Ariel Levkovich [Mon, 25 Jun 2018 16:12:02 +0000 (19:12 +0300)]
net/mlx5: Adjust clock overflow work period
When driver converts HW timestamp to wall clock time it subtracts
the last saved cycle counter from the HW timestamp and converts the
difference to nanoseconds.
The conversion is done by multiplying the cycles difference with the
clock multiplier value as a first step and therefore the cycles
difference should be small enough so that the multiplication product
doesn't exceed 64bit.
The overflow handling routine is in charge of updating the last saved
cycle counter in driver and it is called periodically using kernel
delayed workqueue.
The delay period for this work is calculated using the max HW cycle
counter value (a 41 bit mask) as a base which doesn't take the 64bit
limit into account so the delay period may be incorrect and too
long to prevent a large difference between the HW counter and the last
saved counter in SW.
This change adjusts the work period for the HW clock overflow work by
taking the minimum between the previous value and the quotient of max
u64 value and the clock multiplier value.
Shay Agroskin [Wed, 27 Jun 2018 12:43:07 +0000 (15:43 +0300)]
net/mlx5e: Refine ets validation function
Removed an error message received when configuring ETS total
bandwidth to be zero.
Our hardware doesn't support such configuration, so we shall
reject it in the driver. Nevertheless, we removed the error message
in order to eliminate error messages caused by old userspace tools
who try to pass such configuration.
Randy Dunlap [Wed, 18 Jul 2018 01:27:45 +0000 (18:27 -0700)]
tcp: identify cryptic messages as TCP seq # bugs
Attempt to make cryptic TCP seq number error messages clearer by
(1) identifying the source of the message as "TCP", (2) identifying the
errors as "seq # bug", and (3) grouping the field identifiers and values
by separating them with commas.
Suggested-by: 積丹尼 Dan Jacobson <jidanni@jidanni.org> Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
It seems that a *break* is missing in order to avoid falling through
to the default case. Otherwise, checking *chan* makes no sense.
Fixes: 72df7a7244c0 ("ptp: Allow reassigning calibration pin function") Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
hv_netvsc: Fix napi reschedule while receive completion is busy
If out ring is full temporarily and receive completion cannot go out,
we may still need to reschedule napi if certain conditions are met.
Otherwise the napi poll might be stopped forever, and cause network
disconnect.
Fixes: 7426b1a51803 ("netvsc: optimize receive completions") Signed-off-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The Vitaly Bordug's email bounces ("ru.mvista.com: Name or service not
known") and there was no activity (ack, review, sign) since 2009.
Cc: Vitaly Bordug <vitb@kernel.crashing.org> Cc: Pantelis Antoniou <pantelis.antoniou@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
net: cavium: Add fine-granular dependencies on PCI
Add dependencies on PCI where necessary.
Fixes: 7e2bc7fb65 ("net: cavium: Drop dependency of NET_VENDOR_CAVIUM on PCI") Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Stefan Wahren [Wed, 18 Jul 2018 06:31:44 +0000 (08:31 +0200)]
net: qca_spi: Make sure the QCA7000 reset is triggered
In case the SPI thread is not running, a simple reset of sync
state won't fix the transmit timeout. We also need to wake up the kernel
thread.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Fixes: ed7d42e24eff ("net: qca_spi: fix transmit queue timeout handling") Signed-off-by: David S. Miller <davem@davemloft.net>
Stefan Wahren [Wed, 18 Jul 2018 06:31:43 +0000 (08:31 +0200)]
net: qca_spi: Avoid packet drop during initial sync
As long as the synchronization with the QCA7000 isn't finished, we
cannot accept packets from the upper layers. So let the SPI thread
enable the TX queue after sync and avoid unwanted packet drop.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Fixes: 291ab06ecf67 ("net: qualcomm: new Ethernet over SPI driver for QCA7000") Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Tue, 17 Jul 2018 16:12:39 +0000 (17:12 +0100)]
ipv6: fix useless rol32 call on hash
The rol32 call is currently rotating hash but the rol'd value is
being discarded. I believe the current code is incorrect and hash
should be assigned the rotated value returned from rol32.
Thanks to David Lebrun for spotting this.
Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Tue, 17 Jul 2018 15:52:54 +0000 (16:52 +0100)]
ipv6: sr: fix useless rol32 call on hash
The rol32 call is currently rotating hash but the rol'd value is
being discarded. I believe the current code is incorrect and hash
should be assigned the rotated value returned from rol32.
Detected by CoverityScan, CID#1468411 ("Useless call")
Fixes: b5facfdba14c ("ipv6: sr: Compute flowlabel for outer IPv6 header of seg6 encap mode") Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: dlebrun@google.com Signed-off-by: David S. Miller <davem@davemloft.net>
net: usb: asix: replace mii_nway_restart in resume path
mii_nway_restart is not pm aware which results in a rtnl deadlock.
Implement mii_nway_restart manual by setting BMCR_ANRESTART if
BMCR_ANENABLE is set.
To reproduce:
* plug an asix based usb network interface
* wait until the device enters PM (~5 sec)
* `ip link set eth1 up` will never return
Fixes: d9fe64e51114 ("net: asix: Add in_pm parameter") Signed-off-by: Alexander Couzens <lynxis@fe80.eu> Signed-off-by: David S. Miller <davem@davemloft.net>
Fix this by sanitizing t.qset_idx before using it to index
adapter->msix_info
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
lib/rhashtable: consider param->min_size when setting initial table size
rhashtable_init() currently does not take into account the user-passed
min_size parameter unless param->nelem_hint is set as well. As such,
the default size (number of buckets) will always be HASH_DEFAULT_SIZE
even if the smallest allowed size is larger than that. Remediate this
by unconditionally calling into rounded_hashtable_size() and handling
things accordingly.
Signed-off-by: Davidlohr Bueso <dbueso@suse.de> Acked-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 18 Jul 2018 17:58:27 +0000 (10:58 -0700)]
Merge branch 'smc-fixes'
Ursula Braun says:
====================
net/smc: fixes 2018-07-18
here are small fixes for SMC: The first patch speeds up unidirectional
traffic, the second patch increases security, and the third patch
fixes a problem for fallback cases.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
During clc handshake the receive timeout is set to CLC_WAIT_TIME.
Remember and reset the original timeout value after the receive calls,
and remove a duplicate assignment of CLC_WAIT_TIME.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
For security reasons the return code of get_user() should always be
checked.
Fixes: 01d2f7e2cdd31 ("net/smc: sockopts TCP_NODELAY and TCP_CORK") Reported-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The SMC protocol requires to send a separate consumer cursor update,
if it cannot be piggybacked to updates of the producer cursor.
