_mac_config_sds_loopback_acpi()
The !! operation of variable en in hns_mac_config_sds_loopback_acpi()
is redundant, so remove it.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Vyukov [Tue, 23 Mar 2021 06:49:23 +0000 (07:49 +0100)]
net: make unregister netdev warning timeout configurable
netdev_wait_allrefs() issues a warning if refcount does not drop to 0
after 10 seconds. While 10 second wait generally should not happen
under normal workload in normal environment, it seems to fire falsely
very often during fuzzing and/or in qemu emulation (~10x slower).
At least it's not possible to understand if it's really a false
positive or not. Automated testing generally bumps all timeouts
to very high values to avoid flake failures.
Add net.core.netdev_unregister_timeout_secs sysctl to make
the timeout configurable for automated testing systems.
Lowering the timeout may also be useful for e.g. manual bisection.
The default value matches the current behavior.
Signed-off-by: Dmitry Vyukov <dvyukov@google.com> Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=211877 Cc: netdev@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Elder [Tue, 23 Mar 2021 01:05:05 +0000 (20:05 -0500)]
net: ipa: avoid 64-bit modulus
It is possible for a 32 bit x86 build to use a 64 bit DMA address.
There are two remaining spots where the IPA driver does a modulo
operation to check alignment of a DMA address, and under certain
conditions this can lead to a build error on i386 (at least).
The alignment checks we're doing are for power-of-2 values, and this
means the lower 32 bits of the DMA address can be used. This ensures
both operands to the modulo operator are 32 bits wide.
Reported-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Alex Elder <elder@linaro.org> Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 24 Mar 2021 00:13:04 +0000 (17:13 -0700)]
Merge branch '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
100GbE Intel Wired LAN Driver Updates 2021-03-23
This series contains updates to ice, fm10k, i40e, iavf, ixgbe, ixgbevf,
igb, e1000e, and e1000 drivers.
Tony fixes prototype warnings for mismatched header for ice driver.
Sasha fixes prototype warnings for mismatched header for igc and e1000e
driver.
Jesse fixes prototype warnings for mismatched header for the remaining
Intel drivers: fm10k, i40e, iavf, igb, ixgbe, and ixgbevf.
Gustavo A. R. Silva explicitly adds a break instead of falling through
in preparation of -Wimplicit-fallthrough for Clang to ice, fm10k,
ixgbe, igb, ixgbevf, and e1000 drivers,
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 23 Mar 2021 21:49:06 +0000 (14:49 -0700)]
Merge branch 'bridge-dsa-sandwiched-LAG'
Vladimir Oltean says:
====================
Better support for sandwiched LAGs with bridge and DSA
Changes in v4:
- Added missing EXPORT_SYMBOL_GPL
- Using READ_ONCE(fdb->dst)
- Split patches into (a) adding the bridge helpers (b) making DSA use them
- br_mdb_replay went back to the v1 approach where it allocated memory
in atomic context
- Created a br_switchdev_mdb_populate which reduces some of the code
duplication
- Fixed the error message in dsa_port_clear_brport_flags
- Replaced "dsa_port_vlan_filtering(dp, br, extack)" with
"dsa_port_vlan_filtering(dp, br_vlan_enabled(br), extack)" (duh)
- Added review tags (sorry if I missed any)
The objective of this series is to make LAG uppers on top of switchdev
ports work regardless of which order we link interfaces to their masters
(first make the port join the LAG, then the LAG join the bridge, or the
other way around).
There was a design decision to be made in patches 2-4 on whether we
should adopt the "push" model (which attempts to solve the problem
centrally, in the bridge layer) where the driver just calls:
and the bridge just replays the entire collection of switchdev port
attributes and objects that it has, in some predefined order and with
some predefined error handling logic;
or the "pull" model (which attempts to solve the problem by giving the
driver the rope to hang itself), where the driver, apart from calling:
(not necessarily all of them, and not necessarily in this order, and
with driver-defined error handling).
Even though I'm not in love myself with the "pull" model, I chose it
because there is a fundamental trick with replaying switchdev events
like this:
ip link add br0 type bridge
ip link add bond0 type bond
ip link set bond0 master br0
ip link set swp0 master bond0 <- this will replay the objects once for
the bond0 bridge port, and the swp0
switchdev port will process them
ip link set swp1 master bond0 <- this will replay the objects again for
the bond0 bridge port, and the swp1
switchdev port will see them, but swp0
will see them for the second time now
Basically I believe that it is implementation defined whether the driver
wants to error out on switchdev objects seen twice on a port, and the
bridge should not enforce a certain model for that. For example, for FDB
entries added to a bonding interface, the underling switchdev driver
might have an abstraction for just that: an FDB entry pointing towards a
logical (as opposed to physical) port. So when the second port joins the
bridge, it doesn't realy need to replay FDB entries, since there is
already at least one hardware port which has been receiving those
events, and the FDB entries don't need to be added a second time to the
same logical port.
In the other corner, we have the drivers that handle switchdev port
attributes on a LAG as individual switchdev port attributes on physical
ports (example: VLAN filtering). In fact, the switchdev_handle_port_attr_set
helper facilitates this: it is a fan-out from a single orig_dev towards
multiple lowers that pass the check_cb().
But that's the point: switchdev_handle_port_attr_set is just a helper
which the driver _opts_ to use. The bridge can't enforce the "push"
model, because that would assume that all drivers handle port attributes
in the same way, which is probably false.
