Tests showed that under stress conditions the kernel may
temporary fail to allocate 256k with kmalloc. However,
this fix reworks the related code in the cca_findcard2()
function to use kvmalloc instead.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com> Reviewed-by: Ingo Franzki <ifranzki@linux.ibm.com> Cc: Stable <stable@vger.kernel.org> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
The x86-64 psABI [0] specifies special relocation types
(R_X86_64_[REX_]GOTPCRELX) for indirection through the Global Offset
Table, semantically equivalent to R_X86_64_GOTPCREL, which the linker
can take advantage of for optimization (relaxation) at link time. This
is supported by LLD and binutils versions 2.26 onwards.
The compressed kernel is position-independent code, however, when using
LLD or binutils versions before 2.27, it must be linked without the -pie
option. In this case, the linker may optimize certain instructions into
a non-position-independent form, by converting foo@GOTPCREL(%rip) to $foo.
This potential issue has been present with LLD and binutils-2.26 for a
long time, but it has never manifested itself before now:
- LLD and binutils-2.26 only relax
movq foo@GOTPCREL(%rip), %reg
to
leaq foo(%rip), %reg
which is still position-independent, rather than
mov $foo, %reg
which is permitted by the psABI when -pie is not enabled.
- GCC happens to only generate GOTPCREL relocations on mov instructions.
- CLang does generate GOTPCREL relocations on non-mov instructions, but
when building the compressed kernel, it uses its integrated assembler
(due to the redefinition of KBUILD_CFLAGS dropping -no-integrated-as),
which has so far defaulted to not generating the GOTPCRELX
relocations.
Nick Desaulniers reports [1,2]:
"A recent change [3] to a default value of configuration variable
(ENABLE_X86_RELAX_RELOCATIONS OFF -> ON) in LLVM now causes Clang's
integrated assembler to emit R_X86_64_GOTPCRELX/R_X86_64_REX_GOTPCRELX
relocations. LLD will relax instructions with these relocations based
on whether the image is being linked as position independent or not.
When not, then LLD will relax these instructions to use absolute
addressing mode (R_RELAX_GOT_PC_NOPIC). This causes kernels built with
Clang and linked with LLD to fail to boot."
Patch series [4] is a solution to allow the compressed kernel to be
linked with -pie unconditionally, but even if merged is unlikely to be
backported. As a simple solution that can be applied to stable as well,
prevent the assembler from generating the relaxed relocation types using
the -mrelax-relocations=no option. For ease of backporting, do this
unconditionally.
These serial ports are exposed by the OOB-management-engine on
RealManage-enabled network cards (e.g. AMD DASH enabled systems using
Realtek cards).
Because these have 3 BARs, they fail the "num_iomem <= 1" check in
serial_pci_guess_board.
I've manually checked the two IOMEM regions and BAR 2 doesn't seem to
respond to reads, but BAR 4 seems to be an MMIO version of the IO ports
(untested).
With this change, the ports are detected:
0000:02:00.1: ttyS0 at I/O 0x2200 (irq = 82, base_baud = 115200) is a 16550A
0000:02:00.2: ttyS1 at I/O 0x2100 (irq = 55, base_baud = 115200) is a 16550A
Variable populated, which is a member of struct pcpu_chunk, is used as a
unit of size of unsigned long.
However, size of populated is miscounted. So, I fix this minor part.
Fixes: 8ab16c43ea79 ("percpu: change the number of pages marked in the first_chunk pop bitmap") Cc: <stable@vger.kernel.org> # 4.14+ Signed-off-by: Sunghyun Jin <mcsmonk@gmail.com> Signed-off-by: Dennis Zhou <dennis@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
The Mic connects to the Nid 0x19, but the configuration of Nid 0x19
is not defined to Mic, and also need to set the coeff to enable the
auto detection on the Nid 0x19. After this change, the Mic plugging
in or plugging out could be detected and could record the sound from
the Mic.
And the coeff value is suggested by Kailang of Realtek.
Cc: Kailang Yang <kailang@realtek.com> Cc: <stable@vger.kernel.org> Signed-off-by: Hui Wang <hui.wang@canonical.com> Link: https://lore.kernel.org/r/20200909020041.8967-1-hui.wang@canonical.com Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
The GX502 requires a few steps to enable the headset i/o: pincfg,
verbs to enable and unmute the amp used for headpone out, and
a jacksense callback to toggle output via internal or jack using
a verb.
On suspend the original host configuration gets restored. The
resume routine has to undo this, otherwise the SMBus master
may be left in disabled state or in i2c mode.
[JD: Rebased on v5.8, moved the write into i801_setup_hstcfg.]
Signed-off-by: Volker Rümelin <vr_qemu@t-online.de> Signed-off-by: Jean Delvare <jdelvare@suse.de> Signed-off-by: Wolfram Sang <wsa@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
Sometimes the embedded controller firmware does not
terminate the list of alternate modes that the partner
supports in its response to the GET_ALTERNATE_MODES command.
Instead the firmware returns the supported alternate modes
over and over again until the driver stops requesting them.
If that happens, the number of modes for each alternate mode
will exceed the maximum 6 that is defined in the USB Power
Delivery specification. Making sure that can't happen by
adding a check for it.
This fixes NULL pointer dereference that is caused by the
overrun.
Fixes: ad74b8649beaf ("usb: typec: ucsi: Preliminary support for alternate modes") Cc: stable@vger.kernel.org Reported-by: Zwane Mwaikambo <zwanem@gmail.com> Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Link: https://lore.kernel.org/r/20200916090034.25119-3-heikki.krogerus@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
The SCSI layer can go into an ugly loop if you ignore that a device is
gone. You need to report an error in the command rather than in the
return value of the queue method.
We need to specifically check for ENODEV. The issue goes back to the
introduction of the driver.
Fixes: 115bb1ffa54c3 ("USB: Add UAS driver") Signed-off-by: Oliver Neukum <oneukum@suse.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200916094026.30085-2-oneukum@suse.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
Add a USB_QUIRK_IGNORE_REMOTE_WAKEUP quirk for the BYD zhaoxin notebook.
This notebook come with usb touchpad. And we would like to disable
touchpad wakeup on this notebook by default.
(NOTE: This is the minimal backportable fix, a full fix is being
developed at https://patchwork.freedesktop.org/patch/388048/)
The flags passed to the wait_entry.func are passed onwards to
try_to_wake_up(), which has a very particular interpretation for its
wake_flags. In particular, beyond the published WF_SYNC, it has a few
internal flags as well. Since we passed the fence->error down the chain
via the flags argument, these ended up in the default_wake_function
confusing the kernel/sched.
