Ivan Vecera [Tue, 8 Nov 2022 09:35:34 +0000 (10:35 +0100)]
iavf: Fix a crash during reset task
Recent commit aa626da947e9 ("iavf: Detach device during reset task")
removed netif_tx_stop_all_queues() with an assumption that Tx queues
are already stopped by netif_device_detach() in the beginning of
reset task. This assumption is incorrect because during reset
task a potential link event can start Tx queues again.
Revert this change to fix this issue.
Reproducer:
1. Run some Tx traffic (e.g. iperf3) over iavf interface
2. Switch MTU of this interface in a loop
Wang Hai [Thu, 17 Nov 2022 06:55:27 +0000 (14:55 +0800)]
net: pch_gbe: fix potential memleak in pch_gbe_tx_queue()
In pch_gbe_xmit_frame(), NETDEV_TX_OK will be returned whether
pch_gbe_tx_queue() sends data successfully or not, so pch_gbe_tx_queue()
needs to free skb before returning. But pch_gbe_tx_queue() returns without
freeing skb in case of dma_map_single() fails. Add dev_kfree_skb_any()
to fix it.
Fixes: 77555ee72282 ("net: Add Gigabit Ethernet driver of Topcliff PCH") Signed-off-by: Wang Hai <wanghai38@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Lin Ma [Wed, 16 Nov 2022 13:02:49 +0000 (21:02 +0800)]
nfc/nci: fix race with opening and closing
Previously we leverage NCI_UNREG and the lock inside nci_close_device to
prevent the race condition between opening a device and closing a
device. However, it still has problem because a failed opening command
will erase the NCI_UNREG flag and allow another opening command to
bypass the status checking.
This fix corrects that by making sure the NCI_UNREG is held.
Reported-by: syzbot+43475bf3cfbd6e41f5b7@syzkaller.appspotmail.com Fixes: 48b71a9e66c2 ("NFC: add NCI_UNREG flag to eliminate the race") Signed-off-by: Lin Ma <linma@zju.edu.cn> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Wed, 16 Nov 2022 10:06:53 +0000 (12:06 +0200)]
net: dsa: sja1105: disallow C45 transactions on the BASE-TX MDIO bus
You'd think people know that the internal 100BASE-TX PHY on the SJA1110
responds only to clause 22 MDIO transactions, but they don't :)
When a clause 45 transaction is attempted, sja1105_base_tx_mdio_read()
and sja1105_base_tx_mdio_write() don't expect "reg" to contain bit 30
set (MII_ADDR_C45) and pack this value into the SPI transaction buffer.
But the field in the SPI buffer has a width smaller than 30 bits, so we
see this confusing message from the packing() API rather than a proper
rejection of C45 transactions:
Fixes: 5a8f09748ee7 ("net: dsa: sja1105: register the MDIO buses for 100base-T1 and 100base-TX") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
David Howells [Wed, 16 Nov 2022 14:02:28 +0000 (14:02 +0000)]
rxrpc: Fix race between conn bundle lookup and bundle removal [ZDI-CAN-15975]
After rxrpc_unbundle_conn() has removed a connection from a bundle, it
checks to see if there are any conns with available channels and, if not,
removes and attempts to destroy the bundle.
Whilst it does check after grabbing client_bundles_lock that there are no
connections attached, this races with rxrpc_look_up_bundle() retrieving the
bundle, but not attaching a connection for the connection to be attached
later.
There is therefore a window in which the bundle can get destroyed before we
manage to attach a new connection to it.
Fix this by adding an "active" counter to struct rxrpc_bundle:
(1) rxrpc_connect_call() obtains an active count by prepping/looking up a
bundle and ditches it before returning.
(2) If, during rxrpc_connect_call(), a connection is added to the bundle,
this obtains an active count, which is held until the connection is
discarded.
(3) rxrpc_deactivate_bundle() is created to drop an active count on a
bundle and destroy it when the active count reaches 0. The active
count is checked inside client_bundles_lock() to prevent a race with
rxrpc_look_up_bundle().
(4) rxrpc_unbundle_conn() then calls rxrpc_deactivate_bundle().
Fixes: 245500d853e9 ("rxrpc: Rewrite the client connection manager") Reported-by: zdi-disclosures@trendmicro.com # ZDI-CAN-15975 Signed-off-by: David Howells <dhowells@redhat.com> Tested-by: zdi-disclosures@trendmicro.com
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org Signed-off-by: David S. Miller <davem@davemloft.net>
Wang Yufen [Thu, 17 Nov 2022 02:45:03 +0000 (10:45 +0800)]
selftests/net: fix missing xdp_dummy
After commit afef88e65554 ("selftests/bpf: Store BPF object files with
.bpf.o extension"), we should use xdp_dummy.bpf.o instade of xdp_dummy.o.
In addition, use the BPF_FILE variable to save the BPF object file name,
which can be better identified and modified.
Fixes: afef88e65554 ("selftests/bpf: Store BPF object files with .bpf.o extension") Signed-off-by: Wang Yufen <wangyufen@huawei.com> Cc: Daniel Müller <deso@posteo.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Mahesh Bandewar [Wed, 16 Nov 2022 01:19:14 +0000 (17:19 -0800)]
ipvlan: hold lower dev to avoid possible use-after-free
Recently syzkaller discovered the issue of disappearing lower
device (NETDEV_UNREGISTER) while the virtual device (like
macvlan) is still having it as a lower device. So it's just
a matter of time similar discovery will be made for IPvlan
device setup. So fixing it preemptively. Also while at it,
add a refcount tracker.
Fixes: 2ad7bf363841 ("ipvlan: Initial check-in of the IPVLAN driver.") Signed-off-by: Mahesh Bandewar <maheshb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 0ff4eb3d5ebb ("neighbour: make proxy_queue.qlen limit
per-device") introduced the length counter qlen in struct neigh_parms.
There are separate neigh_parms instances for IPv4/ARP and IPv6/ND, and
while the family specific qlen is incremented in pneigh_enqueue(), the
mentioned commit decrements always the IPv4/ARP specific qlen,
regardless of the currently processed family, in pneigh_queue_purge()
and neigh_proxy_process().
As a result, with IPv6/ND, the family specific qlen is only incremented
(and never decremented) until it exceeds PROXY_QLEN, and then, according
to the check in pneigh_enqueue(), neighbor solicitations are not
answered anymore. As an example, this is noted when using the
subnet-router anycast address to access a Linux router. After a certain
amount of time (in the observed case, qlen exceeded PROXY_QLEN after two
days), the Linux router stops answering neighbor solicitations for its
subnet-router anycast address and effectively becomes unreachable.
Another result with IPv6/ND is that the IPv4/ARP specific qlen is
decremented more often than incremented. This leads to negative qlen
values, as a signed integer has been used for the length counter qlen,
and potentially to an integer overflow.
Fix this by introducing the helper function neigh_parms_qlen_dec(),
which decrements the family specific qlen. Thereby, make use of the
existing helper function neigh_get_dev_parms_rcu(), whose definition
therefore needs to be placed earlier in neighbour.c. Take the family
member from struct neigh_table to determine the currently processed
family and appropriately call neigh_parms_qlen_dec() from
pneigh_queue_purge() and neigh_proxy_process().
Additionally, use an unsigned integer for the length counter qlen.
Fixes: 0ff4eb3d5ebb ("neighbour: make proxy_queue.qlen limit per-device") Signed-off-by: Thomas Zeitlhofer <thomas.zeitlhofer+lkml@ze-it.at> Signed-off-by: David S. Miller <davem@davemloft.net>
Leon Romanovsky [Tue, 15 Nov 2022 17:34:39 +0000 (19:34 +0200)]
net: liquidio: simplify if expression
Fix the warning reported by kbuild:
cocci warnings: (new ones prefixed by >>)
>> drivers/net/ethernet/cavium/liquidio/lio_main.c:1797:54-56: WARNING !A || A && B is equivalent to !A || B
drivers/net/ethernet/cavium/liquidio/lio_main.c:1827:54-56: WARNING !A || A && B is equivalent to !A || B
Fixes: 8979f428a4af ("net: liquidio: release resources when liquidio driver open failed") Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Leon Romanovsky <leonro@nvidia.com> Reviewed-by: Saeed Mahameed <saeed@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Matthieu Baerts [Tue, 15 Nov 2022 22:10:45 +0000 (14:10 -0800)]
selftests: mptcp: run mptcp_sockopt from a new netns
Not running it from a new netns causes issues if some MPTCP settings are
modified, e.g. if MPTCP is disabled from the sysctl knob, if multiple
addresses are available and added to the MPTCP path-manager, etc.
