Andrew Jeffery [Tue, 18 Jul 2017 05:24:52 +0000 (14:54 +0930)]
pinctrl: aspeed: g4: Add USB device and host support
Implement the AST2400 USB functions as described by the devicetree
bindings. Three ports are fully documented in the datasheet and exposed
through the bindings and pinctrl, though there are remnants of
documentation for a fourth port muxed with GPIO pins GPIOQ6 and GPIOQ7.
The implementation is updated to reflect this but the function and
group are not exposed.
Disregarding the mostly undocumented fourth port, the USB functions are
an outlier with respect to the rest of the muxed functionality on the
AST2400 as GPIO is not supported on these pins.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Andrew Jeffery [Tue, 18 Jul 2017 05:24:51 +0000 (14:54 +0930)]
dt-bindings: pinctrl: aspeed: Add g5 USB functions
The Aspeed AST2500 SoC contains a number of USB controllers:
* USB 1.1 Host Controller
* USB 2.0 Host Controller (x2)
* USB 2.0 Virtual Hub
* USB 2.0 Device Controller
* USB 1.1 HID Controller
The controllers are exposed via two USB ports with functionality muxed
as required. The following table illustrates the relationships between
the ports and the controllers via the mux function names:
Port | USB Version | USB Mode | Mux Function
------|--------------|--------------|-------------
A | 2.0 | Virtual Hub | USB2AD
A | 2.0 | Host | USB2AH
B | 1.1 | HID | USB11BHID
B | 2.0 | Device | USB2BD
B | 2.0 | Host | USB2BH
Signed-off-by: Andrew Jeffery <andrew@aj.id.au> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Andrew Jeffery [Tue, 18 Jul 2017 05:24:50 +0000 (14:54 +0930)]
dt-bindings: pinctrl: aspeed: Add g4 USB functions
The AST2400 contains several USB controllers:
* USB 1.1 Host Controller
* USB 2.0 Host Controller
* USB 2.0 Virtual Hub
* USB 1.1 HID Controller
Pins for three ports are routed to the three controllers such that:
* Port 1 is a dedicated USB 1.1 host port
* Port 2 is shared between the USB 1.1 host and HID controllers
* Port 3 is shared between the USB 2.0 host and Hub controllers
As the pins for port 1 are fixed function there is no associated mux
function or group described in the bindings. Ports 2 and 3 are muxed as
above, and the table below describes the mapping between pinmux function
names and ports:
Port | USB Version | USB Mode | Mux Function
------|--------------|-----------|-------------
1 | 1.1 | Host | -
2 | 1.1 | Host | USB11H2
2 | 1.1 | HID | USB11D1
3 | 2.0 | Host | USB2H1
3 | 2.0 | Device | USB2D1
Signed-off-by: Andrew Jeffery <andrew@aj.id.au> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pinctrl: zte: fix 'functions' allocation in zx_pinctrl_build_state()
It fixes the following Smatch static check warning:
drivers/pinctrl/zte/pinctrl-zx.c:338 zx_pinctrl_build_state()
warn: passing devm_ allocated variable to kfree.
As we will be calling krealloc() on pointer 'functions', which means
kfree() will be called in there, devm_kzalloc() shouldn't be used with
the allocation in the first place. Fix the warning by calling kcalloc()
and managing the free procedure in error path on our own.
@ok@
identifier r.i;
expression e;
position p;
@@
e = i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct gpio_chip e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct gpio_chip i = { ... };
In the following log you can see a significant difference in the code size
and data segment, hence in the dec segment. This log is the output
of the size command, before and after the code change:
before:
text data bss dec hex filename
15136 5112 0 20248 4f18 drivers/pinctrl/qcom/pinctrl-ssbi-mpp.o
@ok@
identifier r.i;
expression e;
position p;
@@
e = i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct gpio_chip e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct gpio_chip i = { ... };
In the following log you can see a significant difference in the code size
and data segment, hence in the dec segment. This log is the output
of the size command, before and after the code change:
before:
text data bss dec hex filename
18958 9000 128 28086 6db6 drivers/pinctrl/bcm/pinctrl-bcm2835.o
after:
text data bss dec hex filename
18764 8912 128 27804 6c9c drivers/pinctrl/bcm/pinctrl-bcm2835.o
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com> Acked-by: Eric Anholt <eric@anholt.net> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch fixes the below warning
--> Prefer 'unsigned int' to bare use of 'unsigned'.
--> line over 80 characters.
--> Prefer 'unsigned int **' to bare use of 'unsigned **'.
Signed-off-by: Nava kishore Manne <navam@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
@ok@
identifier r.i;
expression e;
position p;
@@
e = i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct gpio_chip e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct gpio_chip i = { ... };
In the following log you can see a significant difference in the code size
and data segment, hence in the dec segment. This log is the output
of the size command, before and after the code change:
before:
text data bss dec hex filename
21671 3632 128 25431 6357 drivers/pinctrl/pinctrl-st.o
after:
text data bss dec hex filename
21366 3576 128 25070 61ee drivers/pinctrl/pinctrl-st.o
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com> Acked-by: Patrice Chotard <patrice.chotard@st.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Hans de Goede [Wed, 12 Jul 2017 12:31:01 +0000 (14:31 +0200)]
pinctrl: baytrail: Do not call WARN_ON for a firmware bug
WARN_ON causes a backtrace to get logged which is only useful for
kernel bugs. For signalling a firmware bug dev_warn(dev, FW_BUG "...")
should be used.
This fixes users running userspace software to monitor kernel oopses
getting a false positive bug-report every boot because of the wrong
use of WARN_ON.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pinctrl: imx: make imx_pmx_ops.gpio_set_direction platform specific callbacks
Various IMX platforms may have different imx_pmx_ops.gpio_set_direction
implementations, so let's make it platform specific callbacks instead of
the fixed common one.
Currently only VF610 platform implements it. No function level changes.
pinctrl: imx: remove gpio_request_enable and gpio_disable_free
gpio_request_enable/disable_free actually are not quite necessary as
standard IMX pinctrl binding already sets GPIO mux from device tree,
e.g. VF610_PAD_PTB20__GPIO_42 or MX7D_PAD_SD2_CD_B__GPIO5_IO9
No need to do it again in gpio_request_enable.
And according to Stefan:
"For all GPIO I checked in upstream device trees we assign a pinctrl
to the same node, so in all cases gpio_request_enable/disable is really
unnecessary."
So it should be safe to simply remove it.
Note that this changes semantics for Vybrid, e.g.
"The two functions have been introduced for Vybrid (through
SHARE_MUX_CONF_REG) and mux pins as GPIOs automatically when a GPIO
gets requested. The automatic mux is optional by the pinmux/gpio
subsystem semantics, and other NXP devices do not use it, instead an
explicit pinctrl node is added in the device tree to mux GPIOs where
required. Hence this change aligns Vybrid to other NXP (i.MX) devices.
Note that all upstream device tree assign proper pinctrl properties
where GPIOs are used so no change is necessary for device trees."
pinctrl: uniphier: omit redundant input enable bit information
For LD11/20 SoCs (capable of per-pin input enable), the iectrl bit
number matches its pin number. So, this is redundant information.
Instead, we just need a flag to know if the iectrl gating exists or not.
With this refactoring, 5 bits in pin data will be saved.
There are a bunch of GPIO muxing data, but most of them are actually
unneeded because GPIO-to-pin mapping can be specified by "gpio-ranges"
DT properties.
Tables that contain a set of GPIO pins are still needed for the named
mapping by "gpio-ranges-group-names". This is a much cleaner way for
UniPhier SoC family where GPIO numbers are not straight mapped to pin
numbers.
pinctrl: uniphier: fix pin_config_get() for input-enable
For LD11/LD20 SoCs (capable of per-pin input enable), iectrl bits are
located across multiple registers. So, the register offset must be
taken into account. Otherwise, wrong input-enable status is displayed.
While we here, rename the macro because it is a base address.
