Merely enabling CONFIG_COMPILE_TEST should not enable additional code.
To fix this, restrict the automatic enabling of ROCKCHIP_GRF to
ARCH_ROCKCHIP, and ask the user in case of compile-testing.
Without this patch, the TDA19971 chip's EDID is inactive.
EDID never worked with this driver, it was all tested with HDMI signal
sources which don't need EDID support.
The list_for_each_entry() iterator, "connector" in this code, can never be
NULL. If we exit the loop without finding the correct connector then
"connector" points invalid memory that is an offset from the list head.
This will eventually lead to memory corruption and presumably a kernel
crash.
Fixes: 9bd81acdb648 ("gma500: Convert Oaktrail to work with new output handling") Signed-off-by: Harshvardhan Jha <harshvardhan.jha@oracle.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Link: https://patchwork.freedesktop.org/patch/msgid/20210709073959.11443-1-harshvardhan.jha@oracle.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
MCDDRCFG is a per-channel register and uses bit{0,1} to indicate
the NVDIMM presence on DIMM slot{0,1}. Current i10nm_edac driver
wrongly uses MCDDRCFG as per-DIMM register and fails to detect
the NVDIMM.
Fix it by reading MCDDRCFG as per-channel register and using its
bit{0,1} to check whether the NVDIMM is populated on DIMM slot{0,1}.
Fixes: d4dc89d069aa ("EDAC, i10nm: Add a driver for Intel 10nm server processors") Reported-by: Fan Du <fan.du@intel.com> Tested-by: Wen Jin <wen.jin@intel.com> Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com> Signed-off-by: Tony Luck <tony.luck@intel.com> Link: https://lore.kernel.org/r/20210818175701.1611513-2-tony.luck@intel.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The function wait_for_completion_interruptible_timeout will return
-ERESTARTSYS immediately when receiving SIGKILL signal which is sent
by "jffs2_gcd_mtd" during umounting jffs2. This will break the SPI memory
operation because the data transmitting may begin before the command or
address transmitting completes. Use wait_for_completion_timeout to prevent
the process from being interruptible.
Fixes: 67dca5e580f1 ("spi: spi-mem: Add support for Zynq QSPI controller") Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com> Link: https://lore.kernel.org/r/20210826005930.20572-1-quanyang.wang@windriver.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Use 50ms as default timeout value and the time clock is 32768HZ.
The original value of WDG_LOAD_VAL is not correct, so this patch
fixes it.
Fixes: ac1775012058 ("spi: sprd: Add the support of restarting the system") Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com> Link: https://lore.kernel.org/r/20210826091549.2138125-2-zhang.lyra@gmail.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
vctrl_enable() and vctrl_disable() call regulator_enable() and
regulator_disable(), respectively. However, vctrl_* are regulator ops
and should not be calling the locked regulator APIs. Doing so results in
a lockdep warning.
Instead of exporting more internal regulator ops, model the ctrl supply
as an actual supply to vctrl-regulator. At probe time this driver still
needs to use the consumer API to fetch its constraints, but otherwise
lets the regulator core handle the upstream supply for it.
The enable/disable/is_enabled ops are not removed, but now only track
state internally. This preserves the original behavior with the ops
being available, but one could argue that the original behavior was
already incorrect: the internal state would not match the upstream
supply if that supply had another consumer that enabled the supply,
while vctrl-regulator was not enabled.
The lockdep warning is as follows:
WARNING: possible circular locking dependency detected
5.14.0-rc6 #2 Not tainted
------------------------------------------------------
swapper/0/1 is trying to acquire lock: ffffffc011306d00 (regulator_list_mutex){+.+.}-{3:3}, at:
regulator_lock_dependent (arch/arm64/include/asm/current.h:19
include/linux/ww_mutex.h:111
drivers/regulator/core.c:329)
but task is already holding lock: ffffff8004a77160 (regulator_ww_class_mutex){+.+.}-{3:3}, at:
regulator_lock_recursive (drivers/regulator/core.c:156
drivers/regulator/core.c:263)
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
In commit e9153311491d ("regulator: vctrl-regulator: Avoid deadlock getting
and setting the voltage"), all calls to get/set the voltage of the
control regulator were switched to unlocked versions to avoid deadlocks.
However, the call in the probe path is done without regulator locks
held. In this case the locked version should be used.
Switch back to the locked regulator_get_voltage() in the probe path to
avoid any mishaps.
Fixes: e9153311491d ("regulator: vctrl-regulator: Avoid deadlock getting and setting the voltage") Signed-off-by: Chen-Yu Tsai <wenst@chromium.org> Link: https://lore.kernel.org/r/20210825033704.3307263-2-wenst@chromium.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
When a fatal machine check results in a system reset, Linux does not
clear the error(s) from machine check bank(s) - hardware preserves the
machine check banks across a warm reset.
During initialization of the kernel after the reboot, Linux reads, logs,
and clears all machine check banks.
But there is a problem. In:
5de97c9f6d85 ("x86/mce: Factor out and deprecate the /dev/mcelog driver")
the call to mce_register_decode_chain() moved later in the boot
sequence. This means that /dev/mcelog doesn't see those early error
logs.
This was partially fixed by:
cd9c57cad3fe ("x86/MCE: Dump MCE to dmesg if no consumers")
which made sure that the logs were not lost completely by printing
to the console. But parsing console logs is error prone. Users of
/dev/mcelog should expect to find any early errors logged to standard
places.
