Alex Deucher [Thu, 3 Nov 2011 15:21:39 +0000 (11:21 -0400)]
drm/radeon/kms: set HPD polarity in hpd_init()
Polarity needs to be set accordingly to connector status (connected
or disconnected). Set it up in hpd_init() so first hotplug works
reliably no matter what is the initial set of connector. hpd_init()
also covers resume so HPD will work correctly after resume as well.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: Jerome Glisse <j.glisse@gmail.com> Cc: stable@kernel.org Signed-off-by: Dave Airlie <airlied@redhat.com>
Alex Deucher [Tue, 1 Nov 2011 18:20:30 +0000 (14:20 -0400)]
drm/radeon/kms: add MSI module parameter
Allow the user to override whether MSIs are enabled
or not on supported ASICs. MSIs are disabled by default
on IGP chips as they tend not to work. However certain
IGP chips only seem to work with MSIs enabled.
I suspect this is a chipset or bios issue, but I'm not sure
what the proper fix is. This will at least make diagnosing
and working around the problem much easier.
Thomas Hellstrom [Tue, 25 Oct 2011 21:35:53 +0000 (23:35 +0200)]
vmwgfx: Reinstate the update_layout ioctl
We need to redefine a connector as "connected" if it matches a window
in the host preferred GUI layout.
Otherwise "smart" window managers would turn on Xorg outputs that we don't
want to be on.
This reinstates the update_layout and adds the following information to
the modesetting system.
a) Connection status <-> Equivalent to real hardware connection status
b) Preferred mode <-> Equivalent to real hardware reading EDID
c) Host window position <-> Equivalent to a real hardware scanout address
dynamic register.
It should be noted that there is no assumption here about what should be
displayed and where. Only how to access the host windows.
This also bumps minor to signal availability of the new IOCTL.
Based on code originally written by Jakob Bornecrantz
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Alex Deucher [Sun, 30 Oct 2011 20:54:27 +0000 (16:54 -0400)]
drm/radeon/kms: always do extended edid probe
Rather than having a quirk list just always check the EDID header
when probing. This is the recommended behavior according to the
display team. This avoids problems with improperly terminated
i2c lines on some boards. This is also what the proprietary
driver does.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Alex Deucher [Tue, 25 Oct 2011 21:19:00 +0000 (17:19 -0400)]
drm/radeon/kms: remove useless radeon_ddc_dump()
The function didn't work with DP, eDP, or DP bridge
connectors and thus confused users as it lead them to
believe nothing was connected or the EDID was invalid
when in fact is was, just on the aux bus rather an i2c.
It should also speed up module loading as it avoids a
bunch of extra DDC probing.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Alex Deucher [Fri, 28 Oct 2011 14:30:02 +0000 (10:30 -0400)]
drm/radeon/kms: allocate vram scratch page on 6xx+
The vram scratch was originally only used on some 7xx asics
to work around a hw bug. Allocate the scratch page on all 6xx+
radeons and set the MC_VM_SYSTEM_APERTURE_DEFAULT_ADDR to point
to it. We shouldn't ever hit it since we limit the system
aperture to vram or vram and AGP, but better safe than sorry.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Ilija Hadzic [Wed, 26 Oct 2011 19:43:58 +0000 (15:43 -0400)]
drm/radeon/kms: use defined constants for crtc/hpd count instead of hard-coded value 6
radeon_driver_irq_preinstall_kms and radeon_driver_irq_uninstall_kms
hard code the loop to 6 which happens to be the current maximum
number of crtcs and hpd pins; if one day an ASIC with more crtcs
(or hpd pins) comes out, this is a trouble waiting to happen.
introduce constants for maximum CRTC count, maximum HPD pins count
and maximum HDMI blocks count (per FIXME in radeon_irq structure)
and correct the loops in radeon_driver_irq_preinstall_kms and
radeon_driver_irq_uninstall_kms
v2: take care of goofs pointed out by Alex Deucher
Signed-off-by: Ilija Hadzic <ihadzic@research.bell-labs.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Jerome Glisse [Wed, 26 Oct 2011 15:41:22 +0000 (11:41 -0400)]
drm/radeon: flush read cache for gtt with fence on r6xx and newer GPU V3
Cayman seems to be particularly sensitive to read cache returning
old data after bind/unbind to GTT. Flush read cache for GTT range
with each fences for all new hw. Should fix several rendering glitches.