Fixes: aa543888ca8c ("pinctrl: uniphier: support per-pin input enable for new SoCs") Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
@ok@
identifier r.i;
expression e;
position p;
@@
e = i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct gpio_chip e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct gpio_chip i = { ... };
In the following log you can see a significant difference in the code size
and data segment, hence in the dec segment. This log is the output
of the size command, before and after the code change:
before:
text data bss dec hex filename
13129 2808 192 16129 3f01 drivers/pinctrl/qcom/pinctrl-msm.o
after:
text data bss dec hex filename
12839 2720 192 15751 3d87 drivers/pinctrl/qcom/pinctrl-msm.o
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
@ok@
identifier r.i;
expression e;
position p;
@@
e = i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct gpio_chip e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct gpio_chip i = { ... };
In the following log you can see a significant difference in the code size
and data segment, hence in the dec segment. This log is the output
of the size command, before and after the code change:
before:
text data bss dec hex filename
17061 6992 0 24053 5df5 drivers/pinctrl/qcom/pinctrl-ssbi-gpio.o
after:
text data bss dec hex filename
16777 6904 0 23681 5c81 drivers/pinctrl/qcom/pinctrl-ssbi-gpio.o
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
@ok@
identifier r.i;
expression e;
position p;
@@
e = i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct gpio_chip e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct gpio_chip i = { ... };
In the following log you can see a significant difference in the code size
and data segment, hence in the dec segment. This log is the output
of the size command, before and after the code change:
before:
text data bss dec hex filename
12775 3696 64 16535 4097 drivers/pinctrl/pinctrl-coh901.o
@ok@
identifier r.i;
expression e;
position p;
@@
e = i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct gpio_chip e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct gpio_chip i = { ... };
In the following log you can see a significant difference in the code size
and data segment, hence in the dec segment. This log is the output
of the size command, before and after the code change:
before:
text data bss dec hex filename
17545 5376 0 22921 5989 drivers/pinctrl/nomadik/pinctrl-abx500.o
@ok@
identifier r.i;
expression e;
position p;
@@
e = i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct gpio_chip e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct gpio_chip i = { ... };
In the following log you can see a significant difference in the code size
and data segment, hence in the dec segment. This log is the output
of the size command, before and after the code change:
before:
text data bss dec hex filename
7754 2328 0 10082 2762 drivers/pinctrl/vt8500/pinctrl-wmt.o
after:
text data bss dec hex filename
7472 2272 0 9744 2610 drivers/pinctrl/vt8500/pinctrl-wmt.o
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
@ok@
identifier r.i;
expression e;
position p;
@@
e = i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct gpio_chip e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct gpio_chip i = { ... };
In the following log you can see a significant difference in the code size
and data segment, hence in the dec segment. This log is the output
of the size command, before and after the code change:
before:
text data bss dec hex filename
11866 3520 128 15514 3c9a drivers/pinctrl/pinctrl-rza1.o
after:
text data bss dec hex filename
11539 3464 128 15131 3b1b drivers/pinctrl/pinctrl-rza1.o
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pinctrl: msm: add support to configure ipq40xx GPIO_PULL bits
GPIO_PULL bits configurations in TLMM_GPIO_CFG register
differs for IPQ40xx from rest of the other qcom SoCs.
As it does not support the keeper state and therefore can't
support bias-bus-hold property.
This patch adds a pull_no_keeper setting which configures the
msm_gpio_pull bits for ipq40xx. This is required to fix the
proper configurations of gpio-pull bits for nand pins mux.
IPQ40xx SoC:
2'b10: Internal pull up enable.
2'b11: Unsupport
For other SoC's:
2'b10: Keeper
2'b11: Pull-Up
Note: Due to pull_no_keeper length, all kerneldoc entries
in the msm_pinctrl_soc_data struct had to be realigned.
pinctrl: qcom: ipq4019: add most remaining pin definitions
This patch adds multiple pinctrl functions and mappings
for SDIO, NAND, I2S, WIFI, PCIE, LEDs, etc... that have
been missing from the current minimal version.
This patch has been updated from the original version
that was posted by Ram Chandra Jangir on the LEDE-DEV ML:
<https://patchwork.ozlabs.org/patch/752962/>. A short
summary of the changes are documented in the device-tree
patch of this series:
"dt-bindings: pinctrl: add most other IPQ4019 pin functions and groups"
dt-bindings: pinctrl: add most other IPQ4019 pin functions and groups
This patch adds the remaining pin functions and mux groups.
All unknown and debug functions are omitted. Existing functions
for qpic, sdio, rgmii, rmii, wifi/d are squashed together as
much as possible. And only in case of a clash, the individually
named functions have been kept. The exceptions are:
led0-11
i2s_rx, i2s_tx, i2s_td, i2s_spdif_in, i2s_spdif_out,
smart0-3
Cc: Varadarajan Narayanan <varada@codeaurora.org> Cc: Ram Chandra Jangir <rjangir@codeaurora.org> Cc: John Crispin <john@phrozen.org> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Torvalds [Sun, 13 Aug 2017 22:34:28 +0000 (15:34 -0700)]
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS fixes from Ralf Baechle:
"Another round of MIPS fixes:
- compressed boot: Ignore a generated .c file
- VDSO: Fix a register clobber list
- DECstation: Fix an int-handler.S CPU_DADDI_WORKAROUNDS regression
- Octeon: Fix recent cleanups that cleaned away a bit too much thus
breaking the arch side of the EDAC and USB drivers.
- uasm: Fix duplicate const in "const struct foo const bar[]" which
GCC 7.1 no longer accepts.
- Fix race on setting and getting cpu_online_mask
- Fix preemption issue. To do so cleanly introduce macro to get the
size of L3 cache line.
- Revert include cleanup that sometimes results in build error
- MicroMIPS uses bit 0 of the PC to indicate microMIPS mode. Make
sure this bit is set for kernel entry as well.
- Prevent configuring the kernel for both microMIPS and MT. There are
no such CPUs currently and thus the combination is unsupported and
results in build errors.
This has been sitting in linux-next for a few days and has survived
automated testing by Imagination's test farm. No known regressions
pending except a number of issues that crept up due to lots of people
switching to GCC 7.1"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Set ISA bit in entry-y for microMIPS kernels
MIPS: Prevent building MT support for microMIPS kernels
MIPS: PCI: Fix smp_processor_id() in preemptible
MIPS: Introduce cpu_tcache_line_size
MIPS: DEC: Fix an int-handler.S CPU_DADDI_WORKAROUNDS regression
MIPS: VDSO: Fix clobber lists in fallback code paths
Revert "MIPS: Don't unnecessarily include kmalloc.h into <asm/cache.h>."
MIPS: OCTEON: Fix USB platform code breakage.
MIPS: Octeon: Fix broken EDAC driver.
MIPS: gitignore: ignore generated .c files
MIPS: Fix race on setting and getting cpu_online_mask
MIPS: mm: remove duplicate "const" qualifier on insn_table
Linus Torvalds [Sun, 13 Aug 2017 19:44:18 +0000 (12:44 -0700)]
Merge tag 'driver-core-4.13-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are three firmware core fixes for 4.13-rc5.
All three of these fix reported issues and have been floating around
for a few weeks. They have been in linux-next with no reported
problems"
* tag 'driver-core-4.13-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
firmware: avoid invalid fallback aborts by using killable wait
firmware: fix batched requests - send wake up on failure on direct lookups
firmware: fix batched requests - wake all waiters
Linus Torvalds [Sun, 13 Aug 2017 19:41:58 +0000 (12:41 -0700)]
Merge tag 'char-misc-4.13-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc fixes from Greg KH:
"Here are two patches for 4.13-rc5.
One is a fix for a reported thunderbolt issue, and the other a fix for
an MEI driver issue. Both have been in linux-next with no reported
issues"
* tag 'char-misc-4.13-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
thunderbolt: Do not enumerate more ports from DROM than the controller has
mei: exclude device from suspend direct complete optimization
Linus Torvalds [Sun, 13 Aug 2017 19:33:35 +0000 (12:33 -0700)]
Merge tag 'tty-4.13-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are two tty serial driver fixes for 4.13-rc5. One is a revert of
a -rc1 patch that turned out to not be a good idea, and the other is a
fix for the pl011 serial driver.
Both have been in linux-next with no reported issues"
* tag 'tty-4.13-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
Revert "serial: Delete dead code for CIR serial ports"
tty: pl011: fix initialization order of QDF2400 E44
Linus Torvalds [Sun, 13 Aug 2017 19:30:17 +0000 (12:30 -0700)]
Merge tag 'staging-4.13-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/iio fixes from Greg KH:
"Here are some Staging and IIO driver fixes for 4.13-rc5.
Nothing major, just a number of small fixes for reported issues. All
of these have been in linux-next for a while now with no reported
issues. Full details are in the shortlog"
* tag 'staging-4.13-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: comedi: comedi_fops: do not call blocking ops when !TASK_RUNNING
iio: aspeed-adc: wait for initial sequence.
iio: accel: bmc150: Always restore device to normal mode after suspend-resume
staging:iio:resolver:ad2s1210 fix negative IIO_ANGL_VEL read
iio: adc: axp288: Fix the GPADC pin reading often wrongly returning 0
iio: adc: vf610_adc: Fix VALT selection value for REFSEL bits
iio: accel: st_accel: add SPI-3wire support
iio: adc: Revert "axp288: Drop bogus AXP288_ADC_TS_PIN_CTRL register modifications"
iio: adc: sun4i-gpadc-iio: fix unbalanced irq enable/disable
iio: pressure: st_pressure_core: disable multiread by default for LPS22HB
iio: light: tsl2563: use correct event code
Linus Torvalds [Sun, 13 Aug 2017 19:27:42 +0000 (12:27 -0700)]
Merge tag 'usb-4.13-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of small USB driver fixes and new device ids for
4.13-rc5. There is the usual gadget driver fixes, some new quirks for
"messy" hardware, and some new device ids.