Currently the decision to send a separate consumer cursor update
just considers the amount of data already received by the socket
program. It does not consider the amount of data already arrived, but
not yet consumed by the receiver. Basing the decision on the
difference between already confirmed and already arrived data
(instead of difference between already confirmed and already consumed
data), may lead to a somewhat earlier consumer cursor update send in
fast unidirectional traffic scenarios, and thus to better throughput.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com> Suggested-by: Thomas Richter <tmricht@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/nfc: Avoid stalls when nfc_alloc_send_skb() returned NULL.
syzbot is reporting stalls at nfc_llcp_send_ui_frame() [1]. This is
because nfc_llcp_send_ui_frame() is retrying the loop without any delay
when nonblocking nfc_alloc_send_skb() returned NULL.
Since there is no need to use MSG_DONTWAIT if we retry until
sock_alloc_send_pskb() succeeds, let's use blocking call.
Also, in case an unexpected error occurred, let's break the loop
if blocking nfc_alloc_send_skb() failed.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Reported-by: syzbot <syzbot+d29d18215e477cfbfbdd@syzkaller.appspotmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
We almost never run into this by accident because randconfig builds
end up selecting DST_CACHE from some other tunnel protocol, and this
one appears to be the only one missing the explicit 'select'.
>From all I can tell, this problem first appeared in linux-4.9
when dst_cache support got added to ILA.
Fixes: 79ff2fc31e0f ("ila: Cache a route to translated address") Cc: Tom Herbert <tom@herbertland.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
octeon_mgmt: Fix MIX registers configuration on MTU setup
octeon_mgmt driver doesn't drop RX frames that are 1-4 bytes bigger than
MTU set for the corresponding interface. The problem is in the
AGL_GMX_RX0/1_FRM_MAX register setting, which should not account for VLAN
tagging.
According to Octeon HW manual:
"For tagged frames, MAX increases by four bytes for each VLAN found up to a
maximum of two VLANs, or MAX + 8 bytes."
OCTEON_FRAME_HEADER_LEN "define" is fine for ring buffer management, but
should not be used for AGL_GMX_RX0/1_FRM_MAX.
The problem could be easily reproduced using "ping" command. If affected
system has default MTU 1500, other host (having MTU >= 1504) can
successfully "ping" the affected system with payload size 1473-1476,
resulting in IP packets of size 1501-1504 accepted by the mgmt driver.
Fixed system still accepts IP packets of 1500 bytes even with VLAN tagging,
because the limits are lifted in HW as expected, for every VLAN tag.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
SMC ioctl processing requires the sock lock to work properly in
all thinkable scenarios.
Problem has been found with RaceFuzzer and fixes:
KASAN: null-ptr-deref Read in smc_ioctl
Reported-by: Byoungyoung Lee <lifeasageek@gmail.com> Reported-by: syzbot+35b2c5aa76fd398b9fd4@syzkaller.appspotmail.com Signed-off-by: Ursula Braun <ubraun@linux.ibm.com> Reviewed-by: Stefano Brivio <sbrivio@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch has fix for TX timeout while running bi-directional
traffic with 100 Mbps using 5762.
Signed-off-by: Sanjeev Bansal <sanjeevb.bansal@broadcom.com> Signed-off-by: Siva Reddy Kallam <siva.kallam@broadcom.com> Reviewed-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Siva Reddy Kallam <siva.kallam@broadcom.com> Reviewed-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
John Allen [Mon, 16 Jul 2018 15:29:30 +0000 (10:29 -0500)]
ibmvnic: Fix error recovery on login failure
Testing has uncovered a failure case that is not handled properly. In the
event that a login fails and we are not able to recover on the spot, we
return 0 from do_reset, preventing any error recovery code from being
triggered. Additionally, the state is set to "probed" meaning that when we
are able to trigger the error recovery, the driver always comes up in the
probed state. To handle the case properly, we need to return a failure code
here and set the adapter state to the state that we entered the reset in
indicating the state that we would like to come out of the recovery reset
in.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Stefan Wahren [Sun, 15 Jul 2018 19:53:20 +0000 (21:53 +0200)]
net: lan78xx: Fix race in tx pending skb size calculation
The skb size calculation in lan78xx_tx_bh is in race with the start_xmit,
which could lead to rare kernel oopses. So protect the whole skb walk with
a spin lock. As a benefit we can unlink the skb directly.
This patch was tested on Raspberry Pi 3B+
Link: https://github.com/raspberrypi/linux/issues/2608 Fixes: 55d7de9de6c3 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet") Cc: stable <stable@vger.kernel.org> Signed-off-by: Floris Bos <bos@je-eigen-domein.nl> Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Sun, 15 Jul 2018 16:35:19 +0000 (09:35 -0700)]
net/ipv6: Do not allow device only routes via the multipath API
Eric reported that reverting the patch that fixed and simplified IPv6
multipath routes means reverting back to invalid userspace notifications.
eg.,
$ ip -6 route add 2001:db8:1::/64 nexthop dev eth0 nexthop dev eth1
only generates a single notification:
2001:db8:1::/64 dev eth0 metric 1024 pref medium
While working on a fix for this problem I found another case that is just
broken completely - a multipath route with a gateway followed by device
followed by gateway:
$ ip -6 ro add 2001:db8:103::/64
nexthop via 2001:db8:1::64
nexthop dev dummy2
nexthop via 2001:db8:3::64
In this case the device only route is dropped completely - no notification
to userpsace but no addition to the FIB either:
$ ip -6 ro ls
2001:db8:1::/64 dev dummy1 proto kernel metric 256 pref medium
2001:db8:2::/64 dev dummy2 proto kernel metric 256 pref medium
2001:db8:3::/64 dev dummy3 proto kernel metric 256 pref medium
2001:db8:103::/64 metric 1024
nexthop via 2001:db8:1::64 dev dummy1 weight 1
nexthop via 2001:db8:3::64 dev dummy3 weight 1 pref medium
fe80::/64 dev dummy1 proto kernel metric 256 pref medium
fe80::/64 dev dummy2 proto kernel metric 256 pref medium
fe80::/64 dev dummy3 proto kernel metric 256 pref medium
Really, IPv6 multipath is just FUBAR'ed beyond repair when it comes to
device only routes, so do not allow it all.
This change will break any scripts relying on the mpath api for insert,
but I don't see any other way to handle the permutations. Besides, since
the routes are added to the FIB as standalone (non-multipath) routes the
kernel is not doing what the user requested, so it might as well tell the
user that.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David Ahern <dsahern@gmail.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Stefan Baranoff [Sun, 15 Jul 2018 15:36:37 +0000 (11:36 -0400)]
tcp: Fix broken repair socket window probe patch
Correct previous bad attempt at allowing sockets to come out of TCP
repair without sending window probes. To avoid changing size of
the repair variable in struct tcp_sock, this lets the decision for
sending probes or not to be made when coming out of repair by
introducing two ways to turn it off.
v2:
* Remove erroneous comment; defines now make behavior clear
Fixes: 70b7ff130224 ("tcp: allow user to create repair socket without window probes") Signed-off-by: Stefan Baranoff <sbaranoff@gmail.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Andrei Vagin <avagin@virtuozzo.com> Signed-off-by: David S. Miller <davem@davemloft.net>
When a new rx packet arrives, the rx path will decide whether to reuse
the remainder of the page or not according to one of the below conditions:
1. frag_info->frag_stride == PAGE_SIZE / 2
2. frags->page_offset + frag_info->frag_size > PAGE_SIZE;
The first condition is no met for when XDP is set.
