1) Fix refcount leak in act_ipt during replace, from Davide Caratti.
2) Set task state properly in tun during blocking reads, from Timur
Celik.
3) Leaked reference in DSA, from Wen Yang.
4) NULL deref in act_tunnel_key, from Vlad Buslov.
5) cipso_v4_erro can reference the skb IPCB in inappropriate contexts
thus referencing garbage, from Nazarov Sergey.
6) Don't accept RTA_VIA and RTA_GATEWAY in contexts where those
attributes make no sense.
7) Fix hung sendto in tipc, from Tung Nguyen.
8) Out-of-bounds access in netlabel, from Paul Moore.
9) Grant reference leak in xen-netback, from Igor Druzhinin.
10) Fix tx stalls with lan743x, from Bryan Whitehead.
11) Fix interrupt storm with mv88e6xxx, from Hein Kallweit.
12) Memory leak in sit on device registry failure, from Mao Wenan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (44 commits)
net: sit: fix memory leak in sit_init_net()
net: dsa: mv88e6xxx: Fix statistics on mv88e6161
geneve: correctly handle ipv6.disable module parameter
net: dsa: mv88e6xxx: prevent interrupt storm caused by mv88e6390x_port_set_cmode
bpf: fix sanitation rewrite in case of non-pointers
ipv4: Add ICMPv6 support when parse route ipproto
MIPS: eBPF: Fix icache flush end address
lan743x: Fix TX Stall Issue
net: phy: phylink: fix uninitialized variable in phylink_get_mac_state
net: aquantia: regression on cpus with high cores: set mode with 8 queues
selftests: fixes for UDP GRO
bpf: drop refcount if bpf_map_new_fd() fails in map_create()
net: dsa: mv88e6xxx: power serdes on/off for 10G interfaces on 6390X
net: dsa: mv88e6xxx: Fix u64 statistics
xen-netback: don't populate the hash cache on XenBus disconnect
xen-netback: fix occasional leak of grant ref mappings under memory pressure
sctp: chunk.c: correct format string for size_t in printk
net: netem: fix skb length BUG_ON in __skb_to_sgvec
netlabel: fix out-of-bounds memory accesses
ipv4: Pass original device to ip_rcv_finish_core
...
Linus Torvalds [Sat, 2 Mar 2019 16:32:02 +0000 (08:32 -0800)]
Merge branch 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull more crypto fixes from Herbert Xu:
"This fixes a couple of issues in arm64/chacha that was introduced in
5.0"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: arm64/chacha - fix hchacha_block_neon() for big endian
crypto: arm64/chacha - fix chacha_4block_xor_neon() for big endian
When IPv6 is compiled but disabled at runtime, geneve_sock_add returns
-EAFNOSUPPORT. For metadata based tunnels, this causes failure of the whole
operation of bringing up the tunnel.
Ignore failure of IPv6 socket creation for metadata based tunnels caused by
IPv6 not being available.
This is the same fix as what commit d074bf960044 ("vxlan: correctly handle
ipv6.disable module parameter") is doing for vxlan.
Note there's also commit c0a47e44c098 ("geneve: should not call rt6_lookup()
when ipv6 was disabled") which fixes a similar issue but for regular
tunnels, while this patch is needed for metadata based tunnels.
Signed-off-by: Jiri Benc <jbenc@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Thu, 28 Feb 2019 06:39:15 +0000 (07:39 +0100)]
net: dsa: mv88e6xxx: prevent interrupt storm caused by mv88e6390x_port_set_cmode
When debugging another issue I faced an interrupt storm in this
driver (88E6390, port 9 in SGMII mode), consisting of alternating
link-up / link-down interrupts. Analysis showed that the driver
wanted to set a cmode that was set already. But so far
mv88e6390x_port_set_cmode() doesn't check this and powers down
SERDES, what causes the link to break, and eventually results in
the described interrupt storm.
Fix this by checking whether the cmode actually changes. We want
that the very first call to mv88e6390x_port_set_cmode() always
configures the registers, therefore initialize port.cmode with
a value that is different from any supported cmode value.
We have to take care that we only init the ports cmode once
chip->info->num_ports is set.
v2:
- add small helper and init the number of actual ports only
Fixes: 364e9d7776a3 ("net: dsa: mv88e6xxx: Power on/off SERDES on cmode change") Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Fri, 1 Mar 2019 21:05:29 +0000 (22:05 +0100)]
bpf: fix sanitation rewrite in case of non-pointers
Marek reported that he saw an issue with the below snippet in that
timing measurements where off when loaded as unpriv while results
were reasonable when loaded as privileged:
[...]
uint64_t a = bpf_ktime_get_ns();
uint64_t b = bpf_ktime_get_ns();
uint64_t delta = b - a;
if ((int64_t)delta > 0) {
[...]
Turns out there is a bug where a corner case is missing in the fix d3bd7413e0ca ("bpf: fix sanitation of alu op with pointer / scalar
type from different paths"), namely fixup_bpf_calls() only checks
whether aux has a non-zero alu_state, but it also needs to test for
the case of BPF_ALU_NON_POINTER since in both occasions we need to
skip the masking rewrite (as there is nothing to mask).
Fixes: d3bd7413e0ca ("bpf: fix sanitation of alu op with pointer / scalar type from different paths") Reported-by: Marek Majkowski <marek@cloudflare.com> Reported-by: Arthur Fabre <afabre@cloudflare.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/netdev/CAJPywTJqP34cK20iLM5YmUMz9KXQOdu1-+BZrGMAGgLuBWz7fg@mail.gmail.com/T/ Acked-by: Song Liu <songliubraving@fb.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Hangbin Liu [Wed, 27 Feb 2019 08:15:29 +0000 (16:15 +0800)]
ipv4: Add ICMPv6 support when parse route ipproto
For ip rules, we need to use 'ipproto ipv6-icmp' to match ICMPv6 headers.
But for ip -6 route, currently we only support tcp, udp and icmp.
Add ICMPv6 support so we can match ipv6-icmp rules for route lookup.
v2: As David Ahern and Sabrina Dubroca suggested, Add an argument to
rtm_getroute_parse_ip_proto() to handle ICMP/ICMPv6 with different family.
Reported-by: Jianlin Shi <jishi@redhat.com> Fixes: eacb9384a3fe ("ipv6: support sport, dport and ip_proto in RTM_GETROUTE") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Burton [Fri, 1 Mar 2019 22:58:09 +0000 (22:58 +0000)]
MIPS: eBPF: Fix icache flush end address
The MIPS eBPF JIT calls flush_icache_range() in order to ensure the
icache observes the code that we just wrote. Unfortunately it gets the
end address calculation wrong due to some bad pointer arithmetic.
The struct jit_ctx target field is of type pointer to u32, and as such
adding one to it will increment the address being pointed to by 4 bytes.
Therefore in order to find the address of the end of the code we simply
need to add the number of 4 byte instructions emitted, but we mistakenly
add the number of instructions multiplied by 4. This results in the call
to flush_icache_range() operating on a memory region 4x larger than
intended, which is always wasteful and can cause crashes if we overrun
into an unmapped page.
Fix this by correcting the pointer arithmetic to remove the bogus
multiplication, and use braces to remove the need for a set of brackets
whilst also making it obvious that the target field is a pointer.
Signed-off-by: Paul Burton <paul.burton@mips.com> Fixes: b6bd53f9c4e8 ("MIPS: Add missing file for eBPF JIT.") Cc: Alexei Starovoitov <ast@kernel.org> Cc: Daniel Borkmann <daniel@iogearbox.net> Cc: Martin KaFai Lau <kafai@fb.com> Cc: Song Liu <songliubraving@fb.com> Cc: Yonghong Song <yhs@fb.com> Cc: netdev@vger.kernel.org Cc: bpf@vger.kernel.org Cc: linux-mips@vger.kernel.org Cc: stable@vger.kernel.org # v4.13+ Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Bryan Whitehead [Tue, 26 Feb 2019 19:06:26 +0000 (14:06 -0500)]
lan743x: Fix TX Stall Issue
It has been observed that tx queue stalls while downloading
from certain web sites (example www.speedtest.net)
The cause has been tracked down to a corner case where
dma descriptors where not setup properly. And there for a tx
completion interrupt was not signaled.
This fix corrects the problem by properly marking the end of
a multi descriptor transmission.