All have been in linux-next with no reported issues"
* tag 'usb-4.13-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: serial: pl2303: add new ATEN device id
usb: quirks: Add no-lpm quirk for Moshi USB to Ethernet Adapter
USB: Check for dropped connection before switching to full speed
usb:xhci:Add quirk for Certain failing HP keyboard on reset after resume
usb: renesas_usbhs: gadget: fix unused-but-set-variable warning
usb: renesas_usbhs: Fix UGCTRL2 value for R-Car Gen3
usb: phy: phy-msm-usb: Fix usage of devm_regulator_bulk_get()
usb: gadget: udc: renesas_usb3: Fix usb_gadget_giveback_request() calling
usb: dwc3: gadget: Correct ISOC DATA PIDs for short packets
USB: serial: option: add D-Link DWM-222 device ID
usb: musb: fix tx fifo flush handling again
usb: core: unlink urbs from the tail of the endpoint's urb_list
usb-storage: fix deadlock involving host lock and scsi_done
uas: Add US_FL_IGNORE_RESIDUE for Initio Corporation INIC-3069
USB: hcd: Mark secondary HCD as dead if the primary one died
USB: serial: cp210x: add support for Qivicon USB ZigBee dongle
Linus Torvalds [Sat, 12 Aug 2017 23:19:43 +0000 (16:19 -0700)]
Merge tag 'for-linus-20170812' of git://git.infradead.org/linux-mtd
Pull another MTD fix from Brian Norris:
"An mtdblock regression occurred in -rc1 (all writes were broken!), in
the process of some block subsystem refactoring. Noticed and fixed
last week, but I'm a little slow on the uptake"
* tag 'for-linus-20170812' of git://git.infradead.org/linux-mtd:
mtd: blkdevs: Fix mtd block write failure
Linus Torvalds [Sat, 12 Aug 2017 16:01:36 +0000 (09:01 -0700)]
Merge tag 'for-linus-4.13b-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
"Some fixes for Xen:
- a fix for a regression introduced in 4.13 for a Xen HVM-guest
configured with KASLR
- a fix for a possible deadlock in the xenbus driver when booting the
system
- a fix for lost interrupts in Xen guests"
* tag 'for-linus-4.13b-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/events: Fix interrupt lost during irq_disable and irq_enable
xen: avoid deadlock in xenbus
xen: fix hvm guest with kaslr enabled
xen: split up xen_hvm_init_shared_info()
x86: provide an init_mem_mapping hypervisor hook
Linus Torvalds [Fri, 11 Aug 2017 20:54:09 +0000 (13:54 -0700)]
Merge tag 'nfs-for-4.13-5' of git://git.linux-nfs.org/projects/anna/linux-nfs
Pull NFS client fixes from Anna Schumaker:
"A few more NFS client bugfixes from me for rc5.
Dros has a stable fix for flexfiles to prevent leaking the
nfs4_ff_ds_version arrays when freeing a layout, Trond fixed a
potential recovery loop situation with the TEST_STATEID operation, and
Christoph fixed up the pNFS blocklayout Kconfig options to prevent
unsafe use with kernels that don't have large block device support.
Summary:
Other fixes:
- improve TEST_STATEID OLD_STATEID handling to prevent recovery loop
- require 64-bit sector_t for pNFS blocklayout to prevent 32-bit
compile errors"
* tag 'nfs-for-4.13-5' of git://git.linux-nfs.org/projects/anna/linux-nfs:
pnfs/blocklayout: require 64-bit sector_t
NFSv4: Ignore NFS4ERR_OLD_STATEID in nfs41_check_open_stateid()
nfs/flexfiles: fix leak of nfs4_ff_ds_version arrays
Linus Torvalds [Fri, 11 Aug 2017 19:26:49 +0000 (12:26 -0700)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"A set of fixes that should go into this series. This contains:
- Fix from Bart for blk-mq requeue queue running, preventing a
continued loop of run/restart.
- Fix for a bio/blk-integrity issue, in two parts. One from
Christoph, fixing where verification happens, and one from Milan,
for a NULL profile.
- NVMe pull request, most of the changes being for nvme-fc, but also
a few trivial core/pci fixes"
* 'for-linus' of git://git.kernel.dk/linux-block:
nvme: fix directive command numd calculation
nvme: fix nvme reset command timeout handling
nvme-pci: fix CMB sysfs file removal in reset path
lpfc: support nvmet_fc defer_rcv callback
nvmet_fc: add defer_req callback for deferment of cmd buffer return
nvme: strip trailing 0-bytes in wwid_show
block: Make blk_mq_delay_kick_requeue_list() rerun the queue at a quiet time
bio-integrity: only verify integrity on the lowest stacked driver
bio-integrity: Fix regression if profile verify_fn is NULL
Linus Torvalds [Fri, 11 Aug 2017 18:56:54 +0000 (11:56 -0700)]
Merge tag 'mmc-v4.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"MMC core:
- fix lockdep splat when removing mmc_block module
- fix the logic for setting eMMC HS400ES signal voltage
MMC host:
- omap_hsmmc: add CMD23 capability to fix -EIO errors"
* tag 'mmc-v4.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: block: fix lockdep splat when removing mmc_block module
mmc: mmc: correct the logic for setting HS400ES signal voltage
mmc: host: omap_hsmmc: Add CMD23 capability to omap_hsmmc driver
Linus Torvalds [Fri, 11 Aug 2017 18:44:18 +0000 (11:44 -0700)]
Merge tag 'fbdev-v4.13-rc5' of git://github.com/bzolnier/linux
Pull fbdev fixes from Bartlomiej Zolnierkiewicz:
- allow user to disable write combined mapping in efifb driver (Dave
Airlie)
- fix use after free bugs on driver removal in imxfb driver (Dan
Carpenter)
- fix unused variable warning in omapfb driver (Arnd Bergmann)
* tag 'fbdev-v4.13-rc5' of git://github.com/bzolnier/linux:
efifb: allow user to disable write combined mapping.
fbdev: omapfb: remove unused variable
video: fbdev: imxfb: use after free in imxfb_remove()
Linus Torvalds [Fri, 11 Aug 2017 18:20:48 +0000 (11:20 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse
Pull fuse fixes from Miklos Szeredi:
"Fix a few bugs in fuse"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: set mapping error in writepage_locked when it fails
fuse: Dont call set_page_dirty_lock() for ITER_BVEC pages for async_dio
fuse: initialize the flock flag in fuse_file on allocation
Linus Torvalds [Fri, 11 Aug 2017 18:15:51 +0000 (11:15 -0700)]
Merge tag 'iommu-fixes-v4.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fix from Joerg Roedel:
"Fix a NULL-pointer dereference in arm_smmu_add_device"
* tag 'iommu-fixes-v4.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/arm-smmu: fix null-pointer dereference in arm_smmu_add_device
The blocklayout code does not compile cleanly for a 32-bit sector_t,
and also has no reliable checks for devices sizes, which makes it
unsafe to use with a kernel that doesn't support large block devices.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reported-by: Arnd Bergmann <arnd@arndb.de> Fixes: 5c83746a0cf2 ("pnfs/blocklayout: in-kernel GETDEVICEINFO XDR parsing") Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Artem Savkov [Tue, 8 Aug 2017 10:26:02 +0000 (12:26 +0200)]
iommu/arm-smmu: fix null-pointer dereference in arm_smmu_add_device
Commit c54451a "iommu/arm-smmu: Fix the error path in arm_smmu_add_device"
removed fwspec assignment in legacy_binding path as redundant which is
wrong. It needs to be updated after fwspec initialisation in
arm_smmu_register_legacy_master() as it is dereferenced later. Without
this there is a NULL-pointer dereference panic during boot on some hosts.
Signed-off-by: Artem Savkov <asavkov@redhat.com> Reviewed-by: Robin Murphy <robin.murphy@arm.com> Acked-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Joerg Roedel <jroedel@suse.de>
Liu Shuo [Sat, 29 Jul 2017 16:59:57 +0000 (00:59 +0800)]
xen/events: Fix interrupt lost during irq_disable and irq_enable
Here is a device has xen-pirq-MSI interrupt. Dom0 might lost interrupt
during driver irq_disable/irq_enable. Here is the scenario,
1. irq_disable -> disable_dynirq -> mask_evtchn(irq channel)
2. dev interrupt raised by HW and Xen mark its evtchn as pending
3. irq_enable -> startup_pirq -> eoi_pirq ->
clear_evtchn(channel of irq) -> clear pending status
4. consume_one_event process the irq event without pending bit assert
which result in interrupt lost once
5. No HW interrupt raising anymore.
Now use enable_dynirq for enable_pirq of xen_pirq_chip to remove
eoi_pirq when irq_enable.
Signed-off-by: Liu Shuo <shuo.a.liu@intel.com> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Juergen Gross <jgross@suse.com>
A Xen HVM guest running with KASLR enabled will die rather soon today
because the shared info page mapping is using va() too early. This was
introduced by commit a5d5f328b0e2baa5ee7c119fd66324eb79eeeb66 ("xen:
allocate page for shared info page from low memory").
In order to fix this use early_memremap() to get a temporary virtual
address for shared info until va() can be used safely.
Instead of calling xen_hvm_init_shared_info() on boot and resume split
it up into a boot time function searching for the pfn to use and a
mapping function doing the hypervisor mapping call.
Jeff Layton [Thu, 25 May 2017 10:57:50 +0000 (06:57 -0400)]
fuse: set mapping error in writepage_locked when it fails
This ensures that we see errors on fsync when writeback fails.
