Will Deacon [Thu, 5 Jan 2017 18:38:26 +0000 (18:38 +0000)]
iommu: Allow default domain type to be set on the kernel command line
The IOMMU core currently initialises the default domain for each group
to IOMMU_DOMAIN_DMA, under the assumption that devices will use
IOMMU-backed DMA ops by default. However, in some cases it is desirable
for the DMA ops to bypass the IOMMU for performance reasons, reserving
use of translation for subsystems such as VFIO that require it for
enforcing device isolation.
Rather than modify each IOMMU driver to provide different semantics for
DMA domains, instead we introduce a command line parameter that can be
used to change the type of the default domain. Passthrough can then be
specified using "iommu.passthrough=1" on the kernel command line.
BugLink: http://bugs.launchpad.net/bugs/1688158 Signed-off-by: Will Deacon <will.deacon@arm.com>
(cherry picked from commit fccb4e3b8ab0957628abec82675691c72f67003e) Signed-off-by: Manoj Iyer <manoj.iyer@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Will Deacon [Fri, 6 Jan 2017 16:27:30 +0000 (16:27 +0000)]
iommu/arm-smmu-v3: Install bypass STEs for IOMMU_DOMAIN_IDENTITY domains
In preparation for allowing the default domain type to be overridden,
this patch adds support for IOMMU_DOMAIN_IDENTITY domains to the
ARM SMMUv3 driver.
An identity domain is created by placing the corresponding stream table
entries into "bypass" mode, which allows transactions to flow through
the SMMU without any translation.
BugLink: http://bugs.launchpad.net/bugs/1688158 Signed-off-by: Will Deacon <will.deacon@arm.com>
(cherry picked from commit beb3c6a066bff1ba412f983cb9d1a42f4cd8f76a) Signed-off-by: Manoj Iyer <manoj.iyer@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Joerg Roedel [Wed, 1 Feb 2017 15:56:46 +0000 (16:56 +0100)]
iommu: Add sysfs bindings for struct iommu_device
There is currently support for iommu sysfs bindings, but
those need to be implemented in the IOMMU drivers. Add a
more generic version of this by adding a struct device to
struct iommu_device and use that for the sysfs bindings.
Also convert the AMD and Intel IOMMU driver to make use of
it.
BugLink: http://bugs.launchpad.net/bugs/1688158 Signed-off-by: Joerg Roedel <jroedel@suse.de>
(cherry picked from commit 39ab9555c24110671f8dc671311a26e5c985b592) Signed-off-by: Manoj Iyer <manoj.iyer@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Joerg Roedel [Wed, 1 Feb 2017 12:23:08 +0000 (13:23 +0100)]
iommu: Introduce new 'struct iommu_device'
This struct represents one hardware iommu in the iommu core
code. For now it only has the iommu-ops associated with it,
but that will be extended soon.
The register/unregister interface is also added, as well as
making use of it in the Intel and AMD IOMMU drivers.
BugLink: http://bugs.launchpad.net/bugs/1688158 Signed-off-by: Joerg Roedel <jroedel@suse.de>
(cherry picked from commit b0119e870837dcd15a207b4701542ebac5d19b45) Signed-off-by: Manoj Iyer <manoj.iyer@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Joerg Roedel [Wed, 1 Feb 2017 11:19:46 +0000 (12:19 +0100)]
iommu: Rename struct iommu_device
The struct is used to link devices to iommu-groups, so
'struct group_device' is a better name. Further this makes
the name iommu_device available for a struct representing
hardware iommus.
BugLink: http://bugs.launchpad.net/bugs/1688158 Signed-off-by: Joerg Roedel <jroedel@suse.de>
(cherry picked from commit c09e22d5370739e16463c113525df51b5980b1d5) Signed-off-by: Manoj Iyer <manoj.iyer@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Joerg Roedel [Tue, 31 Jan 2017 15:58:42 +0000 (16:58 +0100)]
iommu: Rename iommu_get_instance()
Rename the function to iommu_ops_from_fwnode(), because that
is what the function actually does. The new name is much
more descriptive about what the function does.
BugLink: http://bugs.launchpad.net/bugs/1688158 Signed-off-by: Joerg Roedel <jroedel@suse.de>
(cherry picked from commit 534766dfef999f7e7349bbd91cd19c1673792af3) Signed-off-by: Manoj Iyer <manoj.iyer@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Will Deacon [Wed, 1 Mar 2017 21:11:29 +0000 (21:11 +0000)]
iommu/arm-smmu-v3: Make arm_smmu_install_ste_for_dev return void
arm_smmu_install_ste_for_dev cannot fail and always returns 0, however
the fact that it returns int means that callers end up implementing
redundant error handling code which complicates STE tracking and is
never executed.
This patch changes the return type of arm_smmu_install_ste_for_dev
to void, to make it explicit that it cannot fail.
BugLink: http://bugs.launchpad.net/bugs/1688158 Signed-off-by: Will Deacon <will.deacon@arm.com>
(cherry picked from commit 67560edcd8e5c57eccec4df562abbfc21c17ad75) Signed-off-by: Manoj Iyer <manoj.iyer@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Will Deacon [Fri, 6 Jan 2017 16:56:03 +0000 (16:56 +0000)]
iommu/arm-smmu: Install bypass S2CRs for IOMMU_DOMAIN_IDENTITY domains
In preparation for allowing the default domain type to be overridden,
this patch adds support for IOMMU_DOMAIN_IDENTITY domains to the
ARM SMMU driver.
An identity domain is created by placing the corresponding S2CR
registers into "bypass" mode, which allows transactions to flow through
the SMMU without any translation.
BugLink: http://bugs.launchpad.net/bugs/1688158 Reviewed-by: Robin Murphy <robin.murphy@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
(cherry picked from commit 61bc671179f19060be883068b6d3d82ae0b24bc0) Signed-off-by: Manoj Iyer <manoj.iyer@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Will Deacon [Fri, 6 Jan 2017 16:28:17 +0000 (16:28 +0000)]
iommu/arm-smmu: Restrict domain attributes to UNMANAGED domains
The ARM SMMU drivers provide a DOMAIN_ATTR_NESTING domain attribute,
which allows callers of the IOMMU API to request that the page table
for a domain is installed at stage-2, if supported by the hardware.
