Paolo Abeni [Wed, 17 Feb 2016 18:30:01 +0000 (19:30 +0100)]
lwt: fix rx checksum setting for lwt devices tunneling over ipv6
the commit 35e2d1152b22 ("tunnels: Allow IPv6 UDP checksums to be
correctly controlled.") changed the default xmit checksum setting
for lwt vxlan/geneve ipv6 tunnels, so that now the checksum is not
set into external UDP header.
This commit changes the rx checksum setting for both lwt vxlan/geneve
devices created by openvswitch accordingly, so that lwt over ipv6
tunnel pairs are again able to communicate with default values.
Signed-off-by: Paolo Abeni <pabeni@redhat.com> Acked-by: Jiri Benc <jbenc@redhat.com> Acked-by: Jesse Gross <jesse@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 19 Feb 2016 20:35:29 +0000 (15:35 -0500)]
Merge tag 'batman-adv-fix-for-davem' of git://git.open-mesh.org/linux-merge
Antonio Quartulli says:
====================
Two of the fixes included in this patchset prevent wrong memory
access - it was triggered when removing an object from a list
after it was already free'd due to bad reference counting.
This misbehaviour existed for both the gw_node and the
orig_node_vlan object and has been fixed by Sven Eckelmann.
The last patch fixes our interface feasibility check and prevents
it from looping indefinitely when two net_device objects
reference each other via iflink index (i.e. veth pair), by
Andrew Lunn
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Anton Protopopov [Wed, 17 Feb 2016 02:43:16 +0000 (21:43 -0500)]
rtnl: RTM_GETNETCONF: fix wrong return value
An error response from a RTM_GETNETCONF request can return the positive
error value EINVAL in the struct nlmsgerr that can mislead userspace.
Signed-off-by: Anton Protopopov <a.s.protopopov@gmail.com> Acked-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: make netdev_for_each_lower_dev safe for device removal
When I used netdev_for_each_lower_dev in commit bad531623253 ("vrf:
remove slave queue and private slave struct") I thought that it acts
like netdev_for_each_lower_private and can be used to remove the current
device from the list while walking, but unfortunately it acts more like
netdev_for_each_lower_private_rcu and doesn't allow it. The difference
is where the "iter" points to, right now it points to the current element
and that makes it impossible to remove it. Change the logic to be
similar to netdev_for_each_lower_private and make it point to the "next"
element so we can safely delete the current one. VRF is the only such
user right now, there's no change for the read-only users.
CC: David Ahern <dsa@cumulusnetworks.com> CC: David S. Miller <davem@davemloft.net> CC: Roopa Prabhu <roopa@cumulusnetworks.com> CC: Vlad Yasevich <vyasevic@redhat.com> Fixes: bad531623253 ("vrf: remove slave queue and private slave struct") Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Reviewed-by: David Ahern <dsa@cumulusnetworks.com> Tested-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Wed, 17 Feb 2016 22:25:11 +0000 (23:25 +0100)]
USB: cdc_subset: only build when one driver is enabled
This avoids a harmless randconfig warning I get when USB_NET_CDC_SUBSET
is enabled, but all of the more specific drivers are not:
drivers/net/usb/cdc_subset.c:241:2: #warning You need to configure some hardware for this driver
The current behavior is clearly intentional, giving a warning when
a user picks a configuration that won't do anything good. The only
reason for even addressing this is that I'm getting close to
eliminating all 'randconfig' warnings on ARM, and this came up
a couple of times.
My workaround is to not even build the module when none of the
configurations are enable.
Alternatively we could simply remove the #warning (nothing wrong
for compile-testing), turn it into a runtime warning, or
change the Kconfig options into a menu to hide CONFIG_USB_NET_CDC_SUBSET.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Benc [Tue, 16 Feb 2016 21:18:26 +0000 (22:18 +0100)]
vxlan: do not use fdb in metadata mode
In metadata mode, the vxlan interface is not supposed to use the fdb control
plane but an external one (openvswitch or static routes). With the current
code, packets may leak into the fdb handling code which usually causes them
to be dropped anyway but may have strange side effects.
Just drop the packets directly when in metadata mode if the destination data
are not correctly provided on egress.
Signed-off-by: Jiri Benc <jbenc@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Anton Protopopov [Wed, 17 Feb 2016 16:19:56 +0000 (11:19 -0500)]
mISDN: prevent possible NULL pointer dereference
A return value of the bchannel_get_rxbuf() function is compared with the
positive ENOMEM value instead of the negative -ENOMEM value to detect a
memory allocation problem. Thus, after a possible memory allocation
failure the bc->bch.rx_skb will be NULL which will lead to a NULL
pointer dereference.
Signed-off-by: Anton Protopopov <a.s.protopopov@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Failure of kzalloc should cause the enclosing function
to return -ENOMEM, not -ENODEV.
Additionally, removed the following checkpatch warnings:
ERROR: spaces required around that '==' (ctx:VxV)
ERROR: space required before the open parenthesis '('
CHECK: Comparison to NULL could be written "!lp"
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Phil Sutter [Wed, 17 Feb 2016 14:37:43 +0000 (15:37 +0100)]
IFF_NO_QUEUE: Fix for drivers not calling ether_setup()
My implementation around IFF_NO_QUEUE driver flag assumed that leaving
tx_queue_len untouched (specifically: not setting it to zero) by drivers
would make it possible to assign a regular qdisc to them without having
to worry about setting tx_queue_len to a useful value. This was only
partially true: I overlooked that some drivers don't call ether_setup()
and therefore not initialize tx_queue_len to the default value of 1000.