For XDP, page_offset is always set to priv->rx_headroom which is
XDP_PACKET_HEADROOM and frag_info->frag_size is around mtu size + some
padding, still the 2nd release condition will hold since
XDP_PACKET_HEADROOM + 1536 < PAGE_SIZE, as a result the page will not
be released and will be _wrongly_ reused for next free rx descriptor.
In XDP there is an assumption to have a page per packet and reuse can
break such assumption and might cause packet data corruptions.
Fix this by adding an extra condition (!priv->rx_headroom) to the 2nd
case to avoid page reuse when XDP is set, since rx_headroom is set to 0
for non XDP setup and set to XDP_PACKET_HEADROOM for XDP setup.
No additional cache line is required for the new condition.
Fixes: 34db548bfb95 ("mlx4: add page recycling in receive path") Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Suggested-by: Martin KaFai Lau <kafai@fb.com> CC: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
CC [M] drivers/net/ethernet/freescale/fman/fman.o
In file included from ../drivers/net/ethernet/freescale/fman/fman.c:35:
../include/linux/fsl/guts.h: In function 'guts_set_dmacr':
../include/linux/fsl/guts.h:165:2: error: implicit declaration of function 'clrsetbits_be32' [-Werror=implicit-function-declaration]
clrsetbits_be32(&guts->dmacr, 3 << shift, device << shift);
^~~~~~~~~~~~~~~
Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: Madalin Bucur <madalin.bucur@nxp.com> Cc: netdev@vger.kernel.org Cc: linuxppc-dev@lists.ozlabs.org Signed-off-by: David S. Miller <davem@davemloft.net>
hv/netvsc: fix handling of fallback to single queue mode
The netvsc device may need to fallback to running in single queue
mode if host side only wants to support single queue.
Recent change for handling mtu broke this in setup logic.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Fixes: 3ffe64f1a641 ("hv_netvsc: split sub-channel setup into async and sync") Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Falcon [Fri, 13 Jul 2018 17:03:32 +0000 (12:03 -0500)]
ibmvnic: Revise RX/TX queue error messages
During a device failover, there may be latency between the loss
of the current backing device and a notification from firmware that
a failover has occurred. This latency can result in a large amount of
error printouts as firmware returns outgoing traffic with a generic
error code. These are not necessarily errors in this case as the
firmware is busy swapping in a new backing adapter and is not ready
to send packets yet. This patch reclassifies those error codes as
warnings with an explanation that a failover may be pending. All
other return codes will be considered errors.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
ipv6: make DAD fail with enhanced DAD when nonce length differs
Commit adc176c54722 ("ipv6 addrconf: Implemented enhanced DAD (RFC7527)")
added enhanced DAD with a nonce length of 6 bytes. However, RFC7527
doesn't specify the length of the nonce, other than being 6 + 8*k bytes,
with integer k >= 0 (RFC3971 5.3.2). The current implementation simply
assumes that the nonce will always be 6 bytes, but others systems are
free to choose different sizes.
If another system sends a nonce of different length but with the same 6
bytes prefix, it shouldn't be considered as the same nonce. Thus, check
that the length of the received nonce is the same as the length we sent.
Ugly scapy test script running on veth0:
def loop():
pkt=sniff(iface="veth0", filter="icmp6", count=1)
pkt = pkt[0]
b = bytearray(pkt[Raw].load)
b[1] += 1
b += b'\xde\xad\xbe\xef\xde\xad\xbe\xef'
pkt[Raw].load = bytes(b)
pkt[IPv6].plen += 8
# fixup checksum after modifying the payload
pkt[IPv6].payload.cksum -= 0x3b44
if pkt[IPv6].payload.cksum < 0:
pkt[IPv6].payload.cksum += 0xffff
sendp(pkt, iface="veth0")
This should result in DAD failure for any address added to veth0's peer,
but is currently ignored.
Fixes: adc176c54722 ("ipv6 addrconf: Implemented enhanced DAD (RFC7527)") Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Reviewed-by: Stefano Brivio <sbrivio@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch remove the following documentation warning
drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c:103: warning: Excess function parameter 'priv' description in 'stmmac_axi_setup'
It was introduced in commit afea03656add7 ("stmmac: rework DMA bus setting and introduce new platform AXI structure")
Signed-off-by: Corentin Labbe <clabbe@baylibre.com> Signed-off-by: David S. Miller <davem@davemloft.net>
A KASAN:use-after-free bug was found related to ip6-erspan
while running selftests/net/ip6_gre_headroom.sh
It happens because of following sequence:
- ipv6hdr pointer is obtained from skb
- skb_cow_head() is called, skb->head memory is reallocated
- old data is accessed using ipv6hdr pointer
skb_cow_head() call was added in e41c7c68ea77 ("ip6erspan: make sure
enough headroom at xmit."), but looking at the history there was a
chance of similar bug because gre_handle_offloads() and pskb_trim()
can also reallocate skb->head memory. Fixes tag points to commit
which introduced possibility of this bug.
This patch moves ipv6hdr pointer assignment after skb_cow_head() call.
Fixes: 5a963eb61b7c ("ip6_gre: Add ERSPAN native tunnel support") Signed-off-by: Prashant Bhole <bhole_prashant_q7@lab.ntt.co.jp> Reviewed-by: Greg Rose <gvrose8192@gmail.com> Acked-by: William Tu <u9012063@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
On XDP_TX we need to free up the frame only when tun_xdp_tx() returns a
negative value. A positive value indicates that the packet is
successfully enqueued to the ptr_ring, so freeing the page causes
use-after-free.
Fixes: 735fc4054b3a ("xdp: change ndo_xdp_xmit API to support bulking") Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp> Acked-by: Jason Wang <jasowang@redhat.com> Acked-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dave Watson [Thu, 12 Jul 2018 15:03:43 +0000 (08:03 -0700)]
tls: Stricter error checking in zerocopy sendmsg path
In the zerocopy sendmsg() path, there are error checks to revert
the zerocopy if we get any error code. syzkaller has discovered
that tls_push_record can return -ECONNRESET, which is fatal, and
happens after the point at which it is safe to revert the iter,
as we've already passed the memory to do_tcp_sendpages.
