The video_device debug field has been renamed to dev_debug, resulting in
a compilation failure. As v4l2 debugging is supposed to be controlled
through a sysfs attribute created by the v4l2 core, there's no need to
duplicate debug control through a module parameter. Remove it.
The UVC spec is a bit vague wrt devices using bulk endpoints,
specifically, how to signal to a device to start streaming.
For devices using isoc endpoints, the sequence for start streaming is:
1) The host sends PROBE_CONTROL(SET_CUR) PROBE_CONTROL(GET_CUR)
2) Host selects desired config and calls COMMIT_CONTROL(SET_CUR)
3) Host selects an alt interface other then zero - e.g SELECT_ALTERNATE_INTERFACE(1)
4) The device starts streaming
However for devices using bulk endpoints, there must be *no* alt interface
other than setting zero. From the UVC spec:
"A VideoStreaming interface containing a bulk endpoint for streaming shall
support only alternate setting zero. Additional alternate settings containing
bulk endpoints are not permitted in a device that is compliant with the Video
Class specification."
So for devices using bulk endpoints, step #3 above is irrelevant, and thus
cannot be used as an indication for the device to start streaming.
So in practice, such devices start streaming immediately after a
COMMIT_CONTROL(SET_CUR).
In the uvc resume() handler, an unsolicited commit is sent, which causes
devices using bulk endpoints to start streaming unintentionally.
This patch modifies resume() handler to send a commit only if streaming
needs to be reestablished, i.e if the device was actually streaming before is
was suspended.
Hans Verkuil [Fri, 19 Dec 2014 12:14:22 +0000 (09:14 -0300)]
[media] hdmi: rename HDMI_AUDIO_CODING_TYPE_EXT_STREAM to _EXT_CT
As per the suggestion of Thierry Reding rename
HDMI_AUDIO_CODING_TYPE_EXT_STREAM to HDMI_AUDIO_CODING_TYPE_EXT_CT to
be consistent with the CEA-861 spec.
Martin Bugge [Fri, 19 Dec 2014 12:14:21 +0000 (09:14 -0300)]
[media] hdmi: added unpack and logging functions for InfoFrames
When receiving video it is very useful to be able to unpack the InfoFrames.
Logging is useful as well, both for transmitters and receivers.
Especially when implementing the VIDIOC_LOG_STATUS ioctl (supported by many
V4L2 drivers) for a receiver it is important to be able to easily log what
the InfoFrame contains. This greatly simplifies debugging.
Signed-off-by: Martin Bugge <marbugge@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Acked-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Dan Carpenter [Thu, 8 Jan 2015 10:07:08 +0000 (07:07 -0300)]
[media] coda: improve safety in coda_register_device()
The "i" variable is used as an offset into both the dev->vfd[] and the
dev->devtype->vdevs[] arrays. The second array is smaller so we should
use that as a limit instead of ARRAY_SIZE(dev->vfd). Also the original
check was off by one.
We should use a format string as well in case the ->name has any funny
characters and also to stop static checkers from complaining.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Ondrej Zary [Thu, 15 Jan 2015 20:10:45 +0000 (17:10 -0300)]
[media] bttv: Convert to generic TEA575x interface
Remove tea575x-specific code from bttv and use the common driver instead.
Only set_frequency is implemented (signal/stereo detection or seek would
require more changes to bttv).
It works fine on Video Highway Xtreme (it actually makes the radio usable as
it currently cannot be tuned properly).
Miro/Pinnacle is untested but seems to be simple and should work.
However, I don't understand the Terratec Active Radio Upgrade code. The HW
seems to need IOR, IOW and CSEL signals that were taken from ISA bus on
older cards (IOR and IOW directly and CSEL from some address decoder) and
are emulated here using GPIOs. But the code manipulating these signals in
bttv seems to be broken - it never asserts the IOR signal. If anyone has
this HW, please test if I got that right.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Hans Verkuil [Tue, 23 Dec 2014 12:46:27 +0000 (09:46 -0300)]
[media] videobuf: make unused exported functions static
The videobuf_dma_init* and videobuf_dma_map() functions are no longer
used except in videobuf-dma-sg.c itself. Make them static.
These functions were abused in various drivers. All those drivers
have now been fixed, so by no longer exporting these functions
future abuse is now prevented.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This is needed in order to get the media fixes applied on -rc6.
