Nikola Cornij [Tue, 23 Jul 2019 20:38:02 +0000 (16:38 -0400)]
drm/amd/display: Remove 4:2:2 DSC support
[why]
If DSC is available, a higher picture quality is achieved by using
DSC with 4:4:4 format. Using 4:2:2 instead does not offer any benefit
and would only introduce loss of quality. Removing it reduces
maintenance and testing effort.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com> Reviewed-by: Jun Lei <Jun.Lei@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Lewis Huang [Mon, 22 Jul 2019 19:23:32 +0000 (15:23 -0400)]
drm/amd/display: reprogram VM config when system resume
[Why]
The vm config will be clear to 0 when system enter S4. It will
cause hubbub didn't know how to fetch data when system resume.
The flip always pending because earliest_inuse_address and
request_address are different.
[How]
Reprogram VM config when system resume
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com> Reviewed-by: Jun Lei <Jun.Lei@amd.com> Acked-by: Eric Yang <eric.yang2@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Eric Yang [Thu, 11 Jul 2019 02:41:51 +0000 (22:41 -0400)]
drm/amd/display: Enable type C hotplug
[Why and How]
We want to change where timing is done for alt mode.
Some of the commented out #ifs are needed for DCN20
so we enable them for that case.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com> Reviewed-by: Eric Yang <eric.yang2@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
- Need to change interface function signature / add an enum
to reflect the available register field values
[How]
- Add a new enum and modify existing functions to use it instead
of bool
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com> Reviewed-by: Charlene Liu <Charlene.Liu@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amd/display: update optc odm interface for more than 2 opps
Current optc odm interface only accepts 2 opps, we need to
expand this to allow 4 to 1 odm combine.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com> Reviewed-by: Charlene Liu <Charlene.Liu@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Need to add DML struct members that were omitted in previous
DML implemenations.
[How]
- Add missing enum values
- Add missing struct members
- Set new input values in the fetch functions
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com> Reviewed-by: Charlene Liu <Charlene.Liu@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amd/display: Remove duplicate interface for programming FB
[Why]
There are currently two interfaces for exactly the same thing:
hupb_update_dchub in hupb and update_dchub in hubbub. The hubbub
version is currently unused past dcn10, largely because the call
from the dcn10 hardware sequencer does not call through the
interface, so the hupb interface was used instead. This is
confusing because of the duplicate code, the unused functions,
and the fact that more that one block currently owns this set
of registers.
[How]
Remove the hubp interface entirely, as well as the register
declarations that are not longer needed because of this. Change
the call site to always call the hubbub version through the
interface. Fix the update_dchub function in dcn20_hubbub.c to
program the correct registers for dcn20.
Signed-off-by: Julian Parkin <julian.parkin@amd.com> Reviewed-by: Aric Cyr <Aric.Cyr@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Jun Lei [Mon, 22 Jul 2019 13:45:20 +0000 (09:45 -0400)]
drm/amd/display: fix pipe selection logic in validate
[why]
Resource mapping done in dcn20_validate_bandwidth has a flaw: When a full
update is performed, the HWSS will only update the MPCC tree for the stream
that is updated as opposed to all streams. This means that when mapping pipes
in validation, care must be taken to not change any existing mapping, otherwise it
leads to partial hw programming
[how]
it's not strictly necessary to track which stream/mpcc tree is being updated, but
rather it's sufficient to compare current and new state and just keep pipes that were
previously already mapped unchanged.
Signed-off-by: Jun Lei <Jun.Lei@amd.com> Reviewed-by: Eric Yang <eric.yang2@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Nikola Cornij [Wed, 17 Jul 2019 23:02:14 +0000 (19:02 -0400)]
drm/amd/display: Set DSC before DIG front-end is connected to its back-end
[why]
At the time DIG FE is connected to its BE, the clocks in OTG are enabled and
PHY will also be set up. When DSC has to be used to fit the stream into the
available bandwidth, without DSC being set DIG could get exposed to the
higer bandwidth it (or link) could handle. This causes the HW to "reject"
video enable setup (the register shows that video enable was attempted, but
the status bit shows it as disabled).