For this reason, I preferred to go with the "pull" mode for this patch
set. Just to see how bad it is for other switchdev drivers to copy-paste
this logic, I added the pull support to ocelot too, and I think it's
pretty manageable.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Mon, 22 Mar 2021 23:51:52 +0000 (01:51 +0200)]
net: ocelot: replay switchdev events when joining bridge
The premise of this change is that the switchdev port attributes and
objects offloaded by ocelot might have been missed when we are joining
an already existing bridge port, such as a bonding interface.
The patch pulls these switchdev attributes and objects from the bridge,
on behalf of the 'bridge port' net device which might be either the
ocelot switch interface, or the bonding upper interface.
The ocelot_net.c belongs strictly to the switchdev ocelot driver, while
ocelot.c is part of a library shared with the DSA felix driver.
The ocelot_port_bridge_leave function (part of the common library) used
to call ocelot_port_vlan_filtering(false), something which is not
necessary for DSA, since the framework deals with that already there.
So we move this function to ocelot_switchdev_unsync, which is specific
to the switchdev driver.
The code movement described above makes ocelot_port_bridge_leave no
longer return an error code, so we change its type from int to void.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Mon, 22 Mar 2021 23:51:50 +0000 (01:51 +0200)]
net: dsa: sync up switchdev objects and port attributes when joining the bridge
If we join an already-created bridge port, such as a bond master
interface, then we can miss the initial switchdev notifications emitted
by the bridge for this port, while it wasn't offloaded by anybody.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Mon, 22 Mar 2021 23:51:49 +0000 (01:51 +0200)]
net: dsa: inherit the actual bridge port flags at join time
DSA currently assumes that the bridge port starts off with this
constellation of bridge port flags:
- learning on
- unicast flooding on
- multicast flooding on
- broadcast flooding on
just by virtue of code copy-pasta from the bridge layer (new_nbp).
This was a simple enough strategy thus far, because the 'bridge join'
moment always coincided with the 'bridge port creation' moment.
But with sandwiched interfaces, such as:
br0
|
bond0
|
swp0
it may happen that the user has had time to change the bridge port flags
of bond0 before enslaving swp0 to it. In that case, swp0 will falsely
assume that the bridge port flags are those determined by new_nbp, when
in fact this can happen:
ip link add br0 type bridge
ip link add bond0 type bond
ip link set bond0 master br0
ip link set bond0 type bridge_slave learning off
ip link set swp0 master br0
Now swp0 has learning enabled, bond0 has learning disabled. Not nice.
Fix this by "dumpster diving" through the actual bridge port flags with
br_port_flag_is_set, at bridge join time.
We use this opportunity to split dsa_port_change_brport_flags into two
distinct functions called dsa_port_inherit_brport_flags and
dsa_port_clear_brport_flags, now that the implementation for the two
cases is no longer similar. This patch also creates two functions called
dsa_port_switchdev_sync and dsa_port_switchdev_unsync which collect what
we have so far, even if that's asymmetrical. More is going to be added
in the next patch.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Mon, 22 Mar 2021 23:51:48 +0000 (01:51 +0200)]
net: dsa: pass extack to dsa_port_{bridge,lag}_join
This is a pretty noisy change that was broken out of the larger change
for replaying switchdev attributes and objects at bridge join time,
which is when these extack objects are actually used.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Tobias Waldekranz <tobias@waldekranz.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Mon, 22 Mar 2021 23:51:47 +0000 (01:51 +0200)]
net: dsa: call dsa_port_bridge_join when joining a LAG that is already in a bridge
DSA can properly detect and offload this sequence of operations:
ip link add br0 type bridge
ip link add bond0 type bond
ip link set swp0 master bond0
ip link set bond0 master br0
But not this one:
ip link add br0 type bridge
ip link add bond0 type bond
ip link set bond0 master br0
ip link set swp0 master bond0
Actually the second one is more complicated, due to the elapsed time
between the enslavement of bond0 and the offloading of it via swp0, a
lot of things could have happened to the bond0 bridge port in terms of
switchdev objects (host MDBs, VLANs, altered STP state etc). So this is
a bit of a can of worms, and making sure that the DSA port's state is in
sync with this already existing bridge port is handled in the next
patches.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Tobias Waldekranz <tobias@waldekranz.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Mon, 22 Mar 2021 23:51:46 +0000 (01:51 +0200)]
net: bridge: add helper to replay VLANs installed on port
Currently this simple setup with DSA:
ip link add br0 type bridge vlan_filtering 1
ip link add bond0 type bond
ip link set bond0 master br0
ip link set swp0 master bond0
will not work because the bridge has created the PVID in br_add_if ->
nbp_vlan_init, and it has notified switchdev of the existence of VLAN 1,
but that was too early, since swp0 was not yet a lower of bond0, so it
had no reason to act upon that notification.
We need a helper in the bridge to replay the switchdev VLAN objects that
were notified since the bridge port creation, because some of them may
have been missed.
As opposed to the br_mdb_replay function, the vg->vlan_list write side
protection is offered by the rtnl_mutex which is sleepable, so we don't
need to queue up the objects in atomic context, we can replay them right
away.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Mon, 22 Mar 2021 23:51:45 +0000 (01:51 +0200)]
net: bridge: add helper to replay port and local fdb entries
When a switchdev port starts offloading a LAG that is already in a
bridge and has an FDB entry pointing to it:
ip link set bond0 master br0
bridge fdb add dev bond0 00:01:02:03:04:05 master static
ip link set swp0 master bond0
the switchdev driver will have no idea that this FDB entry is there,
because it missed the switchdev event emitted at its creation.
