Thomas Petazzoni [Fri, 21 Dec 2012 14:49:19 +0000 (15:49 +0100)]
arm: mvebu: enable btmrvl driver in mvebu_defconfig
The Globalscale Mirabox platform, based on the Armada 370 from
Marvell, has a SD8787 Wireless/Bluetooth chip connected on the SDIO
interface. Now that the mvsdio has a Device Tree binding, and the
necessary Device Tree informations have been added at the SoC and
board level, let's enable the btmrvl driver for the Bluetooth part of
the SD8787 chip.
For now, the driver gets probed correctly, detects the device but
apparently fails to push the firmware to the device:
Bluetooth: vendor=0x2df, device=0x911a, class=255, fn=2
Bluetooth: FW failed to be active in time!
Bluetooth: Downloading firmware failed!
Bluetooth: vendor=0x2df, device=0x911b, class=255, fn=3
Bluetooth: FW failed to be active in time!
Bluetooth: Downloading firmware failed!
This will have to be investigated separately.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Fri, 21 Dec 2012 14:49:18 +0000 (15:49 +0100)]
arm: mvebu: enable mwifiex driver in mvebu_defconfig
The Globalscale Mirabox platform, based on the Armada 370 from
Marvell, has a SD8787 Wireless chip connected on the SDIO
interface. Now that the mvsdio has a Device Tree binding, and the
necessary Device Tree informations have been added at the SoC and
board level, let's enable the mwifiex driver for the Wireless part of
the SD8787 chip.
For now, the driver gets probed correctly, detects a device and shows
the network interfaces. However, scanning Wifi networks doesn't work
for now, with a 'CMD_RESP: cmd 0x6 error, result=0x1' message. This
will have to be investigated separately.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Fri, 21 Dec 2012 14:49:17 +0000 (15:49 +0100)]
arm: mvebu: enable SDIO support in mvebu_defconfig
Now that the mvsdio driver has gained Device Tree support and the
necessary Device Tree informations has been added for Armada 370 and
Armada XP platforms, we enable the MMC subsystem and the mvsdio driver
in mvebu_defconfig.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Gregory CLEMENT [Wed, 12 Dec 2012 09:06:26 +0000 (10:06 +0100)]
arm: mvebu: Update defconfig with Marvell RTC support
The RTC class driver is already part of the mvebu_defconfig but the
Marvell internal RTC not yet. Now that its support is added for mvebu
let's update the config file.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Tested-by: Florian Fainelli <florian@openwrt.org> Acked-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Mon, 28 Jan 2013 11:26:53 +0000 (06:26 -0500)]
mmc: mvsdio: add pinctrl integration
On many Marvell SoCs, the pins used for the SDIO interface are part of
the MPP pins, that are muxable pins. In order to get the muxing of
those pins correct, this commit integrates the mvsdio driver with the
pinctrl infrastructure by calling devm_pinctrl_get_select_default()
during ->probe().
Note that we permit this function to fail because not all Marvell
platforms have yet been fully converted to using the pinctrl
infrastructure.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Stefan Peter <s.peter@mpl.ch> Tested-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: Jason Cooper <jason@lakedaemon.net> Signed-off-by: Chris Ball <cjb@laptop.org>
Thomas Petazzoni [Wed, 16 Jan 2013 13:13:59 +0000 (14:13 +0100)]
mmc: mvsdio: implement a Device Tree binding
This patch adds a simple Device Tree binding for the mvsdio driver, as
well as the necessary documentation for it. Compatibility with non-DT
platforms is preserved, by keeping the platform_data based
initialization.
We introduce a small difference between non-DT and DT platforms: DT
platforms are required to provide a clocks = <...> property, which the
driver uses to get the frequency of the clock that goes to the SDIO
IP. The behaviour on non-DT platforms is kept unchanged: a clock
reference is not mandatory, but the clock frequency must be passed in
the "clock" field of the mvsdio_platform_data structure.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Stefan Peter <s.peter@mpl.ch> Tested-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: Jason Cooper <jason@lakedaemon.net> Signed-off-by: Chris Ball <cjb@laptop.org>
Thomas Petazzoni [Wed, 16 Jan 2013 13:13:58 +0000 (14:13 +0100)]
mmc: mvsdio: use slot-gpio for card detect gpio
The MMC core subsystem provides in drivers/mmc/core/slot-gpio.c a nice
set of helper functions to simplify the management of the card detect
GPIO in MMC host drivers. This patch migrates the mvsdio driver to
using those helpers, which will make the ->probe() code simpler, and
therefore ease the process of adding a Device Tree binding for this
driver.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Stefan Peter <s.peter@mpl.ch> Tested-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: Jason Cooper <jason@lakedaemon.net> Signed-off-by: Chris Ball <cjb@laptop.org>
Thomas Petazzoni [Wed, 16 Jan 2013 13:13:57 +0000 (14:13 +0100)]
mmc: mvsdio: use slot-gpio infrastructure for write protect gpio
The MMC core subsystem provides in drivers/mmc/core/slot-gpio.c a nice
set of helper functions to simplify the management of the write
protect GPIO in MMC host drivers. This patch migrates the mvsdio
driver to using those helpers, which will make the ->probe() code
simpler, and therefore ease the process of adding a Device Tree
binding for this driver.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Stefan Peter <s.peter@mpl.ch> Tested-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: Jason Cooper <jason@lakedaemon.net> Signed-off-by: Chris Ball <cjb@laptop.org>
Shawn Guo [Tue, 15 Jan 2013 15:19:54 +0000 (23:19 +0800)]
mmc: sdhci-esdhc-imx: remove ESDHC_CD_GPIO handling from IO accessory
With commit 9444e07 (mmc: remove unncessary mmc_gpio_free_cd() call from
slot-gpio users) in place, the ESDHC_CD_GPIO handling in IO accessories
becomes unnecessary. Remove it.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Chris Ball <cjb@laptop.org>
Kevin Liu [Sat, 5 Jan 2013 09:18:28 +0000 (17:18 +0800)]
mmc: sdhci: disable interrupt before free_irq
Current code missed disabling interrupts before free irq which is shared.