Consequently, removing the workarounds in place for that case in qdisc
implementations which cared about it (namely, pfifo, bfifo, gred, htb,
plug and sfb) leads to problems with these specific interface types and
qdiscs.
Luckily, there's already a sanitization point for drivers setting
tx_queue_len to zero, which can be reused to assign the fallback value
most qdisc implementations used, which is 1.
Fixes: 348e3435cbefa ("net: sched: drop all special handling of tx_queue_len == 0") Tested-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Signed-off-by: Phil Sutter <phil@nwl.cc> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 18 Feb 2016 13:39:18 +0000 (05:39 -0800)]
tcp/dccp: fix another race at listener dismantle
Ilya reported following lockdep splat:
kernel: =========================
kernel: [ BUG: held lock freed! ]
kernel: 4.5.0-rc1-ceph-00026-g5e0a311 #1 Not tainted
kernel: -------------------------
kernel: swapper/5/0 is freeing memory ffff880035c9d200-ffff880035c9dbff, with a lock still held there!
kernel: (&(&queue->rskq_lock)->rlock){+.-...}, at:
[<ffffffff816f6a88>] inet_csk_reqsk_queue_add+0x28/0xa0
kernel: 4 locks held by swapper/5/0:
kernel: #0: (rcu_read_lock){......}, at: [<ffffffff8169ef6b>]
netif_receive_skb_internal+0x4b/0x1f0
kernel: #1: (rcu_read_lock){......}, at: [<ffffffff816e977f>]
ip_local_deliver_finish+0x3f/0x380
kernel: #2: (slock-AF_INET){+.-...}, at: [<ffffffff81685ffb>]
sk_clone_lock+0x19b/0x440
kernel: #3: (&(&queue->rskq_lock)->rlock){+.-...}, at:
[<ffffffff816f6a88>] inet_csk_reqsk_queue_add+0x28/0xa0
To properly fix this issue, inet_csk_reqsk_queue_add() needs
to return to its callers if the child as been queued
into accept queue.
We also need to make sure listener is still there before
calling sk->sk_data_ready(), by holding a reference on it,
since the reference carried by the child can disappear as
soon as the child is put on accept queue.
Reported-by: Ilya Dryomov <idryomov@gmail.com> Fixes: ebb516af60e1 ("tcp/dccp: fix race at listener dismantle phase") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Thu, 18 Feb 2016 13:21:19 +0000 (21:21 +0800)]
route: check and remove route cache when we get route
Since the gc of ipv4 route was removed, the route cached would has
no chance to be removed, and even it has been timeout, it still could
be used, cause no code to check it's expires.
Fix this issue by checking and removing route cache when we get route.
Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Jamal Hadi Salim [Thu, 18 Feb 2016 12:38:04 +0000 (07:38 -0500)]
net_sched fix: reclassification needs to consider ether protocol changes
actions could change the etherproto in particular with ethernet
tunnelled data. Typically such actions, after peeling the outer header,
will ask for the packet to be reclassified. We then need to restart
the classification with the new proto header.
Example setup used to catch this:
sudo tc qdisc add dev $ETH ingress
sudo $TC filter add dev $ETH parent ffff: pref 1 protocol 802.1Q \
u32 match u32 0 0 flowid 1:1 \
action vlan pop reclassify
Fixes: 3b3ae880266d ("net: sched: consolidate tc_classify{,_compat}") Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Thu, 18 Feb 2016 10:30:02 +0000 (11:30 +0100)]
mlxsw: spectrum: Allow for PVID deletion
When PVID is toggled off on a port member in a VLAN filtering bridge or
the PVID VLAN is deleted, make the port drop untagged packets. Reverse
the operation when PVID is toggled back on.
Set the PVID back to the default (1), when leaving the bridge so that
untagged traffic will be directed to the CPU.
Fixes: 56ade8fe3fe1 ("mlxsw: spectrum: Add initial support for Spectrum ASIC") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Thu, 18 Feb 2016 10:30:01 +0000 (11:30 +0100)]
mlxsw: reg: Add the Switch Port Acceptable Frame Types register
When VLAN filtering is enabled on a bridge and PVID is deleted from a
bridge port, then untagged frames are not allowed to ingress into the
bridge from this port.
Add the Switch Port Acceptable Frame Types (SPAFT) register, which
configures the frame admittance of the port.
Fixes: 56ade8fe3fe1 ("mlxsw: spectrum: Add initial support for Spectrum ASIC") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sunil Goutham [Tue, 16 Feb 2016 10:59:51 +0000 (16:29 +0530)]
net: thunderx: Fix receive packet stats
Counting rx packets for every CQE_RX in CQ irq handler is incorrect.
Synchronization is missing when multiple queues are receiving packets
simultaneously. Like transmit packet stats use HW stats here.
Also removed unused 'cqe_type' parameter in nicvf_rcv_pkt_handler().
Signed-off-by: Sunil Goutham <sgoutham@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sunil Goutham [Tue, 16 Feb 2016 10:59:49 +0000 (16:29 +0530)]
net: thunderx: Fix for multiqset not configured upon interface toggle
When a interface is assigned morethan 8 queues and the logical interface
is toggled i.e down & up, additional queues or qsets are not initialized
as secondary qset count is being set to zero while tearing down.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Thu, 18 Feb 2016 02:43:22 +0000 (18:43 -0800)]
net: dsa: Unregister slave_dev in error path
With commit 0071f56e46da ("dsa: Register netdev before phy"), we are now trying
to free a network device that has been previously registered, and in case of
errors, this will make us hit the BUG_ON(dev->reg_state != NETREG_UNREGISTERED)
condition.
