The purpose of each TTY is as follows:
* ttyUSB0: DIAG/QCDM port.
* ttyUSB1: GNSS data.
* ttyUSB2: AT-capable port (control).
* ttyUSB3: AT-capable port (data).
In the secondary layout with PID=0x9206 (AT+CUSBSELNV=86) the module
exposes 6 TTY ports:
The purpose of each TTY is as follows:
* ttyUSB0: DIAG/QCDM port.
* ttyUSB1: GNSS data.
* ttyUSB2: AT-capable port (control).
* ttyUSB3: QFLOG interface.
* ttyUSB4: DAM interface.
* ttyUSB5: AT-capable port (data).
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es> Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
The USB composition, defining the set of exported functions, is dynamic
in newer Quectel modems. Default functions can be disabled and
alternative functions can be enabled instead. The alternatives
includes class functions using interface pairs, which should be
handled by the respective class drivers.
Active interfaces are numbered consecutively, so static
blacklisting based on interface numbers will fail when the
composition changes. An example of such an error, where the
option driver has bound to the CDC ECM data interface,
preventing cdc_ether from handling this function:
Change rules for EC21, EC25, BG96 and EG95 to match vendor specific
serial functions only, to prevent binding to class functions. Require
2 endpoints on ff/ff/ff functions, avoiding the 3 endpoint QMI/RMNET
network functions.
Cc: AceLan Kao <acelan.kao@canonical.com> Cc: Sebastian Sjoholm <ssjoholm@mac.com> Cc: Dan Williams <dcbw@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
The USB device descriptor may get changed between two consecutive
enumerations on the same device for some reason, such as DFU or
malicius device.
In that case, we may access the changing descriptor if we don't take
the device lock here.
There were some problem in ipq8074 Gen2 PCIe phy init sequence.
1. Few register values were wrongly updated in the phy init sequence.
2. The register QSERDES_RX_SIGDET_CNTRL is a RX tuning parameter
register which is added in serdes table causing the wrong register
was getting updated.
3. Clocks and resets were not added in the phy init.
Fix these to make Gen2 PCIe port on ipq8074 devices to work.
The current implementation for gbcodec_mixer_dapm_ctl_put() uses
uninitialized gbvalue for comparison with updated value. This was found
using static analysis with coverity.
Uninitialized scalar variable (UNINIT)
11. uninit_use: Using uninitialized value
gbvalue.value.integer_value[0].
460 if (gbvalue.value.integer_value[0] != val) {
This patch fixes the issue with fetching the gbvalue before using it for
comparision.
Fixes: 6339d2322c47 ("greybus: audio: Add topology parser for GB codec") Reported-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Vaibhav Agarwal <vaibhav.sr@gmail.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/bc4f29eb502ccf93cd2ffd98db0e319fa7d0f247.1597408126.git.vaibhav.sr@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
The '#ifdef MODULE' check in the original commit does not work as intended.
The code under the check is not built at all if CONFIG_DEBUG_FS=y. Fix this
by using a correct check.
Fixes: 275678e7a9be ("debugfs: Check module state before warning in {full/open}_proxy_open()") Signed-off-by: Vladis Dronov <vdronov@redhat.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200811150129.53343-1-vdronov@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
when kmalloc() fails in kvm_io_bus_unregister_dev(), before removing
the bus, we should iterate over all other devices linked to it and call
kvm_iodevice_destructor() for them
Fixes: 90db10434b16 ("KVM: kvm_io_bus_unregister_dev() should never fail") Cc: stable@vger.kernel.org Reported-and-tested-by: syzbot+f196caa45793d6374707@syzkaller.appspotmail.com Link: https://syzkaller.appspot.com/bug?extid=f196caa45793d6374707 Signed-off-by: Rustam Kovhaev <rkovhaev@gmail.com> Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20200907185535.233114-1-rkovhaev@gmail.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
For the obscure cases where PMD and PUD are the same size
(64kB pages with 42bit VA, for example, which results in only
two levels of page tables), we can't map anything as a PUD,
because there is... erm... no PUD to speak of. Everything is
either a PMD or a PTE.
So let's only try and map a PUD when its size is different from
that of a PMD.
Cc: stable@vger.kernel.org Fixes: b8e0ba7c8bea ("KVM: arm64: Add support for creating PUD hugepages at stage 2") Reported-by: Gavin Shan <gshan@redhat.com> Reported-by: Eric Auger <eric.auger@redhat.com> Reviewed-by: Alexandru Elisei <alexandru.elisei@arm.com> Reviewed-by: Gavin Shan <gshan@redhat.com> Tested-by: Gavin Shan <gshan@redhat.com> Tested-by: Eric Auger <eric.auger@redhat.com> Tested-by: Alexandru Elisei <alexandru.elisei@arm.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
According to SDM 27.2.4, Event delivery causes an APIC-access VM exit.
Don't report internal error and freeze guest when event delivery causes
an APIC-access exit, it is handleable and the event will be re-injected
during the next vmentry.
Signed-off-by: Wanpeng Li <wanpengli@tencent.com>
Message-Id: <1597827327-25055-2-git-send-email-wanpengli@tencent.com> Cc: stable@vger.kernel.org Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
Yunhai Zhang recently fixed a VGA software scrollback bug in commit ebfdfeeae8c0 ("vgacon: Fix for missing check in scrollback handling"),
but that then made people look more closely at some of this code, and
there were more problems on the vgacon side, but also the fbcon software
scrollback.
We don't really have anybody who maintains this code - probably because
nobody actually _uses_ it any more. Sure, people still use both VGA and
the framebuffer consoles, but they are no longer the main user
interfaces to the kernel, and haven't been for decades, so these kinds
of extra features end up bitrotting and not really being used.
So rather than try to maintain a likely unused set of code, I'll just
aggressively remove it, and see if anybody even notices. Maybe there
are people who haven't jumped on the whole GUI badnwagon yet, and think
it's just a fad. And maybe those people use the scrollback code.
If that turns out to be the case, we can resurrect this again, once
we've found the sucker^Wmaintainer for it who actually uses it.
This (and the VGA soft scrollback) turns out to have various nasty small
special cases that nobody really is willing to fight. The soft
scrollback code was really useful a few decades ago when you typically
used the console interactively as the main way to interact with the
machine, but that just isn't the case any more.
So it's not worth dragging along.
