Yang Li [Fri, 12 May 2023 06:46:55 +0000 (14:46 +0800)]
accel/habanalabs: Fix some kernel-doc comments
Make the description of @regs_range_array and @regs_range_array_size
to @user_regs_range_array and @user_regs_range_array_size to silence
the warnings:
drivers/accel/habanalabs/common/security.c:506: warning: Function parameter or member 'user_regs_range_array' not described in 'hl_init_pb_ranges_single_dcore'
drivers/accel/habanalabs/common/security.c:506: warning: Function parameter or member 'user_regs_range_array_size' not described in 'hl_init_pb_ranges_single_dcore'
drivers/accel/habanalabs/common/security.c:506: warning: Excess function parameter 'regs_range_array' description in 'hl_init_pb_ranges_single_dcore'
drivers/accel/habanalabs/common/security.c:506: warning: Excess function parameter 'regs_range_array_size' description in 'hl_init_pb_ranges_single_dcore'
Reported-by: Abaci Robot <abaci@linux.alibaba.com> Closes: https://bugzilla.openanolis.cn/show_bug.cgi?id=4940 Signed-off-by: Yang Li <yang.lee@linux.alibaba.com> Reviewed-by: Oded Gabbay <ogabbay@kernel.org> Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Koby Elbaz [Mon, 27 Mar 2023 08:56:16 +0000 (11:56 +0300)]
accel/habanalabs: poll for device status update following WFE cmd
Currently, we rely on COMMS protocol's ack to verify that WFE command
has been acknowledged by the FW. However, this does not guarantee that
the device status has been updated.
Although unlikely, this could trigger a race since the driver expects
the device to be halted at that stage, but it might not be.
Therefore, we increase WFE's robustness by polling on the status
register that will be updated once the device is actually halted.
Tomer Tayar [Sun, 19 Mar 2023 19:46:44 +0000 (21:46 +0200)]
accel/habanalabs: expose debugfs files later
Currently the debugfs root folder and files for a device are created at
an early step, before the device initialization and before the char
device and sysfs files are exposed to user.
As there is no real reason not to do it together with the device
creation, postpone it to be done right afterwards.
The initialization of the debugfs entry structure is left in its
current position because it is used before creating the files.
accel/habanalabs: add pci health check during heartbeat
Currently upon a heartbeat failure, we don't know if the failure
is due to firmware hang or due to a bad PCI link. Hence, we
are reading a PCI config space register with a known value (vendor ID)
so we will know which of the two possibilities caused the heartbeat
failure.
accel/habanalabs: minimize encapsulation signal mutex lock time
Sync Stream Encapsulated Signal Handlers can be managed from different
contexts, and as such they are protected via a spin_lock.
However, spin_lock was unnecessarily protecting a larger code section
than really needed, covering a sleepable code section as well.
Since spin_lock disables preemption, it could lead to sleeping in
atomic context.
Dafna Hirschfeld [Thu, 16 Mar 2023 08:20:44 +0000 (10:20 +0200)]
accel/habanalabs: extract and save the FW's SW major/minor/sub-minor
It is not always possible to know the FW's SW version from the inner FW
version. Therefore we should extract the general SW version in addition
to the FW version and use it in functions like
'hl_is_fw_ver_below_1_9' etc.
accel/habanalabs: rename fw_{major/minor}_version to fw_inner_{major/minor}_ver
We later want to add fields for Firmware SW version. The current
extracted FW version is the inner FW versioning so the new name
is better and also better differentiate from the FW's SW version.
accel/habanalabs: allow user to modify EDMA RL register
EDMA transpose workload requires to signal for every activation.
User FW sends all the dummy signals to RD_LBW_RATE_LIM_CFG, to save
lbw bandwidth. We need the user to be able to access that register to
configure it.
Tal Cohen [Thu, 30 Mar 2023 10:38:19 +0000 (13:38 +0300)]
accel/habanalabs: ignore false positive razwi
In Gaudi2 asic, PSOC RAZWI may cause in HBW or LBW. The address that
caused the error is read from HW register and printed by the Driver.
There are cases where the Driver receives an indication on PSOC
RAZWI error but the address value is zero. In that case, the indication
is a false positive.
The Driver should not "count" a PSOC RAZWI event error when the
caused the address is zeroed.