Linux 3.19-rc6
* tag 'v3.19-rc6': (891 commits)
Linux 3.19-rc6
dm: fix handling of multiple internal suspends
hwmon: (i5500_temp) Convert to use ATTRIBUTE_GROUPS macro
hwmon: (i5500_temp) Convert to module_pci_driver
hwmon: (i5500_temp) Don't bind to disabled sensors
hwmon: (i5500_temp) Convert to devm_hwmon_device_register_with_groups
hwmon: (i5500_temp) New driver for the Intel 5500/5520/X58 chipsets
arm64: dts: add baud rate to Juno stdout-path
Revert "platform: x86: dell-laptop: Add support for keyboard backlight"
Revert "Documentation: Add entry for dell-laptop sysfs interface"
dm cache: fix problematic dual use of a single migration count variable
dm cache: share cache-metadata object across inactive and active DM tables
of/unittest: Overlays with sub-devices tests
KVM: x86: SYSENTER emulation is broken
KVM: x86: Fix of previously incomplete fix for CVE-2014-8480
arm64: dump: Fix implicit inclusion of definition for PCI_IOBASE
x86/tsc: Change Fast TSC calibration failed from error to info
x86/apic: Re-enable PCI_MSI support for non-SMP X86_32
x86, mm: Change cachemode exports to non-gpl
x86, tls: Interpret an all-zero struct user_desc as "no segment"
...
Jurgen Kramer [Mon, 8 Dec 2014 08:30:44 +0000 (05:30 -0300)]
[media] Si2168: increase timeout to fix firmware loading
Increase si2168 cmd execute timeout to prevent firmware load failures. Tests
shows it takes up to 52ms to load the 'dvb-demod-si2168-a30-01.fw' firmware.
Increase timeout to a safe value of 70ms.
Linus Torvalds [Mon, 26 Jan 2015 02:11:17 +0000 (18:11 -0800)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"Hopefully the last round of fixes for 3.19
- regression fix for the LDT changes
- regression fix for XEN interrupt handling caused by the APIC
changes
- regression fixes for the PAT changes
- last minute fixes for new the MPX support
- regression fix for 32bit UP
- fix for a long standing relocation issue on 64bit tagged for stable
- functional fix for the Hyper-V clocksource tagged for stable
- downgrade of a pr_err which tends to confuse users
Looks a bit on the large side, but almost half of it are valuable
comments"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/tsc: Change Fast TSC calibration failed from error to info
x86/apic: Re-enable PCI_MSI support for non-SMP X86_32
x86, mm: Change cachemode exports to non-gpl
x86, tls: Interpret an all-zero struct user_desc as "no segment"
x86, tls, ldt: Stop checking lm in LDT_empty
x86, mpx: Strictly enforce empty prctl() args
x86, mpx: Fix potential performance issue on unmaps
x86, mpx: Explicitly disable 32-bit MPX support on 64-bit kernels
x86, hyperv: Mark the Hyper-V clocksource as being continuous
x86: Don't rely on VMWare emulating PAT MSR correctly
x86, irq: Properly tag virtualization entry in /proc/interrupts
x86, boot: Skip relocs when load address unchanged
x86/xen: Override ACPI IRQ management callback __acpi_unregister_gsi
ACPI: pci: Do not clear pci_dev->irq in acpi_pci_irq_disable()
x86/xen: Treat SCI interrupt as normal GSI interrupt
Linus Torvalds [Mon, 26 Jan 2015 02:07:01 +0000 (18:07 -0800)]
Merge branch 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"From the irqchip departement you get:
- regression fix for omap-intc
- regression fix for atmel-aic-common
- functional correctness fix for hip04
- type mismatch fix for gic-v3-its
- proper error pointer check for mtd-sysirq
Mostly one and two liners except for the omap regression fix which is
slightly larger than desired"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip: atmel-aic-common: Prevent clobbering of priority when changing IRQ type
irqchip: omap-intc: Fix legacy DMA regression
irqchip: gic-v3-its: Fix use of max with decimal constant
irqchip: hip04: Initialize hip04_cpu_map to 0xffff
irqchip: mtk-sysirq: Use IS_ERR() instead of NULL pointer check
Linus Torvalds [Mon, 26 Jan 2015 01:47:34 +0000 (17:47 -0800)]
Merge branch 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Thomas Gleixner:
"A set of small fixes:
- regression fix for exynos_mct clocksource
- trivial build fix for kona clocksource
- functional one liner fix for the sh_tmu clocksource
- two validation fixes to prevent (root only) data corruption in the
kernel via settimeofday and adjtimex. Tagged for stable"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
time: adjtimex: Validate the ADJ_FREQUENCY values
time: settimeofday: Validate the values of tv from user
clocksource: sh_tmu: Set cpu_possible_mask to fix SMP broadcast
clocksource: kona: fix __iomem annotation
clocksource: exynos_mct: Fix bitmask regression for exynos4_mct_write
Linus Torvalds [Mon, 26 Jan 2015 01:29:06 +0000 (17:29 -0800)]
Merge tag 'armsoc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A week's worth of fixes for various ARM platforms. Diff wise, the
largest fix is for OMAP to deal with how GIC now registers interrupts
(irq_domain_add_legacy() -> irq_domain_add_linear() changes).