Signed-off-by: Jeff Layton <jlayton@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Jan Kara <jack@suse.cz> Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Linus Torvalds [Fri, 11 Aug 2017 05:33:47 +0000 (22:33 -0700)]
Merge tag 'drm-fixes-for-v4.13-rc5' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Nothing too earth shattering here, it just seems like lots of little
things all over the place.
msm has probably the larger amount of changes, but they all seem fine,
otherwise, some rockchip, i915, etnaviv and exynos fixes, along with
one nouveau regression fix for some older GPUs"
* tag 'drm-fixes-for-v4.13-rc5' of git://people.freedesktop.org/~airlied/linux: (35 commits)
drm/nouveau/disp/nv04: avoid creation of output paths
drm: make DRM_STM default n
drm/exynos: forbid creating framebuffers from too small GEM buffers
drm/etnaviv: Fix off-by-one error in reloc checking
drm/i915: fix backlight invert for non-zero minimum brightness
drm/i915/shrinker: Wrap need_resched() inside preempt-disable
drm/i915/perf: fix flex eu registers programming
drm/i915: Fix out-of-bounds array access in bdw_load_gamma_lut
drm/i915/gvt: Change the max length of mmio_reg_rw from 4 to 8
drm/i915/gvt: Initialize MMIO Block with HW state
drm/rockchip: vop: report error when check resource error
drm/rockchip: vop: round_up pitches to word align
drm/rockchip: vop: fix NV12 video display error
drm/rockchip: vop: fix iommu page fault when resume
drm/i915/gvt: clean workload queue if error happened
drm/i915/gvt: change resetting to resetting_eng
drm/msm: gpu: don't abuse dma_alloc for non-DMA allocations
drm/msm: gpu: call qcom_mdt interfaces only for ARCH_QCOM
drm/msm/adreno: Prevent unclocked access when retrieving timestamps
drm/msm: Remove __user from __u64 data types
...
Linus Torvalds [Thu, 10 Aug 2017 23:20:52 +0000 (16:20 -0700)]
Merge branch 'akpm' (patches from Andrew)
Merge misc fixes from Andrew Morton:
"21 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (21 commits)
userfaultfd: replace ENOSPC with ESRCH in case mm has gone during copy/zeropage
zram: rework copy of compressor name in comp_algorithm_store()
rmap: do not call mmu_notifier_invalidate_page() under ptl
mm: fix list corruptions on shmem shrinklist
mm/balloon_compaction.c: don't zero ballooned pages
MAINTAINERS: copy virtio on balloon_compaction.c
mm: fix KSM data corruption
mm: fix MADV_[FREE|DONTNEED] TLB flush miss problem
mm: make tlb_flush_pending global
mm: refactor TLB gathering API
Revert "mm: numa: defer TLB flush for THP migration as long as possible"
mm: migrate: fix barriers around tlb_flush_pending
mm: migrate: prevent racy access to tlb_flush_pending
fault-inject: fix wrong should_fail() decision in task context
test_kmod: fix small memory leak on filesystem tests
test_kmod: fix the lock in register_test_dev_kmod()
test_kmod: fix bug which allows negative values on two config options
test_kmod: fix spelling mistake: "EMTPY" -> "EMPTY"
userfaultfd: hugetlbfs: remove superfluous page unlock in VM_SHARED case
mm: ratelimit PFNs busy info message
...
Mike Rapoport [Thu, 10 Aug 2017 22:24:32 +0000 (15:24 -0700)]
userfaultfd: replace ENOSPC with ESRCH in case mm has gone during copy/zeropage
When the process exit races with outstanding mcopy_atomic, it would be
better to return ESRCH error. When such race occurs the process and
it's mm are going away and returning "no such process" to the uffd
monitor seems better fit than ENOSPC.
Link: http://lkml.kernel.org/r/1502111545-32305-1-git-send-email-rppt@linux.vnet.ibm.com Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com> Suggested-by: Michal Hocko <mhocko@suse.com> Acked-by: Michal Hocko <mhocko@suse.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: "Dr. David Alan Gilbert" <dgilbert@redhat.com> Cc: Pavel Emelyanov <xemul@virtuozzo.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
zram: rework copy of compressor name in comp_algorithm_store()
comp_algorithm_store() passes the size of the source buffer to strlcpy()
instead of the destination buffer size. Make it explicit that the two
buffers have the same size and use strcpy() instead of strlcpy(). The
latter can be done safely since the function ensures that the string in
the source buffer is terminated.
Link: http://lkml.kernel.org/r/20170803163350.45245-1-mka@chromium.org Signed-off-by: Matthias Kaehlcke <mka@chromium.org> Reviewed-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Acked-by: Minchan Kim <minchan@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The problem is that shmem_unused_huge_shrink() moves entries from the
global sbinfo->shrinklist to its local lists and then releases the
spinlock. However, a parallel shmem_setattr() could access one of these
entries directly and add it back to the global shrinklist if it is
removed, with the spinlock held.
The logic itself looks solid since an entry could be either in a local
list or the global list, otherwise it is removed from one of them by
list_del_init(). So probably the race condition is that, one CPU is in
the middle of INIT_LIST_HEAD() but the other CPU calls list_empty()
which returns true too early then the following list_add_tail() sees a
corrupted entry.
list_empty_careful() is designed to fix this situation.
Wei Wang [Thu, 10 Aug 2017 22:24:21 +0000 (15:24 -0700)]
mm/balloon_compaction.c: don't zero ballooned pages
Revert commit bb01b64cfab7 ("mm/balloon_compaction.c: enqueue zero page
to balloon device")'
Zeroing ballon pages is rather time consuming, especially when a lot of
pages are in flight. E.g. 7GB worth of ballooned memory takes 2.8s with
__GFP_ZERO while it takes ~491ms without it.
The original commit argued that zeroing will help ksmd to merge these
pages on the host but this argument is assuming that the host actually
marks balloon pages for ksm which is not universally true. So we pay
performance penalty for something that even might not be used in the end
which is wrong. The host can zero out pages on its own when there is a
need.
[mhocko@kernel.org: new changelog text] Link: http://lkml.kernel.org/r/1501761557-9758-1-git-send-email-wei.w.wang@intel.com Fixes: bb01b64cfab7 ("mm/balloon_compaction.c: enqueue zero page to balloon device") Signed-off-by: Wei Wang <wei.w.wang@intel.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Michal Hocko <mhocko@suse.com> Cc: zhenwei.pi <zhenwei.pi@youruncloud.com> Cc: David Hildenbrand <david@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Changes to mm/balloon_compaction.c can easily break virtio, and virtio
is the only user of that interface. Add a line to MAINTAINERS so
whoever changes that file remembers to copy us.
Link: http://lkml.kernel.org/r/1501764010-24456-1-git-send-email-mst@redhat.com Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Rafael Aquini <aquini@redhat.com> Acked-by: Wei Wang <wei.w.wang@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Minchan Kim [Thu, 10 Aug 2017 22:24:15 +0000 (15:24 -0700)]
mm: fix KSM data corruption
Nadav reported KSM can corrupt the user data by the TLB batching
race[1]. That means data user written can be lost.
Quote from Nadav Amit:
"For this race we need 4 CPUs:
CPU0: Caches a writable and dirty PTE entry, and uses the stale value
for write later.
CPU1: Runs madvise_free on the range that includes the PTE. It would
clear the dirty-bit. It batches TLB flushes.
CPU2: Writes 4 to /proc/PID/clear_refs , clearing the PTEs soft-dirty.
We care about the fact that it clears the PTE write-bit, and of
course, batches TLB flushes.
CPU3: Runs KSM. Our purpose is to pass the following test in
write_protect_page():
if (pte_write(*pvmw.pte) || pte_dirty(*pvmw.pte) ||
(pte_protnone(*pvmw.pte) && pte_savedwrite(*pvmw.pte)))
Since it will avoid TLB flush. And we want to do it while the PTE is
stale. Later, and before replacing the page, we would be able to
change the page.
Note that all the operations the CPU1-3 perform canhappen in parallel
since they only acquire mmap_sem for read.
We start with two identical pages. Everything below regards the same
page/PTE.
CPU0 CPU1 CPU2 CPU3
---- ---- ---- ----
Write the same
value on page
[cache PTE as
dirty in TLB]
MADV_FREE
pte_mkclean()
4 > clear_refs
pte_wrprotect()
write_protect_page()
[ success, no flush ]
pages_indentical()
[ ok ]
Write to page
different value
[Ok, using stale
PTE]
replace_page()
Later, CPU1, CPU2 and CPU3 would flush the TLB, but that is too late.
CPU0 already wrote on the page, but KSM ignored this write, and it got
lost"
In above scenario, MADV_FREE is fixed by changing TLB batching API
including [set|clear]_tlb_flush_pending. Remained thing is soft-dirty
part.
This patch changes soft-dirty uses TLB batching API instead of
flush_tlb_mm and KSM checks pending TLB flush by using
mm_tlb_flush_pending so that it will flush TLB to avoid data lost if
there are other parallel threads pending TLB flush.
Minchan Kim [Thu, 10 Aug 2017 22:24:12 +0000 (15:24 -0700)]
mm: fix MADV_[FREE|DONTNEED] TLB flush miss problem
Nadav reported parallel MADV_DONTNEED on same range has a stale TLB
problem and Mel fixed it[1] and found same problem on MADV_FREE[2].
Quote from Mel Gorman:
"The race in question is CPU 0 running madv_free and updating some PTEs
while CPU 1 is also running madv_free and looking at the same PTEs.