Tom Rix [Tue, 11 Apr 2023 14:08:50 +0000 (10:08 -0400)]
accel/habanalabs: remove variable gaudi_irq_name
gcc with W=1 reports
drivers/accel/habanalabs/gaudi/gaudi.c:117:19: error:
‘gaudi_irq_name’ defined but not used [-Werror=unused-const-variable=]
117 | static const char gaudi_irq_name[GAUDI_MSI_ENTRIES][GAUDI_MAX_STRING_LEN] = {
| ^~~~~~~~~~~~~~
Implement dedicated fbdev helpers for framebuffer I/O instead
of using DRM's helpers. Use an fbdev generator macro for
deferred I/O to create the fbdev callbacks. i915 was the only
caller of the DRM helpers, so remove them from the helper module.
i915's fbdev emulation is still incomplete as it doesn't implement
deferred I/O and damage handling for mmaped pages.
v4:
* generate deferred-I/O helpers
* use initializer macros for fb_ops
v2:
* use FB_IO_HELPERS options
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de> Reviewed-by: Sam Ravnborg <sam@ravnborg.org> Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com> Cc: "Ville Syrjälä" <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20230530151228.22979-14-tzimmermann@suse.de
Implement dedicated fbdev helpers for framebuffer I/O instead
of using DRM's helpers. Use an fbdev generator macro for
deferred I/O to create the callbacks. Fbdev-generic was the
only caller of the DRM helpers, so remove them from the helper
module.
v4:
* generate deferred-I/O helpers
* use initializer macros for fb_ops
v2:
* use FB_SYS_HELPERS_DEFERRED option
Use the regular fbdev helpers for framebuffer I/O instead of DRM's
helpers. Msm does not use damage handling, so DRM's fbdev helpers
are mere wrappers around the fbdev code.
By using fbdev helpers directly within each DRM fbdev emulation,
we can eventually remove DRM's wrapper functions entirely.
Msm's fbdev emulation has been incomplete as it didn't implement
damage handling. Partilly fix this by implementing damage handling
for write and draw operation. It is still missing for mmaped pages.
v4:
* use initializer macros for struct fb_ops
* partially support damage handling
v2:
* use FB_SYS_HELPERS option
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Acked-by: Sam Ravnborg <sam@ravnborg.org> Cc: Rob Clark <robdclark@gmail.com> Cc: Abhinav Kumar <quic_abhinavk@quicinc.com> Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Cc: Sean Paul <sean@poorly.run> Link: https://patchwork.freedesktop.org/patch/msgid/20230530151228.22979-12-tzimmermann@suse.de
drm/fb-helper: Export helpers for marking damage areas
Export drm_fb_helper_damage() and drm_fb_helper_damage_range(), which
handle damage areas for fbdev emulation. This is a temporary export
that allows to move the DRM I/O helpers for fbdev into drivers. Only
fbdev-generic and i915 need them. Both will be updated to implement
damage handling by themselves and the exported functions will be removed.
Use the regular fbdev helpers for framebuffer I/O instead of DRM's
helpers. Tegra does not use damage handling, so DRM's fbdev helpers
are mere wrappers around the fbdev code.
By using fbdev helpers directly within each DRM fbdev emulation,
we can eventually remove DRM's wrapper functions entirely.
v4:
* use initializer macros for struct fb_ops
v2:
* use FB_SYS_HELPERS option
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de> Acked-by: Sam Ravnborg <sam@ravnborg.org> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: Mikko Perttunen <mperttunen@nvidia.com> Cc: Jonathan Hunter <jonathanh@nvidia.com> Acked-by: Thierry Reding <treding@nvidia.com> Link: https://patchwork.freedesktop.org/patch/msgid/20230530151228.22979-10-tzimmermann@suse.de
Use the regular fbdev helpers for framebuffer I/O instead of DRM's
helpers. Omapdrm does not use damage handling, so DRM's fbdev helpers
are mere wrappers around the fbdev code.
By using fbdev helpers directly within each DRM fbdev emulation,
we can eventually remove DRM's wrapper functions entirely.
v4:
* use initializer macros for struct fb_ops
v2:
* use FB_SYS_HELPERS option
Use the regular fbdev helpers for framebuffer I/O instead of DRM's
helpers. Fbdev-dma does not use damage handling, so DRM's fbdev helpers
are mere wrappers around the fbdev code.
By using fbdev helpers directly within each DRM fbdev emulation,
we can eventually remove DRM's wrapper functions entirely.
v4:
* use initializer macros for struct fb_ops
v2:
* use FB_SYS_HELPERS option
Use the regular fbdev helpers for framebuffer I/O instead of DRM's
helpers. Radeon does not use damage handling, so DRM's fbdev helpers
are mere wrappers around the fbdev code.
By using fbdev helpers directly within each DRM fbdev emulation,
we can eventually remove DRM's wrapper functions entirely.
v4:
* use initializer macros for struct fb_ops
v2:
* use FB_IO_HELPERS option
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de> Acked-by: Alex Deucher <alexander.deucher@amd.com> Acked-by: Sam Ravnborg <sam@ravnborg.org> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: "Christian König" <christian.koenig@amd.com> Cc: "Pan, Xinhui" <Xinhui.Pan@amd.com> Link: https://patchwork.freedesktop.org/patch/msgid/20230530151228.22979-7-tzimmermann@suse.de
Use the regular fbdev helpers for framebuffer I/O instead of DRM's
helpers. Gma500 does not use damage handling, so DRM's fbdev helpers
are mere wrappers around the fbdev code.