Add a new flag MCP_QUEUE_LOG to machine_check_poll() to be used in early
machine check initialization to indicate that any errors found should
just be queued to genpool. When mcheck_late_init() is called it will
call mce_schedule_work() to actually log and flush any errors queued in
the genpool.
[ Based on an original patch, commit message by and completely
productized by Tony Luck. ]
Fixes: 5de97c9f6d85 ("x86/mce: Factor out and deprecate the /dev/mcelog driver") Reported-by: Sumanth Kamatala <skamatala@juniper.net> Signed-off-by: Borislav Petkov <bp@suse.de> Signed-off-by: Tony Luck <tony.luck@intel.com> Signed-off-by: Borislav Petkov <bp@suse.de> Link: https://lkml.kernel.org/r/20210824003129.GA1642753@agluck-desk2.amr.corp.intel.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The issue is caused by the following call that is interrupted while
waiting for the TPM's response.
sig = wait_event_interruptible(ibmvtpm->wq, !ibmvtpm->tpm_processing_cmd);
Rather than waiting for the response in the low level driver, have it use
the polling loop in tpm_try_transmit() that uses a command's duration to
poll until a result has been returned by the TPM, thus ending when the
timeout has occurred but not responding to signals and ctrl-c anymore. To
stay in this polling loop extend tpm_ibmvtpm_status() to return
'true' for as long as the vTPM is indicated as being busy in
tpm_processing_cmd. Since the loop requires the TPM's timeouts, get them
now using tpm_get_timeouts() after setting the TPM2 version flag on the
chip.
To recreat the resolved issue start rngd like this:
Address a kbuild issue where a developer created an ECDSA key for signing
kernel modules and then builds an older version of the kernel, when bi-
secting the kernel for example, that does not support ECDSA keys.
If openssl is installed, trigger the creation of an RSA module signing
key if it is not an RSA key.
Fixes: cfc411e7fff3 ("Move certificate handling to its own directory") Cc: David Howells <dhowells@redhat.com> Cc: David Woodhouse <dwmw2@infradead.org> Signed-off-by: Stefan Berger <stefanb@linux.ibm.com> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Tested-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
When non-secure priorities are used, compared to the raw priority set,
the value read back from RPR is also right-shifted by one and the
highest bit set.
Add a macro to do the modifications to the raw priority when doing the
comparison against the RPR value. This corrects the pseudo-NMI behavior
when non-secure priorities in the GIC are used. Tested on 5.10 with
the "IPI as pseudo-NMI" series [1] applied on MT8195.
If CMT instance has at least two channels, one channel will be used
as a clock source and another one used as a clock event device.
In that case, IRQ is not requested for clock source channel so
sh_cmt_clock_event_program_verify() might work incorrectly.
Besides, when a channel is only used for clock source, don't need to
re-set the next match_value since it should be maximum timeout as
it still is.
On the other hand, due to no IRQ, total_cycles is not counted up
when reaches compare match time (timer counter resets to zero),
so sh_cmt_clocksource_read() returns unexpected value.
Therefore, use 64-bit clocksoure's mask for 32-bit or 16-bit variants
will also lead to wrong delta calculation. Hence, this mask should
correspond to timer counter width, and above function just returns
the raw value of timer counter register.
We should set the additional space to 0 in mpi_resize().
So use kcalloc() instead of kmalloc_array().
In lib/mpi/ec.c:
/****************
* Resize the array of A to NLIMBS. the additional space is cleared
* (set to 0) [done by m_realloc()]
*/
int mpi_resize(MPI a, unsigned nlimbs)
Like the comment of kernel's mpi_resize() said, the additional space
need to be set to 0, but when a->d is not NULL, it does not set.
The kernel's mpi lib is from libgcrypt, the mpi resize in libgcrypt
is _gcry_mpi_resize() which set the additional space to 0.
This bug may cause mpi api which use mpi_resize() get wrong result
under the condition of using the additional space without initiation.
If this condition is not met, the bug would not be triggered.
Currently in kernel, rsa, sm2 and dh use mpi lib, and they works well,
so the bug is not triggered in these cases.
add_points_edwards() use the additional space directly, so it will
get a wrong result.
Fixes: cdec9cb5167a ("crypto: GnuPG based MPI lib - source files (part 1)") Signed-off-by: Hongbo Li <herberthbli@tencent.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Depending on the DMA driver being used, the struct dma_slave_config may
need to be initialized to zero for the unused data.
For example, we have three DMA drivers using src_port_window_size and
dst_port_window_size. If these are left uninitialized, it can cause DMA
failures.
For spi-pic32, this is probably not currently an issue but is still good to
fix though.
Fixes: 1bcb9f8ceb67 ("spi: spi-pic32: Add PIC32 SPI master driver") Cc: Purna Chandra Mandal <purna.mandal@microchip.com> Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com> Cc: Vinod Koul <vkoul@kernel.org> Signed-off-by: Tony Lindgren <tony@atomide.com> Link: https://lore.kernel.org/r/20210810081727.19491-2-tony@atomide.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Depending on the DMA driver being used, the struct dma_slave_config may
need to be initialized to zero for the unused data.
For example, we have three DMA drivers using src_port_window_size and
dst_port_window_size. If these are left uninitialized, it can cause DMA
failures.