Ido Schimmel pointed this out during a discussion about challenges with
switchdev offloading of stacked interfaces between the physical port and
the bridge, and recommended to just catch that condition and deny the
CHANGEUPPER event:
https://lore.kernel.org/netdev/20210210105949.GB287766@shredder.lan/
But in fact, we might need to deal with the hard thing anyway, which is
to replay all FDB addresses relevant to this port, because it isn't just
static FDB entries, but also local addresses (ones that are not
forwarded but terminated by the bridge). There, we can't just say 'oh
yeah, there was an upper already so I'm not joining that'.
So, similar to the logic for replaying MDB entries, add a function that
must be called by individual switchdev drivers and replays local FDB
entries as well as ones pointing towards a bridge port. This time, we
use the atomic switchdev notifier block, since that's what FDB entries
expect for some reason.
Reported-by: Ido Schimmel <idosch@idosch.org> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Mon, 22 Mar 2021 23:51:44 +0000 (01:51 +0200)]
net: bridge: add helper to replay port and host-joined mdb entries
I have a system with DSA ports, and udhcpcd is configured to bring
interfaces up as soon as they are created.
I create a bridge as follows:
ip link add br0 type bridge
As soon as I create the bridge and udhcpcd brings it up, I also have
avahi which automatically starts sending IPv6 packets to advertise some
local services, and because of that, the br0 bridge joins the following
IPv6 groups due to the code path detailed below:
33:33:ff:6d:c1:9c vid 0
33:33:00:00:00:6a vid 0
33:33:00:00:00:fb vid 0
This is all fine, but inside br_mdb_notify we have br_mdb_switchdev_host
hooked up, and switchdev will attempt to offload the host joined groups
to an empty list of ports. Of course nobody offloads them.
Then when we add a port to br0:
ip link set swp0 master br0
the bridge doesn't replay the host-joined MDB entries from br_add_if,
and eventually the host joined addresses expire, and a switchdev
notification for deleting it is emitted, but surprise, the original
addition was already completely missed.
The strategy to address this problem is to replay the MDB entries (both
the port ones and the host joined ones) when the new port joins the
bridge, similar to what vxlan_fdb_replay does (in that case, its FDB can
be populated and only then attached to a bridge that you offload).
However there are 2 possibilities: the addresses can be 'pushed' by the
bridge into the port, or the port can 'pull' them from the bridge.
Considering that in the general case, the new port can be really late to
the party, and there may have been many other switchdev ports that
already received the initial notification, we would like to avoid
delivering duplicate events to them, since they might misbehave. And
currently, the bridge calls the entire switchdev notifier chain, whereas
for replaying it should just call the notifier block of the new guy.
But the bridge doesn't know what is the new guy's notifier block, it
just knows where the switchdev notifier chain is. So for simplification,
we make this a driver-initiated pull for now, and the notifier block is
passed as an argument.
To emulate the calling context for mdb objects (deferred and put on the
blocking notifier chain), we must iterate under RCU protection through
the bridge's mdb entries, queue them, and only call them once we're out
of the RCU read-side critical section.
There was some opportunity for reuse between br_mdb_switchdev_host_port,
br_mdb_notify and the newly added br_mdb_queue_one in how the switchdev
mdb object is created, so a helper was created.
Suggested-by: Ido Schimmel <idosch@idosch.org> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
therefore not at bridge port creation time, so:
(a) switchdev drivers have to hardcode the initial value for the address
ageing time, because they didn't get any notification
(b) that hardcoded value can be out of sync, if the user changes the
ageing time before enslaving the port to the bridge
We need a helper in the bridge, such that switchdev drivers can query
the current value of the bridge ageing time when they start offloading
it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Tobias Waldekranz <tobias@waldekranz.com> Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Mon, 22 Mar 2021 23:51:42 +0000 (01:51 +0200)]
net: bridge: add helper for retrieving the current bridge port STP state
It may happen that we have the following topology with DSA or any other
switchdev driver with LAG offload:
ip link add br0 type bridge stp_state 1
ip link add bond0 type bond
ip link set bond0 master br0
ip link set swp0 master bond0
ip link set swp1 master bond0
STP decides that it should put bond0 into the BLOCKING state, and
that's that. The ports that are actively listening for the switchdev
port attributes emitted for the bond0 bridge port (because they are
offloading it) and have the honor of seeing that switchdev port
attribute can react to it, so we can program swp0 and swp1 into the
BLOCKING state.
But if then we do:
ip link set swp2 master bond0
then as far as the bridge is concerned, nothing has changed: it still
has one bridge port. But this new bridge port will not see any STP state
change notification and will remain FORWARDING, which is how the
standalone code leaves it in.
We need a function in the bridge driver which retrieves the current STP
state, such that drivers can synchronize to it when they may have missed
switchdev events.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Tobias Waldekranz <tobias@waldekranz.com> Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Xie He [Sun, 21 Mar 2021 09:39:35 +0000 (02:39 -0700)]
net: lapb: Make "lapb_t1timer_running" able to detect an already running timer
Problem:
The "lapb_t1timer_running" function in "lapb_timer.c" is used in only
one place: in the "lapb_kick" function in "lapb_out.c". "lapb_kick" calls
"lapb_t1timer_running" to check if the timer is already pending, and if
it is not, schedule it to run.
However, if the timer has already fired and is running, and is waiting to
get the "lapb->lock" lock, "lapb_t1timer_running" will not detect this,
and "lapb_kick" will then schedule a new timer. The old timer will then
abort when it sees a new timer pending.
I think this is not right. The purpose of "lapb_kick" should be ensuring
that the actual work of the timer function is scheduled to be done.
If the timer function is already running but waiting for the lock,
"lapb_kick" should not abort and reschedule it.