Fixes: 23f0703c125b ("lan743x: Add main source files for new lan743x driver") Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Tue, 26 Feb 2019 18:29:22 +0000 (19:29 +0100)]
net: phy: phylink: fix uninitialized variable in phylink_get_mac_state
When debugging an issue I found implausible values in state->pause.
Reason in that state->pause isn't initialized and later only single
bits are changed. Also the struct itself isn't initialized in
phylink_resolve(). So better initialize state->pause and other
not yet initialized fields.
v2:
- use right function name in subject
v3:
- initialize additional fields
Fixes: 9525ae83959b ("phylink: add phylink infrastructure") Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Bogdanov [Tue, 26 Feb 2019 15:39:13 +0000 (15:39 +0000)]
net: aquantia: regression on cpus with high cores: set mode with 8 queues
Recently the maximum number of queues was increased up to 8, but
NIC was not fully configured for 8 queues. In setups with more than 4 CPU
cores parts of TX traffic gets lost if the kernel routes it to queues 4th-8th.
This patch sets a tx hw traffic mode with 8 queues.
Fixes: 71a963cfc50b ("net: aquantia: increase max number of hw queues") Reported-by: Nicholas Johnson <nicholas.johnson@outlook.com.au> Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com> Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Tue, 26 Feb 2019 14:27:43 +0000 (15:27 +0100)]
selftests: fixes for UDP GRO
The current implementation for UDP GRO tests is racy: the receiver
may flush the RX queue while the sending is still transmitting and
incorrectly report RX errors, with a wrong number of packet received.
Add explicit timeouts to the receiver for both connection activation
(first packet received for UDP) and reception completion, so that
in the above critical scenario the receiver will wait for the
transfer completion.
Fixes: 3327a9c46352 ("selftests: add functionals test for UDP GRO") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Acked-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 1 Mar 2019 17:13:04 +0000 (09:13 -0800)]
Merge tag 'iommu-fix-v5.0-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fix from Joerg Roedel:
"One important fix for a memory corruption issue in the Intel VT-d
driver that triggers on hardware with deep PCI hierarchies"
* tag 'iommu-fix-v5.0-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/dmar: Fix buffer overflow during PCI bus notification
Linus Torvalds [Fri, 1 Mar 2019 17:04:59 +0000 (09:04 -0800)]
Merge branch 'akpm' (patches from Andrew)
Merge misc fixes from Andrew Morton:
"2 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
hugetlbfs: fix races and page leaks during migration
kasan: turn off asan-stack for clang-8 and earlier
Mike Kravetz [Fri, 1 Mar 2019 00:22:02 +0000 (16:22 -0800)]
hugetlbfs: fix races and page leaks during migration
hugetlb pages should only be migrated if they are 'active'. The
routines set/clear_page_huge_active() modify the active state of hugetlb
pages.
When a new hugetlb page is allocated at fault time, set_page_huge_active
is called before the page is locked. Therefore, another thread could
race and migrate the page while it is being added to page table by the
fault code. This race is somewhat hard to trigger, but can be seen by
strategically adding udelay to simulate worst case scheduling behavior.
Depending on 'how' the code races, various BUG()s could be triggered.
To address this issue, simply delay the set_page_huge_active call until
after the page is successfully added to the page table.
Hugetlb pages can also be leaked at migration time if the pages are
associated with a file in an explicitly mounted hugetlbfs filesystem.
For example, consider a two node system with 4GB worth of huge pages
available. A program mmaps a 2G file in a hugetlbfs filesystem. It
then migrates the pages associated with the file from one node to
another. When the program exits, huge page counts are as follows:
node0
1024 free_hugepages
1024 nr_hugepages
node1
0 free_hugepages
1024 nr_hugepages
Filesystem Size Used Avail Use% Mounted on
nodev 4.0G 2.0G 2.0G 50% /var/opt/hugepool
That is as expected. 2G of huge pages are taken from the free_hugepages
counts, and 2G is the size of the file in the explicitly mounted
filesystem. If the file is then removed, the counts become:
node0
1024 free_hugepages
1024 nr_hugepages
node1
1024 free_hugepages
1024 nr_hugepages
Filesystem Size Used Avail Use% Mounted on
nodev 4.0G 2.0G 2.0G 50% /var/opt/hugepool
Note that the filesystem still shows 2G of pages used, while there
actually are no huge pages in use. The only way to 'fix' the filesystem
accounting is to unmount the filesystem
If a hugetlb page is associated with an explicitly mounted filesystem,
this information in contained in the page_private field. At migration
time, this information is not preserved. To fix, simply transfer
page_private from old to new page at migration time if necessary.
There is a related race with removing a huge page from a file and
migration. When a huge page is removed from the pagecache, the
page_mapping() field is cleared, yet page_private remains set until the
page is actually freed by free_huge_page(). A page could be migrated
while in this state. However, since page_mapping() is not set the
hugetlbfs specific routine to transfer page_private is not called and we
leak the page count in the filesystem.
To fix that, check for this condition before migrating a huge page. If
the condition is detected, return EBUSY for the page.
Arnd Bergmann [Fri, 1 Mar 2019 00:21:58 +0000 (16:21 -0800)]
kasan: turn off asan-stack for clang-8 and earlier
Building an arm64 allmodconfig kernel with clang results in over 140
warnings about overly large stack frames, the worst ones being:
drivers/gpu/drm/panel/panel-sitronix-st7789v.c:196:12: error: stack frame size of 20224 bytes in function 'st7789v_prepare'
drivers/video/fbdev/omap2/omapfb/displays/panel-tpo-td028ttec1.c:196:12: error: stack frame size of 13120 bytes in function 'td028ttec1_panel_enable'
drivers/usb/host/max3421-hcd.c:1395:1: error: stack frame size of 10048 bytes in function 'max3421_spi_thread'
drivers/net/wan/slic_ds26522.c:209:12: error: stack frame size of 9664 bytes in function 'slic_ds26522_probe'
drivers/crypto/ccp/ccp-ops.c:2434:5: error: stack frame size of 8832 bytes in function 'ccp_run_cmd'
drivers/media/dvb-frontends/stv0367.c:1005:12: error: stack frame size of 7840 bytes in function 'stv0367ter_algo'
None of these happen with gcc today, and almost all of these are the
result of a single known issue in llvm. Hopefully it will eventually
get fixed with the clang-9 release.
In the meantime, the best idea I have is to turn off asan-stack for
clang-8 and earlier, so we can produce a kernel that is safe to run.
I have posted three patches that address the frame overflow warnings
that are not addressed by turning off asan-stack, so in combination with
this change, we get much closer to a clean allmodconfig build, which in
turn is necessary to do meaningful build regression testing.
It is still possible to turn on the CONFIG_ASAN_STACK option on all
versions of clang, and it's always enabled for gcc, but when
CONFIG_COMPILE_TEST is set, the option remains invisible, so
allmodconfig and randconfig builds (which are normally done with a
forced CONFIG_COMPILE_TEST) will still result in a mostly clean build.
Link: http://lkml.kernel.org/r/20190222222950.3997333-1-arnd@arndb.de Link: https://bugs.llvm.org/show_bug.cgi?id=38809 Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Qian Cai <cai@lca.pw> Reviewed-by: Mark Brown <broonie@kernel.org> Acked-by: Andrey Ryabinin <aryabinin@virtuozzo.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Nick Desaulniers <ndesaulniers@google.com> Cc: Kostya Serebryany <kcc@google.com> Cc: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 1 Mar 2019 16:44:11 +0000 (08:44 -0800)]
Merge tag 'drm-fixes-2019-03-01' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Three final fixes, one for a feature that is new in this kernel, one
bochs fix for qemu riscv and one atomic modesetting fix.
I've left a few of the other late fixes until next as I didn't want to
throw in anything that wasn't really necessary"
* tag 'drm-fixes-2019-03-01' of git://anongit.freedesktop.org/drm/drm:
drm/bochs: Fix the ID mismatch error
drm: Block fb changes for async plane updates
drm/amd/display: Use vrr friendly pageflip throttling in DC.
Peng Sun [Wed, 27 Feb 2019 14:36:25 +0000 (22:36 +0800)]
bpf: drop refcount if bpf_map_new_fd() fails in map_create()
In bpf/syscall.c, map_create() first set map->usercnt to 1, a file
descriptor is supposed to return to userspace. When bpf_map_new_fd()
fails, drop the refcount.