Since setting this attribute only makes sense for UNMANAGED domains,
this patch returns -ENODEV if the domain_{get,set}_attr operations are
called on other domain types.
BugLink: http://bugs.launchpad.net/bugs/1688158 Signed-off-by: Will Deacon <will.deacon@arm.com>
(cherry picked from commit 0834cc28fa56c65887c614b6c045be2ba06fdcb0) Signed-off-by: Manoj Iyer <manoj.iyer@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Willy Tarreau [Wed, 7 Jun 2017 09:05:21 +0000 (17:05 +0800)]
char: lp: fix possible integer overflow in lp_setup()
CVE-2017-100363
The lp_setup() code doesn't apply any bounds checking when passing
"lp=none", and only in this case, resulting in an overflow of the
parport_nr[] array. All versions in Git history are affected.
Reported-By: Roee Hay <roee.hay@hcl.com> Cc: Ben Hutchings <ben@decadent.org.uk> Cc: stable@vger.kernel.org Signed-off-by: Willy Tarreau <w@1wt.eu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 3e21f4af170bebf47c187c1ff8bf155583c9f3b1)
Signed-off-by: Po-Hsu Lin <po-hsu.lin@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
The skb_copy_and_csum_bits(skb_prev, maxfraglen, data + transhdrlen,
fraggap, 0); is overwriting skb->head and skb_shared_info
Since we apparently detect this rare condition too late, move the
code earlier to even avoid allocating skb and risking crashes.
Once again, many thanks to Andrey and syzkaller team.
Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Andrey Konovalov <andreyknvl@google.com> Tested-by: Andrey Konovalov <andreyknvl@google.com> Reported-by: <idaifish@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
CVE-2017-9242
(cherry-picked from 232cd35d0804cc241eb887bb8d4d9b3b9881c64a) Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Colin King <colin.king@canonical.com> Acked-by: Andy Whitcroft <andy.whitcroft@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Eric Dumazet [Wed, 17 May 2017 14:16:40 +0000 (07:16 -0700)]
sctp: do not inherit ipv6_{mc|ac|fl}_list from parent
SCTP needs fixes similar to 83eaddab4378 ("ipv6/dccp: do not inherit
ipv6_mc_list from parent"), otherwise bad things can happen.
Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Andrey Konovalov <andreyknvl@google.com> Tested-by: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
CVE-2017-9075
(cherry-picked from fdcee2cbb8438702ea1b328fb6e0ac5e9a40c7f8) Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Colin King <colin.king@canonical.com> Acked-by: Andy Whitcroft <andy.whitcroft@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Craig Gallek [Tue, 16 May 2017 18:36:23 +0000 (14:36 -0400)]
ipv6: Prevent overrun when parsing v6 header options
The KASAN warning repoted below was discovered with a syzkaller
program. The reproducer is basically:
int s = socket(AF_INET6, SOCK_RAW, NEXTHDR_HOP);
send(s, &one_byte_of_data, 1, MSG_MORE);
send(s, &more_than_mtu_bytes_data, 2000, 0);
The socket() call sets the nexthdr field of the v6 header to
NEXTHDR_HOP, the first send call primes the payload with a non zero
byte of data, and the second send call triggers the fragmentation path.
The fragmentation code tries to parse the header options in order
to figure out where to insert the fragment option. Since nexthdr points
to an invalid option, the calculation of the size of the network header
can made to be much larger than the linear section of the skb and data
is read outside of it.
This fix makes ip6_find_1stfrag return an error if it detects
running out-of-bounds.
Reported-by: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: Craig Gallek <kraig@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
CVE-2017-9074
(cherry-picked from 2423496af35d94a87156b063ea5cedffc10a70a1) Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Colin King <colin.king@canonical.com> Acked-by: Andy Whitcroft <andy.whitcroft@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
WANG Cong [Wed, 7 Jun 2017 10:28:27 +0000 (12:28 +0200)]
ipv6/dccp: do not inherit ipv6_mc_list from parent
Like commit 657831ffc38e ("dccp/tcp: do not inherit mc_list from parent")
we should clear ipv6_mc_list etc. for IPv6 sockets too.
Cc: Eric Dumazet <edumazet@google.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
CVE-2017-9076
CVE-2017-9077
(cherry-picked from 83eaddab4378db256d00d295bda6ca997cd13a52) Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Colin Ian King <colin.king@canonical.com> Acked-by: Andy Whitcroft <apw@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Eric Dumazet [Tue, 6 Jun 2017 16:16:00 +0000 (18:16 +0200)]
dccp/tcp: do not inherit mc_list from parent
syzkaller found a way to trigger double frees from ip_mc_drop_socket()
It turns out that leave a copy of parent mc_list at accept() time,
which is very bad.
Very similar to commit 8b485ce69876 ("tcp: do not inherit
fastopen_req from parent")
Initial report from Pray3r, completed by Andrey one.
Thanks a lot to them !
Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Pray3r <pray3r.z@gmail.com> Reported-by: Andrey Konovalov <andreyknvl@google.com> Tested-by: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
CVE-2017-8890
(cherry-picked from 657831ffc38e30092a2d5f03d385d710eb88b09a) Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Colin Ian King <colin.king@canonical.com> Acked-by: Andy Whitcroft <apw@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Seth Forshee [Mon, 15 May 2017 20:37:56 +0000 (15:37 -0500)]
UBUNTU: SAUCE: Fix module signing exclusion in package builds
BugLink: http://bugs.launchpad.net/bugs/1690908
The current module signing exclusion implementation suffers from
two problems. First, it looks for the signed-inclusion file
relative to the path where make is executed and thus doesn't work
if the source and build directories are different. Second, the
signed-inclusion file lists only the module name, but the strings
searched for in the file include the path (and the path to the
module install location at that).
Fix these problems by updating scripts/Makefile.modinst to look
for signed-inclusion relative to the path of the source tree and
to use only the module name when matching against the contents of
that file.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com> Acked-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
BugLink: http://bugs.launchpad.net/bugs/1693504
gen-auto-reconstruct script adds extend-diff-ignore options to
debian/source/options for symlinks not found in the orig tarball.