Fix this by adding a missing unregister_netdev() before free_netdev().
Fixes: 0071f56e46da ("dsa: Register netdev before phy") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Clemens Gruber [Mon, 15 Feb 2016 22:46:45 +0000 (23:46 +0100)]
phy: marvell: Fix and unify reg-init behavior
For the Marvell 88E1510, marvell_of_reg_init was called too late, in the
config_aneg function.
Since commit 113c74d83eef ("net: phy: turn carrier off on phy attach"),
this lead to the link not coming up at boot anymore, due to the phy
state machine being stuck at waiting for interrupts (off by default on
the 88E1510).
For seven other Marvell PHYs, marvell_of_reg_init was not called at all.
Add a generic marvell_config_init function, which in turn calls
marvell_of_reg_init.
PHYs, which already have a specific config_init function with a call to
marvell_of_reg_init, are left untouched. The generic marvell_config_init
function is called for all the others, to get consistent behavior across
all Marvell PHYs.
Fixes: 113c74d83eef ("net: phy: turn carrier off on phy attach") Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
ravb: Update DT binding example for final CPG/MSSR bindings
The example in the DT binding documentation uses the preliminary DT
bindings for the r8a7795 MSTP clocks, which never went upstream.
Update the example to use the DT bindings for the upstream Clock Pulse
Generator / Module Standby and Software Reset hardware block.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Mon, 15 Feb 2016 12:19:54 +0000 (13:19 +0100)]
mlxsw: spectrum: Set STP state when leaving 802.1D bridge
When a VLAN device leaves a bridge its STP state is set to DISABLED,
which causes the hardware to discard any packets coming through the port
with this VLAN.
Fix that by setting STP state to FORWARDING when the device leaves its
bridge and allow traffic to be directed to CPU.
Fixes: 26f0e7fb15de ("mlxsw: spectrum: Add support for VLAN devices bridging") Reported-by: Elad Raz <eladr@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Mark Tomlinson [Mon, 15 Feb 2016 03:24:44 +0000 (16:24 +1300)]
l2tp: Fix error creating L2TP tunnels
A previous commit (33f72e6) added notification via netlink for tunnels
when created/modified/deleted. If the notification returned an error,
this error was returned from the tunnel function. If there were no
listeners, the error code ESRCH was returned, even though having no
listeners is not an error. Other calls to this and other similar
notification functions either ignore the error code, or filter ESRCH.
This patch checks for ESRCH and does not flag this as an error.
Reviewed-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz> Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz> Signed-off-by: David S. Miller <davem@davemloft.net>
David Rivshin [Sat, 13 Feb 2016 00:45:36 +0000 (19:45 -0500)]
drivers: net: cpsw-phy-sel: add dev_warn() for unsupported PHY mode
The cpsw-phy-sel driver supports only MII, RMII, and RGMII PHY modes,
and silently handled any other values as if MII was specified. In a
case where the PHY mode was incorrectly specified, or a bug elsewhere,
there would be no indication of a problem. If MII was the correct mode,
then this will go unnoticed, otherwise the symptom will be a failure
to transmit/receive data over the RMII/RGMII link.
Add a dev_warn() to make this condition obvious and provide a
breadcrumb to follow.
Cc: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: David Rivshin <drivshin@allworx.com> Acked-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/mlx4_en: Avoid changing dev->features directly in run-time
It's forbidden to manually change dev->features in run-time. Currently, this is
done in the driver to make sure that GSO_UDP_TUNNEL is advertized only when
VXLAN tunnel is set. However, since the stack actually does features intersection
with hw_enc_features, we can safely revert to advertizing features early when
registering the netdevice.
Fixes: f4a1edd56120 ('net/mlx4_en: Advertize encapsulation offloads [...]') Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Huy Nguyen [Wed, 17 Feb 2016 15:24:26 +0000 (17:24 +0200)]
net/mlx4_core: Set UAR page size to 4KB regardless of system page size
problem description:
The current code sets UAR page size equal to system page size.
The ConnectX-3 and ConnectX-3 Pro HWs require minimum 128 UAR pages.
The mlx4 kernel drivers are not loaded if there is less than 128 UAR pages.
solution:
Always set UAR page to 4KB. This allows more UAR pages if the OS
has PAGE_SIZE larger than 4KB. For example, PowerPC kernel use 64KB
system page size, with 4MB uar region, there are 4MB/2/64KB = 32
uars (half for uar, half for blueflame). This does not meet minimum 128
UAR pages requirement. With 4KB UAR page, there are 4MB/2/4KB = 512 uars
which meet the minimum requirement.
Note that only codes in mlx4_core that deal with firmware know that uar
page size is 4KB. Codes that deal with usr page in cq and qp context
(mlx4_ib, mlx4_en and part of mlx4_core) still have the same assumption
that uar page size equals to system page size.
Note that with this implementation, on 64KB system page size kernel, there
are 16 uars per system page but only one uars is used. The other 15
uars are ignored because of the above assumption.
Regarding SR-IOV, mlx4_core in hypervisor will set the uar page size
to 4KB and mlx4_core code in virtual OS will obtain the uar page size from
firmware.
Regarding backward compatibility in SR-IOV, if hypervisor has this new code,
the virtual OS must be updated. If hypervisor has old code, and the virtual
OS has this new code, the new code will be backward compatible with the
old code. If the uar size is big enough, this new code in VF continues to
work with 64 KB uar page size (on PowerPc kernel). If the uar size does not
meet 128 uars requirement, this new code not loaded in VF and print the same
error message as the old code in Hypervisor.