[how]
- Separate DSC setup into DSC register config and DSC PPS SDP setup
- Move most of the DSC setup (register config) to before
dcn10_link_encoder_connect_dig_be_to_fe() is called
- Set up DSC PPS SDP after DIG FE is connected to its BE. This is because
setting DSC PPS SDP before that has no effect.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com> Reviewed-by: Jun Lei <Jun.Lei@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Nikola Cornij [Thu, 18 Jul 2019 23:13:26 +0000 (19:13 -0400)]
drm/amd/display: Change DSC policy from slices per column to minimum slice height
[why] Minimum slice height is recommended by VESA DSC Spreadsheet user guide
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com> Reviewed-by: Jun Lei <Jun.Lei@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Jun Lei [Thu, 18 Jul 2019 14:02:40 +0000 (10:02 -0400)]
drm/amd/display: clean up DML for DCN2x
[why]
Previous "less risky" implemenation of 3 tiered fallback is no longer necessary since
DMLv2 has gone through proper validation. v2 can now be used as the default and 1
level of fallback can be removed
[how]
remove previous workaround implemenation
Signed-off-by: Jun Lei <Jun.Lei@amd.com> Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Martin Leung [Wed, 17 Jul 2019 20:08:19 +0000 (16:08 -0400)]
drm/amd/display: enabling seamless boot sequence for dcn2
[Why]
Seamless boot (building SW state inheriting BIOS-initialized timing) was
enabled on DCN2, including fixes
[How]
Includes fixes for MPC, DPPCLK, and DIG FE mapping/OTG source select/
Pixel clock.
This is part 2 of 2 for seamless boot NV10
Signed-off-by: Martin Leung <martin.leung@amd.com> Reviewed-by: Jun Lei <Jun.Lei@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
underflow seen on certain monitor setups caused by making dcnxx_init_hw
generic
[How]
by moving dcn20_init_hw into dcn10, we added a dcn-specific clk_mgr
init (dc->clk_mgr->funcs->init_clocks()). Thus, put old clk_mgr
memset in an else statement so both memsets don't get set
Signed-off-by: Martin Leung <martin.leung@amd.com> Reviewed-by: Anthony Koo <Anthony.Koo@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Martin Leung [Tue, 9 Jul 2019 19:15:17 +0000 (15:15 -0400)]
drm/amd/display: Make init_hw and init_pipes generic for seamless boot
[Why]
For seamless boot the init_hw sequence must be split into
actual hardware vs pipes, in order to defer pipe initialization to set mode
and skip of pipe-destructive sequences
[How]
made dcn10_init_hw and dcn10_init_pipes generic for future dcns to inherit
deleted dcn20 specific versions. This is part 1 of a 2 partimplementation
of seamless boot
Signed-off-by: Martin Leung <martin.leung@amd.com> Reviewed-by: Jun Lei <Jun.Lei@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Jun Lei [Tue, 16 Jul 2019 17:02:41 +0000 (13:02 -0400)]
drm/amd/display: wait for pending complete when enabling a plane
[why]
When planes are enabled, they must be enabled using VSYNC update (not immediate).
However, before the VUPDATE occurs, DM may call with an "immediate" flip which is address
only. This operation would normally be okay, but if the locking for immediate flip happens
to occur before the VUPDATE associated with the initial plane enablement, it will cause HW
to hang.
[how]
HWSS should enforce plane enable in HW to be synchronous with the call that enables the plane.
Signed-off-by: Jun Lei <Jun.Lei@amd.com> Reviewed-by: Eric Yang <eric.yang2@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amd/display: refactor gpio to allocate hw_container in constructor
[why]
if dynamic allocation fails during gpio_open, it will cause crash due to
page fault.
[how]
handle allocation when gpio object gets created and prevent from calling
gpio_open if allocation failed
Signed-off-by: Su Sung Chung <Su.Chung@amd.com> Reviewed-by: Jun Lei <Jun.Lei@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amd/display: Add work-around option to skip DCN20 clock updates
[Why] Auto Overclock Memory fails for some systems that don't support
p-state.