Notice below comments for function free_irq (kernel/irq/manage.c):
On a shared IRQ the caller must ensure the interrupt is disabled
on the card it drives before calling this function.
Original code has below issue during suspend/resume when multiple SD
hosts share the same IRQ:
1. Assume there are two hosts (host1 for emmc while host2 for sd) share
the same mmc irq.
2. When system suspend, host2 will be suspended before host1.
So the sequence is below:
step1: irq handler for host2 removed ->
step2: irq handler for host1 removed and irq disabled ->
... system suspended ...
... system resumed ...
step3: irq enabled and the irq handler for host1 restored ->
step4: irq handler for host2 restored
3. So there is the buggy time slot that the irq is enabled but the irq
handler for host2 is removed. Then host2 interrupt can be triggered
but can't be handled at that moment.
Signed-off-by: Jialing Fu <jlfu@marvell.com> Signed-off-by: Kevin Liu <kliu5@marvell.com> Signed-off-by: Chris Ball <cjb@laptop.org>
mmc: fix async request mechanism for sequential read scenarios
When current request is running on the bus and if next request fetched
by mmcqd is NULL, mmc context (mmcqd thread) gets blocked until the
current request completes. This means that if new request comes in while
the mmcqd thread is blocked, this new request can not be prepared in
parallel to current ongoing request. This may result in delaying the new
request execution and increase it's latency.
This change allows to wake up the MMC thread on new request arrival.
Now once the MMC thread is woken up, a new request can be fetched and
prepared in parallel to the current running request which means this new
request can be started immediately after the current running request
completes.
With this change read throughput is improved by 16%.
Signed-off-by: Konstantin Dorfman <kdorfman@codeaurora.org> Reviewed-by: Seungwon Jeon <tgih.jun@samsung.com> Signed-off-by: Chris Ball <cjb@laptop.org>
The classical way to process IRQs is read out the status, ack all triggered
IRQs, possibly mask them, then process them. Follow this simple procesure
instead of the current complex custom algorithm.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: Chris Ball <cjb@laptop.org>
Teppei Kamijou [Wed, 12 Dec 2012 14:38:18 +0000 (15:38 +0100)]
mmc: sh_mmcif: report all errors
Make error reporting in the driver more verbose. This patch is based on
an earlier work by Teppei Kamijou, but we try to not add any new error
messages to the log in the normal case to avoid confusing the user, and
also add a few more dev_dbg() calls.
Signed-off-by: Teppei Kamijou <teppei.kamijou.yb@renesas.com> Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
[g.liakhovetski@gmx.de: avoid producing new errors in normal case] Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: Chris Ball <cjb@laptop.org>
The INT_BUFWEN IRQ often arrives with other bits set too. If they are not
cleared, an additional IRQ can be triggered, sometimes also after the MMC
request has already been completed. This leads to block I/O errors. Earlier
Teppei Kamijou also observed these additional interrupts and proposed to
explicitly wait for them. This patch chooses an alternative approach of
clearing all active bits immediately, when processing the main interrupt.
mmc: sh_mmcif: reset DMA completion immediately before starting DMA
DMA completion can be signalled from the DMA callback and from the error
handler. If both are called, the completion struct can enter an
inconsistent state. To prevent this move completion initialisation
immediately before activating DMA.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: Chris Ball <cjb@laptop.org>
Oopses have been observed on SMP in the sh-mmcif IRQ thread, when the two
IRQ threads run simultaneously on two CPUs. Also take care to guard the
timeout work and the DMA completion callback from possible NULL-pointer
dereferences and races.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: Chris Ball <cjb@laptop.org>
Teppei Kamijou [Wed, 12 Dec 2012 14:38:10 +0000 (15:38 +0100)]
mmc: sh_mmcif: Avoid unnecessary mmc_delay() at mmc_card_sleepawake()
SH/R-Mobile MMCIF host controller can wait while the card signals busy.
Set MMC_CAP_WAIT_WHILE_BUSY to inform an upper layer (core/mmc_ops.c)
not to insert unnecessary mmc_delay().
Teppei Kamijou [Wed, 12 Dec 2012 14:38:08 +0000 (15:38 +0100)]
mmc: sh_mmcif: Add support for eMMC Dual Data Rate
Some MMCIF implementations support the Dual Data Rate. With this patch,
platforms can set the MMC_CAP_UHS_DDR50 capability flag in MMCIF platform
data. This will let the MMC core to actually use the DDR mode.
Teppei Kamijou [Wed, 12 Dec 2012 14:38:05 +0000 (15:38 +0100)]
mmc: sh_mmcif: force to fail CMD52 immediately
mmc_rescan() sends CMD52 (SD_IO_RW_DIRECT) to reset SDIO card during
card detection. CMD52 should be ignored by SD/eMMC cards, but we can
also abort it in the driver immediately, since MMCIF doesn't support
SDIO cards anyway.
Shawn Guo [Tue, 11 Dec 2012 14:32:19 +0000 (22:32 +0800)]
mmc: remove unncessary mmc_gpio_free_cd() call from slot-gpio users
Since slot-gpio uses devm_* managed functions in mmc_gpio_request_cd()
now, we can remove those mmc_gpio_free_cd() call from host drivers'
.probe() error path and .remove().
Shawn Guo [Tue, 11 Dec 2012 14:32:18 +0000 (22:32 +0800)]
mmc: slot-gpio: use devm_* managed functions to ease users
Use devm_* managed functions, so that slot-gpio users do not have to
call mmc_gpio_free_ro/cd to free up resources requested in
mmc_gpio_request_ro/cd.
Shawn Guo [Tue, 11 Dec 2012 07:23:42 +0000 (15:23 +0800)]
mmc: sdhci: query card presence from cd-gpio before asking SDHCI
Call mmc_gpio_get_cd() to query card presence from cd-gpio before
asking SDHCI. The rationale behind this change is that flag
SDHCI_QUIRK_BROKEN_CARD_DETECTION is designed for SDHCI controller to
tell that SDHCI_PRESENT_STATE is broken, and it should be used for this
case only. So when cd-gpio is being used, the controller should set
the flag to tell that SDHCI_PRESENT_STATE is not available.