Besides this, a few more renesas platforms needed the GIC instatiation
done for legacy boards. There's also a fix that disables coherency of
mvebu due to issues, and a few other smaller fixes"
* tag 'armsoc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arm64: dts: add baud rate to Juno stdout-path
ARM: dts: imx25: Fix PWM "per" clocks
bus: mvebu-mbus: fix support of MBus window 13
Merge tag 'mvebu-fixes-3.19-3' of git://git.infradead.org/linux-mvebu into fixes
ARM: mvebu: completely disable hardware I/O coherency
ARM: OMAP: Work around hardcoded interrupts
ARM: shmobile: r8a7779: Instantiate GIC from C board code in legacy builds
ARM: shmobile: r8a7778: Instantiate GIC from C board code in legacy builds
arm: boot: dts: dra7: enable dwc3 suspend PHY quirk
Linus Torvalds [Mon, 26 Jan 2015 01:27:18 +0000 (17:27 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs fixes from Al Viro:
"A couple of fixes - deadlock in CIFS and build breakage in cris serial
driver (resurfaced f_dentry in there)"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
VFS: Convert file->f_dentry->d_inode to file_inode()
fix deadlock in cifs_ioctl_clone()
Linus Torvalds [Mon, 26 Jan 2015 01:25:01 +0000 (17:25 -0800)]
Merge tag 'dm-3.19-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
"Two stable fixes for dm-cache and one 3.19 DM core fix:
- fix potential for dm-cache metadata corruption via stale metadata
buffers being used when switching an inactive cache table to
active; this could occur due to each table having it's own bufio
client rather than sharing the client between tables.
- fix dm-cache target to properly account for discard IO while
suspending otherwise IO quiescing could complete prematurely.
- fix DM core's handling of multiple internal suspends by maintaining
an 'internal_suspend_count' and only resuming the device when this
count drops to zero"
* tag 'dm-3.19-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm: fix handling of multiple internal suspends
dm cache: fix problematic dual use of a single migration count variable
dm cache: share cache-metadata object across inactive and active DM tables
Linus Torvalds [Mon, 26 Jan 2015 01:23:34 +0000 (17:23 -0800)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull two block layer fixes from Jens Axboe:
"Two small patches that should make it into 3.19:
- a fixup from me for NVMe, making the cq_vector a signed variable.
Otherwise our -1 comparison fails, and commit 2b25d981790b doesn't
do what it was supposed to.
- a fixup for the hotplug handling for blk-mq from Ming Lei, using
the proper kobject referencing to ensure we release resources at
the right time"
* 'for-linus' of git://git.kernel.dk/linux-block:
blk-mq: fix hctx/ctx kobject use-after-free
NVMe: cq_vector should be signed
Linus Torvalds [Sat, 24 Jan 2015 22:52:30 +0000 (14:52 -0800)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
pULL SCSI fixes from James Bottomley:
"This consists of four real fixes and three MAINTAINER updates.
Three of the fixes are obvious (the DIX and atomic allocation are bug
on and warn on fixes and the other is just trivial) and the ipr one is
a bit more involved but is required because without it, the card
double completes aborted commands and causes a kernel oops"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
MAINTAINERS: ibmvscsi driver maintainer change
MAINTAINERS: ibmvfc driver maintainer change
MAINTAINERS: Remove self as isci maintainer
scsi_debug: test always evaluates to false, || should be used instead
scsi: Avoid crashing if device uses DIX but adapter does not support it
scsi_debug: use atomic allocation in resp_rsup_opcodes
ipr: wait for aborted command responses
Linus Torvalds [Sat, 24 Jan 2015 22:47:24 +0000 (14:47 -0800)]
Merge git://www.linux-watchdog.org/linux-watchdog
Pull watchdog fixes from Wim Van Sebroeck:
"This will fix reboot issues with the imx2_wdt driver and it also drops
some forgotten owner assignments from platform_drivers"
* git://www.linux-watchdog.org/linux-watchdog:
watchdog: drop owner assignment from platform_drivers
watchdog: imx2_wdt: Disable power down counter on boot
watchdog: imx2_wdt: Improve power management support.