By using fbdev helpers directly within each DRM fbdev emulation,
we can eventually remove DRM's wrapper functions entirely.
v4:
* use initializer macros for struct fb_ops
v2:
* use FB_IO_HELPERS option
Use the regular fbdev helpers for framebuffer I/O instead of DRM's
helpers. Exynos does not use damage handling, so DRM's fbdev helpers
are mere wrappers around the fbdev code.
By using fbdev helpers directly within each DRM fbdev emulation,
we can eventually remove DRM's wrapper functions entirely.
v4:
* use initializer macros for struct fb_ops
v3:
* don't reorder Makefile rules (Sam)
v2:
* use FB_IO_HELPERS option
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de> Acked-by: Sam Ravnborg <sam@ravnborg.org> Cc: Inki Dae <inki.dae@samsung.com> Cc: Seung-Woo Kim <sw0312.kim@samsung.com> Cc: Kyungmin Park <kyungmin.park@samsung.com> Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Cc: Alim Akhtar <alim.akhtar@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/20230530151228.22979-5-tzimmermann@suse.de
Use the regular fbdev helpers for framebuffer I/O instead of DRM's
helpers. Armada does not use damage handling, so DRM's fbdev helpers
are mere wrappers around the fbdev code.
By using fbdev helpers directly within each DRM fbdev emulation,
we can eventually remove DRM's wrapper functions entirely.
v4:
* use initializer macros for struct fb_ops
v2:
* use FB_IO_HELPERS option
For framebuffers in I/O and system memory, add macros that set
struct fb_ops to the respective callback functions.
For deferred I/O, add macros that generate callback functions with
damage handling. Add initializer macros that set struct fb_ops to
the generated callbacks.
These macros can remove a lot boilerplate code from fbdev drivers.
The drivers are supposed to use the macro that is required for its
framebuffer. Each macro is split into smaller helpers, so that
drivers with non-standard callbacks can pick and customize callbacks
as needed. There are individual helper macros for read/write, mmap
and drawing.
fbdev: Add Kconfig options to select different fb_ops helpers
Many fbdev drivers use the same set of fb_ops helpers. Add Kconfig
options to select them at once. This will help with making DRM's
fbdev emulation code more modular, but can also be used to simplify
fbdev's driver configs.
Fabio Estevam [Wed, 31 May 2023 22:44:07 +0000 (19:44 -0300)]
dt-bindings: samsung,mipi-dsim: Use port-base reference
Use port-base reference for port@1.
This fixes the following schema warning:
imx8mp-dhcom-pdk3.dtb: dsi@32e60000: ports:port@1:endpoint: Unevaluated properties are not allowed ('data-lanes' was unexpected)
From schema: Documentation/devicetree/bindings/display/bridge/samsung,mipi-dsim.yaml
Fixes: 1f0d40d88f7a ("dt-bindings: bridge: Convert Samsung MIPI DSIM bridge to yaml") Signed-off-by: Fabio Estevam <festevam@denx.de> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
[narmstrong: removed line break between tags] Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20230531224407.1611952-1-festevam@gmail.com
On some devices the +5V Power pin of the HDMI connector and/or the ESD
protection logic is powered on by a separate regulator. Instead of
declaring this regulator as always-on, make hdmi-connector support the
additional hdmi-pwr supply.
Follow the dp-connector example and add hdmi-pwr supply to drive the 5V
pin of the HDMI connector (together with some simple glue logic possibly
attached to the connector).
Uwe Kleine-König [Tue, 30 May 2023 07:42:16 +0000 (09:42 +0200)]
drm/panel-edp: Convert to platform remove callback returning void
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
panel_edp_remove() always returned zero, so convert it to return void
without any loss and then just drop the return from
panel_edp_platform_remove().
Uwe Kleine-König [Fri, 26 May 2023 09:07:09 +0000 (11:07 +0200)]
drm: Switch i2c drivers back to use .probe()
After commit b8a1a4cd5a98 ("i2c: Provide a temporary .probe_new()
call-back type"), all drivers being converted to .probe_new() and then 03c835f498b5 ("i2c: Switch .probe() to not take an id parameter") convert
back to (the new) .probe() to be able to eventually drop .probe_new() from
struct i2c_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com> Reviewed-by: Javier Martinez Canillas <javierm@redhat.com> Reviewed-by: Martyn Welch <martyn.welch@collabora.com> Reviewed-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Guenter Roeck <groeck@chromium.org> Signed-off-by: Douglas Anderson <dianders@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20230526090709.1517297-1-u.kleine-koenig@pengutronix.de
Adam Ford [Sun, 28 May 2023 13:27:27 +0000 (08:27 -0500)]
dt-bindings: bridge: samsung-dsim: Make some flags optional
In the event a device is connected to the samsung-dsim
controller that doesn't support the burst-clock, the
driver is able to get the requested pixel clock from the
attached device or bridge. In these instances, the
samsung,burst-clock-frequency isn't needed, so remove
it from the required list.