For spi-fsl-dspi, this is probably not currently an issue but is still
good to fix though.
Fixes: 90ba37033cb9 ("spi: spi-fsl-dspi: Add DMA support for Vybrid") Cc: Sanchayan Maity <maitysanchayan@gmail.com> Cc: Vladimir Oltean <vladimir.oltean@nxp.com> Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com> Cc: Vinod Koul <vkoul@kernel.org> Signed-off-by: Tony Lindgren <tony@atomide.com> Acked-by: Vladimir Oltean <vladimir.oltean@nxp.com> Link: https://lore.kernel.org/r/20210810081727.19491-1-tony@atomide.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
When merging one bio to request, if they are discard IO and the queue
supports multi-range discard, we need to return ELEVATOR_DISCARD_MERGE
because both block core and related drivers(nvme, virtio-blk) doesn't
handle mixed discard io merge(traditional IO merge together with
discard merge) well.
Fix the issue by returning ELEVATOR_DISCARD_MERGE in this situation,
so both blk-mq and drivers just need to handle multi-range discard.
When enabling CONFIG_RMW_INSNS in e.g. a Coldfire build:
{standard input}:3068: Error: invalid instruction for this architecture; needs 68020 or higher (68020 [68k, 68ec020], 68030 [68ec030], 68040 [68ec040], 68060 [68ec060]) -- statement `casl %d4,%d0,(%a6)' ignored
Fix this by (a) adding a new config symbol to track if support for any
CPU that lacks the CAS instruction is enabled, and (b) making
CONFIG_RMW_INSNS depend on the new symbol not being set.
If rcu_print_task_stall() is invoked on an rcu_node structure that does
not contain any tasks blocking the current grace period, it takes an
early exit that fails to release that rcu_node structure's lock. This
results in a self-deadlock, which is detected by lockdep.
This will also result in other complaints, including RCU's scheduler
hook complaining about blocking rather than preemption and an rcutorture
writer stall.
Only a partial RCU CPU stall warning message will be printed because of
the self-deadlock.
This commit therefore releases the lock on the rcu_print_task_stall()
function's early exit path.
Fixes: c583bcb8f5ed ("rcu: Don't invoke try_invoke_on_locked_down_task() with irqs disabled") Tested-by: Qais Yousef <qais.yousef@arm.com> Signed-off-by: Yanfei Xu <yanfei.xu@windriver.com> Signed-off-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
This commit adds a number of lockdep_assert_irqs_disabled() calls
to rcu_sched_clock_irq() and a number of the functions that it calls.
The point of this is to help track down a situation where lockdep appears
to be insisting that interrupts are enabled within these functions, which
should only ever be invoked from the scheduling-clock interrupt handler.
Link: https://lore.kernel.org/lkml/20201111133813.GA81547@elver.google.com/ Signed-off-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The for loop in rcu_print_task_stall() always omits ts[0], which points
to the first task blocking the stalled grace period. This in turn fails
to count this first task, which means that ndetected will be equal to
zero when all CPUs have passed through their quiescent states and only
one task is blocking the stalled grace period. This zero value for
ndetected will in turn result in an incorrect "All QSes seen" message:
rcu: INFO: rcu_preempt detected stalls on CPUs/tasks:
rcu: Tasks blocked on level-1 rcu_node (CPUs 12-23):
(detected by 15, t=6504 jiffies, g=164777, q=9011209)
rcu: All QSes seen, last rcu_preempt kthread activity 1 (4295252379-4295252378), jiffies_till_next_fqs=1, root ->qsmask 0x2
BUG: sleeping function called from invalid context at include/linux/uaccess.h:156
in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 70613, name: msgstress04
INFO: lockdep is turned off.
Preemption disabled at:
[<ffff8000104031a4>] create_object.isra.0+0x204/0x4b0
CPU: 15 PID: 70613 Comm: msgstress04 Kdump: loaded Not tainted
5.12.2-yoctodev-standard #1
Hardware name: Marvell OcteonTX CN96XX board (DT)
Call trace:
dump_backtrace+0x0/0x2cc
show_stack+0x24/0x30
dump_stack+0x110/0x188
___might_sleep+0x214/0x2d0
__might_sleep+0x7c/0xe0
This commit therefore fixes the loop to include ts[0].
Fixes: c583bcb8f5ed ("rcu: Don't invoke try_invoke_on_locked_down_task() with irqs disabled") Tested-by: Qais Yousef <qais.yousef@arm.com> Signed-off-by: Yanfei Xu <yanfei.xu@windriver.com> Signed-off-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The UCLAMP_FLAG_IDLE flag is set on a runqueue when dequeueing the last
uclamp active task (that is, when buckets.tasks reaches 0 for all
buckets) to maintain the last uclamp.max and prevent blocked util from
suddenly becoming visible.
However, there is an asymmetry in how the flag is set and cleared which
can lead to having the flag set whilst there are active tasks on the rq.
Specifically, the flag is cleared in the uclamp_rq_inc() path, which is
called at enqueue time, but set in uclamp_rq_dec_id() which is called
both when dequeueing a task _and_ in the update_uclamp_active() path. As
a result, when both uclamp_rq_{dec,ind}_id() are called from
update_uclamp_active(), the flag ends up being set but not cleared,
hence leaving the runqueue in a broken state.
Fix this by clearing the flag in update_uclamp_active() as well.