Linus Torvalds [Sat, 24 Jan 2015 22:37:31 +0000 (14:37 -0800)]
Merge branch 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging
Pull hwmon update from Jean Delvare:
"This contains a single thing: a new driver for the temperature sensor
embedded in the Intel 5500/5520/X58 chipsets.
Sorry for the late request, it's been so long since I last sent a pull
request and I've been so busy with other tasks meanwhile that I simply
forgot about these patches. But given that this is a new driver, it
can't introduce any regression so I thought it could still be OK.
This has been in linux-next for months now"
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: (i5500_temp) Convert to use ATTRIBUTE_GROUPS macro
hwmon: (i5500_temp) Convert to module_pci_driver
hwmon: (i5500_temp) Don't bind to disabled sensors
hwmon: (i5500_temp) Convert to devm_hwmon_device_register_with_groups
hwmon: (i5500_temp) New driver for the Intel 5500/5520/X58 chipsets
Linus Torvalds [Sat, 24 Jan 2015 22:34:54 +0000 (14:34 -0800)]
Merge tag 'media/v3.19-4' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
- fix some race conditions caused by a regression on videobuf2
- fix a interrupt release bug on cx23885
- fix support for Mygica T230 and HVR4400
- fix compilation breakage when USB is not selected on tlg2300
- fix capabilities report on ompa3isp, soc-camera, rcar_vin and
pvrusb2
* tag 'media/v3.19-4' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] omap3isp: Correctly set QUERYCAP capabilities
[media] cx23885: fix free interrupt bug
[media] pvrusb2: fix missing device_caps in querycap
[media] vb2: fix vb2_thread_stop race conditions
[media] rcar_vin: Update device_caps and capabilities in querycap
[media] soc-camera: fix device capabilities in multiple camera host drivers
[media] Fix Mygica T230 support
[media] cx23885: Split Hauppauge WinTV Starburst from HVR4400 card entry
[media] tlg2300: Fix media dependencies
Mikulas Patocka [Thu, 8 Jan 2015 23:52:26 +0000 (18:52 -0500)]
dm: fix handling of multiple internal suspends
Commit ffcc393641 ("dm: enhance internal suspend and resume interface")
attempted to handle multiple internal suspends on the same device, but
it did that incorrectly. When these functions are called in this order
on the same device the device is no longer suspended, but it should be:
dm_internal_suspend_noflush
dm_internal_suspend_noflush
dm_internal_resume
Fix this bug by maintaining an 'internal_suspend_count' and resuming
the device when this count drops to zero.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Jean Delvare [Sat, 24 Jan 2015 13:16:21 +0000 (14:16 +0100)]
hwmon: (i5500_temp) Don't bind to disabled sensors
On many motherboards, for an unknown reason, the thermal sensor seems
to be disabled and will return a constant temperature value of 36.5
degrees Celsius. Don't bind to the device in that case, so that we
don't report this bogus value to userspace.
Linus Torvalds [Sat, 24 Jan 2015 02:31:27 +0000 (14:31 +1200)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"We have a few fixes in my for-linus branch.
Qu Wenruo's batch fix a regression between some our merge window pull
and the inode_cache feature. The rest are smaller bugs"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
btrfs: Don't call btrfs_start_transaction() on frozen fs to avoid deadlock.
btrfs: Fix the bug that fs_info->pending_changes is never cleared.
btrfs: fix state->private cast on 32 bit machines
Btrfs: fix race deleting block group from space_info->ro_bgs list
Btrfs: fix incorrect freeing in scrub_stripe
btrfs: sync ioctl, handle errors after transaction start
Linus Torvalds [Fri, 23 Jan 2015 23:26:13 +0000 (11:26 +1200)]
Merge tag 'platform-drivers-x86-v3.19-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86
Pull platform driver fix from Darren Hart:
"Revert keyboard backlight sysfs support and documentation.
The support for the dell-laptop keyboard backlight was flawed and the
fix:
https://lkml.org/lkml/2015/1/14/539
was more invasive that I felt comfortable sending at RC5.
This series reverts the support for the dell-laptop keyboard backlight
as well as the documentation for the newly created sysfs attributes.
We'll get this implemented correctly for 3.20"
* tag 'platform-drivers-x86-v3.19-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
Revert "platform: x86: dell-laptop: Add support for keyboard backlight"
Revert "Documentation: Add entry for dell-laptop sysfs interface"
Linus Torvalds [Fri, 23 Jan 2015 22:58:47 +0000 (10:58 +1200)]
Merge tag 'pci-v3.19-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"These are fixes for:
- a resource management problem that causes a Radeon "Fatal error
during GPU init" on machines where the BIOS programmed an invalid
Root Port window. This was a regression in v3.16.