Previously this code could return -ENOMEM and we would want to
revert the iter, but AFAIK this no longer returns ENOMEM after a447da7d004 ("tls: fix waitall behavior in tls_sw_recvmsg"),
so we fail for all error codes.
Reported-by: syzbot+c226690f7b3126c5ee04@syzkaller.appspotmail.com Reported-by: syzbot+709f2810a6a05f11d4d3@syzkaller.appspotmail.com Signed-off-by: Dave Watson <davejwatson@fb.com> Fixes: 3c4d7559159b ("tls: kernel TLS support") Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Constantine Shulyupin <const@MakeLinux.com> Acked-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Biggers [Wed, 11 Jul 2018 17:46:29 +0000 (10:46 -0700)]
KEYS: DNS: fix parsing multiple options
My recent fix for dns_resolver_preparse() printing very long strings was
incomplete, as shown by syzbot which still managed to hit the
WARN_ONCE() in set_precision() by adding a crafted "dns_resolver" key:
precision 50001 too large
WARNING: CPU: 7 PID: 864 at lib/vsprintf.c:2164 vsnprintf+0x48a/0x5a0
The bug this time isn't just a printing bug, but also a logical error
when multiple options ("#"-separated strings) are given in the key
payload. Specifically, when separating an option string into name and
value, if there is no value then the name is incorrectly considered to
end at the end of the key payload, rather than the end of the current
option. This bypasses validation of the option length, and also means
that specifying multiple options is broken -- which presumably has gone
unnoticed as there is currently only one valid option anyway.
A similar problem also applied to option values, as the kstrtoul() when
parsing the "dnserror" option will read past the end of the current
option and into the next option.
Fix these bugs by correctly computing the length of the option name and
by copying the option value, null-terminated, into a temporary buffer.
Reproducer for "dnserror" option being parsed incorrectly (expected
behavior is to fail when seeing the unknown option "foo", actual
behavior was to read the dnserror value as "1#foo" and fail there):
Reported-by: syzbot <syzkaller@googlegroups.com> Fixes: 4a2d789267e0 ("DNS: If the DNS server returns an error, allow that to be cached [ver #2]") Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
multicast: init as INCLUDE when join SSM INCLUDE group
Based on RFC3376 5.1 and RFC3810 6.1, we should init as INCLUDE when join SSM
INCLUDE group. In my first version I only clear the group change record. But
this is not enough as when a new group join, it will init as EXCLUDE and
trigger an filter mode change in ip/ip6_mc_add_src(), which will clear all
source addresses' sf_crcount. This will prevent early joined address sending
state change records if multi source addresses joined at the same time.
In this v2 patchset, I fixed it by directly initializing the mode to INCLUDE
for SSM JOIN_SOURCE_GROUP. I also split the original patch into two separated
patches for IPv4 and IPv6.
Test: test by myself and customer.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Hangbin Liu [Tue, 10 Jul 2018 14:41:27 +0000 (22:41 +0800)]
ipv6/mcast: init as INCLUDE when join SSM INCLUDE group
This an IPv6 version patch of "ipv4/igmp: init group mode as INCLUDE when
join source group". From RFC3810, part 6.1:
If no per-interface state existed for that
multicast address before the change (i.e., the change consisted of
creating a new per-interface record), or if no state exists after the
change (i.e., the change consisted of deleting a per-interface
record), then the "non-existent" state is considered to have an
INCLUDE filter mode and an empty source list.
Which means a new multicast group should start with state IN(). Currently,
for MLDv2 SSM JOIN_SOURCE_GROUP mode, we first call ipv6_sock_mc_join(),
then ip6_mc_source(), which will trigger a TO_IN() message instead of
ALLOW().
The issue was exposed by commit a052517a8ff65 ("net/multicast: should not
send source list records when have filter mode change"). Before this change,
we sent both ALLOW(A) and TO_IN(A). Now, we only send TO_IN(A).
Fix it by adding a new parameter to init group mode. Also add some wrapper
functions to avoid changing too much code.
v1 -> v2:
In the first version I only cleared the group change record. But this is not
enough. Because when a new group join, it will init as EXCLUDE and trigger
a filter mode change in ip/ip6_mc_add_src(), which will clear all source
addresses sf_crcount. This will prevent early joined address sending state
change records if multi source addressed joined at the same time.
In v2 patch, I fixed it by directly initializing the mode to INCLUDE for SSM
JOIN_SOURCE_GROUP. I also split the original patch into two separated patches
for IPv4 and IPv6.
There is also a difference between v4 and v6 version. For IPv6, when the
interface goes down and up, we will send correct state change record with
unspecified IPv6 address (::) with function ipv6_mc_up(). But after DAD is
completed, we resend the change record TO_IN() in mld_send_initial_cr().
Fix it by sending ALLOW() for INCLUDE mode in mld_send_initial_cr().
Fixes: a052517a8ff65 ("net/multicast: should not send source list records when have filter mode change") Reviewed-by: Stefano Brivio <sbrivio@redhat.com> Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Hangbin Liu [Tue, 10 Jul 2018 14:41:26 +0000 (22:41 +0800)]
ipv4/igmp: init group mode as INCLUDE when join source group
Based on RFC3376 5.1
If no interface
state existed for that multicast address before the change (i.e., the
change consisted of creating a new per-interface record), or if no
state exists after the change (i.e., the change consisted of deleting
a per-interface record), then the "non-existent" state is considered
to have a filter mode of INCLUDE and an empty source list.
Which means a new multicast group should start with state IN().
Function ip_mc_join_group() works correctly for IGMP ASM(Any-Source Multicast)
mode. It adds a group with state EX() and inits crcount to mc_qrv,
so the kernel will send a TO_EX() report message after adding group.
But for IGMPv3 SSM(Source-specific multicast) JOIN_SOURCE_GROUP mode, we
split the group joining into two steps. First we join the group like ASM,
i.e. via ip_mc_join_group(). So the state changes from IN() to EX().
Then we add the source-specific address with INCLUDE mode. So the state
changes from EX() to IN(A).
Before the first step sends a group change record, we finished the second
step. So we will only send the second change record. i.e. TO_IN(A).
Regarding the RFC stands, we should actually send an ALLOW(A) message for
SSM JOIN_SOURCE_GROUP as the state should mimic the 'IN() to IN(A)'
transition.
The issue was exposed by commit a052517a8ff65 ("net/multicast: should not
send source list records when have filter mode change"). Before this change,
we used to send both ALLOW(A) and TO_IN(A). After this change we only send
TO_IN(A).
Fix it by adding a new parameter to init group mode. Also add new wrapper
functions so we don't need to change too much code.
v1 -> v2:
In my first version I only cleared the group change record. But this is not
enough. Because when a new group join, it will init as EXCLUDE and trigger
an filter mode change in ip/ip6_mc_add_src(), which will clear all source
addresses' sf_crcount. This will prevent early joined address sending state
change records if multi source addressed joined at the same time.