Like
V2 flush whole address space
V3 also flush shader read cache
Jerome Glisse [Fri, 28 Oct 2011 21:52:34 +0000 (17:52 -0400)]
drm/radeon: set hpd polarity at init time so hotplug detect works
Polarity needs to be set accordingly to connector status (connected
or disconnected). Set it up at module init so first hotplug works
reliably no matter what is the initial set of connector.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
cc: stable@kernel.org Signed-off-by: Dave Airlie <airlied@redhat.com>
Jerome Glisse [Mon, 24 Oct 2011 22:16:34 +0000 (18:16 -0400)]
drm/radeon: avoid bouncing connector status btw disconnected & unknown
Since force handling rework of d0d0a225e6ad43314c9aa7ea081f76adc5098ad4
we could end up bouncing connector status btw disconnected and unknown.
When connector status change a call to output_poll_changed happen which
in turn ask again for detect but with force set.
So set the load detect flags whenever we report the connector as
connected or unknown this avoid bouncing btw disconnected and unknown.
Signed-off-by: Jerome Glisse <jglisse@redhat.com> Reviewed-by: Alex Deucher <alexdeucher@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Thomas Hellstrom [Sat, 22 Oct 2011 08:36:20 +0000 (10:36 +0200)]
vmwgfx: Use "Virtual" connectors and encoders rather than "LVDS".
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Reviewed-by: Jakob Bornecrantz <jakob@vmware.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Thomas Hellstrom [Sat, 22 Oct 2011 08:36:19 +0000 (10:36 +0200)]
drm: Introduce "Virtual" connectors and encoders
This will allow us to attach various properties specific to virtual
monitors in the future.
Note that we don't export an EDID property for "Virtual" connectors.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Reviewed-by: Jakob Bornecrantz <jakob@vmware.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Linus Torvalds [Tue, 1 Nov 2011 00:46:07 +0000 (17:46 -0700)]
Merge branch 'akpm' (Andrew's incoming)
Quoth Andrew:
- Most of MM. Still waiting for the poweroc guys to get off their
butts and review some threaded hugepages patches.
- alpha
- vfs bits
- drivers/misc
- a few core kerenl tweaks
- printk() features
- MAINTAINERS updates
- backlight merge
- leds merge
- various lib/ updates
- checkpatch updates
* akpm: (127 commits)
epoll: fix spurious lockdep warnings
checkpatch: add a --strict check for utf-8 in commit logs
kernel.h/checkpatch: mark strict_strto<foo> and simple_strto<foo> as obsolete
llist-return-whether-list-is-empty-before-adding-in-llist_add-fix
wireless: at76c50x: follow rename pack_hex_byte to hex_byte_pack
fat: follow rename pack_hex_byte() to hex_byte_pack()
security: follow rename pack_hex_byte() to hex_byte_pack()
kgdb: follow rename pack_hex_byte() to hex_byte_pack()
lib: rename pack_hex_byte() to hex_byte_pack()
lib/string.c: fix strim() semantics for strings that have only blanks
lib/idr.c: fix comment for ida_get_new_above()
lib/percpu_counter.c: enclose hotplug only variables in hotplug ifdef
lib/bitmap.c: quiet sparse noise about address space
lib/spinlock_debug.c: print owner on spinlock lockup
lib/kstrtox: common code between kstrto*() and simple_strto*() functions
drivers/leds/leds-lp5521.c: check if reset is successful
leds: turn the blink_timer off before starting to blink
leds: save the delay values after a successful call to blink_set()
drivers/leds/leds-gpio.c: use gpio_get_value_cansleep() when initializing
drivers/leds/leds-lm3530.c: add __devexit_p where needed
...
Nelson Elhage [Tue, 1 Nov 2011 00:13:14 +0000 (17:13 -0700)]
epoll: fix spurious lockdep warnings
epoll can acquire recursively acquire ep->mtx on multiple "struct
eventpoll"s at once in the case where one epoll fd is monitoring another
epoll fd. This is perfectly OK, since we're careful about the lock
ordering, but it causes spurious lockdep warnings. Annotate the recursion
using mutex_lock_nested, and add a comment explaining the nesting rules
for good measure.
Recent versions of systemd are triggering this, and it can also be
demonstrated with the following trivial test program:
--------------------8<--------------------
int main(void) {
int e1, e2;
struct epoll_event evt = {
.events = EPOLLIN
};
Joe Perches [Tue, 1 Nov 2011 00:13:12 +0000 (17:13 -0700)]
checkpatch: add a --strict check for utf-8 in commit logs
Some find using utf-8 in commit logs inappropriate.