Fixes: bd5f5f4ecb78 ("bpf: Add BPF_MAP_GET_FD_BY_ID") Signed-off-by: Peng Sun <sironhide0null@gmail.com> Acked-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Linus Torvalds [Thu, 28 Feb 2019 23:33:10 +0000 (15:33 -0800)]
Merge tag 'mips_fixes_5.0_4' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS fixes from Paul Burton:
"A few more MIPS fixes:
- Fix 16b cmpxchg() operations which could erroneously fail if bits
15:8 of the old value are non-zero. In practice I'm not aware of
any actual users of 16b cmpxchg() on MIPS, but this fixes the
support for it was was introduced in v4.13.
- Provide a struct device to dma_alloc_coherent for Lantiq XWAY
systems with a "Voice MIPS Macro Core" (VMMC) device.
- Provide DMA masks for BCM63xx ethernet devices, fixing a regression
introduced in v4.19.
- Fix memblock reservation for the kernel when the system has a
non-zero PHYS_OFFSET, correcting the memblock conversion performed
in v4.20"
* tag 'mips_fixes_5.0_4' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MIPS: fix memory setup for platforms with PHYS_OFFSET != 0
MIPS: BCM63XX: provide DMA masks for ethernet devices
MIPS: lantiq: pass struct device to DMA API functions
MIPS: fix truncation in __cmpxchg_small for short values
net: dsa: mv88e6xxx: power serdes on/off for 10G interfaces on 6390X
Upon setting the cmode on 6390 and 6390X, the associated serdes
interfaces must be powered off/on.
Both 6390X and 6390 share code to do so, but it currently uses the 6390
specific helper mv88e6390_serdes_power() to disable and enable the
serdes interface.
This call will fail silently on 6390X when trying so set a 10G interface
such as XAUI or RXAUI, since mv88e6390_serdes_power() internally grabs
the lane number based on modes supported by the 6390, and returns 0 when
getting -ENODEV as a lane number.
Using mv88e6390x_serdes_power() should be safe here, since we explicitly
rule-out all ports but the 9 and 10, and because modes supported by 6390
ports 9 and 10 are a subset of those supported on 6390X.
This was tested on 6390X using RXAUI mode.
Fixes: 364e9d7776a3 ("net: dsa: mv88e6xxx: Power on/off SERDES on cmode change") Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Thu, 28 Feb 2019 17:14:03 +0000 (18:14 +0100)]
net: dsa: mv88e6xxx: Fix u64 statistics
The switch maintains u64 counters for the number of octets sent and
received. These are kept as two u32's which need to be combined. Fix
the combing, which wrongly worked on u16's.
Fixes: 80c4627b2719 ("dsa: mv88x6xxx: Refactor getting a single statistic") Reported-by: Chris Healy <Chris.Healy@zii.aero> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Igor Druzhinin [Thu, 28 Feb 2019 14:11:26 +0000 (14:11 +0000)]
xen-netback: don't populate the hash cache on XenBus disconnect
Occasionally, during the disconnection procedure on XenBus which
includes hash cache deinitialization there might be some packets
still in-flight on other processors. Handling of these packets includes
hashing and hash cache population that finally results in hash cache
data structure corruption.
In order to avoid this we prevent hashing of those packets if there
are no queues initialized. In that case RCU protection of queues guards
the hash cache as well.
Signed-off-by: Igor Druzhinin <igor.druzhinin@citrix.com> Reviewed-by: Paul Durrant <paul.durrant@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Igor Druzhinin [Thu, 28 Feb 2019 12:48:03 +0000 (12:48 +0000)]
xen-netback: fix occasional leak of grant ref mappings under memory pressure
Zero-copy callback flag is not yet set on frag list skb at the moment
xenvif_handle_frag_list() returns -ENOMEM. This eventually results in
leaking grant ref mappings since xenvif_zerocopy_callback() is never
called for these fragments. Those eventually build up and cause Xen
to kill Dom0 as the slots get reused for new mappings:
"d0v0 Attempt to implicitly unmap a granted PTE c010000329fce005"
That behavior is observed under certain workloads where sudden spikes
of page cache writes coexist with active atomic skb allocations from
network traffic. Additionally, rework the logic to deal with frag_list
deallocation in a single place.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com> Signed-off-by: Igor Druzhinin <igor.druzhinin@citrix.com> Acked-by: Wei Liu <wei.liu2@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
sctp: chunk.c: correct format string for size_t in printk
According to Documentation/core-api/printk-formats.rst, size_t should be
printed with %zu, rather than %Zu.
In addition, using %Zu triggers a warning on clang (-Wformat-extra-args):
net/sctp/chunk.c:196:25: warning: data argument not used by format string [-Wformat-extra-args]
__func__, asoc, max_data);
~~~~~~~~~~~~~~~~^~~~~~~~~
./include/linux/printk.h:440:49: note: expanded from macro 'pr_warn_ratelimited'
printk_ratelimited(KERN_WARNING pr_fmt(fmt), ##__VA_ARGS__)
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~
./include/linux/printk.h:424:17: note: expanded from macro 'printk_ratelimited'
printk(fmt, ##__VA_ARGS__); \
~~~ ^
Fixes: 5b5e0928f742 ("lib/vsprintf.c: remove %Z support") Link: https://github.com/ClangBuiltLinux/linux/issues/378 Signed-off-by: Matthias Maennich <maennich@google.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sheng Lan [Thu, 28 Feb 2019 10:47:58 +0000 (18:47 +0800)]
net: netem: fix skb length BUG_ON in __skb_to_sgvec
It can be reproduced by following steps:
1. virtio_net NIC is configured with gso/tso on
2. configure nginx as http server with an index file bigger than 1M bytes
3. use tc netem to produce duplicate packets and delay:
tc qdisc add dev eth0 root netem delay 100ms 10ms 30% duplicate 90%
4. continually curl the nginx http server to get index file on client
5. BUG_ON is seen quickly
In __skb_to_sgvec(), the skb->len is not equal to the sum of the skb's
linear data size and nonlinear data size, thus BUG_ON triggered.
Because the skb is cloned and a part of nonlinear data is split off.
Duplicate packet is cloned in netem_enqueue() and may be delayed
some time in qdisc. When qdisc len reached the limit and returns
NET_XMIT_DROP, the skb will be retransmit later in write queue.
the skb will be fragmented by tso_fragment(), the limit size
that depends on cwnd and mss decrease, the skb's nonlinear
data will be split off. The length of the skb cloned by netem
will not be updated. When we use virtio_net NIC and invoke skb_to_sgvec(),
the BUG_ON trigger.
To fix it, netem returns NET_XMIT_SUCCESS to upper stack
when it clones a duplicate packet.
Fixes: 35d889d1 ("sch_netem: fix skb leak in netem_enqueue()") Signed-off-by: Sheng Lan <lansheng@huawei.com> Reported-by: Qin Ji <jiqin.ji@huawei.com> Suggested-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 28 Feb 2019 17:18:07 +0000 (09:18 -0800)]
Merge tag 'mmc-v5.0-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"MMC core:
- Fix NULL ptr crash for a special test case
- Align max segment size with logical block size to prevent bugs in
v5.1-rc1.
MMC host:
- cqhci: Minor fixes
- tmio: Prevent interrupt storm
- tmio: Fixup SD/MMC card initialization
- spi: Allow card to be detected during probe
- sdhci-esdhc-imx: Fixup fix for ERR004536"
* tag 'mmc-v5.0-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: sdhci-esdhc-imx: correct the fix of ERR004536
mmc: core: align max segment size with logical block size
mmc: cqhci: Fix a tiny potential memory leak on error condition
mmc: cqhci: fix space allocated for transfer descriptor
mmc: core: Fix NULL ptr crash from mmc_should_fail_request
mmc: tmio: fix access width of Block Count Register
mmc: tmio_mmc_core: don't claim spurious interrupts
mmc: spi: Fix card detection during probe
kvm: properly check debugfs dentry before using it
debugfs can now report an error code if something went wrong instead of
just NULL. So if the return value is to be used as a "real" dentry, it
needs to be checked if it is an error before dereferencing it.
This is now happening because of ff9fb72bc077 ("debugfs: return error
values, not NULL"). syzbot has found a way to trigger multiple debugfs
files attempting to be created, which fails, and then the error code
gets passed to dentry_path_raw() which obviously does not like it.