In v2 patch, I fixed it by directly initializing the mode to INCLUDE for SSM
JOIN_SOURCE_GROUP. I also split the original patch into two separated patches
for IPv4 and IPv6.
Fixes: a052517a8ff65 ("net/multicast: should not send source list records when have filter mode change") Reviewed-by: Stefano Brivio <sbrivio@redhat.com> Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 14 Jul 2018 01:30:19 +0000 (18:30 -0700)]
Merge branch 'fix-DCTCP-delayed-ACK'
Yuchung Cheng says:
====================
fix DCTCP delayed ACK
This patch series addresses the issue that sometimes DCTCP
fail to acknowledge the latest sequence and result in sender timeout
if inflight is small.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
After fixing the way DCTCP tracking delayed ACKs, the delayed-ACK
related callbacks are no longer needed
Signed-off-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Acked-by: Lawrence Brakmo <brakmo@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, when a data segment was sent an ACK was piggybacked
on the data segment without generating a CA_EVENT_NON_DELAYED_ACK
event to notify congestion control modules. So the DCTCP
ca->delayed_ack_reserved flag could incorrectly stay set when
in fact there were no delayed ACKs being reserved. This could result
in sending a special ECN notification ACK that carries an older
ACK sequence, when in fact there was no need for such an ACK.
DCTCP keeps track of the delayed ACK status with its own separate
state ca->delayed_ack_reserved. Previously it may accidentally cancel
the delayed ACK without updating this field upon sending a special
ACK that carries a older ACK sequence. This inconsistency would
lead to DCTCP receiver never acknowledging the latest data until the
sender times out and retry in some cases.
+0.010 < [ect0] W. 4501:5501(1000) ack 4 win 257
// Previously the ACK sequence below would be 4501, causing a long RTO
+0.040~+0.045 > [ect01] . 4:4(0) ack 5501 // delayed ack
+0.311 < [ect0] . 5501:6501(1000) ack 4 win 257 // More data
+0 > [ect01] . 4:4(0) ack 6501 // now acks everything
+0.500 < F. 9501:9501(0) ack 4 win 257
Reported-by: Larry Brakmo <brakmo@fb.com> Signed-off-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Acked-by: Lawrence Brakmo <brakmo@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Thu, 12 Jul 2018 12:23:45 +0000 (15:23 +0300)]
qlogic: check kstrtoul() for errors
We accidentally left out the error handling for kstrtoul().
Fixes: a520030e326a ("qlcnic: Implement flash sysfs callback for 83xx adapter") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix AF_XDP TX error reporting before final kernel release such that it
becomes consistent between copy mode and zero-copy, from Magnus.
2) Fix three different syzkaller reported issues: oob due to ld_abs
rewrite with too large offset, another oob in l3 based skb test run
and a bug leaving mangled prog in subprog JITing error path, from Daniel.
3) Fix BTF handling for bitfield extraction on big endian, from Okash.
4) Fix a missing linux/errno.h include in cgroup/BPF found by kbuild bot,
from Roman.
5) Fix xdp2skb_meta.sh sample by using just command names instead of
absolute paths for tc and ip and allow them to be redefined, from Taeung.
6) Fix availability probing for BPF seg6 helpers before final kernel ships
so they can be detected at prog load time, from Mathieu.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
skbuff: Unconditionally copy pfmemalloc in __skb_clone()
Commit 8b7008620b84 ("net: Don't copy pfmemalloc flag in
__copy_skb_header()") introduced a different handling for the
pfmemalloc flag in copy and clone paths.
In __skb_clone(), now, the flag is set only if it was set in the
original skb, but not cleared if it wasn't. This is wrong and
might lead to socket buffers being flagged with pfmemalloc even
if the skb data wasn't allocated from pfmemalloc reserves. Copy
the flag instead of ORing it.
Reported-by: Sabrina Dubroca <sd@queasysnail.net> Fixes: 8b7008620b84 ("net: Don't copy pfmemalloc flag in __copy_skb_header()") Signed-off-by: Stefano Brivio <sbrivio@redhat.com> Tested-by: Sabrina Dubroca <sd@queasysnail.net> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
This patch set adjusts the AF_XDP TX error reporting so that it becomes
consistent between copy mode and zero-copy. First some background:
Copy-mode for TX uses the SKB path in which the action of sending the
packet is performed from process context using the sendmsg
syscall. Completions are usually done asynchronously from NAPI mode by
using a TX interrupt. In this mode, send errors can be returned back
through the syscall.
In zero-copy mode both the sending of the packet and the completions
are done asynchronously from NAPI mode for performance reasons. In
this mode, the sendmsg syscall only makes sure that the TX NAPI loop
will be run that performs both the actions of sending and
completing. In this mode it is therefore not possible to return errors
through the sendmsg syscall as the sending is done from the NAPI
loop. Note that it is possible to implement a synchronous send with
our API, but in our benchmarks that made the TX performance drop by
nearly half due to synchronization requirements and cache line
bouncing. But for some netdevs this might be preferable so let us
leave it up to the implementation to decide.
The problem is that the current code base returns some errors in
copy-mode that are not possible to return in zero-copy mode. This
patch set aligns them so that the two modes always return the same
error code. We achieve this by removing some of the errors returned by
sendmsg in copy-mode (and in one case adding an error message for
zero-copy mode) and offering alternative error detection methods that
are consistent between the two modes.
The structure of the patch set is as follows:
Patch 1: removes the ENXIO return code from copy-mode when someone has
forcefully changed the number of queues on the device so that the
queue bound to the socket is no longer available. Just silently stop
sending anything as in zero-copy mode.
Patch 2: stop returning EAGAIN in copy mode when the completion queue
is full as zero-copy does not do this. Instead this situation can be
detected by comparing the head and tail pointers of the completion
queue in both modes. In any case, EAGAIN was not the correct error code
here since no amount of calling sendmsg will solve the problem. Only
consuming one or more messages on the completion queue will fix this.
Patch 3: Always return ENOBUFS from sendmsg if there is no TX queue
configured. This was not the case for zero-copy mode.
Patch 4: stop returning EMSGSIZE when the size of the packet is larger
than the MTU. Just send it to the device so that it will drop it as in
zero-copy mode.
Note that copy-mode can still return EAGAIN in certain circumstances,
but as these conditions cannot occur in zero-copy mode it is fine for
copy-mode to return them.
====================
Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Magnus Karlsson [Wed, 11 Jul 2018 08:12:52 +0000 (10:12 +0200)]
xsk: do not return EMSGSIZE in copy mode for packets larger than MTU
This patch stops returning EMSGSIZE from sendmsg in copy mode when the
size of the packet is larger than the MTU. Just send it to the device
so that it will drop it as in zero-copy mode. This makes the error
reporting consistent between copy mode and zero-copy mode.
