Paolo Abeni [Fri, 9 Apr 2021 11:04:37 +0000 (13:04 +0200)]
veth: use skb_orphan_partial instead of skb_orphan
As described by commit 9c4c325252c5 ("skbuff: preserve sock
reference when scrubbing the skb."), orphaning a skb
in the TX path will cause OoO.
Let's use skb_orphan_partial() instead of skb_orphan(), so
that we keep the sk around for queue's selection sake and we
still avoid the problem fixed with commit 4bf9ffa0fb57 ("veth:
Orphan skb before GRO")
Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 11 Apr 2021 23:34:56 +0000 (16:34 -0700)]
Merge branch 'ethtool-eeprom'
Moshe Shemesh says:
====================
ethtool: Extend module EEPROM dump API
Ethtool supports module EEPROM dumps via the `ethtool -m <dev>` command.
But in current state its functionality is limited - offset and length
parameters, which are used to specify a linear desired region of EEPROM
data to dump, is not enough, considering emergence of complex module
EEPROM layouts such as CMIS 4.0.
Moreover, CMIS 4.0 extends the amount of pages that may be accessible by
introducing another parameter for page addressing - banks.
Besides, currently module EEPROM is represented as a chunk of
concatenated pages, where lower 128 bytes of all pages, except page 00h,
are omitted. Offset and length are used to address parts of this fake
linear memory. But in practice drivers, which implement
get_module_info() and get_module_eeprom() ethtool ops still calculate
page number and set I2C address on their own.
This series tackles these issues by adding ethtool op, which allows to
pass page number, bank number and I2C address in addition to offset and
length parameters to the driver, adds corresponding netlink
infrastructure and implements the new interface in mlx5 driver.
This allows to extend userspace 'ethtool -m' CLI by adding new
parameters - page, bank and i2c. New command line format:
ethtool -m <dev> [hex on|off] [raw on|off] [offset N] [length N] [page N] [bank N] [i2c N]
The consequence of this series is a possibility to dump arbitrary EEPROM
page at a time, in contrast to dumps of concatenated pages. Therefore,
offset and length change their semantics and may be used only to specify
a part of data within half page boundary, which size is currently limited
to 128 bytes.
As for drivers that support legacy get_module_info() and
get_module_eeprom() pair, the series addresses it by implementing a
fallback mechanism. As mentioned earlier, such drivers derive a page
number from 'global' offset, so this can be done vice versa without
their involvement thanks to standardization. If kernel netlink handler
of 'ethtool -m' command detects that new ethtool op is not supported by
the driver, it calculates offset from given page number and page offset
and calls old ndos, if they are available.
====================
\Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Fri, 9 Apr 2021 08:06:41 +0000 (11:06 +0300)]
ethtool: wire in generic SFP module access
If the device has a sfp bus attached, call its
sfp_get_module_eeprom_by_page() function, otherwise use the ethtool op
for the device. This follows how the IOCTL works.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Fri, 9 Apr 2021 08:06:40 +0000 (11:06 +0300)]
phy: sfp: add netlink SFP support to generic SFP code
The new netlink API for reading SFP data requires a new op to be
implemented. The idea of the new netlink SFP code is that userspace is
responsible to parsing the EEPROM data and requesting pages, rather
than have the kernel decide what pages are interesting and returning
them. This allows greater flexibility for newer formats.
Currently the generic SFP code only supports simple SFPs. Allow i2c
address 0x50 and 0x51 to be accessed with page and bank must always be
0. This interface will later be extended when for example QSFP support
is added.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Vladyslav Tarasiuk <vladyslavt@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
ethtool: Add fallback to get_module_eeprom from netlink command
In case netlink get_module_eeprom_by_page() callback is not implemented
by the driver, try to call old get_module_info() and get_module_eeprom()
pair. Recalculate parameters to get_module_eeprom() offset and len using
page number and their sizes. Return error if this can't be done.
Signed-off-by: Vladyslav Tarasiuk <vladyslavt@nvidia.com> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Fri, 9 Apr 2021 08:06:38 +0000 (11:06 +0300)]
net: ethtool: Export helpers for getting EEPROM info
There are two ways to retrieve information from SFP EEPROMs. Many
devices make use of the common code, and assign the sfp_bus pointer in
the netdev to point to the bus holding the SFP device. Some MAC
drivers directly implement ops in there ethool structure.
Export within net/ethtool the two helpers used to call these methods,
so that they can also be used in the new netlink code.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
ethtool: Allow network drivers to dump arbitrary EEPROM data
Define get_module_eeprom_by_page() ethtool callback and implement
netlink infrastructure.
get_module_eeprom_by_page() allows network drivers to dump a part of
module's EEPROM specified by page and bank numbers along with offset and
length. It is effectively a netlink replacement for get_module_info()
and get_module_eeprom() pair, which is needed due to emergence of
complex non-linear EEPROM layouts.
Signed-off-by: Vladyslav Tarasiuk <vladyslavt@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Sat, 10 Apr 2021 03:57:28 +0000 (20:57 -0700)]
Merge branch 'net-ipa-a-few-small-fixes'
Alex Elder says:
====================
net: ipa: a few small fixes
This series implements some minor bug fixes or improvements.
The first patch removes an apparently unnecessary restriction, which
results in an error on a 32-bit ARM build.
The second makes a definition used for SDM845 match what is used in
the downstream code.
The third just ensures two netdev pointers are only non-null when
valid.