However, the existing code will skip checking cd-gpio as long as flag
SDHCI_QUIRK_BROKEN_CARD_DETECTION is set. Change the querying order
between cd-gpio and SDHCI to support the rationale above.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Chris Ball <cjb@laptop.org>
According to UHS-I initialization sequence for SDIO 3.0 cards,
the host must set bit[24] (S18R) of OCR register during OCR
handshake to know whether the SDIO card is capable of doing
1.8V I/O.
mmc: sdio: fix resume failure due to lack of CMD52 reset
If SDIO keep power flag (MMC_PM_KEEP_POWER) is not set, card would
be reinitialized during resume but as we are not resetting
(CMD52 reset) the SDIO card during this reinitialization, card may
fail to respond back to subsequent commands (CMD5 etc...).
This change resets the card before the reinitialization of card
during resume.
Linus Torvalds [Thu, 31 Jan 2013 21:44:59 +0000 (08:44 +1100)]
Merge branch 'for-3.8/upstream-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
PullHID fixes from Jiri Kosina:
- fix i2c-hid and hidraw interaction, by Benjamin Tissoires
- a quirk to make a particular device (Formosa IR receiver) work
properly, by Nicholas Santos
* 'for-3.8/upstream-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: i2c-hid: fix i2c_hid_output_raw_report
HID: usbhid: quirk for Formosa IR receiver
HID: remove x bit from sensor doc
Linus Torvalds [Thu, 31 Jan 2013 21:43:52 +0000 (08:43 +1100)]
Merge tag 'nfs-for-3.8-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
- Error reporting in nfs_xdev_mount incorrectly maps all errors to
ENOMEM
- Fix an NFSv4 refcounting issue
- Fix a mount failure when the server reboots during NFSv4 trunking
discovery
- NFSv4.1 mounts may need to run the lease recovery thread.
- Don't silently fail setattr() requests on mountpoints
- Fix a SUNRPC socket/transport livelock and priority queue issue
- We must handle NFS4ERR_DELAY when resetting the NFSv4.1 session.
* tag 'nfs-for-3.8-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFSv4.1: Handle NFS4ERR_DELAY when resetting the NFSv4.1 session
SUNRPC: When changing the queue priority, ensure that we change the owner
NFS: Don't silently fail setattr() requests on mountpoints
NFSv4.1: Ensure that nfs41_walk_client_list() does start lease recovery
NFSv4: Fix NFSv4 trunking discovery
NFSv4: Fix NFSv4 reference counting for trunked sessions
NFS: Fix error reporting in nfs_xdev_mount
Linus Torvalds [Thu, 31 Jan 2013 21:43:04 +0000 (08:43 +1100)]
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS updates from Ralf Baechle:
"A number of fixes all across the MIPS tree. No area is particularly
standing out and things have cooled down quite nicely for a release."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Function tracer: Fix broken function tracing
mips: Move __virt_addr_valid() to a place for MIPS 64
MIPS: Netlogic: Fix UP compilation on XLR
MIPS: AR71xx: Fix AR71XX_PCI_MEM_SIZE
MIPS: AR724x: Fix AR724X_PCI_MEM_SIZE
MIPS: Lantiq: Fix cp0_perfcount_irq mapping
MIPS: DSP: Fix DSP mask for registers.
MIPS: Fix build failure by adding definition of pfn_pmd().
MIPS: Octeon: Fix warning.
MIPS: delay.c: Check BITS_PER_LONG instead of __SIZEOF_LONG__
MIPS: PNX833x: Fix comment.
MIPS: Add struct p_format to union mips_instruction.
MIPS: Export <asm/break.h>.
MIPS: BCM47xx: Enable SSB prerequisite SSB_DRIVER_PCICORE.
MIPS: BCM47xx: Select GPIOLIB for BCMA on bcm47xx platform
MIPS: vpe.c: Fix null pointer dereference in print arguments.
Jason Cooper [Thu, 31 Jan 2013 17:38:25 +0000 (17:38 +0000)]
Merge tag 'tags/mvebu_fixes_for_v3.8-rc6' into mvebu/boards
fixes for v3.8-rc6
- add missing gpio interrupt lines to dove dt
- fix bad logic for printing MPP error message on orion boards
- build proper serial port driver after changing mvebu DT compatible property
- This is a change to mvebu_defconfig that I wouldn't usually push out as a
fix. However, the commit
b24212f arm: mvebu: Use dw-apb-uart instead of ns16650 as UART driver
changed the serial driver for the board in the dts file. without the patch
I've included in this pull, users won't see any log messages.
i2c_hid_output_raw_report is used by hidraw to forward set_report requests.
The current implementation of i2c_hid_set_report needs to take the
report_id as an argument. The report_id is stored in the first byte
of the buffer in argument of i2c_hid_output_raw_report.
Not removing the report_id from the given buffer adds this byte 2 times
in the command, leading to a non working command.
Reported-by: Andrew Duggan <aduggan@synaptics.com> Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Al Cooper [Wed, 16 Jan 2013 22:43:28 +0000 (22:43 +0000)]
MIPS: Function tracer: Fix broken function tracing
Function tracing is currently broken for all 32 bit MIPS platforms.
When tracing is enabled, the kernel immediately hangs on boot.
This is a result of commit b732d439cb43336cd6d7e804ecb2c81193ef63b0
that changes the kernel/trace/Kconfig file so that is no longer
forces FRAME_POINTER when FUNCTION_TRACING is enabled.
MIPS frame pointers are generally considered to be useless because
they cannot be used to unwind the stack. Unfortunately the MIPS
function tracing code has bugs that are masked by the use of frame
pointers. This commit fixes the bugs so that MIPS frame pointers
don't need to be enabled.
The bugs are a result of the odd calling sequence used to call the trace
routine. This calling sequence is inserted into every traceable function
when the tracing CONFIG option is enabled. This sequence is generated
for 32bit MIPS platforms by the compiler via the "-pg" flag.