Fixes: 35fcde7f8deb ("xsk: support for Tx") Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Magnus Karlsson [Wed, 11 Jul 2018 08:12:51 +0000 (10:12 +0200)]
xsk: always return ENOBUFS from sendmsg if there is no TX queue
This patch makes sure ENOBUFS is always returned from sendmsg if there
is no TX queue configured. This was not the case for zero-copy
mode. With this patch this error reporting is consistent between copy
mode and zero-copy mode.
Fixes: ac98d8aab61b ("xsk: wire upp Tx zero-copy functions") Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Magnus Karlsson [Wed, 11 Jul 2018 08:12:50 +0000 (10:12 +0200)]
xsk: do not return EAGAIN from sendmsg when completion queue is full
This patch stops returning EAGAIN in TX copy mode when the completion
queue is full as zero-copy does not do this. Instead this situation
can be detected by comparing the head and tail pointers of the
completion queue in both modes. In any case, EAGAIN was not the
correct error code here since no amount of calling sendmsg will solve
the problem. Only consuming one or more messages on the completion
queue will fix this.
With this patch, the error reporting becomes consistent between copy
mode and zero-copy mode.
Fixes: 35fcde7f8deb ("xsk: support for Tx") Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Magnus Karlsson [Wed, 11 Jul 2018 08:12:49 +0000 (10:12 +0200)]
xsk: do not return ENXIO from TX copy mode
This patch removes the ENXIO return code from TX copy-mode when
someone has forcefully changed the number of queues on the device so
that the queue bound to the socket is no longer available. Just
silently stop sending anything as in zero-copy mode so the error
reporting gets consistent between the two modes.
Fixes: 35fcde7f8deb ("xsk: support for Tx") Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Willem de Bruijn [Wed, 11 Jul 2018 16:00:46 +0000 (12:00 -0400)]
selftests: in udpgso_bench do not test udp zerocopy
The udpgso benchmark compares various configurations of UDP and TCP.
Including one that is not upstream, udp zerocopy. This is a leftover
from the earlier RFC patchset.
The test is part of kselftests and run in continuous spinners. Remove
the failing case to make the test start passing.
Fixes: 3a687bef148d ("selftests: udp gso benchmark") Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org> Signed-off-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Willem de Bruijn [Wed, 11 Jul 2018 16:00:45 +0000 (12:00 -0400)]
packet: reset network header if packet shorter than ll reserved space
If variable length link layer headers result in a packet shorter
than dev->hard_header_len, reset the network header offset. Else
skb->mac_len may exceed skb->len after skb_mac_reset_len.
packet_sendmsg_spkt already has similar logic.
Fixes: b84bbaf7a6c8 ("packet: in packet_snd start writing at link layer allocation") Signed-off-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: Don't copy pfmemalloc flag in __copy_skb_header()
The pfmemalloc flag indicates that the skb was allocated from
the PFMEMALLOC reserves, and the flag is currently copied on skb
copy and clone.
However, an skb copied from an skb flagged with pfmemalloc
wasn't necessarily allocated from PFMEMALLOC reserves, and on
the other hand an skb allocated that way might be copied from an
skb that wasn't.
So we should not copy the flag on skb copy, and rather decide
whether to allow an skb to be associated with sockets unrelated
to page reclaim depending only on how it was allocated.
Move the pfmemalloc flag before headers_start[0] using an
existing 1-bit hole, so that __copy_skb_header() doesn't copy
it.
When cloning, we'll now take care of this flag explicitly,
contravening to the warning comment of __skb_clone().
While at it, restore the newline usage introduced by commit b19372273164 ("net: reorganize sk_buff for faster
__copy_skb_header()") to visually separate bytes used in
bitfields after headers_start[0], that was gone after commit a9e419dc7be6 ("netfilter: merge ctinfo into nfct pointer storage
area"), and describe the pfmemalloc flag in the kernel-doc
structure comment.
This doesn't change the size of sk_buff or cacheline boundaries,
but consolidates the 15 bits hole before tc_index into a 2 bytes
hole before csum, that could now be filled more easily.
Reported-by: Patrick Talbert <ptalbert@redhat.com> Fixes: c93bdd0e03e8 ("netvm: allow skb allocation to use PFMEMALLOC reserves") Signed-off-by: Stefano Brivio <sbrivio@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
We should take and release the filter_sem consistently during the
reset process, in the same manner as the mac_lock and reset_lock.
For lockdep consistency we also take the filter_sem for write around
other calls to efx->type->init().
Fixes: c2bebe37c6b6 ("sfc: give ef10 its own rwsem in the filter table instead of filter_lock") Signed-off-by: Bert Kenward <bkenward@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
In some situations we may end up calling down_read while already
holding the semaphore for write, thus hanging. This has been seen
when setting the MAC address for the interface. The hung task log
in this situation includes this stack:
down_read
efx_ef10_filter_insert
efx_ef10_filter_insert_addr_list
efx_ef10_filter_vlan_sync_rx_mode
efx_ef10_filter_add_vlan
efx_ef10_filter_table_probe
efx_ef10_set_mac_address
efx_set_mac_address
dev_set_mac_address
In addition, lockdep rightly points out that nested calling of
down_read is incorrect.
Fixes: c2bebe37c6b6 ("sfc: give ef10 its own rwsem in the filter table instead of filter_lock") Tested-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Bert Kenward <bkenward@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: systemport: Fix CRC forwarding check for SYSTEMPORT Lite
SYSTEMPORT Lite reversed the logic compared to SYSTEMPORT, the
GIB_FCS_STRIP bit is set when the Ethernet FCS is stripped, and that bit
is not set by default. Fix the logic such that we properly check whether
that bit is set or not and we don't forward an extra 4 bytes to the
network stack.
Fixes: 44a4524c54af ("net: systemport: Add support for SYSTEMPORT Lite") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Stefan Baranoff [Tue, 10 Jul 2018 21:31:10 +0000 (17:31 -0400)]
tcp: allow user to create repair socket without window probes
Under rare conditions where repair code may be used it is possible that
window probes are either unnecessary or undesired. If the user knows that
window probes are not wanted or needed this change allows them to skip
sending them when a socket comes out of repair.
Signed-off-by: Stefan Baranoff <sbaranoff@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Stefan Baranoff [Tue, 10 Jul 2018 21:25:20 +0000 (17:25 -0400)]
tcp: fix sequence numbers for repaired sockets re-using TIME-WAIT sockets
This patch fixes a bug where the sequence numbers of a socket created using
TCP repair functionality are lower than set after connect is called.
This occurs when the repair socket overlaps with a TIME-WAIT socket and
triggers the re-use code. The amount lower is equal to the number of times
that a particular IP/port set is re-used and then put back into TIME-WAIT.