Tested-by: Yuan Ming <yuanmingbuaa@gmail.com> Tested-by: Willy Tarreau <w@1wt.eu> Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
If the pkey_table is not available (which is the case when RoCE is not
supported), the cited commit caused a regression where mlx4_devices
without RoCE are not created.
Fix this by returning a pkey table length of zero in procedure
eth_link_query_port() if the pkey-table length reported by the device is
zero.
Link: https://lore.kernel.org/r/20200824110229.1094376-1-leon@kernel.org Cc: <stable@vger.kernel.org> Fixes: 1901b91f9982 ("IB/core: Fix potential NULL pointer dereference in pkey cache") Fixes: fa417f7b520e ("IB/mlx4: Add support for IBoE") Signed-off-by: Mark Bloch <markb@mellanox.com> Reviewed-by: Maor Gottlieb <maorg@nvidia.com> Signed-off-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
This means that images can be mapped and unmapped (i.e. block devices
can be created and deleted) by a UID 0 process even after it drops all
privileges or by any process with CAP_DAC_OVERRIDE in its user namespace
as long as UID 0 is mapped into that user namespace.
Be consistent with other virtual block devices (loop, nbd, dm, md, etc)
and require CAP_SYS_ADMIN in the initial user namespace for mapping and
unmapping, and also for dumping the configuration string and refreshing
the image header.
Cc: stable@vger.kernel.org Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Reviewed-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
Commit b214fe592ab7 ("mmc: sdhci-of-esdhc: add erratum eSDHC7 support")
added code to check for a specific compatible string in the device-tree
on every esdhc interrupat. Instead of doing this record the quirk in
struct sdhci_esdhc and lookup the struct in esdhc_irq.
SDHCI changed from using a tasklet to finish requests, to using an IRQ
thread i.e. commit c07a48c2651965 ("mmc: sdhci: Remove finish_tasklet").
Because this increased the latency to complete requests, a preparatory
change was made to complete the request from the IRQ handler if
possible i.e. commit 19d2f695f4e827 ("mmc: sdhci: Call mmc_request_done()
from IRQ handler if possible"). That alleviated the situation for MMC
block devices because the MMC block driver makes use of mmc_pre_req()
and mmc_post_req() so that successful requests are completed in the IRQ
handler and any DMA unmapping is handled separately in mmc_post_req().
However SDIO was still affected, and an example has been reported with
up to 20% degradation in performance.
Looking at SDIO I/O helper functions, sdio_io_rw_ext_helper() appeared
to be a possible candidate for making use of asynchronous requests
within its I/O loops, but analysis revealed that these loops almost
never iterate more than once, so the complexity of the change would not
be warrented.
Instead, mmc_pre_req() and mmc_post_req() are added before and after I/O
submission (mmc_wait_for_req) in mmc_io_rw_extended(). This still has
the potential benefit of reducing the duration of interrupt handlers, as
well as addressing the latency issue for SDHCI. It also seems a more
reasonable solution than forcing drivers to do everything in the IRQ
handler.
Temporarily disable preemption on a5xx targets pending some improvements
to protect the RPTR shadow from being corrupted.
Cc: stable@vger.kernel.org Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org> Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
The TVE200 will occasionally print a bunch of lost interrupts
and similar dmesg messages, sometimes during boot and sometimes
after disabling and coming back to enablement. This is probably
because the hardware is left in an unknown state by the boot
loader that displays a logo.
This can be fixed by bringing the controller into a known state
by resetting the controller while enabling it. We retry reset 5
times like the vendor driver does. We also put the controller
into reset before de-clocking it and clear all interrupts before
enabling the vblank IRQ.
This makes the video enable/disable/enable cycle rock solid
on the D-Link DIR-685. Tested extensively.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: stable@vger.kernel.org Link: https://patchwork.freedesktop.org/patch/msgid/20200820203144.271081-1-linus.walleij@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
1. Initiator A tries to log in to iqn1-tpg1 on port 3260. After finishing
PDU exchange in the login thread and before the negotiation is finished
the the network link goes down. At this point A has not finished login
and tpg->np_login_sem is held.
2. Initiator B tries to log in to iqn2-tpg1 on port 3260. After finishing
PDU exchange in the login thread the target expects to process remaining
login PDUs in workqueue context.
3. Initiator A' tries to log in to iqn1-tpg1 on port 3260 from a new
socket. A' will wait for tpg->np_login_sem with np->np_login_timer
loaded to wait for at most 15 seconds. The lock is held by A so A'
eventually times out.
4. Before A' got timeout initiator B gets negotiation failed and calls
iscsi_target_login_drop()->iscsi_target_login_sess_out(). The
np->np_login_timer is canceled and initiator A' will hang forever.
Because A' is now in the login thread, no new login requests can be
serviced.
Fix this by moving iscsi_stop_login_thread_timer() out of
iscsi_target_login_sess_out(). Also remove iscsi_np parameter from
iscsi_target_login_sess_out().
Link: https://lore.kernel.org/r/20200729130343.24976-1-houpu@bytedance.com Cc: stable@vger.kernel.org Reviewed-by: Mike Christie <michael.christie@oracle.com> Signed-off-by: Hou Pu <houpu@bytedance.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
Current code does not consider 'page_off' in data digest calculation. To
fix this, add a local variable 'first_sg' and set first_sg.offset to
sg->offset + page_off.
Link: https://lore.kernel.org/r/1598358910-3052-1-git-send-email-varun@chelsio.com Fixes: e48354ce078c ("iscsi-target: Add iSCSI fabric support for target v4.1") Cc: <stable@vger.kernel.org> Reviewed-by: Mike Christie <michael.christie@oralce.com> Signed-off-by: Varun Prakash <varun@chelsio.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
The recent commit 7d8196641ee1 ("regulator: Remove pointer table
overallocation") changed the size of coupled_rdevs and now KASAN is able
to detect slab-out-of-bounds problem in regulator_unlock_recursive(),
which is a legit problem caused by a typo in the code. The recursive
unlock function uses n_coupled value of a parent regulator for unlocking
supply regulator, while supply's n_coupled should be used. In practice
problem may only affect platforms that use coupled regulators.
Cc: stable@vger.kernel.org # 5.0+ Fixes: f8702f9e4aa7 ("regulator: core: Use ww_mutex for regulators locking") Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Link: https://lore.kernel.org/r/20200831204335.19489-1-digetx@gmail.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
By calling device_initialize() earlier and noting that kfree(NULL) is
ok, we can save a bit of code in error handling and plug of_node leak.