In these cases, the created connection will not behave as expected, e.g.
unable to create an MPTCP socket, more than one subflow is seen, etc.
A new "sandbox" net namespace is now created and used to run
mptcp_sockopt from this controlled environment.
Fixes: ce9979129a0b ("selftests: mptcp: add mptcp getsockopt test cases") Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Paolo Abeni [Tue, 15 Nov 2022 22:10:44 +0000 (14:10 -0800)]
selftests: mptcp: gives slow test-case more time
On slow or busy VM, some test-cases still fail because the
data transfer completes before the endpoint manipulation
actually took effect.
Address the issue by artificially increasing the runtime for
the relevant test-cases.
Fixes: ef360019db40 ("selftests: mptcp: signal addresses testcases") Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/309 Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Hangbin Liu [Tue, 15 Nov 2022 14:24:00 +0000 (22:24 +0800)]
net: use struct_group to copy ip/ipv6 header addresses
kernel test robot reported warnings when build bonding module with
make W=1 O=build_dir ARCH=x86_64 SHELL=/bin/bash drivers/net/bonding/:
from ../drivers/net/bonding/bond_main.c:35:
In function ‘fortify_memcpy_chk’,
inlined from ‘iph_to_flow_copy_v4addrs’ at ../include/net/ip.h:566:2,
inlined from ‘bond_flow_ip’ at ../drivers/net/bonding/bond_main.c:3984:3:
../include/linux/fortify-string.h:413:25: warning: call to ‘__read_overflow2_field’ declared with attribute warning: detected read beyond size of f
ield (2nd parameter); maybe use struct_group()? [-Wattribute-warning]
413 | __read_overflow2_field(q_size_field, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In function ‘fortify_memcpy_chk’,
inlined from ‘iph_to_flow_copy_v6addrs’ at ../include/net/ipv6.h:900:2,
inlined from ‘bond_flow_ip’ at ../drivers/net/bonding/bond_main.c:3994:3:
../include/linux/fortify-string.h:413:25: warning: call to ‘__read_overflow2_field’ declared with attribute warning: detected read beyond size of f
ield (2nd parameter); maybe use struct_group()? [-Wattribute-warning]
413 | __read_overflow2_field(q_size_field, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
This is because we try to copy the whole ip/ip6 address to the flow_key,
while we only point the to ip/ip6 saddr. Note that since these are UAPI
headers, __struct_group() is used to avoid the compiler warnings.
Reported-by: kernel test robot <lkp@intel.com> Fixes: c3f8324188fa ("net: Add full IPv6 addresses to flow_keys") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Link: https://lore.kernel.org/r/20221115142400.1204786-1-liuhangbin@gmail.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
An external PHY needs settling time after power up or reset.
In the bind() function an mdio bus is registered. If at this point
the external PHY is still initialising, no valid PHY ID will be
read and on phy_find_first() the bind() function will fail.
If an external PHY is present, wait the maximum time specified
in 802.3 45.2.7.1.1.
Linus Torvalds [Wed, 16 Nov 2022 18:49:06 +0000 (10:49 -0800)]
Merge tag 'for-linus-6.1-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
"Two trivial cleanups, and three simple fixes"
* tag 'for-linus-6.1-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/platform-pci: use define instead of literal number
xen/platform-pci: add missing free_irq() in error path
xen-pciback: Allow setting PCI_MSIX_FLAGS_MASKALL too
xen/pcpu: fix possible memory leak in register_pcpu()
x86/xen: Use kstrtobool() instead of strtobool()
Linus Torvalds [Wed, 16 Nov 2022 18:40:00 +0000 (10:40 -0800)]
Merge tag 'pinctrl-v6.1-4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"Aere is a hopefully final round of pin control fixes. Nothing special,
driver fixes and we caught a potential NULL pointer exception.
- Fix a potential NULL dereference in the core!
- Fix all pin mux routes in the Rockchop PX30 driver
- Fix the UFS pins in the Qualcomm SC8280XP driver
- Fix bias disabling in the Mediatek driver
- Fix debounce time settings in the Mediatek driver"
* tag 'pinctrl-v6.1-4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: mediatek: Export debounce time tables
pinctrl: mediatek: Fix EINT pins input debounce time configuration
pinctrl: devicetree: fix null pointer dereferencing in pinctrl_dt_to_map
pinctrl: mediatek: common-v2: Fix bias-disable for PULL_PU_PD_RSEL_TYPE
pinctrl: qcom: sc8280xp: Rectify UFS reset pins
pinctrl: rockchip: list all pins in a possible mux route for PX30
Linus Torvalds [Wed, 16 Nov 2022 18:36:13 +0000 (10:36 -0800)]
Merge tag 'platform-drivers-x86-v6.1-4' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver fixes from Hans de Goede:
- Surface Pro 9 and Surface Laptop 5 kbd, battery, etc support (this
is just a few hw-id additions)
- A couple of other hw-id / DMI-quirk additions
- A few small bug fixes + 1 build fix
* tag 'platform-drivers-x86-v6.1-4' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
platform/x86: ideapad-laptop: Add module parameters to match DMI quirk tables
platform/x86: ideapad-laptop: Fix interrupt storm on fn-lock toggle on some Yoga laptops
platform/x86: hp-wmi: Ignore Smart Experience App event
platform/surface: aggregator_registry: Add support for Surface Laptop 5
platform/surface: aggregator_registry: Add support for Surface Pro 9
platform/surface: aggregator: Do not check for repeated unsequenced packets
platform/x86: acer-wmi: Enable SW_TABLET_MODE on Switch V 10 (SW5-017)
platform/x86: asus-wmi: add missing pci_dev_put() in asus_wmi_set_xusb2pr()
platform/x86/intel: pmc: Don't unconditionally attach Intel PMC when virtualized
platform/x86: thinkpad_acpi: Enable s2idle quirk for 21A1 machine type
platform/x86/amd: pmc: Add new ACPI ID AMDI0009
platform/x86/amd: pmc: Remove more CONFIG_DEBUG_FS checks
Gleb Mazovetskiy [Mon, 14 Nov 2022 22:56:16 +0000 (22:56 +0000)]
tcp: configurable source port perturb table size
On embedded systems with little memory and no relevant
security concerns, it is beneficial to reduce the size
of the table.
Reducing the size from 2^16 to 2^8 saves 255 KiB
of kernel RAM.
Makes the table size configurable as an expert option.
The size was previously increased from 2^8 to 2^16
in commit 4c2c8f03a5ab ("tcp: increase source port perturb table to
2^16").
Signed-off-by: Gleb Mazovetskiy <glex.spb@gmail.com> Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Sitnicki [Mon, 14 Nov 2022 19:16:19 +0000 (20:16 +0100)]
l2tp: Serialize access to sk_user_data with sk_callback_lock
sk->sk_user_data has multiple users, which are not compatible with each
other. Writers must synchronize by grabbing the sk->sk_callback_lock.
l2tp currently fails to grab the lock when modifying the underlying tunnel
socket fields. Fix it by adding appropriate locking.
We err on the side of safety and grab the sk_callback_lock also inside the
sk_destruct callback overridden by l2tp, even though there should be no
refs allowing access to the sock at the time when sk_destruct gets called.
v4:
- serialize write to sk_user_data in l2tp sk_destruct
v3:
- switch from sock lock to sk_callback_lock
- document write-protection for sk_user_data
v2:
- update Fixes to point to origin of the bug
- use real names in Reported/Tested-by tags
Cc: Tom Parkin <tparkin@katalix.com> Fixes: 3557baabf280 ("[L2TP]: PPP over L2TP driver core") Reported-by: Haowei Yan <g1042620637@gmail.com> Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yuan Can [Mon, 14 Nov 2022 14:22:25 +0000 (14:22 +0000)]
net: thunderbolt: Fix error handling in tbnet_init()
A problem about insmod thunderbolt-net failed is triggered with following
log given while lsmod does not show thunderbolt_net:
insmod: ERROR: could not insert module thunderbolt-net.ko: File exists
The reason is that tbnet_init() returns tb_register_service_driver()
directly without checking its return value, if tb_register_service_driver()
failed, it returns without removing property directory, resulting the
property directory can never be created later.
