The qdsp6ss memory region is being shared by ADSP remoteproc device and
lpasscc clock device, hence causing memory conflict.
To avoid this, when qdsp6ss clocks are being enabled in remoteproc driver,
skip qdsp6ss clock registration if "qcom,adsp-pil-mode" is enabled and
also assign max_register value.
Fixes: 4ab43d171181 ("clk: qcom: Add lpass clock controller driver for SC7280") Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com> Signed-off-by: Mohammad Rafi Shaik <quic_mohs@quicinc.com> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230407092255.119690-3-quic_mohs@quicinc.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Commit dfe843dce775 ("s390/checksum: support GENERIC_CSUM, enable it for
KASAN") switched s390 to use the generic checksum functions, so that KASAN
instrumentation also works checksum functions by avoiding architecture
specific inline assemblies.
There is however the problem that the generic csum_partial() function
returns a 32 bit value with a 16 bit folded checksum, while the original
s390 variant does not fold to 16 bit. This in turn causes that the
ipib_checksum in lowcore contains different values depending on kernel
config options.
The ipib_checksum is used by system dumpers to verify if pointers in
lowcore point to valid data. Verification is done by comparing checksum
values. The system dumpers still use 32 bit checksum values which are not
folded, and therefore the checksum verification fails (incorrectly).
Symptom is that reboot after dump does not work anymore when a KASAN
instrumented kernel is dumped.
Fix this by not using the generic checksum implementation. Instead add an
explicit kasan_check_read() so that KASAN knows about the read access from
within the inline assembly.
Reported-by: Alexander Egorenkov <egorenar@linux.ibm.com> Fixes: dfe843dce775 ("s390/checksum: support GENERIC_CSUM, enable it for KASAN") Tested-by: Alexander Egorenkov <egorenar@linux.ibm.com> Signed-off-by: Heiko Carstens <hca@linux.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
With the addition of the V2 page table support, the domain page size
bitmap needs to be set prior to iommu core setting up direct mappings
for reserved regions. When reserved regions are mapped, if this is not
done, it will be looking at the V1 page size bitmap when determining
the page size to use in iommu_pgsize(). When it gets into the actual
amd mapping code, a check of see if the page size is supported can
fail, because at that point it is checking it against the V2 page size
bitmap which only supports 4K, 2M, and 1G.
Add a check to __iommu_domain_alloc() to not override the
bitmap if it was already set by the iommu ops domain_alloc() code path.
Cc: Vasant Hegde <vasant.hegde@amd.com> Cc: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com> Cc: Robin Murphy <robin.murphy@arm.com> Cc: Will Deacon <will@kernel.org> Cc: Joerg Roedel <joro@8bytes.org> Fixes: 4db6c41f0946 ("iommu/amd: Add support for using AMD IOMMU v2 page table for DMA-API") Signed-off-by: Jerry Snitselaar <jsnitsel@redhat.com> Reviewed-by: Vasant Hegde <vasant.hegde@amd.com> Link: https://lore.kernel.org/r/20230404072742.1895252-1-jsnitsel@redhat.com Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
XBAR_DIVBUS and AD_SLOW should set parent to XBAR_AD_DIVPLAT and
XBAR_DIVBUS respectively, not the NIC_AD. otherwise we will get
wrong clock rate.
Fixes: c43a801a5789 ("clk: imx: Add clock driver for imx8ulp") Reviewed-by: Jacky Bai <ping.bai@nxp.com> Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Abel Vesa <abel.vesa@linaro.org> Link: https://lore.kernel.org/r/20230331063814.2462059-2-peng.fan@oss.nxp.com Signed-off-by: Abel Vesa <abel.vesa@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When programming PLL, should disable Hardware control select to make PLL
controlled by register, not hardware inputs through OSCPLL.
Fixes: 1b26cb8a77a4 ("clk: imx: support fracn gppll") Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Abel Vesa <abel.vesa@linaro.org> Link: https://lore.kernel.org/r/20230403095300.3386988-3-peng.fan@oss.nxp.com Signed-off-by: Abel Vesa <abel.vesa@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The Fvco should be range 2.4GHz to 5GHz, the original table voilate the
spec, so update the table to fix it.
Fixes: c196175acdd3 ("clk: imx: clk-fracn-gppll: Add more freq config for video pll") Fixes: 044034efbeea ("clk: imx: clk-fracn-gppll: fix mfd value") Fixes: 1b26cb8a77a4 ("clk: imx: support fracn gppll") Signed-off-by: Jacky Bai <ping.bai@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Abel Vesa <abel.vesa@linaro.org> Link: https://lore.kernel.org/r/20230403095300.3386988-2-peng.fan@oss.nxp.com Signed-off-by: Abel Vesa <abel.vesa@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
hfi1 user SDMA request processing has two bugs that can cause data
corruption for user SDMA requests that have multiple payload iovecs
where an iovec other than the tail iovec does not run up to the page
boundary for the buffer pointed to by that iovec.a
Here are the specific bugs:
1. user_sdma_txadd() does not use struct user_sdma_iovec->iov.iov_len.
Rather, user_sdma_txadd() will add up to PAGE_SIZE bytes from iovec
to the packet, even if some of those bytes are past
iovec->iov.iov_len and are thus not intended to be in the packet.
2. user_sdma_txadd() and user_sdma_send_pkts() fail to advance to the
next iovec in user_sdma_request->iovs when the current iovec
is not PAGE_SIZE and does not contain enough data to complete the
packet. The transmitted packet will contain the wrong data from the
iovec pages.
This has not been an issue with SDMA packets from hfi1 Verbs or PSM2
because they only produce iovecs that end short of PAGE_SIZE as the tail
iovec of an SDMA request.
Fixing these bugs exposes other bugs with the SDMA pin cache
(struct mmu_rb_handler) that get in way of supporting user SDMA requests
with multiple payload iovecs whose buffers do not end at PAGE_SIZE. So
this commit fixes those issues as well.
Here are the mmu_rb_handler bugs that non-PAGE_SIZE-end multi-iovec
payload user SDMA requests can hit:
1. Overlapping memory ranges in mmu_rb_handler will result in duplicate
pinnings.
2. When extending an existing mmu_rb_handler entry (struct mmu_rb_node),
the mmu_rb code (1) removes the existing entry under a lock, (2)
releases that lock, pins the new pages, (3) then reacquires the lock
to insert the extended mmu_rb_node.
If someone else comes in and inserts an overlapping entry between (2)
and (3), insert in (3) will fail.
The failure path code in this case unpins _all_ pages in either the
original mmu_rb_node or the new mmu_rb_node that was inserted between
(2) and (3).
3. In hfi1_mmu_rb_remove_unless_exact(), mmu_rb_node->refcount is
incremented outside of mmu_rb_handler->lock. As a result, mmu_rb_node
could be evicted by another thread that gets mmu_rb_handler->lock and
checks mmu_rb_node->refcount before mmu_rb_node->refcount is
incremented.
4. Related to #2 above, SDMA request submission failure path does not
check mmu_rb_node->refcount before freeing mmu_rb_node object.
If there are other SDMA requests in progress whose iovecs have
pointers to the now-freed mmu_rb_node(s), those pointers to the
now-freed mmu_rb nodes will be dereferenced when those SDMA requests
complete.