CPU 1 may have writable TLB entries for a page but fail the pte_dirty
check (because CPU 0 has updated it already) and potentially fail to
flush.
Hence, when madv_free on CPU 1 returns, there are still potentially
writable TLB entries and the underlying PTE is still present so that a
subsequent write does not necessarily propagate the dirty bit to the
underlying PTE any more. Reclaim at some unknown time at the future
may then see that the PTE is still clean and discard the page even
though a write has happened in the meantime. I think this is possible
but I could have missed some protection in madv_free that prevents it
happening."
This patch aims for solving both problems all at once and is ready for
other problem with KSM, MADV_FREE and soft-dirty story[3].
TLB batch API(tlb_[gather|finish]_mmu] uses [inc|dec]_tlb_flush_pending
and mmu_tlb_flush_pending so that when tlb_finish_mmu is called, we can
catch there are parallel threads going on. In that case, forcefully,
flush TLB to prevent for user to access memory via stale TLB entry
although it fail to gather page table entry.
I confirmed this patch works with [4] test program Nadav gave so this
patch supersedes "mm: Always flush VMA ranges affected by zap_page_range
v2" in current mmotm.
NOTE:
This patch modifies arch-specific TLB gathering interface(x86, ia64,
s390, sh, um). It seems most of architecture are straightforward but
s390 need to be careful because tlb_flush_mmu works only if
mm->context.flush_mm is set to non-zero which happens only a pte entry
really is cleared by ptep_get_and_clear and friends. However, this
problem never changes the pte entries but need to flush to prevent
memory access from stale tlb.
Minchan Kim [Thu, 10 Aug 2017 22:24:09 +0000 (15:24 -0700)]
mm: make tlb_flush_pending global
Currently, tlb_flush_pending is used only for CONFIG_[NUMA_BALANCING|
COMPACTION] but upcoming patches to solve subtle TLB flush batching
problem will use it regardless of compaction/NUMA so this patch doesn't
remove the dependency.
[akpm@linux-foundation.org: remove more ifdefs from world's ugliest printk statement] Link: http://lkml.kernel.org/r/20170802000818.4760-6-namit@vmware.com Signed-off-by: Minchan Kim <minchan@kernel.org> Signed-off-by: Nadav Amit <namit@vmware.com> Acked-by: Mel Gorman <mgorman@techsingularity.net> Cc: "David S. Miller" <davem@davemloft.net> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Hugh Dickins <hughd@google.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Jeff Dike <jdike@addtoit.com> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Mel Gorman <mgorman@suse.de> Cc: Nadav Amit <nadav.amit@gmail.com> Cc: Rik van Riel <riel@redhat.com> Cc: Russell King <linux@armlinux.org.uk> Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Cc: Tony Luck <tony.luck@intel.com> Cc: Yoshinori Sato <ysato@users.sourceforge.jp> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Minchan Kim [Thu, 10 Aug 2017 22:24:05 +0000 (15:24 -0700)]
mm: refactor TLB gathering API
This patch is a preparatory patch for solving race problems caused by
TLB batch. For that, we will increase/decrease TLB flush pending count
of mm_struct whenever tlb_[gather|finish]_mmu is called.
Before making it simple, this patch separates architecture specific part
and rename it to arch_tlb_[gather|finish]_mmu and generic part just
calls it.
It shouldn't change any behavior.
Link: http://lkml.kernel.org/r/20170802000818.4760-5-namit@vmware.com Signed-off-by: Minchan Kim <minchan@kernel.org> Signed-off-by: Nadav Amit <namit@vmware.com> Acked-by: Mel Gorman <mgorman@techsingularity.net> Cc: Ingo Molnar <mingo@redhat.com> Cc: Russell King <linux@armlinux.org.uk> Cc: Tony Luck <tony.luck@intel.com> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Yoshinori Sato <ysato@users.sourceforge.jp> Cc: Jeff Dike <jdike@addtoit.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Hugh Dickins <hughd@google.com> Cc: Mel Gorman <mgorman@suse.de> Cc: Nadav Amit <nadav.amit@gmail.com> Cc: Rik van Riel <riel@redhat.com> Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nadav Amit [Thu, 10 Aug 2017 22:24:02 +0000 (15:24 -0700)]
Revert "mm: numa: defer TLB flush for THP migration as long as possible"
While deferring TLB flushes is a good practice, the reverted patch
caused pending TLB flushes to be checked while the page-table lock is
not taken. As a result, in architectures with weak memory model (PPC),
Linux may miss a memory-barrier, miss the fact TLB flushes are pending,
and cause (in theory) a memory corruption.
Since the alternative of using smp_mb__after_unlock_lock() was
considered a bit open-coded, and the performance impact is expected to
be small, the previous patch is reverted.
This reverts b0943d61b8fa ("mm: numa: defer TLB flush for THP migration
as long as possible").
Link: http://lkml.kernel.org/r/20170802000818.4760-4-namit@vmware.com Signed-off-by: Nadav Amit <namit@vmware.com> Suggested-by: Mel Gorman <mgorman@suse.de> Acked-by: Mel Gorman <mgorman@suse.de> Acked-by: Rik van Riel <riel@redhat.com> Cc: Minchan Kim <minchan@kernel.org> Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Hugh Dickins <hughd@google.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Jeff Dike <jdike@addtoit.com> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Mel Gorman <mgorman@techsingularity.net> Cc: Nadav Amit <nadav.amit@gmail.com> Cc: Russell King <linux@armlinux.org.uk> Cc: Tony Luck <tony.luck@intel.com> Cc: Yoshinori Sato <ysato@users.sourceforge.jp> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nadav Amit [Thu, 10 Aug 2017 22:23:59 +0000 (15:23 -0700)]
mm: migrate: fix barriers around tlb_flush_pending
Reading tlb_flush_pending while the page-table lock is taken does not
require a barrier, since the lock/unlock already acts as a barrier.
Removing the barrier in mm_tlb_flush_pending() to address this issue.
However, migrate_misplaced_transhuge_page() calls mm_tlb_flush_pending()
while the page-table lock is already released, which may present a
problem on architectures with weak memory model (PPC). To deal with
this case, a new parameter is added to mm_tlb_flush_pending() to
indicate if it is read without the page-table lock taken, and calling
smp_mb__after_unlock_lock() in this case.
Link: http://lkml.kernel.org/r/20170802000818.4760-3-namit@vmware.com Signed-off-by: Nadav Amit <namit@vmware.com> Acked-by: Rik van Riel <riel@redhat.com> Cc: Minchan Kim <minchan@kernel.org> Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Mel Gorman <mgorman@suse.de> Cc: "David S. Miller" <davem@davemloft.net> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Hugh Dickins <hughd@google.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Jeff Dike <jdike@addtoit.com> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Mel Gorman <mgorman@techsingularity.net> Cc: Nadav Amit <nadav.amit@gmail.com> Cc: Russell King <linux@armlinux.org.uk> Cc: Tony Luck <tony.luck@intel.com> Cc: Yoshinori Sato <ysato@users.sourceforge.jp> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nadav Amit [Thu, 10 Aug 2017 22:23:56 +0000 (15:23 -0700)]
mm: migrate: prevent racy access to tlb_flush_pending
Patch series "fixes of TLB batching races", v6.
It turns out that Linux TLB batching mechanism suffers from various
races. Races that are caused due to batching during reclamation were
recently handled by Mel and this patch-set deals with others. The more
fundamental issue is that concurrent updates of the page-tables allow
for TLB flushes to be batched on one core, while another core changes
the page-tables. This other core may assume a PTE change does not
require a flush based on the updated PTE value, while it is unaware that
TLB flushes are still pending.
This behavior affects KSM (which may result in memory corruption) and
MADV_FREE and MADV_DONTNEED (which may result in incorrect behavior). A
proof-of-concept can easily produce the wrong behavior of MADV_DONTNEED.
Memory corruption in KSM is harder to produce in practice, but was
observed by hacking the kernel and adding a delay before flushing and
replacing the KSM page.
Finally, there is also one memory barrier missing, which may affect
architectures with weak memory model.
This patch (of 7):
Setting and clearing mm->tlb_flush_pending can be performed by multiple
threads, since mmap_sem may only be acquired for read in
task_numa_work(). If this happens, tlb_flush_pending might be cleared
while one of the threads still changes PTEs and batches TLB flushes.
This can lead to the same race between migration and
change_protection_range() that led to the introduction of
tlb_flush_pending. The result of this race was data corruption, which
means that this patch also addresses a theoretically possible data
corruption.
An actual data corruption was not observed, yet the race was was
confirmed by adding assertion to check tlb_flush_pending is not set by
two threads, adding artificial latency in change_protection_range() and
using sysctl to reduce kernel.numa_balancing_scan_delay_ms.