Fix by remove property directory when tb_register_service_driver() returns
error.
Fixes: e69b6c02b4c3 ("net: Add support for networking over Thunderbolt cable") Signed-off-by: Yuan Can <yuancan@huawei.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 16 Nov 2022 09:10:29 +0000 (09:10 +0000)]
Merge branch 'microchip-fixes'
Shang XiaoJing says:
====================
net: microchip: Fix potential null-ptr-deref due to create_singlethread_workqueue()
There are some functions call create_singlethread_workqueue() without
checking ret value, and the NULL workqueue_struct pointer may causes
null-ptr-deref. Will be fixed by this patch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Hans de Goede [Tue, 15 Nov 2022 19:34:00 +0000 (20:34 +0100)]
platform/x86: ideapad-laptop: Add module parameters to match DMI quirk tables
Add module parameters to allow setting the hw_rfkill_switch and
set_fn_lock_led feature flags for testing these on laptops which are not
on the DMI-id based allow lists for these 2 flags.
Arnav Rawat [Fri, 11 Nov 2022 14:32:09 +0000 (14:32 +0000)]
platform/x86: ideapad-laptop: Fix interrupt storm on fn-lock toggle on some Yoga laptops
Commit 3ae86d2d4704 ("platform/x86: ideapad-laptop: Fix Legion 5 Fn lock
LED") uses the WMI event-id for the fn-lock event on some Legion 5 laptops
to manually toggle the fn-lock LED because the EC does not do it itself.
However, the same WMI ID is also sent on some Yoga laptops. Here, setting
the fn-lock state is not valid behavior, and causes the EC to spam
interrupts until the laptop is rebooted.
Add a set_fn_lock_led_list[] DMI-id list and only enable the workaround to
manually set the LED on models on this list.
Maximilian Luz [Tue, 15 Nov 2022 23:14:40 +0000 (00:14 +0100)]
platform/surface: aggregator_registry: Add support for Surface Laptop 5
Add device nodes to enable support for battery and charger status, the
ACPI platform profile, as well as internal HID devices (including
touchpad and keyboard) on the Surface Laptop 5.
Vladimir Oltean [Mon, 14 Nov 2022 14:35:51 +0000 (16:35 +0200)]
net: dsa: don't leak tagger-owned storage on switch driver unbind
In the initial commit dc452a471dba ("net: dsa: introduce tagger-owned
storage for private and shared data"), we had a call to
tag_ops->disconnect(dst) issued from dsa_tree_free(), which is called at
tree teardown time.
There were problems with connecting to a switch tree as a whole, so this
got reworked to connecting to individual switches within the tree. In
this process, tag_ops->disconnect(ds) was made to be called only from
switch.c (cross-chip notifiers emitted as a result of dynamic tag proto
changes), but the normal driver teardown code path wasn't replaced with
anything.
Solve this problem by adding a function that does the opposite of
dsa_switch_setup_tag_protocol(), which is called from the equivalent
spot in dsa_switch_teardown(). The positioning here also ensures that we
won't have any use-after-free in tagging protocol (*rcv) ops, since the
teardown sequence is as follows:
dsa_tree_teardown
-> dsa_tree_teardown_master
-> dsa_master_teardown
-> unsets master->dsa_ptr, making no further packets match the
ETH_P_XDSA packet type handler
-> dsa_tree_teardown_ports
-> dsa_port_teardown
-> dsa_slave_destroy
-> unregisters DSA net devices, there is even a synchronize_net()
in unregister_netdevice_many()
-> dsa_tree_teardown_switches
-> dsa_switch_teardown
-> dsa_switch_teardown_tag_protocol
-> finally frees the tagger-owned storage
Fixes: 7f2973149c22 ("net: dsa: make tagging protocols connect to individual switches from a tree") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Saeed Mahameed <saeed@kernel.org> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Link: https://lore.kernel.org/r/20221114143551.1906361-1-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Wei Yongjun [Mon, 14 Nov 2022 11:05:19 +0000 (11:05 +0000)]
net/x25: Fix skb leak in x25_lapb_receive_frame()
x25_lapb_receive_frame() using skb_copy() to get a private copy of
skb, the new skb should be freed in the undersized/fragmented skb
error handling path. Otherwise there is a memory leak.
Liu Jian [Mon, 14 Nov 2022 09:55:49 +0000 (17:55 +0800)]
net: ag71xx: call phylink_disconnect_phy if ag71xx_hw_enable() fail in ag71xx_open()
If ag71xx_hw_enable() fails, call phylink_disconnect_phy() to clean up.
And if phylink_of_phy_connect() fails, nothing needs to be done.
Compile tested only.
Fixes: 892e09153fa3 ("net: ag71xx: port to phylink") Signed-off-by: Liu Jian <liujian56@huawei.com> Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://lore.kernel.org/r/20221114095549.40342-1-liujian56@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Linus Torvalds [Tue, 15 Nov 2022 22:56:23 +0000 (14:56 -0800)]
AMerge tag 'netfs-fixes-20221115' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
Pull netfx fixes from David Howells:
"Two fixes, affecting the functions that iterates over the pagecache
unmarking or unlocking pages after an op is complete:
- xas_for_each() loops must call xas_retry() first thing and
immediately do a "continue" in the case that the extracted value is
a special value that indicates that the walk raced with a
modification. Fix the unlock and unmark loops to do this.
- The maths in the unlock loop is dodgy as it could, theoretically,
at some point in the future end up with a starting file pointer
that is in the middle of a folio. This will cause a subtraction to
go negative - but the number is unsigned. Fix the maths to use
absolute file positions instead of relative page indices"
* tag 'netfs-fixes-20221115' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
netfs: Fix dodgy maths
netfs: Fix missing xas_retry() calls in xarray iteration
Linus Torvalds [Tue, 15 Nov 2022 18:30:34 +0000 (10:30 -0800)]
Merge tag 'erofs-for-6.1-rc6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs
Pull erofs fixes from Gao Xiang:
"Most patches randomly fix error paths or corner cases in fscache mode
reported recently. One fixes an invalid access relating to fragments
on crafted images.
Summary:
- Fix packed_inode invalid access when reading fragments on crafted
images
- Add a missing erofs_put_metabuf() in an error path in fscache mode
- Fix incorrect `count' for unmapped extents in fscache mode
- Fix use-after-free of fsid and domain_id string when remounting
- Fix missing xas_retry() in fscache mode"
* tag 'erofs-for-6.1-rc6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs:
erofs: fix missing xas_retry() in fscache mode
erofs: fix use-after-free of fsid and domain_id string
erofs: get correct count for unmapped range in fscache mode
erofs: put metabuf in error path in fscache mode
erofs: fix general protection fault when reading fragment
David Howells [Fri, 4 Nov 2022 15:36:49 +0000 (15:36 +0000)]
netfs: Fix dodgy maths
Fix the dodgy maths in netfs_rreq_unlock_folios(). start_page could be
inside the folio, in which case the calculation of pgpos will be come up
with a negative number (though for the moment rreq->start is rounded down
earlier and folios would have to get merged whilst locked)
Alter how this works to just frame the tracking in terms of absolute file
positions, rather than offsets from the start of the I/O request. This
simplifies the maths and makes it easier to follow.
Fix the issue by using folio_pos() and folio_size() to calculate the end
position of the page.
David Howells [Thu, 3 Nov 2022 16:08:14 +0000 (16:08 +0000)]
netfs: Fix missing xas_retry() calls in xarray iteration
netfslib has a number of places in which it performs iteration of an xarray
whilst being under the RCU read lock. It *should* call xas_retry() as the
first thing inside of the loop and do "continue" if it returns true in case
the xarray walker passed out a special value indicating that the walk needs
to be redone from the root[*].
Fix this by adding the missing retry checks.
[*] I wonder if this should be done inside xas_find(), xas_next_node() and
suchlike, but I'm told that's not an simple change to effect.
This can cause an oops like that below. Note the faulting address - this
is an internal value (|0x2) returned from xarray.