BOUGH CHEN [Thu, 28 Feb 2019 10:15:42 +0000 (10:15 +0000)]
mmc: sdhci-esdhc-imx: correct the fix of ERR004536
Commit 18094430d6b5 ("mmc: sdhci-esdhc-imx: add ADMA Length
Mismatch errata fix") involve the fix of ERR004536, but the
fix is incorrect. Double confirm with IC, need to clear the
bit 7 of register 0x6c rather than set this bit 7.
Here is the definition of bit 7 of 0x6c:
0: enable the new IC fix for ERR004536
1: do not use the IC fix, keep the same as before
Find this issue on i.MX845s-evk board when enable CMDQ, and
let system in heavy loading.
Eric Biggers [Sat, 23 Feb 2019 06:54:08 +0000 (22:54 -0800)]
crypto: arm64/chacha - fix hchacha_block_neon() for big endian
On big endian arm64 kernels, the xchacha20-neon and xchacha12-neon
self-tests fail because hchacha_block_neon() outputs little endian words
but the C code expects native endianness. Fix it to output the words in
native endianness (which also makes it match the arm32 version).
Fixes: cc7cf991e9eb ("crypto: arm64/chacha20 - add XChaCha20 support") Signed-off-by: Eric Biggers <ebiggers@google.com> Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Eric Biggers [Sat, 23 Feb 2019 06:54:07 +0000 (22:54 -0800)]
crypto: arm64/chacha - fix chacha_4block_xor_neon() for big endian
The change to encrypt a fifth ChaCha block using scalar instructions
caused the chacha20-neon, xchacha20-neon, and xchacha12-neon self-tests
to start failing on big endian arm64 kernels. The bug is that the
keystream block produced in 32-bit scalar registers is directly XOR'd
with the data words, which are loaded and stored in native endianness.
Thus in big endian mode the data bytes end up XOR'd with the wrong
bytes. Fix it by byte-swapping the keystream words in big endian mode.
Fixes: 2fe55987b262 ("crypto: arm64/chacha - use combined SIMD/ALU routine for more speed") Signed-off-by: Eric Biggers <ebiggers@google.com> Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Paul Moore [Tue, 26 Feb 2019 00:06:06 +0000 (19:06 -0500)]
netlabel: fix out-of-bounds memory accesses
There are two array out-of-bounds memory accesses, one in
cipso_v4_map_lvl_valid(), the other in netlbl_bitmap_walk(). Both
errors are embarassingly simple, and the fixes are straightforward.
As a FYI for anyone backporting this patch to kernels prior to v4.8,
you'll want to apply the netlbl_bitmap_walk() patch to
cipso_v4_bitmap_walk() as netlbl_bitmap_walk() doesn't exist before
Linux v4.8.
Reported-by: Jann Horn <jannh@google.com> Fixes: 446fda4f2682 ("[NetLabel]: CIPSOv4 engine") Fixes: 3faa8f982f95 ("netlabel: Move bitmap manipulation functions to the NetLabel core.") Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Mon, 25 Feb 2019 21:55:48 +0000 (13:55 -0800)]
ipv4: Pass original device to ip_rcv_finish_core
ip_route_input_rcu expects the original ingress device (e.g., for
proper multicast handling). The skb->dev can be changed by l3mdev_ip_rcv,
so dev needs to be saved prior to calling it. This was the behavior prior
to the listify changes.
Fixes: 5fa12739a53d0 ("net: ipv4: listify ip_rcv_finish") Cc: Edward Cree <ecree@solarflare.com> Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 28 Feb 2019 05:28:59 +0000 (21:28 -0800)]
Merge branch 'pmtu-selftest-fixes'
Paolo Abeni says:
====================
selftests: pmtu: fix and increase coverage
This series includes a fixup for the pmtu.sh test script, related to IPv6
address management, and adds coverage for the recently reported and fixed
PMTU exception issue
v2 -> v3:
- more cleanups
v1 -> v2:
- several script cleanups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Mon, 25 Feb 2019 15:08:37 +0000 (16:08 +0100)]
selftests: pmtu: add explicit tests for PMTU exceptions cleanup
Add a couple of new tests, explicitly checking that the kernel
timely releases PMTU exceptions on related device removal.
This is mostly a regression test vs the issue fixed by
commit f5b51fe804ec ("ipv6: route: purge exception on removal")
Only 2 new test cases have been added, instead of extending all
the existing ones, because the reproducer requires executing
several commands and would slow down too much the tests otherwise.
v2 -> v3:
- more cleanup, still from Stefano
v1 -> v2:
- several script cleanups, as suggested by Stefano
Signed-off-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Mon, 25 Feb 2019 15:08:36 +0000 (16:08 +0100)]
selftests: pmtu: disable DAD in all namespaces
Otherwise, the configured IPv6 address could be still "tentative"
at test time, possibly causing tests failures.
We can also drop some sleep along the code and decrease the
timeout for most commands so that the test runtime decreases.
v1 -> v2:
- fix comment (Stefano)
Fixes: d1f1b9cbf34c ("selftests: net: Introduce first PMTU test") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The prepare_fb call always happens on new_plane_state.
The drm_atomic_helper_cleanup_planes checks to see if
plane state pointer has changed when deciding to call cleanup_fb on
either the new_plane_state or the old_plane_state.
For a non-async atomic commit the state pointer is swapped, so this
helper calls prepare_fb on the new_plane_state and cleanup_fb on the
old_plane_state. This makes sense, since we want to prepare the
framebuffer we are going to use and cleanup the the framebuffer we are
no longer using.
For the async atomic update helpers this differs. The async atomic
update helpers perform in-place updates on the existing state. They call
drm_atomic_helper_cleanup_planes but the state pointer is not swapped.
This means that prepare_fb is called on the new_plane_state and
cleanup_fb is called on the new_plane_state (not the old).
In the case where old_plane_state->fb == new_plane_state->fb then
there should be no behavioral difference between an async update
and a non-async commit. But there are issues that arise when
old_plane_state->fb != new_plane_state->fb.
The first is that the new_plane_state->fb is immediately cleaned up
after it has been prepared, so we're using a fb that we shouldn't
be.
The second occurs during a sequence of async atomic updates and
non-async regular atomic commits. Suppose there are two framebuffers
being interleaved in a double-buffering scenario, fb1 and fb2:
MIPS: fix memory setup for platforms with PHYS_OFFSET != 0
For platforms, which use a PHYS_OFFSET != 0, symbol _end also
contains that offset. So when calling memblock_reserve() for
reserving kernel the size argument needs to be adjusted.
Fixes: bcec54bf3118 ("mips: switch to NO_BOOTMEM") Acked-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de> Signed-off-by: Paul Burton <paul.burton@mips.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: James Hogan <jhogan@kernel.org> Cc: linux-mips@vger.kernel.org Cc: linux-kernel@vger.kernel.org Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: stable@vger.kernel.org # v4.20+
Jann Horn [Wed, 27 Feb 2019 20:29:52 +0000 (21:29 +0100)]
mm: enforce min addr even if capable() in expand_downwards()
security_mmap_addr() does a capability check with current_cred(), but
we can reach this code from contexts like a VFS write handler where
current_cred() must not be used.
This can be abused on systems without SMAP to make NULL pointer
dereferences exploitable again.
Fixes: 8869477a49c3 ("security: protect from stack expansion into low vm addresses") Cc: stable@kernel.org Signed-off-by: Jann Horn <jannh@google.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
nfc_llcp_build_tlv will return NULL on fails, caller should check it,
otherwise will trigger a NULL dereference.
Reported-by: Hulk Robot <hulkci@huawei.com> Fixes: eda21f16a5ed ("NFC: Set MIU and RW values from CONNECT and CC LLCP frames") Fixes: d646960f7986 ("NFC: Initial LLCP support") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Mario Kleiner [Wed, 30 Jan 2019 05:04:46 +0000 (06:04 +0100)]
drm/amd/display: Use vrr friendly pageflip throttling in DC.
In VRR mode, keep track of the vblank count of the last
completed pageflip in amdgpu_crtc->last_flip_vblank, as
recorded in the pageflip completion handler after each
completed flip.
Use that count to prevent mmio programming a new pageflip
within the same vblank in which the last pageflip completed,
iow. to throttle pageflips to at most one flip per video
frame, while at the same time allowing to request a flip
not only before start of vblank, but also anywhere within
vblank.
