For Sitronix st1633 multi-touch controller driver the coordinates reported
for multiple fingers were wrong, as it was always taking LSB of coordinates
from the first contact data.
Signed-off-by: Dixit Parmar <dixitparmar19@gmail.com> Reviewed-by: Martin Kepplinger <martink@posteo.de> Cc: stable@vger.kernel.org Fixes: 351e0592bfea ("Input: st1232 - add support for st1633")
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=204561 Link: https://lore.kernel.org/r/1566209314-21767-1-git-send-email-dixitparmar19@gmail.com Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
rmi_process_interrupt_requests() calls handle_nested_irq() for
each interrupt status bit it finds. If the irq domain mapping for
this bit had not yet been set up, then it ends up calling
handle_nested_irq(0), which causes a NULL pointer dereference.
There's already code that masks the irq_status bits coming out of the
hardware with current_irq_mask, presumably to avoid this situation.
However current_irq_mask seems to more reflect the actual mask set
in the hardware rather than the IRQs software has set up and registered
for. For example, in rmi_driver_reset_handler(), the current_irq_mask
is initialized based on what is read from the hardware. If the reset
value of this mask enables IRQs that Linux has not set up yet, then
we end up in this situation.
There appears to be a third unused bitmask that used to serve this
purpose, fn_irq_bits. Use that bitmask instead of current_irq_mask
to avoid calling handle_nested_irq() on IRQs that have not yet been
set up.
Signed-off-by: Evan Green <evgreen@chromium.org> Reviewed-by: Andrew Duggan <aduggan@synaptics.com> Link: https://lore.kernel.org/r/20191008223657.163366-1-evgreen@chromium.org Cc: stable@vger.kernel.org Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Since commit f889beaaab1c ("Input: da9063 - report KEY_POWER instead of
KEY_SLEEP during power key-press") KEY_SLEEP isn't supported anymore. This
caused input device to not generate any events if "dlg,disable-key-power"
is set.
Fix this by unconditionally setting KEY_POWER capability, and not
declaring KEY_SLEEP.
Fixes: f889beaaab1c ("Input: da9063 - report KEY_POWER instead of KEY_SLEEP during power key-press") Signed-off-by: Marco Felsch <m.felsch@pengutronix.de> Cc: stable@vger.kernel.org Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Clearing ch->device in ch_release() is wrong because that pointer must
remain valid until ch_remove() is called. This patch fixes the following
crash the second time a ch device is opened:
We have a test case like block/001 in blktests, which will create a scsi
device by loading scsi_debug module and then try to delete the device by
sysfs interface. At the same time, it may remove the scsi_debug module.
And getting a invalid paging request BUG_ON as following:
During deleting scsi target, the scsi_debug module have been removed. Then,
sdebug_driver_template belonged to the module cannot be accessd, resulting
in scsi_proc_hostdir_rm() BUG_ON.
To fix the bug, we add scsi_device_get() in sdev_store_delete() to try to
increase refcount of module, avoiding the module been removed.
Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20191015130556.18061-1-yuyufen@huawei.com Signed-off-by: Yufen Yu <yuyufen@huawei.com> Reviewed-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
When a non-passthrough command is terminated with CHECK CONDITION, request
sense is executed by hijacking the command descriptor. Since
scsi_eh_prep_cmnd() and scsi_eh_restore_cmnd() do not save/restore the
original command resid, the value returned on failure of the original
command is lost and replaced with the value set by the execution of the
request sense command. This value may in many instances be unaligned to the
device sector size, causing sd_done() to print a warning message about the
incorrect unaligned resid before the command is retried.
Fix this problem by saving the original command residual in struct
scsi_eh_save using scsi_eh_prep_cmnd() and restoring it in
scsi_eh_restore_cmnd(). In addition, to make sure that the request sense
command is executed with a correctly initialized command structure, also
reset the residual to 0 in scsi_eh_prep_cmnd() after saving the original
command value in struct scsi_eh_save.
Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20191001074839.1994-1-damien.lemoal@wdc.com Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com> Reviewed-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
I've got a report about a UAS drive enclosure reporting back Sense: Logical
unit access not authorized if the drive it holds is password protected.
While the drive is obviously unusable in that state as a mass storage
device, it still exists as a sd device and when the system is asked to
perform a suspend of the drive, it will be sent a SYNCHRONIZE CACHE. If
that fails due to password protection, the error must be ignored.
Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20190903101840.16483-1-oneukum@suse.com Signed-off-by: Oliver Neukum <oneukum@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
On excessive bit errors for the FCP channel ingress fibre path, the channel
notifies us. Previously, we only emitted a kernel message and a trace
record. Since performance can become suboptimal with I/O timeouts due to
bit errors, we now stop using an FCP device by default on channel
notification so multipath on top can timely failover to other paths. A new
module parameter zfcp.ber_stop can be used to get zfcp old behavior.
User explanation of new kernel message:
* Description:
* The FCP channel reported that its bit error threshold has been exceeded.
* These errors might result from a problem with the physical components
* of the local fibre link into the FCP channel.
* The problem might be damage or malfunction of the cable or
* cable connection between the FCP channel and
* the adjacent fabric switch port or the point-to-point peer.
* Find details about the errors in the HBA trace for the FCP device.
* The zfcp device driver closed down the FCP device
* to limit the performance impact from possible I/O command timeouts.
* User action:
* Check for problems on the local fibre link, ensure that fibre optics are
* clean and functional, and all cables are properly plugged.
* After the repair action, you can manually recover the FCP device by
* writing "0" into its "failed" sysfs attribute.
* If recovery through sysfs is not possible, set the CHPID of the device
* offline and back online on the service element.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Cc: <stable@vger.kernel.org> #2.6.30+ Link: https://lore.kernel.org/r/20191001104949.42810-1-maier@linux.ibm.com Reviewed-by: Jens Remus <jremus@linux.ibm.com> Reviewed-by: Benjamin Block <bblock@linux.ibm.com> Signed-off-by: Steffen Maier <maier@linux.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Currently the exit return path when sme->key_idx >= NUM_WEPKEYS is via
label 'exit' and this checks if result is non-zero, however result has
not been initialized and contains garbage. Fix this by replacing the
goto with a return with the error code.
Addresses-Coverity: ("Uninitialized scalar variable") Fixes: 0ca6d8e74489 ("Staging: wlan-ng: replace switch-case statements with macro") Signed-off-by: Colin Ian King <colin.king@canonical.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20191014110201.9874-1-colin.king@canonical.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
build_restore_pagemask() will restore the value of register $1/$at when
its restore_scratch argument is non-zero, and aims to do so by filling a
branch delay slot. Commit 0b24cae4d535 ("MIPS: Add missing EHB in mtc0
-> mfc0 sequence.") added an EHB instruction (Execution Hazard Barrier)
prior to restoring $1 from a KScratch register, in order to resolve a
hazard that can result in stale values of the KScratch register being
observed. In particular, P-class CPUs from MIPS with out of order
execution pipelines such as the P5600 & P6600 are affected.
Unfortunately this EHB instruction was inserted in the branch delay slot
causing the MFC0 instruction which performs the restoration to no longer
execute along with the branch. The result is that the $1 register isn't
actually restored, ie. the TLB refill exception handler clobbers it -
which is exactly the problem the EHB is meant to avoid for the P-class
CPUs.