- an Atheros AR93xx device that doesn't handle PCI bus resets
correctly. This was a regression in v3.14.
- an out-of-date email address"
* tag 'pci-v3.19-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
MAINTAINERS: Update Richard Zhu's email address
sparc/PCI: Clip bridge windows to fit in upstream windows
powerpc/PCI: Clip bridge windows to fit in upstream windows
parisc/PCI: Clip bridge windows to fit in upstream windows
mn10300/PCI: Clip bridge windows to fit in upstream windows
microblaze/PCI: Clip bridge windows to fit in upstream windows
ia64/PCI: Clip bridge windows to fit in upstream windows
frv/PCI: Clip bridge windows to fit in upstream windows
alpha/PCI: Clip bridge windows to fit in upstream windows
x86/PCI: Clip bridge windows to fit in upstream windows
PCI: Add pci_claim_bridge_resource() to clip window if necessary
PCI: Add pci_bus_clip_resource() to clip to fit upstream window
PCI: Pass bridge device, not bus, when updating bridge windows
PCI: Mark Atheros AR93xx to avoid bus reset
PCI: Add flag for devices where we can't use bus reset
Linus Torvalds [Fri, 23 Jan 2015 22:55:05 +0000 (10:55 +1200)]
Merge tag 'devicetree-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux
Pull devicetree bug fixes and documentation updates from Grant Likely:
"A few bugfixes for the new DT overlay feature, documentation updates,
spelling corrections, and changes to MAINTAINERS. Nothing earth
shattering here"
* tag 'devicetree-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux:
of/unittest: Overlays with sub-devices tests
of/platform: Handle of_populate drivers in notifier
of/overlay: Do not generate duplicate nodes
devicetree: document the "qemu" and "virtio" vendor prefixes
devicetree: document ARM bindings for QEMU's Firmware Config interface
Documentation: of: fix typo in graph bindings
dma-mapping: fix debug print to display correct dma_pfn_offset
of: replace Asahi Kasei Corp vendor prefix
ARM: dt: GIC: Spelling s/specific/specifier/, s/flaggs/flags/
dt/bindings: arm-boards: Spelling s/pointong/pointing/
MAINTAINERS: Update DT website and git repository
MAINTAINERS: drop DT regex matching on of_get_property and of_match_table
Robin Murphy [Thu, 22 Jan 2015 11:21:32 +0000 (11:21 +0000)]
arm64: dts: add baud rate to Juno stdout-path
Without explicit command-line parameters, the Juno UART ends up running
at 57600 baud in the kernel, which is at odds with the 115200 baud used
by the rest of the firmware. Since commit 7914a7c5651a5161 now lets us
fix this by specifying default options in stdout-path, do so.
Acked-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Robin Murphy <robin.murphy@arm.com> Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Fri, 23 Jan 2015 22:08:13 +0000 (14:08 -0800)]
Merge tag 'mvebu-fixes-3.19-4' of git://git.infradead.org/linux-mvebu into fixes
Merge "mvebu/fixes #3" from Andrew Lunn:
mvebu fixes for 3.19. (Part 4)
bus: mvebu-mbus: fix support of MBus window 13
* tag 'mvebu-fixes-3.19-4' of git://git.infradead.org/linux-mvebu:
bus: mvebu-mbus: fix support of MBus window 13
ARM: mvebu: completely disable hardware I/O coherency
Linus Torvalds [Fri, 23 Jan 2015 21:58:17 +0000 (09:58 +1200)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"Three small fixes.
Two for x86 and one avoids that sparse bails out"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: SYSENTER emulation is broken
KVM: x86: Fix of previously incomplete fix for CVE-2014-8480
KVM: fix sparse warning in include/trace/events/kvm.h
Linus Torvalds [Fri, 23 Jan 2015 21:57:01 +0000 (09:57 +1200)]
Merge branch 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm
Pull ARM fixes from Russell King:
"Another round of small ARM fixes.
restore_user_regs early stack deallocation is buggy in the presence of
FIQs which switch to SVC mode, and could lead to corrupted registers
being returned to a user process given an inopportune FIQ event.
Another bug was spotted in the ARM perf code where it could lose track
of perf counter overflows, leading to incorrect perf results.