Signed-off-by: Huy Nguyen <huyn@mellanox.com> Reviewed-by: Yishai Hadas <yishaih@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Jurgens [Wed, 17 Feb 2016 15:24:25 +0000 (17:24 +0200)]
net/mlx4_core: Do not BUG_ON during reset when PCI is offline
The PCI channel could go offline during reset due to EEH. Don't bug on in
this case, the error is recoverable.
Fixes: f6bc11e42646 ('net/mlx4_core: Enhance the catas flow to support device reset') Signed-off-by: Daniel Jurgens <danielj@mellanox.com> Reviewed-by: Yishai Hadas <yishaih@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eran Ben Elisha [Wed, 17 Feb 2016 15:24:24 +0000 (17:24 +0200)]
net/mlx4_core: Fix potential corruption in counters database
The error flow in procedure handle_existing_counter() is wrong.
The procedure should exit after encountering the error, not continue
as if everything is OK.
Fixes: 68230242cdbc ('net/mlx4_core: Add port attribute when tracking counters') Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: David S. Miller <davem@davemloft.net>
net/mlx4_en: Choose time-stamping shift value according to HW frequency
Previously, the shift value used for time-stamping was constant and didn't
depend on the HW chip frequency. Change that to take the frequency into account
and calculate the maximal value in cycles per wraparound of ten seconds. This
time slot was chosen since it gives a good accuracy in time synchronization.
Algorithm for shift value calculation:
* Round up the maximal value in cycles to nearest power of two
* Calculate maximal multiplier by division of all 64 bits set
to above result
* Then, invert the function clocksource_khz2mult() to get the shift from
maximal mult value
Fixes: ec693d47010e ('net/mlx4_en: Add HW timestamping (TS) support') Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com> Reviewed-by: Matan Barak <matanb@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Amir Vadai [Wed, 17 Feb 2016 15:24:22 +0000 (17:24 +0200)]
net/mlx4_en: Count HW buffer overrun only once
RdropOvflw counts overrun of HW buffer, therefore should
be used for rx_fifo_errors only.
Currently RdropOvflw counter is mistakenly also set into
rx_missed_errors and rx_over_errors too, which makes the
device total dropped packets accounting to show wrong results.
Fix that. Use it for rx_fifo_errors only.
Fixes: c27a02cd94d6 ('mlx4_en: Add driver for Mellanox ConnectX 10GbE NIC') Signed-off-by: Amir Vadai <amir@vadai.me> Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 12 Feb 2016 06:50:29 +0000 (22:50 -0800)]
tcp: md5: release request socket instead of listener
If tcp_v4_inbound_md5_hash() returns an error, we must release
the refcount on the request socket, not on the listener.
The bug was added for IPv4 only.
Fixes: 079096f103fac ("tcp/dccp: install syn_recv requests into ehash table") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 11 Feb 2016 16:58:18 +0000 (08:58 -0800)]
tcp: do not set rtt_min to 1
There are some cases where rtt_us derives from deltas of jiffies,
instead of using usec timestamps.
Since we want to track minimal rtt, better to assume a delta of 0 jiffie
might be in fact be very close to 1 jiffie.
It is kind of sad jiffies_to_usecs(1) calls a function instead of simply
using a constant.
Fixes: f672258391b42 ("tcp: track min RTT using windowed min-filter") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Neal Cardwell <ncardwell@google.com> Cc: Yuchung Cheng <ycheng@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sascha Hauer [Thu, 11 Feb 2016 10:44:49 +0000 (11:44 +0100)]
net: dsa: remove phy_disconnect from error path
The phy has not been initialized, disconnecting it in the error
path results in a NULL pointer exception. Drop the phy_disconnect
from the error path.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Acked-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Paul Maloy [Wed, 10 Feb 2016 21:14:57 +0000 (16:14 -0500)]
tipc: fix premature addition of node to lookup table
In commit 5266698661401a ("tipc: let broadcast packet reception
use new link receive function") we introduced a new per-node
broadcast reception link instance. This link is created at the
moment the node itself is created. Unfortunately, the allocation
is done after the node instance has already been added to the node
lookup hash table. This creates a potential race condition, where
arriving broadcast packets are able to find and access the node
before it has been fully initialized, and before the above mentioned
link has been created. The result is occasional crashes in the function
tipc_bcast_rcv(), which is trying to access the not-yet existing link.
We fix this by deferring the addition of the node instance until after
it has been fully initialized in the function tipc_node_create().
Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Wed, 10 Feb 2016 22:33:50 +0000 (17:33 -0500)]
bnxt_en: Reduce default ring sizes.
The current default tx ring size of 512 causes an extra page to be
allocated for the tx ring with only 1 entry in it. Reduce it to
511. The default rx ring size is also reduced to 511 to use less
memory by default.
Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Wed, 10 Feb 2016 22:33:49 +0000 (17:33 -0500)]
bnxt_en: Fix implementation of tx push operation.
tx push is supported for small packets to reduce DMA latency. The
following bugs are fixed in this patch:
1. Fix the definition of the push BD which is different from the DMA BD.
2. The push buffer has to be zero padded to the next 64-bit word boundary
or tx checksum won't be correct.
3. Increase the tx push packet threshold to 164 bytes (192 bytes with the BD)
so that small tunneled packets are within the threshold.
Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Wed, 10 Feb 2016 22:33:47 +0000 (17:33 -0500)]
bnxt_en: Cleanup and Fix flow control setup logic
Cleanup bnxt_probe_phy() to cleanly separate 2 code blocks for autoneg
on and off. Autoneg flow control is possible only if autoneg is enabled.
In bnxt_get_settings(), Pause and Asym_Pause are always supported.