[How] Implement the workaround, and it's corresponding enable flag.
Signed-off-by: Jaehyun Chung <jaehyun.chung@amd.com> Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Jun Lei [Mon, 15 Jul 2019 14:41:47 +0000 (10:41 -0400)]
drm/amd/display: fixup DPP programming sequence
[why]
DC does not correct account for the fact that DPP DTO is double buffered while DPP ref is not.
This means that when DPP ref clock is lowered when it's "safe to lower", the DPP blocks that need
an increased divider will temporarily have actual DPP clock drop below minimum while DTO
double buffering takes effect. This results in temporary underflow.
[how]
To fix this, DPP clock cannot be programmed atomically, but rather be broken up into the DTO and the
ref. Each has a separate "safe to lower" logic. When doing "prepare" the ref and dividers may only increase.
When doing "optimize", both may decrease. It is guaranteed that we won't exceed max DPP clock because
we do not use dividers larger than 1.
Signed-off-by: Jun Lei <Jun.Lei@amd.com> Reviewed-by: Eric Yang <eric.yang2@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amd/display: make firmware info only load once during dc_bios create
Currently every time DC wants to access firmware info we make a call
into VBIOS. This makes no sense as there is nothing that can change
runtime inside fw info and can cause issues when calling unstable
bios during bringup.
This change eliminate this behavior by only calling bios once for fw
info and keeping it stored as part of dc_bios.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com> Reviewed-by: Chris Park <Chris.Park@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
David Galiffi [Mon, 24 Jun 2019 14:34:13 +0000 (10:34 -0400)]
drm/amd/display: Synchronous DisplayPort Link Training
[WHY]
We require a method to perform synchronous link training.
[HOW]
Sync LT is broken into 3 basic steps.
"Begin" starts the state machine, and resets "preferred" link settings.
"Attempt" will attempt to train the link with a given set of training
parameters.
"End" stops the state machine, and will optionally disable the link phy.
Between "Begin" and "End" DPCD:600h must not be set to "2"
(D3:Powered Down).
Between "Begin" and "End", there may be multiple "Attempts" with different
training parameters.
Signed-off-by: David Galiffi <david.galiffi@amd.com> Reviewed-by: Jun Lei <Jun.Lei@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amd/display: Improve sharing of HUBBUB register lists
Add DCN20 common register list that contains registers shared
between DCN20 generations.
Signed-off-by: Julian Parkin <julian.parkin@amd.com> Reviewed-by: Charlene Liu <Charlene.Liu@amd.com> Acked-by: Aric Cyr <Aric.Cyr@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Bayan Zabihiyan [Wed, 10 Jul 2019 20:00:53 +0000 (16:00 -0400)]
drm/amd/display: Fix frames_to_insert math
[Why]
The math on deciding on how many
"frames to insert" sometimes sent us over the max refresh rate.
Also integer overflow can occur if we have high refresh rates.
[How]
Instead of clipping the frame duration such that it doesn’t go below the min,
just remove a frame from the number of frames to insert. +
Use unsigned long long for intermediate calculations to prevent
integer overflow.
Signed-off-by: Bayan Zabihiyan <bayan.zabihiyan@amd.com> Reviewed-by: Aric Cyr <Aric.Cyr@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Anthony Koo [Fri, 12 Jul 2019 14:52:54 +0000 (10:52 -0400)]
drm/amd/display: fix issue where 252-255 values are clipped
[Why]
When endpoint is at the boundary of a region, such as at 2^0=1
we find that the last segment has a sharp slope and some points
are clipped at the top.
[How]
If end point is 1, which is exactly at the 2^0 region boundary, we
need to program an additional region beyond this point.
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com> Reviewed-by: Aric Cyr <Aric.Cyr@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Wenjing Liu [Wed, 10 Jul 2019 22:35:18 +0000 (18:35 -0400)]
drm/amd/display: reset hdmi tmds rate and data scramble on pipe reset
[why]
hdmi data scramble and tmds rate is not reset during pipe reset.