Link: http://lkml.kernel.org/r/20170802000818.4760-2-namit@vmware.com Fixes: 20841405940e ("mm: fix TLB flush race between migration, and
change_protection_range") Signed-off-by: Nadav Amit <namit@vmware.com> Acked-by: Mel Gorman <mgorman@suse.de> Acked-by: Rik van Riel <riel@redhat.com> Acked-by: Minchan Kim <minchan@kernel.org> Cc: Andy Lutomirski <luto@kernel.org> Cc: Hugh Dickins <hughd@google.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Jeff Dike <jdike@addtoit.com> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Mel Gorman <mgorman@techsingularity.net> Cc: Russell King <linux@armlinux.org.uk> Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Cc: Tony Luck <tony.luck@intel.com> Cc: Yoshinori Sato <ysato@users.sourceforge.jp> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Akinobu Mita [Thu, 10 Aug 2017 22:23:53 +0000 (15:23 -0700)]
fault-inject: fix wrong should_fail() decision in task context
Commit 1203c8e6fb0a ("fault-inject: simplify access check for fail-nth")
unintentionally broke a conditional statement in should_fail(). Any
faults are not injected in the task context by the change when the
systematic fault injection is not used.
This change restores to the previous correct behaviour.
Link: http://lkml.kernel.org/r/1501633700-3488-1-git-send-email-akinobu.mita@gmail.com Fixes: 1203c8e6fb0a ("fault-inject: simplify access check for fail-nth") Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Reported-by: Lu Fengqi <lufq.fnst@cn.fujitsu.com> Tested-by: Lu Fengqi <lufq.fnst@cn.fujitsu.com> Cc: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dan Carpenter [Thu, 10 Aug 2017 22:23:50 +0000 (15:23 -0700)]
test_kmod: fix small memory leak on filesystem tests
The break was in the wrong place so file system tests don't work as
intended, leaking memory at each test switch.
[mcgrof@kernel.org: massaged commit subject, noted memory leak issue without the fix] Link: http://lkml.kernel.org/r/20170802211450.27928-6-mcgrof@kernel.org Fixes: 39258f448d71 ("kmod: add test driver to stress test the module loader") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org> Reported-by: David Binderman <dcb314@hotmail.com> Cc: Colin Ian King <colin.king@canonical.com> Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com> Cc: Eric W. Biederman <ebiederm@xmission.com> Cc: Jessica Yu <jeyu@redhat.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Kees Cook <keescook@chromium.org> Cc: Michal Marek <mmarek@suse.com> Cc: Miroslav Benes <mbenes@suse.cz> Cc: Petr Mladek <pmladek@suse.com> Cc: Rusty Russell <rusty@rustcorp.com.au> Cc: Shuah Khan <shuah@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dan Carpenter [Thu, 10 Aug 2017 22:23:47 +0000 (15:23 -0700)]
test_kmod: fix the lock in register_test_dev_kmod()
We accidentally just drop the lock twice instead of taking it and then
releasing it. This isn't a big issue unless you are adding more than
one device to test on, and the kmod.sh doesn't do that yet, however this
obviously is the correct thing to do.
[mcgrof@kernel.org: massaged subject, explain what happens] Link: http://lkml.kernel.org/r/20170802211450.27928-5-mcgrof@kernel.org Fixes: 39258f448d71 ("kmod: add test driver to stress test the module loader") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org> Cc: Colin Ian King <colin.king@canonical.com> Cc: David Binderman <dcb314@hotmail.com> Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com> Cc: Eric W. Biederman <ebiederm@xmission.com> Cc: Jessica Yu <jeyu@redhat.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Kees Cook <keescook@chromium.org> Cc: Michal Marek <mmarek@suse.com> Cc: Miroslav Benes <mbenes@suse.cz> Cc: Petr Mladek <pmladek@suse.com> Cc: Rusty Russell <rusty@rustcorp.com.au> Cc: Shuah Khan <shuah@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
test_kmod: fix bug which allows negative values on two config options
Parsing with kstrtol() enables values to be negative, and we failed to
check for negative values when parsing with test_dev_config_update_uint_sync()
or test_dev_config_update_uint_range().
test_dev_config_update_uint_range() has a minimum check though so an
issue is not present there. test_dev_config_update_uint_sync() is only
used for the number of threads to use (config_num_threads_store()), and
indeed this would fail with an attempt for a large allocation.
Although the issue is only present in practice with the first fix both
by using kstrtoul() instead of kstrtol().
Link: http://lkml.kernel.org/r/20170802211450.27928-4-mcgrof@kernel.org Fixes: 39258f448d71 ("kmod: add test driver to stress test the module loader") Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org> Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Cc: Colin Ian King <colin.king@canonical.com> Cc: David Binderman <dcb314@hotmail.com> Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com> Cc: Eric W. Biederman <ebiederm@xmission.com> Cc: Jessica Yu <jeyu@redhat.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Kees Cook <keescook@chromium.org> Cc: Michal Marek <mmarek@suse.com> Cc: Miroslav Benes <mbenes@suse.cz> Cc: Petr Mladek <pmladek@suse.com> Cc: Rusty Russell <rusty@rustcorp.com.au> Cc: Shuah Khan <shuah@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[mcgrof@kernel.org: massaged commit message] Link: http://lkml.kernel.org/r/20170802211450.27928-3-mcgrof@kernel.org Fixes: 39258f448d71 ("kmod: add test driver to stress test the module loader") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org> Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com> Cc: Kees Cook <keescook@chromium.org> Cc: Jessica Yu <jeyu@redhat.com> Cc: Rusty Russell <rusty@rustcorp.com.au> Cc: Michal Marek <mmarek@suse.com> Cc: Petr Mladek <pmladek@suse.com> Cc: Miroslav Benes <mbenes@suse.cz> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Eric W. Biederman <ebiederm@xmission.com> Cc: Shuah Khan <shuah@kernel.org> Cc: Dan Carpenter <dan.carpenter@oracle.com> Cc: David Binderman <dcb314@hotmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrea Arcangeli [Thu, 10 Aug 2017 22:23:38 +0000 (15:23 -0700)]
userfaultfd: hugetlbfs: remove superfluous page unlock in VM_SHARED case
huge_add_to_page_cache->add_to_page_cache implicitly unlocks the page
before returning in case of errors.
The error returned was -EEXIST by running UFFDIO_COPY on a non-hole
offset of a VM_SHARED hugetlbfs mapping. It was an userland bug that
triggered it and the kernel must cope with it returning -EEXIST from
ioctl(UFFDIO_COPY) as expected.
Jonathan Toppins [Thu, 10 Aug 2017 22:23:35 +0000 (15:23 -0700)]
mm: ratelimit PFNs busy info message
The RDMA subsystem can generate several thousand of these messages per
second eventually leading to a kernel crash. Ratelimit these messages
to prevent this crash.
Doug said:
"I've been carrying a version of this for several kernel versions. I
don't remember when they started, but we have one (and only one) class
of machines: Dell PE R730xd, that generate these errors. When it
happens, without a rate limit, we get rcu timeouts and kernel oopses.
With the rate limit, we just get a lot of annoying kernel messages but
the machine continues on, recovers, and eventually the memory
operations all succeed"
And:
"> Well... why are all these EBUSY's occurring? It sounds inefficient
> (at least) but if it is expected, normal and unavoidable then
> perhaps we should just remove that message altogether?
I don't have an answer to that question. To be honest, I haven't
looked real hard. We never had this at all, then it started out of the
blue, but only on our Dell 730xd machines (and it hits all of them),
but no other classes or brands of machines. And we have our 730xd
machines loaded up with different brands and models of cards (for
instance one dedicated to mlx4 hardware, one for qib, one for mlx5, an
ocrdma/cxgb4 combo, etc), so the fact that it hit all of the machines
meant it wasn't tied to any particular brand/model of RDMA hardware.
To me, it always smelled of a hardware oddity specific to maybe the
CPUs or mainboard chipsets in these machines, so given that I'm not an
mm expert anyway, I never chased it down.
A few other relevant details: it showed up somewhere around 4.8/4.9 or
thereabouts. It never happened before, but the prinkt has been there
since the 3.18 days, so possibly the test to trigger this message was
changed, or something else in the allocator changed such that the
situation started happening on these machines?
And, like I said, it is specific to our 730xd machines (but they are
all identical, so that could mean it's something like their specific
ram configuration is causing the allocator to hit this on these
machine but not on other machines in the cluster, I don't want to say
it's necessarily the model of chipset or CPU, there are other bits of
identicalness between these machines)"
Johannes Weiner [Thu, 10 Aug 2017 22:23:31 +0000 (15:23 -0700)]
mm: fix global NR_SLAB_.*CLAIMABLE counter reads
As Tetsuo points out:
"Commit 385386cff4c6 ("mm: vmstat: move slab statistics from zone to
node counters") broke "Slab:" field of /proc/meminfo . It shows nearly
0kB"
In addition to /proc/meminfo, this problem also affects the slab
counters OOM/allocation failure info dumps, can cause early -ENOMEM from
overcommit protection, and miscalculate image size requirements during
suspend-to-disk.
This is because the patch in question switched the slab counters from
the zone level to the node level, but forgot to update the global
accessor functions to read the aggregate node data instead of the
aggregate zone data.
Use global_node_page_state() to access the global slab counters.