These options, however, are regular expressions, and match any part of a
file path. This may cause some files to be excluded from source when
they are not an exact match, but are a partial match to those symlinks.
Using beggining and end of string metacharacters fix the issue.
This problem was found in one of the derivatives, which contained a
symlink, whose name was a prefix for a directory in the same path,
leading that entire directory to be excluded from source.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
[saf: escape literal '$' in string] Acked-by: Andy Whitcroft <apw@canonical.com> Signed-off-by: Seth Forshee <seth.forshee@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Ard Biesheuvel [Tue, 30 May 2017 16:35:40 +0000 (10:35 -0600)]
drivers/tty: 8250: only call fintek_8250_probe when doing port I/O
BugLink: https://bugs.launchpad.net/bugs/1692548
Commit fa01e2ca9f53 ("serial: 8250: Integrate Fintek into 8250_base")
modified the probing logic for PNP0501 devices, to remove a collision
between the generic 16550A driver and the Fintek driver, which reused
the same ACPI _HID.
The Fintek device probe is now incorporated into the common 8250 probe
path, and gets called for all discovered 16550A compatible devices,
including ones that are MMIO mapped rather than IO mapped. However,
the Fintek driver assumes the port base is a I/O address, and proceeds
to probe some arbitrary offsets above it.
This is generally a wrong thing to do, but on ARM systems (having no
native port I/O), this may result in faulting accesses of completely
unrelated MMIO regions in the PCI I/O space. Given that this is at
serial probe time, this results in hard to diagnose crashes at boot.
So let's restrict the Fintek probe to devices that we know are using
port I/O in the first place.
Fixes: fa01e2ca9f53 ("serial: 8250: Integrate Fintek into 8250_base") Suggested-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Ricardo Ribalda <ricardo.ribalda@gmail.com> Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 4c4fc90964b1cf205a67df566cc82ea1731bcb00) Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Colin King <colin.king@canonical.com> Acked-by: Seth Forshee <seth.forshee@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Sunil Goutham [Tue, 30 May 2017 18:15:35 +0000 (12:15 -0600)]
net: thunderx: Fix IOMMU translation faults
BugLink: https://bugs.launchpad.net/bugs/1694506
ACPI support has been added to ARM IOMMU driver in 4.10 kernel
and that has resulted in VNIC interfaces throwing translation
faults when kernel is booted with ACPI as driver was not using
DMA API. This patch fixes the issue by using DMA API which inturn
will create translation tables when IOMMU is enabled.
Also VNIC doesn't have a seperate receive buffer ring per receive
queue, so there is no 1:1 descriptor index matching between CQE_RX
and the index in buffer ring from where a buffer has been used for
DMA'ing. Unlike other NICs, here it's not possible to maintain dma
address to virt address mappings within the driver. This leaves us
no other choice but to use IOMMU's IOVA address conversion API to
get buffer's virtual address which can be given to network stack
for processing.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
(cherry picked from commit 83abb7d7c91f4ac20e47c3089a10bb93b2ea8994) Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Colin King <colin.king@canonical.com> Acked-by: Seth Forshee <seth.forshee@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
This is wrong because the clear register array includes the reserved
interrupts. So the clear operation ends up in the wrong register.
This went unnoticed so far, because the hardware clears the real bit
through a timeout mechanism when the hardware is configured in debug
mode. That debug mode was enabled on early generations of the hardware, so
the problem was papered over.
On newer hardware with updated firmware the debug mode was disabled, so the
bits did not get cleared which causes the system to malfunction.
Remove the subtraction of RESERVED_IRQ_PER_MBIGEN_CHIP, so the correct
register is accessed.
[ tglx: Rewrote changelog ]
Fixes: a6c2f87b8820 ("irqchip/mbigen: Implement the mbigen irq chip operation functions") Signed-off-by: MaJun <majun258@huawei.com> Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org> Acked-by: Marc Zyngier <marc.zyngier@arm.com> Cc: Kefeng Wang <wangkefeng.wang@huawei.com> Cc: linuxarm@huawei.com Cc: Wei Yongjun <weiyongjun1@huawei.com> Link: http://lkml.kernel.org/r/1494561328-39514-4-git-send-email-guohanjun@huawei.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
(cherry picked from commit 9459a04b6a5a09967eec94a1b66f0a74312819d9) Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Colin King <colin.king@canonical.com> Acked-by: Seth Forshee <seth.forshee@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Hanjun Guo [Fri, 12 May 2017 03:55:26 +0000 (11:55 +0800)]
irqchip/mbigen: Fix memory mapping code
BugLink: https://bugs.launchpad.net/bugs/1692783
Some mbigens share memory regions, and devm_ioremap_resource
does not allow to share resources which will break the probe
of mbigen, in opposition to devm_ioremap.
This patch restores back usage of devm_ioremap function, but
with proper error handling and logging.
Fixes: 216646e4d82e ("irqchip/mbigen: Fix return value check in mbigen_device_probe()") Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org> Acked-by: Marc Zyngier <marc.zyngier@arm.com> Cc: Kefeng Wang <wangkefeng.wang@huawei.com> Cc: linuxarm@huawei.com Cc: Wei Yongjun <weiyongjun1@huawei.com> Cc: MaJun <majun258@huawei.com> Link: http://lkml.kernel.org/r/1494561328-39514-2-git-send-email-guohanjun@huawei.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
(cherry picked from commit 5ba9b0a14132d0b8d97affe909f324045a968d03) Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Colin King <colin.king@canonical.com> Acked-by: Seth Forshee <seth.forshee@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
irqchip/mbigen: Fix return value check in mbigen_device_probe()
BugLink: https://bugs.launchpad.net/bugs/1692783
In case of error, the function devm_ioremap() returns NULL pointer
not ERR_PTR(). Use devm_ioremap_resource() instead of devm_ioremap()
to fix the IS_ERR() test issue.