Changes:
========
ver #2)
- Changed an unsigned int to a size_t to reduce the likelihood of an
overflow as per Willy's suggestion.
- Added an additional patch to fix the maths.
Maximilian Luz [Sun, 13 Nov 2022 18:59:51 +0000 (19:59 +0100)]
platform/surface: aggregator_registry: Add support for Surface Pro 9
Add device nodes to enable support for battery and charger status, the
ACPI platform profile, as well as internal and type-cover HID devices
(including sensors, touchpad, keyboard, and other miscellaneous devices)
on the Surface Pro 9.
This does not include support for a tablet-mode switch yet, as that is
now handled via the POS subsystem (unlike the Surface Pro 8, where it is
handled via the KIP subsystem) and therefore needs further changes.
While we're at it, also add the missing comment for the Surface Pro 8.
Maximilian Luz [Sun, 13 Nov 2022 18:59:50 +0000 (19:59 +0100)]
platform/surface: aggregator: Do not check for repeated unsequenced packets
Currently, we check any received packet whether we have already seen it
previously, regardless of the packet type (sequenced / unsequenced). We
do this by checking the sequence number. This assumes that sequence
numbers are valid for both sequenced and unsequenced packets. However,
this assumption appears to be incorrect.
On some devices, the sequence number field of unsequenced packets (in
particular HID input events on the Surface Pro 9) is always zero. As a
result, the current retransmission check kicks in and discards all but
the first unsequenced packet, breaking (among other things) keyboard and
touchpad input.
Note that we have, so far, only seen packets being retransmitted in
sequenced communication. In particular, this happens when there is an
ACK timeout, causing the EC (or us) to re-send the packet waiting for an
ACK. Arguably, retransmission / duplication of unsequenced packets
should not be an issue as there is no logical condition (such as an ACK
timeout) to determine when a packet should be sent again.
Therefore, remove the retransmission check for unsequenced packets
entirely to resolve the issue.
Fixes: c167b9c7e3d6 ("platform/surface: Add Surface Aggregator subsystem") Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com> Link: https://lore.kernel.org/r/20221113185951.224759-1-luzmaximilian@gmail.com Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Xiongfeng Wang [Fri, 11 Nov 2022 10:07:52 +0000 (18:07 +0800)]
platform/x86: asus-wmi: add missing pci_dev_put() in asus_wmi_set_xusb2pr()
pci_get_device() will increase the reference count for the returned
pci_dev. We need to use pci_dev_put() to decrease the reference count
before asus_wmi_set_xusb2pr() returns.
Roger Pau Monné [Thu, 10 Nov 2022 16:31:44 +0000 (17:31 +0100)]
platform/x86/intel: pmc: Don't unconditionally attach Intel PMC when virtualized
The current logic in the Intel PMC driver will forcefully attach it
when detecting any CPU on the intel_pmc_core_platform_ids array,
even if the matching ACPI device is not present.
There's no checking in pmc_core_probe() to assert that the PMC device
is present, and hence on virtualized environments the PMC device
probes successfully, even if the underlying registers are not present.
Before commit 21ae43570940 ("platform/x86: intel_pmc_core: Substitute PCI
with CPUID enumeration") the driver would check for the presence of a
specific PCI device, and that prevented the driver from attaching when
running virtualized.
Fix by only forcefully attaching the PMC device when not running
virtualized. Note that virtualized platforms can still get the device
to load if the appropriate ACPI device is present on the tables
provided to the VM.
Make an exception for the Xen initial domain, which does have full
hardware access, and hence can attach to the PMC if present.
Fixes: 21ae43570940 ("platform/x86: intel_pmc_core: Substitute PCI with CPUID enumeration") Signed-off-by: Roger Pau Monné <roger.pau@citrix.com> Acked-by: David E. Box <david.e.box@linux.intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20221110163145.80374-1-roger.pau@citrix.com Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Lennard Gäher [Tue, 8 Nov 2022 07:20:23 +0000 (08:20 +0100)]
platform/x86: thinkpad_acpi: Enable s2idle quirk for 21A1 machine type
Previously, the s2idle quirk was only active for the 21A0 machine type
of the P14s Gen2a product. This also enables it for the second 21A1 type,
thus reducing wake-up times from s2idle.
Add new a new ACPI ID AMDI0009 used by upcoming AMD platform to the pmc
supported list of devices.
Cc: stable@vger.kernel.org # 6.0 Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com> Reviewed-by: Mario Limonciello <mario.limonciello@amd.com> Link: https://lore.kernel.org/r/20221109083346.361603-1-Shyam-sundar.S-k@amd.com Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Ido Schimmel [Mon, 14 Nov 2022 08:45:09 +0000 (10:45 +0200)]
bridge: switchdev: Fix memory leaks when changing VLAN protocol
The bridge driver can offload VLANs to the underlying hardware either
via switchdev or the 8021q driver. When the former is used, the VLAN is
marked in the bridge driver with the 'BR_VLFLAG_ADDED_BY_SWITCHDEV'
private flag.
To avoid the memory leaks mentioned in the cited commit, the bridge
driver will try to delete a VLAN via the 8021q driver if the VLAN is not
marked with the previously mentioned flag.
When the VLAN protocol of the bridge changes, switchdev drivers are
notified via the 'SWITCHDEV_ATTR_ID_BRIDGE_VLAN_PROTOCOL' attribute, but
the 8021q driver is also called to add the existing VLANs with the new
protocol and delete them with the old protocol.
In case the VLANs were offloaded via switchdev, the above behavior is
both redundant and buggy. Redundant because the VLANs are already
programmed in hardware and drivers that support VLAN protocol change
(currently only mlx5) change the protocol upon the switchdev attribute
notification. Buggy because the 8021q driver is called despite these
VLANs being marked with 'BR_VLFLAG_ADDED_BY_SWITCHDEV'. This leads to
memory leaks [1] when the VLANs are deleted.
Fix by not calling the 8021q driver for VLANs that were already
programmed via switchdev.
====================
net: hns3: This series bugfix for the HNS3 ethernet driver.
This series includes some bugfix for the HNS3 ethernet driver.
Patch 1# fix incorrect hw rss hash type of rx packet. Fixes: 796640778c26 ("net: hns3: support RXD advanced layout") Fixes: 232fc64b6e62 ("net: hns3: Add HW RSS hash information to RX skb") Fixes: ea4858670717 ("net: hns3: handle the BD info on the last BD of the packet")
Patch 2# fix return value check bug of rx copybreak. Fixes: e74a726da2c4 ("net: hns3: refactor hns3_nic_reuse_page()") Fixes: 99f6b5fb5f63 ("net: hns3: use bounce buffer when rx page can not be reused")
Patch 3# net: hns3: fix setting incorrect phy link ksettings
for firmware in resetting process Fixes: f5f2b3e4dcc0 ("net: hns3: add support for imp-controlled PHYs") Fixes: c5ef83cbb1e9 ("net: hns3: fix for phy_addr error in hclge_mac_mdio_config") Fixes: 2312e050f42b ("net: hns3: Fix for deadlock problem occurring when unregistering ae_algo")
====================
Guangbin Huang [Mon, 14 Nov 2022 08:20:48 +0000 (16:20 +0800)]
net: hns3: fix setting incorrect phy link ksettings for firmware in resetting process
Currently, if driver is in phy-imp(phy controlled by imp firmware) mode, as
driver did not update phy link ksettings after initialization process or
not update advertising when getting phy link ksettings from firmware, it
may set incorrect phy link ksettings for firmware in resetting process.
So fix it.
Fixes: f5f2b3e4dcc0 ("net: hns3: add support for imp-controlled PHYs") Fixes: c5ef83cbb1e9 ("net: hns3: fix for phy_addr error in hclge_mac_mdio_config") Fixes: 2312e050f42b ("net: hns3: Fix for deadlock problem occurring when unregistering ae_algo") Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: Hao Lan <lanhao@huawei.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Jie Wang [Mon, 14 Nov 2022 08:20:47 +0000 (16:20 +0800)]
net: hns3: fix return value check bug of rx copybreak
The refactoring of rx copybreak modifies the original return logic, which
will make this feature unavailable. So this patch fixes the return logic of
rx copybreak.