Changes made:
I added a new field "t1timer_running" in "struct lapb_cb" for
"lapb_t1timer_running" to use. "t1timer_running" will accurately reflect
whether the actual work of the timer is pending. If the timer has fired
but is still waiting for the lock, "t1timer_running" will still correctly
reflect whether the actual work is waiting to be done.
The old "t1timer_stop" field, whose only responsibility is to ask a timer
(that is already running but waiting for the lock) to abort, is no longer
needed, because the new "t1timer_running" field can fully take over its
responsibility. Therefore "t1timer_stop" is deleted.
"t1timer_running" is not simply a negation of the old "t1timer_stop".
At the end of the timer function, if it does not reschedule itself,
"t1timer_running" is set to false to indicate that the timer is stopped.
For consistency of the code, I also added "t2timer_running" and deleted
"t2timer_stop".
Signed-off-by: Xie He <xie.he.0141@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enable -Wimplicit-fallthrough for Clang, fix a warning
by explicitly adding a break statement instead of just letting the code
fall through to the next case.
Link: https://github.com/KSPP/linux/issues/115 Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In preparation to enable -Wimplicit-fallthrough for Clang, fix a warning
by explicitly adding a break statement instead of just letting the code
fall through to the next case.
Link: https://github.com/KSPP/linux/issues/115 Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In preparation to enable -Wimplicit-fallthrough for Clang, fix multiple
warnings by explicitly adding multiple break statements instead of just
letting the code fall through to the next case.
Link: https://github.com/KSPP/linux/issues/115 Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In preparation to enable -Wimplicit-fallthrough for Clang, fix multiple
warnings by explicitly adding multiple break statements instead of just
letting the code fall through to the next case.
Link: https://github.com/KSPP/linux/issues/115 Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In preparation to enable -Wimplicit-fallthrough for Clang, fix multiple
warnings by explicitly adding a couple of break statements instead of
just letting the code fall through to the next case.
Link: https://github.com/KSPP/linux/issues/115 Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In preparation to enable -Wimplicit-fallthrough for Clang, fix a warning
by explicitly adding a break statement instead of just letting the code
fall through to the next case.
Link: https://github.com/KSPP/linux/issues/115 Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org> Tested-by: Tony Brelinski <tonyx.brelinski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Kurt Kanzenbach [Mon, 22 Mar 2021 18:51:13 +0000 (19:51 +0100)]
net: dsa: hellcreek: Report switch name and ID
Report the driver name, ASIC ID and the switch name via devlink. This is a
useful information for user space tooling.
Signed-off-by: Kurt Kanzenbach <kurt@kmk-computers.de> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 22 Mar 2021 23:37:45 +0000 (16:37 -0700)]
Merge branch 'dpaa2-switch-offload-port-flags'
Ioana Ciornei says:
====================
dpaa2-switch: offload bridge port flags to device
Add support for offloading bridge port flags to the switch. With this
patch set, the learning, broadcast flooding and unknown ucast/mcast
flooding states will be user configurable.
Apart from that, the last patch is a small fix that configures the
offload_fwd_mark if the switch port is under a bridge or not.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ioana Ciornei [Mon, 22 Mar 2021 20:58:59 +0000 (22:58 +0200)]
dpaa2-switch: mark skbs with offload_fwd_mark
If a switch port is under a bridge, the offload_fwd_mark should be setup
before sending the skb towards the stack so that the bridge does not try
to flood the packet on the other switch ports.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ioana Ciornei [Mon, 22 Mar 2021 20:58:58 +0000 (22:58 +0200)]
dpaa2-switch: add support for configuring per port unknown flooding
Add support for configuring per port unknown flooding by accepting both
BR_FLOOD and BR_MCAST_FLOOD as offloadable bridge port flags.
The DPAA2 switch does not support at the moment configuration of unknown
multicast flooding independently of unknown unicast flooding, therefore
check that both BR_FLOOD and BR_MCAST_FLOOD have the same state.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ioana Ciornei [Mon, 22 Mar 2021 20:58:57 +0000 (22:58 +0200)]
dpaa2-switch: add support for configuring per port broadcast flooding
The BR_BCAST_FLOOD bridge port flag is now accepted by the driver and a
change in its state will determine a reconfiguration of the broadcast
egress flooding list on the FDB associated with the port.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ioana Ciornei [Mon, 22 Mar 2021 20:58:56 +0000 (22:58 +0200)]
dpaa2-switch: add support for configuring learning state per port
Add support for configuring the learning state of a switch port.
When the user requests the HW learning to be disabled, a fast-age
procedure on that specific port is run so that previously learnt
addresses do not linger.
At device probe as well as on a bridge leave action, the ports are
configured with HW learning disabled since they are basically a
standalone port.
At the same time, at bridge join we inherit the bridge port BR_LEARNING
flag state and configure it on the switch port.
There were already some MC firmware ABI functions for changing the
learning state, but those were per FDB (bridging domain) and not per
port so we need to adjust those to use the new MC fw command which is
per port.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 22 Mar 2021 23:33:39 +0000 (16:33 -0700)]
Merge branch 'lantiq-xrx300-xrx330'
Aleksander Jan Bajkowski says:
====================
net: dsa: lantiq: add support for xRX300 and xRX330
Changed since v3:
* fixed last compilation warning
Changed since v2:
* fixed compilation warnings
* removed example bindings for xrx330
* patches has been refactored due to upstream changes
Changed since v1:
* gswip_mii_mask_cfg() can now change port 3 on xRX330
* changed alowed modes on port 0 and 5 for xRX300 and xRX330
* moved common part of phylink validation into gswip_phylink_set_capab()
* verify the compatible string against the hardware
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
net: dsa: lantiq: allow to use all GPHYs on xRX300 and xRX330
This patch allows to use all PHYs on GRX300 and GRX330. The ARX300
has 3 and the GRX330 has 4 integrated PHYs connected to different
ports compared to VRX200. Each integrated PHY can work as single
Gigabit Ethernet PHY (GMII) or as double Fast Ethernet PHY (MII).