Similarly build_get_pgd_vmalloc() will restore the value of $1/$at when
its mode argument equals refill_scratch, and suffers from the same
problem.
Fix this by in both cases moving the EHB earlier in the emitted code.
There's no reason it needs to immediately precede the MFC0 - it simply
needs to be between the MTC0 & MFC0.
This bug only affects Cavium Octeon systems which use
build_fast_tlb_refill_handler().
binder_mmap() tries to prevent the creation of overly big binder mappings
by silently truncating the size of the VMA to 4MiB. However, this violates
the API contract of mmap(). If userspace attempts to create a large binder
VMA, and later attempts to unmap that VMA, it will call munmap() on a range
beyond the end of the VMA, which may have been allocated to another VMA in
the meantime. This can lead to userspace memory corruption.
The following sequence of calls leads to a segfault without this commit:
Fix broken read implementation, which could be used to trigger slab info
leaks.
The driver failed to check if the custom ring buffer was still empty
when waking up after having waited for more data. This would happen on
every interrupt-in completion, even if no data had been added to the
ring buffer (e.g. on disconnect events).
Due to missing sanity checks and uninitialised (kmalloced) ring-buffer
entries, this meant that huge slab info leaks could easily be triggered.
Note that the empty-buffer check after wakeup is enough to fix the info
leak on disconnect, but let's clear the buffer on allocation and add a
sanity check to read() to prevent further leaks.
A recent commit addressing a runtime PM use-count regression, introduced
a use-after-free by not making sure we held a reference to the struct
usb_interface for the lifetime of the driver data.
If disconnect() races with release() after a process has been
interrupted, release() could end up returning early and the driver would
fail to free its driver data.
Fix races between closing a port and opening or closing another port on
the same device which could lead to a failure to start or stop the
shared interrupt URB. The latter could potentially cause a
use-after-free or worse in the completion handler on driver unbind.
It seems that the right variable to use in this case is *i*, instead of
*n*, otherwise there is an undefined behavior when right shifiting by more
than 31 bits when multiplying n by 8; notice that *n* can take values
equal or greater than 4 (4, 8, 16, ...).
Also, notice that under the current conditions (bl = 3), we are skiping
the handling of bytes 3, 7, 31... So, fix this by updating this logic
and limit *bl* up to 4 instead of up to 3.
This fix is based on function udc_stuff_fifo().
Addresses-Coverity-ID: 1454834 ("Bad bit shift operation") Fixes: 24a28e428351 ("USB: gadget driver for LPC32xx") Cc: stable@vger.kernel.org Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Link: https://lore.kernel.org/r/20191014191830.GA10721@embeddedor Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Przemysław Kopa reports that since commit b516ea586d71 ("PCI: Enable
NVIDIA HDA controllers"), the discrete GPU Nvidia GeForce GT 540M on his
2011 Samsung laptop refuses to runtime suspend, resulting in a power
regression and excessive heat.
Rivera Valdez witnesses the same issue with a GeForce GT 525M (GF108M)
of the same era, as does another Arch Linux user named "R0AR" with a
more recent GeForce GTX 1050 Ti (GP107M).
The commit exposes the discrete GPU's HDA controller and all four codecs
on the controller do not set the CLKSTOP and EPSS bits in the Supported
Power States Response. They also do not set the PS-ClkStopOk bit in the
Get Power State Response. hda_codec_runtime_suspend() therefore does
not call snd_hdac_codec_link_down(), which prevents each codec and the
PCI device from runtime suspending.
The same issue is present on some AMD discrete GPUs and we addressed it
by forcing runtime PM despite the bits not being set, see commit 57cb54e53bdd ("ALSA: hda - Force to link down at runtime suspend on
ATI/AMD HDMI").
On Asus MJ401TA (with Realtek ALC256), the headset mic is connected to
pin 0x19, with default configuration value 0x411111f0 (indicating no
physical connection).
Enable this by quirking the pin. Mic jack detection was also tested and
found to be working.
This enables use of the headset mic on this product.
If disconnect() races with release() after a process has been
interrupted, release() could end up returning early and the driver would
fail to free its driver data.
We currently assume that submissions from the sqthread are successful,
and if IO polling is enabled, we use that value for knowing how many
completions to look for. But if we overflowed the CQ ring or some
requests simply got errored and already completed, they won't be
available for polling.
For the case of IO polling and SQTHREAD usage, look at the pending
poll list. If it ever hits empty then we know that we don't have
anymore pollable requests inflight. For that case, simply reset
the inflight count to zero.
Reported-by: Pavel Begunkov <asml.silence@gmail.com> Reviewed-by: Pavel Begunkov <asml.silence@gmail.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
We need to extend the rcu_read_lock() section in rxrpc_error_report()
and use rcu_dereference_sk_user_data() instead of plain access
to sk->sk_user_data to make sure all rules are respected.
The compiler wont reload sk->sk_user_data at will, and RCU rules
prevent memory beeing freed too soon.
Fixes: f0308fb07080 ("rxrpc: Fix possible NULL pointer access in ICMP handling") Fixes: 17926a79320a ("[AF_RXRPC]: Provide secure RxRPC sockets for use by userspace and kernel both") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: David Howells <dhowells@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Some drivers just call phy_ethtool_ksettings_set() to set the
links, for those phy drivers that use genphy_read_status(), if
autoneg is on, and the link is up, than execute "ethtool -s
ethx autoneg on" will cause "link partner" information disappear.
The call trace is phy_ethtool_ksettings_set()->phy_start_aneg()
->linkmode_zero(phydev->lp_advertising)->genphy_read_status(),
the link didn't change, so genphy_read_status() just return, and
phydev->lp_advertising is zero now.
This patch moves the clear operation of lp_advertising from
phy_start_aneg() to genphy_read_lpa()/genphy_c45_read_lpa(), and
if autoneg on and autoneg not complete, just clear what the
generic functions care about.
Fixes: 88d6272acaaa ("net: phy: avoid unneeded MDIO reads in genphy_read_status") Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
NET_VENDOR_BROADCOM is intended to control a kconfig menu only.
It should not have anything to do with code generation.
As such, it should not select DIMLIB for all drivers under
NET_VENDOR_BROADCOM. Instead each driver that needs DIMLIB should
select it (being the symbols SYSTEMPORT, BNXT, and BCMGENET).