Only the advertisement bits change depending on the ethtool -A setting
in auto mode.
Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Wed, 10 Feb 2016 22:33:46 +0000 (17:33 -0500)]
bnxt_en: Fix ethtool autoneg logic.
1. Determine autoneg on|off setting from link_info->autoneg. Using the
firmware returned setting can be misleading if autoneg is changed and
there hasn't been a phy update from the firmware.
2. If autoneg is disabled, link_info->autoneg should be set to 0 to
indicate both speed and flow control autoneg are disabled.
3. To enable autoneg flow control, speed autoneg must be enabled.
Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Wed, 10 Feb 2016 15:09:02 +0000 (16:09 +0100)]
bridge: mdb: avoid uninitialized variable warning
A recent change to the mdb code confused the compiler to the point
where it did not realize that the port-group returned from
br_mdb_add_group() is always valid when the function returns a nonzero
return value, so we get a spurious warning:
net/bridge/br_mdb.c: In function 'br_mdb_add':
net/bridge/br_mdb.c:542:4: error: 'pg' may be used uninitialized in this function [-Werror=maybe-uninitialized]
__br_mdb_notify(dev, entry, RTM_NEWMDB, pg);
Slightly rearranging the code in br_mdb_add_group() makes the problem
go away, as gcc is clever enough to see that both functions check
for 'ret != 0'.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Fixes: 9e8430f8d60d ("bridge: mdb: Passing the port-group pointer to br_mdb module") Signed-off-by: David S. Miller <davem@davemloft.net>
net: arc_emac: reset txbd_curr and txbd_dirty pointers to zero
EMAC reset internal tx ring pointer to zero at statup.
txbd_curr and txbd_dirty can be different from zero.
That cause ethernet transfer hang (no packets transmitted).
In order to reproduce, run on device:
ifconfig eth0 down
ifconfig eth0 up
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Tue, 9 Feb 2016 14:14:43 +0000 (06:14 -0800)]
net: Copy inner L3 and L4 headers as unaligned on GRE TEB
This patch corrects the unaligned accesses seen on GRE TEB tunnels when
generating hash keys. Specifically what this patch does is make it so that
we force the use of skb_copy_bits when the GRE inner headers will be
unaligned due to NET_IP_ALIGNED being a non-zero value.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com> Acked-by: Tom Herbert <tom@herbertland.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 16 Feb 2016 20:21:48 +0000 (15:21 -0500)]
Merge branch 'mlx5-fixes'
Saeed Mahameed says:
====================
mlx5 driver fixes for 4.5-rc2
We added here a patch from Matan and Alaa for addressing Linus comments on
the mess w.r.t reserved field names in the driver/firmware auto-generated file.
Once the patch hits linus tree, we'll ask Doug to rebase his tree on that
rc so both net-next and rdma-next development for 4.6 will be done under
the fixed robust form.
Also provided two patches that addresses the dynamic ndo initialization
issue of mlx5e netdevice.
Or and Saeed.
changes from V1: (Only first patch was changed)
In this V we fixed the issues addressed in Or's previous e-mail.
1. Offsets took into account two dimensional u8 arrays
2. Offsets took into account nesting unions and structs
3. Offsets for unions
4. Offsets for any reserved field
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed [Tue, 9 Feb 2016 12:57:44 +0000 (14:57 +0200)]
net/mlx5e: Use static constant netdevice ndos
Currently our netdevice ops is a one static global variable which
is referenced by all mlx5e netdevice instances. This can be
problematic when different driver instances do not share same
HW capabilities (e.g SRIOV PF and VFs probed to the host).
Now we have two constant global netdevice ops variables, one
for basic netdevice ops and the other with extended SRIOV ops,
on netdevice construction we choose the one suitable for
current device capabilities.
Fixes: 66e49dedada6 ("net/mlx5e: Add support for SR-IOV ndos") Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matan Barak [Tue, 9 Feb 2016 12:57:42 +0000 (14:57 +0200)]
net/mlx5: Use offset based reserved field names in the IFC header file
mlx5_ifc.h is a header file representing the API and ABI between
the driver to the firmware and hardware. This file is used from
both the mlx5_ib and mlx5_core drivers.
Previously, this file used incrementing counter to indicate
reserved fields, for example:
If one developer implements through net-next feature A that uses
reserved_0, they replace it with featureA and renames reserved_1 to
reserved_0. In the same kernel cycle, a 2nd developer could implement
feature B through the rdma tree, that uses reserved_1 and split it to
featureB and a smaller reserved_1 field. This will cause a conflict
when the two trees are merged.
The source of this conflict is that the 1st developer changed *all*
reserved fields.
As Linus suggested, we change the layout of structs to:
Jay Vosburgh [Mon, 8 Feb 2016 20:10:02 +0000 (12:10 -0800)]
bonding: don't use stale speed and duplex information
There is presently a race condition between the bonding periodic
link monitor and the updating of a slave's speed and duplex. The former
occurs on a periodic basis, and the latter in response to a driver's
calling of netif_carrier_on.
It is possible for the periodic monitor to run between the
driver call of netif_carrier_on and the receipt of the NETDEV_CHANGE
event that causes bonding to update the slave's speed and duplex. This
manifests most notably as a report that a slave is up and "0 Mbps full
duplex" after enslavement, but in principle could report an incorrect
speed and duplex after any link up event if the device comes up with a
different speed or duplex. This affects the 802.3ad aggregator
selection, as the speed and duplex are selection criteria.
This is fixed by updating the speed and duplex in the periodic
monitor, prior to using that information.