Fixes: 7be85676f1d1 ("IB/hfi1: Don't remove RB entry when not needed.") Fixes: 7724105686e7 ("IB/hfi1: add driver files") Signed-off-by: Brendan Cunningham <bcunningham@cornelisnetworks.com> Signed-off-by: Patrick Kelsey <pat.kelsey@cornelisnetworks.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com> Link: https://lore.kernel.org/r/168088636445.3027109.10054635277810177889.stgit@252.162.96.66.static.eigbox.net Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
hfi1_mmu_rb_remove_unless_exact() did not move mmu_rb_node objects in
mmu_rb_handler->lru_list after getting a cache hit on an mmu_rb_node.
As a result, hfi1_mmu_rb_evict() was not guaranteed to evict truly
least-recently used nodes.
This could be a performance issue for an application when that
application:
- Uses some long-lived buffers frequently.
- Uses a large number of buffers once.
- Hits the mmu_rb_handler cache size or pinned-page limits, forcing
mmu_rb_handler cache entries to be evicted.
In this case, the one-time use buffers cause the long-lived buffer
entries to eventually filter to the end of the LRU list where
hfi1_mmu_rb_evict() will consider evicting a frequently-used long-lived
entry instead of evicting one of the one-time use entries.
Fix this by inserting new mmu_rb_node at the tail of
mmu_rb_handler->lru_list and move mmu_rb_ndoe to the tail of
mmu_rb_handler->lru_list when the mmu_rb_node is a hit in
hfi1_mmu_rb_remove_unless_exact(). Change hfi1_mmu_rb_evict() to evict
from the head of mmu_rb_handler->lru_list instead of the tail.
Fixes: 0636e9ab8355 ("IB/hfi1: Add cache evict LRU list") Signed-off-by: Brendan Cunningham <bcunningham@cornelisnetworks.com> Signed-off-by: Patrick Kelsey <pat.kelsey@cornelisnetworks.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com> Link: https://lore.kernel.org/r/168088635931.3027109.10423156330761536044.stgit@252.162.96.66.static.eigbox.net Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When unregistering MAD agent, srpt module has a non-null check
for 'mad_agent' pointer before invoking ib_unregister_mad_agent().
This check can pass if 'mad_agent' variable holds an error value.
The 'mad_agent' can have an error value for a short window when
srpt_add_one() and srpt_remove_one() is executed simultaneously.
In srpt module, added a valid pointer check for 'sport->mad_agent'
before unregistering MAD agent.
This issue can hit when RoCE driver unregisters ib_device
Trace icm_send_rej event before the cm state is reset to idle, so that
correct cm state will be logged. For example when an incoming request is
rejected, the old trace log was:
icm_send_rej: local_id=961102742 remote_id=3829151631 state=IDLE reason=REJ_CONSUMER_DEFINED
With this patch:
icm_send_rej: local_id=312971016 remote_id=3778819983 state=MRA_REQ_SENT reason=REJ_CONSUMER_DEFINED
Fixes: 8dc105befe16 ("RDMA/cm: Add tracepoints to track MAD send operations") Signed-off-by: Mark Zhang <markzhang@nvidia.com> Link: https://lore.kernel.org/r/20230330072351.481200-1-markzhang@nvidia.com Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When the SOC approaches zero, an integer overflows in the columb
counter causing the driver to react poorly. This makes the driver
think it's at (above) the fully charged capacity when in fact it's
zero. It would then write this full capacity to NVRAM which would be
used on boot if the device remained off for less than 5 hours and
not plugged in.
This can be fixed and guarded against by doing the following:
- Changing the type of tmp in rk817_read_or_set_full_charge_on_boot()
to be an int instead of a u32. That way we can account for negative
numbers.
- Guard against negative values for the full charge on boot by setting
the charge to 0 if the system charge reports less than 0.
- Catch scenarios where the battery voltage is below the design
minimum voltage and set the system SOC to 0 at that time and update
the columb counter with a charge level of 0.
- Change the off time value from 5 hours to 30 minutes before we
recalculate the current capacity based on the OCV tables.
These changes allow the driver to operate better at low voltage/low
capacity conditions.
Fixes: 3268a4d9b0b8 ("power: supply: rk817: Fix unsigned comparison with less than zero") Fixes: 11cb8da0189b ("power: supply: Add charger driver for Rockchip RK817") Signed-off-by: Chris Morgan <macromorgan@hotmail.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
syzbot is reporting that siw_netdev_event(NETDEV_UNREGISTER) cannot destroy
siw_device created after unshare(CLONE_NEWNET) due to net namespace check.
It seems that this check was by error there and should be removed.
Reported-by: syzbot <syzbot+5e70d01ee8985ae62a3b@syzkaller.appspotmail.com> Link: https://syzkaller.appspot.com/bug?extid=5e70d01ee8985ae62a3b Suggested-by: Jason Gunthorpe <jgg@ziepe.ca> Suggested-by: Leon Romanovsky <leon@kernel.org> Fixes: bdcf26bf9b3a ("rdma/siw: network and RDMA core interface") Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Link: https://lore.kernel.org/r/a44e9ac5-44e2-d575-9e30-02483cc7ffd1@I-love.SAKURA.ne.jp Reviewed-by: Bernard Metzler <bmt@zurich.ibm.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When returning from of_parse_phandle_with_args(), the np member of the
of_phandle_args structure should be put after usage. Add missing
of_node_put() calls in both __set_clk_parents() and __set_clk_rates().
Fixes: 86be408bfbd8 ("clk: Support for clock parents and rates assigned from device tree") Signed-off-by: Clément Léger <clement.leger@bootlin.com> Link: https://lore.kernel.org/r/20230131083227.10990-1-clement.leger@bootlin.com Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Remove the tasklet call in rxe_cq.c and also the is_dying in the
cq struct. There is no reason for the rxe driver to defer the call
to the cq completion handler by scheduling a tasklet. rxe_cq_post()
is not called in a hard irq context.
The rxe driver currently is incorrect because the tasklet call is
made without protecting the cq pointer with a reference from having
the underlying memory freed before the deferred routine is called.
Executing the comp_handler inline fixes this problem.
Fixes: 8700e3e7c485 ("Soft RoCE driver") Signed-off-by: Bob Pearson <rpearsonhpe@gmail.com> Link: https://lore.kernel.org/r/20230327215643.10410-1-rpearsonhpe@gmail.com Acked-by: Zhu Yanjun <zyjzyj2000@gmail.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
BUG: KASAN: slab-out-of-bounds in hdr_delete_de+0xe0/0x150 fs/ntfs3/index.c:806
Read of size 16842960 at addr ffff888079cc0600 by task syz-executor934/3631
Before using the meta-data in struct INDEX_HDR, we need to
check index header valid or not. Otherwise, the corruptedi
(or malicious) fs image can cause out-of-bounds access which
could make kernel panic.
Fixes: 82cae269cfa9 ("fs/ntfs3: Add initialization of super block") Reported-by: syzbot+9c2811fd56591639ff5f@syzkaller.appspotmail.com Signed-off-by: Zeng Heng <zengheng4@huawei.com> Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
BUG: KASAN: slab-out-of-bounds in indx_insert_into_buffer+0xaa3/0x13b0
fs/ntfs3/index.c:1755
Read of size 17168 at addr ffff8880255e06c0 by task syz-executor308/3630
If the member struct INDEX_BUFFER *index of struct indx_node is
incorrect, that is, the value of __le32 used is greater than the value
of __le32 total in struct INDEX_HDR. Therefore, OOB read occurs when
memmove is called in indx_insert_into_buffer().