Fixed commit already did part of the work.
Fixes: 9177514ce349 ("regulator: fix memory leak on error path of regulator_register()") Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Reviewed-by: Vladimir Zapolskiy <vz@mleia.com> Acked-by: Vladimir Zapolskiy <vz@mleia.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/f5035b1b4d40745e66bacd571bbbb5e4644d21a1.1597195321.git.mirq-linux@rere.qmqm.pl Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
Pull regulator_list_mutex into set_consumer_device_supply() and keep
allocations outside of it. Fourth of the fs_reclaim deadlock case.
Fixes: 45389c47526d ("regulator: core: Add early supply resolution for regulators") Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/f0380bdb3d60aeefa9693c4e234d2dcda7e56747.1597195321.git.mirq-linux@rere.qmqm.pl Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
Fixes: f8702f9e4aa7 ("regulator: core: Use ww_mutex for regulators locking") Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/6eebc99b2474f4ffaa0405b15178ece0e7e4f608.1597195321.git.mirq-linux@rere.qmqm.pl Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
Allocating memory with regulator_list_mutex held makes lockdep unhappy
when memory pressure makes the system do fs_reclaim on eg. eMMC using
a regulator. Push the lock inside regulator_init_coupling() after the
allocation.
======================================================
WARNING: possible circular locking dependency detected
5.7.13+ #533 Not tainted
------------------------------------------------------
kswapd0/383 is trying to acquire lock: cca78ca4 (&sbi->write_io[i][j].io_rwsem){++++}-{3:3}, at: __submit_merged_write_cond+0x104/0x154
but task is already holding lock: c0e38518 (fs_reclaim){+.+.}-{0:0}, at: __fs_reclaim_acquire+0x0/0x50
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #2 (fs_reclaim){+.+.}-{0:0}:
fs_reclaim_acquire.part.11+0x40/0x50
fs_reclaim_acquire+0x24/0x28
__kmalloc+0x54/0x218
regulator_register+0x860/0x1584
dummy_regulator_probe+0x60/0xa8
[...]
other info that might help us debug this:
The commit 079ad2fb4bf9 ("kobject: Avoid premature parent object freeing in
kobject_cleanup()") inadvertently dropped a possibility to call kobject_del()
with NULL pointer. Restore the old behaviour.
Fixes: 079ad2fb4bf9 ("kobject: Avoid premature parent object freeing in kobject_cleanup()") Cc: stable <stable@vger.kernel.org> Reported-by: Qu Wenruo <quwenruo.btrfs@gmx.com> Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Qu Wenruo <wqu@suse.com> Link: https://lore.kernel.org/r/20200803082706.65347-1-andriy.shevchenko@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
When faulting in the pages for the user supplied buffer for the search
ioctl, we are passing only the base address of the buffer to the function
fault_in_pages_writeable(). This means that after the first iteration of
the while loop that searches for leaves, when we have a non-zero offset,
stored in 'sk_offset', we try to fault in a wrong page range.
So fix this by adding the offset in 'sk_offset' to the base address of the
user supplied buffer when calling fault_in_pages_writeable().
Several users have reported that the applications compsize and bees have
started to operate incorrectly since commit a48b73eca4ceb9 ("btrfs: fix
potential deadlock in the search ioctl") was added to stable trees, and
these applications make heavy use of the search ioctls. This fixes their
issues.
Link: https://lore.kernel.org/linux-btrfs/632b888d-a3c3-b085-cdf5-f9bb61017d92@lechevalier.se/ Link: https://github.com/kilobyte/compsize/issues/34 Fixes: a48b73eca4ceb9 ("btrfs: fix potential deadlock in the search ioctl") CC: stable@vger.kernel.org # 4.4+ Tested-by: A L <mail@lechevalier.se> Reviewed-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
Nikolay reported a lockdep splat in generic/476 that I could reproduce
with btrfs/187.
======================================================
WARNING: possible circular locking dependency detected
5.9.0-rc2+ #1 Tainted: G W
------------------------------------------------------
kswapd0/100 is trying to acquire lock: ffff9e8ef38b6268 (&delayed_node->mutex){+.+.}-{3:3}, at: __btrfs_release_delayed_node.part.0+0x3f/0x330
but task is already holding lock: ffffffffa9d74700 (fs_reclaim){+.+.}-{0:0}, at: __fs_reclaim_acquire+0x5/0x30
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
This is because we are holding the chunk_mutex when we call
btrfs_alloc_device, which does a GFP_KERNEL allocation. We don't want
to switch that to a GFP_NOFS lock because this is the only place where
it matters. So instead use memalloc_nofs_save() around the allocation
in order to avoid the lockdep splat.
Reported-by: Nikolay Borisov <nborisov@suse.com> CC: stable@vger.kernel.org # 4.4+ Reviewed-by: Anand Jain <anand.jain@oracle.com> Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
[BUG]
A completely sane converted fs will cause kernel warning at balance
time:
[ 1557.188633] BTRFS info (device sda7): relocating block group 8162107392 flags data
[ 1563.358078] BTRFS info (device sda7): found 11722 extents
[ 1563.358277] BTRFS info (device sda7): leaf 7989321728 gen 95 total ptrs 213 free space 3458 owner 2
[ 1563.358280] item 0 key (7984947200 169 0) itemoff 16250 itemsize 33
[ 1563.358281] extent refs 1 gen 90 flags 2
[ 1563.358282] ref#0: tree block backref root 4
[ 1563.358285] item 1 key (7985602560 169 0) itemoff 16217 itemsize 33
[ 1563.358286] extent refs 1 gen 93 flags 258
[ 1563.358287] ref#0: shared block backref parent 7985602560
[ 1563.358288] (parent 7985602560 is NOT ALIGNED to nodesize 16384)
[ 1563.358290] item 2 key (7985635328 169 0) itemoff 16184 itemsize 33
...
[ 1563.358995] BTRFS error (device sda7): eb 7989321728 invalid extent inline ref type 182
[ 1563.358996] ------------[ cut here ]------------
[ 1563.359005] WARNING: CPU: 14 PID: 2930 at 0xffffffff9f231766
Then with transaction abort, and obviously failed to balance the fs.