This was done historically in bonding, but the call to
bond_update_speed_duplex was removed in commit 876254ae2758 ("bonding:
don't call update_speed_duplex() under spinlocks"), as it might sleep
under lock. Later, the locking was changed to only hold RTNL, and so
after commit 876254ae2758 ("bonding: don't call update_speed_duplex()
under spinlocks") this call is again safe.
Tested-by: "Tantilov, Emil S" <emil.s.tantilov@intel.com> Cc: Veaceslav Falico <vfalico@gmail.com> Cc: dingtianhong <dingtianhong@huawei.com> Fixes: 876254ae2758 ("bonding: don't call update_speed_duplex() under spinlocks") Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com> Acked-by: Ding Tianhong <dingtianhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The same change has been done a decade ago in arch/arm as of 6a39dd6222dd ("[ARM] 3759/2: Remove uses of %?"), but apparently
some drivers were missed.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Robert Jarzmik [Sat, 6 Feb 2016 21:23:20 +0000 (22:23 +0100)]
net: smc91x: propagate irq return code
The smc91x driver doesn't honor the probe deferral mechanism when the
interrupt source is not yet available, such as one provided by a gpio
controller not probed.
Fix this by propagating the platform_get_irq() error code as the probe
return value.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the two wildcard entries, they serve no purpose and will match way too
many devices, some of them being covered by the driver in
drivers/net/phy/broadcom.c. Remove the now unused bcm7xxx_dummy_config_init()
function which would produce a warning.
Fixes: b560a58c45c6 ("net: phy: add Broadcom BCM7xxx internal PHY driver") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Since we were wrongly advertising gigabit features for these 10/100 only
Ethernet PHYs, bcm7xxx_config_init() which is supposed to apply workaround
would have not run since the check would be true, now that we have fixed the
PHY features, remove that check since it has no reasoning to be there anymore.
Fixes: e18556ee3bd83 ("net: phy: bcm7xxx: do not use PHY_BRCM_100MBPS_WAR") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY entries for BCM7425/29/35 declare the 40nm Ethernet PHY as being
10/100/1000 capable, while this is just a 10/100 capable PHY device, fix that.
Fixes: d068b02cfdfc2 ("net: phy: add BCM7425 and BCM7429 PHYs") Fixes: 9458ceab4917 ("net: phy: bcm7xxx: Add entry for BCM7435") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The clear and set masks in the call to phy_set_clr_bits() called from
bcm7xxx_config_init() are inverted. We need to fix this by swapping the two
arguments, that is, set 0 bits, but clear the shade mode 2 enable bit.
Fixes: b560a58c45c66 ("net: phy: add Broadcom BCM7xxx internal PHY driver") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 16 Feb 2016 19:53:00 +0000 (14:53 -0500)]
Merge branch 'ravb-fixes'
Sergei Shtylyov says:
====================
ravb: fix the fallout of R-Car gen3 gPTP support
Here's a set of 2 patches against DaveM's 'net.git' repo fixing up the
incomplete commit f5d7837f96e5 ("ravb: ptp: Add CONFIG mode support").
I'm proposing these as fixes but they can be merged as cleanups as well...
[1/2] ravb: kill duplicate setting of CCC.CSEL
[2/2] ravb: skip gPTP start/stop on R-Car gen3
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Sergei Shtylyov [Sat, 6 Feb 2016 14:47:22 +0000 (17:47 +0300)]
ravb: skip gPTP start/stop on R-Car gen3
When adding support for the R-Car gen3 gPTP active in configuration mode,
some call sites of ravb_ptp_{init|stop}() were missed due to an oversight.
Add checks for the R-Car gen2 SoCs around these...
Fixes: f5d7837f96e5 ("ravb: ptp: Add CONFIG mode support") Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sergei Shtylyov [Sat, 6 Feb 2016 14:46:35 +0000 (17:46 +0300)]
ravb: kill duplicate setting of CCC.CSEL
When adding support for the R-Car gen3 gPTP active in configuration mode,
the code setting the CCC.CSEL field was duplicated due to an oversight.
For R-Car gen 2 it's just redundant and for R-Car gen3 the write at this
time is probably ignored due to CCC.GAC bit being already set...
Fixes: f5d7837f96e5 ("ravb: ptp: Add CONFIG mode support") Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The following patchset contain a rather large batch for your net that
includes accumulated bugfixes, they are:
1) Run conntrack cleanup from workqueue process context to avoid hitting
soft lockup via watchdog for large tables. This is required by the
IPv6 masquerading extension. From Florian Westphal.
2) Use original skbuff from nfnetlink batch when calling netlink_ack()
on error since this needs to access the skb->sk pointer.
3) Incremental fix on top of recent Sasha Levin's lock fix for conntrack
resizing.
4) Fix several problems in nfnetlink batch message header sanitization
and error handling, from Phil Turnbull.
5) Select NF_DUP_IPV6 based on CONFIG_IPV6, from Arnd Bergmann.
6) Fix wrong signess in return values on nf_tables counter expression,
from Anton Protopopov.
Due to the NetDev 1.1 organization burden, I had no chance to pass up
this to you any sooner in this release cycle, sorry about that.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Rainer Weikusat [Thu, 11 Feb 2016 19:37:27 +0000 (19:37 +0000)]
af_unix: Guard against other == sk in unix_dgram_sendmsg
The unix_dgram_sendmsg routine use the following test
if (unlikely(unix_peer(other) != sk && unix_recvq_full(other))) {
to determine if sk and other are in an n:1 association (either
established via connect or by using sendto to send messages to an
unrelated socket identified by address). This isn't correct as the
specified address could have been bound to the sending socket itself or
because this socket could have been connected to itself by the time of
the unix_peer_get but disconnected before the unix_state_lock(other). In
both cases, the if-block would be entered despite other == sk which
might either block the sender unintentionally or lead to trying to unlock
the same spin lock twice for a non-blocking send. Add a other != sk
check to guard against this.