Link: https://lkml.kernel.org/r/alpine.DEB.2.21.1907021810220.13058@ramsan.of.borg/ Fixes: 4f75da3666c0 ("linux/dim: Move implementation to .c files") Reported-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: Uwe Kleine-König <uwe@kleine-koenig.org> Cc: Tal Gilboa <talgi@mellanox.com> Cc: Saeed Mahameed <saeedm@mellanox.com> Cc: netdev@vger.kernel.org Cc: linux-rdma@vger.kernel.org Cc: "David S. Miller" <davem@davemloft.net> Cc: Jakub Kicinski <jakub.kicinski@netronome.com> Cc: Doug Ledford <dledford@redhat.com> Cc: Jason Gunthorpe <jgg@mellanox.com> Cc: Leon Romanovsky <leonro@mellanox.com> Cc: Or Gerlitz <ogerlitz@mellanox.com> Cc: Sagi Grimberg <sagi@grimberg.me> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
# tc qdisc add dev eth0 clsact
# tc filter add dev eth0 egress protocol ip matchall \
> action mpls push protocol mpls_uc label 0x355aa bos 1
causes corruption of all IP packets transmitted by eth0. On TC egress, we
can't rely on the value of skb->mac_len, because it's 0 and a MPLS 'push'
operation will result in an overwrite of the first 4 octets in the packet
L2 header (e.g. the Destination Address if eth0 is an Ethernet); the same
error pattern is present also in the MPLS 'pop' operation. Fix this error
in act_mpls data plane, computing 'mac_len' as the difference between the
network header and the mac header (when not at TC ingress), and use it in
MPLS 'push'/'pop' core functions.
v2: unbreak 'make htmldocs' because of missing documentation of 'mac_len'
in skb_mpls_pop(), reported by kbuild test robot
CC: Lorenzo Bianconi <lorenzo@kernel.org> Fixes: 2a2ea50870ba ("net: sched: add mpls manipulation actions to TC") Reviewed-by: Simon Horman <simon.horman@netronome.com> Acked-by: John Hurley <john.hurley@netronome.com> Signed-off-by: Davide Caratti <dcaratti@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
# tc qdisc add dev eth0 clsact
# tc filter add dev eth0 egress matchall action mpls pop
implicitly makes the kernel drop all packets transmitted by eth0, if they
don't have a MPLS header. This behavior is uncommon: other encapsulations
(like VLAN) just let the packet pass unmodified. Since the result of MPLS
'pop' operation would be the same regardless of the presence / absence of
MPLS header(s) in the original packet, we can let skb_mpls_pop() return 0
when dealing with non-MPLS packets.
For the OVS use-case, this is acceptable because __ovs_nla_copy_actions()
already ensures that MPLS 'pop' operation only occurs with packets having
an MPLS Ethernet type (and there are no other callers in current code, so
the semantic change should be ok).
v2: better documentation of use-cases for skb_mpls_pop(), thanks to Simon
Horman
Fixes: 2a2ea50870ba ("net: sched: add mpls manipulation actions to TC") Reviewed-by: Simon Horman <simon.horman@netronome.com> Acked-by: John Hurley <john.hurley@netronome.com> Signed-off-by: Davide Caratti <dcaratti@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The KSZ8795 PHY ID is in fact used by KSZ8794/KSZ8795/KSZ8765 switches.
Update the PHY ID and name to reflect that, as this family of switches
is commonly refered to as KSZ87xx
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Andrew Lunn <andrew@lunn.ch> Cc: David S. Miller <davem@davemloft.net> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: George McCollister <george.mccollister@gmail.com> Cc: Heiner Kallweit <hkallweit1@gmail.com> Cc: Sean Nyekjaer <sean.nyekjaer@prevas.dk> Cc: Tristram Ha <Tristram.Ha@microchip.com> Cc: Woojung Huh <woojung.huh@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The KSZ8051 PHY and the KSZ8794/KSZ8795/KSZ8765 switch share exactly the
same PHY ID. Since KSZ8051 is higher in the ksphy_driver[] list of PHYs
in the micrel PHY driver, it is used even with the KSZ87xx switch. This
is wrong, since the KSZ8051 configures registers of the PHY which are
not present on the simplified KSZ87xx switch PHYs and misconfigures
other registers of the KSZ87xx switch PHYs.
Fortunatelly, it is possible to tell apart the KSZ8051 PHY from the
KSZ87xx switch by checking the Basic Status register Bit 0, which is
read-only and indicates presence of the Extended Capability Registers.
The KSZ8051 PHY has those registers while the KSZ87xx switch does not.
This patch implements simple check for the presence of this bit for
both the KSZ8051 PHY and KSZ87xx switch, to let both use the correct
PHY driver instance.
Fixes: 9d162ed69f51 ("net: phy: micrel: add support for KSZ8795") Signed-off-by: Marek Vasut <marex@denx.de> Cc: Andrew Lunn <andrew@lunn.ch> Cc: David S. Miller <davem@davemloft.net> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: George McCollister <george.mccollister@gmail.com> Cc: Heiner Kallweit <hkallweit1@gmail.com> Cc: Sean Nyekjaer <sean.nyekjaer@prevas.dk> Cc: Tristram Ha <Tristram.Ha@microchip.com> Cc: Woojung Huh <woojung.huh@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
macvlan and multicast handling is now mixed up.
The explicit issue is that macvlan interface gets broken (no traffic)
after clearing MULTICAST flag on the real interface.
We now do separate logic and consider both ALLMULTI and MULTICAST
flags on the device.
Fixes: 11ba961c9161 ("net: aquantia: Fix IFF_ALLMULTI flag functionality") Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com> Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Individual descriptors on LRO TCP session should be checked
for CRC errors. It was discovered that HW recalculates
L4 checksums on LRO session and does not break it up on bad L4
csum.
Thus, driver should aggregate HW LRO L4 statuses from all individual
buffers of LRO session and drop packet if one of the buffers has bad
L4 checksum.
Fixes: f38f1ee8aeb2 ("net: aquantia: check rx csum for all packets in LRO session") Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com> Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Chip temperature is a two byte word, colocated internally with cable
length data. We do all readouts from HW memory by dwords, thus
we should clear extra high bytes, otherwise temperature output
gets weird as soon as we attach a cable to the NIC.
Fixes: 8f8940118654 ("net: aquantia: add infrastructure to readout chip temperature") Tested-by: Holger Hoffstätte <holger@applied-asynchrony.com> Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
It was caused by when sending msgs without binding a port, in the path:
inet_sendmsg() -> inet_send_prepare() -> inet_autobind() ->
.get_port/sctp_get_port(), sp->bind_hash will be set while bp->port is
not. Later when binding another port by sctp_setsockopt_bindx(), a new
bucket will be created as bp->port is not set.
sctp's autobind is supposed to call sctp_autobind() where it does all
things including setting bp->port. Since sctp_autobind() is called in
sctp_sendmsg() if the sk is not yet bound, it should have skipped the
auto bind.
THis patch is to avoid calling inet_autobind() in inet_send_prepare()
by changing sctp_prot .no_autobind with true, also remove the unused
.get_port.
Reported-by: syzbot+d44f7bbebdea49dbc84a@syzkaller.appspotmail.com Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
When a application sends many packets with the same txtime, they may
be transmitted out of order (different from the order in which they
were enqueued).
This happens because when inserting elements into the tree, when the
txtime of two packets are the same, the new packet is inserted at the
left side of the tree, causing the reordering. The only effect of this
change should be that packets with the same txtime will be transmitted
in the order they are enqueued.
The application in question (the AVTP GStreamer plugin, still in
development) is sending video traffic, in which each video frame have
a single presentation time, the problem is that when packetizing,
multiple packets end up with the same txtime.
The receiving side was rejecting packets because they were being
received out of order.