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/2110 Fixes: ef4688497512 ("drm/i915: Propagate fence errors") Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Matthew Auld <matthew.auld@intel.com> Cc: <stable@vger.kernel.org> # v5.4+ Reviewed-by: Matthew Auld <matthew.auld@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200728152144.1100-1-chris@chris-wilson.co.uk Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
[Joonas: Rebased and reordered into drm-intel-gt-next branch]
[Joonas: Added a note and link about more complete fix] Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
(cherry picked from commit f4b3c395540aa3d4f5a6275c5bdd83ab89034806) Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
The driver-specific usage of the DMA_CTRL_ACK flag was replaced with a
custom flag in commit ceeeb99cd821 ("dmaengine: mxs: rename custom flag"),
but i2c-mxs was not updated to use the new flag, completely breaking I2C
transactions using DMA.
The reason is the offset[] creation and later usage, while building
the eBPF body. The code currently omits the first instruction, since
build_insn() will increase our ctx->idx before saving it.
That was fine up until bounded eBPF loops were introduced. After that
introduction, offset[0] must be the offset of the end of prologue which
is the start of the 1st insn while, offset[n] holds the
offset of the end of n-th insn.
When "taken loop with back jump to 1st insn" test runs, it will
eventually call bpf2a64_offset(-1, 2, ctx). Since negative indexing is
permitted, the current outcome depends on the value stored in
ctx->offset[-1], which has nothing to do with our array.
If the value happens to be 0 the tests will work. If not this error
triggers.
commit 7c2e988f400e ("bpf: fix x64 JIT code generation for jmp to 1st insn")
fixed an indentical bug on x86 when eBPF bounded loops were introduced.
So let's fix it by creating the ctx->offset[] differently. Track the
beginning of instruction and account for the extra instruction while
calculating the arm instruction offsets.
if of_find_device_by_node() succeed, mtk_drm_kms_init() doesn't have
a corresponding put_device(). Thus add jump target to fix the exception
handling for this function implementation.
Fixes: 8f83f26891e1 ("drm/mediatek: Add HDMI support") Signed-off-by: Yu Kuai <yukuai3@huawei.com> Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
On A20R machines the interrupt pending bits in cause register need to be
updated by requesting the chipset to do it. This needs to be done to
find the interrupt cause and after interrupt service. In
commit 0b888c7f3a03 ("MIPS: SNI: Convert to new irq_chip functions") the
function to do after service update got lost, which caused spurious
interrupts.
Fixes: 0b888c7f3a03 ("MIPS: SNI: Convert to new irq_chip functions") Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
syzbot is reporting OOB read at fbcon_resize() [1], for
commit 39b3cffb8cf31117 ("fbcon: prevent user font height or width change
from causing potential out-of-bounds access") is by error using
registered_fb[con2fb_map[vc->vc_num]]->fbcon_par->p->userfont (which was
set to non-zero) instead of fb_display[vc->vc_num].userfont (which remains
zero for that display).
We could remove tricky userfont flag [2], for we can determine it by
comparing address of the font data and addresses of built-in font data.
But since that commit is failing to fix the original OOB read [3], this
patch keeps the change minimal in case we decide to revert altogether.
Indirect leak of 360 byte(s) in 9 object(s) allocated from:
#0 0x7fecc305180e in calloc (/lib/x86_64-linux-gnu/libasan.so.5+0x10780e)
#1 0x560578f6dce5 in perf_pmu__new_format util/pmu.c:1333
#2 0x560578f752fc in perf_pmu_parse util/pmu.y:59
#3 0x560578f6a8b7 in perf_pmu__format_parse util/pmu.c:73
#4 0x560578e07045 in test__pmu tests/pmu.c:155
#5 0x560578de109b in run_test tests/builtin-test.c:410
#6 0x560578de109b in test_and_print tests/builtin-test.c:440
#7 0x560578de401a in __cmd_test tests/builtin-test.c:661
#8 0x560578de401a in cmd_test tests/builtin-test.c:807
#9 0x560578e49354 in run_builtin /home/namhyung/project/linux/tools/perf/perf.c:312
#10 0x560578ce71a8 in handle_internal_command /home/namhyung/project/linux/tools/perf/perf.c:364
#11 0x560578ce71a8 in run_argv /home/namhyung/project/linux/tools/perf/perf.c:408
#12 0x560578ce71a8 in main /home/namhyung/project/linux/tools/perf/perf.c:538
#13 0x7fecc2b7acc9 in __libc_start_main ../csu/libc-start.c:308
Fixes: cff7f956ec4a1 ("perf tests: Move pmu tests into separate object") Signed-off-by: Namhyung Kim <namhyung@kernel.org> Acked-by: Jiri Olsa <jolsa@redhat.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: Ian Rogers <irogers@google.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Link: http://lore.kernel.org/lkml/20200915031819.386559-12-namhyung@kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
The evsel->unit borrows a pointer of pmu event or alias instead of
owns a string. But tool event (duration_time) passes a result of
strdup() caused a leak.
It was found by ASAN during metric test:
Direct leak of 210 byte(s) in 70 object(s) allocated from:
#0 0x7fe366fca0b5 in strdup (/lib/x86_64-linux-gnu/libasan.so.5+0x920b5)
#1 0x559fbbcc6ea3 in add_event_tool util/parse-events.c:414
#2 0x559fbbcc6ea3 in parse_events_add_tool util/parse-events.c:1414
#3 0x559fbbd8474d in parse_events_parse util/parse-events.y:439
#4 0x559fbbcc95da in parse_events__scanner util/parse-events.c:2096
#5 0x559fbbcc95da in __parse_events util/parse-events.c:2141
#6 0x559fbbc28555 in check_parse_id tests/pmu-events.c:406
#7 0x559fbbc28555 in check_parse_id tests/pmu-events.c:393
#8 0x559fbbc28555 in check_parse_cpu tests/pmu-events.c:415
#9 0x559fbbc28555 in test_parsing tests/pmu-events.c:498
#10 0x559fbbc0109b in run_test tests/builtin-test.c:410
#11 0x559fbbc0109b in test_and_print tests/builtin-test.c:440
#12 0x559fbbc03e69 in __cmd_test tests/builtin-test.c:695
#13 0x559fbbc03e69 in cmd_test tests/builtin-test.c:807
#14 0x559fbbc691f4 in run_builtin /home/namhyung/project/linux/tools/perf/perf.c:312
#15 0x559fbbb071a8 in handle_internal_command /home/namhyung/project/linux/tools/perf/perf.c:364
#16 0x559fbbb071a8 in run_argv /home/namhyung/project/linux/tools/perf/perf.c:408
#17 0x559fbbb071a8 in main /home/namhyung/project/linux/tools/perf/perf.c:538
#18 0x7fe366b68cc9 in __libc_start_main ../csu/libc-start.c:308
Fixes: f0fbb114e3025 ("perf stat: Implement duration_time as a proper event") Signed-off-by: Namhyung Kim <namhyung@kernel.org> Acked-by: Jiri Olsa <jolsa@redhat.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: Ian Rogers <irogers@google.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Link: http://lore.kernel.org/lkml/20200915031819.386559-6-namhyung@kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
Asan reported leak of cpu and thread maps as they have one more refcount
than released. I found that after setting evlist maps it should release
it's refcount.