Allowed port configurations:
xRX200:
GMAC0: RGMII, MII, REVMII or RMII port
GMAC1: RGMII, MII, REVMII or RMII port
GMAC2: GPHY0 (GMII)
GMAC3: GPHY0 (MII)
GMAC4: GPHY1 (GMII)
GMAC5: GPHY1 (MII) or RGMII port
xRX300:
GMAC0: RGMII port
GMAC1: GPHY2 (GMII)
GMAC2: GPHY0 (GMII)
GMAC3: GPHY0 (MII)
GMAC4: GPHY1 (GMII)
GMAC5: GPHY1 (MII) or RGMII port
xRX330:
GMAC0: RGMII, GMII or RMII port
GMAC1: GPHY2 (GMII)
GMAC2: GPHY0 (GMII)
GMAC3: GPHY0 (MII) or GPHY3 (GMII)
GMAC4: GPHY1 (GMII)
GMAC5: GPHY1 (MII), RGMII or RMII port
Tested on D-Link DWR966 (xRX330) with OpenWRT.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl> Acked-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 22 Mar 2021 23:29:40 +0000 (16:29 -0700)]
Merge branch '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
100GbE Intel Wired LAN Driver Updates 2021-03-22
This series contains updates to ice and iavf drivers.
Haiyue Wang says:
The Intel E810 Series supports a programmable pipeline for a domain
specific protocols classification, for example GTP by Dynamic Device
Personalization (DDP) profile.
The E810 PF has introduced flex-bytes support by ethtool user-def option
allowing for packet deeper matching based on an offset and value for DDP
usage.
For making VF also benefit from this flexible protocol classification,
some new virtchnl messages are defined and handled by PF, so VF can
query this new flow director capability, and use ethtool with extending
the user-def option to configure Rx flow classification.
The new user-def 0xAAAABBBBCCCCDDDD: BBBB is the 2 byte pattern while
AAAA corresponds to its offset in the packet. Similarly DDDD is the 2
byte pattern with CCCC being the corresponding offset. The offset ranges
from 0x0 to 0x1F7 (up to 504 bytes into the packet). The offset starts
from the beginning of the packet.
This feature can be used to allow customers to set flow director rules
for protocols headers that are beyond standard ones supported by
ethtool (e.g. PFCP or GTP-U).
Like for matching GTP-U's TEID value 0x10203040:
ethtool -N ens787f0v0 flow-type udp4 dst-port 2152 \
user-def 0x002e102000303040 action 13
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 22 Mar 2021 20:45:46 +0000 (13:45 -0700)]
Merge branch 'mlxsw-resil-nexthop-groups-prep'
Ido Schimmel says:
====================
mlxsw: Preparations for resilient nexthop groups
This patchset contains preparations for resilient nexthop groups support in
mlxsw. A follow-up patchset will add support and selftests. Most of the
patches are trivial and small to make review easier.
Patchset overview:
Patch #1 removes RTNL assertion in nexthop notifier block since it is
not needed. The assertion will trigger when mlxsw starts processing
notifications related to resilient groups as not all are emitted with
RTNL held.
Patches #2-#9 gradually add support for nexthops with trap action. Up
until now mlxsw did not program nexthops whose neighbour entry was not
resolved. This will not work with resilient groups as their size is
fixed and the nexthop mapped to each bucket is determined by the nexthop
code. Therefore, nexthops whose neighbour entry is not resolved will be
programmed to trap packets to the CPU in order to trigger neighbour
resolution.
Patch #10 is a non-functional change to allow for code reuse between
regular nexthop groups and resilient ones.
Patch #11 avoids unnecessary neighbour updates in hardware. See the
commit message for a detailed explanation.
Patches #12-#14 add support for additional nexthop group sizes that are
supported by Spectrum-{2,3} ASICs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Mon, 22 Mar 2021 15:58:55 +0000 (17:58 +0200)]
mlxsw: spectrum_router: Add Spectrum-{2, 3} adjacency group size ranges
Spectrum-{2,3} support different adjacency group size ranges compared to
Spectrum-1. Add an array describing these ranges and change the common
code to use the array which was set during the per-ASIC initialization.
Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Petr Machata <petrm@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Mon, 22 Mar 2021 15:58:54 +0000 (17:58 +0200)]
mlxsw: spectrum_router: Encode adjacency group size ranges in an array
The device supports a fixed set of adjacency group sizes. Encode these
sizes in an array, so that the next patch will be able to split it
between Spectrum-1 and Spectrum-{2,3}, which support different size
ranges.
Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Petr Machata <petrm@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
There are several differences in the router module between Spectrum-1
and Spectrum-{2,3}. Currently, this is only apparent in the router
interface (RIF) operations that are split between these ASICs.
A subsequent patch is going to introduce another difference between
these ASICs.
Create per-ASIC router operations that will encapsulate all these
differences. For now, these operations are only used to set the per-ASIC
RIF operations in 'mlxsw_sp->router->rif_ops_arr'. Note that this fields
was unused since commit 1f5b23033937 ("mlxsw: spectrum: Set RIF ops per
ASIC type").
Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Petr Machata <petrm@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid updating neighbour and adjacency entries in hardware when the
neighbour is already connected and its MAC address did not change. This
can happen, for example, when neighbour transitions between valid states
such as 'NUD_REACHABLE' and 'NUD_DELAY'.