Fixes: 25db26a91364 ("net/sched: Introduce the ETF Qdisc") Reported-by: Ederson de Souza <ederson.desouza@intel.com> Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
If an ICMP packet comes in on the UDP socket backing an AF_RXRPC socket as
the UDP socket is being shut down, rxrpc_error_report() may get called to
deal with it after sk_user_data on the UDP socket has been cleared, leading
to a NULL pointer access when this local endpoint record gets accessed.
Fix this by just returning immediately if sk_user_data was NULL.
Fixes: 17926a79320a ("[AF_RXRPC]: Provide secure RxRPC sockets for use by userspace and kernel both") Reported-by: syzbot+611164843bd48cc2190c@syzkaller.appspotmail.com Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
We need a similar fix for ipv6 as Commit 0761680d5215 ("net: ipv4: fix
listify ip_rcv_finish in case of forwarding") does for ipv4.
This issue can be reprocuded by syzbot since Commit 323ebb61e32b ("net:
use listified RX for handling GRO_NORMAL skbs") on net-next. The call
trace was:
pSeries machines on POWER9 processors can run with the XICS (legacy)
interrupt mode or with the XIVE exploitation interrupt mode. These
interrupt contollers have different interfaces for interrupt
management : XICS uses hcalls and XIVE loads and stores on a page.
H_EOI being a XICS interface the enable_scrq_irq() routine can fail
when the machine runs in XIVE mode.
Fix that by calling the EOI handler of the interrupt chip.
Fixes: f23e0643cd0b ("ibmvnic: Clear pending interrupt after device reset") Signed-off-by: Cédric Le Goater <clg@kaod.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Commit 7f683b920479 ("i825xx: switch to switch to dma_alloc_attrs")
switched dma allocation over to dma_alloc_attr, but didn't convert
the SNI part to request consistent DMA memory. This broke sni_82596
since driver doesn't do dma_cache_sync for performance reasons.
Fix this by using different DMA_ATTRs for lasi_82596 and sni_82596.
Fixes: 7f683b920479 ("i825xx: switch to switch to dma_alloc_attrs") Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
phydev->dev_flags is entirely dependent on the PHY device driver which
is going to be used, setting the internal GENET PHY revision in those
bits only makes sense when drivers/net/phy/bcm7xxx.c is the PHY driver
being used.
Fixes: 487320c54143 ("net: bcmgenet: communicate integrated PHY revision to PHY driver") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Acked-by: Doug Berger <opendmb@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
tc_ctl_action() has the ability to loop forever if tcf_action_add()
returns -EAGAIN.
This special case has been done in case a module needed to be loaded,
but it turns out that tcf_add_notify() could also return -EAGAIN
if the socket sk_rcvbuf limit is hit.
We need to separate the two cases, and only loop for the module
loading case.
While we are at it, add a limit of 10 attempts since unbounded
loops are always scary.
...instead of -EINVAL. An issue was found with older kernel versions
while unplugging a NFS client with pending RPCs, and the wrong error
code here prevented it from recovering once link is back up with a
configured address.
Incidentally, this is not an issue anymore since commit 4f8943f80883
("SUNRPC: Replace direct task wakeups from softirq context"), included
in 5.2-rc7, had the effect of decoupling the forwarding of this error
by using SO_ERROR in xs_wake_error(), as pointed out by Benjamin
Coddington.
To the best of my knowledge, this isn't currently causing any further
issue, but the error code doesn't look appropriate anyway, and we
might hit this in other paths as well.
In detail, as analysed by Gonzalo Siero, once the route is deleted
because the interface is down, and can't be resolved and we return
-EINVAL here, this ends up, courtesy of inet_sk_rebuild_header(),
as the socket error seen by tcp_write_err(), called by
tcp_retransmit_timer().
In turn, tcp_write_err() indirectly calls xs_error_report(), which
wakes up the RPC pending tasks with a status of -EINVAL. This is then
seen by call_status() in the SUN RPC implementation, which aborts the
RPC call calling rpc_exit(), instead of handling this as a
potentially temporary condition, i.e. as a timeout.
Return -EINVAL only if the input parameters passed to
ip_route_output_key_hash_rcu() are actually invalid (this is the case
if the specified source address is multicast, limited broadcast or
all zeroes), but return -ENETUNREACH in all cases where, at the given
moment, the given source address doesn't allow resolving the route.
While at it, drop the initialisation of err to -ENETUNREACH, which
was added to __ip_route_output_key() back then by commit 0315e3827048 ("net: Fix behaviour of unreachable, blackhole and
prohibit routes"), but actually had no effect, as it was, and is,
overwritten by the fib_lookup() return code assignment, and anyway
ignored in all other branches, including the if (fl4->saddr) one:
I find this rather confusing, as it would look like -ENETUNREACH is
the "default" error, while that statement has no effect.
Also note that after commit fc75fc8339e7 ("ipv4: dont create routes
on down devices"), we would get -ENETUNREACH if the device is down,
but -EINVAL if the source address is specified and we can't resolve
the route, and this appears to be rather inconsistent.
Reported-by: Stefan Walter <walteste@inf.ethz.ch> Analysed-by: Benjamin Coddington <bcodding@redhat.com> Analysed-by: Gonzalo Siero <gsierohu@redhat.com> Signed-off-by: Stefano Brivio <sbrivio@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Jesse and Ido reported the following race condition:
<CPU A, t0> - Received packet A is forwarded and cached dst entry is
taken from the nexthop ('nhc->nhc_rth_input'). Calls skb_dst_set()
<t1> - Given Jesse has busy routers ("ingesting full BGP routing tables
from multiple ISPs"), route is added / deleted and rt_cache_flush() is
called
<CPU B, t2> - Received packet B tries to use the same cached dst entry
from t0, but rt_cache_valid() is no longer true and it is replaced in
rt_cache_route() by the newer one. This calls dst_dev_put() on the
original dst entry which assigns the blackhole netdev to 'dst->dev'
<CPU A, t3> - dst_input(skb) is called on packet A and it is dropped due
to 'dst->dev' being the blackhole netdev
There are 2 issues in the v4 routing code:
1. A per-netns counter is used to do the validation of the route. That
means whenever a route is changed in the netns, users of all routes in
the netns needs to redo lookup. v6 has an implementation of only
updating fn_sernum for routes that are affected.
2. When rt_cache_valid() returns false, rt_cache_route() is called to
throw away the current cache, and create a new one. This seems
unnecessary because as long as this route does not change, the route
cache does not need to be recreated.
To fully solve the above 2 issues, it probably needs quite some code
changes and requires careful testing, and does not suite for net branch.
So this patch only tries to add the deleted cached rt into the uncached
list, so user could still be able to use it to receive packets until
it's done.
Fixes: 95c47f9cf5e0 ("ipv4: call dst_dev_put() properly") Signed-off-by: Wei Wang <weiwan@google.com> Reported-by: Ido Schimmel <idosch@idosch.org> Reported-by: Jesse Hathaway <jesse@mbuki-mvuki.org> Tested-by: Jesse Hathaway <jesse@mbuki-mvuki.org> Acked-by: Martin KaFai Lau <kafai@fb.com> Cc: David Ahern <dsahern@gmail.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
In the current code, the nvme is using a fixed 4k PRP entry size,
but if the kernel use a page size which is more than 4k, we should
consider the situation that the bv_offset may be larger than the
dev->ctrl.page_size. Otherwise we may miss setting the prp2 and then
cause the command can't be executed correctly.