The pll-clock frequency can be set by the device tree entry
for samsung,pll-clock-frequency, but in some cases, the
pll-clock may have the same clock rate as sclk_mipi clock.
If they are equal, this flag is not needed since the driver
will use the sclk_mipi rate as a fallback.
Signed-off-by: Adam Ford <aford173@gmail.com> Reviewed-by: Conor Dooley <conor.dooley@microchip.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20230528132727.3933-1-aford173@gmail.com
Dave Airlie [Sun, 28 May 2023 20:21:50 +0000 (06:21 +1000)]
Merge tag 'drm-intel-gt-next-2023-05-24' of git://anongit.freedesktop.org/drm/drm-intel into drm-next
UAPI Changes:
- New getparam for querying PXP support and load status
Cross-subsystem Changes:
- GSC/MEI proxy driver
Driver Changes:
Fixes/improvements/new stuff:
- Avoid clearing pre-allocated framebuffers with the TTM backend (Nirmoy Das)
- Implement framebuffer mmap support (Nirmoy Das)
- Disable sampler indirect state in bindless heap (Lionel Landwerlin)
- Avoid out-of-bounds access when loading HuC (Lucas De Marchi)
- Actually return an error if GuC version range check fails (John Harrison)
- Get mutex and rpm ref just once in hwm_power_max_write (Ashutosh Dixit)
- Disable PL1 power limit when loading GuC firmware (Ashutosh Dixit)
- Block in hwmon while waiting for GuC reset to complete (Ashutosh Dixit)
- Provide sysfs for SLPC efficient freq (Vinay Belgaumkar)
- Add support for total context runtime for GuC back-end (Umesh Nerlige Ramappa)
- Enable fdinfo for GuC backends (Umesh Nerlige Ramappa)
- Don't capture Gen8 regs on Xe devices (John Harrison)
- Fix error capture for virtual engines (John Harrison)
- Track patch level versions on reduced version firmware files (John Harrison)
- Decode another GuC load failure case (John Harrison)
- GuC loading and firmware table handling fixes (John Harrison)
- Fix confused register capture list creation (John Harrison)
- Dump error capture to kernel log (John Harrison)
- Dump error capture to dmesg on CTB error (John Harrison)
- Disable rps_boost debugfs when SLPC is used (Vinay Belgaumkar)
Future platform enablement:
- Disable stolen memory backed FB for A0 [mtl] (Nirmoy Das)
- Various refactors for multi-tile enablement (Andi Shyti, Tejas Upadhyay)
- Extend Wa_22011802037 to MTL A-step (Madhumitha Tolakanahalli Pradeep)
- WA to clear RDOP clock gating [mtl] (Haridhar Kalvala)
- Set has_llc=0 [mtl] (Fei Yang)
- Define MOCS and PAT tables for MTL (Madhumitha Tolakanahalli Pradeep)
- Add PTE encode function [mtl] (Fei Yang)
- fix mocs selftest [mtl] (Fei Yang)
- Workaround coherency issue for Media [mtl] (Fei Yang)
- Add workaround 14018778641 [mtl] (Tejas Upadhyay)
- Implement Wa_14019141245 [mtl] (Radhakrishna Sripada)
- Fix the wa number for Wa_22016670082 [mtl] (Radhakrishna Sripada)
- Use correct huge page manager for MTL (Jonathan Cavitt)
- GSC/MEI support for Meteorlake (Alexander Usyskin, Daniele Ceraolo Spurio)
- Define GuC firmware version for MTL (John Harrison)
- Drop FLAT CCS check [mtl] (Pallavi Mishra)
- Add MTL for remapping CCS FBs [mtl] (Clint Taylor)
- Meteorlake PXP enablement (Alan Previn)
- Do not enable render power-gating on MTL (Andrzej Hajda)
- Add MTL performance tuning changes (Radhakrishna Sripada)
- Extend Wa_16014892111 to MTL A-step (Radhakrishna Sripada)
- PMU multi-tile support (Tvrtko Ursulin)
- End support for set caching ioctl [mtl] (Fei Yang)
Driver refactors:
- Use i915 instead of dev_priv insied the file_priv structure (Andi Shyti)
- Use proper parameter naming in for_each_engine() (Andi Shyti)
- Use gt_err for GT info (Tejas Upadhyay)
- Consolidate duplicated capture list code (John Harrison)
- Capture list naming clean up (John Harrison)
- Use kernel-doc -Werror when CONFIG_DRM_I915_WERROR=y (Jani Nikula)
- Preparation for using PAT index (Fei Yang)
- Use pat_index instead of cache_level (Fei Yang)
Miscellaneous:
- Fix memory leaks in i915 selftests (Cong Liu)
- Record GT error for gt failure (Tejas Upadhyay)
- Migrate platform-dependent mock hugepage selftests to live (Jonathan Cavitt)
- Update the SLPC selftest (Vinay Belgaumkar)
- Throw out set() wrapper (Jani Nikula)
- Large driver kernel doc cleanup (Jani Nikula)
- Fix probe injection CI failures after recent change (John Harrison)
- Make unexpected firmware versions an error in debug builds (John Harrison)
- Silence UBSAN uninitialized bool variable warning (Ashutosh Dixit)
- Fix memory leaks in function live_nop_switch (Cong Liu)
Merges:
- Merge drm/drm-next into drm-intel-gt-next (Joonas Lahtinen)
Liu Ying [Wed, 10 May 2023 09:24:50 +0000 (17:24 +0800)]
drm: lcdif: Add i.MX93 LCDIF compatible string
With all previous preparations done to make it possible for the
single LCDIF embedded in i.MX93 SoC to drive multiple displays
simultaneously, add i.MX93 LCDIF compatible string as the last
step of adding i.MX93 LCDIF support.