Re-using the first time the sequence number is 1 lower, closing that socket
and then re-opening (with repair) a new socket with the same addresses/ports
puts the sequence number 2 lower than set via setsockopt. The third time is
3 lower, etc. I have not tested what the limit of this acrewal is, if any.
The fix is, if a socket is in repair mode, to respect the already set
sequence number and timestamp when it would have already re-used the
TIME-WAIT socket.
Signed-off-by: Stefan Baranoff <sbaranoff@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
What happens in jit_subprogs() is that kcalloc() for the subprog func
buffer is failing with NULL where we then bail out. Latter is a plain
return -ENOMEM, and this is definitely not okay since earlier in the
loop we are walking all subprogs and temporarily rewrite insn->off to
remember the subprog id as well as insn->imm to temporarily point the
call to __bpf_call_base + 1 for the initial JIT pass. Thus, bailing
out in such state and handing this over to the interpreter is troublesome
since later/subsequent e.g. find_subprog() lookups are based on wrong
insn->imm.
Therefore, once we hit this point, we need to jump to out_free path
where we undo all changes from earlier loop, so that interpreter can
work on unmodified insn->{off,imm}.
Another point is that should find_subprog() fail in jit_subprogs() due
to a verifier bug, then we also should not simply defer the program to
the interpreter since also here we did partial modifications. Instead
we should just bail out entirely and return an error to the user who is
trying to load the program.
Fixes: 1c2a088a6626 ("bpf: x64: add JIT support for multi-function programs") Reported-by: syzbot+7d427828b2ea6e592804@syzkaller.appspotmail.com Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Jacob Keller [Tue, 10 Jul 2018 21:22:27 +0000 (14:22 -0700)]
sch_fq_codel: zero q->flows_cnt when fq_codel_init fails
When fq_codel_init fails, qdisc_create_dflt will cleanup by using
qdisc_destroy. This function calls the ->reset() op prior to calling the
->destroy() op.
Unfortunately, during the failure flow for sch_fq_codel, the ->flows
parameter is not initialized, so the fq_codel_reset function will null
pointer dereference.
This is caused because flows_cnt is non-zero, but flows hasn't been
initialized. fq_codel_init has left the private data in a partially
initialized state.
To fix this, reset flows_cnt to 0 when we fail to initialize.
Additionally, to make the state more consistent, also cleanup the flows
pointer when the allocation of backlogs fails.
This fixes the NULL pointer dereference, since both the for-loop and
memset in fq_codel_reset will be no-ops when flow_cnt is zero.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Documentation/networking/e1000.rst:83: ERROR: Unexpected indentation.
Documentation/networking/e1000.rst:84: WARNING: Block quote ends without a blank line; unexpected unindent.
Documentation/networking/e1000.rst:173: WARNING: Definition list ends without a blank line; unexpected unindent.
Documentation/networking/e1000.rst:236: WARNING: Definition list ends without a blank line; unexpected unindent.
While here, fix highlights and mark a table as such.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Dan Carpenter [Wed, 4 Jul 2018 09:53:37 +0000 (12:53 +0300)]
ixgbe: Off by one in ixgbe_ipsec_tx()
The ipsec->tx_tbl[] has IXGBE_IPSEC_MAX_SA_COUNT elements so the > needs
to be changed to >= so we don't read one element beyond the end of the
array.
Fixes: 592594704761 ("ixgbe: process the Tx ipsec offload") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Shannon Nelson <shannon.nelson@oracle.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Mon, 18 Jun 2018 16:02:00 +0000 (12:02 -0400)]
ixgbe: Be more careful when modifying MAC filters
This change makes it so that we are much more explicit about the ordering
of updates to the receive address register (RAR) table. Prior to this patch
I believe we may have been updating the table while entries were still
active, or possibly allowing for reordering of things since we weren't
explicitly flushing writes to either the lower or upper portion of the
register prior to accessing the other half.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Reviewed-by: Shannon Nelson <shannon.nelson@oracle.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
David S. Miller [Thu, 12 Jul 2018 07:19:06 +0000 (00:19 -0700)]
Merge branch 'ieee802154-for-davem-2018-07-11' of git://git.kernel.org/pub/scm/linux/kernel/git/sschmidt/wpan
Stefan Schmidt says:
====================
pull-request: ieee802154 for net 2018-07-11
An update from ieee802154 for your *net* tree.
Build system fix for a missing include from Arnd Bergmann.
Setting the IFLA_LINK for the lowpan parent from Lubomir Rintel.
Fixes for some RX corner cases in adf7242 driver by Michael Hennerich.
And some small patches to cleanup our BUG_ON vs WARN_ON usage.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Tue, 10 Jul 2018 11:05:36 +0000 (12:05 +0100)]
sfp: fix module initialisation with netdev already up
It was been observed that with a particular order of initialisation,
the netdev can be up, but the SFP module still has its TX_DISABLE
signal asserted. This occurs when the network device brought up before
the SFP kernel module has been inserted by userspace.
This occurs because sfp-bus layer does not hear about the change in
network device state, and so assumes that it is still down. Set
netdev->sfp when the upstream is registered to work around this problem.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Tue, 10 Jul 2018 11:05:31 +0000 (12:05 +0100)]
sfp: ensure we clean up properly on bus registration failure
We fail to correctly clean up after a bus registration failure, which
can lead to an incorrect assumption about the registration state of
the upstream or sfp cage.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
After scrubbing the BPF prog a bit from the noise, turns out it called
bpf_skb_change_head() for the lwt_xmit prog with headroom of 2. Nothing
wrong in that, however, this was run with repeat >> 0 in bpf_prog_test_run_skb()
and the same skb thus keeps changing until the pskb_expand_head() called
from skb_cow() keeps bailing out in atomic alloc context with -ENOMEM.
So upon return we'll basically have 0 headroom left yet blindly do the
__skb_push() of 14 bytes and keep copying data from there in bpf_test_finish()
out of bounds. Fix to check if we have enough headroom and if pskb_expand_head()
fails, bail out with error.
Another bug independent of this fix (but related in triggering above) is
that BPF_PROG_TEST_RUN should be reworked to reset the skb/xdp buffer to
it's original state from input as otherwise repeating the same test in a
loop won't work for benchmarking when underlying input buffer is getting
changed by the prog each time and reused for the next run leading to
unexpected results.
When extracting bitfield from a number, btf_int_bits_seq_show() builds
a mask and accesses least significant byte of the number in a way
specific to little-endian. This patch fixes that by checking endianness
of the machine and then shifting left and right the unneeded bits.
Thanks to Martin Lau for the help in navigating potential pitfalls when
dealing with endianess and for the final solution.
Fixes: b00b8daec828 ("bpf: btf: Add pretty print capability for data with BTF type info") Signed-off-by: Okash Khawaja <osk@fb.com> Acked-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
bpf_lwt_seg6_* helpers require CONFIG_IPV6_SEG6_BPF, and currently
return -EOPNOTSUPP to indicate unavailability. This patch forces the
BPF verifier to reject programs using these helpers when
!CONFIG_IPV6_SEG6_BPF, allowing users to more easily probe if they are
available or not.