The fourth simplifies a little code, knowing that a called function
never returns an error.
The fifth and sixth just remove some empty/place holder functions.
And the last patch fixes a comment, makes a function private, and
removes an unnecessary double-negation of a Boolean variable. This
patch produces a warning from checkpatch, indicating that a pair of
parentheses is unnecessary. I agree with that advice, but it
conflicts with a suggestion from the compiler. I left the "problem"
in place to avoid the compiler warning.
====================
Alex Elder [Fri, 9 Apr 2021 18:07:21 +0000 (13:07 -0500)]
net: ipa: get rid of empty GSI functions
There are place holder functions in the GSI code that do nothing.
Remove these, knowing we can add something back in their place if
they're really needed someday.
Some of these are inverse functions (such as teardown to match setup).
Explicitly comment that there is no inverse in these cases.
Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alex Elder [Fri, 9 Apr 2021 18:07:20 +0000 (13:07 -0500)]
net: ipa: get rid of empty IPA functions
There are place holder functions in the IPA code that do nothing.
For the most part these are inverse functions, for example, once the
routing or filter tables are set up there is no need to perform any
matching teardown activity at shutdown, or in the case of an error.
These can be safely removed, resulting in some code simplification.
Add comments in these spots making it explicit that there is no
inverse.
Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alex Elder [Fri, 9 Apr 2021 18:07:19 +0000 (13:07 -0500)]
net: ipa: ipa_stop() does not return an error
In ipa_modem_stop(), if the modem netdev pointer is non-null we call
ipa_stop(). We check for an error and if one is returned we handle
it. But ipa_stop() never returns an error, so this extra handling
is unnecessary. Simplify the code in ipa_modem_stop() based on the
knowledge no error handling is needed at this spot.
Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alex Elder [Fri, 9 Apr 2021 18:07:18 +0000 (13:07 -0500)]
net: ipa: only set endpoint netdev pointer when in use
In ipa_modem_start(), we set endpoint netdev pointers before the
network device is registered. If registration fails, we don't undo
those assignments. Instead, wait to assign the netdev pointer until
after registration succeeds.
Set these endpoint netdev pointers to NULL in ipa_modem_stop()
before unregistering the network device.
Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alex Elder [Fri, 9 Apr 2021 18:07:17 +0000 (13:07 -0500)]
net: ipa: update sequence type for modem TX endpoint
On IPA v3.5.1, the sequencer type for the modem TX endpoint does not
define the replication portion in the same way the downstream code
does. This difference doesn't affect the behavior of the upstream
code, but I'd prefer the two code bases use the same configuration
value here.
Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alex Elder [Fri, 9 Apr 2021 18:07:16 +0000 (13:07 -0500)]
net: ipa: relax pool entry size requirement
I no longer know why a validation check ensured the size of an entry
passed to gsi_trans_pool_init() was restricted to be a multiple of 8.
For 32-bit builds, this condition doesn't always hold, and for DMA
pools, the size is rounded up to a power of 2 anyway.
Remove this restriction.
Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
MAINTAINERS
- keep Chandrasekar
drivers/net/ethernet/mellanox/mlx5/core/en_main.c
- simple fix + trust the code re-added to param.c in -next is fine
include/linux/bpf.h
- trivial
include/linux/ethtool.h
- trivial, fix kdoc while at it
include/linux/skmsg.h
- move to relevant place in tcp.c, comment re-wrapped
net/core/skmsg.c
- add the sk = sk // sk = NULL around calls
net/tipc/crypto.c
- trivial
enetc: Use generic rule to map Tx rings to interrupt vectors
Even if the current mapping is correct for the 1 CPU and 2 CPU cases
(currently enetc is included in SoCs with up to 2 CPUs only), better
use a generic rule for the mapping to cover all possible cases.
The number of CPUs is the same as the number of interrupt vectors:
Per device Tx rings -
device_tx_ring[idx], where idx = 0..n_rings_total-1
Per interrupt vector Tx rings -
int_vector[i].ring[j], where i = 0..n_int_vects-1
j = 0..n_rings_per_v-1
Mapping rule -
n_rings_per_v = n_rings_total / n_int_vects
for i = 0..n_int_vects - 1:
for j = 0..n_rings_per_v - 1:
idx = n_int_vects * j + i
int_vector[i].ring[j] <- device_tx_ring[idx]
Vladimir Oltean [Fri, 9 Apr 2021 19:27:59 +0000 (22:27 +0300)]
net: enetc: fix TX ring interrupt storm
The blamed commit introduced a bit in the TX software buffer descriptor
structure for determining whether a BD is final or not; we rearm the TX
interrupt vector for every frame (hence final BD) transmitted.
But there is a problem with the patch: it replaced a condition whose
expression is a bool which was evaluated at the beginning of the "while"
loop with a bool expression that is evaluated on the spot: tx_swbd->is_eof.
The problem with the latter expression is that the tx_swbd has already
been incremented at that stage, so the tx_swbd->is_eof check is in fact
with the _next_ software BD. Which is _not_ final.
The effect is that the CPU is in 100% load with ksoftirqd because it
does not acknowledge the TX interrupt, so the handler keeps getting
called again and again.
The fix is to restore the code structure, and keep the local bool is_eof
variable, just to assign it the tx_swbd->is_eof value instead of
!!tx_swbd->skb.