Fix this by adding a check in hdr_find_e().
Fixes: 82cae269cfa9 ("fs/ntfs3: Add initialization of super block") Reported-by: syzbot+d882d57193079e379309@syzkaller.appspotmail.com Signed-off-by: ZhangPeng <zhangpeng362@huawei.com> Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Label ATTR_ROOT in ntfs_read_mft() sets is_root = true and
ni->ni_flags |= NI_FLAG_DIR, then next attr will goto label ATTR_ALLOC
and alloc ni->dir.alloc_run. However two states are not always
consistent and can make memory leak.
1) attr_name in ATTR_ROOT does not fit the condition it will set
is_root = true but NI_FLAG_DIR is not set.
2) next attr_name in ATTR_ALLOC fits the condition and alloc
ni->dir.alloc_run
3) in cleanup function ni_clear(), when NI_FLAG_DIR is set, it frees
ni->dir.alloc_run, otherwise it frees ni->file.run
4) because NI_FLAG_DIR is not set in this case, ni->dir.alloc_run is
leaked as kmemleak reported:
'exists' looks like a boolean. This patch replaces it by the
normal name used for the rxe device, 'rxe', which should be a
little less confusing. The second rxe_dbg() message is
incorrect since rxe is known to be NULL and this will cause a
seg fault if this message were ever sent. Replace it by pr_debug
for the moment.
Fixes: c6aba5ea0055 ("RDMA/rxe: Replace pr_xxx by rxe_dbg_xxx in rxe.c") Link: https://lore.kernel.org/r/20230303221623.8053-2-rpearsonhpe@gmail.com Signed-off-by: Bob Pearson <rpearsonhpe@gmail.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The VRTC alarm register can be programmed with an amount of seconds
after which the SoC will be woken up by the VRTC timer again. We are
already converting the alarm time from meson_vrtc_set_alarm() to
"seconds since 1970". This means we also need to use "seconds since
1970" for the current time.
This fixes a problem where setting the alarm to one minute in the future
results in the firmware (which handles wakeup) to output (on the serial
console) that the system will be woken up in billions of seconds.
ktime_get_raw_ts64() returns the time since boot, not since 1970. Switch
to ktime_get_real_ts64() to fix the calculation of the alarm time and to
make the SoC wake up at the specified date/time. Also the firmware
(which manages suspend) now prints either 59 or 60 seconds until wakeup
(depending on how long it takes for the system to enter suspend).
Fixes: 6ef35398e827 ("rtc: Add Amlogic Virtual Wake RTC") Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> Reviewed-by: Kevin Hilman <khilman@baylibre.com> Link: https://lore.kernel.org/r/20230320212142.2355062-1-martin.blumenstingl@googlemail.com Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The ucmd->log_sq_bb_count variable is controlled by the user so this
shift can wrap. Fix it by using check_shl_overflow() in the same way
that it was done in commit 515f60004ed9 ("RDMA/hns: Prevent undefined
behavior in hns_roce_set_user_sq_size()").
Fixes: 839041329fd3 ("IB/mlx4: Sanity check userspace send queue sizes") Signed-off-by: Dan Carpenter <error27@gmail.com> Link: https://lore.kernel.org/r/a8dfbd1d-c019-4556-930b-bab1ded73b10@kili.mountain Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The workqueue watchdog prints a warning when there is no progress in
a worker pool. Where the progress means that the pool started processing
a pending work item.
Note that it is perfectly fine to process work items much longer.
The progress should be guaranteed by waking up or creating idle
workers.
show_one_worker_pool() prints state of non-idle worker pool. It shows
a delay since the last pool->watchdog_ts.
The timestamp is updated when a first pending work is queued in
__queue_work(). Also it is updated when a work is dequeued for
processing in worker_thread() and rescuer_thread().
The delay is misleading when there is no pending work item. In this
case it shows how long the last work item is being proceed. Show
zero instead. There is no stall if there is no pending work.
Fixes: 82607adcf9cdf40fb7b ("workqueue: implement lockup detector") Signed-off-by: Petr Mladek <pmladek@suse.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The device_node pointer returned by of_find_compatible_node() with
refcount incremented, when finish using it, the refcount need be
decreased.
Fixes: d7964de8a8ea ("clk: mediatek: Add new clock driver to handle FHCTL hardware") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Link: https://lore.kernel.org/r/20221229092946.4162345-1-yangyingliang@huawei.com
[sboyd@kernel.org: Also unmap on error] Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
There is no need to check 'rdi->qp_dev' for NULL. The field 'qp_dev'
is created in rvt_register_device() which will fail if the 'qp_dev'
allocation fails in rvt_driver_qp_init(). Overwise this pointer
doesn't changed and passed to rvt_qp_exit() by the next step.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 0acb0cc7ecc1 ("IB/rdmavt: Initialize and teardown of qpn table") Signed-off-by: Natalia Petrova <n.petrova@fintech.ru> Link: https://lore.kernel.org/r/20230303124408.16685-1-n.petrova@fintech.ru Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
All the various MediaTek clock drivers are, in a way or another,
redefining the GATE_MTK() macro with different names: while some
are doing that by actually using GATE_MTK(), others are copying
it entirely (hence, entirely redefining it).
Change all clock drivers to always and consistently use this macro.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Reviewed-by: Chen-Yu Tsai <wenst@chromium.org> Tested-by: Chen-Yu Tsai <wenst@chromium.org> # MT8183, MT8192, MT8195 Chromebooks Link: https://lore.kernel.org/r/20230306140543.1813621-23-angelogioacchino.delregno@collabora.com Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Stable-dep-of: fa8c0d01df62 ("clk: mediatek: mt7622: Properly use CLK_IS_CRITICAL flag") Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The write index indicates which event the data is for and accesses a
per-file array. The index is passed by user processes during write()
calls as the first 4 bytes. Ensure that it cannot be negative by
returning -EINVAL to prevent out of bounds accesses.
Update ftrace self-test to ensure this occurs properly.
Link: https://lkml.kernel.org/r/20230425225107.8525-2-beaub@linux.microsoft.com Fixes: 7f5a08c79df3 ("user_events: Add minimal support for trace_event into ftrace") Reported-by: Doug Cook <dcook@linux.microsoft.com> Signed-off-by: Beau Belgrave <beaub@linux.microsoft.com> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The variable run is not initialized however it is being accumulated
by the return value from the call to ikm_run_monitor. Fix this by
initializing run to zero at the start of the function.
Link: https://lkml.kernel.org/r/20230424094730.105313-1-colin.i.king@gmail.com Fixes: 4bc4b131d44c ("rv: Add rv tool") Signed-off-by: Colin Ian King <colin.i.king@gmail.com> Acked-by: Daniel Bristot de Oliveira <bristot@kernel.org> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Commit 95158a89dd50 ("sched,rt: Use the full cpumask for balancing")
allows find_lock_lowest_rq() to pick a task with migration disabled.
The purpose of the commit is to push the current running task on the
CPU that has the migrate_disable() task away.
However, there is a race which allows a migrate_disable() task to be
migrated. Consider:
The KASAN shadow region was moved next to the kernel mapping but the
ptdump code was not updated and it appears to break the dump of the kernel
page table, so fix this by moving the KASAN shadow region in ptdump.