Fixes: 76e1f77f9c26 ("irqchip/mbigen: Introduce mbigen_of_create_domain()") Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Kefeng Wang <wangkefeng.wang@huawei.com> Cc: Jason Cooper <jason@lakedaemon.net> Link: http://lkml.kernel.org/r/20170427152113.31147-1-weiyj.lk@gmail.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
(backported from commit 216646e4d82e847791f0ba66c439dedd36cb119f) Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Colin King <colin.king@canonical.com> Acked-by: Seth Forshee <seth.forshee@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Hanjun Guo [Tue, 28 Mar 2017 12:21:05 +0000 (20:21 +0800)]
irqchip/mbigen: Add ACPI support
BugLink: https://bugs.launchpad.net/bugs/1692783
With the preparation of platform msi support and interrupt producer
in commit d44fa3d46079 ("ACPI: Add support for ResourceSource/IRQ
domain mapping"), we can add mbigen ACPI support now.
Now that the major framework changes are ready, we just need to add
the ACPI probe code which creates the irqdomain for devices connecting
to it.
In order to create the irqdomain, we need to know the number of hw
irqs as input which is provided by mbigen. In DT case, we are using
"num-pins" property to describe it, and we will take advantage of
that too using _DSD in ACPI as there is no standard way of describe
it in ACPI way, also according to the _DSD rule described in
Documentation/acpi/DSD-properties-rules.txt, it doesn't break
the rules.
So for the devices connected to the mbigen, as we clearly say that
it refers to a specific interrupt controller (mbigen), we can get
the virq from mbigen's irqdomain once it's created successfully.
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org> Signed-off-by: MaJun <majun258@huawei.com> Cc: Al Stone <ahs3@redhat.com> Cc: Darren Hart <dvhart@infradead.org> Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
(cherry picked from commit f907c515ffb06e6fd5e74397badd674f3c233418) Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Colin King <colin.king@canonical.com> Acked-by: Seth Forshee <seth.forshee@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Colin King <colin.king@canonical.com> Acked-by: Seth Forshee <seth.forshee@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Thomas Gleixner [Thu, 1 Jun 2017 05:12:18 +0000 (13:12 +0800)]
pinctrl/amd: Use regular interrupt instead of chained
BugLink: https://bugs.launchpad.net/bugs/1671360
The AMD pinctrl driver uses a chained interrupt to demultiplex the GPIO
interrupts. Kevin Vandeventer reported, that his new AMD Ryzen locks up
hard on boot when the AMD pinctrl driver is initialized. The reason is an
interrupt storm. It's not clear whether that's caused by hardware or
firmware or both.
Using chained interrupts on X86 is a dangerous endavour. If a system is
misconfigured or the hardware buggy there is no safety net to catch an
interrupt storm.
Convert the driver to use a regular interrupt for the demultiplex
handler. This allows the interrupt storm detector to catch the malfunction
and lets the system boot up.
This should be backported to stable because it's likely that more users run
into this problem as the AMD Ryzen machines are spreading.
Reported-by: Kevin Vandeventer Link: https://bugzilla.suse.com/show_bug.cgi?id=1034261 Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
(backported from commit babdc22b0ccf4ef5a3075ce6e4afc26b7a279faf linux-next) Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Seth Forshee <seth.forshee@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/1671360
The amd pinctrl drivers currently implement an irq_chip for handling
interrupts; due to how irq_chip handling is done, it's necessary for the
irq_chip methods to be invoked from hardirq context, even on a a
real-time kernel. Because the spinlock_t type becomes a "sleeping"
spinlock w/ RT kernels, it is not suitable to be used with irq_chips.
A quick audit of the operations under the lock reveal that they do only
minimal, bounded work, and are therefore safe to do under a raw spinlock.
Signed-off-by: Julia Cartwright <julia@ni.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
(cherry picked from commit 229710fecdd805abb753c480778ea0de47cbb1e2) Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Seth Forshee <seth.forshee@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Michael Ellerman [Mon, 29 May 2017 14:54:39 +0000 (11:54 -0300)]
powerpc/powernv: Fix oops on P9 DD1 in cause_ipi()
BugLink: http://bugs.launchpad.net/bugs/1691973
Recently we merged the native xive support for Power9, and then separately some
reworks for doorbell IPI support. In isolation both series were OK, but the
merged result had a bug in one case.
On P9 DD1 we use pnv_p9_dd1_cause_ipi() which tries to use doorbells, and then
falls back to the interrupt controller. However the fallback is implemented by
calling icp_ops->cause_ipi. But now that xive support is merged we might be
using xive, in which case icp_ops is not initialised, it's a xics specific
structure. This leads to an oops such as:
Unable to handle kernel paging request for data at address 0x00000028
Oops: Kernel access of bad area, sig: 11 [#1]
NIP pnv_p9_dd1_cause_ipi+0x74/0xe0
LR smp_muxed_ipi_message_pass+0x54/0x70
To fix it, rather than using icp_ops which might be NULL, have both xics and
xive set smp_ops->cause_ipi, and then in the powernv code we save that as
ic_cause_ipi before overriding smp_ops->cause_ipi. For paranoia add a WARN_ON()
to check if somehow smp_ops->cause_ipi is NULL.
Fixes: b866cc2199d6 ("powerpc: Change the doorbell IPI calling convention") Tested-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
(cherry picked from commit 45b21cfeb22087795f0b49397fbe529efeb99baf) Signed-off-by: Gustavo Walbon <gwalbon@linux.vnet.ibm.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Seth Forshee <seth.forshee@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
BugLink: http://bugs.launchpad.net/bugs/1691973
Some powerpc platforms use this to move IRQs away from a CPU being
unplugged. This function has several bugs such as not taking the right
locks or failing to NULL check pointers.
There's a new generic function doing exactly the same thing without all
the bugs, so let's use it instead.
mpe: The obvious place for the select of GENERIC_IRQ_MIGRATION is on
HOTPLUG_CPU, but that doesn't work. On some configs PM_SLEEP_SMP will
select HOTPLUG_CPU even though its dependencies are not met, which means
the select of GENERIC_IRQ_MIGRATION doesn't happen. That leads to the
build breaking. Fix it by moving the select of GENERIC_IRQ_MIGRATION to
SMP.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
(cherry picked from commit a978e13965a40ac07163643cc3fa0ddb0d354198) Signed-off-by: Gustavo Walbon <gwalbon@linux.vnet.ibm.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Seth Forshee <seth.forshee@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
BugLink: http://bugs.launchpad.net/bugs/1691973
Some platforms (will) need to perform allocations before bringing
a new CPU online. Doing it from smp_ops->setup_cpu is the wrong
thing to do:
- It has no useful failure path (too late)
- Calling any allocator will enable interrupts prematurely
causing problems with large decrementer among others
Instead, add a new callback that is called from __cpu_up (so from
the context trying to online the new CPU) at a point where we
can safely allocate and handle failures.