Liu Ying [Wed, 10 May 2023 09:24:49 +0000 (17:24 +0800)]
drm: lcdif: Add multiple encoders and first bridges support
The single LCDIF embedded in i.MX93 SoC may drive multiple displays
simultaneously. Look at LCDIF output port's remote port parents to
find all enabled first bridges. Add an encoder for each found bridge
and attach the bridge to the encoder. This is a preparation for
adding i.MX93 LCDIF support.
Liu Ying [Wed, 10 May 2023 09:24:48 +0000 (17:24 +0800)]
drm: lcdif: Check consistent bus format and flags across first bridges
The single LCDIF embedded in i.MX93 SoC may drive multiple displays
simultaneously. Check bus format and flags across first bridges in
->atomic_check() to ensure they are consistent. This is a preparation
for adding i.MX93 LCDIF support.
Liu Ying [Wed, 10 May 2023 09:24:47 +0000 (17:24 +0800)]
drm: lcdif: Determine bus format and flags in ->atomic_check()
Instead of determining LCDIF output bus format and bus flags in
->atomic_enable(), do that in ->atomic_check(). This is a
preparation for the upcoming patch to check consistent bus format
and bus flags across all first downstream bridges in ->atomic_check().
New lcdif_crtc_state structure is introduced to cache bus format
and bus flags states in ->atomic_check() so that they can be read
in ->atomic_enable().
Liu Ying [Wed, 10 May 2023 09:24:46 +0000 (17:24 +0800)]
drm: lcdif: Drop unnecessary NULL pointer check on lcdif->bridge
A valid bridge is already found in lcdif_attach_bridge() and set
to lcdif->bridge, so lcdif->bridge cannot be a NULL pointer. Drop
the unnecessary NULL pointer check in KMS stage.
Liu Ying [Wed, 10 May 2023 09:24:45 +0000 (17:24 +0800)]
dt-bindings: lcdif: Add i.MX93 LCDIF support
There is one LCDIF embedded in i.MX93 SoC to connect with
MIPI DSI controller through LCDIF cross line pattern(controlled
by mediamix blk-ctrl) or connect with LVDS display bridge(LDB)
directly or connect with a parallel display through parallel
display format(also controlled by mediamix blk-ctrl). i.MX93
LCDIF IP is essentially the same to i.MX8MP LCDIF IP. Add device
tree binding for i.MX93 LCDIF.
Yang Li [Fri, 21 Apr 2023 08:34:02 +0000 (16:34 +0800)]
drm/stm: dsi: Use devm_platform_ioremap_resource()
Convert platform_get_resource(),devm_ioremap_resource() to a single call
to devm_platform_ioremap_resource(), as this is exactly what this function
does.
Dario Binacchi [Tue, 16 May 2023 08:50:39 +0000 (10:50 +0200)]
drm/panel: simple: fix active size for Ampire AM-480272H3TMQW-T01H
The previous setting was related to the overall dimension and not to the
active display area.
In the "PHYSICAL SPECIFICATIONS" section, the datasheet shows the
following parameters:
----------------------------------------------------------
| Item | Specifications | unit |
----------------------------------------------------------
| Display area | 98.7 (W) x 57.5 (H) | mm |
----------------------------------------------------------
| Overall dimension | 105.5(W) x 67.2(H) x 4.96(D) | mm |
----------------------------------------------------------
Fixes: 966fea78adf2 ("drm/panel: simple: Add support for Ampire AM-480272H3TMQW-T01H") Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com> Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
[narmstrong: fixed Fixes commit id length] Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20230516085039.3797303-1-dario.binacchi@amarulasolutions.com
Adam Ford [Fri, 26 May 2023 03:05:59 +0000 (22:05 -0500)]
dt-bindings: bridge: samsung-dsim: Make some flags optional
In the event a device is connected to the samsung-dsim
controller that doesn't support the burst-clock, the
driver is able to get the requested pixel clock from the
attached device or bridge. In these instances, the
samsung,burst-clock-frequency isn't needed, so remove
it from the required list.
The pll-clock frequency can be set by the device tree entry
for samsung,pll-clock-frequency, but in some cases, the
pll-clock may have the same clock rate as sclk_mipi clock.