Fixes: d504498d2eb3 ("net: enetc: add a dedicated is_eof bit in the TX software BD") Reported-by: Alex Marginean <alexandru.marginean@nxp.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com> Link: https://lore.kernel.org/r/20210409192759.3895104-1-olteanv@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Sat, 10 Apr 2021 01:07:20 +0000 (18:07 -0700)]
Merge branch 'mlx5-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
Saeed Mahameed says:
====================
mlx5-next 2021-04-09
This pr contains changes from mlx5-next branch,
already reviewed on netdev and rdma mailing lists, links below.
1) From Leon, Dynamically assign MSI-X vectors count
Already Acked by Bjorn Helgaas.
https://patchwork.kernel.org/project/netdevbpf/cover/20210314124256.70253-1-leon@kernel.org/
From Mark, E-Switch cleanups and refactoring, and the addition
of single FDB mode needed HW bits.
From Mikhael, Remove unused struct field
From Saeed, Cleanup W=1 prototype warning
From Zheng, Esw related cleanup
From Tariq, User order-0 page allocation for EQs
* 'mlx5-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux:
net/mlx5: Implement sriov_get_vf_total_msix/count() callbacks
net/mlx5: Dynamically assign MSI-X vectors count
net/mlx5: Add dynamic MSI-X capabilities bits
PCI/IOV: Add sysfs MSI-X vector assignment interface
net/mlx5: Use order-0 allocations for EQs
net/mlx5: Add IFC bits needed for single FDB mode
net/mlx5: E-Switch, Refactor send to vport to be more generic
RDMA/mlx5: Use representor E-Switch when getting netdev and metadata
net/mlx5: E-Switch, Add eswitch pointer to each representor
net/mlx5: E-Switch, Add match on vhca id to default send rules
net/mlx5: Remove unused mlx5_core_health member recover_work
net/mlx5: simplify the return expression of mlx5_esw_offloads_pair()
net/mlx5: Cleanup prototype warning
====================
Qiheng Lin [Fri, 9 Apr 2021 11:53:39 +0000 (19:53 +0800)]
cxgb4: remove unneeded if-null-free check
Eliminate the following coccicheck warning:
drivers/net/ethernet/chelsio/cxgb4/cxgb4_tc_u32.c:529:3-9: WARNING:
NULL check before some freeing functions is not needed.
drivers/net/ethernet/chelsio/cxgb4/cxgb4_tc_u32.c:533:2-8: WARNING:
NULL check before some freeing functions is not needed.
drivers/net/ethernet/chelsio/cxgb4/cxgb4_cudbg.c:161:2-7: WARNING:
NULL check before some freeing functions is not needed.
drivers/net/ethernet/chelsio/cxgb4/clip_tbl.c:327:3-9: WARNING:
NULL check before some freeing functions is not needed.
====================
net: make PHY PM ops a no-op if MAC driver manages PHY PM
Resume callback of the PHY driver is called after the one for the MAC
driver. The PHY driver resume callback calls phy_init_hw(), and this is
potentially problematic if the MAC driver calls phy_start() in its resume
callback. One issue was reported with the fec driver and a KSZ8081 PHY
which seems to become unstable if a soft reset is triggered during aneg.
The new flag allows MAC drivers to indicate that they take care of
suspending/resuming the PHY. Then the MAC PM callbacks can handle
any dependency between MAC and PHY PM.
====================
net: phy: make PHY PM ops a no-op if MAC driver manages PHY PM
Resume callback of the PHY driver is called after the one for the MAC
driver. The PHY driver resume callback calls phy_init_hw(), and this is
potentially problematic if the MAC driver calls phy_start() in its resume
callback. One issue was reported with the fec driver and a KSZ8081 PHY
which seems to become unstable if a soft reset is triggered during aneg.
The new flag allows MAC drivers to indicate that they take care of
suspending/resuming the PHY. Then the MAC PM callbacks can handle
any dependency between MAC and PHY PM.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Merge tag 'io_uring-5.12-2021-04-09' of git://git.kernel.dk/linux-block
Pull io_uring fixes from Jens Axboe:
"Two minor fixups for the reissue logic, and one for making sure that
unbounded work is canceled on io-wq exit"
* tag 'io_uring-5.12-2021-04-09' of git://git.kernel.dk/linux-block:
io-wq: cancel unbounded works on io-wq destroy
io_uring: fix rw req completion
io_uring: clear F_REISSUE right after getting it
Merge tag 'devicetree-fixes-for-5.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree fixes from Rob Herring:
- Fix fw_devlink failure with ".*,nr-gpios" properties
- Doc link reference fixes from Mauro
- Fixes for unaligned FDT handling found on OpenRisc. First, avoid
crash with better error handling when unflattening an unaligned FDT.
Second, fix memory allocations for FDTs to ensure alignment.