Fixes: dff824b2aadb ("nvme-pci: optimize mapping of small single segment requests") Cc: stable@vger.kernel.org Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Kevin Hao <haokexin@gmail.com> Signed-off-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
mount.ocfs2 failed when reading ocfs2 filesystem superblock encounters
an error. ocfs2_initialize_super() returns before allocating ocfs2_wq.
ocfs2_dismount_volume() triggers the following panic.
Oct 15 16:09:27 cnwarekv-205120 kernel: On-disk corruption discovered.Please run fsck.ocfs2 once the filesystem is unmounted.
Oct 15 16:09:27 cnwarekv-205120 kernel: (mount.ocfs2,22804,44): ocfs2_read_locked_inode:537 ERROR: status = -30
Oct 15 16:09:27 cnwarekv-205120 kernel: (mount.ocfs2,22804,44): ocfs2_init_global_system_inodes:458 ERROR: status = -30
Oct 15 16:09:27 cnwarekv-205120 kernel: (mount.ocfs2,22804,44): ocfs2_init_global_system_inodes:491 ERROR: status = -30
Oct 15 16:09:27 cnwarekv-205120 kernel: (mount.ocfs2,22804,44): ocfs2_initialize_super:2313 ERROR: status = -30
Oct 15 16:09:27 cnwarekv-205120 kernel: (mount.ocfs2,22804,44): ocfs2_fill_super:1033 ERROR: status = -30
------------[ cut here ]------------
Oops: 0002 [#1] SMP NOPTI
CPU: 1 PID: 11753 Comm: mount.ocfs2 Tainted: G E
4.14.148-200.ckv.x86_64 #1
Hardware name: Sugon H320-G30/35N16-US, BIOS 0SSDX017 12/21/2018
task: ffff967af0520000 task.stack: ffffa5f05484000
RIP: 0010:mutex_lock+0x19/0x20
Call Trace:
flush_workqueue+0x81/0x460
ocfs2_shutdown_local_alloc+0x47/0x440 [ocfs2]
ocfs2_dismount_volume+0x84/0x400 [ocfs2]
ocfs2_fill_super+0xa4/0x1270 [ocfs2]
? ocfs2_initialize_super.isa.211+0xf20/0xf20 [ocfs2]
mount_bdev+0x17f/0x1c0
mount_fs+0x3a/0x160
Link: http://lkml.kernel.org/r/1571139611-24107-1-git-send-email-yili@winhong.com Signed-off-by: Yi Li <yilikernel@gmail.com> Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Changwei Ge <gechangwei@live.cn> Cc: Gang He <ghe@suse.com> Cc: Jun Piao <piaojun@huawei.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Commit c312ef176399 "libata/ahci: Drop PCS quirk for Denverton and
beyond" got the polarity wrong on the check for which board-ids should
have the quirk applied. The board type board_ahci_pcs7 is defined at the
end of the list such that "pcs7" boards can be special cased in the
future if they need the quirk. All prior Intel board ids "<
board_ahci_pcs7" should proceed with applying the quirk.
Reported-by: Andreas Friedrich <afrie@gmx.net> Reported-by: Stephen Douthit <stephend@silicom-usa.com> Fixes: c312ef176399 ("libata/ahci: Drop PCS quirk for Denverton and beyond") Cc: <stable@vger.kernel.org> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
This was always meant to be a temporary thing, just for testing and to
see if it actually ever triggered.
The only thing that reported it was syzbot doing disk image fuzzing, and
then that warning is expected. So let's just remove it before -rc4,
because the extra sanity testing should probably go to -stable, but we
don't want the warning to do so.
In commit 9f79b78ef744 ("Convert filldir[64]() from __put_user() to
unsafe_put_user()") I made filldir() use unsafe_put_user(), which
improves code generation on x86 enormously.
But because we didn't have a "unsafe_copy_to_user()", the dirent name
copy was also done by hand with unsafe_put_user() in a loop, and it
turns out that a lot of other architectures didn't like that, because
unlike x86, they have various alignment issues.
Most non-x86 architectures trap and fix it up, and some (like xtensa)
will just fail unaligned put_user() accesses unconditionally. Which
makes that "copy using put_user() in a loop" not work for them at all.
I could make that code do explicit alignment etc, but the architectures
that don't like unaligned accesses also don't really use the fancy
"user_access_begin/end()" model, so they might just use the regular old
__copy_to_user() interface.
So this commit takes that looping implementation, turns it into the x86
version of "unsafe_copy_to_user()", and makes other architectures
implement the unsafe copy version as __copy_to_user() (the same way they
do for the other unsafe_xyz() accessor functions).
Note that it only does this for the copying _to_ user space, and we
still don't have a unsafe version of copy_from_user().
That's partly because we have no current users of it, but also partly
because the copy_from_user() case is slightly different and cannot
efficiently be implemented in terms of a unsafe_get_user() loop (because
gcc can't do asm goto with outputs).
It would be trivial to do this using "rep movsb", which would work
really nicely on newer x86 cores, but really badly on some older ones.
Al Viro is looking at cleaning up all our user copy routines to make
this all a non-issue, but for now we have this simple-but-stupid version
for x86 that works fine for the dirent name copy case because those
names are short strings and we simply don't need anything fancier.
Fixes: 9f79b78ef744 ("Convert filldir[64]() from __put_user() to unsafe_put_user()") Reported-by: Guenter Roeck <linux@roeck-us.net> Reported-and-tested-by: Tony Luck <tony.luck@intel.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
This has been discussed several times, and now filesystem people are
talking about doing it individually at the filesystem layer, so head
that off at the pass and just do it in getdents{64}().
This is partially based on a patch by Jann Horn, but checks for NUL
bytes as well, and somewhat simplified.
There's also commentary about how it might be better if invalid names
due to filesystem corruption don't cause an immediate failure, but only
an error at the end of the readdir(), so that people can still see the
filenames that are ok.
There's also been discussion about just how much POSIX strictly speaking
requires this since it's about filesystem corruption. It's really more
"protect user space from bad behavior" as pointed out by Jann. But
since Eric Biederman looked up the POSIX wording, here it is for context:
"From readdir:
The readdir() function shall return a pointer to a structure
representing the directory entry at the current position in the
directory stream specified by the argument dirp, and position the
directory stream at the next entry. It shall return a null pointer
upon reaching the end of the directory stream. The structure dirent
defined in the <dirent.h> header describes a directory entry.
From definitions:
3.129 Directory Entry (or Link)
An object that associates a filename with a file. Several directory
entries can associate names with the same file.
...
3.169 Filename
A name consisting of 1 to {NAME_MAX} bytes used to name a file. The
characters composing the name may be selected from the set of all
character values excluding the slash character and the null byte. The
filenames dot and dot-dot have special meaning. A filename is
sometimes referred to as a 'pathname component'."
Note that I didn't bother adding the checks to any legacy interfaces
that nobody uses.
Also note that if this ends up being noticeable as a performance
regression, we can fix that to do a much more optimized model that
checks for both NUL and '/' at the same time one word at a time.