Fixes: e74a726da2c4 ("net: hns3: refactor hns3_nic_reuse_page()") Fixes: 99f6b5fb5f63 ("net: hns3: use bounce buffer when rx page can not be reused") Signed-off-by: Jie Wang <wangjie125@huawei.com> Signed-off-by: Hao Lan <lanhao@huawei.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Jian Shen [Mon, 14 Nov 2022 08:20:46 +0000 (16:20 +0800)]
net: hns3: fix incorrect hw rss hash type of rx packet
Currently, the HNS3 driver reports the rss hash type
of each packet based on the rss hash tuples set. It
always reports PKT_HASH_TYPE_L4, without checking the
type of current packet. It's incorrect.
Fixes it by reporting it base on the packet type.
Fixes: 796640778c26 ("net: hns3: support RXD advanced layout") Fixes: 232fc64b6e62 ("net: hns3: Add HW RSS hash information to RX skb") Fixes: ea4858670717 ("net: hns3: handle the BD info on the last BD of the packet") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Hao Lan <lanhao@huawei.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Yuan Can [Mon, 14 Nov 2022 02:56:59 +0000 (02:56 +0000)]
net: ena: Fix error handling in ena_init()
The ena_init() won't destroy workqueue created by
create_singlethread_workqueue() when pci_register_driver() failed.
Call destroy_workqueue() when pci_register_driver() failed to prevent the
resource leak.
Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by: Yuan Can <yuancan@huawei.com> Acked-by: Shay Agroskin <shayagr@amazon.com> Link: https://lore.kernel.org/r/20221114025659.124726-1-yuancan@huawei.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Cong Wang [Mon, 14 Nov 2022 00:51:19 +0000 (16:51 -0800)]
kcm: close race conditions on sk_receive_queue
sk->sk_receive_queue is protected by skb queue lock, but for KCM
sockets its RX path takes mux->rx_lock to protect more than just
skb queue. However, kcm_recvmsg() still only grabs the skb queue
lock, so race conditions still exist.
We can teach kcm_recvmsg() to grab mux->rx_lock too but this would
introduce a potential performance regression as struct kcm_mux can
be shared by multiple KCM sockets.
So we have to enforce skb queue lock in requeue_rx_msgs() and handle
skb peek case carefully in kcm_wait_data(). Fortunately,
skb_recv_datagram() already handles it nicely and is widely used by
other sockets, we can just switch to skb_recv_datagram() after
getting rid of the unnecessary sock lock in kcm_recvmsg() and
kcm_splice_read(). Side note: SOCK_DONE is not used by KCM sockets,
so it is safe to get rid of this check too.
I ran the original syzbot reproducer for 30 min without seeing any
issue.
Fixes: ab7ac4eb9832 ("kcm: Kernel Connection Multiplexor module") Reported-by: syzbot+278279efdd2730dd14bf@syzkaller.appspotmail.com Reported-by: shaozhengchao <shaozhengchao@huawei.com> Cc: Paolo Abeni <pabeni@redhat.com> Cc: Tom Herbert <tom@herbertland.com> Signed-off-by: Cong Wang <cong.wang@bytedance.com> Link: https://lore.kernel.org/r/20221114005119.597905-1-xiyou.wangcong@gmail.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
platform/x86/amd: pmc: Remove more CONFIG_DEBUG_FS checks
commit b37fe34c8309 ("platform/x86/amd: pmc: remove CONFIG_DEBUG_FS
checks") removed most CONFIG_DEBUG_FS checks, but there were some
left that were reported to cause compile test failures.
Remove the remaining checks, and also the unnecessary CONFIG_SUSPEND
used in the same place.
Linus Walleij [Tue, 15 Nov 2022 08:11:07 +0000 (09:11 +0100)]
pinctrl: mediatek: Export debounce time tables
The kernel test robot complains that in certain combinations
when building the Mediatek drivers as modules we lack some
debounce table symbols, so export them.
Reported-by: kernel test robot <lkp@intel.com> Fixes: e1ff91f9d230 ("pinctrl: mediatek: Fix EINT pins input debounce time configuration") Cc: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Yuan Can [Sun, 13 Nov 2022 09:29:29 +0000 (09:29 +0000)]
net: ionic: Fix error handling in ionic_init_module()
A problem about ionic create debugfs failed is triggered with the
following log given:
[ 415.799514] debugfs: Directory 'ionic' with parent '/' already present!
The reason is that ionic_init_module() returns ionic_bus_register_driver()
directly without checking its return value, if ionic_bus_register_driver()
failed, it returns without destroy the newly created debugfs, resulting
the debugfs of ionic can never be created later.
Amit Cohen [Fri, 11 Nov 2022 17:03:27 +0000 (18:03 +0100)]
mlxsw: Avoid warnings when not offloaded FDB entry with IPv6 is removed
FDB entries that perform VXLAN encapsulation with an IPv6 underlay hold
a reference on a resource - the KVDL entry where the IPv6 underlay
destination IP is stored. For that, the driver maintains two hash tables:
1. Maps IPv6 to KVDL index
2. Maps {MAC, FID index} to IPv6 address
When a FDB entry is removed, the second table is used to find the relevant
IPv6 address and the first table is used to remove the reference count and
free the index if is not used anymore.
In order for a packet to be forwarded to a single remote VTEP, FDB
entries need to be configured at both the bridge and VXLAN devices' FDB
tables. Both entries are squashed into one {MAC, VLAN/VNI} -> IP entry
in the hardware. Therefore, in case one entry is removed, the entry will
be removed from the hardware and the remaining entry will be unmarked
with 'offload' flag since it is not offloaded anymore.
For example, the two FDB entries should be added to allow packets to be
forwarded via vx10:
$ bridge fdb add dev vx10 aa:bb:cc:dd:ee:ff self static dst 2001:db8:5::1
$ bridge fdb add dev vx10 aa:bb:cc:dd:ee:ff master static vlan 10
When one entry will be removed, the second one will not be offloaded
anymore. When the first entry (in VXLAN FDB) will be removed / will not be
offloaded anymore, the two mappings in IPv6 hash tables will be removed.
In case that the second entry is removed before the first one, unexpected
warnings[1][2] will be shown in user space as a result of removing the
first entry. The issue is that not offloaded entry is removed, the driver
tries to search the relevant entries in the hash tables, does not find them
and therefore warns.
Do not handle removing of not offloaded VXLAN FDB entries, as they were
already removed when the offload flag was removed.
Linus Torvalds [Mon, 14 Nov 2022 20:40:51 +0000 (12:40 -0800)]
Merge tag 'vfio-v6.1-rc6' of https://github.com/awilliam/linux-vfio
Pull VFIO fixes from Alex Williamson:
- Fixes for potential container registration leak for drivers not
implementing a close callback, duplicate container de-registrations,
and a regression in support for bus reset on last device close from
a device set (Anthony DeRossi)
* tag 'vfio-v6.1-rc6' of https://github.com/awilliam/linux-vfio:
vfio/pci: Check the device set open count on reset
vfio: Export the device set open count
vfio: Fix container device registration life cycle
Linus Torvalds [Mon, 14 Nov 2022 20:00:03 +0000 (12:00 -0800)]
Merge tag 'mtd/fixes-for-6.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull mtd fixes from Miquel Raynal:
- Placate "$VARIABLE is used uninitialized" warnings
- omap2: Add missing dependency on GPMC
- qcom: Handle ret from parse with codeword_fixup
* tag 'mtd/fixes-for-6.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux:
mtd: onenand: omap2: add dependency on GPMC
mtd: rawnand: placate "$VARIABLE is used uninitialized" warnings
mtd: rawnand: qcom: handle ret from parse with codeword_fixup
Jingbo Xu [Mon, 14 Nov 2022 12:19:43 +0000 (20:19 +0800)]
erofs: fix missing xas_retry() in fscache mode
The xarray iteration only holds the RCU read lock and thus may encounter
XA_RETRY_ENTRY if there's process modifying the xarray concurrently.
This will cause oops when referring to the invalid entry.
Fix this by adding the missing xas_retry(), which will make the
iteration wind back to the root node if XA_RETRY_ENTRY is encountered.