* tag 'devicetree-fixes-for-5.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
of: property: fw_devlink: do not link ".*,nr-gpios"
dt-bindings:iio:adc: update motorola,cpcap-adc.yaml reference
dt-bindings: fix references for iio-bindings.txt
dt-bindings: don't use ../dir for doc references
of: unittest: overlay: ensure proper alignment of copied FDT
of: properly check for error returned by fdt_get_name()
Merge tag 'drm-fixes-2021-04-10' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Was relatively quiet this week, but still a few pulls came in, pretty
much small fixes across the board, a couple of regression fixes in the
amdgpu/radeon code, msm has a few minor fixes across the board, a
panel regression fix also.
xen:
- Fix use-after-free in xen
- minor duplicate defintion cleanup
vc4:
- Reduce fifo threshold on hvs4 to fix a fifo full error
- minor redunantant assignment cleanup
panel:
- Disable TE support for Droid4 and N950"
* tag 'drm-fixes-2021-04-10' of git://anongit.freedesktop.org/drm/drm:
drm/vc4: crtc: Reduce PV fifo threshold on hvs4
drm/vc4: plane: Remove redundant assignment
drm/amdgpu/smu7: fix CAC setting on TOPAZ
drm/radeon: Fix size overflow
drm/amdgpu: Fix size overflow
drm/i915: Fix invalid access to ACPI _DSM objects
drm/amd/display: Add missing mask for DCN3
drm/panel: panel-dsi-cm: disable TE for now
drm/msm/disp/dpu1: program 3d_merge only if block is attached
drm/msm: a6xx: fix version check for the A650 SQE microcode
drm/msm: Fix a5xx/a6xx timestamps
drm/msm: Fix removal of valid error case when checking speed_bin
drm/msm: Set drvdata to NULL when msm_drm_init() fails
drivers: gpu: drm: xen_drm_front_drm_info is declared twice
gpu/xen: Fix a use after free in xen_drm_drv_init
Paolo Abeni [Fri, 9 Apr 2021 15:24:17 +0000 (17:24 +0200)]
net: fix hangup on napi_disable for threaded napi
napi_disable() is subject to an hangup, when the threaded
mode is enabled and the napi is under heavy traffic.
If the relevant napi has been scheduled and the napi_disable()
kicks in before the next napi_threaded_wait() completes - so
that the latter quits due to the napi_disable_pending() condition,
the existing code leaves the NAPI_STATE_SCHED bit set and the
napi_disable() loop waiting for such bit will hang.
This patch addresses the issue by dropping the NAPI_STATE_DISABLE
bit test in napi_thread_wait(). The later napi_threaded_poll()
iteration will take care of clearing the NAPI_STATE_SCHED.
This also addresses a related problem reported by Jakub:
before this patch a napi_disable()/napi_enable() pair killed
the napi thread, effectively disabling the threaded mode.
On the patched kernel napi_disable() simply stops scheduling
the relevant thread.
v1 -> v2:
- let the main napi_thread_poll() loop clear the SCHED bit
The ethernet frame length is calculated incorrectly. Depending on
the value of RX_HEAD_PADDING, this may result in ethernet frames
that are too short (cut off at the end), or too long (garbage added
to the end).
Fix by calculating the ethernet frame length correctly. For added
clarity, use the ETH_FCS_LEN constant in the calculation.
Many thanks to Heiner Kallweit for suggesting this solution.
of: property: fw_devlink: do not link ".*,nr-gpios"
[<vendor>,]nr-gpios property is used by some GPIO drivers[0] to indicate
the number of GPIOs present on a system, not define a GPIO. nr-gpios is
not configured by #gpio-cells and can't be parsed along with other
"*-gpios" properties.
nr-gpios without the "<vendor>," prefix is not allowed by the DT
spec[1], so only add exception for the ",nr-gpios" suffix and let the
error message continue being printed for non-compliant implementations.
[0] nr-gpios is referenced in Documentation/devicetree/bindings/gpio:
- gpio-adnp.txt
- gpio-xgene-sb.txt
- gpio-xlp.txt
- snps,dw-apb-gpio.yaml
As documents have been renamed and moved around, their
references will break, but this will be unnoticed, as the
script which checks for it won't handle "../" references.
Dave Airlie [Fri, 9 Apr 2021 19:15:35 +0000 (05:15 +1000)]
Merge tag 'drm-misc-fixes-2021-04-09' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
drm-misc-fixes for v5.12-rc7:
- Fix use-after-free in xen.
- Reduce fifo threshold on hvs4 to fix a fifo full error.
- Disable TE support for Droid4 and N950.
- Small compiler fixes.
Merge tag 'selinux-pr-20210409' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux
Pull selinux fixes from Paul Moore:
"Three SELinux fixes.
These fix known problems relating to (re)loading SELinux policy or
changing the policy booleans, and pass our test suite without problem"
* tag 'selinux-pr-20210409' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux:
selinux: fix race between old and new sidtab
selinux: fix cond_list corruption when changing booleans
selinux: make nslot handling in avtab more robust
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull vdpa/mlx5 fixes from Michael Tsirkin:
"Last minute fixes.
These all look like something we are better off having
than not ..."
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
vdpa/mlx5: Fix suspend/resume index restoration
vdpa/mlx5: Fix wrong use of bit numbers
vdpa/mlx5: Retrieve BAR address suitable any function
vdpa/mlx5: Use the correct dma device when registering memory
vdpa/mlx5: should exclude header length and fcs from mtu
Merge tag 'rproc-v5.12-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/andersson/remoteproc
Pull remoteproc fixes from Bjorn Andersson:
"This fixes an issue with firmware loading on the TI K3 PRU, fixes
compatibility with GNU binutils for the same and resolves link error
due to a 64-bit division in the Qualcomm PIL info.