We haven't really tended to optimize 'memchr()', and it only checks for
one pattern at a time anyway, and we really _should_ check for NUL too
(but see the comment about "soft errors" in the code about why it
currently only checks for '/')
See the CONFIG_DCACHE_WORD_ACCESS case of hash_name() for how the name
lookup code looks for pathname terminating characters in parallel.
Link: https://lore.kernel.org/lkml/20190118161440.220134-2-jannh@google.com/ Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Jann Horn <jannh@google.com> Cc: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
In commit 4ed28639519c ("fs, elf: drop MAP_FIXED usage from elf_map") we
changed elf to use MAP_FIXED_NOREPLACE instead of MAP_FIXED for the
executable mappings.
Then, people reported that it broke some binaries that had overlapping
segments from the same file, and commit ad55eac74f20 ("elf: enforce
MAP_FIXED on overlaying elf segments") re-instated MAP_FIXED for some
overlaying elf segment cases. But only some - despite the summary line
of that commit, it only did it when it also does a temporary brk vma for
one obvious overlapping case.
Now Russell King reports another overlapping case with old 32-bit x86
binaries, which doesn't trigger that limited case. End result: we had
better just drop MAP_FIXED_NOREPLACE entirely, and go back to MAP_FIXED.
Yes, it's a sign of old binaries generated with old tool-chains, but we
do pride ourselves on not breaking existing setups.
This still leaves MAP_FIXED_NOREPLACE in place for the load_elf_interp()
and the old load_elf_library() use-cases, because nobody has reported
breakage for those. Yet.
Note that in all the cases seen so far, the overlapping elf sections
seem to be just re-mapping of the same executable with different section
attributes. We could possibly introduce a new MAP_FIXED_NOFILECHANGE
flag or similar, which acts like NOREPLACE, but allows just remapping
the same executable file using different protection flags.
It's not clear that would make a huge difference to anything, but if
people really hate that "elf remaps over previous maps" behavior, maybe
at least a more limited form of remapping would alleviate some concerns.
Alternatively, we should take a look at our elf_map() logic to see if we
end up not mapping things properly the first time.
In the meantime, this is the minimal "don't do that then" patch while
people hopefully think about it more.
Reported-by: Russell King <linux@armlinux.org.uk> Fixes: 4ed28639519c ("fs, elf: drop MAP_FIXED usage from elf_map") Fixes: ad55eac74f20 ("elf: enforce MAP_FIXED on overlaying elf segments") Cc: Michal Hocko <mhocko@suse.com> Cc: Kees Cook <keescook@chromium.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
We really should avoid the "__{get,put}_user()" functions entirely,
because they can easily be mis-used and the original intent of being
used for simple direct user accesses no longer holds in a post-SMAP/PAN
world.
Manually optimizing away the user access range check makes no sense any
more, when the range check is generally much cheaper than the "enable
user accesses" code that the __{get,put}_user() functions still need.
So instead of __put_user(), use the unsafe_put_user() interface with
user_access_{begin,end}() that really does generate better code these
days, and which is generally a nicer interface. Under some loads, the
multiple user writes that filldir() does are actually quite noticeable.
This also makes the dirent name copy use unsafe_put_user() with a couple
of macros. We do not want to make function calls with SMAP/PAN
disabled, and the code this generates is quite good when the
architecture uses "asm goto" for unsafe_put_user() like x86 does.
Note that this doesn't bother with the legacy cases. Nobody should use
them anyway, so performance doesn't really matter there.
The namespace.pl script does not work properly if objtree is not set to
an absolute path. The do_nm function is run from within the find
function, which changes directories.
Because of this, appending objtree, $File::Find::dir, and $source, will
return a path which is not valid from the current directory.
This used to work when objtree was set to an absolute path when using
"make namespacecheck". It appears to have not worked when calling
./scripts/namespace.pl directly.
This behavior was changed in 7e1c04779efd ("kbuild: Use relative path
for $(objtree)", 2014-05-14)
Rather than fixing the Makefile to set objtree to an absolute path, just
fix namespace.pl to work when srctree and objtree are relative. Also fix
the script to use an absolute path for these by default.
Use the File::Spec module for this purpose. It's been part of perl
5 since 5.005.
The curdir() function is used to get the current directory when the
objtree and srctree aren't set in the environment.
rel2abs() is used to convert possibly relative objtree and srctree
environment variables to absolute paths.
Finally, the catfile() function is used instead of string appending
paths together, since this is more robust when joining paths together.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Acked-by: Randy Dunlap <rdunlap@infradead.org> Tested-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
When userspace writes to the MII_ADVERTISE register, we update phylib's
advertising mask and trigger a renegotiation. However, writing to the
MII_CTRL1000 register, which contains the gigabit advertisement, does
neither. This can lead to phylib's copy of the advertisement becoming
de-synced with the values in the PHY register set, which can result in
incorrect negotiation resolution.
Fixes: 5502b218e001 ("net: phy: use phy_resolve_aneg_linkmode in genphy_read_status") Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
mdio_device_reset() makes use of the atomic-pretending API flavor for
handling the PHY reset GPIO line.
I found no hint that mdio_device_reset() is called from atomic context
and indeed it uses usleep_range() since long time, so I would assume that
it is OK to sleep there.
This patch switch to gpiod_set_value_cansleep() in mdio_device_reset().
This is relevant if e.g. the PHY reset line is tied to a I2C GPIO
controller.
This has been tested on a ZynqMP board running an upstream 4.19 kernel and
then hand-ported on current kernel tree.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Convert two functions to static inline to get ride of W=1 GCC warnings
like,
mm/gup.c: In function 'gup_pte_range':
mm/gup.c:1816:16: warning: variable 'ptem' set but not used
[-Wunused-but-set-variable]
pte_t *ptep, *ptem;
^~~~
mm/mmap.c: In function 'acct_stack_growth':
mm/mmap.c:2322:16: warning: variable 'new_start' set but not used
[-Wunused-but-set-variable]
unsigned long new_start;
^~~~~~~~~
Signed-off-by: Qian Cai <cai@lca.pw> Link: https://lore.kernel.org/lkml/1570138596-11913-1-git-send-email-cai@lca.pw/ Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
This textsearch code example does not need the '\' escapes and they can
be misleading to someone reading the example. Also, gcc and sparse warn
that the "\%d" is an unknown escape sequence.
Fixes: 5968a70d7af5 ("textsearch: fix kernel-doc warnings and add kernel-api section") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: netdev@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Fix the following build error from "make TARGETS=kvm kselftest":
libkvm.a(assert.o): relocation R_X86_64_32 against `.rodata.str1.1' can not be used when making a PIE object; recompile with -fPIC
This error is seen when build is done from the main Makefile using
kselftest target. In this case KBUILD_CPPFLAGS and CC_OPTION_CFLAGS
are defined.
When build is invoked using:
"make -C tools/testing/selftests/kvm" KBUILD_CPPFLAGS and CC_OPTION_CFLAGS
aren't defined.
There is no need to pass in KBUILD_CPPFLAGS and CC_OPTION_CFLAGS for the
check to determine if --no-pie is necessary, which is the case when these
two aren't defined when "make -C tools/testing/selftests/kvm" runs.
Fix it by simplifying the no-pie-option logic. With this change, both
build variations work.