This will be used by XIVE support.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
(cherry picked from commit 14d4ae5c4cb89c05262fe41cb7a26f6ba949d8df) Signed-off-by: Gustavo Walbon <gwalbon@linux.vnet.ibm.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Seth Forshee <seth.forshee@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Nicholas Piggin [Mon, 29 May 2017 14:54:34 +0000 (11:54 -0300)]
powerpc/powernv: POWER9 support for msgsnd/doorbell IPI
BugLink: http://bugs.launchpad.net/bugs/1691973
POWER9 requires msgsync for receiver-side synchronization, and a DD1
workaround restricts IPIs to core-local.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Drop no longer needed asm feature macro changes] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
(cherry picked from commit 6b3edefefa6752df57ad636f26baa1b0a502ddab) Signed-off-by: Gustavo Walbon <gwalbon@linux.vnet.ibm.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Seth Forshee <seth.forshee@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Nicholas Piggin [Mon, 29 May 2017 14:54:31 +0000 (11:54 -0300)]
powerpc: Change the doorbell IPI calling convention
BugLink: http://bugs.launchpad.net/bugs/1691973
Change the doorbell callers to know about their msgsnd addressing,
rather than have them set a per-cpu target data tag at boot that gets
sent to the cause_ipi functions. The data is only used for doorbell IPI
functions, no other IPI types, so it makes sense to keep that detail
local to doorbell.
Have the platform code understand doorbell IPIs, rather than the
interrupt controller code understand them. Platform code can look at
capabilities it has available and decide which to use.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
(cherry picked from commit b866cc2199d6a6cdcefe4acfe4cfca3ac3c6d38e) Signed-off-by: Gustavo Walbon <gwalbon@linux.vnet.ibm.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Seth Forshee <seth.forshee@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
powerpc/xive: Native exploitation of the XIVE interrupt controller
BugLink: http://bugs.launchpad.net/bugs/1691973
The XIVE interrupt controller is the new interrupt controller
found in POWER9. It supports advanced virtualization capabilities
among other things.
Currently we use a set of firmware calls that simulate the old
"XICS" interrupt controller but this is fairly inefficient.
This adds the framework for using XIVE along with a native
backend which OPAL for configuration. Later, a backend allowing
the use in a KVM or PowerVM guest will also be provided.
This disables some fast path for interrupts in KVM when XIVE is
enabled as these rely on the firmware emulation code which is no
longer available when the XIVE is used natively by Linux.
A latter patch will make KVM also directly exploit the XIVE, thus
recovering the lost performance (and more).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[mpe: Fixup pr_xxx("XIVE:"...), don't split pr_xxx() strings,
tweak Kconfig so XIVE_NATIVE selects XIVE and depends on POWERNV,
fix build errors when SMP=n, fold in fixes from Ben:
Don't call cpu_online() on an invalid CPU number
Fix irq target selection returning out of bounds cpu#
Extra sanity checks on cpu numbers
] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
(cherry picked from commit 243e25112d06b348f087a6f7aba4bbc288285bdd) Signed-off-by: Gustavo Walbon <gwalbon@linux.vnet.ibm.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Seth Forshee <seth.forshee@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Douglas Miller [Mon, 29 May 2017 14:54:29 +0000 (11:54 -0300)]
powerpc/xmon: Dump memory in CPU endian format
BugLink: http://bugs.launchpad.net/bugs/1691973
Extend the dump command to allow display of 2, 4, and 8 byte words in
CPU endian format. Also adds dump command for "1 byte values" for the
sake of symmetry. New commands are:
Nicholas Piggin [Mon, 29 May 2017 14:54:28 +0000 (11:54 -0300)]
powerpc/64s: Add SCV FSCR bit for ISA v3.0
BugLink: http://bugs.launchpad.net/bugs/1691973
Add the bit definition and use it in facility_unavailable_exception() so we can
intelligently report the cause if we take a fault for SCV. This doesn't actually
enable SCV.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Drop whitespace changes to the existing entries, flush out change log] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
(cherry picked from commit 9b7ff0c6586bc0541ebcd1ff6773b11a49f1a058) Signed-off-by: Gustavo Walbon <gwalbon@linux.vnet.ibm.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Seth Forshee <seth.forshee@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Ankit Kumar [Fri, 2 Jun 2017 15:37:33 +0000 (11:37 -0400)]
pstore: Fix flags to enable dumps on powerpc
BugLink: http://bugs.launchpad.net/bugs/1691045
After commit c950fd6f201a kernel registers pstore write based on flag set.
Pstore write for powerpc is broken as flags(PSTORE_FLAGS_DMESG) is not set for
powerpc architecture. On panic, kernel doesn't write message to
/fs/pstore/dmesg*(Entry doesn't gets created at all).
This patch enables pstore write for powerpc architecture by setting
PSTORE_FLAGS_DMESG flag.
Fixes: c950fd6f201a ("pstore: Split pstore fragile flags") Cc: stable@vger.kernel.org # v4.9+ Signed-off-by: Ankit Kumar <ankit@linux.vnet.ibm.com> Signed-off-by: Kees Cook <keescook@chromium.org>
(cherry picked from commit 041939c1ec54208b42f5cd819209173d52a29d34) Signed-off-by: Joseph Salisbury <joseph.salisbury@canonical.com> Acked-by: Colin King <colin.king@canonical.com> Acked-by: Seth Forshee <seth.forshee@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Andy Lutomirski [Fri, 2 Jun 2017 04:55:02 +0000 (12:55 +0800)]
nvme: Quirk APST on Intel 600P/P3100 devices
BugLink: https://bugs.launchpad.net/bugs/1686592
They have known firmware bugs. A fix is apparently in the works --
once fixed firmware is available, someone from Intel (Hi, Keith!)
can adjust the quirk accordingly.