If they are equal, this flag is not needed since the driver
will use the sclk_mipi rate as a fallback.
Adam Ford [Fri, 26 May 2023 03:05:58 +0000 (22:05 -0500)]
drm: bridge: samsung-dsim: Support non-burst mode
The high-speed clock is hard-coded to the burst-clock
frequency specified in the device tree. However, when
using devices like certain bridge chips without burst mode
and varying resolutions and refresh rates, it may be
necessary to set the high-speed clock dynamically based
on the desired pixel clock for the connected device.
This also removes the need to set a clock speed from
the device tree for non-burst mode operation, since the
pixel clock rate is the rate requested from the attached
device like a bridge chip. This should have no impact
for people using burst-mode and setting the burst clock
rate is still required for those users. If the burst
clock is not present, change the error message to
dev_info indicating the clock use the pixel clock.
Signed-off-by: Adam Ford <aford173@gmail.com> Tested-by: Chen-Yu Tsai <wenst@chromium.org> Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de> Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de> Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com> # imx8mm-icore Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20230526030559.326566-7-aford173@gmail.com
The DPHY timings are currently hard coded. Since the input
clock can be variable, the phy timings need to be variable
too. To facilitate this, we need to cache the hs_clock
based on what is generated from the PLL.
The phy_mipi_dphy_get_default_config_for_hsclk function
configures the DPHY timings in pico-seconds, and a small macro
converts those timings into clock cycles based on the hs_clk.
Signed-off-by: Adam Ford <aford173@gmail.com> Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Tested-by: Chen-Yu Tsai <wenst@chromium.org> Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de> Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de> Tested-by: Michael Walle <michael@walle.cc> Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com> # imx8mm-icore Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20230526030559.326566-6-aford173@gmail.com
In order to support variable DPHY timings, it's necessary
to enable GENERIC_PHY_MIPI_DPHY so phy_mipi_dphy_get_default_config
can be used to determine the nominal values for a given resolution
and refresh rate.
Signed-off-by: Adam Ford <aford173@gmail.com> Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de> Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de> Tested-by: Chen-Yu Tsai <wenst@chromium.org> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20230526030559.326566-5-aford173@gmail.com
Make the pll-clock-frequency optional. If it's present, use it
to maintain backwards compatibility with existing hardware. If it
is absent, read clock rate of "sclk_mipi" to determine the rate.
Since it can be optional, change the message from an error to
dev_info.
Signed-off-by: Adam Ford <aford173@gmail.com> Tested-by: Chen-Yu Tsai <wenst@chromium.org> Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de> Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de> Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com> # imx8mm-icore Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20230526030559.326566-4-aford173@gmail.com
Adam Ford [Fri, 26 May 2023 03:05:54 +0000 (22:05 -0500)]
drm: bridge: samsung-dsim: Fix PMS Calculator on imx8m[mnp]
According to Table 13-45 of the i.MX8M Mini Reference Manual, the min
and max values for M and the frequency range for the VCO_out
calculator were incorrect. This information was contradicted in other
parts of the mini, nano and plus manuals. After reaching out to my
NXP Rep, when confronting him about discrepencies in the Nano manual,
he responded with:
"Yes it is definitely wrong, the one that is part
of the NOTE in MIPI_DPHY_M_PLLPMS register table against PMS_P,
PMS_M and PMS_S is not correct. I will report this to Doc team,
the one customer should be take into account is the Table 13-40
DPHY PLL Parameters and the Note above."
These updated values also match what is used in the NXP downstream
kernel.
To fix this, make new variables to hold the min and max values of m
and the minimum value of VCO_out, and update the PMS calculator to
use these new variables instead of using hard-coded values to keep
the backwards compatibility with other parts using this driver.
Fixes: 4d562c70c4dc ("drm: bridge: samsung-dsim: Add i.MX8M Mini/Nano support") Signed-off-by: Adam Ford <aford173@gmail.com> Reviewed-by: Lucas Stach <l.stach@pengutronix.de> Tested-by: Chen-Yu Tsai <wenst@chromium.org> Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de> Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de> Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com> # imx8mm-icore Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20230526030559.326566-3-aford173@gmail.com
Scale the blanking packet sizes to match the ratio between HS clock
and DPI interface clock. The controller seems to do internal scaling
to the number of active lanes, so we don't take those into account.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Adam Ford <aford173@gmail.com> Tested-by: Chen-Yu Tsai <wenst@chromium.org> Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de> Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com> # imx8mm-icore Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20230526030559.326566-2-aford173@gmail.com
drm/bridge: ti-sn65dsi83: Fix enable/disable flow to meet spec
The datasheet describes the following initialization flow including
minimum delay times between each step:
1. DSI data lanes need to be in LP-11 and the clock lane in HS mode
2. toggle EN signal
3. initialize registers
4. enable PLL
5. soft reset
6. enable DSI stream
7. check error status register
To meet this requirement we need to make sure the host bridge's
pre_enable() is called first by using the pre_enable_prev_first
flag.