The stmmac driver will try to acquire its private mutex during suspend
via phylink_resolve() -> stmmac_mac_link_down() -> stmmac_eee_init().
However, the phylink configuration is updated with the private mutex
held already, which causes a deadlock during suspend.
Fix this by moving the phylink configuration updates out of the region
of code protected by the private mutex.
Fixes: 19e13cb27b99 ("net: stmmac: Hold rtnl lock in suspend/resume callbacks") Suggested-by: Bitan Biswas <bbiswas@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
In function mdio_sc_cfg_reg_write(), variable "reg_value" could be
uninitialized if regmap_read() fails. However, "reg_value" is used
to decide the control flow later in the if statement, which is
potentially unsafe.
Signed-off-by: Yizhuo <yzhai003@ucr.edu> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
In acp_hw_init there are some allocations that needs to be released in
case of failure:
1- adev->acp.acp_genpd should be released if any allocation attemp for
adev->acp.acp_cell, adev->acp.acp_res or i2s_pdata fails.
2- all of those allocations should be released if
mfd_add_hotplug_devices or pm_genpd_add_device fail.
3- Release is needed in case of time out values expire.
Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
This fixes an error with how the FDT blob is reserved in memblock.
An incorrect physical address calculation exposed the FDT header to
unintended corruption, which typically manifested with of_fdt_raw_init()
faulting during late boot after fdt_totalsize() returned a wrong value.
Systems with smaller physical memory sizes more frequently trigger this
issue, as the kernel is more likely to allocate from the DMA32 zone
where bbl places the DTB after the kernel image.
Commit 671f9a3e2e24 ("RISC-V: Setup initial page tables in two stages")
changed the mapping of the DTB to reside in the fixmap area.
Consequently, early_init_fdt_reserve_self() cannot be used anymore in
setup_bootmem() since it relies on __pa() to derive a physical address,
which does not work with dtb_early_va that is no longer a valid kernel
logical address.
The reserved[0x1] region shows the effect of the pointer underflow
resulting from the __pa(initial_boot_params) offset subtraction:
This is almost entirely a comment. The bug is unlikely to manifest on
existing hardware because there is a timeout on load reservations, but
manifests on QEMU because there is no timeout.
Signed-off-by: Palmer Dabbelt <palmer@sifive.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
This patch is syncing driver with actual devicetree documentation:
Documentation/devicetree/bindings/net/qca,ar71xx.txt
|Optional subnodes:
|- mdio : specifies the mdio bus, used as a container for phy nodes
| according to phy.txt in the same directory
The driver was working with fixed phy without any noticeable issues. This bug
was uncovered by introducing dsa ar9331-switch driver.
Since no one reported this bug until now, I assume no body is using it
and this patch should not brake existing system.
Fixes: d51b6ce441d3 ("net: ethernet: add ag71xx driver") Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
If WoL is enabled we can't really stop the PHY, otherwise we will not
receive the WoL packet. Fix this by telling phylink that only the MAC is
down and only stop the PHY if WoL is not enabled.
Fixes: 74371272f97f ("net: stmmac: Convert to phylink and remove phylib logic") Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
We need to always update the MAC Hash Filter so that previous entries
are invalidated.
Found out while running stmmac selftests.
Fixes: b8ef7020d6e5 ("net: stmmac: add support for hash table size 128/256 in dwmac4") Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
of_node_put needs to be called when the device node which is got
from of_get_child_by_name finished using.
irq_domain_add_linear() also calls of_node_get() to increase refcount,
so irq_domain will not be affected when it is released.
Fixes: d8652956cf37 ("net: dsa: realtek-smi: Add Realtek SMI driver") Signed-off-by: Wen Yang <wenyang@linux.alibaba.com> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Vivien Didelot <vivien.didelot@gmail.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: netdev@vger.kernel.org Cc: linux-kernel@vger.kernel.org Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
of_node_put needs to be called when the device node which is got
from of_get_child_by_name finished using.
In both cases of success and failure, we need to release 'ports',
so clean up the code using goto.
fixes: a556c76adc05 ("net: mscc: Add initial Ocelot switch support") Signed-off-by: Wen Yang <wenyang@linux.alibaba.com> Cc: Alexandre Belloni <alexandre.belloni@bootlin.com> Cc: Microchip Linux Driver Support <UNGLinuxDriver@microchip.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: netdev@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
If the interface type is P2P_DEVICE or NAN, read the file of
'/sys/kernel/debug/ieee80211/phyx/netdev:wlanx/aqm' will get a
NULL pointer dereference. As for those interface type, the
pointer sdata->vif.txq is NULL.
Unable to handle kernel NULL pointer dereference at virtual address 00000011
CPU: 1 PID: 30936 Comm: cat Not tainted 4.14.104 #1
task: ffffffc0337e4880 task.stack: ffffff800cd20000
PC is at ieee80211_if_fmt_aqm+0x34/0xa0 [mac80211]
LR is at ieee80211_if_fmt_aqm+0x34/0xa0 [mac80211]
[...]
Process cat (pid: 30936, stack limit = 0xffffff800cd20000)
[...]
[<ffffff8000b7cd00>] ieee80211_if_fmt_aqm+0x34/0xa0 [mac80211]
[<ffffff8000b7c414>] ieee80211_if_read+0x60/0xbc [mac80211]
[<ffffff8000b7ccc4>] ieee80211_if_read_aqm+0x28/0x30 [mac80211]
[<ffffff80082eff94>] full_proxy_read+0x2c/0x48
[<ffffff80081eef00>] __vfs_read+0x2c/0xd4
[<ffffff80081ef084>] vfs_read+0x8c/0x108
[<ffffff80081ef494>] SyS_read+0x40/0x7c
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org> Acked-by: Toke Høiland-Jørgensen <toke@redhat.com> Link: https://lore.kernel.org/r/1569549796-8223-1-git-send-email-miaoqing@codeaurora.org
[trim useless data from commit message] Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
If the interface is not in MESH mode, the command 'iw wlanx mpath del'
will cause kernel panic.
The root cause is null pointer access in mpp_flush_by_proxy(), as the
pointer 'sdata->u.mesh.mpp_paths' is NULL for non MESH interface.
Unable to handle kernel NULL pointer dereference at virtual address 00000068
[...]
PC is at _raw_spin_lock_bh+0x20/0x5c
LR is at mesh_path_del+0x1c/0x17c [mac80211]
[...]
Process iw (pid: 4537, stack limit = 0xd83e0238)
[...]