Part of the sequence is "addiu sp,sp,-8" in the delay slot after every
call to the trace routine "_mcount" (some legacy thing where 2 arguments
used to be pushed on the stack). The _mcount routine is expected to
adjust the sp by +8 before returning. So when not disabled, the original
jalr and addiu will be there, so _mcount has to adjust sp.
The problem is that when tracing is disabled for a function, the
"jalr _mcount" instruction is replaced with a nop, but the
"addiu sp,sp,-8" is still executed and the stack pointer is left
trashed. When frame pointers are enabled the problem is masked
because any access to the stack is done through the frame
pointer and the stack pointer is restored from the frame pointer when
the function returns.
This patch writes two nops starting at the address of the "jalr _mcount"
instruction whenever tracing is disabled. This means that the
"addiu sp,sp.-8" will be converted to a nop along with the "jalr". When
disabled, there will be two nops.
This is SMP safe because the first time this happens is during
ftrace_init() which is before any other processor has been started.
Subsequent calls to enable/disable tracing when other CPUs ARE running
will still be safe because the enable will only change the first nop
to a "jalr" and the disable, while writing 2 nops, will only be changing
the "jalr". This patch also stops using stop_machine() to call the
tracer enable/disable routines and calls them directly because the
routines are SMP safe.
When the kernel first boots we have to be able to handle the gcc
generated jalr, addui sequence until ftrace_init gets a chance to run
and change the sequence. At this point mcount just adjusts the stack
and returns. When ftrace_init runs, we convert the jalr/addui to nops.
Then whenever tracing is enabled we convert the first nop to a "jalr
mcount+8". The mcount+8 entry point skips the stack adjust.
[ralf@linux-mips.org: Folded in Steven Rostedt's build fix.]
Signed-off-by: Al Cooper <alcooperx@gmail.com> Cc: rostedt@goodmis.org Cc: ddaney.cavm@gmail.com Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/4806/
Patchwork: https://patchwork.linux-mips.org/patch/4841/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When processing write same requests, fix dm to send the configured
number of WRITE SAME requests to the target rather than the number of
discards, which is not always the same.
Steven Rostedt [Fri, 25 Jan 2013 17:13:15 +0000 (17:13 +0000)]
mips: Move __virt_addr_valid() to a place for MIPS 64
Commit d3ce88431892 "MIPS: Fix modpost error in modules attepting to use
virt_addr_valid()" moved __virt_addr_valid() from a macro in a header
file to a function in ioremap.c. But ioremap.c is only compiled for MIPS
32, and not for MIPS 64.
When compiling for my yeeloong2, which supposedly supports hibernation,
which compiles kernel/power/snapshot.c which calls virt_addr_valid(), I
got this error:
LD init/built-in.o
kernel/built-in.o: In function `memory_bm_free':
snapshot.c:(.text+0x4c9c4): undefined reference to `__virt_addr_valid'
snapshot.c:(.text+0x4ca58): undefined reference to `__virt_addr_valid'
kernel/built-in.o: In function `snapshot_write_next':
(.text+0x4e44c): undefined reference to `__virt_addr_valid'
kernel/built-in.o: In function `snapshot_write_next':
(.text+0x4e890): undefined reference to `__virt_addr_valid'
make[1]: *** [vmlinux] Error 1
make: *** [sub-make] Error 2
I suspect that __virt_addr_valid() is fine for mips 64. I moved it to
mmap.c such that it gets compiled for mips 64 and 32.
Mike Snitzer [Thu, 31 Jan 2013 14:11:14 +0000 (14:11 +0000)]
dm thin: fix queue limits stacking
thin_io_hints() is blindly copying the queue limits from the thin-pool
which can lead to incorrect limits being set. The fix here simply
deletes the thin_io_hints() hook which leaves the existing stacking
infrastructure to set the limits correctly.
When a thin-pool uses an MD device for the data device a thin device
from the thin-pool must respect MD's constraints about disallowing a bio
from spanning multiple chunks. Otherwise we can see problems. If the raid0
chunksize is 1152K and thin-pool chunksize is 256K I see the following
md/raid0 error (with extra debug tracing added to thin_endio) when
mkfs.xfs is executed against the thin device:
md/raid0:md99: make_request bug: can't convert block across chunks or bigger than 1152k 6688 127
device-mapper: thin: bio sector=2080 err=-5 bi_size=130560 bi_rw=17 bi_vcnt=32 bi_idx=0
This extra DM debugging shows that the failing bio is spanning across
the first and second logical 1152K chunk (sector 2080 + 255 takes the
bio beyond the first chunk's boundary of sector 2304). So the bio
splitting that DM is doing clearly isn't respecting the MD limits.
max_hw_sectors_kb is 127 for both the thin-pool and thin device
(queue_max_hw_sectors returns 255 so we'll excuse sysfs's lack of
precision). So this explains why bi_size is 130560.
But the thin device's max_hw_sectors_kb should be 4 (PAGE_SIZE) given
that it doesn't have a .merge function (for bio_add_page to consult
indirectly via dm_merge_bvec) yet the thin-pool does sit above an MD
device that has a compulsory merge_bvec_fn. This scenario is exactly
why DM must resort to sending single PAGE_SIZE bios to the underlying
layer. Some additional context for this is available in the header for
commit 8cbeb67a ("dm: avoid unsupported spanning of md stripe boundaries").
Long story short, the reason a thin device doesn't properly get
configured to have a max_hw_sectors_kb of 4 (PAGE_SIZE) is that
thin_io_hints() is blindly copying the queue limits from the thin-pool
device directly to the thin device's queue limits.
Fix this by eliminating thin_io_hints. Doing so is safe because the
block layer's queue limits stacking already enables the upper level thin
device to inherit the thin-pool device's discard and minimum_io_size and
optimal_io_size limits that get set in pool_io_hints. But avoiding the
queue limits copy allows the thin and thin-pool limits to be different
where it is important, namely max_hw_sectors_kb.