Furthermore we need to split enable() into pre_enable() which covers
steps 2-5 from above and enable() which covers step 7 and is called
after the host bridge's enable().
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de> Fixes: ceb515ba29ba ("drm/bridge: ti-sn65dsi83: Add TI SN65DSI83 and SN65DSI84 driver") Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com> #TQMa8MxML/MBa8Mx Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20230503163313.2640898-3-frieder@fris.de
drm: bridge: samsung-dsim: Fix i.MX8M enable flow to meet spec
According to the documentation [1] the proper enable flow is:
1. Enable DSI link and keep data lanes in LP-11 (stop state)
2. Disable stop state to bring data lanes into HS mode
Currently we do this all at once within enable(), which doesn't
allow to meet the requirements of some downstream bridges.
To fix this we now enable the DSI in pre_enable() and force it
into stop state using the FORCE_STOP_STATE bit in the ESCMODE
register until enable() is called where we reset the bit.
We currently do this only for i.MX8M as Exynos uses a different
init flow where samsung_dsim_init() is called from
samsung_dsim_host_transfer().
Rob Clark [Wed, 24 May 2023 15:59:35 +0000 (08:59 -0700)]
drm: Add fdinfo memory stats
Add support to dump GEM stats to fdinfo.
v2: Fix typos, change size units to match docs, use div_u64
v3: Do it in core
v4: more kerneldoc
v5: doc fixes
v6: Actually use u64, bit more comment docs
Signed-off-by: Rob Clark <robdclark@chromium.org> Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Acked-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Acked-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20230524155956.382440-6-robdclark@gmail.com
Rob Clark [Wed, 24 May 2023 15:59:32 +0000 (08:59 -0700)]
drm: Add common fdinfo helper
Handle a bit of the boiler-plate in a single case, and make it easier to
add some core tracked stats. This also ensures consistent behavior
across drivers for standardised fields.
v2: Update drm-usage-stats.rst, 64b client-id, rename drm_show_fdinfo
v3: Rebase on drm-misc-next
drm: shmobile: Make DRM_SHMOBILE visible on Renesas SoC platforms
The LCD Controller supported by the drm-shmob driver is present
on SuperH SH-Mobile SoCs, and on Renesas ARM SH/R-Mobile SoCs.
Unfortunately its config option is not visible on either, so the user
can never enable the support.
Fix this by dropping the dependency on ARM (for SuperH), and by widening
the dependency range to ARCH_RENESAS (for ARM).
drm: shmobile: Switch to drm_crtc_init_with_planes()
The SH-Mobile DRM driver uses the legacy drm_crtc_init(), which
advertizes only the formats in safe_modeset_formats[] (XR24 and AR24) as
being supported.
Switch to drm_crtc_init_with_planes(), and advertize all supported
(A)RGB modes, so we can use RGB565 as the default mode for the console.
Azeem Shaikh [Tue, 23 May 2023 02:19:43 +0000 (02:19 +0000)]
dma-buf/sw_sync: Replace all non-returning strlcpy with strscpy
strlcpy() reads the entire source buffer first.
This read may exceed the destination size limit.
This is both inefficient and can lead to linear read
overflows if a source string is not NUL-terminated [1].
In an effort to remove strlcpy() completely [2], replace
strlcpy() here with strscpy().
No return values were used, so direct replacement is safe.
Artur Weber [Wed, 24 May 2023 08:43:24 +0000 (10:43 +0200)]
drm/panel: samsung-s6d7aa0: use pointer for drm_mode in panel desc struct
Fixes compilation issues with older GCC versions and Clang after
changes introduced in commit 6810bb390282 ("drm/panel: Add Samsung
S6D7AA0 panel controller driver"). Tested with GCC 13.1.1, GCC 6.4.0
and Clang 16.0.3.
Fixes the following errors with Clang:
drivers/gpu/drm/panel/panel-samsung-s6d7aa0.c:312:14: error: initializer element is not a compile-time constant
.drm_mode = s6d7aa0_lsl080al02_mode,
^~~~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/panel/panel-samsung-s6d7aa0.c:415:14: error: initializer element is not a compile-time constant
.drm_mode = s6d7aa0_lsl080al03_mode,
^~~~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/panel/panel-samsung-s6d7aa0.c:443:14: error: initializer element is not a compile-time constant
.drm_mode = s6d7aa0_ltl101at01_mode,
^~~~~~~~~~~~~~~~~~~~~~~
3 errors generated.