Fixes: 7d267278a9ec ("unix: avoid use-after-free in ep_remove_wait_queue") Reported-By: Philipp Hahn <pmhahn@pmhahn.de> Signed-off-by: Rainer Weikusat <rweikusat@mobileactivedefense.com> Tested-by: Philipp Hahn <pmhahn@pmhahn.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Change it such that err is only set if an error condition was detected.
Fixes: 3822b5c2fc62 ("af_unix: Revert 'lock_interruptible' in stream receive code") Reported-by: Joseph Salisbury <joseph.salisbury@canonical.com> Signed-off-by: Rainer Weikusat <rweikusat@mobileactivedefense.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Thu, 11 Feb 2016 21:15:57 +0000 (22:15 +0100)]
batman-adv: Avoid endless loop in bat-on-bat netdevice check
batman-adv checks in different situation if a new device is already on top
of a different batman-adv device. This is done by getting the iflink of a
device and all its parent. It assumes that this iflink is always a parent
device in an acyclic graph. But this assumption is broken by devices like
veth which are actually a pair of two devices linked to each other. The
recursive check would therefore get veth0 when calling dev_get_iflink on
veth1. And it gets veth0 when calling dev_get_iflink with veth1.
Creating a veth pair and loading batman-adv freezes parts of the system
ip link add veth0 type veth peer name veth1
modprobe batman-adv
An RCU stall will be detected on the system which cannot be fixed.
This can be avoided by checking if two devices are each others parent and
stopping the check in this situation.
Fixes: b7eddd0b3950 ("batman-adv: prevent using any virtual device created on batman-adv as hard-interface") Signed-off-by: Andrew Lunn <andrew@lunn.ch>
[sven@narfation.org: rewritten description, extracted fix] Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <a@unstable.cc>
Sven Eckelmann [Sun, 31 Jan 2016 12:28:00 +0000 (13:28 +0100)]
batman-adv: Only put orig_node_vlan list reference when removed
The batadv_orig_node_vlan reference counter in batadv_tt_global_size_mod
can only be reduced when the list entry was actually removed. Otherwise the
reference counter may reach zero when batadv_tt_global_size_mod is called
from two different contexts for the same orig_node_vlan but only one
context is actually removing the entry from the list.
The release function for this orig_node_vlan is not called inside the
vlan_list_lock spinlock protected region because the function
batadv_tt_global_size_mod still holds a orig_node_vlan reference for the
object pointer on the stack. Thus the actual release function (when
required) will be called only at the end of the function.
Fixes: 7ea7b4a14275 ("batman-adv: make the TT CRC logic VLAN specific") Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <a@unstable.cc>
Sven Eckelmann [Sun, 31 Jan 2016 12:27:59 +0000 (13:27 +0100)]
batman-adv: Only put gw_node list reference when removed
The batadv_gw_node reference counter in batadv_gw_node_update can only be
reduced when the list entry was actually removed. Otherwise the reference
counter may reach zero when batadv_gw_node_update is called from two
different contexts for the same gw_node but only one context is actually
removing the entry from the list.
The release function for this gw_node is not called inside the list_lock
spinlock protected region because the function batadv_gw_node_update still
holds a gw_node reference for the object pointer on the stack. Thus the
actual release function (when required) will be called only at the end of
the function.
Fixes: bd3524c14bd0 ("batman-adv: remove obsolete deleted attribute for gateway node") Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Michael McConville <mmcco@mykolab.com> Acked-by: Francois Romieu <romieu@fr.zoreil.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Fri, 5 Feb 2016 19:07:14 +0000 (14:07 -0500)]
net: dsa: mv88e6xxx: do not leave reserved VLANs
BRIDGE_VLAN_FILTERING automatically adds a newly bridged port to the
VLAN with the bridge's default_pvid.
The mv88e6xxx driver currently reserves VLANs 4000+ for unbridged ports
isolation. When a port joins a bridge, it leaves its reserved VLAN. When
a port leaves a bridge, it joins again its reserved VLAN.
But if the VLAN filtering is disabled, or if this hardware VLAN is
already in use, the bridged port ends up with no default VLAN, and the
communication with the CPU is thus broken.
To fix this, make a port join its reserved VLAN once on setup, never
leave it, and restore its PVID after another one was eventually used.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Tested-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Fri, 5 Feb 2016 19:04:39 +0000 (14:04 -0500)]
net: dsa: mv88e6xxx: fix software VLAN deletion
The current bridge code calls switchdev_port_obj_del on a VLAN port even
if the corresponding switchdev_port_obj_add call returned -EOPNOTSUPP.
If the DSA driver doesn't return -EOPNOTSUPP for a software port VLAN in
its port_vlan_del function, the VLAN is not deleted. Unbridging the port
also generates a stack trace for the same reason.