Reported-by: Daniel Browning <db@kavod.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Linus Torvalds [Thu, 31 Jan 2013 06:10:36 +0000 (17:10 +1100)]
Merge branch 'x86-efi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 EFI fixes from Peter Anvin:
"This is a collection of fixes for the EFI support. The controversial
bit here is a set of patches which bumps the boot protocol version as
part of fixing some serious problems with the EFI handover protocol,
used when booting under EFI using a bootloader as opposed to directly
from EFI. These changes should also make it a lot saner to support
cross-mode 32/64-bit EFI booting in the future. Getting these changes
into 3.8 means we avoid presenting an inconsistent ABI to bootloaders.
Other changes are display detection and fixing efivarfs."
* 'x86-efi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, efi: remove attribute check from setup_efi_pci
x86, build: Dynamically find entry points in compressed startup code
x86, efi: Fix PCI ROM handing in EFI boot stub, in 32-bit mode
x86, efi: Fix 32-bit EFI handover protocol entry point
x86, efi: Fix display detection in EFI boot stub
x86, boot: Define the 2.12 bzImage boot protocol
x86/boot: Fix minor fd leakage in tools/relocs.c
x86, efi: Set runtime_version to the EFI spec revision
x86, efi: fix 32-bit warnings in setup_efi_pci()
efivarfs: Delete dentry from dcache in efivarfs_file_write()
efivarfs: Never return ENOENT from firmware
efi, x86: Pass a proper identity mapping in efi_call_phys_prelog
efivarfs: Drop link count of the right inode
Linus Torvalds [Thu, 31 Jan 2013 06:08:43 +0000 (17:08 +1100)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Peter Anvin:
"This is a collection of miscellaneous fixes, the most important one is
the fix for the Samsung laptop bricking issue (auto-blacklisting the
samsung-laptop driver); the efi_enabled() changes you see below are
prerequisites for that fix.
The other issues fixed are booting on OLPC XO-1.5, an UV fix, NMI
debugging, and requiring CAP_SYS_RAWIO for MSR references, just as
with I/O port references."
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
samsung-laptop: Disable on EFI hardware
efi: Make 'efi_enabled' a function to query EFI facilities
smp: Fix SMP function call empty cpu mask race
x86/msr: Add capabilities check
x86/dma-debug: Bump PREALLOC_DMA_DEBUG_ENTRIES
x86/olpc: Fix olpc-xo1-sci.c build errors
arch/x86/platform/uv: Fix incorrect tlb flush all issue
x86-64: Fix unwind annotations in recent NMI changes
x86-32: Start out cr0 clean, disable paging before modifying cr3/4
Linus Torvalds [Thu, 31 Jan 2013 06:04:46 +0000 (17:04 +1100)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull console lockdep checking revert from Dave Airlie.
The lockdep splat this showed was interesting, but it's very very old,
and we won't be fixing it until 3.9. In the meantime, undo the lockdep
annotation so that we don't generate the (known) console lockdep issue,
and then possibly hide any potential other (unknown) lockdep problems
that got disabled by the first one that triggered.
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
Revert "console: implement lockdep support for console_lock"
Trond Myklebust [Wed, 30 Jan 2013 18:04:10 +0000 (13:04 -0500)]
NFSv4.1: Handle NFS4ERR_DELAY when resetting the NFSv4.1 session
NFS4ERR_DELAY is a legal reply when we call DESTROY_SESSION. It
usually means that the server is busy handling an unfinished RPC
request. Just sleep for a second and then retry.
We also need to be able to handle the NFS4ERR_BACK_CHAN_BUSY return
value. If the NFS server has outstanding callbacks, we just want to
similarly sleep & retry.
Trond Myklebust [Sun, 27 Jan 2013 19:20:49 +0000 (14:20 -0500)]
SUNRPC: When changing the queue priority, ensure that we change the owner
This fixes a livelock in the xprt->sending queue where we end up never
making progress on lower priority tasks because sleep_on_priority()
keeps adding new tasks with the same owner to the head of the queue,
and priority bumps mean that we keep resetting the queue->owner to
whatever task is at the head of the queue.
H. Peter Anvin [Wed, 30 Jan 2013 22:43:05 +0000 (14:43 -0800)]
Merge tag 'efi-for-3.8' into x86/efi
Various urgent EFI fixes and some warning cleanups for v3.8
* EFI boot stub fix for Macbook Pro's from Maarten Lankhorst
* Fix an oops in efivarfs from Lingzhu Xiang
* 32-bit warning cleanups from Jan Beulich
* Patch to Boot on >512GB RAM systems from Nathan Zimmer
* Set efi.runtime_version correctly
* efivarfs updates
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Trond Myklebust [Tue, 22 Jan 2013 05:17:06 +0000 (00:17 -0500)]
NFS: Don't silently fail setattr() requests on mountpoints
Ensure that any setattr and getattr requests for junctions and/or
mountpoints are sent to the server. Ever since commit 0ec26fd0698 (vfs: automount should ignore LOOKUP_FOLLOW), we have
silently dropped any setattr requests to a server-side mountpoint.
For referrals, we have silently dropped both getattr and setattr
requests.
This patch restores the original behaviour for setattr on mountpoints,
and tries to do the same for referrals, provided that we have a
filehandle...
Gabor Juhos [Tue, 29 Jan 2013 08:27:04 +0000 (08:27 +0000)]
MIPS: AR71xx: Fix AR71XX_PCI_MEM_SIZE
The base address of the PCI memory is 0x10000000 and the base address of the
PCI configuration space is 0x17000000 on the AR71xx SoCs.
The AR71XX_PCI_MEM_SIZE is defined as 0x08000000 which is wrong because that
overlaps with the configuration space. This patch fixes the value of the
AR71XX_PCI_MEM_SIZE constant, in order to avoid this resource conflicts.