It seems to be broken from the beginning so I chose the original commit
as the culprit. But not sure how it's applied to stable trees since
there are many changes in the code after that.
Fixes: 7e2ed097538c5 ("perf evlist: Store pointer to the cpu and thread maps") Fixes: 4112eb1899c0e ("perf evlist: Default to syswide target when no thread/cpu maps set") Signed-off-by: Namhyung Kim <namhyung@kernel.org> Acked-by: Jiri Olsa <jolsa@redhat.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: Ian Rogers <irogers@google.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Link: http://lore.kernel.org/lkml/20200915031819.386559-4-namhyung@kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
Commit 930beb5ac09a ("MIPS: introduce MIPS_L1_CACHE_SHIFT_<N>") forgot
to select the correct MIPS_L1_CACHE_SHIFT for SNI RM. This breaks non
coherent DMA because of a wrong allocation alignment.
Fixes: 930beb5ac09a ("MIPS: introduce MIPS_L1_CACHE_SHIFT_<N>") Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
When compiling with DEBUG=1 on Fedora 32 I'm getting crash for 'perf
test signal':
Program received signal SIGSEGV, Segmentation fault.
0x0000000000c68548 in __test_function ()
(gdb) bt
#0 0x0000000000c68548 in __test_function ()
#1 0x00000000004d62e9 in test_function () at tests/bp_signal.c:61
#2 0x00000000004d689a in test__bp_signal (test=0xa8e280 <generic_ ...
#3 0x00000000004b7d49 in run_test (test=0xa8e280 <generic_tests+1 ...
#4 0x00000000004b7e7f in test_and_print (t=0xa8e280 <generic_test ...
#5 0x00000000004b8927 in __cmd_test (argc=1, argv=0x7fffffffdce0, ...
...
It's caused by the symbol __test_function being in the ".bss" section:
$ nm perf | grep __test_function 0000000000c68548 B __test_function
I guess most of the time we're just lucky the inline asm ended up in the
".text" section, so making it specific explicit with push and pop
section clauses.
vmbus_wait_for_unload() looks for a CHANNELMSG_UNLOAD_RESPONSE message
coming from Hyper-V. But if the message isn't found for some reason,
the panic path gets hung forever. Add a timeout of 10 seconds to prevent
this.
Fixes: 415719160de3 ("Drivers: hv: vmbus: avoid scheduling in interrupt context in vmbus_initiate_unload()") Signed-off-by: Michael Kelley <mikelley@microsoft.com> Reviewed-by: Dexuan Cui <decui@microsoft.com> Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com> Link: https://lore.kernel.org/r/1600026449-23651-1-git-send-email-mikelley@microsoft.com Signed-off-by: Wei Liu <wei.liu@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
Now that we allow CPUs affected by erratum 1418040 to come in late,
this prevents their unaffected sibblings from coming in late (or
coming back after a suspend or hotplug-off, which amounts to the
same thing).
To allow this, we need to add ARM64_CPUCAP_OPTIONAL_FOR_LATE_CPU,
which amounts to set .type to ARM64_CPUCAP_WEAK_LOCAL_CPU_FEATURE.
Fixes: bf87bb0881d0 ("arm64: Allow booting of late CPUs affected by erratum 1418040") Reported-by: Matthias Kaehlcke <mka@chromium.org> Signed-off-by: Marc Zyngier <maz@kernel.org> Tested-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org> Tested-by: Matthias Kaehlcke <mka@chromium.org> Acked-by: Will Deacon <will@kernel.org> Link: https://lore.kernel.org/r/20200911181611.2073183-1-maz@kernel.org Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
In sas_notify_lldd_dev_found(), if we can't allocate the necessary
resources, then it seems like the wrong thing to mark the device as found
and to increment the reference count. None of the callers ever drop the
reference in that situation.
[mkp: tweaked commit desc based on feedback from John]
Link: https://lore.kernel.org/r/20200905125836.GF183976@mwanda Fixes: 735f7d2fedf5 ("[SCSI] libsas: fix domain_device leak") Reviewed-by: Jason Yan <yanaijie@huawei.com> Acked-by: John Garry <john.garry@huawei.com> Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
After we Stop and later Start a VM that uses Accelerated Networking (NIC
SR-IOV), currently the VF vmbus device's Instance GUID can change, so after
vmbus_bus_resume() -> vmbus_request_offers(), vmbus_onoffer() can not find
the original vmbus channel of the VF, and hence we can't complete()
vmbus_connection.ready_for_resume_event in check_ready_for_resume_event(),
and the VM hangs in vmbus_bus_resume() forever.
Fix the issue by adding a timeout, so the resuming can still succeed, and
the saved state is not lost, and according to my test, the user can disable
Accelerated Networking and then will be able to SSH into the VM for
further recovery. Also prevent the VM in question from suspending again.
The host will be fixed so in future the Instance GUID will stay the same
across hibernation.
Fixes: d8bd2d442bb2 ("Drivers: hv: vmbus: Resume after fixing up old primary channels") Signed-off-by: Dexuan Cui <decui@microsoft.com> Reviewed-by: Michael Kelley <mikelley@microsoft.com> Link: https://lore.kernel.org/r/20200905025555.45614-1-decui@microsoft.com Signed-off-by: Wei Liu <wei.liu@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
On g12 and following platforms, The first channel of record with more than
2 channels ends being placed randomly on an even channel of the output.
On these SoCs, a bit was added to force the first channel to be placed at
the beginning of the output. Apparently the behavior if the bit is not set
is not easily predictable. According to the documentation, this bit is not
present on the axg series.
Set the bit on g12 and fix the problem.