[how]
reset hdmi tmds rate and data scramble on pipe reset
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com> Reviewed-by: Chris Park <Chris.Park@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Wenjing Liu [Wed, 10 Jul 2019 22:31:38 +0000 (18:31 -0400)]
drm/amd/display: reset drr programming on pipe reset
[why]
drr is still enabled after driver is unloaded causing black screen
[how]
disable drr during pipe reset.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com> Reviewed-by: Jun Lei <Jun.Lei@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Yongqiang Sun [Tue, 25 Jun 2019 23:08:50 +0000 (19:08 -0400)]
drm/amd/display: Add DFS reference clock field
Add to clk_mgr_internal struct, for future use.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com> Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Yongqiang Sun [Sat, 22 Jun 2019 22:52:41 +0000 (18:52 -0400)]
drm/amd/display: Add PIXEL_RATE control regs for more instances
For use by future ASICs
Signed-off-by: Sung Lee <sung.lee@amd.com> Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com> Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Christian König [Fri, 9 Aug 2019 15:27:21 +0000 (17:27 +0200)]
drm/scheduler: use job count instead of peek
The spsc_queue_peek function is accessing queue->head which belongs to
the consumer thread and shouldn't be accessed by the producer
This is fixing a rare race condition when destroying entities.
Signed-off-by: Christian König <christian.koenig@amd.com> Acked-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com> Reviewed-by: Monk.liu@amd.com Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Kevin Wang [Tue, 13 Aug 2019 08:52:04 +0000 (16:52 +0800)]
drm/amdgpu: use exiting amdgpu_ctx_total_num_entities function
simplify driver code.
Signed-off-by: Kevin Wang <kevin1.wang@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Kevin Wang [Tue, 13 Aug 2019 08:48:28 +0000 (16:48 +0800)]
drm/amdgpu: fix typo error amdgput -> amdgpu
fix typo error:
change function name from "amdgput_ctx_total_num_entities" to
"amdgpu_ctx_total_num_entities".
Signed-off-by: Kevin Wang <kevin1.wang@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Kevin Wang [Tue, 13 Aug 2019 02:25:25 +0000 (10:25 +0800)]
drm/amd/powerplay: fix message of SetHardMinByFreq failed when feature is disabled
the direct send message to smc to set hard clokc will failed
when smc clock dpm feature is disabled.
so use function of smu_set_hard_freq_range to replace it.
the function will check feature enablement.
eg: when uclk (mclk) dpm feature is disabled on navi10
[ 300.675901] amdgpu: [powerplay] failed send message: SetHardMinByFreq(28)
param: 0x00020064 response 0xfffffffb
Signed-off-by: Kevin Wang <kevin1.wang@amd.com> Reviewed-by: Evan Quan <evan.quan@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Chengming Gui [Mon, 12 Aug 2019 02:06:34 +0000 (10:06 +0800)]
drm/amd/powerplay: remove redundancy debug log about smu unsupported features
remove redundancy debug log about smu unsupported features
Signed-off-by: Chengming Gui <Jack.Gui@amd.com> Reviewed-by: Kevin Wang <kevin1.wang@amd.com> Reviewed-by: Evan Quan <evan.quan@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amdgpu: simplify and cleanup setting the dma mask
Use dma_set_mask_and_coherent to set both masks in one go, and remove
the no longer required fallback, as the kernel now always accepts
larger than required DMA masks. Fail the driver probe if we can't
set the DMA mask, as that means the system can only support a larger
mask.
Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/radeon: simplify and cleanup setting the dma mask
Use dma_set_mask_and_coherent to set both masks in one go, and remove
the no longer required fallback, as the kernel now always accepts
larger than required DMA masks. Fail the driver probe if we can't
set the DMA mask, as that means the system can only support a larger
mask.
Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amdgpu: handle PCIe root ports with addressing limitations
amdgpu uses a need_dma32 flag to indicate to the drm core that some
allocations need to be done using GFP_DMA32, but it only checks the
device addressing capabilities to make that decision. Unfortunately
PCIe root ports that have limited addressing exist as well. Use the
dma_addressing_limited instead to also take those into account.
Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/radeon: handle PCIe root ports with addressing limitations
radeon uses a need_dma32 flag to indicate to the drm core that some
allocations need to be done using GFP_DMA32, but it only checks the
device addressing capabilities to make that decision. Unfortunately
PCIe root ports that have limited addressing exist as well. Use the
dma_addressing_limited instead to also take those into account.
Reviewed-by: Christian König <christian.koenig@amd.com> Reported-by: Atish Patra <Atish.Patra@wdc.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Leo Liu [Mon, 15 Jul 2019 13:21:57 +0000 (09:21 -0400)]
drm/amdgpu: add VCN2.0 to Renoir IP blocks
Thus enable VCN2.0 for Renoir
Acked-by: Huang Rui <ray.huang@amd.com> Signed-off-by: Leo Liu <leo.liu@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Leo Liu [Mon, 15 Jul 2019 14:14:17 +0000 (10:14 -0400)]
drm/amdgpu: enable Doorbell support for Renoir (v2)
Add VCN range aperture to NBIO 7.0
v2: rebase (Alex)
Acked-by: Huang Rui <ray.huang@amd.com> Signed-off-by: Leo Liu <leo.liu@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Leo Liu [Mon, 15 Jul 2019 13:01:51 +0000 (09:01 -0400)]
drm/amdgpu: enable Renoir VCN firmware loading
By adding new Renoir VCN firmware
Acked-by: Huang Rui <ray.huang@amd.com> Signed-off-by: Leo Liu <leo.liu@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Aaron Liu [Wed, 24 Jul 2019 18:53:17 +0000 (13:53 -0500)]
drm/amdgpu: fix no interrupt issue for renoir emu
In renoir's ih model, there's a change in mmIH_CHICKEN
register, that limits IH to use physical address directly.
Those chicken bits need to be programmed first.
Acked-by: Huang Rui <ray.huang@amd.com> Signed-off-by: Aaron Liu <aaron.liu@amd.com> Reviewed-by: Huang Rui <ray.huang@amd.com> Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The check on ret is duplicated in two places, it is redundant code.
Remove it.
Addresses-Coverity: ("Logically dead code") Fixes: b94afb61cdae ("drm/amd/powerplay: honor hw limit on fetching metrics data for navi10") Reviewed-by: Evan Quan <evan.quan@amd.com> Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The SOC15_REG_OFFSET() macro wasn't used, making the soft recovery fail.
v2: use WREG32_SOC15 instead of WREG32 + SOC15_REG_OFFSET
Signed-off-by: Pierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Le Ma [Thu, 8 Aug 2019 06:54:12 +0000 (14:54 +0800)]
drm/amdgpu: split athub clock gating from mmhub
Untie the bind of get/set athub CG state from mmhub, for cosmetic fix and Asic
not using mmhub 1.0. Besides, also fix wrong athub CG state in amdgpu_pm_info.
Signed-off-by: Le Ma <le.ma@amd.com> Reviewed-by: Feifei Xu <Feifei.Xu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Michel Dänzer [Wed, 24 Jul 2019 15:56:28 +0000 (17:56 +0200)]
drm/amdgpu: Update pitch on page flips without DC as well
DC already handles this correctly since amdgpu minor version 31. Bump
the minor version again so that xf86-video-amdgpu can take advantage of
this working without DC as well now.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Michel Dänzer <michel.daenzer@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
David Francis [Wed, 7 Aug 2019 14:25:48 +0000 (10:25 -0400)]
drm/amd/display: Remove drm_dsc_dc.c
This file was accidentally added to the driver during
Navi promotion
Nothing includes it. No makefile attempts to compile it, and
it would fail compilation if they tried
Remove it
Signed-off-by: David Francis <David.Francis@amd.com> Reviewed-by: Harry Wentland <harry.wentland@amd.com>w Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
projects / mirror_ubuntu-focal-kernel.git / log