Fixes: f7ae02333d13 ("riscv: Move KASAN mapping next to the kernel mapping") Signed-off-by: Alexandre Ghiti <alexghiti@rivosinc.com> Tested-by: Björn Töpel <bjorn@rivosinc.com> Reviewed-by: Björn Töpel <bjorn@rivosinc.com> Link: https://lore.kernel.org/r/20230203075232.274282-6-alexghiti@rivosinc.com Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Commit 468af56a7bba ("objtool: Support addition to set CFA base") was
added as a preparatory patch for arm64 support, but that support never
came. It triggers a false positive warning on x86, so just revert it
for now.
Fixes the following warning:
vmlinux.o: warning: objtool: cdce925_regmap_i2c_write+0xdb: stack state mismatch: cfa1=4+120 cfa2=5+40
Fixes: 468af56a7bba ("objtool: Support addition to set CFA base") Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lore.kernel.org/oe-kbuild-all/202304080538.j5G6h1AB-lkp@intel.com/ Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
commit e050e3f0a71bf ("perf: Fix broken interrupt rate throttling")
introduces a change in throttling threshold judgment. Before this,
compare hwc->interrupts and max_samples_per_tick, then increase
hwc->interrupts by 1, but this commit reverses order of these two
behaviors, causing the semantics of max_samples_per_tick to change.
In literal sense of "max_samples_per_tick", if hwc->interrupts ==
max_samples_per_tick, it should not be throttled, therefore, the judgment
condition should be changed to "hwc->interrupts > max_samples_per_tick".
In fact, this may cause the hardlockup to fail, The minimum value of
max_samples_per_tick may be 1, in this case, the return value of
__perf_event_account_interrupt function is 1.
As a result, nmi_watchdog gets throttled, which would stop PMU (Use x86
architecture as an example, see x86_pmu_handle_irq).
Fixes: e050e3f0a71b ("perf: Fix broken interrupt rate throttling") Signed-off-by: Yang Jihong <yangjihong1@huawei.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lkml.kernel.org/r/20230227023508.102230-1-yangjihong1@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
There are scenarios where non-affine wakeups are incorrectly counted as
affine wakeups by schedstats.
When wake_affine_idle() returns prev_cpu which doesn't equal to
nr_cpumask_bits, it will slip through the check: target == nr_cpumask_bits
in wake_affine() and be counted as if target == this_cpu in schedstats.
Replace target == nr_cpumask_bits with target != this_cpu to make sure
affine wakeups are accurately tallied.
Fixes: 806486c377e33 (sched/fair: Do not migrate if the prev_cpu is idle) Suggested-by: Daniel Jordan <daniel.m.jordan@oracle.com> Signed-off-by: Libo Chen <libo.chen@oracle.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com> Link: https://lore.kernel.org/r/20220810223313.386614-1-libo.chen@oracle.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Using memcpy() isn't safe when buf is identical to rtas_err_buf, which
can happen during boot before slab is up. Full context which may not
be obvious from the diff:
if (altbuf) {
buf = altbuf;
} else {
buf = rtas_err_buf;
if (slab_is_available())
buf = kmalloc(RTAS_ERROR_LOG_MAX, GFP_ATOMIC);
}
if (buf)
memcpy(buf, rtas_err_buf, RTAS_ERROR_LOG_MAX);
This was found by inspection and I'm not aware of it causing problems
in practice. It appears to have been introduced by commit 033ef338b6e0 ("powerpc: Merge rtas.c into arch/powerpc/kernel"); the
old ppc64 version of this code did not have this problem.
Use memmove() instead.
Fixes: 033ef338b6e0 ("powerpc: Merge rtas.c into arch/powerpc/kernel") Signed-off-by: Nathan Lynch <nathanl@linux.ibm.com> Reviewed-by: Andrew Donnellan <ajd@linux.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://msgid.link/20230220-rtas-queue-for-6-4-v1-2-010e4416f13f@linux.ibm.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
LEDS_TRIGGER_DISK depends on ATA, so selecting LEDS_TRIGGER_DISK
when ATA is not set/enabled causes a Kconfig warning:
WARNING: unmet direct dependencies detected for LEDS_TRIGGER_DISK
Depends on [n]: NEW_LEDS [=y] && LEDS_TRIGGERS [=y] && ATA [=n]
Selected by [y]:
- ADB_PMU_LED_DISK [=y] && MACINTOSH_DRIVERS [=y] && ADB_PMU_LED [=y] && LEDS_CLASS [=y]
Fix this by making ADB_PMU_LED_DISK depend on ATA.
Seen on both PPC32 and PPC64.
Fixes: 0e865a80c135 ("macintosh: Remove dependency on IDE_GD_ATA if ADB_PMU_LED_DISK is selected") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://msgid.link/20230223014241.20878-1-rdunlap@infradead.org Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Use "%pa" format specifier for resource_size_t to avoid a compiler
printk format warning.
arch/powerpc/sysdev/tsi108_pci.c: In function 'tsi108_setup_pci':
include/linux/kern_levels.h:5:25: error: format '%x' expects argument of type 'unsigned int', but argument 2 has type 'resource_size_t'
Fixes: c4342ff92bed ("[POWERPC] Update mpc7448hpc2 board irq support using device tree") Fixes: 2b9d7467a6db ("[POWERPC] Add tsi108 pci and platform device data register function") Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
[mpe: Use pr_info() and unsplit string] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://msgid.link/20230223070116.660-5-rdunlap@infradead.org Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Use "%pa" format specifier for resource_size_t to avoid compiler
printk format warnings.
../arch/powerpc/platforms/embedded6xx/flipper-pic.c: In function 'flipper_pic_init':
../include/linux/kern_levels.h:5:25: error: format '%x' expects argument of type 'unsigned int', but argument 2 has type 'resource_size_t' {aka 'long long unsigned int'} [-Werror=format=]
../arch/powerpc/platforms/embedded6xx/flipper-pic.c:148:9: note: in expansion of macro 'pr_info'
148 | pr_info("controller at 0x%08x mapped to 0x%p\n", res.start, io_base);
| ^~~~~~~
../arch/powerpc/platforms/embedded6xx/hlwd-pic.c: In function 'hlwd_pic_init':
../include/linux/kern_levels.h:5:25: error: format '%x' expects argument of type 'unsigned int', but argument 2 has type 'resource_size_t' {aka 'long long unsigned int'} [-Werror=format=]
../arch/powerpc/platforms/embedded6xx/hlwd-pic.c:174:9: note: in expansion of macro 'pr_info'
174 | pr_info("controller at 0x%08x mapped to 0x%p\n", res.start, io_base);
| ^~~~~~~
../arch/powerpc/platforms/embedded6xx/wii.c: In function 'wii_ioremap_hw_regs':
../include/linux/kern_levels.h:5:25: error: format '%x' expects argument of type 'unsigned int', but argument 3 has type 'resource_size_t' {aka 'long long unsigned int'} [-Werror=format=]
../arch/powerpc/platforms/embedded6xx/wii.c:77:17: note: in expansion of macro 'pr_info'
77 | pr_info("%s at 0x%08x mapped to 0x%p\n", name,
| ^~~~~~~
Fixes: 028ee972f032 ("powerpc: gamecube/wii: flipper interrupt controller support") Fixes: 9c21025c7845 ("powerpc: wii: hollywood interrupt controller support") Fixes: 5a7ee3198dfa ("powerpc: wii: platform support") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://msgid.link/20230223070116.660-3-rdunlap@infradead.org Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Use "%pa" format specifier for resource_size_t to avoid a compiler
printk format warning.