Lastly, a bug in arm_add_memory() was spotted where the memory sizes
aren't properly rounded. As most people pass properly rounded sizes,
this hasn't been noticed"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8292/1: mm: fix size rounding-down of arm_add_memory() function
ARM: 8255/1: perf: Prevent wraparound during overflow
ARM: 8266/1: Remove early stack deallocation from restore_user_regs
Linus Torvalds [Fri, 23 Jan 2015 21:55:13 +0000 (09:55 +1200)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull two arm64 fixes from Will Deacon:
"Arm64 fixes seem to come in pairs recently. We've got a fix for
removing device-tree blobs when doing a make clean and another one
addressing a missing include, which fixes build failures in -next for
allmodconfig (spotted by Mark's buildbot).
Summary from signed tag:
- fix cleaning of .dtbs following directory restructuring
- fix allmodconfig build breakage in -next due to missing include"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: dump: Fix implicit inclusion of definition for PCI_IOBASE
arm64: Add dtb files to archclean rule
Joe Thornber [Fri, 23 Jan 2015 10:16:16 +0000 (10:16 +0000)]
dm cache: fix problematic dual use of a single migration count variable
Introduce a new variable to count the number of allocated migration
structures. The existing variable cache->nr_migrations became
overloaded. It was used to:
i) track of the number of migrations in flight for the purposes of
quiescing during suspend.
ii) to estimate the amount of background IO occuring.
Recent discard changes meant that REQ_DISCARD bios are processed with
a migration. Discards are not background IO so nr_migrations was not
incremented. However this could cause quiescing to complete early.
(i) is now handled with a new variable cache->nr_allocated_migrations.
cache->nr_migrations has been renamed cache->nr_io_migrations.
cleanup_migration() is now called free_io_migration(), since it
decrements that variable.
Also, remove the unused cache->next_migration variable that got replaced
with with prealloc_structs a while ago.
Signed-off-by: Joe Thornber <ejt@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Cc: stable@vger.kernel.org
Joe Thornber [Fri, 23 Jan 2015 10:00:07 +0000 (10:00 +0000)]
dm cache: share cache-metadata object across inactive and active DM tables
If a DM table is reloaded with an inactive table when the device is not
suspended (normal procedure for LVM2), then there will be two dm-bufio
objects that can diverge. This can lead to a situation where the
inactive table uses bufio to read metadata at the same time the active
table writes metadata -- resulting in the inactive table having stale
metadata buffers once it is promoted to the active table slot.
Fix this by using reference counting and a global list of cache metadata
objects to ensure there is only one metadata object per metadata device.
Signed-off-by: Joe Thornber <ejt@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Cc: stable@vger.kernel.org
Nadav Amit [Thu, 1 Jan 2015 21:11:11 +0000 (23:11 +0200)]
KVM: x86: SYSENTER emulation is broken
SYSENTER emulation is broken in several ways:
1. It misses the case of 16-bit code segments completely (CVE-2015-0239).
2. MSR_IA32_SYSENTER_CS is checked in 64-bit mode incorrectly (bits 0 and 1 can
still be set without causing #GP).
3. MSR_IA32_SYSENTER_EIP and MSR_IA32_SYSENTER_ESP are not masked in
legacy-mode.
4. There is some unneeded code.
Fix it.
Cc: stable@vger.linux.org Signed-off-by: Nadav Amit <namit@cs.technion.ac.il> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
x86/tsc: Change Fast TSC calibration failed from error to info
Many users see this message when booting without knowning that it is
of no importance and that TSC calibration may have succeeded by
another way.
As explained by Paul Bolle in
http://lkml.kernel.org/r/1348488259.1436.22.camel@x61.thuisdomein
"Fast TSC calibration failed" should not be considered as an error
since other calibration methods are being tried afterward. At most,
those send a warning if they fail (not an error). So let's change
the message from error to warning.
[ tglx: Make if pr_info. It's really not important at all ]
Bryan O'Donoghue [Thu, 22 Jan 2015 22:58:49 +0000 (22:58 +0000)]
x86/apic: Re-enable PCI_MSI support for non-SMP X86_32
Commit 0dbc6078c06bc0 ('x86, build, pci: Fix PCI_MSI build on !SMP')
introduced the dependency that X86_UP_APIC is only available when
PCI_MSI is false. This effectively prevents PCI_MSI support on 32bit
UP systems because it disables both APIC and IO-APIC. But APIC support
is architecturally required for PCI_MSI.
The intention of the patch was to enforce APIC support when PCI_MSI is
enabled, but failed to do so.
Remove the !PCI_MSI dependency from X86_UP_APIC and enforce
X86_UP_APIC when PCI_MSI support is enabled on 32bit UP systems.