In the for loop all nfeth_dev array members should be freed, not only
the first one. Freeing only the first array member can cause
double-free bugs and memory leaks.
Fixes: 9cd7b148312f ("m68k/atari: ARAnyM - Add support for network access") Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Link: https://lore.kernel.org/r/20210705204727.10743-1-paskripkin@gmail.com Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
If for any reason the interrupt enable for an ap queue fails the
state machine run for the queue returned wrong return codes to the
caller. So the caller assumed interrupt support for this queue in
enabled and thus did not re-establish the high resolution timer used
for polling. In the end this let to a hang for the user space process
waiting "forever" for the reply.
This patch reworks these return codes to return correct indications
for the caller to re-establish the timer when a queue runs without
interrupt support.
Please note that this is fixing a wrong behavior after a first
failure (enable interrupt support for the queue) failed. However,
looks like this occasionally happens on KVM systems.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com> Signed-off-by: Heiko Carstens <hca@linux.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Currently allocation and registration of s390dbf debug areas are tied
together. As a result, a debug area cannot be unregistered and
re-registered while any process has an associated debugfs file open.
Fix this by splitting alloc/release from register/unregister.
Signed-off-by: Peter Oberparleiter <oberpar@linux.ibm.com> Signed-off-by: Heiko Carstens <hca@linux.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Any previously recorded s390dbf debug data is reset when a debug area
is resized using the 'pages' sysfs attribute. This can make
live-debugging unnecessarily complex.
Fix this by copying existing debug data to the newly allocated debug
area when resizing.
Signed-off-by: Peter Oberparleiter <oberpar@linux.ibm.com> Signed-off-by: Heiko Carstens <hca@linux.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Currently clp_set_pci_fn() always returns 0 as long as the CLP request
itself succeeds even if the operation itself returns a response code
other than CLP_RC_OK or CLP_RC_SETPCIFN_ALRDY. This is highly misleading
because calling code assumes that a zero rc means that the operation was
successful.
Fix this by returning the response code or cc on failure with the
exception of the special handling for CLP_RC_SETPCIFN_ALRDY. Also let's
not assume that the returned function handle for CLP_RC_SETPCIFN_ALRDY
is 0, we don't need it anyway.
&dev->event_lock is HARDIRQ-safe, so interrupts have to be disabled
while grabbing &fasync_struct.fa_lock, otherwise we invert the lock
hierarchy. However, since kill_fasync which calls kill_fasync_rcu is
an exported symbol, it may not necessarily be called with interrupts
disabled.
As kill_fasync_rcu may be called with interrupts disabled (for
example, in the call chain above), we replace calls to
read_lock/read_unlock on &fasync_struct.fa_lock in kill_fasync_rcu
with read_lock_irqsave/read_unlock_irqrestore.
Signed-off-by: Desmond Cheong Zhi Xi <desmondcheongzx@gmail.com> Signed-off-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The function adf_iov_putmsg() is only used inside the intel_qat module
therefore should not be exported.
Remove EXPORT_SYMBOL for the function adf_iov_putmsg().
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com> Reviewed-by: Fiona Trahe <fiona.trahe@intel.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Use reinit_completion() to set to a clean state a completion variable,
used to coordinate the VF to PF request-response flow, before every
new VF request.
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com> Co-developed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com> Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com> Reviewed-by: Fiona Trahe <fiona.trahe@intel.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The top half of the VF drivers handled only a source at the time.
If an interrupt for PF2VF and bundle occurred at the same time, the ISR
scheduled only the bottom half for PF2VF.
This patch fixes the VF top half so that if both sources of interrupt
trigger at the same time, both bottom halves are scheduled.
This patch is based on earlier work done by Conor McLoughlin.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com> Reviewed-by: Marco Chiappero <marco.chiappero@intel.com> Reviewed-by: Fiona Trahe <fiona.trahe@intel.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The function adf_dev_init() ignores the error code reported by
enable_vf2pf_comms(). If the latter fails, e.g. the VF is not compatible
with the pf, then the load of the VF driver progresses.
This patch changes adf_dev_init() so that the error code from
enable_vf2pf_comms() is returned to the caller.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com> Reviewed-by: Marco Chiappero <marco.chiappero@intel.com> Reviewed-by: Fiona Trahe <fiona.trahe@intel.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
lockdep complains that in omap-aes, the list_lock is taken both with
softirqs enabled at probe time, and also in softirq context, which
could lead to a deadlock:
================================
WARNING: inconsistent lock state 5.14.0-rc1-00035-gc836005b01c5-dirty #69 Not tainted
--------------------------------
inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage.