../arch/powerpc/platforms/512x/clock-commonclk.c: In function 'mpc5121_clk_provide_backwards_compat':
../arch/powerpc/platforms/512x/clock-commonclk.c:989:44: error: format '%x' expects argument of type 'unsigned int', but argument 4 has type 'resource_size_t' {aka 'long long unsigned int'} [-Werror=format=]
989 | snprintf(devname, sizeof(devname), "%08x.%s", res.start, np->name); \
| ^~~~~~~~~ ~~~~~~~~~
| |
| resource_size_t {aka long long unsigned int}
Prevents 24 such warnings.
Fixes: 01f25c371658 ("clk: mpc512x: add backwards compat to the CCF code") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://msgid.link/20230223070116.660-2-rdunlap@infradead.org Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Unlike PVR_POWER8, etc ...., PVR_7450 represents a full PVR
value and not a family value.
To avoid confusion, do like E500 family and define the relevant
PVR_VER_xxxx values for the 7450 family:
0x8000 ==> 7450
0x8001 ==> 7455
0x8002 ==> 7447
0x8003 ==> 7447A
0x8004 ==> 7448
And use them to detect 7450 family for perf events.
The testcase verifies the setting of different fields in Monitor Mode
Control Register A (MMCRA). In the current code, EV_CODE_EXTRACT macro
is used to extract the "sample" field, which then needs to be further
processed to fetch rand_samp_elig and rand_samp_mode bits. But the
current code is not passing valid sample field to EV_CODE_EXTRACT
macro. Patch addresses this by fixing the input for EV_CODE_EXTRACT.
When dev_err_probe() is called, 'ret' holds the value of the previous
successful devm_request_irq() call.
'ret' should be assigned with a meaningful value before being used in
dev_err_probe().
While at it, use and return "PTR_ERR(ctrl->clk)" instead of a hard-coded
"-ENOENT" so that -EPROBE_DEFER is handled and propagated correctly.
Fixes: 81b63420564d ("fbdev: mmp: Make use of the helper function dev_err_probe()") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: Helge Deller <deller@gmx.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
In virtio_net, if we disable napi_tx, when we trigger a tx interrupt,
the vq->event_triggered will be set to true. It is then never reset
until we explicitly call virtqueue_enable_cb_delayed or
virtqueue_enable_cb_prepare.
If we disable the napi_tx, virtqueue_enable_cb* will only be called when
the tx ring is getting relatively empty.
Since event_triggered is true, VRING_AVAIL_F_NO_INTERRUPT or
VRING_PACKED_EVENT_FLAG_DISABLE will not be set. As a result we update
vring_used_event(&vq->split.vring) or vq->packed.vring.driver->off_wrap
every time we call virtqueue_get_buf_ctx. This causes more interrupts.
To summarize:
1) event_triggered was set to true in vring_interrupt()
2) after this nothing will happen in virtqueue_disable_cb() so
VRING_AVAIL_F_NO_INTERRUPT is not set in avail_flags_shadow
3) virtqueue_get_buf_ctx_split() will still think the cb is enabled
and then it will publish a new event index
To fix:
update VRING_AVAIL_F_NO_INTERRUPT or VRING_PACKED_EVENT_FLAG_DISABLE in
the vq when we call virtqueue_disable_cb even when event_triggered is
true.
Tested with iperf:
iperf3 tcp stream:
vm1 -----------------> vm2
vm2 just receives tcp data stream from vm1, and sends acks to vm1,
there are many tx interrupts in vm2.
with the patch applied there are just a few tx interrupts.
v2->v3:
-update the interrupt disable flag even with the event_triggered is set,
-instead of checking whether event_triggered is set in
-virtqueue_get_buf_ctx_{packed/split}, will cause the drivers which have
-not called virtqueue_{enable/disable}_cb to miss notifications.
v3->v4:
-remove change for
-"if (vq->packed.event_flags_shadow != VRING_PACKED_EVENT_FLAG_DISABLE)"
-in virtqueue_disable_cb_packed
Fixes: 8d622d21d248 ("virtio: fix up virtio_disable_cb") Signed-off-by: Albert Huang <huangjie.albert@bytedance.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20230329102300.61000-1-huangjie.albert@bytedance.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When removing a SPMI driver, there can be a crash due to NULL pointer
dereference if it does not have a remove callback defined. This is
one such call trace observed when removing the QCOM SPMI PMIC driver:
If a driver has all its resources allocated through devm_() APIs and
does not need any other explicit cleanup, it would not require a
remove callback to be defined. Hence, add a check for remove callback
presence before calling it when removing a SPMI driver.
Link: https://lore.kernel.org/r/1671601032-18397-2-git-send-email-quic_jprakash@quicinc.com Fixes: 6f00f8c8635f ("mfd: qcom-spmi-pmic: Use devm_of_platform_populate()") Fixes: 5a86bf343976 ("spmi: Linux driver framework for SPMI") Signed-off-by: Jishnu Prakash <quic_jprakash@quicinc.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Link: https://lore.kernel.org/r/20230413223834.4084793-7-sboyd@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When loading the driver for rtl8192e, the W_DISABLE# switch is working as
intended. But when the WLAN is turned off in software and then turned on
again the W_DISABLE# does not work anymore. Reason for this is that in
the function _rtl92e_dm_check_rf_ctrl_gpio() the bfirst_after_down is
checked and returned when true. bfirst_after_down is set true when
switching the WLAN off in software. But it is not set to false again
when WLAN is turned on again.
Add bfirst_after_down = false in _rtl92e_sta_up to reset bit and fix
above described bug.
Fixes: 94a799425eee ("From: wlanfae <wlanfae@realtek.com> [PATCH 1/8] rtl8192e: Import new version of driver from realtek") Signed-off-by: Philipp Hortmann <philipp.g.hortmann@gmail.com> Link: https://lore.kernel.org/r/20230418200201.GA17398@matrix-ESPRIMO-P710 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Also get rid of conditional compilation based on CONFIG_PM_SLEEP because
it introduces build issues with certain configs when CQSPI_DEV_PM_OPS is
just NULL.
An 8250 UART configured as a wake-up source would not have reported
itself through sysfs as being the source of wake-up, correct that.
Fixes: b3b708fa2780 ("wake up from a serial port") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Link: https://lore.kernel.org/r/20230414170241.2016255-1-f.fainelli@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When handle qmu transfer irq, it will unlock @mtu->lock before give back
request, if another thread handle disconnect event at the same time, and
try to disable ep, it may lock @mtu->lock and free qmu ring, then qmu
irq hanlder may get a NULL gpd, avoid the KE by checking gpd's value before
handling it.
e.g.
qmu done irq on cpu0 thread running on cpu1
qmu_done_tx()
handle gpd [0]
mtu3_requ_complete() mtu3_gadget_ep_disable()
unlock @mtu->lock
give back request lock @mtu->lock
mtu3_ep_disable()
mtu3_gpd_ring_free()
unlock @mtu->lock
lock @mtu->lock
get next gpd [1]
[1]: goto [0] to handle next gpd, and next gpd may be NULL.