The old logic did the same, and made sense for regular fixed
refresh rate flipping, but in vrr mode it prevents requesting
a flip anywhere inside the possibly huge vblank, thereby
reducing framerate in vrr mode instead of improving it, by
delaying a slightly delayed flip requests up to a maximum
vblank duration + 1 scanout duration. This would limit VRR
usefulness to only help applications with a very high GPU
demand, which can submit the flip request before start of
vblank, but then have to wait long for fences to complete.
With this method a flip can be both requested and - after
fences have completed - executed, ie. it doesn't matter if
the request (amdgpu_dm_do_flip()) gets delayed until deep
into the extended vblank due to cpu execution delays. This
also allows clients which want to regulate framerate within
the vrr range a much more fine-grained control of flip timing,
a feature that might be useful for video playback, and is
very useful for neuroscience/vision research applications.
In regular non-VRR mode, retain the old flip submission
behavior. This to keep flip scheduling for fullscreen X11/GLX
OpenGL clients intact, if they use the GLX_OML_sync_control
extensions glXSwapBufferMscOML(, ..., target_msc,...) function
with a specific target_msc target vblank count.
glXSwapBuffersMscOML() or DRI3/Present PresentPixmap() will
not flip at the proper target_msc for a non-zero target_msc
if VRR mode is active with this patch. They'd often flip one
frame too early. However, this limitation should not matter
much in VRR mode, as scheduling based on vblank counts is
pretty futile/unusable under variable refresh duration
anyway, so no real extra harm is done.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com> Cc: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Cc: Harry Wentland <harry.wentland@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: Michel Dänzer <michel@daenzer.net> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
net: phy: Micrel KSZ8061: link failure after cable connect
With Micrel KSZ8061 PHY, the link may occasionally not come up after
Ethernet cable connect. The vendor's (Microchip, former Micrel) errata
sheet 80000688A.pdf descripes the problem and possible workarounds in
detail, see below.
The batch implements workaround 1, which permanently fixes the issue.
DESCRIPTION
Link-up may not occur properly when the Ethernet cable is initially
connected. This issue occurs more commonly when the cable is connected
slowly, but it may occur any time a cable is connected. This issue occurs
in the auto-negotiation circuit, and will not occur if auto-negotiation
is disabled (which requires that the two link partners be set to the
same speed and duplex).
END USER IMPLICATIONS
When this issue occurs, link is not established. Subsequent cable
plug/unplaug cycle will not correct the issue.
WORk AROUND
There are four approaches to work around this issue:
1. This issue can be prevented by setting bit 15 in MMD device address 1,
register 2, prior to connecting the cable or prior to setting the
Restart Auto-negotiation bit in register 0h. The MMD registers are
accessed via the indirect access registers Dh and Eh, or via the Micrel
EthUtil utility as shown here:
. if using the EthUtil utility (usually with a Micrel KSZ8061
Evaluation Board), type the following commands:
> address 1
> mmd 1
> iw 2 b61a
. Alternatively, write the following registers to write to the
indirect MMD register:
Write register Dh, data 0001h
Write register Eh, data 0002h
Write register Dh, data 4001h
Write register Eh, data B61Ah
2. The issue can be avoided by disabling auto-negotiation in the KSZ8061,
either by the strapping option, or by clearing bit 12 in register 0h.
Care must be taken to ensure that the KSZ8061 and the link partner
will link with the same speed and duplex. Note that the KSZ8061
defaults to full-duplex when auto-negotiation is off, but other
devices may default to half-duplex in the event of failed
auto-negotiation.
3. The issue can be avoided by connecting the cable prior to powering-up
or resetting the KSZ8061, and leaving it plugged in thereafter.
4. If the above measures are not taken and the problem occurs, link can
be recovered by setting the Restart Auto-Negotiation bit in
register 0h, or by resetting or power cycling the device. Reset may
be either hardware reset or software reset (register 0h, bit 15).
PLAN
This errata will not be corrected in the future revision.
Fixes: 7ab59dc15e2f ("drivers/net/phy/micrel_phy: Add support for new PHYs") Signed-off-by: Alexander Onnasch <alexander.onnasch@landisgyr.com> Signed-off-by: Rajasingh Thavamani <T.Rajasingh@landisgyr.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Andy Shevchenko [Wed, 27 Feb 2019 10:45:35 +0000 (13:45 +0300)]
enc28j60: Correct description of debug module parameter
The netif_msg_init() API takes on input the amount of bits to be set. The
description of debug parameter in the enc28j60 module is misleading in this
sense and passing 0xffff does not give an expected behaviour.
Fix the description of debug module parameter to show what exactly is expected.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Wed, 27 Feb 2019 08:58:53 +0000 (03:58 -0500)]
bnxt_en: Drop oversize TX packets to prevent errors.
There have been reports of oversize UDP packets being sent to the
driver to be transmitted, causing error conditions. The issue is
likely caused by the dst of the SKB switching between 'lo' with
64K MTU and the hardware device with a smaller MTU. Patches are
being proposed by Mahesh Bandewar <maheshb@google.com> to fix the
issue.
In the meantime, add a quick length check in the driver to prevent
the error. The driver uses the TX packet size as index to look up an
array to setup the TX BD. The array is large enough to support all MTU
sizes supported by the driver. The oversize TX packet causes the
driver to index beyond the array and put garbage values into the
TX BD. Add a simple check to prevent this.
Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ming Lei [Wed, 27 Feb 2019 16:02:11 +0000 (00:02 +0800)]
mmc: core: align max segment size with logical block size
Logical block size is the lowest possible block size that the storage
device can address. Max segment size is often related with controller's
DMA capability. And it is reasonable to align max segment size with
logical block size.
SDHCI sets un-aligned max segment size, and causes ADMA error, so
fix it by aligning max segment size with logical block size.
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org> Cc: Christoph Hellwig <hch@lst.de> Cc: Naresh Kamboju <naresh.kamboju@linaro.org> Cc: Faiz Abbas <faiz_abbas@ti.com> Cc: linux-block@vger.kernel.org Signed-off-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Alamy Liu [Mon, 25 Feb 2019 19:22:14 +0000 (11:22 -0800)]
mmc: cqhci: Fix a tiny potential memory leak on error condition
Free up the allocated memory in the case of error return
The value of mmc_host->cqe_enabled stays 'false'. Thus, cqhci_disable
(mmc_cqe_ops->cqe_disable) won't be called to free the memory. Also,
cqhci_disable() seems to be designed to disable and free all resources, not
suitable to handle this corner case.
Fixes: a4080225f51d ("mmc: cqhci: support for command queue enabled host") Signed-off-by: Alamy Liu <alamy.liu@gmail.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Alamy Liu [Mon, 25 Feb 2019 19:22:13 +0000 (11:22 -0800)]
mmc: cqhci: fix space allocated for transfer descriptor
There is not enough space being allocated when DCMD is disabled.
CQE_DCMD is not necessary to be enabled when CQE is enabled.
(Software could halt CQE to send command)
In the case that CQE_DCMD is not enabled, it still needs to allocate
space for data transfer. For instance:
CQE_DCMD is enabled: 31 slots space (one slot used by DCMD)
CQE_DCMD is disabled: 32 slots space
Fixes: a4080225f51d ("mmc: cqhci: support for command queue enabled host") Signed-off-by: Alamy Liu <alamy.liu@gmail.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ritesh Harjani [Fri, 22 Feb 2019 13:51:34 +0000 (19:21 +0530)]
mmc: core: Fix NULL ptr crash from mmc_should_fail_request
In case of CQHCI, mrq->cmd may be NULL for data requests (non DCMD).
In such case mmc_should_fail_request is directly dereferencing
mrq->cmd while cmd is NULL.
Fix this by checking for mrq->cmd pointer.
Fixes: 72a5af554df8 ("mmc: core: Add support for handling CQE requests") Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org> Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tung Nguyen [Mon, 25 Feb 2019 03:57:20 +0000 (10:57 +0700)]
tipc: fix race condition causing hung sendto
When sending multicast messages via blocking socket,
if sending link is congested (tsk->cong_link_cnt is set to 1),
the sending thread will be put into sleeping state. However,
tipc_sk_filter_rcv() is called under socket spin lock but
tipc_wait_for_cond() is not. So, there is no guarantee that
the setting of tsk->cong_link_cnt to 0 in tipc_sk_proto_rcv() in
CPU-1 will be perceived by CPU-0. If that is the case, the sending
thread in CPU-0 after being waken up, will continue to see
tsk->cong_link_cnt as 1 and put the sending thread into sleeping
state again. The sending thread will sleep forever.