Some patch commit logs contain unintended utf-8 characters when doing
things like copy/pasting compilation output.
Look for the start of any commit log by skipping initial lines that look
like email headers and "From: " lines.
Stop looking for utf-8 at the first signature line.
Signed-off-by: Joe Perches <joe@perches.com> Suggested-by: Andrew Morton <akpm@linux-foundation.org> Cc: Andy Whitcroft <apw@shadowen.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andy Shevchenko [Tue, 1 Nov 2011 00:13:00 +0000 (17:13 -0700)]
wireless: at76c50x: follow rename pack_hex_byte to hex_byte_pack
There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michael Holzheu [Tue, 1 Nov 2011 00:12:37 +0000 (17:12 -0700)]
lib/string.c: fix strim() semantics for strings that have only blanks
Commit 84c95c9acf0 ("string: on strstrip(), first remove leading spaces
before running over str") improved\7f the performance of the strim()
function.
Unfortunately this changed the semantics of strim() and broke my code.
Before the patch it was possible to use strim() without using the return
value for removing trailing spaces from strings that had either only
blanks or only trailing blanks.
Now this does not work any longer for strings that *only* have blanks.
Before patch: " " -> "" (empty string)
After patch: " " -> " " (no change)
I think we should remove your patch to restore the old behavior.
The description (lib/string.c):
* Note that the first trailing whitespace is replaced with a %NUL-terminator
=> The first trailing whitespace of a string that only has whitespace
characters is the first whitespace
The patch restores the old strim() semantics.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com> Cc: Andre Goddard Rosa <andre.goddard@gmail.com> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Glauber Costa [Tue, 1 Nov 2011 00:12:34 +0000 (17:12 -0700)]
lib/percpu_counter.c: enclose hotplug only variables in hotplug ifdef
These variables are only used when CONFIG_HOTPLUG_CPU is enabled, they are
ifdef'ed everywhere else. So don't define them when CONFIG_HOTPLUG_CPU is
not enabled.
Signed-off-by: Glauber Costa <glommer@parallels.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
lib/bitmap.c: quiet sparse noise about address space
__bitmap_parse() and __bitmap_parselist() both take a pointer to a kernel
buffer as a parameter and then cast it to a pointer to user buffer for use
in cases when the parameter is_user indicates that the buffer is actually
located in user space. This casting, and the casts in the callers,
results in sparse noise like the following:
warning: incorrect type in initializer (different address spaces)
expected char const [noderef] <asn:1>*ubuf
got char const *buf
warning: cast removes address space of expression
Since these casts are intentional, use __force to quiet the noise.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Cc: Len Brown <len.brown@intel.com> Cc: Huang Ying <ying.huang@intel.com> Cc: Andy Shevchenko <andy.shevchenko@gmail.com> Cc: Andi Kleen <ak@linux.intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Akinobu Mita [Tue, 1 Nov 2011 00:12:29 +0000 (17:12 -0700)]
lib/spinlock_debug.c: print owner on spinlock lockup
When SPIN_BUG_ON is triggered, the lock owner information is reported.
But it is omitted when spinlock lockup is detected.
This information is useful especially on the architectures which don't
implement trigger_all_cpu_backtrace() that is called just after detecting
lockup. So report it and also avoid message format duplication.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Cc: Ingo Molnar <mingo@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alexey Dobriyan [Tue, 1 Nov 2011 00:12:28 +0000 (17:12 -0700)]
lib/kstrtox: common code between kstrto*() and simple_strto*() functions
Currently termination logic (\0 or \n\0) is hardcoded in _kstrtoull(),
avoid that for code reuse between kstrto*() and simple_strtoull().
Essentially, make them different only in termination logic.
simple_strtoull() (and scanf(), BTW) ignores integer overflow, that's a
bug we currently don't have guts to fix, making KSTRTOX_OVERFLOW hack
necessary.
Almost forgot: patch shrinks code size by about ~80 bytes on x86_64.
drivers/leds/leds-lp5521.c: check if reset is successful
Make sure that the reset is successful by issuing a dummy read to R
channel current register and check its default value. On some platforms,
without this dummy read, any further access to {R/G/B}_EXEC will not have
any impact.