Fixes: 48e0d3735aa5 ("usb: mtu3: supports new QMU format") Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> Link: https://lore.kernel.org/r/20230417025203.18097-3-chunfeng.yun@mediatek.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Commit ac82b56bda5f ("usb: gadget: tegra-xudc: Add vbus_draw support")
populated the vbus_draw callback for the Tegra XUDC driver. The function
tegra_xudc_gadget_vbus_draw(), that was added by this commit, assumes
that the pointer 'curr_usbphy' has been initialised, which is not always
the case because this is only initialised when the USB role is updated.
Fix this crash, by checking that the 'curr_usbphy' is valid before
dereferencing.
The Store Queue code allocates a bitmap buffer with the size of
multiple of sizeof(long) in sq_api_init(). While the buffer size
is calculated correctly, the code uses the wrong element size to
allocate the buffer which results in the allocated bitmap buffer
being too small.
Fix this by allocating the buffer with kcalloc() with element size
sizeof(long) instead of kzalloc() whose elements size defaults to
sizeof(char).
Fixes: d7c30c682a27 ("sh: Store Queue API rework.") Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de> Link: https://lore.kernel.org/r/20230419114854.528677-1-glaubitz@physik.fu-berlin.de Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
typeof is (still) a GNU extension, which means that it cannot be used when
building ISO C (e.g. -std=c99). It should therefore be avoided in uapi
headers in favour of the ISO-friendly __typeof__.
Unfortunately this issue could not be detected by
CONFIG_UAPI_HEADER_TEST=y as the __ALIGN_KERNEL() macro is not expanded in
any uapi header.
This matters from a userspace perspective, not a kernel one. uapi
headers and their contents are expected to be usable in a variety of
situations, and in particular when building ISO C applications (with
-std=c99 or similar).
This particular problem can be reproduced by trying to use the
__ALIGN_KERNEL macro directly in application code, say:
#include <linux/const.h>
int align(int x, int a)
{
return __KERNEL_ALIGN(x, a);
}
and trying to build that with -std=c99.
Link: https://lkml.kernel.org/r/20230411092747.3759032-1-kevin.brodsky@arm.com Fixes: a79ff731a1b2 ("netfilter: xtables: make XT_ALIGN() usable in exported headers by exporting __ALIGN_KERNEL()") Signed-off-by: Kevin Brodsky <kevin.brodsky@arm.com> Reported-by: Ruben Ayrapetyan <ruben.ayrapetyan@arm.com> Tested-by: Ruben Ayrapetyan <ruben.ayrapetyan@arm.com> Reviewed-by: Petr Vorel <pvorel@suse.cz> Tested-by: Petr Vorel <pvorel@suse.cz> Reviewed-by: Masahiro Yamada <masahiroy@kernel.org> Cc: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
If CONFIG_DEBUG_INFO_REDUCED is enabled in the kernel configuration, we
will typically not be able to load vmlinux-gdb.py and will fail with:
Traceback (most recent call last):
File "/home/fainelli/work/buildroot/output/arm64/build/linux-custom/vmlinux-gdb.py", line 25, in <module>
import linux.utils
File "/home/fainelli/work/buildroot/output/arm64/build/linux-custom/scripts/gdb/linux/utils.py", line 131, in <module>
atomic_long_counter_offset = atomic_long_type.get_type()['counter'].bitpos
KeyError: 'counter'
Rather be left wondering what is happening only to find out that reduced
debug information is the cause, raise an eror. This was not typically a
problem until e3c8d33e0d62 ("scripts/gdb: fix 'lx-dmesg' on 32 bits arch")
but it has since then.
Link: https://lkml.kernel.org/r/20230406215252.1580538-1-f.fainelli@gmail.com Fixes: e3c8d33e0d62 ("scripts/gdb: fix 'lx-dmesg' on 32 bits arch") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Cc: Antonio Borneo <antonio.borneo@foss.st.com> Cc: Jan Kiszka <jan.kiszka@siemens.com> Cc: John Ogness <john.ogness@linutronix.de> Cc: Kieran Bingham <kbingham@kernel.org> Cc: Petr Mladek <pmladek@suse.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The xiic_xfer() function gets a runtime PM reference when the function is
entered. This reference is released when the function is exited. There is
currently one error path where the function exits directly, which leads to
a leak of the runtime PM reference.
Make sure that this error path also releases the runtime PM reference.
Fixes: fdacc3c7405d ("i2c: xiic: Switch from waitqueue to completion") Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Reviewed-by: Michal Simek <michal.simek@amd.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The cdns_i2c_master_xfer() function gets a runtime PM reference when the
function is entered. This reference is released when the function is
exited. There is currently one error path where the function exits
directly, which leads to a leak of the runtime PM reference.
Make sure that this error path also releases the runtime PM reference.
Fixes: 1a351b10b967 ("i2c: cadence: Added slave support") Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Reviewed-by: Michal Simek <michal.simek@amd.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The cadence QSPI driver misbehaves after performing a full system suspend
resume:
...
spi-nor spi0.0: resume() failed
...
This results in a flash connected via OSPI interface after system suspend-
resume to be unusable.
fix these suspend and resume functions.
Fixes: 140623410536 ("mtd: spi-nor: Add driver for Cadence Quad SPI Flash Controller") Signed-off-by: Dhruva Gole <d-gole@ti.com> Link: https://lore.kernel.org/r/20230417091027.966146-3-d-gole@ti.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Commit 5dd45b66742a ("drm/panel: novatek-nt35950: Improve error handling")
introduced logic to unregister DSI1 on any sort of probe failure, as
that's not done automatically by kernel APIs.
It did not however account for cases where only one DSI host is used.
Fix that.
Fixes: 5dd45b66742a ("drm/panel: novatek-nt35950: Improve error handling") Reported-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20230417-topic-maple_panel_fixup-v1-1-07c8db606f5e@linaro.org Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Assignment of NVIDIA Ampere-based GPUs have seen a regression since the
below referenced commit, where the reduced D3hot transition delay appears
to introduce a small window where a D3hot->D0 transition followed by a bus
reset can wedge the device. The entire device is subsequently unavailable,
returning -1 on config space read and is unrecoverable without a host
reset.
This has been observed with RTX A2000 and A5000 GPU and audio functions
assigned to a Windows VM, where shutdown of the VM places the devices in
D3hot prior to vfio-pci performing a bus reset when userspace releases the
devices. The issue has roughly a 2-3% chance of occurring per shutdown.
Restoring the HDA controller d3hot_delay to the effective value before the
below commit has been shown to resolve the issue. NVIDIA confirms this
change should be safe for all of their HDA controllers.
of_node_put() should have been done directly after
mqs_priv->regmap = syscon_node_to_regmap(gpr_np);
otherwise it creates a reference leak on the success path.
To fix this, of_node_put() is moved to the correct location, and change
all the gotos to direct returns.
Fixes: a9d273671440 ("ASoC: fsl_mqs: Fix error handling in probe") Signed-off-by: Liliang Ye <yll@hust.edu.cn> Reviewed-by: Dan Carpenter <error27@gmail.com> Link: https://lore.kernel.org/r/20230403152647.17638-1-yll@hust.edu.cn Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
In a very peculiar case when probing and registering with the secondary
DSI host succeeds, but the OF backlight or DSI attachment fails, the
primary DSI device is automatically cleaned up, but the secondary one
is not, leading to -EEXIST when the driver core tries to handle
-EPROBE_DEFER.