[CAUSE]
That mentioned inline ref type 182 is completely sane, it's
BTRFS_SHARED_BLOCK_REF_KEY, it's some extra check making kernel to
believe it's invalid.
Commit 64ecdb647ddb ("Btrfs: add one more sanity check for shared ref
type") introduced extra checks for backref type.
One of the requirement is, parent bytenr must be aligned to node size,
which is not correct.
One example is like this:
0 1G 1G+4K 2G 2G+4K
| |///////////////////|//| <- A chunk starts at 1G+4K
| | <- A tree block get reserved at bytenr 1G+4K
Then we have a valid tree block at bytenr 1G+4K, but not aligned to
nodesize (16K).
Such chunk is not ideal, but current kernel can handle it pretty well.
We may warn about such tree block in the future, but should not reject
them.
[FIX]
Change the alignment requirement from node size alignment to sector size
alignment.
Also, to make our lives a little easier, also output @iref when
btrfs_get_extent_inline_ref_type() failed, so we can locate the item
easier.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=205475 Fixes: 64ecdb647ddb ("Btrfs: add one more sanity check for shared ref type") CC: stable@vger.kernel.org # 4.14+ Reviewed-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Qu Wenruo <wqu@suse.com>
[ update comments and messages ] Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
let's use usb_find_common_endpoints() to discover endpoints, it does all
necessary checks for type and xfer direction
remove memset() in hfa384x_create(), because we now assign endpoints in
prism2sta_probe_usb() and because create_wlan() uses kzalloc() to
allocate hfa384x struct before calling hfa384x_create()
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses a 16 byte u8 array on the stack. As Lars also noted
this anti pattern can involve a leak of data to userspace and that
indeed can happen here. We close both issues by moving to
a suitable structure in the iio_priv() data with alignment
ensured by use of an explicit c structure. This data is allocated
with kzalloc so no data can leak appart from previous readings.
The additional forcing of the 8 byte alignment of the timestamp
is not strictly necessary but makes the code less fragile by
making this explicit.
Fixes: c7eeea93ac60 ("iio: Add Freescale MMA8452Q 3-axis accelerometer driver") Reported-by: Lars-Peter Clausen <lars@metafoo.de> Cc: Peter Meerwald <pmeerw@pmeerw.net> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses a 16 byte u8 array on the stack As Lars also noted
this anti pattern can involve a leak of data to userspace and that
indeed can happen here. We close both issues by moving to
a suitable structure in the iio_priv() data with alignment
ensured by use of an explicit c structure. This data is allocated
with kzalloc so no data can leak appart from previous readings.
The force alignment of ts is not strictly necessary in this particularly
case but does make the code less fragile.
Fixes: a84ef0d181d9 ("iio: accel: add Freescale MMA7455L/MMA7456L 3-axis accelerometer driver") Reported-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Cc: <Stable@vger.kernel.org> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
iio_push_to_buffers_with_timestamp assumes 8 byte alignment which
is not guaranteed by an array of smaller elements.
Note that whilst in this particular case the alignment forcing
of the ts element is not strictly necessary it acts as good
documentation. Doing this where not necessary should cut
down on the number of cut and paste introduced errors elsewhere.
Fixes: 0427a106a98a ("iio: accel: kxsd9: Add triggered buffer handling") Reported-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses an array of smaller elements on the stack.
As Lars also noted this anti pattern can involve a leak of data to
userspace and that indeed can happen here. We close both issues by
moving to a suitable structure in the iio_priv() data with alignment
explicitly requested. This data is allocated with kzalloc so no
data can leak appart from previous readings.
The explicit alignment of ts is necessary to ensure consistent
padding for x86_32 in which the ts would otherwise be 4 byte aligned.
Fixes: 283d26917ad6 ("iio: chemical: ccs811: Add triggered buffer support") Reported-by: Lars-Peter Clausen <lars@metafoo.de> Cc: Narcisa Ana Maria Vasile <narcisaanamaria12@gmail.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses a 16 byte array of smaller elements on the stack.
As Lars also noted this anti pattern can involve a leak of data to
userspace and that indeed can happen here. We close both issues by
moving to a suitable structure in the iio_priv().
This data is allocated with kzalloc so no data can leak appart
from previous readings.
It is necessary to force the alignment of ts to avoid the padding
on x86_32 being different from 64 bit platorms (it alows for
4 bytes aligned 8 byte types.
Fixes: 06ad7ea10e2b ("max44000: Initial triggered buffer support") Reported-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses an array of smaller elements on the stack.
As Lars also noted this anti pattern can involve a leak of data to
userspace and that indeed can happen here. We close both issues by
moving to a suitable structure in the iio_priv() data.
This data is allocated with kzalloc so no data can leak apart from
previous readings.
The explicit alignment of ts is not necessary in this case as by
coincidence the padding will end up the same, however I consider
it to make the code less fragile and have included it.
Fixes: bc11ca4a0b84 ("iio:magnetometer:ak8975: triggered buffer support") Reported-by: Lars-Peter Clausen <lars@metafoo.de> Cc: Gregor Boirie <gregor.boirie@parrot.com> Cc: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses an array of smaller elements on the stack.
As Lars also noted this anti pattern can involve a leak of data to
userspace and that indeed can happen here. We close both issues by
moving to a suitable structure in the iio_priv().
This data is allocated with kzalloc so no data can leak apart
from previous readings.
The eplicit alignment of ts is necessary to ensure correct padding
on x86_32 where s64 is only aligned to 4 bytes.
Fixes: 08e05d1fce5c ("ti-adc081c: Initial triggered buffer support") Reported-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses an array of smaller elements on the stack.
As Lars also noted this anti pattern can involve a leak of data to
userspace and that indeed can happen here. We close both issues by
moving to a suitable structure in the iio_priv() data.
This data is allocated with kzalloc so no data can leak apart
from previous readings.
The explicit alignment of ts is necessary to ensure correct padding
on architectures where s64 is only 4 bytes aligned such as x86_32.
Fixes: a9e9c7153e96 ("iio: adc: add max1117/max1118/max1119 ADC driver") Reported-by: Lars-Peter Clausen <lars@metafoo.de> Cc: Akinobu Mita <akinobu.mita@gmail.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses a 32 byte array of smaller elements on the stack.