It also recognizes Mathieu Poirier as co-maintainer of the remoteproc
and rpmsg subsystems"
* tag 'rproc-v5.12-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/andersson/remoteproc:
remoteproc: pru: Fix firmware loading crashes on K3 SoCs
remoteproc: pru: Fix loading of GNU Binutils ELF
MAINTAINERS: Add co-maintainer for remoteproc/RPMSG subsystems
remoteproc: qcom: pil_info: avoid 64-bit division
Merge tag 'for-linus-5.12b-rc7-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fix from Juergen Gross:
"A single fix of a 5.12 patch for the rather uncommon problem of
running as a Xen guest with a real time kernel config"
* tag 'for-linus-5.12b-rc7-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/evtchn: Change irq_info lock to raw_spinlock_t
Eli Cohen [Thu, 8 Apr 2021 09:10:47 +0000 (12:10 +0300)]
vdpa/mlx5: Fix suspend/resume index restoration
When we suspend the VM, the VDPA interface will be reset. When the VM is
resumed again, clear_virtqueues() will clear the available and used
indices resulting in hardware virqtqueue objects becoming out of sync.
We can avoid this function alltogether since qemu will clear them if
required, e.g. when the VM went through a reboot.
Moreover, since the hw available and used indices should always be
identical on query and should be restored to the same value same value
for virtqueues that complete in order, we set the single value provided
by set_vq_state(). In get_vq_state() we return the value of hardware
used index.
Fixes: b35ccebe3ef7 ("vdpa/mlx5: Restore the hardware used index after change map") Fixes: 1a86b377aa21 ("vdpa/mlx5: Add VDPA driver for supported mlx5 devices") Signed-off-by: Eli Cohen <elic@nvidia.com> Link: https://lore.kernel.org/r/20210408091047.4269-6-elic@nvidia.com Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com>
Eli Cohen [Thu, 8 Apr 2021 09:10:46 +0000 (12:10 +0300)]
vdpa/mlx5: Fix wrong use of bit numbers
VIRTIO_F_VERSION_1 is a bit number. Use BIT_ULL() with mask
conditionals.
Also, in mlx5_vdpa_is_little_endian() use BIT_ULL for consistency with
the rest of the code.
Fixes: 1a86b377aa21 ("vdpa/mlx5: Add VDPA driver for supported mlx5 devices") Signed-off-by: Eli Cohen <elic@nvidia.com> Link: https://lore.kernel.org/r/20210408091047.4269-5-elic@nvidia.com Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com>
Eli Cohen [Thu, 8 Apr 2021 09:10:45 +0000 (12:10 +0300)]
vdpa/mlx5: Retrieve BAR address suitable any function
struct mlx5_core_dev has a bar_addr field that contains the correct bar
address for the function regardless of whether it is pci function or sub
function. Use it.
Fixes: 1958fc2f0712 ("net/mlx5: SF, Add auxiliary device driver") Signed-off-by: Eli Cohen <elic@nvidia.com> Reviewed-by: Parav Pandit <parav@nvidia.com> Link: https://lore.kernel.org/r/20210408091047.4269-4-elic@nvidia.com Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com>
Si-Wei Liu [Thu, 8 Apr 2021 09:10:43 +0000 (12:10 +0300)]
vdpa/mlx5: should exclude header length and fcs from mtu
When feature VIRTIO_NET_F_MTU is negotiated on mlx5_vdpa,
22 extra bytes worth of MTU length is shown in guest.
This is because the mlx5_query_port_max_mtu API returns
the "hardware" MTU value, which does not just contain the
Ethernet payload, but includes extra lengths starting
from the Ethernet header up to the FCS altogether.
Fix the MTU so packets won't get dropped silently.
Fixes: 1a86b377aa21 ("vdpa/mlx5: Add VDPA driver for supported mlx5 devices") Signed-off-by: Si-Wei Liu <si-wei.liu@oracle.com> Acked-by: Jason Wang <jasowang@redhat.com> Acked-by: Eli Cohen <elic@nvidia.com> Link: https://lore.kernel.org/r/20210408091047.4269-2-elic@nvidia.com Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Hans de Goede [Fri, 9 Apr 2021 13:58:50 +0000 (15:58 +0200)]
Bluetooth: btusb: Revert Fix the autosuspend enable and disable
drivers/usb/core/hub.c: usb_new_device() contains the following:
/* By default, forbid autosuspend for all devices. It will be
* allowed for hubs during binding.
*/
usb_disable_autosuspend(udev);
So for anything which is not a hub, such as btusb devices, autosuspend is
disabled by default and we must call usb_enable_autosuspend(udev) to
enable it.
This means that the "Fix the autosuspend enable and disable" commit,
which drops the usb_enable_autosuspend() call when the enable_autosuspend
module option is true, is completely wrong, revert it.
Merge tag '5.12-rc6-smb3' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"Three cifs/smb3 fixes, two for stable: a reconnect fix and a fix for
display of devnames with special characters"
* tag '5.12-rc6-smb3' of git://git.samba.org/sfrench/cifs-2.6:
cifs: escape spaces in share names
fs: cifs: Remove unnecessary struct declaration
cifs: On cifs_reconnect, resolve the hostname again.
net: ipv6: check for validity before dereferencing cfg->fc_nlinfo.nlh
nlh is being checked for validtity two times when it is dereferenced in
this function. Check for validity again when updating the flags through
nlh pointer to make the dereferencing safe.