Fixes: 385386cff4c6 ("mm: vmstat: move slab statistics from zone to node counters") Link: http://lkml.kernel.org/r/20170801134256.5400-1-hannes@cmpxchg.org Signed-off-by: Johannes Weiner <hannes@cmpxchg.org> Reported-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp> Acked-by: Michal Hocko <mhocko@suse.com> Cc: Josef Bacik <josef@toxicpanda.com> Cc: Vladimir Davydov <vdavydov.dev@gmail.com> Cc: Stefan Agner <stefan@agner.ch> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 10 Aug 2017 21:52:45 +0000 (14:52 -0700)]
Merge tag 'pci-v4.13-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fix from Bjorn Helgaas:
"Work around Renesas uPD72020x 32-bit DMA issue"
* tag 'pci-v4.13-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
xhci: Reset Renesas uPD72020x USB controller for 32-bit DMA issue
PCI: Add pci_reset_function_locked()
Mika Westerberg [Tue, 25 Jul 2017 14:41:58 +0000 (17:41 +0300)]
thunderbolt: Do not enumerate more ports from DROM than the controller has
Some Alpine Ridge LP DROMs (there might be others) erroneusly list more
ports than the controller actually has. Most probably because DROM of
the full Dual/Single port Thunderbolt controller was reused for LP
version. The current DROM parser does not check the upper bound thus it
leads to crash when sw->ports[] is accessed over bounds:
mei: exclude device from suspend direct complete optimization
MEI device performs link reset during system suspend sequence.
The link reset cannot be performed while device is in
runtime suspend state. The resume sequence is bypassed with
suspend direct complete optimization,so the optimization should be
disabled for mei devices.
Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Reported-by: Dominik Brodowski <linux@dominikbrodowski.net> Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Cc: Dominik Brodowski <linux@dominikbrodowski.net> Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
firmware: avoid invalid fallback aborts by using killable wait
Commit 0cb64249ca500 ("firmware_loader: abort request if wait_for_completion
is interrupted") added via 4.0 added support to abort the fallback mechanism
when a signal was detected and wait_for_completion_interruptible() returned
-ERESTARTSYS -- for instance when a user hits CTRL-C. The abort was overly
*too* effective.
When a child process terminates (successful or not) the signal SIGCHLD can
be sent to the parent process which ran the child in the background and
later triggered a sync request for firmware through a sysfs interface which
relies on the fallback mechanism. This signal in turn can be recieved by the
interruptible wait we constructed on firmware_class and detects it as an
abort *before* userspace could get a chance to write the firmware. Upon
failure -EAGAIN is returned, so userspace is also kept in the dark about
exactly what happened.
We can reproduce the issue with the fw_fallback.sh selftest:
Before this patch:
$ sudo tools/testing/selftests/firmware/fw_fallback.sh
...
tools/testing/selftests/firmware/fw_fallback.sh: error - sync firmware request cancelled due to SIGCHLD
After this patch:
$ sudo tools/testing/selftests/firmware/fw_fallback.sh
...
tools/testing/selftests/firmware/fw_fallback.sh: SIGCHLD on sync ignored as expected
Fix this by making the wait killable -- only killable by SIGKILL (kill -9).
We loose the ability to allow userspace to cancel a write with CTRL-C
(SIGINT), however its been decided the compromise to require SIGKILL is
worth the gains.
Chances of this issue occuring are low due to the number of drivers upstream
exclusively relying on the fallback mechanism for firmware (2 drivers),
however this is observed in the field with custom drivers with sysfs
triggers to load firmware. Only distributions relying on the fallback
mechanism are impacted as well. An example reported issue was on Android,
as follows:
1) Android init (pid=1) fork()s (say pid=42) [this child process is totally
unrelated to firmware loading, it could be sleep 2; for all we care ]
2) Android init (pid=1) does a write() on a (driver custom) sysfs file which
ends up calling request_firmware() kernel side
3) The firmware loading fallback mechanism is used, the request is sent to
userspace and pid 1 waits in the kernel on wait_*
4) before firmware loading completes pid 42 dies (for any reason, even
normal termination)
5) Kernel delivers SIGCHLD to pid=1 to tell it a child has died, which
causes -ERESTARTSYS to be returned from wait_*
6) The kernel's wait aborts and return -EAGAIN for the
request_firmware() caller.
Cc: stable <stable@vger.kernel.org> # 4.0 Fixes: 0cb64249ca500 ("firmware_loader: abort request if wait_for_completion is interrupted") Suggested-by: "Eric W. Biederman" <ebiederm@xmission.com> Suggested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Tested-by: Martin Fuzzey <mfuzzey@parkeon.com> Reported-by: Martin Fuzzey <mfuzzey@parkeon.com> Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
firmware: fix batched requests - send wake up on failure on direct lookups
Fix batched requests from waiting forever on failure.
The firmware API batched requests feature has been broken since the API call
request_firmware_direct() was introduced on commit bba3a87e982ad ("firmware:
Introduce request_firmware_direct()"), added on v3.14 *iff* the firmware
being requested was not present in *certain kernel builds* [0].
When no firmware is found the worker which goes on to finish never informs
waiters queued up of this, so any batched request will stall in what seems
to be forever (MAX_SCHEDULE_TIMEOUT). Sadly, a reboot will also stall, as
the reboot notifier was only designed to kill custom fallback workers. The
issue seems to the user as a type of soft lockup, what *actually* happens
underneath the hood is a wait call which never completes as we failed to
issue a completion on error.
For device drivers with optional firmware schemes (ie, Intel iwlwifi, or
Netronome -- even though it uses request_firmware() and not
request_firmware_direct()), this could mean that when you boot a system with
multiple cards the firmware will seem to never load on the system, or that
the card is just not responsive even the driver initialization. Due to
differences in scheduling possible this should not always trigger --
one would need to to ensure that multiple requests are in place at the
right time for this to work, also release_firmware() must not be called
prior to any other incoming request. The complexity may not be worth
supporting batched requests in the future given the wait mechanism is
only used also for the fallback mechanism. We'll keep it for now and
just fix it.
Its reported that at least with the Intel WiFi cards on one system this
issue was creeping up 50% of the boots [0].
Before this commit batched requests testing revealed:
============================================================================
CONFIG_FW_LOADER_USER_HELPER_FALLBACK=n
CONFIG_FW_LOADER_USER_HELPER=y
Most common Linux distribution setup.
API-type no-firmware-found firmware-found
----------------------------------------------------------------------
request_firmware() FAIL OK
request_firmware_direct() FAIL OK
request_firmware_nowait(uevent=true) FAIL OK
request_firmware_nowait(uevent=false) FAIL OK
============================================================================
CONFIG_FW_LOADER_USER_HELPER_FALLBACK=n
CONFIG_FW_LOADER_USER_HELPER=n
Only possible if CONFIG_DELL_RBU=n and CONFIG_LEDS_LP55XX_COMMON=n, rare.
API-type no-firmware-found firmware-found
----------------------------------------------------------------------
request_firmware() FAIL OK
request_firmware_direct() FAIL OK
request_firmware_nowait(uevent=true) FAIL OK
request_firmware_nowait(uevent=false) FAIL OK
============================================================================
CONFIG_FW_LOADER_USER_HELPER_FALLBACK=y
CONFIG_FW_LOADER_USER_HELPER=y
Google Android setup.
API-type no-firmware-found firmware-found
----------------------------------------------------------------------
request_firmware() OK OK
request_firmware_direct() FAIL OK
request_firmware_nowait(uevent=true) OK OK
request_firmware_nowait(uevent=false) OK OK
============================================================================
Ater this commit batched testing results:
============================================================================
CONFIG_FW_LOADER_USER_HELPER_FALLBACK=n
CONFIG_FW_LOADER_USER_HELPER=y
Most common Linux distribution setup.
API-type no-firmware-found firmware-found
----------------------------------------------------------------------
request_firmware() OK OK
request_firmware_direct() OK OK
request_firmware_nowait(uevent=true) OK OK
request_firmware_nowait(uevent=false) OK OK
============================================================================
CONFIG_FW_LOADER_USER_HELPER_FALLBACK=n
CONFIG_FW_LOADER_USER_HELPER=n
Only possible if CONFIG_DELL_RBU=n and CONFIG_LEDS_LP55XX_COMMON=n, rare.
API-type no-firmware-found firmware-found
----------------------------------------------------------------------
request_firmware() OK OK
request_firmware_direct() OK OK
request_firmware_nowait(uevent=true) OK OK
request_firmware_nowait(uevent=false) OK OK
============================================================================
CONFIG_FW_LOADER_USER_HELPER_FALLBACK=y
CONFIG_FW_LOADER_USER_HELPER=y
Google Android setup.
API-type no-firmware-found firmware-found
----------------------------------------------------------------------
request_firmware() OK OK
request_firmware_direct() OK OK
request_firmware_nowait(uevent=true) OK OK
request_firmware_nowait(uevent=false) OK OK
============================================================================
The firmware cache mechanism serves two purposes, the secondary purpose is
not well documented nor understood. This fixes a regression with the
secondary purpose of the firmware cache mechanism: batched requests on
successful lookups. Without this fix *any* time a batched request is
triggered, secondary requests for which the batched request mechanism
was designed for will seem to last forver and seem to never return.
This issue is present for all kernel builds possible, and a hard reset
is required.
The firmware cache is used for:
1) Addressing races with file lookups during the suspend/resume cycle
by keeping firmware in memory during the suspend/resume cycle
2) Batched requests for the same file rely only on work from the first file
lookup, which keeps the firmware in memory until the last
release_firmware() is called
Batched requests *only* take effect if secondary requests come in prior to
the first user calling release_firmware(). The devres name used for the
internal firmware cache is used as a hint other pending requests are
ongoing, the firmware buffer data is kept in memory until the last user of
the buffer calls release_firmware(), therefore serializing requests and
delaying the release until all requests are done.