As Lars also noted this anti pattern can involve a leak of data to
userspace and that indeed can happen here. We close both issues by
moving to a suitable structure in the iio_priv() data with alignment
explicitly requested. This data is allocated with kzalloc so no
data can leak apart from previous readings. The explicit alignment
isn't technically needed here, but it reduced fragility and avoids
cut and paste into drivers where it will be needed.
If we want this in older stables will need manual backport due to
driver reworks.
Fixes: c43a102e67db ("iio: ina2xx: add support for TI INA2xx Power Monitors") Reported-by: Lars-Peter Clausen <lars@metafoo.de> Cc: Stefan Brüns <stefan.bruens@rwth-aachen.de> Cc: Marc Titinger <mtitinger@baylibre.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses an array of smaller elements on the stack.
As Lars also noted this anti pattern can involve a leak of data to
userspace and that indeed can happen here. We close both issues by
moving to a suitable structure in the iio_priv().
This data is allocated with kzalloc so no data can leak apart from
previous readings.
The force alignment of ts is not strictly necessary in this case
but reduces the fragility of the code.
Fixes: 3691e5a69449 ("iio: adc: add driver for the ti-adc084s021 chip") Reported-by: Lars-Peter Clausen <lars@metafoo.de> Cc: Mårten Lindahl <martenli@axis.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses a 16 byte array of smaller elements on the stack.
As Lars also noted this anti pattern can involve a leak of data to
userspace and that indeed can happen here. We close both issues by moving
to a suitable structure in the iio_priv() data with alignment
ensured by use of an explicit c structure. This data is allocated
with kzalloc so no data can leak appart from previous readings.
Fixes tag is beyond some major refactoring so likely manual backporting
would be needed to get that far back.
Whilst the force alignment of the ts is not strictly necessary, it
does make the code less fragile.
Fixes: 3bbec9773389 ("iio: bmc150_accel: add support for hardware fifo") Reported-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses a 16 byte s16 array on the stack As Lars also noted
this anti pattern can involve a leak of data to userspace and that
indeed can happen here. We close both issues by moving to
a suitable structure in the iio_priv() data with alignment
ensured by use of an explicit c structure. This data is allocated
with kzalloc so no data can leak appart from previous readings.
In this case the forced alignment of the ts is necessary to ensure
correct padding on x86_32 where the s64 would only be 4 byte aligned.
Fixes: 16b05261537e ("mb1232.c: add distance iio sensor with i2c") Reported-by: Lars-Peter Clausen <lars@metafoo.de> Cc: Andreas Klinger <ak@it-klinger.de> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Cc: <Stable@vger.kernel.org> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses an array of smaller elements on the stack.
Here we use a structure on the stack. The driver already did an
explicit memset so no data leak was possible.
Forced alignment of ts is not strictly necessary but probably makes
the code slightly less fragile.
Note there has been some rework in this driver of the years, so no
way this will apply cleanly all the way back.
Fixes: 2690be905123 ("iio: Add Lite-On ltr501 ambient light / proximity sensor driver") Reported-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
BMI160 Minimium gyroscope frequency in normal mode is 25Hz.
When older EC firmware do not report their sensors frequencies,
use 25Hz as the minimum for gyroscope to be sure it works on BMI160.
Fixes: ae7b02ad2f32d ("iio: common: cros_ec_sensors: Expose cros_ec_sensors frequency range via iio sysfs") Signed-off-by: Gwendal Grignou <gwendal@chromium.org> Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
To stop conversion ads1015_set_power_state() function call unimplemented
function __pm_runtime_suspend() from pm_runtime_put_autosuspend()
if CONFIG_PM is not set.
In case of CONFIG_PM is not set: __pm_runtime_suspend() returns -ENOSYS,
so ads1015_read_raw() failed because ads1015_set_power_state() returns an
error.
If CONFIG_PM is disabled, there is no need to start/stop conversion.
Fix it by adding return 0 function variant if CONFIG_PM is not set.
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru> Fixes: ecc24e72f437 ("iio: adc: Add TI ADS1015 ADC driver support") Tested-by: Maxim Kiselev <bigunclemax@gmail.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
When memory encryption is active the device is likely not in a direct
mapped domain. Forbid using IOMMUv2 functionality for now until finer
grained checks for this have been implemented.
On my R9 390, the voltage was reported as a constant 1000 mV.
This was due to a bug in smu7_hwmgr.c, in the smu7_read_sensor()
function, where some magic constants were used in a condition,
to determine whether the voltage should be read from PLANE2_VID
or PLANE1_VID. The VDDC mask was incorrectly used, instead of
the VDDGFX mask.
This patch changes the code to use the correct defined constants
(and apply the correct bitshift), thus resulting in correct voltage reporting.
Signed-off-by: Sandeep Raghuraman <sandy.8925@gmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
In snd_hdac_device_init pm_runtime_set_active is called to
increase child_count in parent device. But when it is failed
to build connection with GPU for one case that integrated
graphic gpu is disabled, snd_hdac_ext_bus_device_exit will be
invoked to clean up a HD-audio extended codec base device. At
this time the child_count of parent is not decreased, which
makes parent device can't get suspended.
This patch calls pm_runtime_set_suspended to decrease child_count
in parent device in snd_hdac_device_exit to match with
snd_hdac_device_init. pm_runtime_set_suspended can make sure that
it will not decrease child_count if the device is already suspended.
In the arm64 module linker script, the section .text.ftrace_trampoline
is specified unconditionally regardless of whether CONFIG_DYNAMIC_FTRACE
is enabled (this is simply due to the limitation that module linker
scripts are not preprocessed like the vmlinux one).
Normally, for .plt and .text.ftrace_trampoline, the section flags
present in the module binary wouldn't matter since module_frob_arch_sections()
would assign them manually anyway. However, the arm64 module loader only
sets the section flags for .text.ftrace_trampoline when CONFIG_DYNAMIC_FTRACE=y.
That's only become problematic recently due to a recent change in
binutils-2.35, where the .text.ftrace_trampoline section (along with the
.plt section) is now marked writable and executable (WAX).
We no longer allow writable and executable sections to be loaded due to
commit 5c3a7db0c7ec ("module: Harden STRICT_MODULE_RWX"), so this is
causing all modules linked with binutils-2.35 to be rejected under arm64.