ksoftirqd/0/7 [HC0[0]:SC1[3]:HE1:SE0] takes: bf00e014 (list_lock){+.?.}-{2:2}, at: omap_aes_find_dev+0x18/0x54 [omap_aes_driver]
{SOFTIRQ-ON-W} state was registered at:
_raw_spin_lock+0x40/0x50
omap_aes_probe+0x1d4/0x664 [omap_aes_driver]
platform_probe+0x58/0xb8
really_probe+0xbc/0x314
__driver_probe_device+0x80/0xe4
driver_probe_device+0x30/0xc8
__driver_attach+0x70/0xf4
bus_for_each_dev+0x70/0xb4
bus_add_driver+0xf0/0x1d4
driver_register+0x74/0x108
do_one_initcall+0x84/0x2e4
do_init_module+0x5c/0x240
load_module+0x221c/0x2584
sys_finit_module+0xb0/0xec
ret_fast_syscall+0x0/0x2c
0xbed90b30
irq event stamp: 111800
hardirqs last enabled at (111800): [<c02a21e4>] __kmalloc+0x484/0x5ec
hardirqs last disabled at (111799): [<c02a21f0>] __kmalloc+0x490/0x5ec
softirqs last enabled at (111776): [<c01015f0>] __do_softirq+0x2b8/0x4d0
softirqs last disabled at (111781): [<c0135948>] run_ksoftirqd+0x34/0x50
other info that might help us debug this:
Possible unsafe locking scenario:
The loop on entry of ata_host_start() may not initialize host->ops to a
non NULL value. The test on the host_stop field of host->ops must then
be preceded by a check that host->ops is not NULL.
Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Link: https://lore.kernel.org/r/20210816014456.2191776-3-damien.lemoal@wdc.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Tests showed a mismatch between what the CCA tool reports about
the APKA master key state and what's displayed by the zcrypt dd
in sysfs. After some investigation, we found out that the
documentation which was the source for the zcrypt dd implementation
lacks the listing of 3 fields. So this patch now moves the
evaluation of the APKA master key state to the correct offset.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Introduce dev_busid, which exports the device-id associated with the
io-subchannel (and message-subchannel). The dev_busid indicates that of
the device which may be physically installed on the corrosponding
subchannel. The dev_busid value "none" indicates that the subchannel
is not valid, there is no I/O device currently associated with the
subchannel.
The dev_busid information would be helpful to write device-specific
udev-rules associated with the subchannel. The dev_busid interface would
be available even when the sch is not bound to any driver or if there is
no operational device connected on it. Hence this attribute can be used to
write udev-rules which are specific to the device associated with the
subchannel.
Pin control needs to be activated by setting the enable bit, otherwise
hardware rejects all pin changes. Previously this stayed unnoticed on
Nexus 7 because pin control was enabled by default after rebooting from
downstream kernel, which uses driver that enables the bit and charger
registers are non-volatile until power supply (battery) is disconnected.
Configure the pin control enable bit. This fixes the potentially
never-enabled charging on devices that use pin control.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
According to the NVMe specification, the response dword 0 value of the
Connect command is based on status code: return cntlid for successful
compeltion return IPO and IATTR for connect invalid parameters. Fix
a missing error information for a zero sized queue, and return the
cntlid also for I/O queue Connect commands.
Signed-off-by: Amit Engel <amit.engel@dell.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
We update ctrl->queue_count and schedule another reconnect when io queue
count is zero.But we will never try to create any io queue in next reco-
nnection, because ctrl->queue_count already set to zero.We will end up
having an admin-only session in Live state, which is exactly what we try
to avoid in the original patch.
Update ctrl->queue_count after queue_count zero checking to fix it.
Signed-off-by: Ruozhu Li <liruozhu@huawei.com> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
We update ctrl->queue_count and schedule another reconnect when io queue
count is zero.But we will never try to create any io queue in next reco-
nnection, because ctrl->queue_count already set to zero.We will end up
having an admin-only session in Live state, which is exactly what we try
to avoid in the original patch.
Update ctrl->queue_count after queue_count zero checking to fix it.
Signed-off-by: Ruozhu Li <liruozhu@huawei.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
After patch 54efd50 (block: make generic_make_request handle
arbitrarily sized bios), the IO through io-throttle may be larger,
and these IOs may be further split into more small IOs. However,
IOPS throttle does not seem to be aware of this change, which
makes the calculation of IOPS of large IOs incomplete, resulting
in disk-side IOPS that does not meet expectations. Maybe we should
fix this problem.
We can reproduce it by set max_sectors_kb of disk to 128, set
blkio.write_iops_throttle to 100, run a dd instance inside blkio
and use iostat to watch IOPS:
Currently iocharset=utf8 mount option is broken. To use UTF-8 as iocharset,
it is required to use utf8 mount option.
Fix iocharset=utf8 mount option to use be equivalent to the utf8 mount
option.
If UTF-8 as iocharset is used then s_nls_iocharset is set to NULL. So
simplify code around, remove s_utf8 field as to distinguish between UTF-8
and non-UTF-8 it is needed just to check if s_nls_iocharset is set to NULL
or not.
Link: https://lore.kernel.org/r/20210808162453.1653-5-pali@kernel.org Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Currently iocharset=utf8 mount option is broken. To use UTF-8 as iocharset,
it is required to use utf8 mount option.
Fix iocharset=utf8 mount option to use be equivalent to the utf8 mount
option.
If UTF-8 as iocharset is used then s_nls_map is set to NULL. So simplify
code around, remove UDF_FLAG_NLS_MAP and UDF_FLAG_UTF8 flags as to
distinguish between UTF-8 and non-UTF-8 it is needed just to check if
s_nls_map set to NULL or not.
Link: https://lore.kernel.org/r/20210808162453.1653-4-pali@kernel.org Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
We were checking validity of LVID entries only when getting
implementation use information from LVID in udf_sb_lvidiu(). However if
the LVID is suitably corrupted, it can cause problems also to code such
as udf_count_free() which doesn't use udf_sb_lvidiu(). So check validity
of LVID already when loading it from the disk and just disable LVID
altogether when it is not valid.