[<c021211c>] (_raw_spin_lock_bh) from [<bf8c7648>] (mesh_path_del+0x1c/0x17c [mac80211])
[<bf8c7648>] (mesh_path_del [mac80211]) from [<bf6cdb7c>] (extack_doit+0x20/0x68 [compat])
[<bf6cdb7c>] (extack_doit [compat]) from [<c05c309c>] (genl_rcv_msg+0x274/0x30c)
[<c05c309c>] (genl_rcv_msg) from [<c05c25d8>] (netlink_rcv_skb+0x58/0xac)
[<c05c25d8>] (netlink_rcv_skb) from [<c05c2e14>] (genl_rcv+0x20/0x34)
[<c05c2e14>] (genl_rcv) from [<c05c1f90>] (netlink_unicast+0x11c/0x204)
[<c05c1f90>] (netlink_unicast) from [<c05c2420>] (netlink_sendmsg+0x30c/0x370)
[<c05c2420>] (netlink_sendmsg) from [<c05886d0>] (sock_sendmsg+0x70/0x84)
[<c05886d0>] (sock_sendmsg) from [<c0589f4c>] (___sys_sendmsg.part.3+0x188/0x228)
[<c0589f4c>] (___sys_sendmsg.part.3) from [<c058add4>] (__sys_sendmsg+0x4c/0x70)
[<c058add4>] (__sys_sendmsg) from [<c0208c80>] (ret_fast_syscall+0x0/0x44)
Code: e2822c02e2822001e5832004f590f000 (e1902f9f)
---[ end trace bbd717600f8f884d ]---
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org> Link: https://lore.kernel.org/r/1569485810-761-1-git-send-email-miaoqing@codeaurora.org
[trim useless data from commit message] Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The loop driver assumes that if the passed in fd is opened with
O_DIRECT, the caller wants to use direct I/O on the loop device.
However, if the underlying block device has a different block size than
the loop block queue, direct I/O can't be enabled. Instead of requiring
userspace to manually change the blocksize and re-enable direct I/O,
just change the queue block sizes to match, as well as the io_min size.
Other parts of the kernel expect these nonblocking EFI callbacks to
exist and crash when running under Xen. Since the implementations of
xen_efi_set_variable() and xen_efi_query_variable_info() do not take any
locks, use them for the nonblocking callbacks too.
The QCA8K family supports up to 7 ports. So use the existing
QCA8K_NUM_PORTS define to allocate the switch structure and limit all
operations with the switch ports.
This was not an issue until commit 0394a63acfe2 ("net: dsa: enable and
disable all ports") disabled all unused ports. Since the unused ports 7-11
are outside of the correct register range on this switch some registers
were rewritten with invalid content.
Fixes: 6b93fb46480a ("net-next: dsa: add new driver for qca8xxx family") Fixes: a0c02161ecfc ("net: dsa: variable number of ports") Fixes: 0394a63acfe2 ("net: dsa: enable and disable all ports") Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
In ca8210_probe the allocated pdata needs to be assigned to
spi_device->dev.platform_data before calling ca8210_get_platform_data.
Othrwise when ca8210_get_platform_data fails pdata cannot be released.
If a device is using multiple queues, the IO scheduler may be bypassed.
This may hurt performance for some slow MQ devices, and it also breaks
zoned devices which depend on mq-deadline for respecting the write order
in one zone.
Don't bypass io scheduler if we have one setup.
This patch can double sequential write performance basically on MQ
scsi_debug when mq-deadline is applied.
Cc: Bart Van Assche <bvanassche@acm.org> Cc: Hannes Reinecke <hare@suse.com> Cc: Dave Chinner <dchinner@redhat.com> Reviewed-by: Javier González <javier@javigon.com> Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com> Signed-off-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
If the connect times out, we may have already destroyed the
queue in the timeout handler, so test if the queue is still
allocated in the connect error handler.
Kingston NVME SSD with firmware version E8FK11.T has no interrupt after
resume with actions related to suspend to idle. This patch applied
NVME_QUIRK_SIMPLE_SUSPEND quirk to fix this issue.
Fixes: d916b1be94b6 ("nvme-pci: use host managed power state for suspend") Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=204887 Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com> Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Booting with default_ps_max_latency_us >6000 makes the device fail.
Also SUBNQN is NULL and gives a warning on each boot/resume.
$ nvme id-ctrl /dev/nvme0 | grep ^subnqn
subnqn : (null)
I use this device with an Acer Nitro 5 (AN515-43-R8BF) Laptop.
To be sure is not a Laptop issue only, I tested the device on
my server board with the same results.
( with 2x,4x link on the board and 4x link on a PCI-E card ).
By default, the NVMe/RDMA driver should support max io_size of 1MiB (or
upto the maximum supported size by the HCA). Currently, one will see that
/sys/class/block/<bdev>/queue/max_hw_sectors_kb is 1020 instead of 1024.
A non power of 2 value can cause performance degradation due to
unnecessary splitting of IO requests and unoptimized allocation units.
The number of pages per MR has been fixed here, so there is no longer any
need to reduce max_sectors by 1.
The action of saving the PCI state will cause numerous PCI configuration
space reads which depending upon the vendor implementation may cause
the drive to exit the deepest NVMe state.
In these cases ASPM will typically resolve the PCIe link state and APST
may resolve the NVMe power state. However it has also been observed
that this register access after quiesced will cause PC10 failure
on some device combinations.
To resolve this, move the PCI state saving to before SetFeatures has been
called. This has been proven to resolve the issue across a 5000 sample
test on previously failing disk/system combinations.
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com> Reviewed-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Allow the do/while statement to continue if current time
is not after the proposed time 'deadline'. Intent is to
allow loop to proceed for a specific time period. Currently
the loop, as coded, will exit after first pass.
This code is currently unable to find the dts opp tables as ti-cpufreq
needs to set them up first based on speed binning.
We stopped initializing the opp tables with platform code years ago for
device tree based booting with commit 92d51856d740 ("ARM: OMAP3+: do not
register non-dt OPP tables for device tree boot"), and all of mach-omap2
is now booting using device tree.
We currently get the following errors on init:
omap2_set_init_voltage: unable to find boot up OPP for vdd_mpu
omap2_set_init_voltage: unable to set vdd_mpu
omap2_set_init_voltage: unable to find boot up OPP for vdd_core
omap2_set_init_voltage: unable to set vdd_core
omap2_set_init_voltage: unable to find boot up OPP for vdd_iva
omap2_set_init_voltage: unable to set vdd_iva
Let's just drop the unused code. Nowadays ti-cpufreq should be used to
to initialize things properly.
Cc: Adam Ford <aford173@gmail.com> Cc: André Roth <neolynx@gmail.com> Cc: "H. Nikolaus Schaller" <hns@goldelico.com> Cc: Nishanth Menon <nm@ti.com> Cc: Tero Kristo <t-kristo@ti.com> Tested-by: Adam Ford <aford173@gmail.com> #logicpd-torpedo-37xx-devkit Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
TRM "Table 13-34. SYSCONFIG Register Field Descriptions" lists both
standbymode and idlemode that should be just the sidle and midle
registers where midle is currently unconfigured for lcdc_sysc. As
the dts data has been generated based on lcdc_sysc, we now have an
empty "ti,sysc-midle" property.
And so we currently get a warning for lcdc because of a difference
with dts provided configuration compared to the legacy platform
data. This is because lcdc has SYSC_HAS_MIDLEMODE configured in
the platform data without configuring the modes.
Let's fix the issue by adding the missing midlemode to lcdc_sysc,
and configuring the "ti,sysc-midle" property based on the TRM
values.
Fixes: f711c575cfec ("ARM: dts: am335x: Add l4 interconnect hierarchy and ti-sysc data") Cc: Jyri Sarha <jsarha@ti.com> Cc: Keerthy <j-keerthy@ti.com> Cc: Robert Nelson <robertcnelson@gmail.com> Cc: Suman Anna <s-anna@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
projects / mirror_ubuntu-eoan-kernel.git / log