Fixes: a3c23a8ad4dc ("ASoC: meson: axg-toddr: add g12a support") Reported-by: Nicolas Belin <nbelin@baylibre.com> Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Link: https://lore.kernel.org/r/20200828151438.350974-1-jbrunet@baylibre.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
If the hypervisor doesn't support hugepages, the kernel ends up allocating a large
number of page table pages. The early page table allocation was wrongly
setting the max memblock limit to ppc64_rma_size with radix translation
which resulted in boot failure as shown below.
This was because the kernel was checking for the radix feature before we enable the
feature via mmu_features. This resulted in the kernel using hash restrictions on
radix.
Rework the early init code such that the kernel boot with memblock restrictions
as imposed by hash. At that point, the kernel still hasn't finalized the
translation the kernel will end up using.
We have three different ways of detecting radix.
1. dt_cpu_ftrs_scan -> used only in case of PowerNV
2. ibm,pa-features -> Used when we don't use cpu_dt_ftr_scan
3. CAS -> Where we negotiate with hypervisor about the supported translation.
We look at 1 or 2 early in the boot and after that, we look at the CAS vector to
finalize the translation the kernel will use. We also support a kernel command
line option (disable_radix) to switch to hash.
Update the memblock limit after mmu_early_init_devtree() if the kernel is going
to use radix translation. This forces some of the memblock allocations we do before
mmu_early_init_devtree() to be within the RMA limit.
Fixes: 2bfd65e45e87 ("powerpc/mm/radix: Add radix callbacks for early init routines") Reported-by: Shirisha Ganta <shiganta@in.ibm.com> Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com> Reviewed-by: Hari Bathini <hbathini@linux.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200828100852.426575-1-aneesh.kumar@linux.ibm.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
for_each_child_of_node returns a node pointer np with
refcount incremented. So when devm_kzalloc fails, a
pairing refcount decrement is needed to keep np's
refcount balanced.
Fixes: 16395ceee11f8 ("ASoC: qcom: common: Fix NULL pointer in of parser") Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn> Link: https://lore.kernel.org/r/20200820042828.10308-1-dinghao.liu@zju.edu.cn Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
This warning was introduced in
commit 81033c6b584b ("ALSA: core: Warn on empty module").
It looks like we are supposed to set card->owner to THIS_MODULE.
A new warning in Clang points out that the initialization of
mux_pll_src_4plls_p appears incorrect:
../drivers/clk/rockchip/clk-rk3228.c:140:58: warning: suspicious
concatenation of string literals in an array initialization; did you
mean to separate the elements with a comma? [-Wstring-concatenation]
PNAME(mux_pll_src_4plls_p) = { "cpll", "gpll", "hdmiphy" "usb480m" };
^
,
../drivers/clk/rockchip/clk-rk3228.c:140:48: note: place parentheses
around the string literal to silence warning
PNAME(mux_pll_src_4plls_p) = { "cpll", "gpll", "hdmiphy" "usb480m" };
^
1 warning generated.
Given the name of the variable and the same variable name in rv1108, it
seems that this should have been four distinct elements. Fix it up by
adding the comma as suggested.
Fixes: 307a2e9ac524 ("clk: rockchip: add clock controller for rk3228") Link: https://github.com/ClangBuiltLinux/linux/issues/1123 Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Link: https://lore.kernel.org/r/20200810044020.2063350-1-natechancellor@gmail.com Reviewed-by: Heiko Stübner <heiko@sntech.de> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
In Documentation/virt/kvm/api.rst it is said that "You probably want to
use 0 as machine type", which implies that type 0 be the "automatic" or
"default" type. And, in user-space libvirt use the null-machine (with
type 0) to detect the kvm capability, which returns "KVM not supported"
on a VZ platform.
I try to fix it in QEMU but it is ugly:
https://lists.nongnu.org/archive/html/qemu-devel/2020-08/msg05629.html
And Thomas Huth suggests me to change the definition of kvm type:
https://lists.nongnu.org/archive/html/qemu-devel/2020-09/msg03281.html
Since VZ and TE cannot co-exists, using type 0 on a TE platform will
still return success (so old user-space tools have no problems on new
kernels); the advantage is that using type 0 on a VZ platform will not
return failure. So, the only problem is "new user-space tools use type
2 on old kernels", but if we treat this as a kernel bug, we can backport
this patch to old stable kernels.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Message-Id: <1599734031-28746-1-git-send-email-chenhc@lemote.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
In the prepare_message callback the bus driver has the
opportunity to split a transfer into smaller chunks.
spi_map_msg is done after prepare_message.
Function spi_res_release releases the splited transfers
in the message. Therefore spi_res_release should be called
after spi_map_msg.
The previous try at this was commit c9ba7a16d0f1
which released the splited transfers after
spi_finalize_current_message had been called.
This introduced a race since the message struct could be
out of scope because the spi_sync call got completed.
Fixes this leak on spi bus driver spi-bcm2835.c when transfer
size is greater than 65532:
Signed-off-by: Gustav Wiklander <gustavwi@axis.com> Link: https://lore.kernel.org/r/20200908151129.15915-1-gustav.wiklander@axis.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
If something goes wrong (such as the SCL being stuck low) then we need
to reset the PCA chip. The issue with this is that on reset we lose all
config settings and the chip ends up in a disabled state which results
in a lock up/high CPU usage. We need to re-apply any configuration that
had previously been set and re-enable the chip.
Signed-off-by: Evan Nimmo <evan.nimmo@alliedtelesis.co.nz> Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
Reading past end of file returns EOF for aligned reads but -EINVAL for
unaligned reads on f2fs. While documentation is not strict about this
corner case, most filesystem returns EOF on this case, like iomap
filesystems. This patch consolidates the behavior for f2fs, by making
it return EOF(0).
it can be verified by a read loop on a file that does a partial read
before EOF (A file that doesn't end at an aligned address). The
following code fails on an unaligned file on f2fs, but not on
btrfs, ext4, and xfs.
while (done < total) {
ssize_t delta = pread(fd, buf + done, total - done, off + done);
if (!delta)
break;
...
}
It is arguable whether filesystems should actually return EOF or
-EINVAL, but since iomap filesystems support it, and so does the
original DIO code, it seems reasonable to consolidate on that.
Signed-off-by: Gabriel Krisman Bertazi <krisman@collabora.com> Reviewed-by: Chao Yu <yuchao0@huawei.com> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
If the sbi->ckpt->next_free_nid is not NAT block aligned and if there
are free nids in that NAT block between the start of the block and
next_free_nid, then those free nids will not be scanned in scan_nat_page().