CC: <stable@vger.kernel.org>
Addresses-Coverity: ("NULL pointer dereference") Signed-off-by: Muhammad Usama Anjum <musamaanjum@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 8 Apr 2021 23:38:23 +0000 (16:38 -0700)]
Merge branch 'lantiq-GSWIP-fixes'
Martin Blumenstingl says:
====================
lantiq: GSWIP: two more fixes
after my last patch got accepted and is now in net as commit 3e6fdeb28f4c33 ("net: dsa: lantiq_gswip: Let GSWIP automatically set
the xMII clock") [0] some more people from the OpenWrt community
(many thanks to everyone involved) helped test the GSWIP driver: [1]
It turns out that the previous fix does not work for all boards.
There's no regression, but it doesn't fix as many problems as I
thought. This is why two more fixes are needed:
- the first one solves many (four known but probably there are
a few extra hidden ones) reported bugs with the GSWIP where no
traffic would flow. Not all circumstances are fully understood
but testing shows that switching away from PHY auto polling
solves all of them
- while investigating the different problems which are addressed
by the first patch some small issues with the existing code were
found. These are addressed by the second patch
Changes since v1 at [0]:
- Don't configure the link parameters in gswip_phylink_mac_config
(as we're using the "modern" way in gswip_phylink_mac_link_up).
Thanks to Andrew for the hint with the phylink documentation.
- Clarify that GSWIP_MII_CFG_RMII_CLK is ignored by the hardware in
the description of the second patch as suggested by Hauke
- Don't set GSWIP_MII_CFG_RGMII_IBS in the second patch as we don't
have any hardware available for testing this. The patch
description now also reflects this.
- Added Andrew's Reviewed-by to the first patch (thank you!)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
net: dsa: lantiq_gswip: Configure all remaining GSWIP_MII_CFG bits
There are a few more bits in the GSWIP_MII_CFG register for which we
did rely on the boot-loader (or the hardware defaults) to set them up
properly.
For some external RMII PHYs we need to select the GSWIP_MII_CFG_RMII_CLK
bit and also we should un-set it for non-RMII PHYs. The
GSWIP_MII_CFG_RMII_CLK bit is ignored for other PHY connection modes.
The GSWIP IP also supports in-band auto-negotiation for RGMII PHYs when
the GSWIP_MII_CFG_RGMII_IBS bit is set. Clear this bit always as there's
no known hardware which uses this (so it is not tested yet).
Clear the xMII isolation bit when set at initialization time if it was
previously set by the bootloader. Not doing so could lead to no traffic
(neither RX nor TX) on a port with this bit set.
While here, also add the GSWIP_MII_CFG_RESET bit. We don't need to
manage it because this bit is self-clearning when set. We still add it
here to get a better overview of the GSWIP_MII_CFG register.
Fixes: 14fceff4771e51 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200") Cc: stable@vger.kernel.org Suggested-by: Hauke Mehrtens <hauke@hauke-m.de> Acked-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: dsa: lantiq_gswip: Don't use PHY auto polling
PHY auto polling on the GSWIP hardware can be used so link changes
(speed, link up/down, etc.) can be detected automatically. Internally
GSWIP reads the PHY's registers for this functionality. Based on this
automatic detection GSWIP can also automatically re-configure it's port
settings. Unfortunately this auto polling (and configuration) mechanism
seems to cause various issues observed by different people on different
devices:
- FritzBox 7360v2: the two Gbit/s ports (connected to the two internal
PHY11G instances) are working fine but the two Fast Ethernet ports
(using an AR8030 RMII PHY) are completely dead (neither RX nor TX are
received). It turns out that the AR8030 PHY sets the BMSR_ESTATEN bit
as well as the ESTATUS_1000_TFULL and ESTATUS_1000_XFULL bits. This
makes the PHY auto polling state machine (rightfully?) think that the
established link speed (when the other side is Gbit/s capable) is
1Gbit/s.
- None of the Ethernet ports on the Zyxel P-2812HNU-F1 (two are
connected to the internal PHY11G GPHYs while the other three are
external RGMII PHYs) are working. Neither RX nor TX traffic was
observed. It is not clear which part of the PHY auto polling state-
machine caused this.
- FritzBox 7412 (only one LAN port which is connected to one of the
internal GPHYs running in PHY22F / Fast Ethernet mode) was seeing
random disconnects (link down events could be seen). Sometimes all
traffic would stop after such disconnect. It is not clear which part
of the PHY auto polling state-machine cauased this.
- TP-Link TD-W9980 (two ports are connected to the internal GPHYs
running in PHY11G / Gbit/s mode, the other two are external RGMII
PHYs) was affected by similar issues as the FritzBox 7412 just without
the "link down" events
Switch to software based configuration instead of PHY auto polling (and
letting the GSWIP hardware configure the ports automatically) for the
following link parameters:
- link up/down
- link speed
- full/half duplex
- flow control (RX / TX pause)
After a big round of manual testing by various people (who helped test
this on OpenWrt) it turns out that this fixes all reported issues.
Additionally it can be considered more future proof because any
"quirk" which is implemented for a PHY on the driver side can now be
used with the GSWIP hardware as well because Linux is in control of the
link parameters.
As a nice side-effect this also solves a problem where fixed-links were
not supported previously because we were relying on the PHY auto polling
mechanism, which cannot work for fixed-links as there's no PHY from
where it can read the registers. Configuring the link settings on the
GSWIP ports means that we now use the settings from device-tree also for
ports with fixed-links.
Fixes: 14fceff4771e51 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200") Fixes: 3e6fdeb28f4c33 ("net: dsa: lantiq_gswip: Let GSWIP automatically set the xMII clock") Cc: stable@vger.kernel.org Acked-by: Hauke Mehrtens <hauke@hauke-m.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma fixes from Jason Gunthorpe:
"Nothing very exciting here, just a few small bug fixes. No red flags
for this release have shown up.