This commit fixes it by adding memory barrier to tipc_sk_proto_rcv()
and tipc_wait_for_cond().
Acked-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Haiyang Zhang [Fri, 22 Feb 2019 18:25:03 +0000 (18:25 +0000)]
hv_netvsc: Fix IP header checksum for coalesced packets
Incoming packets may have IP header checksum verified by the host.
They may not have IP header checksum computed after coalescing.
This patch re-compute the checksum when necessary, otherwise the
packets may be dropped, because Linux network stack always checks it.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 26 Feb 2019 21:23:17 +0000 (13:23 -0800)]
Merge branch 'net-fail-route'
David Ahern says:
====================
net: Fail route add with unsupported nexthop attribute
RTA_VIA was added for MPLS as a way of specifying a gateway from a
different address family. IPv4 and IPv6 do not currently support RTA_VIA
so using it leads to routes that are not what the user intended. Catch
and fail - returning a proper error message.
MPLS on the other hand does not support RTA_GATEWAY since it does not
make sense to have a nexthop from the MPLS address family. Similarly,
catch and fail - returning a proper error message.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Tue, 26 Feb 2019 17:00:04 +0000 (09:00 -0800)]
mpls: Return error for RTA_GATEWAY attribute
MPLS does not support nexthops with an MPLS address family.
Specifically, it does not handle RTA_GATEWAY attribute. Make it
clear by returning an error.
Fixes: 03c0566542f4c ("mpls: Netlink commands to add, remove, and dump routes") Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Tue, 26 Feb 2019 17:00:03 +0000 (09:00 -0800)]
ipv6: Return error for RTA_VIA attribute
IPv6 currently does not support nexthops outside of the AF_INET6 family.
Specifically, it does not handle RTA_VIA attribute. If it is passed
in a route add request, the actual route added only uses the device
which is clearly not what the user intended:
$ ip -6 ro add 2001:db8:2::/64 via inet 172.16.1.1 dev eth0
$ ip ro ls
...
2001:db8:2::/64 dev eth0 metric 1024 pref medium
Catch this and fail the route add:
$ ip -6 ro add 2001:db8:2::/64 via inet 172.16.1.1 dev eth0
Error: IPv6 does not support RTA_VIA attribute.
Fixes: 03c0566542f4c ("mpls: Netlink commands to add, remove, and dump routes") Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Tue, 26 Feb 2019 17:00:02 +0000 (09:00 -0800)]
ipv4: Return error for RTA_VIA attribute
IPv4 currently does not support nexthops outside of the AF_INET family.
Specifically, it does not handle RTA_VIA attribute. If it is passed
in a route add request, the actual route added only uses the device
which is clearly not what the user intended:
$ ip ro add 172.16.1.0/24 via inet6 2001:db8:1::1 dev eth0
$ ip ro ls
...
172.16.1.0/24 dev eth0
Catch this and fail the route add:
$ ip ro add 172.16.1.0/24 via inet6 2001:db8:1::1 dev eth0
Error: IPv4 does not support RTA_VIA attribute.
Fixes: 03c0566542f4c ("mpls: Netlink commands to add, remove, and dump routes") Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Peng Sun [Tue, 26 Feb 2019 14:15:37 +0000 (22:15 +0800)]
bpf: decrease usercnt if bpf_map_new_fd() fails in bpf_map_get_fd_by_id()
In bpf/syscall.c, bpf_map_get_fd_by_id() use bpf_map_inc_not_zero()
to increase the refcount, both map->refcnt and map->usercnt. Then, if
bpf_map_new_fd() fails, should handle map->usercnt too.
Fixes: bd5f5f4ecb78 ("bpf: Add BPF_MAP_GET_FD_BY_ID") Signed-off-by: Peng Sun <sironhide0null@gmail.com> Acked-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Julia Cartwright [Wed, 20 Feb 2019 16:46:31 +0000 (16:46 +0000)]
iommu/dmar: Fix buffer overflow during PCI bus notification
Commit 57384592c433 ("iommu/vt-d: Store bus information in RMRR PCI
device path") changed the type of the path data, however, the change in
path type was not reflected in size calculations. Update to use the
correct type and prevent a buffer overflow.
This bug manifests in systems with deep PCI hierarchies, and can lead to
an overflow of the static allocated buffer (dmar_pci_notify_info_buf),
or can lead to overflow of slab-allocated data.
Fixes: 57384592c433 ("iommu/vt-d: Store bus information in RMRR PCI device path") Signed-off-by: Julia Cartwright <julia@ni.com> Signed-off-by: Joerg Roedel <jroedel@suse.de>
Takeshi Saito [Thu, 21 Feb 2019 19:38:05 +0000 (20:38 +0100)]
mmc: tmio: fix access width of Block Count Register
In R-Car Gen2 or later, the maximum number of transfer blocks are
changed from 0xFFFF to 0xFFFFFFFF. Therefore, Block Count Register
should use iowrite32().
If another system (U-boot, Hypervisor OS, etc) uses bit[31:16], this
value will not be cleared. So, SD/MMC card initialization fails.
So, check for the bigger register and use apropriate write. Also, mark
the register as extended on Gen2.
Signed-off-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
[wsa: use max_blk_count in if(), add Gen2, update commit message] Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Cc: stable@kernel.org Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
[Ulf: Fixed build error] Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Jonas Gorski [Thu, 21 Feb 2019 09:56:42 +0000 (10:56 +0100)]
MIPS: BCM63XX: provide DMA masks for ethernet devices
The switch to the generic dma ops made dma masks mandatory, breaking
devices having them not set. In case of bcm63xx, it broke ethernet with
the following warning when trying to up the device:
David Howells [Thu, 21 Feb 2019 22:04:32 +0000 (22:04 +0000)]
afs: Fix manually set volume location server list
When a cell with a volume location server list is added manually by
echoing the details into /proc/net/afs/cells, a record is added but the
flag saying it has been looked up isn't set.
This causes the VL server rotation code to wait forever, with the top of
/proc/pid/stack looking like:
Darrick J. Wong [Sat, 23 Feb 2019 06:35:32 +0000 (22:35 -0800)]
tmpfs: fix uninitialized return value in shmem_link
When we made the shmem_reserve_inode call in shmem_link conditional, we
forgot to update the declaration for ret so that it always has a known
value. Dan Carpenter pointed out this deficiency in the original patch.
Fixes: 1062af920c07 ("tmpfs: fix link accounting when a tmpfile is linked in") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Hugh Dickins <hughd@google.com> Cc: Matej Kupljen <matej.kupljen@gmail.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Eric Biggers [Thu, 21 Feb 2019 22:13:56 +0000 (14:13 -0800)]
net: socket: set sock->sk to NULL after calling proto_ops::release()
Commit 9060cb719e61 ("net: crypto set sk to NULL when af_alg_release.")
fixed a use-after-free in sockfs_setattr() when an AF_ALG socket is
closed concurrently with fchownat(). However, it ignored that many
other proto_ops::release() methods don't set sock->sk to NULL and
therefore allow the same use-after-free:
Rather than fixing all these and relying on every socket type to get
this right forever, just make __sock_release() set sock->sk to NULL
itself after calling proto_ops::release().
Reproducer that produces the KASAN splat when any of these socket types
are configured into the kernel:
Fixes: 86741ec25462 ("net: core: Add a UID field to struct sock.") Signed-off-by: Eric Biggers <ebiggers@google.com> Acked-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vlad Buslov [Mon, 25 Feb 2019 15:28:27 +0000 (17:28 +0200)]
net: sched: act_tunnel_key: fix NULL pointer dereference during init
Metadata pointer is only initialized for action TCA_TUNNEL_KEY_ACT_SET, but
it is unconditionally dereferenced in tunnel_key_init() error handler.
Verify that metadata pointer is not NULL before dereferencing it in
tunnel_key_init error handling code.
Fixes: ee28bb56ac5b ("net/sched: fix memory leak in act_tunnel_key_init()") Signed-off-by: Vlad Buslov <vladbu@mellanox.com> Reviewed-by: Davide Caratti <dcaratti@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wen Yang [Mon, 25 Feb 2019 07:22:19 +0000 (15:22 +0800)]
net: dsa: fix a leaked reference by adding missing of_node_put
The call to of_parse_phandle returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./net/dsa/port.c:294:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 284, but without a corresponding object release within this function.