Reported-by: syzbot+7fbfe5fed73ebb675748@syzkaller.appspotmail.com Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
If high resolution timers are disabled the timerfd notification about a
clock was set event is not happening for all cases which use
clock_was_set_delayed() because that's a NOP for HIGHRES=n, which is wrong.
Make clock_was_set_delayed() unconditially available to fix that.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lore.kernel.org/r/20210713135158.196661266@linutronix.de Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
If __hrtimer_start_range_ns() is invoked with an already armed hrtimer then
the timer has to be canceled first and then added back. If the timer is the
first expiring timer then on removal the clockevent device is reprogrammed
to the next expiring timer to avoid that the pending expiry fires needlessly.
If the new expiry time ends up to be the first expiry again then the clock
event device has to reprogrammed again.
Avoid this by checking whether the timer is the first to expire and in that
case, keep the timer on the current CPU and delay the reprogramming up to
the point where the timer has been enqueued again.
Reported-by: Lorenzo Colitti <lorenzo@google.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lore.kernel.org/r/20210713135157.873137732@linutronix.de Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Hypervisors likely do not expose the SMCA feature to the guest and
loading this module leads to false warnings. This module should not be
loaded in guests to begin with, but people tend to do so, especially
when testing kernels in VMs. And then they complain about those false
warnings.
Do the practical thing and do not load this module when running as a
guest to avoid all that complaining.
The soft watchdog timer function checks if a virtual machine
was suspended and hence what looks like a lockup in fact
is a false positive.
This is what kvm_check_and_clear_guest_paused() does: it
tests guest PVCLOCK_GUEST_STOPPED (which is set by the host)
and if it's set then we need to touch all watchdogs and bail
out.
Watchdog timer function runs from IRQ, so PVCLOCK_GUEST_STOPPED
check works fine.
There is, however, one more watchdog that runs from IRQ, so
watchdog timer fn races with it, and that watchdog is not aware
of PVCLOCK_GUEST_STOPPED - RCU stall detector.
This triggers RCU stalls on our devices during VM resume.
If tick_sched_handle()->rcu_sched_clock_irq() runs on a VCPU
before watchdog_timer_fn()->kvm_check_and_clear_guest_paused()
then there is nothing on this VCPU that touches watchdogs and
RCU reads stale gp stall timestamp and new jiffies value, which
makes it think that RCU has stalled.
Make RCU stall watchdog aware of PVCLOCK_GUEST_STOPPED and
don't report RCU stalls when we resume the VM.
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org> Signed-off-by: Signed-off-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
We should not clear FLAGS_DMA_ACTIVE before omap_sham_update_dma_stop() is
done calling dma_unmap_sg(). We already clear FLAGS_DMA_ACTIVE at the
end of omap_sham_update_dma_stop().
The early clearing of FLAGS_DMA_ACTIVE is not causing issues as we do not
need to defer anything based on FLAGS_DMA_ACTIVE currently. So this can be
applied as clean-up.
Cc: Lokesh Vutla <lokeshvutla@ti.com> Cc: Tero Kristo <kristo@kernel.org> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
When fuel_gauge_reg_readb()/_writeb() fails, report which register we
were trying to read / write when the error happened.
Also reword the message a bit:
- Drop the axp288 prefix, dev_err() already prints this
- Switch from telegram / abbreviated style to a normal sentence, aligning
the message with those from fuel_gauge_read_*bit_word()
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
It is possible for sched_getattr() to incorrectly report the state of
the reset_on_fork flag when called on a deadline task.
Indeed, if the flag was set on a deadline task using sched_setattr()
with flags (SCHED_FLAG_RESET_ON_FORK | SCHED_FLAG_KEEP_PARAMS), then
p->sched_reset_on_fork will be set, but __setscheduler() will bail out
early, which means that the dl_se->flags will not get updated by
__setscheduler_params()->__setparam_dl(). Consequently, if
sched_getattr() is then called on the task, __getparam_dl() will
override kattr.sched_flags with the now out-of-date copy in dl_se->flags
and report the stale value to userspace.
To fix this, make sure to only copy the flags that are relevant to
sched_deadline to and from the dl_se->flags field.
After calling dma_map_single(), we must also call dma_mapping_error().
This fixes the following warning when compiling with CONFIG_DMA_API_DEBUG:
[ 311.241478] WARNING: CPU: 0 PID: 428 at kernel/dma/debug.c:1027 check_unmap+0x79c/0x96c
[ 311.249547] DMA-API: mxs-dcp 2280000.crypto: device driver failed to check map error[device address=0x00000000860cb080] [size=32 bytes] [mapped as single]
Signed-off-by: Sean Anderson <sean.anderson@seco.com> Reviewed-by: Richard Weinberger <richard@nod.at> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
To fix the keyboard issue, add a DMI-based override check that will
not affect other machines along the lines of prt_quirks[] in
drivers/acpi/pci_irq.c.