- Regression from the last pull request in cxgb4 related to the ipv6
fixes
- KASAN crasher in rtrs
- oops in hfi1 related to a buggy BIOS
- Userspace could oops qedr's XRC support
- Uninitialized memory when parsing a LS_NLA_TYPE_DGID netlink
message"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/addr: Be strict with gid size
RDMA/qedr: Fix kernel panic when trying to access recv_cq
IB/hfi1: Fix probe time panic when AIP is enabled with a buggy BIOS
RDMA/cxgb4: check for ipv6 address properly while destroying listener
RDMA/rtrs-clt: Close rtrs client conn before destroying rtrs clt session files
Frank Rowand [Thu, 8 Apr 2021 20:45:08 +0000 (15:45 -0500)]
of: unittest: overlay: ensure proper alignment of copied FDT
The Devicetree standard specifies an 8 byte alignment of the FDT.
Code in libfdt expects this alignment for an FDT image in memory.
kmemdup() returns 4 byte alignment on openrisc. Replace kmemdup()
with kmalloc(), align pointer, memcpy() to get proper alignment.
The 4 byte alignment exposed a related bug which triggered a crash
on openrisc with:
commit 79edff12060f ("scripts/dtc: Update to upstream version v1.6.0-51-g183df9e9c2b9")
as reported in:
https://lore.kernel.org/lkml/20210327224116.69309-1-linux@roeck-us.net/
David S. Miller [Thu, 8 Apr 2021 21:19:32 +0000 (14:19 -0700)]
Merge tag 'for-net-next-2021-04-08' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
Luiz Augusto von Dentz says:
====================
bluetooth-next pull request for net-next:
- Proper support for BCM4330 and BMC4334
- Various improvements for firmware download of Intel controllers
- Update management interface revision to 20
- Support for AOSP HCI vendor commands
- Initial Virtio support
====================
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 8 Apr 2021 21:18:25 +0000 (14:18 -0700)]
Merge branch '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
100GbE Intel Wired LAN Driver Updates 2021-04-08
This series contains updates to ice driver only.
Chinh adds retrying of sending some AQ commands when receiving EBUSY
error.
Victor modifies how nodes are added to reduce stack usage.
Ani renames some variables to either follow spec naming or to be inline
with naming in the rest of the driver. Ignores EMODE error as there are
cases where this error is expected. Performs some cleanup such as
removing unnecessary checks, doing variable assignments over copies, and
removing unneeded variables. Revises some error codes returned in link
settings to be more appropriate. He also implements support for new
firmware option to get default link configuration which accounts for
any needed NVM based overrides for PHY configuration. He also removes
the rx_gro_dropped stat as the value no longer changes.
Jeb removes setting specific link modes on firmwares that no longer
require it.
Brett removes unnecessary checks when adding and removing VLANs.
Tony fixes a checkpatch warning for unnecessary blank line.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Null pointer dereference happens on master->slaves dereference in
teql_destroy() as master is null-pointer.
When qdisc_create() calls teql_qdisc_init() it imediately fails after
check "if (m->dev == dev)" because both devices are teql0, and it does
not set qdisc_priv(sch)->m leaving it zero on error path, then
qdisc_create() imediately calls teql_destroy() which does not expect
zero master pointer and we get OOPS.
Fixes: 87b60cfacf9f ("net_sched: fix error recovery at qdisc creation") Signed-off-by: Pavel Tikhomirov <ptikhomirov@virtuozzo.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 8 Apr 2021 21:08:37 +0000 (14:08 -0700)]
Merge tag 'mac80211-for-net-2021-04-08.2' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes berg says:
====================
Various small fixes:
* S1G beacon validation
* potential leak in nl80211
* fast-RX confusion with 4-addr mode
* erroneous WARN_ON that userspace can trigger
* wrong time units in virt_wifi
* rfkill userspace API breakage
* TXQ AC confusing that led to traffic stopped forever
* connection monitoring time after/before confusion
* netlink beacon head validation buffer overrun
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
ipv6: report errors for iftoken via netlink extack
Setting iftoken can fail for several different reasons but there
and there was no report to user as to the cause. Add netlink
extended errors to the processing of the request.
This requires adding additional argument through rtnl_af_ops
set_link_af callback.
Reported-by: Hongren Zheng <li@zenithal.me> Signed-off-by: Stephen Hemminger <stephen@networkplumber.org> Reviewed-by: David Ahern <dsahern@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 8 Apr 2021 20:47:34 +0000 (13:47 -0700)]
Merge branch 'net-sched-action-init-fixes'
Vlad Buslov says:
====================
Action initalization fixes
This series fixes reference counting of action instances and modules in
several parts of action init code. The first patch reverts previous fix
that didn't properly account for rollback from a failure in the middle of
the loop in tcf_action_init() which is properly fixed by the following
patch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
With recent changes that separated action module load from action
initialization tcf_action_init() function error handling code was modified
to manually release the loaded modules if loading/initialization of any
further action in same batch failed. For the case when all modules
successfully loaded and some of the actions were initialized before one of
them failed in init handler. In this case for all previous actions the
module will be released twice by the error handler: First time by the loop
that manually calls module_put() for all ops, and second time by the action
destroy code that puts the module after destroying the action.