[ tglx: Massaged changelog ]
Fixes 0dbc6078c06bc0 'x86, build, pci: Fix PCI_MSI build on !SMP' Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie> Suggested-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Cc: stable@vger.kernel.org Link: http://lkml.kernel.org/r/1421967529-9037-1-git-send-email-pure.logic@nexus-software.ie Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Juergen Gross [Thu, 22 Jan 2015 11:43:17 +0000 (12:43 +0100)]
x86, mm: Change cachemode exports to non-gpl
Commit 281d4078bec3 ("x86: Make page cache mode a real type")
introduced the symbols __cachemode2pte_tbl and __pte2cachemode_tbl and
exported them via EXPORT_SYMBOL_GPL. The exports are part of a
replacement of code which has been EXPORT_SYMBOL before these changes
resulting in build breakage of out-of-tree non-gpl modules.
Change EXPORT_SYMBOL_GPL to EXPORT-SYMBOL for these two symbols.
Fixes: 281d4078bec3 "x86: Make page cache mode a real type" Reported-and-tested-by: Steven Noonan <steven@uplinklabs.net> Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Toshi Kani <toshi.kani@hp.com> Link: http://lkml.kernel.org/r/1421926997-28615-1-git-send-email-jgross@suse.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Strictly speaking, this code was never correct. It should have set
read_exec_only and seg_not_present to 1 to indicate that it wanted
to find a free slot without putting anything there, or it should
have put something sensible in the TLS slot if it wanted to allocate
a TLS entry for real. The actual effect of this code was to
allocate a bogus segment that could be used to exploit espfix.
The set_thread_area hardening patches changed the behavior, causing
set_thread_area to return -EINVAL and crashing the game.
This changes set_thread_area to interpret this as a request to find
a free slot and to leave it empty, which isn't *quite* what the game
expects but should be close enough to keep it working. In
particular, using the code above to allocate two segments will
allocate the same segment both times.
According to FrostbittenKing on Github, this fixes The Witcher 2.
If this somehow still causes problems, we could instead allocate
a limit==0 32-bit data segment, but that seems rather ugly to me.
Andy Lutomirski [Thu, 22 Jan 2015 19:27:58 +0000 (11:27 -0800)]
x86, tls, ldt: Stop checking lm in LDT_empty
32-bit programs don't have an lm bit in their ABI, so they can't
reliably cause LDT_empty to return true without resorting to memset.
They shouldn't need to do this.
This should fix a longstanding, if minor, issue in all 64-bit kernels
as well as a potential regression in the TLS hardening code.
Dave Hansen [Thu, 8 Jan 2015 22:30:22 +0000 (14:30 -0800)]
x86, mpx: Strictly enforce empty prctl() args
Description from Michael Kerrisk. He suggested an identical patch
to one I had already coded up and tested.
commit fe3d197f8431 "x86, mpx: On-demand kernel allocation of bounds
tables" added two new prctl() operations, PR_MPX_ENABLE_MANAGEMENT and
PR_MPX_DISABLE_MANAGEMENT. However, no checks were included to ensure
that unused arguments are zero, as is done in many existing prctl()s
and as should be done for all new prctl()s. This patch adds the
required checks.
Suggested-by: Andy Lutomirski <luto@amacapital.net> Suggested-by: Michael Kerrisk <mtk.manpages@gmail.com> Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Cc: Dave Hansen <dave@sr71.net> Link: http://lkml.kernel.org/r/20150108223022.7F56FD13@viggo.jf.intel.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Dave Hansen [Thu, 8 Jan 2015 22:30:21 +0000 (14:30 -0800)]
x86, mpx: Fix potential performance issue on unmaps
The 3.19 merge window saw some TLB modifications merged which caused a
performance regression. They were fixed in commit 045bbb9fa.
Once that fix was applied, I also noticed that there was a small
but intermittent regression still present. It was not present
consistently enough to bisect reliably, but I'm fairly confident
that it came from (my own) MPX patches. The source was reading
a relatively unused field in the mm_struct via arch_unmap.
I also noted that this code was in the main instruction flow of
do_munmap() and probably had more icache impact than we want.
This patch does two things:
1. Adds a static (via Kconfig) and dynamic (via cpuid) check
for MPX with cpu_feature_enabled(). This keeps us from
reading that cacheline in the mm and trades it for a check
of the global CPUID variables at least on CPUs without MPX.
2. Adds an unlikely() to ensure that the MPX call ends up out
of the main instruction flow in do_munmap(). I've added
a detailed comment about why this was done and why we want
it even on systems where MPX is present.