This results into mismatch between nm_i->available_nids and the sum of
nm_i->free_nid_count of all NAT blocks scanned. And nm_i->available_nids
will always be greater than the sum of free nids in all the blocks.
Under this condition, if we use all the currently scanned free nids,
then it will loop forever in f2fs_alloc_nid() as nm_i->available_nids
is still not zero but nm_i->free_nid_count of that partially scanned
NAT block is zero.
Fix this to align the nm_i->next_scan_nid to the first nid of the
corresponding NAT block.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org> Reviewed-by: Chao Yu <yuchao0@huawei.com> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
This happens because Kyber doesn't track flush requests, so
kyber_finish_request() reads a garbage domain token. Only call the
scheduler's requeue_request() hook if RQF_ELVPRIV is set (like we do for
the finish_request() hook in blk_mq_free_request()). Now that we're
handling it in blk-mq, also remove the check from BFQ.
Reported-by: Yang Yang <yang.yang@vivo.com> Signed-off-by: Omar Sandoval <osandov@fb.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
I found this when compiling a kbuild random config with GCC 11. The
config enables CONFIG_DEBUG_SECTION_MISMATCH, which sets CFLAGS
-fno-inline-functions-called-once. This causes the call to cache_loop in
cache.c to not be inlined causing the below compile error.
In file included from arch/openrisc/mm/cache.c:13:
arch/openrisc/mm/cache.c: In function 'cache_loop':
./arch/openrisc/include/asm/spr.h:16:27: warning: 'asm' operand 0 probably does not match constraints
16 | #define mtspr(_spr, _val) __asm__ __volatile__ ( \
| ^~~~~~~
arch/openrisc/mm/cache.c:25:3: note: in expansion of macro 'mtspr'
25 | mtspr(reg, line);
| ^~~~~
./arch/openrisc/include/asm/spr.h:16:27: error: impossible constraint in 'asm'
16 | #define mtspr(_spr, _val) __asm__ __volatile__ ( \
| ^~~~~~~
arch/openrisc/mm/cache.c:25:3: note: in expansion of macro 'mtspr'
25 | mtspr(reg, line);
| ^~~~~
make[1]: *** [scripts/Makefile.build:283: arch/openrisc/mm/cache.o] Error 1
The asm constraint "K" requires a immediate constant argument to mtspr,
however because of no inlining a register argument is passed causing a
failure. Fix this by using __always_inline.
Link: https://lore.kernel.org/lkml/202008200453.ohnhqkjQ%25lkp@intel.com/ Signed-off-by: Stafford Horne <shorne@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
If during cifs_lookup()/get_inode_info() we encounter a DFS link
and we use the cifsacl or modefromsid mount options we must suppress
any -EREMOTE errors that triggers or else we will not be able to follow
the DFS link and automount the target.
This fixes an issue with modefromsid/cifsacl where these mountoptions
would break DFS and we would no longer be able to access the share.
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com> Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
Enabling a whole subsystem from a single driver 'select' is frowned
upon and won't be accepted in new drivers, that need to use 'depends on'
instead. Existing selection of DMAENGINES will then cause circular
dependencies. Replace them with a dependency.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
Since p points at raw xdr data, there's no guarantee that it's NULL
terminated, so we should give a length. And probably escape any special
characters too.
Reported-by: Zhi Li <yieli@redhat.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
If a write delegation isn't available, the Linux NFS client uses
a zero-stateid when performing a SETATTR.
NFSv4.0 provides no mechanism for an NFS server to match such a
request to a particular client. It recalls all delegations for that
file, even delegations held by the client issuing the request. If
that client happens to hold a read delegation, the server will
recall it immediately, resulting in an NFS4ERR_DELAY/CB_RECALL/
DELEGRETURN sequence.
Optimize out this pipeline bubble by having the client return any
delegations it may hold on a file before it issues a
SETATTR(zero-stateid) on that file.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
The "tx/rx-transfer - crossing PAGE_SIZE" test always fails when
len=131071 and rx_offset >= 5:
spi-loopback-test spi0.0: Running test tx/rx-transfer - crossing PAGE_SIZE
...
with iteration values: len = 131071, tx_off = 0, rx_off = 3
with iteration values: len = 131071, tx_off = 0, rx_off = 4
with iteration values: len = 131071, tx_off = 0, rx_off = 5
loopback strangeness - rx changed outside of allowed range at: ...a4321000
spi_msg@ffffffd5a4157690
frame_length: 131071
actual_length: 131071
spi_transfer@ffffffd5a41576f8
len: 131071
tx_buf: ffffffd5a4340ffc
Note that rx_offset > 3 can only occur if the SPI controller driver sets
->dma_alignment to a higher value than 4, so most SPI controller drivers
are not affect.
The allocated Rx buffer is of size SPI_TEST_MAX_SIZE_PLUS, which is 132
KiB (assuming 4 KiB pages). This test uses an initial offset into the
rx_buf of PAGE_SIZE - 4, and a len of 131071, so the range expected to
be written in this transfer ends at (4096 - 4) + 5 + 131071 == 132 KiB,
which is also the end of the allocated buffer. But the code which
verifies the content of the buffer reads a byte beyond the allocated
buffer and spuriously fails because this out-of-bounds read doesn't
return the expected value.
Fix this by using ITERATE_LEN instead of ITERATE_MAX_LEN to avoid
testing sizes which cause out-of-bounds reads.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com> Link: https://lore.kernel.org/r/20200902132341.7079-1-vincent.whitchurch@axis.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
If the zero duty cycle doesn't correspond to any voltage in the voltage
table, the PWM regulator returns an -EINVAL from get_voltage_sel() which
results in the core erroring out with a "failed to get the current
voltage" and ending up not applying the machine constraints.
Instead, return -ENOTRECOVERABLE which makes the core set the voltage
since it's at an unknown value.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com> Link: https://lore.kernel.org/r/20200902130952.24880-1-vincent.whitchurch@axis.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
The driver is unable to successfully login with remote device. During pt2pt
login, the driver completes its FLOGI request with the remote device having
WWN precedence. The remote device issues its own (delayed) FLOGI after
accepting the driver's and, upon transmitting the FLOGI, immediately
recognizes it has already processed the driver's FLOGI thus it transitions
to sending a PLOGI before waiting for an ACC to its FLOGI.