[akpm@linux-foundation.org: fix up code comment] Signed-off-by: srinidhi kasagar <srinidhi.kasagar@stericsson.com> Tested-by: Naga Radhesh <naga.radheshy@stericsson.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Cc: Richard Purdie <richard.purdie@linuxfoundation.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Antonio Ospite [Tue, 1 Nov 2011 00:12:22 +0000 (17:12 -0700)]
leds: turn the blink_timer off before starting to blink
Depending on the implementation of the hardware blinking function in
blink_set(), the led can support hardware blinking for some values of
delay_on and delay_off and fall-back to software blinking for some other
values.
Turning off the blink_timer unconditionally before starting to blink
make sure that a sequence like:
OFF
hardware blinking
software blinking
hardware blinking
does not leave the software blinking timer active.
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it> Reviewed-by: Johannes Berg <johannes@sipsolutions.net> Cc: Richard Purdie <rpurdie@rpsys.net> Cc: <stable@kernel.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
My GPIOs are on an I2C port expander, so we must use the *_cansleep()
variant of the GPIO functions. This is was not being done in
create_gpio_led().
We can change gpio_get_value() to gpio_get_value_cansleep() because it is
only called from the platform_driver probe function, which is a context
where we can sleep.
Only tested on my gpio_cansleep() system, but it seems safe for all
systems.
Signed-off-by: David Daney <david.daney@cavium.com> Cc: Richard Purdie <rpurdie@rpsys.net> Acked-by: Trent Piepho <tpiepho@gmail.com> Cc: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Axel Lin [Tue, 1 Nov 2011 00:12:15 +0000 (17:12 -0700)]
drivers/leds/leds-lm3530.c: add __devexit_p where needed
According to the comments in include/linux/init.h:
"Pointers to __devexit functions must use __devexit_p(function_name), the
wrapper will insert either the function_name or NULL, depending on the config
options."
We have __devexit annotation for lm3530_remove(), so add __devexit_p to
the `struct i2c_driver'.
Signed-off-by: Axel Lin <axel.lin@gmail.com> Cc: Shreshtha Kumar SAHU <shreshthakumar.sahu@stericsson.com> Cc: Richard Purdie <rpurdie@rpsys.net> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Axel Lin [Tue, 1 Nov 2011 00:12:12 +0000 (17:12 -0700)]
drivers/leds/leds-lp5521.c: avoid writing uninitialized value to LP5521_REG_OP_MODE register
If lp5521_read fails, engine_state variable is not initialized.
If lp5521_read fails, we should return error.
This patch fixes below warning.
CC drivers/leds/leds-lp5521.o
drivers/leds/leds-lp5521.c: In function 'lp5521_set_engine_mode':
drivers/leds/leds-lp5521.c:168: warning: 'engine_state' may be used uninitialized in this function
[akpm@linux-foundation.org: remove unneeded "ret |="] Signed-off-by: Axel Lin <axel.lin@gmail.com> Cc: Samu Onkalo <samu.p.onkalo@nokia.com> Cc: Richard Purdie <rpurdie@rpsys.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Magnus Damm [Tue, 1 Nov 2011 00:12:09 +0000 (17:12 -0700)]
drivers/leds/leds-renesas-tpu.c: move Renesas TPU LED driver platform data
Use the platform_data include directory for the TPU LED driver, as
suggested by Paul Mundt.
Signed-off-by: Magnus Damm <damm@opensource.se> Cc: Paul Mundt <lethal@linux-sh.org> Cc: Richard Purdie <rpurdie@rpsys.net> Cc: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Magnus Damm [Tue, 1 Nov 2011 00:12:06 +0000 (17:12 -0700)]
drivers/leds/leds-renesas-tpu.c: update driver to use workqueue
Use a workqueue in the Renesas TPU LED driver to allow the Runtime PM code
to sleep.
Signed-off-by: Magnus Damm <damm@opensource.se> Cc: Paul Mundt <lethal@linux-sh.org> Cc: Richard Purdie <rpurdie@rpsys.net> Cc: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Wolfram Sang [Tue, 1 Nov 2011 00:12:03 +0000 (17:12 -0700)]
drivers/leds/leds-lm3530.c: remove obsolete cleanup for clientdata
A few new i2c-drivers came into the kernel which clear the
clientdata-pointer on exit or error. This is obsolete meanwhile, the core
will do it.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Cc: Richard Purdie <rpurdie@rpsys.net> Acked-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Magnus Damm [Tue, 1 Nov 2011 00:11:55 +0000 (17:11 -0700)]
leds: Renesas TPU LED driver
Add V2 of the LED driver for a single timer channel for the TPU hardware
block commonly found in Renesas SoCs.