Cc: stable@vger.kernel.org # v4.11 Cc: Kai-Heng Feng <kai.heng.feng@canonical.com> Cc: Mario Limonciello <mario_limonciello@dell.com> Signed-off-by: Andy Lutomirski <luto@kernel.org> Signed-off-by: Christoph Hellwig <hch@lst.de>
(backported from commit 50af47d04ca530544b27affffb0722f158e2bb9c) Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Acked-by: Colin King <colin.king@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Signed-off-by: Quan Nguyen <qnguyen@apm.com> Signed-off-by: Iyappan Subramanian <isubramanian@apm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
(cherry picked from commit 4b72436dc3dd2457056b22d6f147777368c869fa) Signed-off-by: Joseph Salisbury <joseph.salisbury@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Stefan Bader [Wed, 17 May 2017 08:56:29 +0000 (10:56 +0200)]
UBUNTU: Ignore missing oxnas_nand
Upstream stable removed module from being built.
BugLink: https://bugs.launchpad.net/bugs/1691369 Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Stefan Bader [Wed, 17 May 2017 07:58:30 +0000 (09:58 +0200)]
UBUNTU: [Config] Remove CONFIG_MTD_NAND_OXNAS=m
This driver apparently is only needed for one specific platform.
So "mtd: nand: Add OX820 NAND hardware dependency" removes it from
being available if not compiling for ARCH_OXNAS.
Remove it from config.common.ubuntu (as far as I know none of our
master kernel and derivatives in main git tree supports that hw).
BugLink: https://bugs.launchpad.net/bugs/1691369 Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
BugLink: http://bugs.launchpad.net/bugs/1691369 Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Commit 25520d55cdb6 ("block: Inline blk_integrity in struct gendisk")
introduced blk_integrity_revalidate(), which seems to assume ownership
of the stable pages flag and unilaterally clears it if no blk_integrity
profile is registered:
if (bi->profile)
disk->queue->backing_dev_info->capabilities |=
BDI_CAP_STABLE_WRITES;
else
disk->queue->backing_dev_info->capabilities &=
~BDI_CAP_STABLE_WRITES;
It's called from revalidate_disk() and rescan_partitions(), making it
impossible to enable stable pages for drivers that support partitions
and don't use blk_integrity: while the call in revalidate_disk() can be
trivially worked around (see zram, which doesn't support partitions and
hence gets away with zram_revalidate_disk()), rescan_partitions() can
be triggered from userspace at any time. This breaks rbd, where the
ceph messenger is responsible for generating/verifying CRCs.
Since blk_integrity_{un,}register() "must" be used for (un)registering
the integrity profile with the block layer, move BDI_CAP_STABLE_WRITES
setting there. This way drivers that call blk_integrity_register() and
use integrity infrastructure won't interfere with drivers that don't
but still want stable pages.
Fixes: 25520d55cdb6 ("block: Inline blk_integrity in struct gendisk") Cc: "Martin K. Petersen" <martin.petersen@oracle.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Mike Snitzer <snitzer@redhat.com> Tested-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
[idryomov@gmail.com: backport to < 4.11: bdi is embedded in queue] Signed-off-by: Jens Axboe <axboe@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
The vm fault handler relies on the fact that the VMA owns a reference
to the BO. However, once mmap_sem is released, other tasks are free to
destroy the VMA, which can lead to the BO being freed. Fix two code
paths where that can happen, both related to vm fault retries.
Found via a lock debugging warning which flagged &bo->wu_mutex as
locked while being destroyed.
Fixes: cbe12e74ee4e ("drm/ttm: Allow vm fault retries") Signed-off-by: Nicolai Hähnle <nicolai.haehnle@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
We should be checking for IS_ERR() instead of NULL because
drm_dev_alloc() returns error pointers.
Fixes: 45d59d704080 ("drm: Add new driver for MXSFB controller") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Link: http://patchwork.freedesktop.org/patch/msgid/20161213122332.GA7519@elgon.mountain Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
1) INTx does not work because of the reset_watches path.
2) The reset_watches path is only taken if you have Xen > 4.0
3) The Linux Kernel by default will use vector inject if the hypervisor
support. So even INTx does not work no body running the kernel with
Xen > 4.0 would notice. Unless he explicitly disabled this feature
either in the kernel or in Xen (and this can only be disabled by
modifying the code, not user-supported way to do it).
After the offending commit (+ partial revert):
1) INTx is no longer support for HVM (only for PV guests).
2) Any HVM guest The kernel will not boot on Xen < 4.0 which does
not have vector injection support. Since the only other mode
supported is INTx which.
So based on this summary, I think before commit (72a9b186292) we were
in much better position from a user point of view.
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Reviewed-by: Juergen Gross <jgross@suse.com> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@redhat.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: x86@kernel.org Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: Bjorn Helgaas <bhelgaas@google.com> Cc: Stefano Stabellini <sstabellini@kernel.org> Cc: Julien Grall <julien.grall@arm.com> Cc: Vitaly Kuznetsov <vkuznets@redhat.com> Cc: Paul Gortmaker <paul.gortmaker@windriver.com> Cc: Ross Lagerwall <ross.lagerwall@citrix.com> Cc: xen-devel@lists.xenproject.org Cc: linux-kernel@vger.kernel.org Cc: linux-pci@vger.kernel.org Cc: Anthony Liguori <aliguori@amazon.com> Cc: KarimAllah Ahmed <karahmed@amazon.de> Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
F2FS uses 4 bytes to represent block address. As a result, supported
size of disk is 16 TB and it equals to 16 * 1024 * 1024 / 2 segments.
Signed-off-by: Jin Qian <jinqian@google.com> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Commit 91572088e3fd ("net: use core MTU range checking in core net
infra") changed the openvswitch internal device to use the core net
infra for controlling the MTU range, but failed to actually set the
max_mtu as described in the commit message, which now defaults to
ETH_DATA_LEN.
This patch fixes this by setting max_mtu to ETH_MAX_MTU after
ether_setup() call.
Fixes: 91572088e3fd ("net: use core MTU range checking in core net infra") Signed-off-by: Jarno Rajahalme <jarno@ovn.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
If an error is encountered in mdio_mux_init(), the error path will call
mdiobus_free(). Since mdiobus_register() has been called prior to
mdio_mux_init(), the bus->state will not be MDIOBUS_UNREGISTERED. This
causes a BUG_ON() in mdiobus_free(). To correct this issue, add an
error path for mdio_mux_init() which calls mdiobus_unregister() prior to
mdiobus_free().