Fixes: d435d53228dd ("erofs: change to use asynchronous io for fscache readpage/readahead") Suggested-by: David Howells <dhowells@redhat.com> Reviewed-by: Gao Xiang <hsiangkao@linux.alibaba.com> Reviewed-by: Jia Zhu <zhujia.zj@bytedance.com> Signed-off-by: Jingbo Xu <jefflexu@linux.alibaba.com> Link: https://lore.kernel.org/r/20221114121943.29987-1-jefflexu@linux.alibaba.com Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
pinctrl: mediatek: Fix EINT pins input debounce time configuration
The External Interrupt Controller (EINTC) on all of the supported
MediaTek SoCs does support input debouncing, but not all of them
index the debounce time values (DBNC_SETTING registers) the same way.
Before this change, in some cases, as an example, requesting a debounce
time of 16 milliseconds would mistakenly set the relative DBNC_SETTING
register to 0x2, resulting in a way shorter debounce time of 500uS.
To fix the aforementioned issue, define three different debounce_time
arrays, reflecting the correct register index for each value and for
each register index variant, and make sure that each SoC pinctrl
driver uses the right one.
xen-pciback: Allow setting PCI_MSIX_FLAGS_MASKALL too
When Xen domain configures MSI-X, the usual approach is to enable MSI-X
together with masking all of them via the config space, then fill the
table and only then clear PCI_MSIX_FLAGS_MASKALL. Allow doing this via
QEMU running in a stub domain.
Previously, when changing PCI_MSIX_FLAGS_MASKALL was not allowed, the
whole write was aborted, preventing change to the PCI_MSIX_FLAGS_ENABLE
bit too.
Note the Xen hypervisor intercepts this write anyway, and may keep the
PCI_MSIX_FLAGS_MASKALL bit set if it wishes to. It will store the
guest-requested state and will apply it eventually.
Yang Yingliang [Thu, 10 Nov 2022 15:24:41 +0000 (23:24 +0800)]
xen/pcpu: fix possible memory leak in register_pcpu()
In device_add(), dev_set_name() is called to allocate name, if it returns
error, the name need be freed. As comment of device_register() says, it
should use put_device() to give up the reference in the error path. So fix
this by calling put_device(), then the name can be freed in kobject_cleanup().
Vladimir Oltean [Fri, 11 Nov 2022 21:10:20 +0000 (23:10 +0200)]
net: dsa: make dsa_master_ioctl() see through port_hwtstamp_get() shims
There are multi-generational drivers like mv88e6xxx which have code like
this:
int mv88e6xxx_port_hwtstamp_get(struct dsa_switch *ds, int port,
struct ifreq *ifr)
{
if (!chip->info->ptp_support)
return -EOPNOTSUPP;
...
}
DSA wants to deny PTP timestamping on the master if the switch supports
timestamping too. However it currently relies on the presence of the
port_hwtstamp_get() callback to determine PTP capability, and this
clearly does not work in that case (method is present but returns
-EOPNOTSUPP).
We should not deny PTP on the DSA master for those switches which truly
do not support hardware timestamping.
Create a dsa_port_supports_hwtstamp() method which actually probes for
support by calling port_hwtstamp_get() and seeing whether that returned
-EOPNOTSUPP or not.
Fixes: f685e609a301 ("net: dsa: Deny PTP on master if switch supports it") Link: https://patchwork.kernel.org/project/netdevbpf/patch/20221110124345.3901389-1-festevam@gmail.com/ Reported-by: Fabio Estevam <festevam@gmail.com> Reported-by: Steffen Bätz <steffen@innosonix.de> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Tested-by: Fabio Estevam <festevam@denx.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Yongjun [Fri, 11 Nov 2022 09:20:44 +0000 (09:20 +0000)]
net: mhi: Fix memory leak in mhi_net_dellink()
MHI driver registers network device without setting the
needs_free_netdev flag, and does NOT call free_netdev() when
unregisters network device, which causes a memory leak.
This patch calls free_netdev() to fix it since netdev_priv
is used after unregister.
Fixes: 13adac032982 ("net: mhi_net: Register wwan_ops for link creation") Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ziyang Xuan [Fri, 11 Nov 2022 07:09:35 +0000 (15:09 +0800)]
octeon_ep: ensure get mac address successfully before eth_hw_addr_set()
octep_get_mac_addr() can fail because send mbox message failed. If this
happens, octep_dev->mac_addr will be zero. It should not continue to
initialize. Add exception handling for octep_get_mac_addr() to fix it.
Fixes: 862cd659a6fb ("octeon_ep: Add driver framework and device initialization") Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ziyang Xuan [Fri, 11 Nov 2022 07:09:23 +0000 (15:09 +0800)]
octeon_ep: fix potential memory leak in octep_device_setup()
When occur unsupported_dev and mbox init errors, it did not free oct->conf
and iounmap() oct->mmio[i].hw_addr. That would trigger memory leak problem.
Add kfree() for oct->conf and iounmap() for oct->mmio[i].hw_addr under
unsupported_dev and mbox init errors to fix the problem.
Fixes: 862cd659a6fb ("octeon_ep: Add driver framework and device initialization") Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ziyang Xuan [Fri, 11 Nov 2022 07:08:47 +0000 (15:08 +0800)]
octeon_ep: ensure octep_get_link_status() successfully before octep_link_up()
octep_get_link_status() can fail because send mbox message failed, then
octep_get_link_status() will return ret less than 0. Excute octep_link_up()
as long as ret is not equal to 0 in octep_open() now. That is not correct.
The value type of link.state is enum octep_ctrl_net_state. Positive value
represents up. Excute octep_link_up() when ret is bigger than 0.
Fixes: 862cd659a6fb ("octeon_ep: Add driver framework and device initialization") Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ziyang Xuan [Fri, 11 Nov 2022 07:08:27 +0000 (15:08 +0800)]
octeon_ep: delete unnecessary napi rollback under set_queues_err in octep_open()
octep_napi_add() and octep_napi_enable() are all after
netif_set_real_num_{tx,rx}_queues() in octep_open(), so it is unnecessary
napi rollback under set_queues_err. Delete them to fix it.
Fixes: 37d79d059606 ("octeon_ep: add Tx/Rx processing and interrupt support") Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Gaosheng Cui [Fri, 11 Nov 2022 07:04:33 +0000 (15:04 +0800)]
bnxt_en: Remove debugfs when pci_register_driver failed
When pci_register_driver failed, we need to remove debugfs,
which will caused a resource leak, fix it.
Resource leak logs as follows:
[ 52.184456] debugfs: Directory 'bnxt_en' with parent '/' already present!
Fixes: cabfb09d87bd ("bnxt_en: add debugfs support for DIM") Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Reviewed-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Zhengchao Shao [Fri, 11 Nov 2022 01:47:34 +0000 (09:47 +0800)]
net: caif: fix double disconnect client in chnl_net_open()
When connecting to client timeout, disconnect client for twice in
chnl_net_open(). Remove one. Compile tested only.
Fixes: 2aa40aef9deb ("caif: Use link layer MTU instead of fixed MTU") Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Chuang Wang [Fri, 11 Nov 2022 01:41:30 +0000 (09:41 +0800)]
net: macvlan: Use built-in RCU list checking
hlist_for_each_entry_rcu() has built-in RCU and lock checking.
Pass cond argument to hlist_for_each_entry_rcu() to silence false
lockdep warning when CONFIG_PROVE_RCU_LIST is enabled.
Execute as follow:
ip link add link eth0 type macvlan mode source macaddr add <MAC-ADDR>
The rtnl_lock is held when macvlan_hash_lookup_source() or
macvlan_fill_info_macaddr() are called in the non-RCU read side section.
So, pass lockdep_rtnl_is_held() to silence false lockdep warning.
Fixes: 79cf79abce71 ("macvlan: add source mode") Signed-off-by: Chuang Wang <nashuiliang@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wang ShaoBo [Thu, 10 Nov 2022 11:38:23 +0000 (19:38 +0800)]
mISDN: fix misuse of put_device() in mISDN_register_device()
We should not release reference by put_device() before calling device_initialize().
Fixes: e7d1d4d9ac0d ("mISDN: fix possible memory leak in mISDN_register_device()") Signed-off-by: Wang ShaoBo <bobo.shaobowang@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Zhengchao Shao [Thu, 10 Nov 2022 10:30:37 +0000 (18:30 +0800)]
net: liquidio: release resources when liquidio driver open failed
When liquidio driver open failed, it doesn't release resources. Compile
tested only.