The driver has been written with optimal Power Management in mind, so to
save power the LED is driven as a regular GPIO pin in case of maximum
brightness and power off which allows the TPU hardware to be idle and
which in turn allows the clocks to be stopped and the power domain to be
turned off transparently.
Any other brightness level requires use of the TPU hardware in PWM mode.
TPU hardware device clocks and power are managed through Runtime PM.
System suspend and resume is known to be working - during suspend the LED
is set to off by the generic LED code.
The TPU hardware timer is equipeed with a 16-bit counter together with an
up-to-divide-by-64 prescaler which makes the hardware suitable for
brightness control. Hardware blink is unsupported.
The LED PWM waveform has been verified with a Fluke 123 Scope meter on a
sh7372 Mackerel board. Tested with experimental sh7372 A3SP power domain
patches. Platform device bind/unbind tested ok.
V2 has been tested on the DS2 LED of the sh73a0-based AG5EVM.
[axel.lin@gmail.com: include linux/module.h] Signed-off-by: Magnus Damm <damm@opensource.se> Cc: Paul Mundt <lethal@linux-sh.org> Cc: Richard Purdie <rpurdie@rpsys.net> Cc: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Axel Lin [Tue, 1 Nov 2011 00:11:52 +0000 (17:11 -0700)]
backlight: rename corgibl_limit_intensity() to genericbl_limit_intensity()
The rename of corgibl_limit_intensity is missed in commit d00ba726
("backlight: Rename the corgi backlight driver to generic"). Let's fix it
now.
Signed-off-by: Axel Lin <axel.lin@gmail.com> Cc: Richard Purdie <rpurdie@rpsys.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mark Brown [Tue, 1 Nov 2011 00:11:48 +0000 (17:11 -0700)]
backlight: fix broken regulator API usage in l4f00242t03
The regulator support in the l4f00242t03 is very non-idiomatic. Rather
than requesting the regulators based on the device name and the supply
names used by the device the driver requires boards to pass system
specific supply names around through platform data. The driver also
conditionally requests the regulators based on this platform data, adding
unneeded conditional code to the driver.
Fix this by removing the platform data and converting to the standard
idiom, also updating all in tree users of the driver. As no datasheet
appears to be available for the LCD I'm guessing the names for the
supplies based on the existing users and I've no ability to do anything
more than compile test.
The use of regulator_set_voltage() in the driver is also problematic,
since fixed voltages are required the expectation would be that the
voltages would be fixed in the constraints set by the machines rather than
manually configured by the driver, but is less problematic.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Tested-by: Fabio Estevam <fabio.estevam@freescale.com> Cc: Richard Purdie <rpurdie@rpsys.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Wolfram Sang [Tue, 1 Nov 2011 00:11:44 +0000 (17:11 -0700)]
video/backlight: remove obsolete cleanup for clientdata
A few new i2c-drivers came into the kernel which clear the
clientdata-pointer on exit or error. This is obsolete meanwhile, the core
will do it.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Cc: Richard Purdie <rpurdie@rpsys.net> Cc: Paul Mundt <lethal@linux-sh.org> Acked-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jiri Kosina [Tue, 1 Nov 2011 00:11:41 +0000 (17:11 -0700)]
MAINTAINERS: add ASLR maintainer
Since achieving the full ASLR by merging the PIE randomization in commit cc503c1b43 ("x86: PIE executable randomization"), I have been dealing with
most (if not all) of the bugreports reported against userspace address
space randomization, so it might be a good idea to provide a decent
contact point in MAINTAINERS.
Signed-off-by: Jiri Kosina <jkosina@suse.cz> Cc: Josh Boyer <jwboyer@redhat.com> Cc: Nicolas Pitre <nicolas.pitre@linaro.org> Cc: Ingo Molnar <mingo@elte.hu> Cc: Russell King <rmk@arm.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
William Douglas [Tue, 1 Nov 2011 00:11:31 +0000 (17:11 -0700)]
printk: remove bounds checking for log_prefix
Currently log_prefix is testing that the first character of the log level
and facility is less than '0' and greater than '9' (which is always
false).