This is especially important for resilient hashing as these updates will
result in adjacency entries being marked as active.
Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Petr Machata <petrm@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Mon, 22 Mar 2021 15:58:51 +0000 (17:58 +0200)]
mlxsw: spectrum_router: Break nexthop group entry validation to a separate function
The validation of a nexthop group entry is also necessary for resilient
nexthop groups, so break the validation to a separate function to allow
for code reuse in subsequent patches.
Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Petr Machata <petrm@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Mon, 22 Mar 2021 15:58:50 +0000 (17:58 +0200)]
mlxsw: spectrum_router: Encapsulate nexthop update in a function
Encapsulate this functionality in a separate function, so that it could
be invoked by follow-up patches, when replacing a nexthop bucket that is
part of a resilient nexthop group.
Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Petr Machata <petrm@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Mon, 22 Mar 2021 15:58:49 +0000 (17:58 +0200)]
mlxsw: spectrum_router: Rename nexthop update function to reflect its type
mlxsw_sp_nexthop_update() is used to update the configuration of
Ethernet-type nexthops, as opposed to mlxsw_sp_nexthop_ipip_update(),
which is used to update IPinIP-type nexthops.
Rename the function to mlxsw_sp_nexthop_eth_update(), so that it is
consistent with mlxsw_sp_nexthop_ipip_update().
It will allow us to introduce mlxsw_sp_nexthop_update() in a follow-up
patch, which calls either of above mentioned function based on the
nexthop's type.
Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Petr Machata <petrm@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Mon, 22 Mar 2021 15:58:48 +0000 (17:58 +0200)]
mlxsw: spectrum_router: Add nexthop trap action support
Currently, nexthops are programmed with either forward or discard action
(for blackhole nexthops). Nexthops that do not have a valid MAC address
(neighbour) or router interface (RIF) are simply not written to the
adjacency table.
In resilient nexthop groups, the size of the group must remain fixed and
the kernel is in complete control of the layout of the adjacency table.
A nexthop without a valid MAC or RIF will therefore be written with a
trap action, to trigger neighbour resolution.
Allow such nexthops to be programmed to the adjacency table to enable
above mentioned use case.
Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Petr Machata <petrm@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Mon, 22 Mar 2021 15:58:47 +0000 (17:58 +0200)]
mlxsw: spectrum_router: Prepare for nexthops with trap action
Nexthops that need to be programmed with a trap action might not have a
valid router interface (RIF) associated with them. Therefore, use the
loopback RIF created during initialization to program them to the
device.
Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Petr Machata <petrm@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Mon, 22 Mar 2021 15:58:46 +0000 (17:58 +0200)]
mlxsw: spectrum_router: Introduce nexthop action field
Currently, the action associated with the nexthop is assumed to be
'forward' unless the 'discard' bit is set.
Instead, simplify this by introducing a dedicated field to represent the
action of the nexthop. This will allow us to more easily introduce more
actions, such as trap.
Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Petr Machata <petrm@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Mon, 22 Mar 2021 15:58:45 +0000 (17:58 +0200)]
mlxsw: spectrum_router: Adjust comments on nexthop fields
The comments assume that nexthops are simple Ethernet nexthops
that are programmed to forward packets to the associated neighbour. This
is no longer the case, as both IPinIP and blackhole nexthops are now
supported.
Adjust the comments to reflect these changes.
Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Petr Machata <petrm@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Mon, 22 Mar 2021 15:58:44 +0000 (17:58 +0200)]
mlxsw: spectrum_router: Only provide MAC address for valid nexthops
The helper returns the MAC address associated with the nexthop. It is
only valid when the nexthop forwards packets and when it is an Ethernet
nexthop. Reflect this in the checks the helper is performing.
This is not an issue because the sole caller of the function only
invokes it for such nexthops.
Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Petr Machata <petrm@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The helper mlxsw_sp_nexthop_offload() is actually interested in finding
out if the nexthop is both written to the adjacency table and forwarding
packets (as opposed to discarding them).
Rename it to mlxsw_sp_nexthop_is_forward() and remove
mlxsw_sp_nexthop_is_discard().
Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Petr Machata <petrm@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: bridge: when suppression is enabled exclude RARP packets
Recently we had an interop issue where RARP packets got suppressed with
bridge neigh suppression enabled, but the check in the code was meant to
suppress GARP. Exclude RARP packets from it which would allow some VMWare
setups to work, to quote the report:
"Those RARP packets usually get generated by vMware to notify physical
switches when vMotion occurs. vMware may use random sip/tip or just use
sip=tip=0. So the RARP packet sometimes get properly flooded by the vtep
and other times get dropped by the logic"
Reported-by: Amer Abdalamer <amer@nvidia.com> Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Antoine Tenart [Mon, 22 Mar 2021 15:43:29 +0000 (16:43 +0100)]
net-sysfs: remove possible sleep from an RCU read-side critical section
xps_queue_show is mostly made of an RCU read-side critical section and
calls bitmap_zalloc with GFP_KERNEL in the middle of it. That is not
allowed as this call may sleep and such behaviours aren't allowed in RCU
read-side critical sections. Fix this by using GFP_NOWAIT instead.
Fixes: 5478fcd0f483 ("net: embed nr_ids in the xps maps") Reported-by: kernel test robot <oliver.sang@intel.com> Suggested-by: Matthew Wilcox <willy@infradead.org> Signed-off-by: Antoine Tenart <atenart@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Yongjun [Mon, 22 Mar 2021 12:23:59 +0000 (12:23 +0000)]
net: stmmac: platform: fix build error with !CONFIG_PM_SLEEP
Get rid of the CONFIG_PM_SLEEP ifdefery to fix the build error
and use __maybe_unused for the suspend()/resume() hooks to avoid
build warning:
drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c:769:21:
error: 'stmmac_runtime_suspend' undeclared here (not in a function); did you mean 'stmmac_suspend'?