Unregister the DSI1 device manually on failure to prevent that.
Fixes: 623a3531e9cf ("drm/panel: Add driver for Novatek NT35950 DSI DriverIC panels") Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org> Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20230415-konrad-longbois-next-v1-1-ce695dc9df84@linaro.org Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
struct pmu::module must be set to the module owning the PMU driver.
Set this for the coresight etm_pmu.
Fixes: 8e264c52e1dab ("coresight: core: Allow the coresight core driver to be built as a module") Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com> Link: https://lore.kernel.org/r/20230405094922.667834-1-suzuki.poulose@arm.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
If there is no ACPI/DT information, it is assumed that L1 caches
are private and L2 (and higher) caches are shared. A cache is
'shared' between two CPUs if it is accessible from these two
CPUs.
Each CPU owns a representation (i.e. has a dedicated cacheinfo struct)
of the caches it has access to. cache_leaves_are_shared() tries to
identify whether two representations are designating the same actual
cache.
In cache_leaves_are_shared(), if 'this_leaf' is a L2 cache (or higher)
and 'sib_leaf' is a L1 cache, the caches are detected as shared as
only this_leaf's cache level is checked.
This is leads to setting sib_leaf as being shared with another CPU,
which is incorrect as this is a L1 cache.
Check 'sib_leaf->level'. Also update the comment as the function is
called when populating 'shared_cpu_map'.
Fixes: f16d1becf96f ("cacheinfo: Use cache identifiers to check if the caches are shared if available") Signed-off-by: Pierre Gondois <pierre.gondois@arm.com> Reviewed-by: Conor Dooley <conor.dooley@microchip.com> Link: https://lore.kernel.org/r/20230414081453.244787-2-pierre.gondois@arm.com Signed-off-by: Sudeep Holla <sudeep.holla@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Based on num_hid_devices, each sensor device is initialized. If
"no sensors" is initialized, amd_sfh work initialization and scheduling
doesn’t make sense and returns EOPNOTSUPP to stop driver probe. Hence,
add a check for "no sensors" enabled to handle the special case.
The initialization of SFH1.1 sensors may take some time. Hence, increase
sensor command timeouts in order to obtain status responses within a
maximum timeout.
As soon as the system is booted after shutdown, the sensors may remain in
a weird state and fail to initialize. Therefore, all sensors should be
turned off during shutdown.
Fixes: 4f567b9f8141 ("SFH: PCIe driver to add support of AMD sensor fusion hub") Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Illuminance value is actually 32 bits, but is incorrectly trancated to
16 bits. Hence convert to integer illuminace accordingly to reflect
correct values.
In order to start or stop sensors, the firmware command needs to be
changed to add an additional default subcommand value. For this reason,
add a subcommand value to enable or disable sensors accordingly.
Avoid generating an exception if there are no generic power domain(s)
registered:
(gdb) lx-genpd-summary
domain status children
/device runtime status
----------------------------------------------------------------------
Python Exception <class 'gdb.error'>: No symbol "gpd_list" in current context.
Error occurred in Python: No symbol "gpd_list" in current context.
(gdb) quit
[f.fainelli@gmail.com: correctly invoke gdb_eval_or_none] Link: https://lkml.kernel.org/r/20230327185746.3856407-1-f.fainelli@gmail.com Link: https://lkml.kernel.org/r/20230323231659.3319941-1-f.fainelli@gmail.com Fixes: 8207d4a88e1e ("scripts/gdb: add lx-genpd-summary command") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Cc: Jan Kiszka <jan.kiszka@siemens.com> Cc: Kieran Bingham <kbingham@kernel.org> Cc: Leonard Crestez <leonard.crestez@nxp.com> Cc: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Avoid generating an exception if there are no clocks registered:
(gdb) lx-clk-summary
enable prepare protect
clock count count count rate
------------------------------------------------------------------------
Python Exception <class 'gdb.error'>: No symbol "clk_root_list" in
current context.
Error occurred in Python: No symbol "clk_root_list" in current context.
Link: https://lkml.kernel.org/r/20230323225246.3302977-1-f.fainelli@gmail.com Fixes: d1e9710b63d8 ("scripts/gdb: initial clk support: lx-clk-summary") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Cc: Jan Kiszka <jan.kiszka@siemens.com> Cc: Kieran Bingham <kbingham@kernel.org> Cc: Leonard Crestez <leonard.crestez@nxp.com> Cc: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When CONFIG_PROC_FS is not set, proc_salinfo_show() is not used. Mark the
function as __maybe_unused to quieten the warning message.
../arch/ia64/kernel/salinfo.c:584:12: warning: 'proc_salinfo_show' defined but not used [-Wunused-function]
584 | static int proc_salinfo_show(struct seq_file *m, void *v)
| ^~~~~~~~~~~~~~~~~
Link: https://lkml.kernel.org/r/20230223034309.13375-1-rdunlap@infradead.org Fixes: 3f3942aca6da ("proc: introduce proc_create_single{,_data}") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
alloc_per_cpu_data() is called by find_memory(), which is marked as
__init. Therefore alloc_per_cpu_data() can also be marked as __init to
remedy this modpost problem.
Link: https://lkml.kernel.org/r/20230223034258.12917-1-rdunlap@infradead.org Fixes: 4b9ddc7cf272 ("[IA64] Fix section mismatch in contig.c version of per_cpu_init()") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
During EDR recovery, the OS must clear error status of the port that
triggered DPC even if firmware retains control of DPC and AER (see the
implementation note in the PCI Firmware spec r3.3, sec 4.6.12).
Prior to 068c29a248b6 ("PCI/ERR: Clear PCIe Device Status errors only if
OS owns AER"), the port Device Status was cleared in this path:
After 068c29a248b6, pcie_do_recovery() no longer clears Device Status when
firmware controls AER, so the error bit remains set even after recovery.
Per the "Downstream Port Containment configuration control" bit in the
returned _OSC Control Field (sec 4.5.1), the OS is allowed to clear error
status until it evaluates _OST, so clear Device Status in
edr_handle_event() if the error recovery was successful.
[bhelgaas: commit log] Fixes: 068c29a248b6 ("PCI/ERR: Clear PCIe Device Status errors only if OS owns AER") Link: https://lore.kernel.org/r/20230315235449.1279209-1-sathyanarayanan.kuppuswamy@linux.intel.com Reported-by: Tsaur Erwin <erwin.tsaur@intel.com> Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The helper generating an OF based modalias (of_device_get_modalias())
works fine, but due to the use of snprintf() internally it needs a
buffer one byte longer than what should be needed just for the entire
string (excluding the '\0'). Most users of this helper are sysfs hooks
providing the modalias string to users. They all provide a PAGE_SIZE
buffer which is way above the number of bytes required to fit the
modalias string and hence do not suffer from this issue.
There is another user though, of_device_request_module(), which is only
called by drivers/usb/common/ulpi.c. This request module function is
faulty, but maybe because in most cases there is an alternative, ULPI
driver users have not noticed it.