Reproduction:
$ sudo tc actions add action simple sdata \"2\" index 2
$ sudo tc actions add action simple sdata \"1\" index 1 \
action simple sdata \"2\" index 2
RTNETLINK answers: File exists
We have an error talking to the kernel
$ sudo tc actions ls action simple
total acts 1
action order 0: Simple <"2">
index 2 ref 1 bind 0
$ sudo tc actions flush action simple
$ sudo tc actions ls action simple
$ sudo tc actions add action simple sdata \"2\" index 2
Error: Failed to load TC action module.
We have an error talking to the kernel
$ lsmod | grep simple
act_simple 20480 -1
Fix the issue by modifying module reference counting handling in action
initialization code:
- Get module reference in tcf_idr_create() and put it in tcf_idr_release()
instead of taking over the reference held by the caller.
- Modify users of tcf_action_init_1() to always release the module
reference which they obtain before calling init function instead of
assuming that created action takes over the reference.
- Finally, modify tcf_action_init_1() to not release the module reference
when overwriting existing action as this is no longer necessary since both
upper and lower layers obtain and manage their own module references
independently.
Fixes: d349f9976868 ("net_sched: fix RTNL deadlock again caused by request_module()") Suggested-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: Vlad Buslov <vladbu@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Action init code increments reference counter when it changes an action.
This is the desired behavior for cls API which needs to obtain action
reference for every classifier that points to action. However, act API just
needs to change the action and releases the reference before returning.
This sequence breaks when the requested action doesn't exist, which causes
act API init code to create new action with specified index, but action is
still released before returning and is deleted (unless it was referenced
concurrently by cls API).
Reproduction:
$ sudo tc actions ls action gact
$ sudo tc actions change action gact drop index 1
$ sudo tc actions ls action gact
Extend tcf_action_init() to accept 'init_res' array and initialize it with
action->ops->init() result. In tcf_action_add() remove pointers to created
actions from actions array before passing it to tcf_action_put_many().
Fixes: cae422f379f3 ("net: sched: use reference counting action init") Reported-by: Kumar Kartikeya Dwivedi <memxor@gmail.com> Signed-off-by: Vlad Buslov <vladbu@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tian Tao [Thu, 8 Apr 2021 07:00:41 +0000 (15:00 +0800)]
net: qed: remove unused including <linux/version.h>
Remove including <linux/version.h> that don't need it.
Signed-off-by: Tian Tao <tiantao6@hisilicon.com> Signed-off-by: Zhiqi Song <songzhiqi1@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
To implement the system suspend/resume functions, the NIC driver needs
to support:
1. When the system enters the suspend mode, the driver needs to
implement the suspend callback function of the NIC device. The driver
needs to mute the device, stop all RX/TX activities of the device, and
unmap the interrupt.
2. When the system enters the resume mode, the driver needs to
implement the resume callback function of the NIC device and restore
the device to the state before suspension.
When the system enters the suspend and resume mode, the NIC driver
actually executes the PF function reset process.
When the PFs are suspending/resuming, VFs also enter the suspend/resume
state because the PFs trigger the VFs to reset, therefore no operation
is required when the VF pci_driver is suspending or resuming.
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: hns3: change flr_prepare/flr_done function names
The flr_prepare/flr_done functions are not only used in the FLR scenario,
but also used in the suspend/resume.
Change the function names to prepare_for_reset/rebuild_for_reset, change
the flr_prepare/flr_done to reset_prepare/reset_done in hnae3_ae_ops.
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Shannon Nelson [Wed, 7 Apr 2021 23:20:00 +0000 (16:20 -0700)]
ionic: add ts_config replay
Split the call into ionic_lif_hwstamp_set() to have two
separate interfaces, one from the ioctl() for changing the
configuration and one for replaying the current configuration
after a FW RESET.
Signed-off-by: Shannon Nelson <snelson@pensando.io> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 8 Apr 2021 20:15:34 +0000 (13:15 -0700)]
Merge branch 'marvell10g-updates'
Marek Behún says:
====================
net: phy: marvell10g updates
Here are some updates for marvell10g PHY driver.
I am still working on some more changes for this driver, but I would
like to have at least something reviewed / applied.
Changes since v3:
- added Andrew's Reviewed-by tags
- removed patches adding variadic-macro library and bitmap
initialization macro - it causes warning that we are not currently
able to fix easily. Instead the supported_interfaces bitmap is now
initialized via a chip specific method
- added explanation of mactype initialization to commit message of patch
07/16
- fixed repeated word in commit message of second to last patch
Changes since v2:
- code refactored to use an additional structure mv3310_chip describing
mv3310 specific properties / operations for PHYs supported by this
driver
- added separate phy_driver structures for 88X3340 and 88E2111
- removed 88E2180 specific code (dual-port and quad-port SXGMII modes
are ignored for now)
Changes since v1:
- added various MACTYPEs support also for 88E21XX
- differentiate between specific models with same PHY_ID
- better check for compatible interface
- print exact model
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Marek Behún [Wed, 7 Apr 2021 20:22:49 +0000 (22:22 +0200)]
net: phy: marvell10g: add separate structure for 88X3340
The 88X3340 contains 4 cores similar to 88X3310, but there is a
difference: it does not support xaui host mode. Instead the
corresponding MACTYPE means
rxaui / 5gbase-r / 2500base-x / sgmii without AN
Signed-off-by: Marek Behún <kabel@kernel.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / mirror_ubuntu-kernels.git / log