Signed-off-by: Mathieu Xhonneux <m.xhonneux@gmail.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Daniel Borkmann [Mon, 9 Jul 2018 22:43:22 +0000 (00:43 +0200)]
bpf: fix ldx in ld_abs rewrite for large offsets
Mark reported that syzkaller triggered a KASAN detected slab-out-of-bounds
bug in ___bpf_prog_run() with a BPF_LD | BPF_ABS word load at offset 0x8001.
After further investigation it became clear that the issue was the
BPF_LDX_MEM() which takes offset as an argument whereas it cannot encode
larger than S16_MAX offsets into it. For this synthetical case we need to
move the full address into tmp register instead and do the LDX without
immediate value.
Fixes: e0cea7ce988c ("bpf: implement ld_abs/ld_ind in native bpf") Reported-by: syzbot <syzkaller@googlegroups.com> Reported-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Alexei Starovoitov <ast@kernel.org>
rhashtable: add restart routine in rhashtable_free_and_destroy()
rhashtable_free_and_destroy() cancels re-hash deferred work
then walks and destroys elements. at this moment, some elements can be
still in future_tbl. that elements are not destroyed.
test case:
nft_rhash_destroy() calls rhashtable_free_and_destroy() to destroy
all elements of sets before destroying sets and chains.
But rhashtable_free_and_destroy() doesn't destroy elements of future_tbl.
so that splat occurred.
David S. Miller [Mon, 9 Jul 2018 23:27:15 +0000 (16:27 -0700)]
Merge branch 'bnxt_en-Bug-fixes'
Michael Chan says:
====================
bnxt_en: Bug fixes.
These are bug fixes in error code paths, TC Flower VLAN TCI flow
checking bug fix, proper filtering of Broadcast packets if IFF_BROADCAST
is not set, and a bug fix in bnxt_get_max_rings() to return 0 ring
parameters when the return value is -ENOMEM.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix bug in the error code path when bnxt_request_irq() returns failure.
bnxt_disable_napi() should not be called in this error path because
NAPI has not been enabled yet.
Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.") Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Mon, 9 Jul 2018 06:24:51 +0000 (02:24 -0400)]
bnxt_en: Do not modify max IRQ count after RDMA driver requests/frees IRQs.
Calling bnxt_set_max_func_irqs() to modify the max IRQ count requested or
freed by the RDMA driver is flawed. The max IRQ count is checked when
re-initializing the IRQ vectors and this can happen multiple times
during ifup or ethtool -L. If the max IRQ is reduced and the RDMA
driver is operational, we may not initailize IRQs correctly. This
problem shows up on VFs with very small number of MSIX.
There is no other logic that relies on the IRQ count excluding the ones
used by RDMA. So we fix it by just removing the call to subtract or
add the IRQs used by RDMA.
Fixes: a588e4580a7e ("bnxt_en: Add interface to support RDMA driver.") Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Mon, 9 Jul 2018 06:24:50 +0000 (02:24 -0400)]
bnxt_en: Support clearing of the IFF_BROADCAST flag.
Currently, the driver assumes IFF_BROADCAST is always set and always sets
the broadcast filter. Modify the code to set or clear the broadcast
filter according to the IFF_BROADCAST flag.
Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Mon, 9 Jul 2018 06:24:49 +0000 (02:24 -0400)]
bnxt_en: Always set output parameters in bnxt_get_max_rings().
The current code returns -ENOMEM and does not bother to set the output
parameters to 0 when no rings are available. Some callers, such as
bnxt_get_channels() will display garbage ring numbers when that happens.
Fix it by always setting the output parameters.
Fixes: 6e6c5a57fbe1 ("bnxt_en: Modify bnxt_get_max_rings() to support shared or non shared rings.") Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
If there aren't enough RX rings available, the driver will attempt to
use a single RX ring without the aggregation ring. If that also
fails, the BNXT_FLAG_AGG_RINGS flag is cleared but the other ring
parameters are not set consistently to reflect that. If more RX
rings become available at the next open, the RX rings will be in
an inconsistent state and may crash when freeing the RX rings.
Fix it by restoring the BNXT_FLAG_AGG_RINGS if not enough RX rings are
available to run without aggregation rings.
Fixes: bdbd1eb59c56 ("bnxt_en: Handle no aggregation ring gracefully.") Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible that OVS may set don’t care for DEI/CFI bit in
vlan_tci mask. Hence, checking for vlan_tci exact match will endup
in a vlan flow rejection.
This patch fixes the problem by checking for vlan_pcp and vid
separately, instead of checking for the entire vlan_tci.
Fixes: e85a9be93cf1 (bnxt_en: do not allow wildcard matches for L2 flows) Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The following patchset contains Netfilter fixes for your net tree:
1) Missing module autoloadfor icmp and icmpv6 x_tables matches,
from Florian Westphal.
2) Possible non-linear access to TCP header from tproxy, from
Mate Eckl.
3) Do not allow rbtree to be used for single elements, this patch
moves all set backend into one single module since such thing
can only happen if hashtable module is explicitly blacklisted,
which should not ever be done.
4) Reject error and standard targets from nft_compat for sanity
reasons, they are never used from there.
5) Don't crash on double hashsize module parameter, from Andrey
Ryabinin.
6) Drop dst on skb before placing it in the fragmentation
reassembly queue, from Florian Westphal.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
netfilter: ipv6: nf_defrag: drop skb dst before queueing
Eric Dumazet reports:
Here is a reproducer of an annoying bug detected by syzkaller on our production kernel
[..]
./b78305423 enable_conntrack
Then :
sleep 60
dmesg | tail -10
[ 171.599093] unregister_netdevice: waiting for lo to become free. Usage count = 2
[ 181.631024] unregister_netdevice: waiting for lo to become free. Usage count = 2
[ 191.687076] unregister_netdevice: waiting for lo to become free. Usage count = 2
[ 201.703037] unregister_netdevice: waiting for lo to become free. Usage count = 2
[ 211.711072] unregister_netdevice: waiting for lo to become free. Usage count = 2
[ 221.959070] unregister_netdevice: waiting for lo to become free. Usage count = 2
Reproducer sends ipv6 fragment that hits nfct defrag via LOCAL_OUT hook.
skb gets queued until frag timer expiry -- 1 minute.
Normally nf_conntrack_reasm gets called during prerouting, so skb has
no dst yet which might explain why this wasn't spotted earlier.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com> Reported-by: John Sperbeck <jsperbeck@google.com> Signed-off-by: Florian Westphal <fw@strlen.de> Tested-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
projects / mirror_ubuntu-focal-kernel.git / log