Fixes the following errors with GCC:
drivers/gpu/drm/panel/panel-samsung-s6d7aa0.c:312:14: error: initializer element is not constant
.drm_mode = s6d7aa0_lsl080al02_mode,
^~~~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/panel/panel-samsung-s6d7aa0.c:312:14: note: (near initialization for 's6d7aa0_lsl080al02_desc.drm_mode')
drivers/gpu/drm/panel/panel-samsung-s6d7aa0.c:415:14: error: initializer element is not constant
.drm_mode = s6d7aa0_lsl080al03_mode,
^~~~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/panel/panel-samsung-s6d7aa0.c:415:14: note: (near initialization for 's6d7aa0_lsl080al03_desc.drm_mode')
drivers/gpu/drm/panel/panel-samsung-s6d7aa0.c:443:14: error: initializer element is not constant
.drm_mode = s6d7aa0_ltl101at01_mode,
^~~~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/panel/panel-samsung-s6d7aa0.c:443:14: note: (near initialization for 's6d7aa0_ltl101at01_desc.drm_mode')
Azeem Shaikh [Mon, 22 May 2023 15:52:10 +0000 (15:52 +0000)]
drm/bridge: dw-hdmi: Replace all non-returning strlcpy with strscpy
strlcpy() reads the entire source buffer first.
This read may exceed the destination size limit.
This is both inefficient and can lead to linear read
overflows if a source string is not NUL-terminated [1].
In an effort to remove strlcpy() completely [2], replace
strlcpy() here with strscpy().
No return values were used, so direct replacement is safe.
During probe, the driver registers i2c dummy devices and populates the
aux bus, which registers a device for the panel. After doing that, the
driver can still defer probe if needed. This ordering of operations is
troublesome however, because the deferred probe work will retry probing
all pending devices every time a new device is registered. Therefore, if
modules need to be loaded in order to satisfy the dependencies for this
driver to complete probe, the kernel will stall, since it'll keep trying
to probe the anx7625 driver, but never succeed, given that modules would
only be loaded after the deferred probe work completes.
Two changes are required to avoid this issue:
* Move of_find_mipi_dsi_host_by_node(), which can defer probe, to before
anx7625_register_i2c_dummy_clients() and
devm_of_dp_aux_populate_ep_devices(), which register devices.
* Make use of the done_probing callback when populating the aux bus,
so that the bridge registration is only done after the panel is
probed. This is required because the panel might need to defer probe,
but the aux bus population needs the i2c dummy devices working, so
this call couldn't just be moved to an earlier point in probe.
One caveat is that if the panel is described outside the aux bus, the
probe loop issue can still happen, but we don't have a way to avoid
it in that case since there's no callback available.
With this patch applied, it's possible to boot on
mt8192-asurada-spherion with
Fixes: adca62ec370c ("drm/bridge: anx7625: Support reading edid through aux channel") Fixes: 269332997a16 ("drm/bridge: anx7625: Return -EPROBE_DEFER if the dsi host was not found") Reported-by: "kernelci.org bot" <bot@kernelci.org> Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com> Reviewed-by: Robert Foss <rfoss@kernel.org> Signed-off-by: Robert Foss <rfoss@kernel.org> Link: https://patchwork.freedesktop.org/patch/msgid/20230518193902.891121-1-nfraprado@collabora.com
Fei Yang [Fri, 19 May 2023 05:11:02 +0000 (22:11 -0700)]
drm/i915/mtl: end support for set caching ioctl
The design is to keep Buffer Object's caching policy immutable through
out its life cycle. This patch ends the support for set caching ioctl
from MTL onward. While doing that we also set BO's to be 1-way coherent
at creation time because GPU is no longer automatically snooping CPU
cache. For userspace components needing to fine tune the caching policy
for BO's, a follow up patch will extend the GEM_CREATE uAPI to allow
them specify caching mode at BO creation time.
Tvrtko Ursulin [Fri, 19 May 2023 15:49:44 +0000 (08:49 -0700)]
drm/i915/pmu: Add reference counting to the sampling timer
We do not want to have timers per tile and waste CPU cycles and energy via
multiple wake-up sources, for a relatively un-important task of PMU
sampling, so keeping a single timer works well. But we also do not want
the first GT which goes idle to turn off the timer.
Add some reference counting, via a mask of unparked GTs, to solve this.
v2: Drop the check for unparked in i915_sample (Ashutosh)
v3: Revert v2 (Tvrtko)
Marek Vasut [Sun, 14 May 2023 11:46:25 +0000 (08:46 -0300)]
drm: bridge: samsung-dsim: Implement support for clock/data polarity swap
Implement support for DSI clock and data lane DN/DP polarity swap by
means of decoding 'lane-polarities' DT property. The controller does
support DN/DP swap of clock lane and all data lanes, the controller
does not support polarity swap of individual data lane bundles, add
a check which verifies all data lanes have the same polarity.
This has been validated on an imx8mm board that actually has the MIPI DSI
clock lanes inverted.
The Samsung DSIM IP block allows the inversion of the clock and
data lanes.
Add an optional property called 'lane-polarities' that describes the
polarities of the MIPI DSI clock and data lanes.
This property is useful for properly describing the hardware when the
board designer decided to switch the polarities of the MIPI DSI
clock and/or data lanes.
projects / mirror_ubuntu-kernels.git / log