Since the code being updated works because strtoul bombs out (endp isn't
updated) and 0 is returned anyway just remove the check and don't change
the behavior of the function.
Signed-off-by: William Douglas <william.douglas@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
William Douglas [Tue, 1 Nov 2011 00:11:29 +0000 (17:11 -0700)]
printk: fix bounds checking for log_prefix
Currently log_prefix is testing that the first character of the log level
and facility is less than '0' and greater than '9' (which is always
false). It should be testing to see if the character less than '0' or
greater than '9' instead. This patch makes that change.
The code being changed worked because strtoul bombs out (endp isn't
updated) and 0 is returned anyway.
Signed-off-by: William Douglas <william.douglas@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dan Ballard [Tue, 1 Nov 2011 00:11:20 +0000 (17:11 -0700)]
kernel/sysctl.c: add cap_last_cap to /proc/sys/kernel
Userspace needs to know the highest valid capability of the running
kernel, which right now cannot reliably be retrieved from the header files
only. The fact that this value cannot be determined properly right now
creates various problems for libraries compiled on newer header files
which are run on older kernels. They assume capabilities are available
which actually aren't. libcap-ng is one example. And we ran into the
same problem with systemd too.
Now the capability is exported in /proc/sys/kernel/cap_last_cap.
[akpm@linux-foundation.org: make cap_last_cap const, per Ulrich] Signed-off-by: Dan Ballard <dan@mindstab.net> Cc: Randy Dunlap <rdunlap@xenotime.net> Cc: Ingo Molnar <mingo@elte.hu> Cc: Lennart Poettering <lennart@poettering.net> Cc: Kay Sievers <kay.sievers@vrfy.org> Cc: Ulrich Drepper <drepper@akkadia.org> Cc: James Morris <jmorris@namei.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Vasily Averin [Tue, 1 Nov 2011 00:11:18 +0000 (17:11 -0700)]
watchdog: move watchdog_*_all_cpus under CONFIG_SYSCTL
Fix compilation warnings for CONFIG_SYSCTL=n:
fixed compilation warnings in case of disabled CONFIG_SYSCTL
kernel/watchdog.c:483:13: warning: `watchdog_enable_all_cpus' defined but not used
kernel/watchdog.c:500:13: warning: `watchdog_disable_all_cpus' defined but not used
these functions are static and are used only in sysctl handler, so move
them inside #ifdef CONFIG_SYSCTL too
stop_machine: make stop_machine safe and efficient to call early
Make stop_machine() safe to call early in boot, before SMP has been set
up, by simply calling the callback function directly if there's only one
CPU online.
[ Fixes from AKPM:
- add comment
- local_irq_flags, not save_flags
- also call hard_irq_disable() for systems which need it
Tejun suggested using an explicit flag rather than just looking at
the online cpu count. ]
Cc: Tejun Heo <tj@kernel.org> Acked-by: Rusty Russell <rusty@rustcorp.com.au> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: H. Peter Anvin <hpa@linux.intel.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: Steven Rostedt <rostedt@goodmis.org> Acked-by: Tejun Heo <htejun@gmail.com> Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Peter Korsgaard [Tue, 1 Nov 2011 00:11:12 +0000 (17:11 -0700)]
drivers/misc/ad525x_dpot-i2c.c: add i2c support for AD5161
Commit 6c536e4ce8e ("ad525x_dpot: add support for SPI parts") added
support for the AD5161 through SPI, but the device supports both I2C and
SPI (depending on the DIS pin), so add it to -i2c as well.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk> Acked-by: Mike Frysinger <vapier@gentoo.org> Acked-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mark Brown [Tue, 1 Nov 2011 00:11:07 +0000 (17:11 -0700)]
lis3lv02d: make regulator API usage unconditional
The regulator API contains a range of features for stubbing itself out
when not in use and for transparently restricting the actual effect of
regulator API calls where they can't be supported on a particular system
so that drivers don't need to individually implement this. Simplify the
driver slightly by making use of this idiom.
The only in tree user is ecovec24 which does not use the regulator API.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: Éric Piel <eric.piel@tremplin-utc.net> Cc: Ilkka Koskinen <ilkka.koskinen@nokia.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
>From my POV, it looks like the hardware is not working as expected
and returns a bogus data rate. The driver doesn't check the result
and directly uses it as some sort of divisor in some places:
msleep(lis3->pwron_delay / lis3lv02d_get_odr());
Under this circumstances, this could very well cause the
"divide by zero" exception from above.