Drop the IS_ENABLED(CONFIG_DYNAMIC_FTRACE) check in module_frob_arch_sections()
so that the section flags for .text.ftrace_trampoline get properly set to
SHF_EXECINSTR|SHF_ALLOC, without SHF_WRITE.
This fixes the behavior of the scaling_max_freq and scaling_min_freq
sysfs files in systems which had turbo disabled by the BIOS.
Caleb noticed that the HWP is programmed to operate in the wrong
P-state range on his system when the CPUFREQ policy min/max frequency
is set via sysfs. This seems to be because in his system
intel_pstate_get_hwp_max() is returning the maximum turbo P-state even
though turbo was disabled by the BIOS, which causes intel_pstate to
scale kHz frequencies incorrectly e.g. setting the maximum turbo
frequency whenever the maximum guaranteed frequency is requested via
sysfs.
Tested-by: Caleb Callaway <caleb.callaway@intel.com> Signed-off-by: Francisco Jerez <currojerez@riseup.net> Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[ rjw: Minor subject edits ] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
After commit f6ebbcf08f37 ("cpufreq: intel_pstate: Implement passive
mode with HWP enabled") it is possible to change the driver status
to "off" via sysfs with HWP enabled, which effectively causes the
driver to unregister itself, but HWP remains active and it forces the
minimum performance, so even if another cpufreq driver is loaded,
it will not be able to control the CPU frequency.
For this reason, make the driver refuse to change the status to
"off" with HWP enabled.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
HSDK board has Micrel KSZ9031, recent commit bcf3440c6dd ("net: phy: micrel: add phy-mode support for the KSZ9031 PHY")
caused a breakdown of Ethernet.
Using 'phy-mode = "rgmii"' is not correct because accodring RGMII
specification it is necessary to have delay on RX (PHY to MAX)
which is not generated in case of "rgmii".
Using "rgmii-id" adds necessary delay and solves the issue.
Also adding name of PHY placed on HSDK board.
Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com> Cc: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Cc: Alexey Brodkin <abrodkin@synopsys.com> Signed-off-by: Vineet Gupta <vgupta@synopsys.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
When input_mt_init_slots() fails, input should be freed
to prevent memleak. When input_register_device() fails,
we should call input_mt_destroy_slots() to free memory
allocated by input_mt_init_slots().
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
This driver didn't set hard_header_len. This patch sets hard_header_len
for it according to its header_ops->create function.
This driver's header_ops->create function (cisco_hard_header) creates
a header of (struct hdlc_header), so hard_header_len should be set to
sizeof(struct hdlc_header).
Cc: Martin Schiller <ms@dev.tdt.de> Signed-off-by: Xie He <xie.he.0141@gmail.com> Acked-by: Krzysztof Halasa <khc@pm.waw.pl> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
The Saitek X52 family of joysticks has a pair of axes that were
originally (by the Windows driver) used as mouse pointer controls. The
corresponding usage page is the Game Controls page, which is not
recognized by the generic HID driver, and therefore, both axes get
mapped to ABS_MISC. The quirk makes the second axis get mapped to
ABS_MISC+1, and therefore made available separately.
One Saitek X52 device is already fixed. This patch fixes the other two
known devices with VID/PID 06a3:0255 and 06a3:0762.
This patch addresses an irq free warning and null pointer dereference
error problem when nvme devices got timeout error during initialization.
This problem happens when nvme_timeout() function is called while
nvme_reset_work() is still in execution. This patch fixed the problem by
setting flag of the problematic request to NVME_REQ_CANCELLED before
calling nvme_dev_disable() to make sure __nvme_submit_sync_cmd() returns
an error code and let nvme_submit_sync_cmd() fail gracefully.
The following is console output.
If the controller becomes unresponsive in the middle of a reset, we
will hang because we are waiting for the freeze to complete, but that
cannot happen since we have commands that are inflight holding the
q_usage_counter, and we can't blindly fail requests that times out.
So give a timeout and if we cannot wait for queue freeze before
unfreezing, fail and have the error handling take care how to
proceed (either schedule a reconnect of remove the controller).
Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
When a request times out in a LIVE state, we simply trigger error
recovery and let the error recovery handle the request cancellation,
however when a request times out in a non LIVE state, we make sure to
complete it immediately as it might block controller setup or teardown
and prevent forward progress.
However tearing down the entire set of I/O and admin queues causes
freeze/unfreeze imbalance (q->mq_freeze_depth) because and is really
an overkill to what we actually need, which is to just fence controller
teardown that may be running, stop the queue, and cancel the request if
it is not already completed.
Now that we have the controller teardown_lock, we can safely serialize
request cancellation. This addresses a hang caused by calling extra
queue freeze on controller namespaces, causing unfreeze to not complete
correctly.
Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: James Smart <james.smart@broadcom.com> Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
In the timeout handler we may need to complete a request because the
request that timed out may be an I/O that is a part of a serial sequence
of controller teardown or initialization. In order to complete the
request, we need to fence any other context that may compete with us
and complete the request that is timing out.
In this case, we could have a potential double completion in case
a hard-irq or a different competing context triggered error recovery
and is running inflight request cancellation concurrently with the
timeout handler.
Protect using a ctrl teardown_lock to serialize contexts that may
complete a cancelled request due to error recovery or a reset.
Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: James Smart <james.smart@broadcom.com> Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
If the controller becomes unresponsive in the middle of a reset, we will
hang because we are waiting for the freeze to complete, but that cannot
happen since we have commands that are inflight holding the
q_usage_counter, and we can't blindly fail requests that times out.
So give a timeout and if we cannot wait for queue freeze before
unfreezing, fail and have the error handling take care how to proceed
(either schedule a reconnect of remove the controller).
Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
When a request times out in a LIVE state, we simply trigger error
recovery and let the error recovery handle the request cancellation,
however when a request times out in a non LIVE state, we make sure to
complete it immediately as it might block controller setup or teardown
and prevent forward progress.
However tearing down the entire set of I/O and admin queues causes
freeze/unfreeze imbalance (q->mq_freeze_depth) because and is really
an overkill to what we actually need, which is to just fence controller
teardown that may be running, stop the queue, and cancel the request if
it is not already completed.
Now that we have the controller teardown_lock, we can safely serialize
request cancellation. This addresses a hang caused by calling extra
queue freeze on controller namespaces, causing unfreeze to not complete
correctly.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
In the timeout handler we may need to complete a request because the
request that timed out may be an I/O that is a part of a serial sequence
of controller teardown or initialization. In order to complete the
request, we need to fence any other context that may compete with us
and complete the request that is timing out.