./net/dsa/dsa2.c:627:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 618, but without a corresponding object release within this function.
./net/dsa/dsa2.c:630:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 618, but without a corresponding object release within this function.
./net/dsa/dsa2.c:636:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 618, but without a corresponding object release within this function.
./net/dsa/dsa2.c:639:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 618, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn> Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Vivien Didelot <vivien.didelot@gmail.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Vivien Didelot <vivien.didelot@gmail.com> Cc: netdev@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
It was well-intentioned, but wrong. Overriding the exception tables for
instructions for random reasons is just wrong, and that is what the new
code did.
It caused problems for tracing, and it caused problems for strncpy_from_user(),
because the new checks made perfectly valid use cases break, rather than
catch things that did bad things.
Unchecked user space accesses are a problem, but that's not a reason to
add invalid checks that then people have to work around with silly flags
(in this case, that 'kernel_uaccess_faults_ok' flag, which is just an
odd way to say "this commit was wrong" and was sprinked into random
places to hide the wrongness).
The real fix to unchecked user space accesses is to get rid of the
special "let's not check __get_user() and __put_user() at all" logic.
Make __{get|put}_user() be just aliases to the regular {get|put}_user()
functions, and make it impossible to access user space without having
the proper checks in places.
The raison d'être of the special double-underscore versions used to be
that the range check was expensive, and if you did multiple user
accesses, you'd do the range check up front (like the signal frame
handling code, for example). But SMAP (on x86) and PAN (on ARM) have
made that optimization pointless, because the _real_ expense is the "set
CPU flag to allow user space access".
Do let's not break the valid cases to catch invalid cases that shouldn't
even exist.
Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Kees Cook <keescook@chromium.org> Cc: Tobin C. Harding <tobin@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Andy Lutomirski <luto@kernel.org> Cc: Jann Horn <jannh@google.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I have encountered an interrupt storm during the eMMC chip probing (and
the chip finally didn't get detected). It turned out that U-Boot left
the DMAC interrupts enabled while the Linux driver didn't use those.
The SDHI driver's interrupt handler somehow assumes that, even if an
SDIO interrupt didn't happen, it should return IRQ_HANDLED. I think
that if none of the enabled interrupts happened and got handled, we
should return IRQ_NONE -- that way the kernel IRQ code recoginizes
a spurious interrupt and masks it off pretty quickly...
Fixes: 7729c7a232a9 ("mmc: tmio: Provide separate interrupt handlers") Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When using the mmc_spi driver with a card-detect pin, I noticed that the
card was not detected immediately after probe, but only after it was
unplugged and plugged back in (and the CD IRQ fired).
Timur Celik [Sat, 23 Feb 2019 11:53:13 +0000 (12:53 +0100)]
tun: fix blocking read
This patch moves setting of the current state into the loop. Otherwise
the task may end up in a busy wait loop if none of the break conditions
are met.
Signed-off-by: Timur Celik <mail@timurcelik.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Davide Caratti [Fri, 22 Feb 2019 11:33:26 +0000 (12:33 +0100)]
net/sched: act_skbedit: fix refcount leak when replace fails
when act_skbedit was converted to use RCU in the data plane, we added an
error path, but we forgot to drop the action refcount in case of failure
during a 'replace' operation:
# tc actions add action skbedit ptype otherhost pass index 100
# tc action show action skbedit
total acts 1
action order 0: skbedit ptype otherhost pass
index 100 ref 1 bind 0
# tc actions replace action skbedit ptype otherhost drop index 100
RTNETLINK answers: Cannot allocate memory
We have an error talking to the kernel
# tc action show action skbedit
total acts 1
action order 0: skbedit ptype otherhost pass
index 100 ref 2 bind 0
Ensure we call tcf_idr_release(), in case 'params_new' allocation failed,
also when the action is being replaced.
Fixes: c749cdda9089 ("net/sched: act_skbedit: don't use spinlock in the data path") Signed-off-by: Davide Caratti <dcaratti@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Davide Caratti [Fri, 22 Feb 2019 11:33:25 +0000 (12:33 +0100)]
net/sched: act_ipt: fix refcount leak when replace fails
After commit 4e8ddd7f1758 ("net: sched: don't release reference on action
overwrite"), the error path of all actions was converted to drop refcount
also when the action was being overwritten. But we forgot act_ipt_init(),
in case allocation of 'tname' was not successful:
# tc action add action xt -j LOG --log-prefix hello index 100
tablename: mangle hook: NF_IP_POST_ROUTING
target: LOG level warning prefix "hello" index 100
# tc action show action xt
total acts 1
action order 0: tablename: mangle hook: NF_IP_POST_ROUTING
target LOG level warning prefix "hello"
index 100 ref 1 bind 0
# tc action replace action xt -j LOG --log-prefix world index 100
tablename: mangle hook: NF_IP_POST_ROUTING
target: LOG level warning prefix "world" index 100
RTNETLINK answers: Cannot allocate memory
We have an error talking to the kernel
# tc action show action xt
total acts 1
action order 0: tablename: mangle hook: NF_IP_POST_ROUTING
target LOG level warning prefix "hello"
index 100 ref 2 bind 0
Ensure we call tcf_idr_release(), in case 'tname' allocation failed, also
when the action is being replaced.
Fixes: 4e8ddd7f1758 ("net: sched: don't release reference on action overwrite") Signed-off-by: Davide Caratti <dcaratti@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 24 Feb 2019 17:47:07 +0000 (09:47 -0800)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"Bug fixes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: MMU: record maximum physical address width in kvm_mmu_extended_role
kvm: x86: Return LA57 feature based on hardware capability
x86/kvm/mmu: fix switch between root and guest MMUs
s390: vsie: Use effective CRYCBD.31 to check CRYCBD validity
Pull networking fixes from David Miller:
"Hopefully the last pull request for this release. Fingers crossed:
1) Only refcount ESP stats on full sockets, from Martin Willi.
2) Missing barriers in AF_UNIX, from Al Viro.
3) RCU protection fixes in ipv6 route code, from Paolo Abeni.
4) Avoid false positives in untrusted GSO validation, from Willem de
Bruijn.
5) Forwarded mesh packets in mac80211 need more tailroom allocated,
from Felix Fietkau.
6) Use operstate consistently for linkup in team driver, from George
Wilkie.
7) ThunderX bug fixes from Vadim Lomovtsev. Mostly races between VF
and PF code paths.
8) Purge ipv6 exceptions during netdevice removal, from Paolo Abeni.
9) nfp eBPF code gen fixes from Jiong Wang.
10) bnxt_en firmware timeout fix from Michael Chan.
11) Use after free in udp/udpv6 error handlers, from Paolo Abeni.
12) Fix a race in x25_bind triggerable by syzbot, from Eric Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (65 commits)
net: phy: realtek: Dummy IRQ calls for RTL8366RB
tcp: repaired skbs must init their tso_segs
net/x25: fix a race in x25_bind()
net: dsa: Remove documentation for port_fdb_prepare
Revert "bridge: do not add port to router list when receives query with source 0.0.0.0"
selftests: fib_tests: sleep after changing carrier. again.
net: set static variable an initial value in atl2_probe()
net: phy: marvell10g: Fix Multi-G advertisement to only advertise 10G
bpf, doc: add bpf list as secondary entry to maintainers file
udp: fix possible user after free in error handler
udpv6: fix possible user after free in error handler
fou6: fix proto error handler argument type
udpv6: add the required annotation to mib type
mdio_bus: Fix use-after-free on device_register fails
net: Set rtm_table to RT_TABLE_COMPAT for ipv6 for tables > 255
bnxt_en: Wait longer for the firmware message response to complete.
bnxt_en: Fix typo in firmware message timeout logic.
nfp: bpf: fix ALU32 high bits clearance bug
nfp: bpf: fix code-gen bug on BPF_ALU | BPF_XOR | BPF_K
Documentation: networking: switchdev: Update port parent ID section
...
Linus Walleij [Sun, 24 Feb 2019 00:11:15 +0000 (01:11 +0100)]
net: phy: realtek: Dummy IRQ calls for RTL8366RB
This fixes a regression introduced by
commit 0d2e778e38e0ddffab4bb2b0e9ed2ad5165c4bf7
"net: phy: replace PHY_HAS_INTERRUPT with a check for
config_intr and ack_interrupt".
This assumes that a PHY cannot trigger interrupt unless
it has .config_intr() or .ack_interrupt() implemented.