Gregory CLEMENT [Wed, 12 Dec 2012 09:06:23 +0000 (10:06 +0100)]
rtc: Add support of rtc-mv for MVEBU SoCs
The Armada 370 and Armada XP Socs have the same controller that the
one used in the orion platforms. This patch enables the selection of
rtc-mv with mvebu platforms.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Acked-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Florian Fainelli <florian@openwrt.org> Acked-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Jason Gunthorpe [Wed, 21 Nov 2012 18:25:28 +0000 (11:25 -0700)]
ARM: Kirkwood: Support basic hotplug for PCI-E
Unconditionally register the PCI-E bus, even if the link is currently
down. When the link is brought up the bus can be scanned through
/sys/bus/pci/rescan or otherwise. Since the HW has no interrupt for
link up, userspace will have to take care of the timing.
An earlier version of this was contingent on CONFIG_HOTPLUG, but
that is being removed from the kernel.
This also fixes printing the link up/down message to be displayed
on one line (structured logging broke this?)
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Jason Cooper [Wed, 30 Jan 2013 20:12:25 +0000 (20:12 +0000)]
Merge tag 'tags/mvebu_fixes_for_v3.8-rc6' into mvebu/drivers
fixes for v3.8-rc6
- add missing gpio interrupt lines to dove dt
- fix bad logic for printing MPP error message on orion boards
- build proper serial port driver after changing mvebu DT compatible property
- This is a change to mvebu_defconfig that I wouldn't usually push out as a
fix. However, the commit
b24212f arm: mvebu: Use dw-apb-uart instead of ns16650 as UART driver
changed the serial driver for the board in the dts file. without the patch
I've included in this pull, users won't see any log messages.
Matt Fleming [Thu, 3 Jan 2013 09:02:37 +0000 (09:02 +0000)]
samsung-laptop: Disable on EFI hardware
It has been reported that running this driver on some Samsung laptops
with EFI can cause those machines to become bricked as detailed in the
following report,
There have also been reports of this driver causing Machine Check
Exceptions on recent EFI-enabled Samsung laptops,
https://bugzilla.kernel.org/show_bug.cgi?id=47121
So disable it if booting from EFI since this driver relies on
grovelling around in the BIOS memory map which isn't going to work.
Cc: Corentin Chary <corentincj@iksaif.net> Cc: Matthew Garrett <mjg59@srcf.ucam.org> Cc: Colin Ian King <colin.king@canonical.com> Cc: Steve Langasek <steve.langasek@canonical.com> Cc: <stable@vger.kernel.org> Signed-off-by: Matt Fleming <matt.fleming@intel.com> Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Matt Fleming [Wed, 14 Nov 2012 09:42:35 +0000 (09:42 +0000)]
efi: Make 'efi_enabled' a function to query EFI facilities
Originally 'efi_enabled' indicated whether a kernel was booted from
EFI firmware. Over time its semantics have changed, and it now
indicates whether or not we are booted on an EFI machine with
bit-native firmware, e.g. 64-bit kernel with 64-bit firmware.
The immediate motivation for this patch is the bug report at,
which details how running a platform driver on an EFI machine that is
designed to run under BIOS can cause the machine to become
bricked. Also, the following report,
https://bugzilla.kernel.org/show_bug.cgi?id=47121
details how running said driver can also cause Machine Check
Exceptions. Drivers need a new means of detecting whether they're
running on an EFI machine, as sadly the expression,
if (!efi_enabled)
hasn't been a sufficient condition for quite some time.
Users actually want to query 'efi_enabled' for different reasons -
what they really want access to is the list of available EFI
facilities.
For instance, the x86 reboot code needs to know whether it can invoke
the ResetSystem() function provided by the EFI runtime services, while
the ACPI OSL code wants to know whether the EFI config tables were
mapped successfully. There are also checks in some of the platform
driver code to simply see if they're running on an EFI machine (which
would make it a bad idea to do BIOS-y things).
This patch is a prereq for the samsung-laptop fix patch.
Cc: David Airlie <airlied@linux.ie> Cc: Corentin Chary <corentincj@iksaif.net> Cc: Matthew Garrett <mjg59@srcf.ucam.org> Cc: Dave Jiang <dave.jiang@intel.com> Cc: Olof Johansson <olof@lixom.net> Cc: Peter Jones <pjones@redhat.com> Cc: Colin Ian King <colin.king@canonical.com> Cc: Steve Langasek <steve.langasek@canonical.com> Cc: Tony Luck <tony.luck@intel.com> Cc: Konrad Rzeszutek Wilk <konrad@kernel.org> Cc: Rafael J. Wysocki <rjw@sisk.pl> Cc: <stable@vger.kernel.org> Signed-off-by: Matt Fleming <matt.fleming@intel.com> Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Linus Torvalds [Wed, 30 Jan 2013 11:32:48 +0000 (22:32 +1100)]
Merge tag 'edac_for_3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp
Pull EDAC fixlets from Borislav Petkov:
"Two minor correctness fixlets from Dan Carpenter and Joe Perches each."
* tag 'edac_for_3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
EDAC: Fix kcalloc argument order
EDAC: Test correct variable in ->store function
Linus Torvalds [Wed, 30 Jan 2013 11:20:48 +0000 (22:20 +1100)]
Merge tag 'sound-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
- A collection of small ASoC driver fixes (error path fixes, register
correction, regulator bypass mode fix, etc)
- A few regression fixes and quirks of HD-audio (wrong page attributes
for SG-buffer, Poulsbo/Oaktrail controller fix, digital mic fix for
Acer, etc)
- A fix for USB-audio UAC2 devices wrt FU length check
* tag 'sound-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Fix non-snoop page handling
ALSA: hda - Enable LPIB delay count for Poulsbo / Oaktrail
ALSA: hda - fix inverted internal mic on Acer AOA150/ZG5
ALSA: usb-audio: fix invalid length check for RME and other UAC 2 devices
ALSA: hda - Add a fixup for Packard-Bell desktop with ALC880
ASoC: wm_adsp: Release firmware on error
ASoC: wm_adsp: Use GFP_DMA for things that may be DMAed
ASoC: arizona: Use actual rather than desired BCLK when calculating LRCLK
ASoC: wm2200: correct mixer values and text
ASoC: MAINTAINERS: Update email address.