This can be quickly tested on a VLAN filtering enabled system with:
To fix this, return -EOPNOTSUPP in _mv88e6xxx_port_vlan_del instead of
-ENOENT if the hardware VLAN doesn't exist or the port is not a member.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Tested-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Commit c0eb454034aa ("hv_netvsc: Don't ask for additional head room in the
skb") got rid of needed_headroom setting for the driver. With the change I
hit the following issue trying to use ptkgen module:
Basically, we're calling skb_cow_head(skb, RNDIS_AND_PPI_SIZE) and crash on
if (skb_shared(skb))
BUG();
We probably need to restore needed_headroom setting (but shrunk to
RNDIS_AND_PPI_SIZE as we don't need more) to request the required headroom
space. In theory, it should not give us performance penalty.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 13 Feb 2016 11:02:25 +0000 (06:02 -0500)]
Merge branch 'mvneta-fixes'
Gregory CLEMENT says:
====================
mvneta fixes for SMP
Following this bug report:
http://thread.gmane.org/gmane.linux.ports.arm.kernel/468173 and the
suggestions from Russell King, I reviewed all the code involving
multi-CPU. It ended with this series of patches which should improve
the stability of the driver.
During my test I found another bug which is fixed by new patch (the
second one of this new version of the series)
The two first patches fix real bugs, the others fix potential issues
in the driver.
Changelog:
v1 -> v2
Fix spinlock comment. Pointed by David Miller
v2 -> v3
- Fix typos and mistake in the comments. Pointed by Sergei Shtylyov
- Add a new patch fixing the CPU choice in mvneta_percpu_elect
- Use lock in last patch to prevent remaining race condition. Pointed
by Jisheng
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Gregory CLEMENT [Thu, 4 Feb 2016 21:09:29 +0000 (22:09 +0100)]
net: mvneta: Fix race condition during stopping
When stopping the port, the CPU notifier are still there whereas the
mvneta_stop_dev function calls mvneta_percpu_disable() on each CPUs.
It was possible to have a new CPU coming at this point which could be
racy.
This patch adds a flag preventing executing the code notifier for a new
CPU when the port is stopping. It also uses the spinlock introduces
previously. To avoid the deadlock, the lock has been moved outside the
mvneta_percpu_elect function.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Gregory CLEMENT [Thu, 4 Feb 2016 21:09:28 +0000 (22:09 +0100)]
net: mvneta: The mvneta_percpu_elect function should be atomic
Electing a CPU must be done in an atomic way: it should be done after or
before the removal/insertion of a CPU and this function is not reentrant.
During the loop of mvneta_percpu_elect we associates the queues to the
CPUs, if there is a topology change during this loop, then the mapping
between the CPUs and the queues could be wrong. During this loop the
interrupt mask is also updating for each CPUs, It should not be changed
in the same time by other part of the driver.
This patch adds spinlock to create the needed critical sections.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Gregory CLEMENT [Thu, 4 Feb 2016 21:09:27 +0000 (22:09 +0100)]
net: mvneta: Modify the queue related fields from each cpu
In the MVNETA_INTR_* registers, the queues related fields are per cpu,
according to the datasheet (comment in [] are added by me):
"In a multi-CPU system, bits of RX[or TX] queues for which the access by
the reading[or writing] CPU is disabled are read as 0, and cannot be
cleared[or written]."
That means that each time we want to manipulate these bits we had to do
it on each cpu and not only on the current cpu.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Gregory CLEMENT [Thu, 4 Feb 2016 21:09:26 +0000 (22:09 +0100)]
net: mvneta: Remove unused code
Since the commit 2dcf75e2793c ("net: mvneta: Associate RX queues with
each CPU") all the percpu irq are used and disabled at initialization, so
there is no point to disable them first.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Gregory CLEMENT [Thu, 4 Feb 2016 21:09:25 +0000 (22:09 +0100)]
net: mvneta: Use on_each_cpu when possible
Instead of using a for_each_* loop in which we just call the
smp_call_function_single macro, it is more simple to directly use the
on_each_cpu macro. Moreover, this macro ensures that the calls will be
done all at once.
Suggested-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Gregory CLEMENT [Thu, 4 Feb 2016 21:09:24 +0000 (22:09 +0100)]
net: mvneta: Fix the CPU choice in mvneta_percpu_elect
When passing to the management of multiple RX queue, the
mvneta_percpu_elect function was broken. The use of the modulo can lead
to elect the wrong cpu. For example with rxq_def=2, if the CPU 2 goes
offline and then online, we ended with the third RX queue activated in
the same time on CPU 0 and CPU2, which lead to a kernel crash.
With this fix, we don't try to get "the closer" CPU if the default CPU is
gone, now we just use CPU 0 which always be there. Thanks to this, the
code becomes more readable, easier to maintain and more predicable.
Cc: stable@vger.kernel.org Fixes: 2dcf75e2793c ("net: mvneta: Associate RX queues with each CPU") Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Gregory CLEMENT [Thu, 4 Feb 2016 21:09:23 +0000 (22:09 +0100)]
net: mvneta: Fix for_each_present_cpu usage
This patch convert the for_each_present in on_each_cpu, instead of
applying on the present cpus it will be applied only on the online cpus.
This fix a bug reported on
http://thread.gmane.org/gmane.linux.ports.arm.kernel/468173.
Using the macro on_each_cpu (instead of a for_each_* loop) also ensures
that all the calls will be done all at once.
Fixes: f86428854480 ("net: mvneta: Statically assign queues to CPUs") Reported-by: Stefan Roese <stefan.roese@gmail.com> Suggested-by: Jisheng Zhang <jszhang@marvell.com> Suggested-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: David S. Miller <davem@davemloft.net>
transport->stream_enqueue may call copy_to_user so it should
not be called inside a prepare_to_wait. Narrow the scope of
the prepare_to_wait to avoid the bad call. This also applies
to vsock_stream_recvmsg as well.
Reported-by: Vinson Lee <vlee@freedesktop.org> Tested-by: Vinson Lee <vlee@freedesktop.org> Signed-off-by: Laura Abbott <labbott@fedoraproject.org> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / mirror_ubuntu-jammy-kernel.git / log