A later patch makes the code assume both need to be
implemented for interrupts to be present.
But this PHY (which is inside a DSA) will happily
fire interrupts without either callback.
Implement dummy callbacks for .config_intr() and
.ack_interrupt() in the phy header to fix this.
Tested on the RTL8366RB on D-Link DIR-685.
Fixes: 0d2e778e38e0 ("net: phy: replace PHY_HAS_INTERRUPT with a check for config_intr and ack_interrupt") Cc: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sat, 23 Feb 2019 21:24:59 +0000 (13:24 -0800)]
net/x25: fix a race in x25_bind()
syzbot was able to trigger another soft lockup [1]
I first thought it was the O(N^2) issue I mentioned in my
prior fix (f657d22ee1f "net/x25: do not hold the cpu
too long in x25_new_lci()"), but I eventually found
that x25_bind() was not checking SOCK_ZAPPED state under
socket lock protection.
This means that multiple threads can end up calling
x25_insert_socket() for the same socket, and corrupt x25_list
Fixes: 90c27297a9bf ("X.25 remove bkl in bind") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: andrew hendry <andrew.hendry@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Hangbin Liu [Fri, 22 Feb 2019 13:22:32 +0000 (21:22 +0800)]
Revert "bridge: do not add port to router list when receives query with source 0.0.0.0"
This reverts commit 5a2de63fd1a5 ("bridge: do not add port to router list
when receives query with source 0.0.0.0") and commit 0fe5119e267f ("net:
bridge: remove ipv6 zero address check in mcast queries")
The reason is RFC 4541 is not a standard but suggestive. Currently we
will elect 0.0.0.0 as Querier if there is no ip address configured on
bridge. If we do not add the port which recives query with source
0.0.0.0 to router list, the IGMP reports will not be about to forward
to Querier, IGMP data will also not be able to forward to dest.
As Nikolay suggested, revert this change first and add a boolopt api
to disable none-zero election in future if needed.
Reported-by: Linus Lüssing <linus.luessing@c0d3.blue> Reported-by: Sebastian Gottschall <s.gottschall@newmedia-net.de> Fixes: 5a2de63fd1a5 ("bridge: do not add port to router list when receives query with source 0.0.0.0") Fixes: 0fe5119e267f ("net: bridge: remove ipv6 zero address check in mcast queries") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
selftests: fib_tests: sleep after changing carrier. again.
Just like commit e2ba732a1681 ("selftests: fib_tests: sleep after
changing carrier"), wait one second to allow linkwatch to propagate the
carrier change to the stack.
There are two sets of carrier tests. The first slept after the carrier
was set to off, and when the second set ran, it was likely that the
linkwatch would be able to run again without much delay, reducing the
likelihood of a race. However, if you run 'fib_tests.sh -t carrier' on a
loop, you will quickly notice the failures.
Sleeping on the second set of tests make the failures go away.
Cc: David Ahern <dsahern@gmail.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Mao Wenan [Fri, 22 Feb 2019 06:57:23 +0000 (14:57 +0800)]
net: set static variable an initial value in atl2_probe()
cards_found is a static variable, but when it enters atl2_probe(),
cards_found is set to zero, the value is not consistent with last probe,
so next behavior is not our expect.
Signed-off-by: Mao Wenan <maowenan@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: phy: marvell10g: Fix Multi-G advertisement to only advertise 10G
Some Marvell Alaska PHYs support 2.5G, 5G and 10G BaseT links. Their
default behaviour is to advertise all of these modes, but at the moment,
only 10GBaseT is supported. To prevent link partners from establishing
link at that speed, clear these modes upon configuring aneg parameters.
Fixes: 20b2af32ff3f ("net: phy: add Marvell Alaska X 88X3310 10Gigabit PHY support") Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Reported-by: Russell King <linux@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 23 Feb 2019 17:48:01 +0000 (09:48 -0800)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Four small fixes: three in drivers and one in the core.
The core fix is also minor in scope since the bug it fixes is only
known to affect systems using SCSI reservations. Of the driver bugs,
the libsas one is the most major because it can lead to multiple disks
on the same expander not being exposed"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: core: reset host byte in DID_NEXUS_FAILURE case
scsi: libsas: Fix rphy phy_identifier for PHYs with end devices attached
scsi: sd_zbc: Fix sd_zbc_report_zones() buffer allocation
scsi: libiscsi: Fix race between iscsi_xmit_task and iscsi_complete_task
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix a bug in BPF's LPM deletion logic to match correct prefix
length, from Alban.
2) Fix AF_XDP teardown by not destroying umem prematurely as it
is still needed till all outstanding skbs are freed, from Björn.
3) Fix unkillable BPF_PROG_TEST_RUN under preempt kernel by checking
signal_pending() outside need_resched() condition which is never
triggered there, from Stanislav.
4) Fix two nfp JIT bugs, one in code emission for K-based xor, and
another one to explicitly clear upper bits in alu32, from Jiong.
5) Add bpf list address to maintainers file, from Daniel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 23 Feb 2019 01:46:30 +0000 (17:46 -0800)]
Merge tag 'pm-5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix a regression in the PM-runtime framework introduced by the
recent switch-over of it to using hrtimers and a use-after-free
introduced by one of the recent changes in the scmi-cpufreq driver.
Specifics:
- Use hrtimer_try_to_cancel() instead of hrtimer_cancel() in the
PM-runtime framework to avoid a possible timer-related deadlock
introduced recently (Vincent Guittot).
- Reorder the scmi-cpufreq driver code to avoid accessing memory that
has just been freed (Yangtao Li)"
* tag 'pm-5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM-runtime: Fix deadlock when canceling hrtimer
cpufreq: scmi: Fix use-after-free in scmi_cpufreq_exit()
Linus Torvalds [Sat, 23 Feb 2019 00:31:26 +0000 (16:31 -0800)]
Merge tag 'arc-5.0-final' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC fixes from Vineet Gupta:
"Fixes for ARC for 5.0, bunch of those are stable fodder anyways so
sooner the better.
- Fix memcpy to prevent prefetchw beyond end of buffer [Eugeniy]
- Enable unaligned access early to prevent exceptions given newer gcc
code gen [Eugeniy]
- Tighten up uboot arg checking to prevent false negatives and also
allow both jtag and bootloading to coexist w/o config option as
needed by kernelCi folks [Eugeniy]
- Set slab alignment to 8 for ARC to avoid the atomic64_t unalign
[Alexey]
- Disable regfile auto save on interrupts on HSDK platform due to a
silicon issue [Vineet]
- Avoid HS38x boot printing crash by not reading HS48x only reg
[Vineet]"
* tag 'arc-5.0-final' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARCv2: don't assume core 0x54 has dual issue
ARC: define ARCH_SLAB_MINALIGN = 8
ARC: enable uboot support unconditionally
ARC: U-boot: check arguments paranoidly
ARCv2: support manual regfile save on interrupts
ARC: uacces: remove lp_start, lp_end from clobber list
ARC: fix actionpoints configuration detection
ARCv2: lib: memcpy: fix doing prefetchw outside of buffer
ARCv2: Enable unaligned access in early ASM code
Daniel Borkmann [Fri, 22 Feb 2019 23:03:44 +0000 (00:03 +0100)]
bpf, doc: add bpf list as secondary entry to maintainers file
We recently created a bpf@vger.kernel.org list (https://lore.kernel.org/bpf/)
for BPF related discussions, originally in context of BPF track at LSF/MM
for topic discussions. It's *optional* but *desirable* to keep it in Cc for
BPF related kernel/loader/llvm/tooling threads, meaning also infrastructure
like llvm that sits on top of kernel but is crucial to BPF. In any case,
netdev with it's bpf delegate is *as-is* today primary list for patches, so
nothing changes in the workflow. Main purpose is to have some more awareness
for the bpf@vger.kernel.org list that folks can Cc for BPF specific topics.
Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Linus Torvalds [Sat, 23 Feb 2019 00:12:01 +0000 (16:12 -0800)]
Merge branch 'parisc-5.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc fixes from Helge Deller:
"Fix ptrace syscall number modification which has been broken since
kernel v4.5 and provide alternative email addresses for the remaining
users of the retired parisc-linux.org email domain"
* 'parisc-5.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
CREDITS/MAINTAINERS: Retire parisc-linux.org email domain
parisc: Fix ptrace syscall number modification
projects / mirror_ubuntu-eoan-kernel.git / log