ASoC: wm5110: Correct AEC loopback mask
ASoC: wm5102: Correct AEC loopback mask
ASoC: dapm: Fix sense of regulator bypass mode
ASoC: fsl: fix multiple definition of init_module
ASoC: arizona: Disable free-running mode on FLL1
Linus Torvalds [Wed, 30 Jan 2013 01:02:26 +0000 (12:02 +1100)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Intel, radeon and exynos fixes. Nothing too major or wierd: one dmar
fix and a radeon cursor corruption, along with misc exynos fixes."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (21 commits)
drm/exynos: add check for the device power status
drm/exynos: Make 'drm_hdmi_get_edid' static
drm/exynos: fimd and ipp are broken on multiplatform
drm/exynos: don't include plat/gpio-cfg.h
drm/exynos: Remove "internal" interrupt handling
drm/exynos: Add missing static specifiers in exynos_drm_rotator.c
drm/exynos: Replace mdelay with usleep_range
drm/exynos: Make ipp_handle_cmd_work static
drm/exynos: Make g2d_userptr_get_dma_addr static
drm/exynos: consider DMA_NONE flag to dmabuf import
drm/exynos: free sg object if dma_map_sg is failed
drm/exynos: added validation of edid for vidi connection
drm/exynos: let drm handle edid allocations
drm/radeon: Enable DMA_IB_SWAP_ENABLE on big endian hosts.
drm/radeon: fix a rare case of double kfree
radeon_display: Use pointer return error codes
drm/radeon: fix cursor corruption on DCE6 and newer
drm/i915: dump UTS_RELEASE into the error_state
iommu/intel: disable DMAR for g4x integrated gfx
drm/i915: GFX_MODE Flush TLB Invalidate Mode must be '1' for scanline waits
...
Linus Torvalds [Wed, 30 Jan 2013 00:59:37 +0000 (11:59 +1100)]
Merge tag 'for-linus-v3.8-rc6' of git://oss.sgi.com/xfs/xfs
Pull xfs bugfixes from Ben Myers:
"Here are fixes for returning EFSCORRUPTED on probe of a non-xfs
filesystem, the stack switch in xfs_bmapi_allocate, a crash in
_xfs_buf_find, speculative preallocation as the filesystem nears
ENOSPC, an unmount hang, a race with AIO, and a regression with
xfs_fsr:
- fix return value when filesystem probe finds no XFS magic, a
regression introduced in 9802182.
- fix stack switch in __xfs_bmapi_allocate by moving the check for
stack switch up into xfs_bmapi_write.
- fix oops in _xfs_buf_find by validating that the requested block is
within the filesystem bounds.
- limit speculative preallocation near ENOSPC.
- fix an unmount hang in xfs_wait_buftarg by freeing the
xfs_buf_log_item in xfs_buf_item_unlock.
- fix a possible use after free with AIO.
- fix xfs_swap_extents after removal of xfs_flushinval_pages, a
regression introduced in commit fb59581404a."
* tag 'for-linus-v3.8-rc6' of git://oss.sgi.com/xfs/xfs:
xfs: Fix xfs_swap_extents() after removal of xfs_flushinval_pages()
xfs: Fix possible use-after-free with AIO
xfs: fix shutdown hang on invalid inode during create
xfs: limit speculative prealloc near ENOSPC thresholds
xfs: fix _xfs_buf_find oops on blocks beyond the filesystem end
xfs: pull up stack_switch check into xfs_bmapi_write
xfs: Do not return EFSCORRUPTED when filesystem probe finds no XFS magic
Linus Torvalds [Wed, 30 Jan 2013 00:58:26 +0000 (11:58 +1100)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull one s390 fix from Martin Schwidefsky:
"Another transparent huge page fix, we need to define a s390 variant
for pmdp_set_wrprotect to flush the TLB for the huge page correctly."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/thp: implement pmdp_set_wrprotect()
Linus Torvalds [Wed, 30 Jan 2013 00:34:50 +0000 (11:34 +1100)]
Merge tag 'pinctrl-fixes-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl fixes from Linus Walleij:
"This is a late pinctrl fix pull request, we had to revert out the
pinctrl-single GPIO backend, because of, well, design issues. We're
cooking a better thing for the next cycle.
- Revert gpio request/free backend, new patch set in the works, will
be for v3.9. Get this old cruft out before anyone hurts himself on
it.
- Kconfig buzz
- Various compile warnings
- MPP6 value for the Kirkwood"
* tag 'pinctrl-fixes-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: nomadik: nmk_prcm_gpiocr_get_mode may be unused
pinctrl: exynos: don't mark probing functions as __init
Revert "pinctrl: single: support gpio request and free"
pinctrl: mvebu: fix MPP6 value for kirkwood driver
pinctrl: mvebu: Fix compiler warnings
pinctrl: pinctrl-mxs: Fix variables' definition type
pinctrl: samsung: removing duplicated condition for PINCTRL_SAMSUNG
Arnd Bergmann [Fri, 25 Jan 2013 14:14:30 +0000 (14:14 +0000)]
pinctrl: nomadik: nmk_prcm_gpiocr_get_mode may be unused
nmk_prcm_gpiocr_get_mode is only needed for debugfs output at
the moment, which can be compile-time disabled. Marking
the function __maybe_unused still gives us compile-time
coverage, but avoids a gcc warning.
Without this patch, building nhk8815_defconfig results in:
drivers/pinctrl/pinctrl-nomadik.c:676:12: warning: 'nmk_prcm_gpiocr_get_mode' defined but not used [-Wunused-function]
Arnd Bergmann [Fri, 25 Jan 2013 14:14:29 +0000 (14:14 +0000)]
pinctrl: exynos: don't mark probing functions as __init
Functions called from a driver probe() method must not be
marked __init, because they may get called after the
init phase is done, when the device shows up late, or
because of deferred probing.
Without this patch, building exynos_defconfig results in
multiple warnings like:
WARNING: drivers/pinctrl/built-in.o(.text+0x51bc): Section mismatch in reference from the function exynos5440_pinctrl_probe() to the function .init.text:exynos5440_gpiolib_register()
The function exynos5440_pinctrl_probe() references
the function __init exynos5440_gpiolib_register().