Fixes: 5b07aee11227 ("liquidio: MSIX support for CN23XX") Fixes: dbc97bfd3918 ("net: liquidio: Add missing null pointer checks") Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 13 Nov 2022 15:57:33 +0000 (07:57 -0800)]
Merge tag 'mips-fixes_6.1_1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS fixes from Thomas Bogendoerfer:
- fix jump label branch range check
- check kmalloc failures in Loongson64 kexec
- fix builds with clang-14
- fix char/int handling in pic32
* tag 'mips-fixes_6.1_1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MIPS: pic32: treat port as signed integer
MIPS: jump_label: Fix compat branch range check
mips: alchemy: gpio: Include the right header
MIPS: Loongson64: Add WARN_ON on kexec related kmalloc failed
MIPS: fix duplicate definitions for exported symbols
mips: boot/compressed: use __NO_FORTIFY
Linus Torvalds [Sun, 13 Nov 2022 15:52:22 +0000 (07:52 -0800)]
Merge tag 'efi-fixes-for-v6.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi
Pull EFI fixes from Ard Biesheuvel:
- Force the use of SetVirtualAddressMap() on Ampera Altra arm64
machines, which crash in SetTime() if no virtual remapping is used
This is the first time we've added an SMBIOS based quirk on arm64,
but fortunately, we can just call a EFI protocol to grab the type #1
SMBIOS record when running in the stub, so we don't need all the
machinery we have in the kernel proper to parse SMBIOS data.
- Drop a spurious warning on misaligned runtime regions when using 16k
or 64k pages on arm64
* tag 'efi-fixes-for-v6.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi:
arm64: efi: Fix handling of misaligned runtime regions and drop warning
arm64: efi: Force the use of SetVirtualAddressMap() on Altra machines
Linus Torvalds [Sat, 12 Nov 2022 17:27:15 +0000 (09:27 -0800)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Three small fixes, all in drivers.
The sas one is in an unlikely error leg, the debug one is to make it
more standards conformant and the ibmvfc one is to fix a user visible
bug where a failover could lose all paths to the device"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: scsi_debug: Make the READ CAPACITY response compliant with ZBC
scsi: scsi_transport_sas: Fix error handling in sas_phy_add()
scsi: ibmvfc: Avoid path failures during live migration
Takashi Iwai [Sat, 12 Nov 2022 08:47:18 +0000 (09:47 +0100)]
ALSA: memalloc: Try dma_alloc_noncontiguous() at first
The latest fix for the non-contiguous memalloc helper changed the
allocation method for a non-IOMMU system to use only the fallback
allocator. This should have worked, but it caused a problem sometimes
when too many non-contiguous pages are allocated that can't be treated
by HD-audio controller.
As a quirk workaround, go back to the original strategy: use
dma_alloc_noncontiguous() at first, and apply the fallback only when
it fails, but only for non-IOMMU case.
We'll need a better fix in the fallback code as well, but this
workaround should paper over most cases.
Linus Torvalds [Sat, 12 Nov 2022 04:27:13 +0000 (20:27 -0800)]
Merge tag 'ata-6.1-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata
Pull ata fixes from Damien Le Moal:
"Several libata generic code fixes for rc5:
- Add missing translation of the SYNCHRONIZE CACHE 16 scsi command as
this command is mandatory for host-managed ZBC drives.
The lack of support for it in libata-scsi was causing issues with
some passthrough applications using ZBC drives (from Shin'ichiro).
- Fix the error path of libata-transport host, port, link and device
attributes initialization (from Yingliang).
- Prevent issuing new commands to a drive that is in the NCQ error
state and undergoing recovery (From Niklas).
This bug went unnoticed for a long time as commands issued to a
drive in error state are aborted immediately and retried by the
scsi layer, hiding the useless abort-and-retry sequence"
* tag 'ata-6.1-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata:
ata: libata-core: do not issue non-internal commands once EH is pending
ata: libata-transport: fix error handling in ata_tdev_add()
ata: libata-transport: fix error handling in ata_tlink_add()
ata: libata-transport: fix error handling in ata_tport_add()
ata: libata-transport: fix double ata_host_put() in ata_tport_add()
ata: libata-scsi: fix SYNCHRONIZE CACHE (16) command failure
We're currently hitting the WARN_ON in mctp_i2c_flow_release:
if (midev->release_count > midev->i2c_lock_count) {
WARN_ONCE(1, "release count overflow");
This may be hit if we expire a flow before sending the first packet it
contains - as we will not be pairing the increment of release_count
(performed on flow release) with the i2c lock operation (only
performed on actual TX).
To fix this, only release a flow if we've encountered it previously (ie,
dev_flow_state does not indicate NEW), as we will mark the flow as
ACTIVE at the same time as accounting for the i2c lock operation. We
also need to add an INVALID flow state, to indicate when we've done the
release.
Yu Liao [Thu, 10 Nov 2022 09:03:29 +0000 (17:03 +0800)]
net/tls: Fix memory leak in tls_enc_skb() and tls_sw_fallback_init()
'aead_req' and 'aead_send' is allocated but not freed in default switch
case. This commit fixes the potential memory leak by freeing them under
the situation.
Note that the default cases here should never be reached as they'd
mean we allowed offloading an unsupported algorithm.
net: stmmac: ensure tx function is not running in stmmac_xdp_release()
When stmmac_xdp_release() is called, there is a possibility that tx
function is still running on other queues which will lead to tx queue
timed out and reset adapter.
This commit ensure that tx function is not running xdp before release
flow continue to run.
Fixes: ac746c8520d9 ("net: stmmac: enhance XDP ZC driver level switching performance") Signed-off-by: Song Yoong Siang <yoong.siang.song@intel.com> Signed-off-by: Mohd Faizal Abdul Rahim <faizal.abdul.rahim@intel.com> Signed-off-by: Noor Azura Ahmad Tarmizi <noor.azura.ahmad.tarmizi@intel.com> Link: https://lore.kernel.org/r/20221110064552.22504-1-noor.azura.ahmad.tarmizi@linux.intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
net: phy: dp83867: Fix SGMII FIFO depth for non OF devices
Current driver code will read device tree node information,
and set default values if there is no info provided.
This is not done in non-OF devices leading to SGMII fifo depths being
set to the smallest size.
This patch sets the value to the default value of the PHY as stated in the
PHY datasheet.
Fixes: 4dc08dcc9f6f ("net: phy: dp83867: introduce critical chip default init for non-of platform") Signed-off-by: Michael Sit Wei Hong <michael.wei.hong.sit@intel.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20221110054938.925347-1-michael.wei.hong.sit@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Yuan Can [Thu, 10 Nov 2022 02:16:42 +0000 (02:16 +0000)]
net: hinic: Fix error handling in hinic_module_init()
A problem about hinic create debugfs failed is triggered with the
following log given:
[ 931.419023] debugfs: Directory 'hinic' with parent '/' already present!
The reason is that hinic_module_init() returns pci_register_driver()
directly without checking its return value, if pci_register_driver()
failed, it returns without destroy the newly created debugfs, resulting
the debugfs of hinic can never be created later.
Fix by removing debugfs when pci_register_driver() returns error.
Fixes: 253ac3a97921 ("hinic: add support to query sq info") Signed-off-by: Yuan Can <yuancan@huawei.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Link: https://lore.kernel.org/r/20221110021642.80378-1-yuancan@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Yang Yingliang [Wed, 9 Nov 2022 13:28:32 +0000 (21:28 +0800)]
mISDN: fix possible memory leak in mISDN_dsp_element_register()
Afer commit 1fa5ae857bb1 ("driver core: get rid of struct device's
bus_id string array"), the name of device is allocated dynamically,
use put_device() to give up the reference, so that the name can be
freed in kobject_cleanup() when the refcount is 0.
The 'entry' is going to be freed in mISDN_dsp_dev_release(), so the
kfree() is removed. list_del() is called in mISDN_dsp_dev_release(),
so it need be initialized.