In the driver, the FLOGI is received and an ACC sent, followed by the PLOGI
being received and an ACC sent. The issue is that the PLOGI reception
occurs before the response from the adapter from the FLOGI ACC is
received. Processing of the PLOGI sets state flags to perform the REG_RPI
mailbox command and proceed with the rest of discovery on the port. The
same completion routine used by both FLOGI and PLOGI is generic in
nature. One of the things it does is clear flags, and those flags happen to
drive the rest of discovery. So what happened was the PLOGI processing set
the flags, the FLOGI ACC completion cleared them, thus when the PLOGI ACC
completes it doesn't see the flags and stops.
Fix by modifying the generic completion routine to not clear the rest of
discovery flag (NLP_ACC_REGLOGIN) unless the completion is also associated
with performing a mailbox command as part of its handling. For things such
as FLOGI ACC, there isn't a subsequent action to perform with the adapter,
thus there is no mailbox cmd ptr. PLOGI ACC though will perform REG_RPI
upon completion, thus there is a mailbox cmd ptr.
Link: https://lore.kernel.org/r/20200828175332.130300-3-james.smart@broadcom.com Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
Link:
https://lore.kernel.org/r/20200825093940.19612-1-jhasan@marvell.com Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Javed Hasan <jhasan@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
When pm8001_tag_alloc() fails, task should be freed just like it is done in
the subsequent error paths.
Link: https://lore.kernel.org/r/20200823091453.4782-1-dinghao.liu@zju.edu.cn Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com> Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
A client should be able to handle getting an ERR_DELAY error
while doing a LOCK call to reclaim state due to delegation being
recalled. This is a transient error that can happen due to server
moving its volumes and invalidating its file location cache and
upon reference to it during the LOCK call needing to do an
expensive lookup (leading to an ERR_DELAY error on a PUTFH).
Signed-off-by: Olga Kornievskaia <kolga@netapp.com> Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
When using vf_ops->ndo_select_queue, the number of queues of VF is
usually bigger than the synthetic NIC. This condition may happen
often.
Remove "unlikely" from the comparison of ndev->real_num_tx_queues.
Fixes: b3bf5666a510 ("hv_netvsc: defer queue selection to VF") Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
pskb_carve_frag_list() may return -ENOMEM in pskb_carve_inside_nonlinear().
we should handle this correctly or we would get wrong sk_buff.
Fixes: 6fa01ccd8830 ("skbuff: Add pskb_extract() helper function") Signed-off-by: Miaohe Lin <linmiaohe@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
The driver for Marvell switches puts all ports in IGMP snooping mode
which results in all IGMP/MLD frames that ingress on the ports to be
forwarded to the CPU only.
The bridge code in the kernel can then interpret these frames and act
upon them, for instance by updating the mdb in the switch to reflect
multicast memberships of stations connected to the ports. However,
the IGMP/MLD frames must then also be forwarded to other ports of the
bridge so external IGMP queriers can track membership reports, and
external multicast clients can receive query reports from foreign IGMP
queriers.
Currently, this is impossible as the EDSA tagger sets offload_fwd_mark
on the skb when it unwraps the tagged frames, and that will make the
switchdev layer prevent the skb from egressing on any other port of
the same switch.
To fix that, look at the To_CPU code in the DSA header and make
forwarding of the frame possible for trapped IGMP packets.
Introduce some #defines for the frame types to make the code a bit more
comprehensive.
Signed-off-by: Daniel Mack <daniel@zonque.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Cc: DENG Qingfang <dqfext@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
Since transactions may be freed shortly after they're created, before
a log_flush occurs, we need to initialize their ail1 and ail2 lists
earlier. Before this patch, the ail1 list was initialized in gfs2_log_flush().
This moves the initialization to the point when the transaction is first
created.
Signed-off-by: Bob Peterson <rpeterso@redhat.com> Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Cc: Salvatore Bonaccorso <carnil@debian.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
Using gcov to collect coverage data for kernels compiled with GCC 10.1
causes random malfunctions and kernel crashes. This is the result of a
changed GCOV_COUNTERS value in GCC 10.1 that causes a mismatch between
the layout of the gcov_info structure created by GCC profiling code and
the related structure used by the kernel.
Fix this by updating the in-kernel GCOV_COUNTERS value. Also re-enable
config GCOV_KERNEL for use with GCC 10.
Reported-by: Colin Ian King <colin.king@canonical.com> Reported-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: Peter Oberparleiter <oberpar@linux.ibm.com> Tested-by: Leon Romanovsky <leonro@nvidia.com> Tested-and-Acked-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
Disable the RPTR shadow across all targets. It will be selectively
re-enabled later for targets that need it.
Cc: stable@vger.kernel.org Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org> Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
The GPU has no business writing into the ringbuffer, let's make it
readonly to the GPU.
Fixes: 7198e6b03155 ("drm/msm: add a3xx gpu support") Signed-off-by: Rob Clark <robdclark@chromium.org> Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org> Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
Failing probe with -EPROBE_DEFER until all dependencies
listed in the _DEP (Operation Region Dependencies) object
have been met.
This will fix an issue where on some platforms UCSI ACPI
driver fails to probe because the address space handler for
the operation region that the UCSI ACPI interface uses has
not been loaded yet.
Fixes: 8243edf44152 ("usb: typec: ucsi: Add ACPI driver") Cc: stable@vger.kernel.org Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Link: https://lore.kernel.org/r/20200904110918.51546-1-heikki.krogerus@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
Userspace drivers that use a SetConfiguration() request to "lightweight"
reset an already configured usb device might cause data toggles to get out
of sync between the device and host, and the device becomes unusable.
The xHCI host requires endpoints to be dropped and added back to reset the
toggle. If USB core notices the new configuration is the same as the
current active configuration it will avoid these extra steps by calling
usb_reset_configuration() instead of usb_set_configuration().
A SetConfiguration() request will reset the device side data toggles.
Make sure usb_reset_configuration() function also drops and adds back the
endpoints to ensure data toggles are in sync.
To avoid code duplication split the current usb_disable_device() function
and reuse the endpoint specific part.
Cc: stable <stable@vger.kernel.org> Tested-by: Martin Thierer <mthierer@gmail.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20200901082528.12557-1-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
The purpose of each TTY is as follows:
* ttyUSB0: DIAG/QCDM port.
* ttyUSB1: GNSS data.
* ttyUSB2: AT-capable port (control).
* ttyUSB3: AT-capable port (data).
In the secondary layout with PID=0x9206 (AT+CUSBSELNV=86) the module
exposes 6 TTY ports:
The purpose of each TTY is as follows:
* ttyUSB0: DIAG/QCDM port.
* ttyUSB1: GNSS data.
* ttyUSB2: AT-capable port (control).
* ttyUSB3: QFLOG interface.
* ttyUSB4: DAM interface.