Batched requests wait for a wakup or signal so we can rely on the first file
fetch to write to the pending secondary requests. Commit 5b029624948d
("firmware: do not use fw_lock for fw_state protection") ported the firmware
API to use swait, and in doing so failed to convert complete_all() to
swake_up_all() -- it used swake_up(), loosing the ability for *some* batched
requests to take effect.
We *could* fix this by just using swake_up_all() *but* swait is now known
to be very special use case, so its best to just move away from it. So we
just go back to using completions as before commit 5b029624948d ("firmware:
do not use fw_lock for fw_state protection") given this was using
complete_all().
Without this fix it has been reported plugging in two Intel 6260 Wifi cards
on a system will end up enumerating the two devices only 50% of the time
[0]. The ported swake_up() should have actually handled the case with two
devices, however, *if more than two cards are used* the swake_up() would
not have sufficed. This change is only part of the required fixes for
batched requests. Another fix is provided in the next patch.
This particular change should fix the cases where more than three requests
with the same firmware name is used, otherwise batched requests will wait
for MAX_SCHEDULE_TIMEOUT and just timeout eventually.
Below is a summary of tests triggering batched requests on different
kernel builds.
Before this patch:
============================================================================
CONFIG_FW_LOADER_USER_HELPER_FALLBACK=n
CONFIG_FW_LOADER_USER_HELPER=y
After this patch:
============================================================================
CONFIG_FW_LOADER_USER_HELPER_FALLBACK=n
CONFIG_FW_LOADER_USER_HELPER=y
Most common Linux distribution setup.
API-type no-firmware-found firmware-found
----------------------------------------------------------------------
request_firmware() FAIL OK
request_firmware_direct() FAIL OK
request_firmware_nowait(uevent=true) FAIL OK
request_firmware_nowait(uevent=false) FAIL OK
============================================================================
CONFIG_FW_LOADER_USER_HELPER_FALLBACK=n
CONFIG_FW_LOADER_USER_HELPER=n
Only possible if CONFIG_DELL_RBU=n and CONFIG_LEDS_LP55XX_COMMON=n, rare.
API-type no-firmware-found firmware-found
----------------------------------------------------------------------
request_firmware() FAIL OK
request_firmware_direct() FAIL OK
request_firmware_nowait(uevent=true) FAIL OK
request_firmware_nowait(uevent=false) FAIL OK
============================================================================
CONFIG_FW_LOADER_USER_HELPER_FALLBACK=y
CONFIG_FW_LOADER_USER_HELPER=y
Google Android setup.
API-type no-firmware-found firmware-found
----------------------------------------------------------------------
request_firmware() OK OK
request_firmware_direct() FAIL OK
request_firmware_nowait(uevent=true) OK OK
request_firmware_nowait(uevent=false) OK OK
============================================================================
CC: <stable@vger.kernel.org> [4.10+] Cc: Ming Lei <ming.lei@redhat.com> Fixes: 5b029624948d ("firmware: do not use fw_lock for fw_state protection") Reported-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds a new ATEN device id for a new pl2303-based device.
Reported-by: Peter Kuo <PeterKuo@aten.com.tw> Cc: stable <stable@vger.kernel.org> Cc: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alan Stern [Tue, 1 Aug 2017 14:41:56 +0000 (10:41 -0400)]
USB: Check for dropped connection before switching to full speed
Some buggy USB disk adapters disconnect and reconnect multiple times
during the enumeration procedure. This may lead to a device
connecting at full speed instead of high speed, because when the USB
stack sees that a device isn't able to enumerate at high speed, it
tries to hand the connection over to a full-speed companion
controller.
The logic for doing this is careful to check that the device is still
connected. But this check is inadequate if the device disconnects and
reconnects before the check is done. The symptom is that a device
works, but much more slowly than it is capable of operating.
The situation was made worse recently by commit 22547c4cc4fe ("usb:
hub: Wait for connection to be reestablished after port reset"), which
increases the delay following a reset before a disconnect is
recognized, thus giving the device more time to reconnect.
This patch makes the check more robust. If the device was
disconnected at any time during enumeration, we will now skip the
full-speed handover.
Sandeep Singh [Fri, 4 Aug 2017 11:05:56 +0000 (16:35 +0530)]
usb:xhci:Add quirk for Certain failing HP keyboard on reset after resume
Certain HP keyboards would keep inputting a character automatically which
is the wake-up key after S3 resume
On some AMD platforms USB host fails to respond (by holding resume-K) to
USB device (an HP keyboard) resume request within 1ms (TURSM) and ensures
that resume is signaled for at least 20 ms (TDRSMDN), which is defined in
USB 2.0 spec. The result is that the keyboard is out of function.
In SNPS USB design, the host responds to the resume request only after
system gets back to S0 and the host gets to functional after the internal
HW restore operation that is more than 1 second after the initial resume
request from the USB device.
As a workaround for specific keyboard ID(HP Keyboards), applying port reset
after resume when the keyboard is plugged in.
Signed-off-by: Sandeep Singh <Sandeep.Singh@amd.com> Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
cc: Nehal Shah <Nehal-bakulchandra.Shah@amd.com> Reviewed-by: Felipe Balbi <felipe.balbi@linux.intel.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Keith Busch [Thu, 10 Aug 2017 09:23:31 +0000 (11:23 +0200)]
nvme: fix nvme reset command timeout handling
We need to return an error if a timeout occurs on any NVMe command during
initialization. Without this, the nvme reset work will be stuck. A timeout
will have a negative error code, meaning we need to stop initializing
the controller. All postitive returns mean the controller is still usable.
Signed-off-by: Keith Busch <keith.busch@intel.com> Cc: Martin Peres <martin.peres@intel.com>
[jth consolidated cleanup path ] Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Christoph Hellwig <hch@lst.de>
1) Fix handling of initial STATE message in TIPC, from Jon Paul Maloy.
2) Fix stats handling in bcm_sysport_get_stats(), from Florian
Fainelli.
3) Reject 16777215 VNI value in geneve_validate(), from Girish
Moodalbail.
4) Fix initial IGMP sysctl setting regression, from Nikolay Borisov.
5) Once a UFO fragmented frame is treated as UFO, we should continue
doing so. Likewise once a frame has been segmented, we should
continue doing that and not try to convert it to a UFO frame. From
Willem de Bruijn.
6) Test the AF_PACKET RX/TX ring pg_vec state under the socket lock to
prevent races. From Willem de Bruijn.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
packet: fix tp_reserve race in packet_set_ring
udp: consistently apply ufo or fragmentation
net: sched: set xt_tgchk_param par.nft_compat as 0 in ipt_init_target
igmp: Fix regression caused by igmp sysctl namespace code.
geneve: maximum value of VNI cannot be used
net: systemport: Fix software statistics for SYSTEMPORT Lite
tipc: remove premature ESTABLISH FSM event at link synchronization
Willem de Bruijn [Thu, 10 Aug 2017 16:41:58 +0000 (12:41 -0400)]
packet: fix tp_reserve race in packet_set_ring
Updates to tp_reserve can race with reads of the field in
packet_set_ring. Avoid this by holding the socket lock during
updates in setsockopt PACKET_RESERVE.
This bug was discovered by syzkaller.
Fixes: 8913336a7e8d ("packet: add PACKET_RESERVE sockopt") Reported-by: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Willem de Bruijn [Thu, 10 Aug 2017 16:29:19 +0000 (12:29 -0400)]
udp: consistently apply ufo or fragmentation
When iteratively building a UDP datagram with MSG_MORE and that
datagram exceeds MTU, consistently choose UFO or fragmentation.
Once skb_is_gso, always apply ufo. Conversely, once a datagram is
split across multiple skbs, do not consider ufo.
Sendpage already maintains the first invariant, only add the second.
IPv6 does not have a sendpage implementation to modify.
A gso skb must have a partial checksum, do not follow sk_no_check_tx
in udp_send_skb.
Found by syzkaller.
Fixes: e89e9cf539a2 ("[IPv4/IPv6]: UFO Scatter-gather approach") Reported-by: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
1) Recognize M8 cpus, just basic chip ID matching, from Allen Pais.
2) Prevent crashes when bringing up sunvdc virtual block devices in
some environments. From Jim Quigley.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sunvdc: prevent sunvdc panic when mpgroup disk added to guest domain
sparc64: Increase max_phys_bits to 51 and VA bits to 53 for M8.
sparc64: recognize and support sparc M8 cpu type
sparc64: properly name the cpu constants
Max Gurtovoy [Sat, 29 Jul 2017 22:45:08 +0000 (01:45 +0300)]
nvme-pci: fix CMB sysfs file removal in reset path
Currently we create the sysfs entry even if we fail mapping
it. In that case, the unmapping will not remove the sysfs created
file. There is no good reason to create a sysfs entry for a non
working CMB and show his characteristics.
Fixes: f63572dff ("nvme: unmap CMB and remove sysfs file in reset path") Signed-off-by: Max Gurtovoy <maxg@mellanox.com> Reviewed-by: Stephen Bates <sbates@raithlin.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
projects / mirror_ubuntu-bionic-kernel.git / log