If similar issues are seen on other platforms, the quirk table could
be expanded in the future.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=213031 BugLink: http://bugs.launchpad.net/bugs/1909814 Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Reported-by: Manuel Krause <manuelkrause@netscape.net> Tested-by: Manuel Krause <manuelkrause@netscape.net> Signed-off-by: Hui Wang <hui.wang@canonical.com>
[ rjw: Subject and changelog edits ] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
(cherry picked from commit 892a012699fc0b91a2ed6309078936191447f480 linux-next) Signed-off-by: Hui Wang <hui.wang@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Adrian Bunk [Fri, 1 Oct 2021 02:20:00 +0000 (04:20 +0200)]
bnx2x: Fix enabling network interfaces without VFs
BugLink: https://bugs.launchpad.net/bugs/1945707
This function is called to enable SR-IOV when available,
not enabling interfaces without VFs was a regression.
Fixes: 65161c35554f ("bnx2x: Fix missing error code in bnx2x_iov_init_one()") Signed-off-by: Adrian Bunk <bunk@kernel.org> Reported-by: YunQiang Su <wzssyqa@gmail.com> Tested-by: YunQiang Su <wzssyqa@gmail.com> Cc: stable@vger.kernel.org Acked-by: Shai Malin <smalin@marvell.com> Link: https://lore.kernel.org/r/20210912190523.27991-1-bunk@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
(cherry picked from commit 52ce14c134a003fee03d8fc57442c05a55b53715) Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Ville Syrjälä [Tue, 28 Sep 2021 18:51:05 +0000 (21:51 +0300)]
drm/i915: Stop force enabling pipe bottom color gammma/csc
BugLink: https://bugs.launchpad.net/bugs/1945932
While sanitizing the hardware state we're currently forcing
the pipe bottom color legacy csc/gamma bits on. That is not a
good idea as BIOSen are likely to leave gabage in the LUTs and
so doing this causes ugly visual glitches if and when the
planes covering the background get disabled. This was exactly
the case on this Dell Precision 5560 tgl laptop.
On icl+ we don't normally even use these legacy bits
anymore and instead use their GAMMA_MODE counterparts.
On earlier platforms the bits are used, but we still
shouldn't force them on without knowing what's in the LUT.
So two options, get rid of the whole thing, or do what
intel_color_commit() does to make sure the bottom color state
matches whatever out hardware readout produced. I chose the
latter since it'll match what happens on older platforms when
the primary plane gets turned off. In fact let's just call
intel_color_commit(). It'll also do some CSC programming but
since we don't have readout for that it'll actually just set
to all zeros. So in the unlikely case of CSC actually being
enabld by the BIOS we'll end up with all black until the first
atomic commit happens.
Still not totally sure what we should do about color management
features here in general. Probably the safest thing would be to
force everything off exactly at the same time when we disable
the primary plane as there is no guarantees that whatever the
LUTs/CSCs contain make any sense whatsoever without the
specific pixel data in the BIOS fb. And if we preserve the
primary plane then we should disable the color management
features exactly when the primary plane fb contents first
changes since the new content assumes more or less no
transformations. But of course synchronizing front buffer
rendering with anything else is a bit hard...
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/3534 Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210928185105.3030-1-ville.syrjala@linux.intel.com Reviewed-by: Uma Shankar <uma.shankar@intel.com>
(backported from commit f22f4e5be89c4296d76eaa9ba83dda46bdf11134i linux-next) Signed-off-by: Koba Ko <koba.ko@canonical.com>
[backport: s/DISPLAY_VER/INTEL_GEN/] Acked-by: Tim Gardner <tim.gardner@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When this platform was relatively new in November 2011, with early BIOS
revisions, a reboot quirk was added in commit 6be30bb7d750 ("x86/reboot:
Blacklist Dell OptiPlex 990 known to require PCI reboot")
However, this quirk (and several others) are open-ended to all BIOS
versions and left no automatic expiry if/when the system BIOS fixed the
issue, meaning that nobody is likely to come along and re-test.
What is really problematic with using PCI reboot as this quirk does, is
that it causes this platform to do a full power down, wait one second,
and then power back on. This is less than ideal if one is using it for
boot testing and/or bisecting kernels when legacy rotating hard disks
are installed.
It was only by chance that the quirk was noticed in dmesg - and when
disabled it turned out that it wasn't required anymore (BIOS A24), and a
default reboot would work fine without the "harshness" of power cycling the
machine (and disks) down and up like the PCI reboot does.
Doing a bit more research, it seems that the "newest" BIOS for which the
issue was reported[1] was version A06, however Dell[2] seemed to suggest
only up to and including version A05, with the A06 having a large number of
fixes[3] listed.
As is typical with a new platform, the initial BIOS updates come frequently
and then taper off (and in this case, with a revival for CPU CVEs); a
search for O990-A<ver>.exe reveals the following dates:
A02 16 Mar 2011
A03 11 May 2011
A06 14 Sep 2011
A07 24 Oct 2011
A10 08 Dec 2011
A14 06 Sep 2012
A16 15 Oct 2012
A18 30 Sep 2013
A19 23 Sep 2015
A20 02 Jun 2017
A23 07 Mar 2018
A24 21 Aug 2018
While it's overkill to flash and test each of the above, it would seem
likely that the issue was contained within A0x BIOS versions, given the
dates above and the dates of issue reports[4] from distros. So rather than
just throw out the quirk entirely, limit the scope to just those early BIOS
versions, in case people are still running systems from 2011 with the
original as-shipped early A0x BIOS versions.
Removes static char buffer usage in the following decode functions:
xhci_decode_trb()
xhci_decode_ptortsc()
Caller must provide a buffer to use.
In tracing use __get_str() as recommended to pass buffer.