In this case, we could have a potential double completion in case
a hard-irq or a different competing context triggered error recovery
and is running inflight request cancellation concurrently with the
timeout handler.
Protect using a ctrl teardown_lock to serialize contexts that may
complete a cancelled request due to error recovery or a reset.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
Users can detect if the wait has completed or not and take appropriate
actions based on this information (e.g. weather to continue
initialization or rather fail and schedule another initialization
attempt).
Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
NVME_CTRL_NEW should never see any I/O, because in order to start
initialization it has to transition to NVME_CTRL_CONNECTING and from
there it will never return to this state.
Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
When handling commands without in-capsule data, we assign the ttag
assuming we already have the queue commands array allocated (based
on the queue size information in the connect data payload). However
if the connect itself did not send the connect data in-capsule we
have yet to allocate the queue commands,and we will assign a bogus
ttag and suffer a NULL dereference when we receive the corresponding
h2cdata pdu.
Fix this by checking if we already allocated commands before
dereferencing it when handling h2cdata, if we didn't, its for sure a
connect and we should use the preallocated connect command.
Signed-off-by: Ziye Yang <ziye.yang@intel.com> Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
eznps driver is supposed to be platform independent however it ends up
including stuff from inside arch/arc headers leading to rand config
build errors.
The quick hack to fix this (proper fix is too much chrun for non active
user-base) is to add following to nps platform agnostic header.
- copy AUX_IENABLE from arch/arc header
- move CTOP_AUX_IACK from arch/arc/plat-eznps/*/**
Reported-by: kernel test robot <lkp@intel.com> Reported-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Link: https://lkml.kernel.org/r/20200824095831.5lpkmkafelnvlpi2@linutronix.de Signed-off-by: Vineet Gupta <vgupta@synopsys.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
Don't leak kernel memory contents into the shortform attr fork.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Eric Sandeen <sandeen@redhat.com> Reviewed-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
Set the skb's network_header before it is passed to the underlying
Ethernet device for transmission.
This patch fixes the following issue:
When we use this driver with AF_PACKET sockets, there would be error
messages of:
protocol 0805 is buggy, dev (Ethernet interface name)
printed in the system "dmesg" log.
This is because skbs passed down to the Ethernet device for transmission
don't have their network_header properly set, and the dev_queue_xmit_nit
function in net/core/dev.c complains about this.
Reason of setting the network_header to this place (at the end of the
Ethernet header, and at the beginning of the Ethernet payload):
Because when this driver receives an skb from the Ethernet device, the
network_header is also set at this place.
Cc: Martin Schiller <ms@dev.tdt.de> Signed-off-by: Xie He <xie.he.0141@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
The inode chunk allocation transaction reserves inobt_maxlevels-1
blocks to accommodate a full split of the inode btree. A full split
requires an allocation for every existing level and a new root
block, which means inobt_maxlevels is the worst case block
requirement for a transaction that inserts to the inobt. This can
lead to a transaction block reservation overrun when tmpfile
creation allocates an inode chunk and expands the inobt to its
maximum depth. This problem has been observed in conjunction with
overlayfs, which makes frequent use of tmpfiles internally.
The existing reservation code goes back as far as the Linux git repo
history (v2.6.12). It was likely never observed as a problem because
the traditional file/directory creation transactions also include
worst case block reservation for directory modifications, which most
likely is able to make up for a single block deficiency in the inode
allocation portion of the calculation. tmpfile support is relatively
more recent (v3.15), less heavily used, and only includes the inode
allocation block reservation as tmpfiles aren't linked into the
directory tree on creation.
Fix up the inode alloc block reservation macro and a couple of the
block allocator minleft parameters that enforce an allocation to
leave enough free blocks in the AG for a full inobt split.
Signed-off-by: Brian Foster <bfoster@redhat.com> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
when skb->encapsulation is 0, skb->ip_summed is CHECKSUM_PARTIAL
and it is udp packet, which has a dest port as the IANA assigned.
the hardware is expected to do the checksum offload, but the
hardware will not do the checksum offload when udp dest port is
6081.
This patch fixes it by doing the checksum in software.
Reported-by: Li Bing <libing@winhong.com> Signed-off-by: Yi Li <yili@winhong.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
In probe, IRQ is requested before zchan->id is initialized which can be
read in the irq handler. Hence, shift request irq after other initializations
complete.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Madhuparna Bhowmik <madhuparnabhowmik10@gmail.com> Reviewed-by: Paul Cercueil <paul@crapouillou.net> Link: https://lore.kernel.org/r/20200821034423.12713-1-madhuparnabhowmik10@gmail.com Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
The WAKEEN bits are used to indicate which bits in the
STATESTS register may cause wake event during the codec
state change request. Configure the WAKEEN register for
the Tegra to detect the wake events.
The Tegra HDA codec HW implementation has an issue related to not
swapping the 2 channel Audio Sample Packet(ASP) channel mapping.
Whatever the FL and FR mapping specified the left channel always
comes out of left speaker and right channel on right speaker. So
add condition to disallow the swapping of FL,FR during the playback.
When make_rate() fails, vcc should be freed just
like other error paths in fs_open().
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
When down_killable() fails, skb_resp should be freed
just like when st95hf_spi_send() fails.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
The underlying Ethernet device may request necessary tailroom to be
allocated by setting needed_tailroom. This driver should also set
needed_tailroom to request the tailroom needed by the underlying
Ethernet device to be allocated.
Cc: Willem de Bruijn <willemdebruijn.kernel@gmail.com> Cc: Martin Schiller <ms@dev.tdt.de> Signed-off-by: Xie He <xie.he.0141@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
If an sctp connection gets re-used, heartbeats are flagged as invalid
because their vtag doesn't match.
Handle this in a similar way as TCP conntrack when it suspects that the
endpoints and conntrack are out-of-sync.
When a HEARTBEAT request fails its vtag validation, flag this in the
conntrack state and accept the packet.
When a HEARTBEAT_ACK is received with an invalid vtag in the reverse
direction after we allowed such a HEARTBEAT through, assume we are
out-of-sync and re-set the vtag info.
v2: remove left-over snippet from an older incarnation that moved
new_state/old_state assignments, thats not needed so keep that
as-is.
Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
The acpi_get_table() should be coupled with acpi_put_table() if
the mapped table is not used at runtime to release the table
mapping, put the CSRT table buf after using it.
Newer version of HSDK aka HSDK-4xD (with dual issue HS48x4 CPU) wired up
the perf interrupt, so enable that in DT.
This is OK for old HSDK where this irq is ignored because pct irq is not
wired up in hardware.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
Currently we allocate rx buffers in a single contiguous buffers for
headers (iser and iscsi) and data trailer. This means that most likely the
data starting offset is aligned to 76 bytes (size of both headers).
This worked fine for years, but at some point this broke, resulting in
data corruptions in isert when a command comes with immediate data and the
underlying backend device assumes 512 bytes buffer alignment.
We assume a hard-requirement for all direct I/O buffers to be 512 bytes
aligned. To fix this, we should avoid passing unaligned buffers for I/O.
Instead, we allocate our recv buffers with some extra space such that we
can have the data portion align to 512 byte boundary. This also means that
we cannot reference headers or data using structure but rather
accessors (as they may move based on alignment). Also, get rid of the
wrong __packed annotation from iser_rx_desc as this has only harmful
effects (not aligned to anything).
This affects the rx descriptors for iscsi login and data plane.
Fixes: 3d75ca0adef4 ("block: introduce multi-page bvec helpers") Link: https://lore.kernel.org/r/20200904195039.31687-1-sagi@grimberg.me Reported-by: Stephen Rust <srust@blockbridge.com> Tested-by: Doug Dumitru <doug@dumitru.com> Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
If we hit the UINT_MAX limit of bio->bi_iter.bi_size and so we are anyway
not merging this page in this bio, then it make sense to make same_page
also as false before returning.
Without this patch, we hit below WARNING in iomap.
This mostly happens with very large memory system and / or after tweaking
vm dirty threshold params to delay writeback of dirty data.
Right now we are failing requests based on the controller state (which
is checked inline in nvmf_check_ready) however we should definitely
accept requests if the queue is live.
When entering controller reset, we transition the controller into
NVME_CTRL_RESETTING, and then return BLK_STS_RESOURCE for non-mpath
requests (have blk_noretry_request set).
This is also the case for NVME_REQ_USER for the wrong reason. There
shouldn't be any reason for us to reject this I/O in a controller reset.
We do want to prevent passthru commands on the admin queue because we
need the controller to fully initialize first before we let user passthru
admin commands to be issued.
In a non-mpath setup, this means that the requests will simply be
requeued over and over forever not allowing the q_usage_counter to drop
its final reference, causing controller reset to hang if running
concurrently with heavy I/O.
Fixes: 35897b920c8a ("nvme-fabrics: fix and refine state checks in __nvmf_check_ready") Reviewed-by: James Smart <james.smart@broadcom.com> Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
The 'spi_stm32 44004000.spi: Communication suspended' message means that
when using PIO, the kernel did not read the FIFO fast enough and so the
SPI controller paused the transfer. Currently, this is printed on every
single such event, so if the kernel is busy and the controller is pausing
the transfers often, the kernel will be all the more busy scrolling this
message into the log buffer every few milliseconds. That is not helpful.
Instead, rate-limit the message and print it every once in a while. It is
not possible to use the default dev_warn_ratelimited(), because that is
still too verbose, as it prints 10 lines (DEFAULT_RATELIMIT_BURST) every
5 seconds (DEFAULT_RATELIMIT_INTERVAL). The policy here is to print 1 line
every 50 seconds (DEFAULT_RATELIMIT_INTERVAL * 10), because 1 line is more
than enough and the cycles saved on printing are better left to the CPU to
handle the SPI. However, dev_warn_once() is also not useful, as the user
should be aware that this condition is possibly recurring or ongoing. Thus
the custom rate-limit policy.
Finally, turn the message from dev_warn() to dev_dbg(), since the system
does not suffer any sort of malfunction if this message appears, it is
just slowing down. This further reduces the printing into the log buffer
and frees the CPU to do useful work.
Fixes: dcbe0d84dfa5 ("spi: add driver for STM32 SPI controller") Signed-off-by: Marek Vasut <marex@denx.de> Cc: Alexandre Torgue <alexandre.torgue@st.com> Cc: Amelie Delaunay <amelie.delaunay@st.com> Cc: Antonio Borneo <borneo.antonio@gmail.com> Cc: Mark Brown <broonie@kernel.org> Link: https://lore.kernel.org/r/20200905151913.117775-1-marex@denx.de Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
As the comments in this patch say, if we tune and find all phases are
valid it's _almost_ as bad as no phases being found valid. Probably
all phases are not really reliable but we didn't detect where the
unreliable place is. That means we'll essentially be guessing and
hoping we get a good phase.
This is not just a problem in theory. It was causing real problems on
a real board. On that board, most often phase 10 is found as the only
invalid phase, though sometimes 10 and 11 are invalid and sometimes
just 11. Some percentage of the time, however, all phases are found
to be valid. When this happens, the current logic will decide to use
phase 11. Since phase 11 is sometimes found to be invalid, this is a
bad choice. Sure enough, when phase 11 is picked we often get mmc
errors later in boot.
I have seen cases where all phases were found to be valid 3 times in a
row, so increase the retry count to 10 just to be extra sure.
Fixes: 415b5a75da43 ("mmc: sdhci-msm: Add platform_execute_tuning implementation") Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/20200827075809.1.If179abf5ecb67c963494db79c3bc4247d987419b@changeid Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>
The commit 61d7437ed1390 ("mmc: sdhci-acpi: Fix HS400 tuning for AMDI0040")
broke resume for eMMC HS400. When the system suspends the eMMC controller
is powered down. So, on resume we need to reinitialize the controller.
Although, amd_sdhci_host was not getting cleared, so the DLL was never
re-enabled on resume. This results in HS400 being non-functional.
To fix the problem, this change clears the tuned_clock flag, clears the
dll_enabled flag and disables the DLL on reset.
Fixes: 61d7437ed1390 ("mmc: sdhci-acpi: Fix HS400 tuning for AMDI0040") Signed-off-by: Raul E Rangel <rrangel@chromium.org> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/20200831150517.1.I93c78bfc6575771bb653c9d3fca5eb018a08417d@changeid Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: William Breathitt Gray <william.gray@canonical.com>