769 | SET_RUNTIME_PM_OPS(stmmac_runtime_suspend, stmmac_runtime_resume, NULL)
| ^~~~~~~~~~~~~~~~~~~~~~
./include/linux/pm.h:342:21: note: in definition of macro 'SET_RUNTIME_PM_OPS'
342 | .runtime_suspend = suspend_fn, \
| ^~~~~~~~~~
drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c:769:45:
error: 'stmmac_runtime_resume' undeclared here (not in a function)
769 | SET_RUNTIME_PM_OPS(stmmac_runtime_suspend, stmmac_runtime_resume, NULL)
| ^~~~~~~~~~~~~~~~~~~~~
./include/linux/pm.h:343:20: note: in definition of macro 'SET_RUNTIME_PM_OPS'
343 | .runtime_resume = resume_fn, \
| ^~~~~~~~~
Fixes: 5ec55823438e ("net: stmmac: add clocks management for gmac driver") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Bhaskar Chowdhury <unixbhaskar@gmail.com> Acked-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Mon, 22 Mar 2021 12:14:47 +0000 (13:14 +0100)]
misdn: avoid -Wempty-body warning
gcc warns about a pointless condition:
drivers/isdn/hardware/mISDN/hfcmulti.c: In function 'hfcmulti_interrupt':
drivers/isdn/hardware/mISDN/hfcmulti.c:2752:17: error: suggest braces around empty body in an 'if' statement [-Werror=empty-body]
2752 | ; /* external IRQ */
As the check has no effect, just remove it.
Suggested-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Mon, 22 Mar 2021 11:31:48 +0000 (13:31 +0200)]
net: move the ptype_all and ptype_base declarations to include/linux/netdevice.h
ptype_all and ptype_base are declared in net/core/dev.c as non-static,
because they are used by net-procfs.c too. However, a "make W=1" build
complains that there was no previous declaration of ptype_all and
ptype_base in a header file, so this way of declaring things constitutes
a violation of coding style.
Let's move the extern declarations of ptype_all and ptype_base to the
linux/netdevice.h file, which is included by net-procfs.c too.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Mon, 22 Mar 2021 11:30:19 +0000 (13:30 +0200)]
net: make xps_needed and xps_rxqs_needed static
Since their introduction in commit 04157469b7b8 ("net: Use static_key
for XPS maps"), xps_needed and xps_rxqs_needed were never used outside
net/core/dev.c, so I don't really understand why they were exported as
symbols in the first place.
This is needed in order to silence a "make W=1" warning about these
static keys not being declared as static variables, but not having a
previous declaration in a header file nonetheless.
Cc: Amritha Nambiar <amritha.nambiar@intel.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Mon, 22 Mar 2021 10:38:19 +0000 (12:38 +0200)]
net: bridge: declare br_vlan_tunnel_lookup argument tunnel_id as __be64
The only caller of br_vlan_tunnel_lookup, br_handle_ingress_vlan_tunnel,
extracts the tunnel_id from struct ip_tunnel_info::struct ip_tunnel_key::
tun_id which is a __be64 value.
The exact endianness does not seem to matter, because the tunnel id is
just used as a lookup key for the VLAN group's tunnel hash table, and
the value is not interpreted directly per se. Moreover,
rhashtable_lookup_fast treats the key argument as a const void *.
Therefore, there is no functional change associated with this patch,
just one to silence "make W=1" builds.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiapeng Chong [Mon, 22 Mar 2021 09:53:14 +0000 (17:53 +0800)]
cxgb4: Remove redundant NULL check
Fix the following coccicheck warnings:
./drivers/net/ethernet/chelsio/cxgb4/cudbg_lib.c:3540:2-8: WARNING: NULL
check before some freeing functions is not needed.
Reported-by: Abaci Robot <abaci@linux.alibaba.com> Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Mon, 22 Mar 2021 09:30:09 +0000 (11:30 +0200)]
net: dsa: mv88e6xxx: fix up kerneldoc some more
Commit 0b5294483c35 ("net: dsa: mv88e6xxx: scratch: Fixup kerneldoc")
has addressed some but not all kerneldoc warnings for the Global 2
Scratch register accessors. Namely, we have some mismatches between
the function names in the kerneldoc and the ones in the actual code.
Let's adjust the comments so that they match the functions they're
sitting next to.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Mon, 22 Mar 2021 07:08:45 +0000 (03:08 -0400)]
bnxt_en: Enhance retry of the first message to the firmware.
Two enhancements:
1. Read the health status first before sending the first
HWRM_VER_GET message to firmware instead of the other way around.
This guarantees we got the accurate health status before we attempt
to send the message.
2. We currently only retry sending the first HWRM_VER_GET message to
the firmware if the firmware is in the process of booting. If the
firmware is in error state and is doing core dump for example, the
driver should also retry if the health register has the RECOVERING
flag set. This flag indicates the firmware will undergo recovery
soon. Modify the retry logic to retry for this case as well.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vasundhara Volam [Mon, 22 Mar 2021 07:08:44 +0000 (03:08 -0400)]
bnxt_en: Remove the read of BNXT_FW_RESET_INPROG_REG after firmware reset.
Once the chip goes through reset, the register mapping may be lost
and any read of the mapped health registers may return garbage value
until the registers are mapped again in the init path.