Minor chanes are needed in xhci debugfs code as these functions are also
used there. Changes include moving XHCI_MSG_MAX definititon from
xhci-trace.h to xhci.h
Cc: <stable@vger.kernel.org> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20210820123503.2605901-2-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Removes static char buffer usage in the following decode functions:
xhci_decode_ctrl_ctx()
xhci_decode_slot_context()
xhci_decode_usbsts()
xhci_decode_doorbell()
xhci_decode_ep_context()
Caller must provide a buffer to use.
In tracing use __get_str() as recommended to pass buffer.
Minor changes are needed in other xhci code as these functions are also
used elsewhere
Cc: <stable@vger.kernel.org> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20210820123503.2605901-3-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
usb_endpoint_maxp() only returns the bit[10:0] of wMaxPacketSize
of endpoint descriptor, not includes bit[12:11] anymore, so use
usb_endpoint_maxp_mult() instead.
Meanwhile no need AND 0x7ff when get maxp, remove it.
Fixes: 49db427232fe ("usb: gadget: Add UDC driver for tegra XUSB device mode controller") Cc: stable@vger.kernel.org Acked-by: Felipe Balbi <balbi@kernel.org> Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> Link: https://lore.kernel.org/r/1628836253-7432-5-git-send-email-chunfeng.yun@mediatek.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
According to the datasheet, "Upon the completion of FW Download,
there is no need to write or reload FW.". Otherwise, it's possible
to cause unexpected behaviors. So, adds such a condition.
Fixes: 4ac8918f3a73 ("usb: host: xhci-plat: add support for the R-Car H2 and M2 xHCI controllers") Cc: stable@vger.kernel.org # v3.17+ Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Link: https://lore.kernel.org/r/20210827063227.81990-1-yoshihiro.shimoda.uh@renesas.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Before we free request queue, clearing flush request reference in
tags->rqs[], so that potential UAF can be avoided.
Based on one patch written by David Jeffery.
Tested-by: John Garry <john.garry@huawei.com> Reviewed-by: Bart Van Assche <bvanassche@acm.org> Reviewed-by: David Jeffery <djeffery@redhat.com> Signed-off-by: Ming Lei <ming.lei@redhat.com> Link: https://lore.kernel.org/r/20210511152236.763464-5-ming.lei@redhat.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
For fixing use-after-free during iterating over requests, we grabbed
request's refcount before calling ->fn in commit 2e315dc07df0 ("blk-mq:
grab rq->refcount before calling ->fn in blk_mq_tagset_busy_iter").
Turns out this way may cause kernel panic when iterating over one flush
request:
1) old flush request's tag is just released, and this tag is reused by
one new request, but ->rqs[] isn't updated yet
2) the flush request can be re-used for submitting one new flush command,
so blk_rq_init() is called at the same time
3) meantime blk_mq_queue_tag_busy_iter() is called, and old flush request
is retrieved from ->rqs[tag]; when blk_mq_put_rq_ref() is called,
flush_rq->end_io may not be updated yet, so NULL pointer dereference
is triggered in blk_mq_put_rq_ref().
Fix the issue by calling refcount_set(&flush_rq->ref, 1) after
flush_rq->end_io is set. So far the only other caller of blk_rq_init() is
scsi_ioctl_reset() in which the request doesn't enter block IO stack and
the request reference count isn't used, so the change is safe.
Fixes: 2e315dc07df0 ("blk-mq: grab rq->refcount before calling ->fn in blk_mq_tagset_busy_iter") Reported-by: "Blank-Burian, Markus, Dr." <blankburian@uni-muenster.de> Tested-by: "Blank-Burian, Markus, Dr." <blankburian@uni-muenster.de> Signed-off-by: Ming Lei <ming.lei@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: John Garry <john.garry@huawei.com> Link: https://lore.kernel.org/r/20210811142624.618598-1-ming.lei@redhat.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Cc: Yi Zhang <yi.zhang@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
On certain AMD platforms, when the IOMMU performance counter source
(csource) field is zero, power-gating for the counter is enabled, which
prevents write access and returns zero for read access.
This can cause invalid perf result especially when event multiplexing
is needed (i.e. more number of events than available counters) since
the current logic keeps track of the previously read counter value,
and subsequently re-program the counter to continue counting the event.
With power-gating enabled, we cannot gurantee successful re-programming
of the counter.
Workaround this issue by :
1. Modifying the ordering of setting/reading counters and enabing/
disabling csources to only access the counter when the csource
is set to non-zero.
2. Since AMD IOMMU PMU does not support interrupt mode, the logic
can be simplified to always start counting with value zero,
and accumulate the counter value when stopping without the need
to keep track and reprogram the counter with the previously read
counter value.
This has been tested on systems with and without power-gating.
Fixes: 994d6608efe4 ("iommu/amd: Remove performance counter pre-initialization test") Suggested-by: Alexander Monakov <amonakov@ispras.ru> Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lkml.kernel.org/r/20210504065236.4415-1-suravee.suthikulpanit@amd.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
This is used to re-enable ASPM on RTL8106e, if it is possible.
Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
As was concluded in a follow-up discussion of commit e0efb3168d34 (tty:
Remove dead termiox code) [1], termiox ioctls never worked, so there is
barely anyone using this interface. We can safely remove the user
definitions for this never adopted interface.
projects / mirror_ubuntu-hirsute-kernel.git / log