In this function, of_device_get_modalias() is called twice. The first
time without buffer just to get the number of bytes required by the
modalias string (excluding the null byte), and a second time, after
buffer allocation, to fill the buffer. The allocation asks for an
additional byte, in order to store the trailing '\0'. However, the
buffer *length* provided to of_device_get_modalias() excludes this extra
byte. The internal use of snprintf() with a length that is exactly the
number of bytes to be written has the effect of using the last available
byte to store a '\0', which then smashes the last character of the
modalias string.
Provide the actual size of the buffer to of_device_get_modalias() to fix
this issue.
Note: the "str[size - 1] = '\0';" line is not really needed as snprintf
will anyway end the string with a null byte, but there is a possibility
that this function might be called on a struct device_node without
compatible, in this case snprintf() would not be executed. So we keep it
just to avoid possible unbounded strings.
Cc: Stephen Boyd <sboyd@kernel.org> Cc: Peter Chen <peter.chen@kernel.org> Fixes: 9c829c097f2f ("of: device: Support loading a module with OF based modalias") Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Link: https://lore.kernel.org/r/20230404172148.82422-2-srinivas.kandagatla@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
if (vmci_host_dev->ct_type == VMCIOBJ_CONTEXT) {
// Dereferencing the wrong pointer
poll_wait(..., &context->host_context);
}
In this scenario, vmci_host_poll() reads vmci_host_dev->context first,
and then reads vmci_host_dev->ct_type to check that
vmci_host_dev->context is initialized. However, since these two reads
are not atomically executed, there is a chance of a race condition as
described above.
To fix this race condition, read vmci_host_dev->context after checking
the value of vmci_host_dev->ct_type so that vmci_host_poll() always
reads an initialized context.
Reported-by: Dae R. Jeong <threeearcat@gmail.com> Fixes: 8bf503991f87 ("VMCI: host side driver implementation.") Signed-off-by: Dae R. Jeong <threeearcat@gmail.com> Link: https://lore.kernel.org/r/ZCGFsdBAU4cYww5l@dragonet Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
CPM has the same problem as QE so for CPM also use the fix added
by commit 0398fb70940e ("spi/spi_mpc8xxx: Fix QE mode Litte Endian"):
CPM mode uses Little Endian so words > 8 bits are byte swapped.
Workaround this by always enforcing wordsize 8 for 16 and 32 bits
words. Unfortunately this will not work for LSB transfers
where wordsize is > 8 bits so disable these for now.
Also limit the workaround to 16 and 32 bits words because it can
only work for multiples of 8-bits.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu> Cc: Joakim Tjernlund <Joakim.Tjernlund@infinera.com> Fixes: 0398fb70940e ("spi/spi_mpc8xxx: Fix QE mode Litte Endian") Link: https://lore.kernel.org/r/1b7d3e84b1128f42c1887dd2fb9cdf390f541bc1.1680371809.git.christophe.leroy@csgroup.eu Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
pci1xxxx_spi_resume API masks SPI interrupt bit which prohibits interrupt
from coming to the host at the end of the transaction after suspend-resume.
This patch unmasks this bit at resume.
Fixes: 1cc0cbea7167 ("spi: microchip: pci1xxxx: Add driver for SPI controller of PCI1XXXX PCIe switch") Signed-off-by: Tharun Kumar P <tharunkumar.pasumarthi@microchip.com> Link: https://lore.kernel.org/r/20230404171613.1336093-3-tharunkumar.pasumarthi@microchip.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
In pci1xxxx_spi_transfer_one API, length of SPI transaction gets cleared
by setting of length mask. Set length of transaction only after masking
length field.
Fixes: 1cc0cbea7167 ("spi: microchip: pci1xxxx: Add driver for SPI controller of PCI1XXXX PCIe switch") Signed-off-by: Tharun Kumar P <tharunkumar.pasumarthi@microchip.com> Link: https://lore.kernel.org/r/20230404171613.1336093-2-tharunkumar.pasumarthi@microchip.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Any power domain would already have been attached by the platform bus
code so drop the bogus power domain attach which always succeeds from
probe.
This effectively reverts commit 7de109c0abe9 ("interconnect: icc-rpm:
Add support for bus power domain").
Fixes: 7de109c0abe9 ("interconnect: icc-rpm: Add support for bus power domain") Cc: Yassine Oudjana <y.oudjana@protonmail.com> Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Tested-by: Konrad Dybcio <konrad.dybcio@linaro.org> # MSM8996 Sony Kagura Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Link: https://lore.kernel.org/r/20230313084953.24088-3-johan+linaro@kernel.org Signed-off-by: Georgi Djakov <djakov@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Returning early in a platform driver's remove callback is wrong. In this
case the dma resources are not released in the error path. this is never
retried later and so this is a permanent leak. To fix this, only skip
hardware disabling if waking the device fails.
Fixes: 64ff247a978f ("spi: Add Qualcomm QUP SPI controller support") Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Link: https://lore.kernel.org/r/20230330210341.2459548-2-u.kleine-koenig@pengutronix.de Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The driver is able to work fine without relying on a mandatory interrupt
being assigned to the I2C device. This is only needed when making use of
the jack-detect support.
However, the following warning message is always emitted when there is
no such interrupt available:
es8316 0-0011: Failed to get IRQ 0: -22
Do not attempt to request an IRQ if it is not available/valid. This also
ensures the rather misleading message is not displayed anymore.
Also note the IRQ validation relies on commit dab472eb931bc291 ("i2c /
ACPI: Use 0 to indicate that device does not have interrupt assigned").
Fixes: 822257661031 ("ASoC: es8316: Add jack-detect support") Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20230328094901.50763-1-cristian.ciocaltea@collabora.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
commit bb38919ec56e ("PCI: imx6: Add support for i.MX6 PCIe controller")
added a fault hook to this driver in the probe function. So it was only
installed if needed.
commit bde4a5a00e76 ("PCI: imx6: Allow probe deferral by reset GPIO")
moved it from probe to driver init which installs the hook unconditionally
as soon as the driver is compiled into a kernel.
When this driver is compiled as a module, the hook is not registered
until after the driver has been matched with a .compatible and
loaded.
commit 2d8ed461dbc9 ("PCI: imx6: Add support for i.MX8MQ")
added some protection for non-ARM architectures, but this does not
protect non-i.MX ARM architectures.
Since fault handlers can be triggered on any architecture for different
reasons, there is no guarantee that they will be triggered only for the
assumed situation, leading to improper error handling (i.MX6-specific
imx6q_pcie_abort_handler) on foreign systems.
I had seen strange L3 imprecise external abort messages several times on
OMAP4 and OMAP5 devices and couldn't make sense of them until I realized
they were related to this unused imx6q driver because I had
CONFIG_PCI_IMX6=y.
Note that CONFIG_PCI_IMX6=y is useful for kernel binaries that are designed
to run on different ARM SoC and be differentiated only by device tree
binaries. So turning off CONFIG_PCI_IMX6 is not a solution.
Therefore we check the compatible in the init function before registering
the fault handler.
Link: https://lore.kernel.org/r/e1bcfc3078c82b53aa9b78077a89955abe4ea009.1678380991.git.hns@goldelico.com Fixes: bde4a5a00e76 ("PCI: imx6: Allow probe deferral by reset GPIO") Fixes: 415b6185c541 ("PCI: imx6: Fix config read timeout handling") Fixes: 2d8ed461dbc9 ("PCI: imx6: Add support for i.MX8MQ") Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com> Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org> Reviewed-by: Richard Zhu <hongxing.zhu@nxp.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>