Reading BNXT_FW_RESET_INPROG_REG after firmware reset will likely
return garbage value due to the above reason. Reading this register
is for information purpose only so remove it.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com> Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Mon, 22 Mar 2021 07:08:43 +0000 (03:08 -0400)]
bnxt_en: Set BNXT_STATE_FW_RESET_DET flag earlier for the RDMA driver.
During ifup, if the driver detects that firmware has gone through a
reset, it will go through a re-probe sequence. If the RDMA driver is
loaded, the re-probe sequence includes calling the RDMA driver to stop.
We need to set the BNXT_STATE_FW_RESET_DET flag earlier so that it is
visible to the RDMA driver. The RDMA driver's stop sequence is
different if firmware has gone through a reset.
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Reviewed-by: P B S Naresh Kumar <nareshkumar.pbs@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Scott Branden [Mon, 22 Mar 2021 07:08:42 +0000 (03:08 -0400)]
bnxt_en: check return value of bnxt_hwrm_func_resc_qcaps
Check return value of call to bnxt_hwrm_func_resc_qcaps in
bnxt_hwrm_if_change and return failure on error.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com> Signed-off-by: Scott Branden <scott.branden@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Edwin Peer [Mon, 22 Mar 2021 07:08:41 +0000 (03:08 -0400)]
bnxt_en: don't fake firmware response success when PCI is disabled
The original intent here is to allow commands during reset to succeed
without error when the device is disabled, to ensure that cleanup
completes normally during NIC close, where firmware is not necessarily
expected to respond.
The problem with faking success during reset's PCI disablement is that
unrelated ULP commands will also see inadvertent success during reset
when failure would otherwise be appropriate. It is better to return
a different error result such that reset related code can detect
this unique condition and ignore as appropriate.
Note, the pci_disable_device() when firmware is fatally wounded in
bnxt_fw_reset_close() does not need to be addressed, as subsequent
commands are already expected to fail due to the BNXT_NO_FW_ACCESS()
check in bnxt_hwrm_do_send_msg().
Reviewed-by: Scott Branden <scott.branden@broadcom.com> Signed-off-by: Edwin Peer <edwin.peer@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Pavan Chebbi [Mon, 22 Mar 2021 07:08:40 +0000 (03:08 -0400)]
bnxt_en: Improve wait for firmware commands completion
In situations where FW has crashed, the bnxt_hwrm_do_send_msg() call
will have to wait until timeout for each firmware message. This
generally takes about half a second for each firmware message. If we
try to unload the driver n this state, the unload sequence will take
a long time to complete.
Improve this by checking the health register if it is available and
abort the wait for the firmware response if the register shows that
firmware is not healthy. The very first message HWRM_VER_GET is
excluded from this check because that message is used to poll for
firmware to come out of reset during error recovery.
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Mon, 22 Mar 2021 07:08:39 +0000 (03:08 -0400)]
bnxt_en: Improve the status_reliable flag in bp->fw_health.
In order to read the firmware health status, we first need to determine
the register location and then the register may need to be mapped.
There are 2 code paths to do this. The first one is done early as a
best effort attempt by the function bnxt_try_map_fw_health_reg(). The
second one is done later in the function bnxt_map_fw_health_regs()
after establishing communications with the firmware. We currently
only set fw_health->status_reliable if we can successfully set up the
health register in the first code path.
Improve the scheme by setting the fw_health->status_reliable flag if
either (or both) code paths can successfully set up the health
register. This flag is relied upon during run-time when we need to
check the health status. So this will make it work better.
During ifdown, if the health register is mapped, we need to invalidate
the health register mapping because a potential fw reset will reset
the mapping. Similarly, we need to do the same after firmware reset
during recovery. We'll remap it during ifup.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com> Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 22 Mar 2021 20:04:18 +0000 (13:04 -0700)]
Merge branch 'hns3-flow-director'
Huazhong Tan says:
====================
net: hns3: refactor and new features for flow director
This patchset refactor some functions and add some new features for
flow director.
patch 1~3: refactor large functions
patch 4, 7: add traffic class and user-def field support for ethtool
patch 5: refactor flow director configuration
patch 6: clean up for hns3_del_all_fd_entries()
change log:
V1->V2: modifies patch 5 as Jakub suggested, keep configuring
ethtool/tc flower rules synchronously while aRFS
asynchronously.
changes the usecnt of user-def rule checking in patch 7.
removes previous patches 8 and 9 from this series, since
there are issues that need further discussion.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jian Shen [Mon, 22 Mar 2021 03:52:02 +0000 (11:52 +0800)]
net: hns3: add support for user-def data of flow director
For DEVICE_VERSION_V3, the hardware supports to match specified
data in the specified offset of packet payload. Each layer can
have one offset, and can't be masked when configure flow director
rule by ethtool command. The layer is selected based on the
flow-type, ether for L2, ip4/ipv6 for L3, and tcp4/tcp6/udp4/udp6
for L4. For example, tcp4/tcp6/udp4/udp6 rules share the same
user-def offset, but each rule can have its own user-def value.
For the user-def field of ethtool -N/U command is 64 bits long.
The bit 0~15 is used for user-def value, and bit 32~47 for user-def
offset in HNS3 driver.
Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jian Shen [Mon, 22 Mar 2021 03:52:01 +0000 (11:52 +0800)]
net: hns3: refine for hns3_del_all_fd_entries()
For only PF driver can configure flow director rule, it's
better to call hclge_del_all_fd_entries() directly in hclge
layer, rather than call hns3_del_all_fd_entries() in hns3
layer. Then the ae_algo->ops.del_all_fd_entries can be removed.
Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / mirror_ubuntu-jammy-kernel.git / log