* ttyUSB5: AT-capable port (data).
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es> Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
The USB composition, defining the set of exported functions, is dynamic
in newer Quectel modems. Default functions can be disabled and
alternative functions can be enabled instead. The alternatives
includes class functions using interface pairs, which should be
handled by the respective class drivers.
Active interfaces are numbered consecutively, so static
blacklisting based on interface numbers will fail when the
composition changes. An example of such an error, where the
option driver has bound to the CDC ECM data interface,
preventing cdc_ether from handling this function:
Change rules for EC21, EC25, BG96 and EG95 to match vendor specific
serial functions only, to prevent binding to class functions. Require
2 endpoints on ff/ff/ff functions, avoiding the 3 endpoint QMI/RMNET
network functions.
Cc: AceLan Kao <acelan.kao@canonical.com> Cc: Sebastian Sjoholm <ssjoholm@mac.com> Cc: Dan Williams <dcbw@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
The USB device descriptor may get changed between two consecutive
enumerations on the same device for some reason, such as DFU or
malicius device.
In that case, we may access the changing descriptor if we don't take
the device lock here.
There were some problem in ipq8074 Gen2 PCIe phy init sequence.
1. Few register values were wrongly updated in the phy init sequence.
2. The register QSERDES_RX_SIGDET_CNTRL is a RX tuning parameter
register which is added in serdes table causing the wrong register
was getting updated.
3. Clocks and resets were not added in the phy init.
Fix these to make Gen2 PCIe port on ipq8074 devices to work.
The current implementation for gbcodec_mixer_dapm_ctl_put() uses
uninitialized gbvalue for comparison with updated value. This was found
using static analysis with coverity.
Uninitialized scalar variable (UNINIT)
11. uninit_use: Using uninitialized value
gbvalue.value.integer_value[0].
460 if (gbvalue.value.integer_value[0] != val) {
This patch fixes the issue with fetching the gbvalue before using it for
comparision.
Fixes: 6339d2322c47 ("greybus: audio: Add topology parser for GB codec") Reported-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Vaibhav Agarwal <vaibhav.sr@gmail.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/bc4f29eb502ccf93cd2ffd98db0e319fa7d0f247.1597408126.git.vaibhav.sr@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
The '#ifdef MODULE' check in the original commit does not work as intended.
The code under the check is not built at all if CONFIG_DEBUG_FS=y. Fix this
by using a correct check.
Fixes: 275678e7a9be ("debugfs: Check module state before warning in {full/open}_proxy_open()") Signed-off-by: Vladis Dronov <vdronov@redhat.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200811150129.53343-1-vdronov@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
when kmalloc() fails in kvm_io_bus_unregister_dev(), before removing
the bus, we should iterate over all other devices linked to it and call
kvm_iodevice_destructor() for them
Fixes: 90db10434b16 ("KVM: kvm_io_bus_unregister_dev() should never fail") Cc: stable@vger.kernel.org Reported-and-tested-by: syzbot+f196caa45793d6374707@syzkaller.appspotmail.com Link: https://syzkaller.appspot.com/bug?extid=f196caa45793d6374707 Signed-off-by: Rustam Kovhaev <rkovhaev@gmail.com> Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20200907185535.233114-1-rkovhaev@gmail.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
For the obscure cases where PMD and PUD are the same size
(64kB pages with 42bit VA, for example, which results in only
two levels of page tables), we can't map anything as a PUD,
because there is... erm... no PUD to speak of. Everything is
either a PMD or a PTE.
So let's only try and map a PUD when its size is different from
that of a PMD.
Cc: stable@vger.kernel.org Fixes: b8e0ba7c8bea ("KVM: arm64: Add support for creating PUD hugepages at stage 2") Reported-by: Gavin Shan <gshan@redhat.com> Reported-by: Eric Auger <eric.auger@redhat.com> Reviewed-by: Alexandru Elisei <alexandru.elisei@arm.com> Reviewed-by: Gavin Shan <gshan@redhat.com> Tested-by: Gavin Shan <gshan@redhat.com> Tested-by: Eric Auger <eric.auger@redhat.com> Tested-by: Alexandru Elisei <alexandru.elisei@arm.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
According to SDM 27.2.4, Event delivery causes an APIC-access VM exit.
Don't report internal error and freeze guest when event delivery causes
an APIC-access exit, it is handleable and the event will be re-injected
during the next vmentry.
Signed-off-by: Wanpeng Li <wanpengli@tencent.com>
Message-Id: <1597827327-25055-2-git-send-email-wanpengli@tencent.com> Cc: stable@vger.kernel.org Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
Yunhai Zhang recently fixed a VGA software scrollback bug in commit ebfdfeeae8c0 ("vgacon: Fix for missing check in scrollback handling"),
but that then made people look more closely at some of this code, and
there were more problems on the vgacon side, but also the fbcon software
scrollback.
We don't really have anybody who maintains this code - probably because
nobody actually _uses_ it any more. Sure, people still use both VGA and
the framebuffer consoles, but they are no longer the main user
interfaces to the kernel, and haven't been for decades, so these kinds
of extra features end up bitrotting and not really being used.
So rather than try to maintain a likely unused set of code, I'll just
aggressively remove it, and see if anybody even notices. Maybe there
are people who haven't jumped on the whole GUI badnwagon yet, and think
it's just a fad. And maybe those people use the scrollback code.
If that turns out to be the case, we can resurrect this again, once
we've found the sucker^Wmaintainer for it who actually uses it.
This (and the VGA soft scrollback) turns out to have various nasty small
special cases that nobody really is willing to fight. The soft
scrollback code was really useful a few decades ago when you typically
used the console interactively as the main way to interact with the
machine, but that just isn't the case any more.
So it's not worth dragging along.
Tested-by: Yuan Ming <yuanmingbuaa@gmail.com> Tested-by: Willy Tarreau <w@1wt.eu> Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
If the pkey_table is not available (which is the case when RoCE is not
supported), the cited commit caused a regression where mlx4_devices
without RoCE are not created.
Fix this by returning a pkey table length of zero in procedure
eth_link_query_port() if the pkey-table length reported by the device is
zero.
Link: https://lore.kernel.org/r/20200824110229.1094376-1-leon@kernel.org Cc: <stable@vger.kernel.org> Fixes: 1901b91f9982 ("IB/core: Fix potential NULL pointer dereference in pkey cache") Fixes: fa417f7b520e ("IB/mlx4: Add support for IBoE") Signed-off-by: Mark Bloch <markb@mellanox.com> Reviewed-by: Maor Gottlieb <maorg@nvidia.com> Signed-off-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
This means that images can be mapped and unmapped (i.e. block devices
can be created and deleted) by a UID 0 process even after it drops all
privileges or by any process with CAP_DAC_OVERRIDE in its user namespace
as long as UID 0 is mapped into that user namespace.