Dave Hansen [Thu, 8 Jan 2015 22:30:20 +0000 (14:30 -0800)]
x86, mpx: Explicitly disable 32-bit MPX support on 64-bit kernels
We had originally planned on submitting MPX support in one patch
set. We eventually broke it up in to two pieces for easier
review. One of the features that didn't make the first round
was supporting 32-bit binaries on 64-bit kernels.
Once we split the set up, we never added code to restrict 32-bit
binaries from _using_ MPX on 64-bit kernels.
The 32-bit bounds tables are a different format than the 64-bit
ones. Without this patch, the kernel will try to read a 32-bit
binary's tables as if they were the 64-bit version. They will
likely be noticed as being invalid rather quickly and the app
will get killed, but that's kinda mean.
This patch adds an explicit check, and will make a 64-bit kernel
essentially behave as if it has no MPX support when called from
a 32-bit binary.
Linus Torvalds [Thu, 22 Jan 2015 18:53:06 +0000 (06:53 +1200)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Martin Schwidefsky:
"Five more bug fixes from Michael for the s390 BPF jit"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/bpf: Zero extend parameters before calling C function
s390/bpf: Fix sk_load_byte_msh()
s390/bpf: Fix offset parameter for skb_copy_bits()
s390/bpf: Fix skb_copy_bits() parameter passing
s390/bpf: Fix JMP_JGE_K (A >= K) and JMP_JGT_K (A > K)
Linus Torvalds [Thu, 22 Jan 2015 18:40:36 +0000 (06:40 +1200)]
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module and param fixes from Rusty Russell:
"Surprising number of fixes this merge window :(
The first two are minor fallout from the param rework which went in
this merge window.
The next three are a series which fixes a longstanding (but never
previously reported and unlikely , so no CC stable) race between
kallsyms and freeing the init section.
Finally, a minor cleanup as our module refcount will now be -1 during
unload"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
module: make module_refcount() a signed integer.
module: fix race in kallsyms resolution during module load success.
module: remove mod arg from module_free, rename module_memfree().
module_arch_freeing_init(): new hook for archs before module->module_init freed.
param: fix uninitialized read with CONFIG_DEBUG_LOCK_ALLOC
param: initialize store function to NULL if not available.
Colin Ian King [Thu, 22 Jan 2015 11:20:40 +0000 (11:20 +0000)]
scsi_debug: test always evaluates to false, || should be used instead
cppcheck found the following issue:
(warning) Logical conjunction always evaluates to false:
alloc_len < 4 && alloc_len > 65535.
..the test should be instead:
if (alloc_len < 4 || alloc_len > 65536)
This error was introduced by recent commit 38d5c8336e60bf6e53a1da9
("scsi_debug: add Report supported opcodes+tmfs; Compare and write")
Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: Douglas Gilbert <dgilbert@interlog.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
of/platform: Handle of_populate drivers in notifier
When using overlays with drivers calling of_populate the notifier
will try to create the device twice. Using the populated bit
before proceeding protects against this.
Signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com> Signed-off-by: Grant Likely <grant.likely@linaro.org>
Olof Johansson [Thu, 22 Jan 2015 01:15:49 +0000 (17:15 -0800)]
Merge tag 'renesas-soc-fixes2-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
Merge "Second Round of Renesas ARM Based SoC Fixes for v3.19" from Simon
Horman:
* Instantiate GIC from C board code in legacy builds on r8a7778 and r8a7779
* tag 'renesas-soc-fixes2-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7779: Instantiate GIC from C board code in legacy builds
ARM: shmobile: r8a7778: Instantiate GIC from C board code in legacy builds
Rusty Russell [Thu, 22 Jan 2015 00:43:14 +0000 (11:13 +1030)]
module: make module_refcount() a signed integer.
James Bottomley points out that it will be -1 during unload. It's
only used for diagnostics, so let's not hide that as it could be a
clue as to what's gone wrong.
Cc: Jason Wessel <jason.wessel@windriver.com> Acked-and-documention-added-by: James Bottomley <James.Bottomley@HansenPartnership.com> Reviewed-by: Masami Hiramatsu <maasami.hiramatsu.pt@hitachi.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Sakari Ailus [Thu, 1 Jan 2015 21:13:54 +0000 (18:13 -0300)]
[media] omap3isp: Correctly set QUERYCAP capabilities
device_caps in struct v4l2_capability were inadequately set in
VIDIOC_QUERYCAP. Fix this. Without this a WARN_ON in the v4l2 core
is triggered. This WARN_ON was added for kernel 3.19 exactly to
detect these situations.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
projects / mirror_ubuntu-jammy-kernel.git / log