For now, I fixed it the easiest and most obvious way:
Check if the result is sane and if it isn't use a sane default
instead. I went for "100" in the latter case, simply because
/sys/devices/platform/lis3lv02d/rate returns it on a successful
boot.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: Éric Piel <eric.piel@tremplin-utc.net> Cc: Matthew Garrett <mjg@redhat.com> Cc: Witold Pilat <witold.pilat@gmail.com> Cc: Lyall Pearce <lyall.pearce@hp.com> Cc: Malte Starostik <m-starostik@versanet.de> Cc: Ilkka Koskinen <ilkka.koskinen@nokia.com> Cc: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com> Cc: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pavel Emelyanov [Tue, 1 Nov 2011 00:10:04 +0000 (17:10 -0700)]
fs/pipe.c: add ->statfs callback for pipefs
Currently a statfs on a pipe's /proc/<pid>/fd/ link returns -ENOSYS. Wire
pipfs up so that the statfs succeeds.
This is required by checkpoint-restart in the userspace to make it
possible to distinguish pipes from fifos.
When we dump information about task's open files we use the /proc/pid/fd
directoy's symlinks and the fact that opening any of them gives us exactly
the same dentry->inode pair as the original process has. Now if a task
we're dumping has opened pipe and fifo we need to detect this and act
accordingly. Knowing that an fd with type S_ISFIFO resides on a pipefs is
the most precise way.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com> Reviewed-by: Tejun Heo <tj@kernel.org> Acked-by: Serge Hallyn <serge.hallyn@canonical.com> Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org> Cc: Al Viro <viro@ZenIV.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michael Cree [Tue, 1 Nov 2011 00:10:01 +0000 (17:10 -0700)]
alpha: wire up sendmmsg syscall
Signed-off-by: Michael Cree <mcree@orcon.net.nz> Reviewed-by: Matt Turner <mattst88@gmail.com> Cc: Richard Henderson <rth@twiddle.net> Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michael Cree [Tue, 1 Nov 2011 00:09:49 +0000 (17:09 -0700)]
alpha: wire up accept4 syscall
Somehow wiring up the accept4 syscall on Alpha was missed long ago.
This commit rectifies that oversight.
Signed-off-by: Michael Cree <mcree@orcon.net.nz> Reviewed-by: Matt Turner <mattst88@gmail.com> Cc: Richard Henderson <rth@twiddle.net> Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hugh Dickins [Tue, 1 Nov 2011 00:09:43 +0000 (17:09 -0700)]
mm: munlock use mapcount to avoid terrible overhead
A process spent 30 minutes exiting, just munlocking the pages of a large
anonymous area that had been alternately mprotected into page-sized vmas:
for every single page there's an anon_vma walk through all the other
little vmas to find the right one.
A general fix to that would be a lot more complicated (use prio_tree on
anon_vma?), but there's one very simple thing we can do to speed up the
common case: if a page to be munlocked is mapped only once, then it is our
vma that it is mapped into, and there's no need whatever to walk through
all the others.
Okay, there is a very remote race in munlock_vma_pages_range(), if between
its follow_page() and lock_page(), another process were to munlock the
same page, then page reclaim remove it from our vma, then another process
mlock it again. We would find it with page_mapcount 1, yet it's still
mlocked in another process. But never mind, that's much less likely than
the down_read_trylock() failure which munlocking already tolerates (in
try_to_unmap_one()): in due course page reclaim will discover and move the
page to unevictable instead.
[akpm@linux-foundation.org: add comment] Signed-off-by: Hugh Dickins <hughd@google.com> Cc: Michel Lespinasse <walken@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hillf Danton [Tue, 1 Nov 2011 00:09:40 +0000 (17:09 -0700)]
mm/huge_memory: fix typo when updating mmu cache
There are three cases of update_mmu_cache() in the file, and the case in
function collapse_huge_page() has a typo, namely the last parameter used,
which is corrected based on the other two cases.
Due to the define of update_mmu_cache by X86, the only arch that
implements THP currently, the change here has no really crystal point, but
one or two minutes of efforts could be saved for those archs that are
likely to support THP in future.