Be consistent with other virtual block devices (loop, nbd, dm, md, etc)
and require CAP_SYS_ADMIN in the initial user namespace for mapping and
unmapping, and also for dumping the configuration string and refreshing
the image header.
Cc: stable@vger.kernel.org Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Reviewed-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
Commit b214fe592ab7 ("mmc: sdhci-of-esdhc: add erratum eSDHC7 support")
added code to check for a specific compatible string in the device-tree
on every esdhc interrupat. Instead of doing this record the quirk in
struct sdhci_esdhc and lookup the struct in esdhc_irq.
SDHCI changed from using a tasklet to finish requests, to using an IRQ
thread i.e. commit c07a48c2651965 ("mmc: sdhci: Remove finish_tasklet").
Because this increased the latency to complete requests, a preparatory
change was made to complete the request from the IRQ handler if
possible i.e. commit 19d2f695f4e827 ("mmc: sdhci: Call mmc_request_done()
from IRQ handler if possible"). That alleviated the situation for MMC
block devices because the MMC block driver makes use of mmc_pre_req()
and mmc_post_req() so that successful requests are completed in the IRQ
handler and any DMA unmapping is handled separately in mmc_post_req().
However SDIO was still affected, and an example has been reported with
up to 20% degradation in performance.
Looking at SDIO I/O helper functions, sdio_io_rw_ext_helper() appeared
to be a possible candidate for making use of asynchronous requests
within its I/O loops, but analysis revealed that these loops almost
never iterate more than once, so the complexity of the change would not
be warrented.
Instead, mmc_pre_req() and mmc_post_req() are added before and after I/O
submission (mmc_wait_for_req) in mmc_io_rw_extended(). This still has
the potential benefit of reducing the duration of interrupt handlers, as
well as addressing the latency issue for SDHCI. It also seems a more
reasonable solution than forcing drivers to do everything in the IRQ
handler.
Temporarily disable preemption on a5xx targets pending some improvements
to protect the RPTR shadow from being corrupted.
Cc: stable@vger.kernel.org Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org> Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
The TVE200 will occasionally print a bunch of lost interrupts
and similar dmesg messages, sometimes during boot and sometimes
after disabling and coming back to enablement. This is probably
because the hardware is left in an unknown state by the boot
loader that displays a logo.
This can be fixed by bringing the controller into a known state
by resetting the controller while enabling it. We retry reset 5
times like the vendor driver does. We also put the controller
into reset before de-clocking it and clear all interrupts before
enabling the vblank IRQ.
This makes the video enable/disable/enable cycle rock solid
on the D-Link DIR-685. Tested extensively.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: stable@vger.kernel.org Link: https://patchwork.freedesktop.org/patch/msgid/20200820203144.271081-1-linus.walleij@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
1. Initiator A tries to log in to iqn1-tpg1 on port 3260. After finishing
PDU exchange in the login thread and before the negotiation is finished
the the network link goes down. At this point A has not finished login
and tpg->np_login_sem is held.
2. Initiator B tries to log in to iqn2-tpg1 on port 3260. After finishing
PDU exchange in the login thread the target expects to process remaining
login PDUs in workqueue context.
3. Initiator A' tries to log in to iqn1-tpg1 on port 3260 from a new
socket. A' will wait for tpg->np_login_sem with np->np_login_timer
loaded to wait for at most 15 seconds. The lock is held by A so A'
eventually times out.
4. Before A' got timeout initiator B gets negotiation failed and calls
iscsi_target_login_drop()->iscsi_target_login_sess_out(). The
np->np_login_timer is canceled and initiator A' will hang forever.
Because A' is now in the login thread, no new login requests can be
serviced.
Fix this by moving iscsi_stop_login_thread_timer() out of
iscsi_target_login_sess_out(). Also remove iscsi_np parameter from
iscsi_target_login_sess_out().
Link: https://lore.kernel.org/r/20200729130343.24976-1-houpu@bytedance.com Cc: stable@vger.kernel.org Reviewed-by: Mike Christie <michael.christie@oracle.com> Signed-off-by: Hou Pu <houpu@bytedance.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
Current code does not consider 'page_off' in data digest calculation. To
fix this, add a local variable 'first_sg' and set first_sg.offset to
sg->offset + page_off.
Link: https://lore.kernel.org/r/1598358910-3052-1-git-send-email-varun@chelsio.com Fixes: e48354ce078c ("iscsi-target: Add iSCSI fabric support for target v4.1") Cc: <stable@vger.kernel.org> Reviewed-by: Mike Christie <michael.christie@oralce.com> Signed-off-by: Varun Prakash <varun@chelsio.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
The recent commit 7d8196641ee1 ("regulator: Remove pointer table
overallocation") changed the size of coupled_rdevs and now KASAN is able
to detect slab-out-of-bounds problem in regulator_unlock_recursive(),
which is a legit problem caused by a typo in the code. The recursive
unlock function uses n_coupled value of a parent regulator for unlocking
supply regulator, while supply's n_coupled should be used. In practice
problem may only affect platforms that use coupled regulators.
Cc: stable@vger.kernel.org # 5.0+ Fixes: f8702f9e4aa7 ("regulator: core: Use ww_mutex for regulators locking") Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Link: https://lore.kernel.org/r/20200831204335.19489-1-digetx@gmail.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
By calling device_initialize() earlier and noting that kfree(NULL) is
ok, we can save a bit of code in error handling and plug of_node leak.
Fixed commit already did part of the work.
Fixes: 9177514ce349 ("regulator: fix memory leak on error path of regulator_register()") Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Reviewed-by: Vladimir Zapolskiy <vz@mleia.com> Acked-by: Vladimir Zapolskiy <vz@mleia.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/f5035b1b4d40745e66bacd571bbbb5e4644d21a1.1597195321.git.mirq-linux@rere.qmqm.pl Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
Pull regulator_list_mutex into set_consumer_device_supply() and keep
allocations outside of it. Fourth of the fs_reclaim deadlock case.
Fixes: 45389c47526d ("regulator: core: Add early supply resolution for regulators") Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/f0380bdb3d60aeefa9693c4e234d2dcda7e56747.1597195321.git.mirq-linux@rere.qmqm.pl Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
projects / mirror_ubuntu-focal-kernel.git / log