Wei Yongjun [Wed, 9 Nov 2022 15:01:36 +0000 (15:01 +0000)]
net: bgmac: Drop free_netdev() from bgmac_enet_remove()
netdev is allocated in bgmac_alloc() with devm_alloc_etherdev() and will
be auto released in ->remove and ->probe failure path. Using free_netdev()
in bgmac_enet_remove() leads to double free.
We've added 11 non-merge commits during the last 8 day(s) which contain
a total of 11 files changed, 83 insertions(+), 74 deletions(-).
The main changes are:
1) Fix strncpy_from_kernel_nofault() to prevent out-of-bounds writes,
from Alban Crequy.
2) Fix for bpf_prog_test_run_skb() to prevent wrong alignment,
from Baisong Zhong.
3) Switch BPF_DISPATCHER to static_call() instead of ftrace infra, with
a small build fix on top, from Peter Zijlstra and Nathan Chancellor.
4) Fix memory leak in BPF verifier in some error cases, from Wang Yufen.
5) 32-bit compilation error fixes for BPF selftests, from Pu Lehui and
Yang Jihong.
6) Ensure even distribution of per-CPU free list elements, from Xu Kuohai.
7) Fix copy_map_value() to track special zeroed out areas properly,
from Xu Kuohai.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
bpf: Fix offset calculation error in __copy_map_value and zero_map_value
bpf: Initialize same number of free nodes for each pcpu_freelist
selftests: bpf: Add a test when bpf_probe_read_kernel_str() returns EFAULT
maccess: Fix writing offset in case of fault in strncpy_from_kernel_nofault()
selftests/bpf: Fix test_progs compilation failure in 32-bit arch
selftests/bpf: Fix casting error when cross-compiling test_verifier for 32-bit platforms
bpf: Fix memory leaks in __check_func_call
bpf: Add explicit cast to 'void *' for __BPF_DISPATCHER_UPDATE()
bpf: Convert BPF_DISPATCHER to use static_call() (not ftrace)
bpf: Revert ("Fix dispatcher patchable function entry to 5 bytes nop")
bpf, test_run: Fix alignment problem in bpf_prog_test_run_skb()
====================
Linus Torvalds [Sat, 12 Nov 2022 01:18:42 +0000 (17:18 -0800)]
Merge tag 'mm-hotfixes-stable-2022-11-11' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc hotfixes from Andrew Morton:
"22 hotfixes.
Eight are cc:stable and the remainder address issues which were
introduced post-6.0 or which aren't considered serious enough to
justify a -stable backport"
* tag 'mm-hotfixes-stable-2022-11-11' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (22 commits)
docs: kmsan: fix formatting of "Example report"
mm/damon/dbgfs: check if rm_contexts input is for a real context
maple_tree: don't set a new maximum on the node when not reusing nodes
maple_tree: fix depth tracking in maple_state
arch/x86/mm/hugetlbpage.c: pud_huge() returns 0 when using 2-level paging
fs: fix leaked psi pressure state
nilfs2: fix use-after-free bug of ns_writer on remount
x86/traps: avoid KMSAN bugs originating from handle_bug()
kmsan: make sure PREEMPT_RT is off
Kconfig.debug: ensure early check for KMSAN in CONFIG_KMSAN_WARN
x86/uaccess: instrument copy_from_user_nmi()
kmsan: core: kmsan_in_runtime() should return true in NMI context
mm: hugetlb_vmemmap: include missing linux/moduleparam.h
mm/shmem: use page_mapping() to detect page cache for uffd continue
mm/memremap.c: map FS_DAX device memory as decrypted
Partly revert "mm/thp: carry over dirty bit when thp splits on pmd"
nilfs2: fix deadlock in nilfs_count_free_blocks()
mm/mmap: fix memory leak in mmap_region()
hugetlbfs: don't delete error page from pagecache
maple_tree: reorganize testing to restore module testing
...
Linus Torvalds [Sat, 12 Nov 2022 01:10:13 +0000 (17:10 -0800)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- Another fix for rodata=full. Since rodata= is not a simple boolean on
arm64 (accepting 'full' as well), it got inadvertently broken by
changes in the core code. If rodata=on is the default and rodata=off
is passed on the kernel command line, rodata_full is never disabled
- Fix gcc compiler warning of shifting 0xc0 into bits 31:24 without an
explicit conversion to u32 (triggered by the AMPERE1 MIDR definition)
- Include asm/ptrace.h in asm/syscall_wrapper.h to fix an incomplete
struct pt_regs type causing the BPF verifier to refuse to load a
tracing program which accesses pt_regs
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64/syscall: Include asm/ptrace.h in syscall_wrapper header.
arm64: Fix bit-shifting UB in the MIDR_CPU_MODEL() macro
arm64: fix rodata=full again
Niklas Cassel [Tue, 8 Nov 2022 23:15:34 +0000 (00:15 +0100)]
ata: libata-core: do not issue non-internal commands once EH is pending
While the ATA specification states that a device should return command
aborted for all commands queued after the device has entered error state,
since ATA only keeps the sense data for the latest command (in non-NCQ
case), we really don't want to send block layer commands to the device
after it has entered error state. (Only ATA EH commands should be sent,
to read the sense data etc.)
Currently, scsi_queue_rq() will check if scsi_host_in_recovery()
(state is SHOST_RECOVERY), and if so, it will _not_ issue a command via:
scsi_dispatch_cmd() -> host->hostt->queuecommand() (ata_scsi_queuecmd())
-> __ata_scsi_queuecmd() -> ata_scsi_translate() -> ata_qc_issue()
Before commit e494f6a72839 ("[SCSI] improved eh timeout handler"),
when receiving a TFES error IRQ, the call chain looked like this:
ahci_error_intr() -> ata_port_abort() -> ata_do_link_abort() ->
ata_qc_complete() -> ata_qc_schedule_eh() -> blk_abort_request() ->
blk_rq_timed_out() -> q->rq_timed_out_fn() (scsi_times_out()) ->
scsi_eh_scmd_add() -> scsi_host_set_state(shost, SHOST_RECOVERY)
Which meant that as soon as an error IRQ was serviced, SHOST_RECOVERY
would be set.
However, after commit e494f6a72839 ("[SCSI] improved eh timeout handler"),
scsi_times_out() will instead call scsi_abort_command() which will queue
delayed work, and the worker function scmd_eh_abort_handler() will call
scsi_eh_scmd_add(), which calls scsi_host_set_state(shost, SHOST_RECOVERY).
So now, after the TFES error IRQ has been serviced, we need to wait for
the SCSI workqueue to run its work before SHOST_RECOVERY gets set.
It is worth noting that, even before commit e494f6a72839 ("[SCSI] improved
eh timeout handler"), we could receive an error IRQ from the time when
scsi_queue_rq() checks scsi_host_in_recovery(), to the time when
ata_scsi_queuecmd() is actually called.
In order to handle both the delayed setting of SHOST_RECOVERY and the
window where we can receive an error IRQ, add a check against
ATA_PFLAG_EH_PENDING (which gets set when servicing the error IRQ),
inside ata_scsi_queuecmd() itself, while holding the ap->lock.
(Since the ap->lock is held while servicing IRQs.)
Fixes: e494f6a72839 ("[SCSI] improved eh timeout handler") Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com> Tested-by: John Garry <john.g.garry@oracle.com> Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Linus Torvalds [Fri, 11 Nov 2022 22:02:44 +0000 (14:02 -0800)]
Merge tag 'io_uring-6.1-2022-11-11' of git://git.kernel.dk/linux
Pull io_uring fixes from Jens Axboe:
"Nothing major, just a few minor tweaks:
- Tweak for the TCP zero-copy io_uring self test (Pavel)
- Rather than use our internal cached value of number of CQ events
available, use what the user can see (Dylan)
- Fix a typo in a comment, added in this release (me)
- Don't allow wrapping while adding provided buffers (me)
- Fix a double poll race, and add a lockdep assertion for it too
(Pavel)"
* tag 'io_uring-6.1-2022-11-11' of git://git.kernel.dk/linux:
io_uring/poll: lockdep annote io_poll_req_insert_locked
io_uring/poll: fix double poll req->flags races
io_uring: check for rollover of buffer ID when providing buffers
io_uring: calculate CQEs from the user visible value
io_uring: fix typo in io_uring.h comment
selftests/net: don't tests batched TCP io_uring zc
projects / mirror_ubuntu-kernels.git / log