Signed-off-by: Hillf Danton <dhillf@gmail.com> Cc: Johannes Weiner <jweiner@redhat.com> Reviewed-by: Andrea Arcangeli <aarcange@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hillf Danton [Tue, 1 Nov 2011 00:09:38 +0000 (17:09 -0700)]
mm/huge_memory: fix copying user highpage
The THP copy-on-write handler falls back to regular-sized pages for a huge
page replacement upon allocation failure or if THP has been individually
disabled in the target VMA. The loop responsible for copying page-sized
chunks accidentally uses multiples of PAGE_SHIFT instead of PAGE_SIZE as
the virtual address arg for copy_user_highpage().
Signed-off-by: Hillf Danton <dhillf@gmail.com> Acked-by: Johannes Weiner <jweiner@redhat.com> Reviewed-by: Andrea Arcangeli <aarcange@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mel Gorman [Tue, 1 Nov 2011 00:09:33 +0000 (17:09 -0700)]
vmscan: abort reclaim/compaction if compaction can proceed
If compaction can proceed, shrink_zones() stops doing any work but its
callers still call shrink_slab() which raises the priority and potentially
sleeps. This is unnecessary and wasteful so this patch aborts direct
reclaim/compaction entirely if compaction can proceed.
Signed-off-by: Mel Gorman <mgorman@suse.de> Acked-by: Rik van Riel <riel@redhat.com> Reviewed-by: Minchan Kim <minchan.kim@gmail.com> Acked-by: Johannes Weiner <jweiner@redhat.com> Cc: Josh Boyer <jwboyer@redhat.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rik van Riel [Tue, 1 Nov 2011 00:09:31 +0000 (17:09 -0700)]
vmscan: limit direct reclaim for higher order allocations
When suffering from memory fragmentation due to unfreeable pages, THP page
faults will repeatedly try to compact memory. Due to the unfreeable
pages, compaction fails.
Needless to say, at that point page reclaim also fails to create free
contiguous 2MB areas. However, that doesn't stop the current code from
trying, over and over again, and freeing a minimum of 4MB (2UL <<
sc->order pages) at every single invocation.
This resulted in my 12GB system having 2-3GB free memory, a corresponding
amount of used swap and very sluggish response times.
This can be avoided by having the direct reclaim code not reclaim from
zones that already have plenty of free memory available for compaction.
If compaction still fails due to unmovable memory, doing additional
reclaim will only hurt the system, not help.
[jweiner@redhat.com: change comment to explain the order check] Signed-off-by: Rik van Riel <riel@redhat.com> Acked-by: Johannes Weiner <jweiner@redhat.com> Acked-by: Mel Gorman <mgorman@suse.de> Cc: Andrea Arcangeli <aarcange@redhat.com> Reviewed-by: Minchan Kim <minchan.kim@gmail.com> Signed-off-by: Johannes Weiner <jweiner@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Minchan Kim [Tue, 1 Nov 2011 00:09:28 +0000 (17:09 -0700)]
vmscan: add barrier to prevent evictable page in unevictable list
When a race between putback_lru_page() and shmem_lock with lock=0 happens,
progrom execution order is as follows, but clear_bit in processor #1 could
be reordered right before spin_unlock of processor #1. Then, the page
would be stranded on the unevictable list.
spin_lock
SetPageLRU
spin_unlock
clear_bit(AS_UNEVICTABLE)
spin_lock
if PageLRU()
if !test_bit(AS_UNEVICTABLE)
move evictable list
smp_mb
if !test_bit(AS_UNEVICTABLE)
move evictable list
spin_unlock
But, pagevec_lookup() in scan_mapping_unevictable_pages() has
rcu_read_[un]lock() so it could protect reordering before reaching
test_bit(AS_UNEVICTABLE) on processor #1 so this problem never happens.
But it's a unexpected side effect and we should solve this problem
properly.
This patch adds a barrier after mapping_clear_unevictable.
I didn't meet this problem but just found during review.
Signed-off-by: Minchan Kim <minchan.kim@gmail.com> Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Cc: Mel Gorman <mel@csn.ul.ie> Cc: Rik van Riel <riel@redhat.com> Cc: Lee Schermerhorn <lee.schermerhorn@hp.com> Acked-by: Johannes Weiner <jweiner@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
warning: symbol 'memblock_overlaps_region' was not declared. Should it be static?
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers,com> Cc: Yinghai Lu <yinghai@kernel.org> Cc: "H. Peter Anvin" <hpa@linux.intel.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Tomi Valkeinen <tomi.valkeinen@nokia.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
projects / mirror_ubuntu-focal-kernel.git / log