Signed-off-by: Jon Mason <jon.mason@broadcom.com> Fixes: 98bc865a1ec8 ("net: mdio-mux: Add MDIO mux driver for iProc SoCs") Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
1) It checks the env->allow_ptr_leaks and only prints the map address to
the log if we have the privileges to do so, otherwise it just dumps 0
as we would when kptr_restrict is enabled on %pK. Given the latter is
off by default and not every distro sets it, I don't want to rely on
this, hence the 0 by default for unprivileged.
2) Printing of ldimm64 in the verifier log is currently broken in that
we don't print the full immediate, but only the 32 bit part of the
first insn part for ldimm64. Thus, fix this up as well; it's okay to
access, since we verified all ldimm64 earlier already (including just
constants) through replace_map_fd_with_map_ptr().
Fixes: 1be7f75d1668 ("bpf: enable non-root eBPF programs") Fixes: cbd357008604 ("bpf: verifier (add ability to receive verification log)") Reported-by: Jann Horn <jannh@google.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
We have the number of longs, but we need to calculate the number of
bytes required.
Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
For each netns (except init_net), we initialize its null entry
in 3 places:
1) The template itself, as we use kmemdup()
2) Code around dst_init_metrics() in ip6_route_net_init()
3) ip6_route_dev_notify(), which is supposed to initialize it after
loopback registers
Unfortunately the last one still happens in a wrong order because
we expect to initialize net->ipv6.ip6_null_entry->rt6i_idev to
net->loopback_dev's idev, thus we have to do that after we add
idev to loopback. However, this notifier has priority == 0 same as
ipv6_dev_notf, and ipv6_dev_notf is registered after
ip6_route_dev_notifier so it is called actually after
ip6_route_dev_notifier. This is similar to commit 2f460933f58e
("ipv6: initialize route null entry in addrconf_init()") which
fixes init_net.
Fix it by picking a smaller priority for ip6_route_dev_notifier.
Also, we have to release the refcnt accordingly when unregistering
loopback_dev because device exit functions are called before subsys
exit functions.
Acked-by: David Ahern <dsahern@gmail.com> Tested-by: David Ahern <dsahern@gmail.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Andrey reported a crash on init_net.ipv6.ip6_null_entry->rt6i_idev
since it is always NULL.
This is clearly wrong, we have code to initialize it to loopback_dev,
unfortunately the order is still not correct.
loopback_dev is registered very early during boot, we lose a chance
to re-initialize it in notifier. addrconf_init() is called after
ip6_route_init(), which means we have no chance to correct it.
Fix it by moving this initialization explicitly after
ipv6_add_dev(init_net.loopback_dev) in addrconf_init().
Reported-by: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Tested-by: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
IFLA_PHYS_PORT_NAME is a string attribute, so terminate it with \0.
Otherwise libnl3 fails to validate netlink messages with this attribute.
"ip -detail a" assumes too that the attribute is NUL-terminated when
printing it. It often was, due to padding.
I noticed this as libvirtd failing to start on a system with sfc driver
after upgrading it to Linux 4.11, i.e. when sfc added support for
phys_port_name.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
raw_send_hdrinc() and rawv6_send_hdrinc() expect that the buffer copied
from the userspace contains the IPv4/IPv6 header, so if too few bytes are
copied, parts of the header may remain uninitialized.
, triggered by the following syscalls:
socket(PF_INET6, SOCK_RAW, IPPROTO_RAW) = 3
sendto(3, NULL, 0, 0, {sa_family=AF_INET6, sin6_port=htons(0), inet_pton(AF_INET6, "ff00::", &sin6_addr), sin6_flowinfo=0, sin6_scope_id=0}, 28) = -1 EPERM
A similar report is triggered in net/ipv4/raw.c if we use a PF_INET socket
instead of a PF_INET6 one.
Signed-off-by: Alexander Potapenko <glider@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Under fuzzer stress, it is possible that a child gets a non NULL
fastopen_req pointer from its parent at accept() time, when/if parent
morphs from listener to active session.
We need to make sure this can not happen, by clearing the field after
socket cloning.
Fixes: e994b2f0fb92 ("tcp: do not lock listener to process SYN packets") Fixes: 7db92362d2fe ("tcp: fix potential double free issue for fastopen_req") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Andrey Konovalov <andreyknvl@google.com> Acked-by: Wei Wang <weiwan@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
This patch adds support for Telit ME910 PID 0x1100.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com> Acked-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Andrey's reproducer program runs in a very tight loop, calling
'unshare -n' and then spawning 2 sets of 14 threads running random ioctl
calls. The relevant networking sequence:
1. New network namespace created via unshare -n
- ip6tnl0 device is created in down state
2. address added to ip6tnl0
- equivalent to ip -6 addr add dev ip6tnl0 fd00::bb/1
- DAD is started on the address and when it completes the host
route is inserted into the FIB
3. ip6tnl0 is brought up
- the new fixup_permanent_addr function restarts DAD on the address
4. exit namespace
- teardown / cleanup sequence starts
- once in a blue moon, lo teardown appears to happen BEFORE teardown
of ip6tunl0
+ down on 'lo' removes the host route from the FIB since the dst->dev
for the route is loobback
+ host route added to rcu callback list
* rcu callback has not run yet, so rt is NOT on the gc list so it has
NOT been marked obsolete
5. in parallel to 4. worker_thread runs addrconf_dad_completed
- DAD on the address on ip6tnl0 completes
- calls ipv6_ifa_notify which inserts the host route
All of that happens very quickly. The result is that a host route that
has been deleted from the IPv6 FIB and added to the RCU list is re-inserted
into the FIB.
The exit namespace eventually gets to cleaning up ip6tnl0 which removes the
host route from the FIB again, calls the rcu function for cleanup -- and
triggers the double rcu trace.
The root cause is duplicate DAD on the address -- steps 2 and 3. Arguably,
DAD should not be started in step 2. The interface is in the down state,
so it can not really send out requests for the address which makes starting
DAD pointless.