This is often because exynos5440_pinctrl_probe lacks a __init
annotation or the annotation of exynos5440_gpiolib_register is wrong.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Cc: Tomasz Figa <t.figa@samsung.com> Acked-by: Kukjin Kim <kgene.kim@samsung.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
x86, efi: remove attribute check from setup_efi_pci
It looks like the original commit that copied the rom contents from
efi always copied the rom, and the fixup in setup_efi_pci from commit 886d751a2ea99a160 ("x86, efi: correct precedence of operators in
setup_efi_pci") broke that.
This resulted in macbook pro's no longer finding the rom images, and
thus not being able to use the radeon card any more.
The solution is to just remove the check for now, and always copy the
rom if available.
Takashi Iwai [Tue, 29 Jan 2013 17:07:22 +0000 (18:07 +0100)]
ALSA: hda - Fix non-snoop page handling
For non-snoop mode, we fiddle with the page attributes of CORB/RIRB
and the position buffer, but also the ring buffers. The problem is
that the current code blindly assumes that the buffer is contiguous.
However, the ring buffers may be SG-buffers, thus a wrong vmapped
address is passed there, leading to Oops.
Currently we use LPIB forcibly for both playback and capture for
Poulsbo and Oaktrail devices, and this seems rather problematic.
The recent fix for LPIB delay count seems working well with these
devices, so let's enable it instead.
Reported-by: Martin Weishart <martin.weishart@telosalliance.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Linus Torvalds [Tue, 29 Jan 2013 06:44:53 +0000 (22:44 -0800)]
Merge tag 'regulator-3.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"Fairly small stuff - a build failure fix for ST platforms, an error
checking fix and an update to the MAINTAINERS file for Liam."
* tag 'regulator-3.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: tps80031: Use IS_ERR to check return value of regulator_register()
regulators: db8500: Fix compile failure for drivers/regulator/dbx500-prcmu.c
regulator: MAINTAINERS: update email address
Linus Torvalds [Tue, 29 Jan 2013 00:23:07 +0000 (16:23 -0800)]
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull powerpc fixes from Benjamin Herrenschmidt:
"Whenever you have a chance between two dives, you might want to
consider pulling my merge branch to pickup a few fixes for 3.8 that
have been accumulating for the last couple of weeks (I was myself
travelling then on vacation).
Nothing major, just a handful of powerpc bug fixes that I consider
worth getting in before 3.8 goes final."
And I'll have everybody know that I'm not diving for several days yet.
Snif.
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Max next_tb to prevent from replaying timer interrupt
powerpc: kernel/kgdb.c: Fix memory leakage
powerpc/book3e: Disable interrupt after preempt_schedule_irq
powerpc/oprofile: Fix error in oprofile power7_marked_instr_event() function
powerpc/pasemi: Fix crash on reboot
powerpc: Fix MAX_STACK_TRACE_ENTRIES too low warning for ppc32
Tiejun Chen [Tue, 15 Jan 2013 17:01:19 +0000 (17:01 +0000)]
powerpc: Max next_tb to prevent from replaying timer interrupt
With lazy interrupt, we always call __check_irq_replaysome with
decrementers_next_tb to check if we need to replay timer interrupt.
So in hotplug case we also need to set decrementers_next_tb as MAX
to make sure __check_irq_replay don't replay timer interrupt
when return as we expect, otherwise we'll trap here infinitely.
Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tiejun Chen [Sun, 6 Jan 2013 00:49:34 +0000 (00:49 +0000)]
powerpc/book3e: Disable interrupt after preempt_schedule_irq
In preempt case current arch_local_irq_restore() from
preempt_schedule_irq() may enable hard interrupt but we really
should disable interrupts when we return from the interrupt,
and so that we don't get interrupted after loading SRR0/1.
Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com> CC: <stable@vger.kernel.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Carl E. Love [Thu, 29 Nov 2012 06:42:03 +0000 (06:42 +0000)]
powerpc/oprofile: Fix error in oprofile power7_marked_instr_event() function
The calculation for the left shift of the mask OPROFILE_PM_PMCSEL_MSK has an
error. The calculation is should be to shift left by (max_cntrs - cntr) times
the width of the pmsel field width. However, the #define OPROFILE_MAX_PMC_NUM
was used instead of OPROFILE_PMSEL_FIELD_WIDTH. This patch fixes the
calculation.
Signed-off-by: Carl Love <cel@us.ibm.com> Acked-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Steven Rostedt [Mon, 21 Jan 2013 17:23:26 +0000 (17:23 +0000)]
powerpc/pasemi: Fix crash on reboot
commit f96972f2dc "kernel/sys.c: call disable_nonboot_cpus() in
kernel_restart()"
added a call to disable_nonboot_cpus() on kernel_restart(), which tries
to shutdown all the CPUs except the first one. The issue with the PA
Semi, is that it does not support CPU hotplug.
When the call is made to __cpu_down(), it calls the notifiers
CPU_DOWN_PREPARE, and then tries to take the CPU down.
One of the notifiers to the CPU hotplug code, is the cpufreq. The
DOWN_PREPARE will call __cpufreq_remove_dev() which calls
cpufreq_driver->exit. The PA Semi exit handler unmaps regions of I/O
that is used by an interrupt that goes off constantly
(system_reset_common, but it goes off during normal system operations
too). I'm not sure exactly what this interrupt does.
Running a simple function trace, you can see it goes off quite a bit:
Li Zhong [Sun, 2 Dec 2012 20:19:22 +0000 (20:19 +0000)]
powerpc: Fix MAX_STACK_TRACE_ENTRIES too low warning for ppc32
This patch fixes MAX_STACK_TRACE_ENTRIES too low warning for ppc32,
which is similar to commit 12660b17.
Reported-by: Christian Kujau <lists@nerdbynature.de> Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com> Tested-by: Christian Kujau <lists@nerdbynature.de> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
projects / mirror_ubuntu-eoan-kernel.git / log