Since the second DAD was introduced by a recent change, seems appropriate
to use it for the Fixes tag and have the fixup function only start DAD for
addresses in the PREDAD state which occurs in addrconf_ifdown if the
address is retained.
Big thanks to Andrey for isolating a reliable reproducer for this problem. Fixes: f1705ec197e7 ("net: ipv6: Make address flushing on ifdown optional") Reported-by: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: David Ahern <dsahern@gmail.com> Tested-by: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Be careful when comparing tcp_time_stamp to some u32 quantity,
otherwise result can be surprising.
Fixes: 7c106d7e782b ("[TCP]: TCP Low Priority congestion control") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
When the instruction right before the branch destination is
a 64 bit load immediate, we currently calculate the wrong
jump offset in the ctx->offset[] array as we only account
one instruction slot for the 64 bit load immediate although
it uses two BPF instructions. Fix it up by setting the offset
into the right slot after we incremented the index.
Also, add a couple of test cases to make sure JITs pass
this test. Tested on Cavium ThunderX ARMv8. The added
test cases all pass after the fix.
Fixes: 8eee539ddea0 ("arm64: bpf: fix out-of-bounds read in bpf2a64_offset()") Reported-by: David S. Miller <davem@davemloft.net> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Cc: Xi Wang <xi.wang@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
llvm 4.0 and above generates the code like below:
....
440: (b7) r1 = 15
441: (05) goto pc+73
515: (79) r6 = *(u64 *)(r10 -152)
516: (bf) r7 = r10
517: (07) r7 += -112
518: (bf) r2 = r7
519: (0f) r2 += r1
520: (71) r1 = *(u8 *)(r8 +0)
521: (73) *(u8 *)(r2 +45) = r1
....
and the verifier complains "R2 invalid mem access 'inv'" for insn #521.
This is because verifier marks register r2 as unknown value after #519
where r2 is a stack pointer and r1 holds a constant value.
Teach verifier to recognize "stack_ptr + imm" and
"stack_ptr + reg with const val" as valid stack_ptr with new offset.
Signed-off-by: Yonghong Song <yhs@fb.com> Acked-by: Martin KaFai Lau <kafai@fb.com> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Creating a geneve link with 'udpcsum' set results in a creation of link
for which UDP checksum will NOT be computed on outbound packets, as can
be seen below.
11: gen0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN
link/ether c2:85:27:b6:b4:15 brd ff:ff:ff:ff:ff:ff promiscuity 0
geneve id 200 remote 192.168.13.1 dstport 6081 noudpcsum
Similarly, creating a link with 'noudpcsum' set results in a creation
of link for which UDP checksum will be computed on outbound packets.
Fixes: 9b4437a5b870 ("geneve: Unify LWT and netdev handling.") Signed-off-by: Girish Moodalbail <girish.moodalbail@oracle.com> Acked-by: Pravin B Shelar <pshelar@ovn.org> Acked-by: Lance Richardson <lrichard@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Since 83a77e9ec415, the phydev irq is explicitly set to PHY_POLL when
there is no pdata. It doesn't work on DT enabled platforms because the
phydev irq is already set by libphy before.
Fixes: 83a77e9ec415 ("net: macb: Added PCI wrapper for Platform Driver.") Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Andrey found a way to trigger the WARN_ON_ONCE(delta < len) in
skb_try_coalesce() using syzkaller and a filter attached to a TCP
socket.
As we did recently in commit 158f323b9868 ("net: adjust skb->truesize in
pskb_expand_head()") we can adjust skb->truesize from ___pskb_trim(),
via a call to skb_condense().
If all frags were freed, then skb->truesize can be recomputed.
This call can be done if skb is not yet owned, or destructor is
sock_edemux().
Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Andrey Konovalov <andreyknvl@google.com> Cc: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Andrey found a way to trigger the WARN_ON_ONCE(delta < len) in
skb_try_coalesce() using syzkaller and a filter attached to a TCP
socket over loopback interface.
I believe one issue with looped skbs is that tcp_trim_head() can end up
producing skb with under estimated truesize.
It hardly matters for normal conditions, since packets sent over
loopback are never truncated.
Bytes trimmed from skb->head should not change skb truesize, since
skb->head is not reallocated.
Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Andrey Konovalov <andreyknvl@google.com> Tested-by: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
When any of the functions contained in NGbzero.S and GENbzero.S
vector through *bzero_from_clear_user, we may end up taking a
fault when executing one of the store alternate address space
instructions. If this happens, the exception handler does not
restore the %asi register.
This commit fixes the issue by introducing a new exception
handler that ensures the %asi register is restored when
a fault is handled.
Signed-off-by: Dave Aldridge <david.j.aldridge@oracle.com> Reviewed-by: Rob Gardner <rob.gardner@oracle.com> Reviewed-by: Babu Moger <babu.moger@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Imre Deak reported a deadlock of HD-audio driver at unbinding while
it's still in probing. Since we probe the codecs asynchronously in a
work, the codec driver probe may still be kicked off while the
controller itself is being unbound. And, azx_remove() tries to
process all pending tasks via cancel_work_sync() for fixing the other
races (see commit [0b8c82190c12: ALSA: hda - Cancel probe work instead
of flush at remove]), now we may meet a bizarre deadlock:
This deadlock is caused by the fact that both device_release_driver()
and driver_probe_device() take both the device and its parent locks at
the same time. The codec device sets the controller device as its
parent, and this lock is taken before the probe() callback is called,
while the controller remove() callback gets called also with the same
lock.
In this patch, as an ugly workaround, we unlock the controller device
temporarily during cancel_work_sync() call. The race against another
bind call should be still suppressed by the parent's device lock.
Reported-by: Imre Deak <imre.deak@intel.com> Fixes: 0b8c82190c12 ("ALSA: hda - Cancel probe work instead of flush at remove") Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
The newly added function triggers a harmless warning:
drivers/staging/lustre/lustre/ptlrpc/pack_generic.c: In function 'lustre_shrink_msg':
drivers/staging/lustre/lustre/ptlrpc/pack_generic.c:472:1: error: control reaches end of non-void function [-Werror=return-type]
This probably happens because LASSERTF() contains an 'unlikely()' that
sometimes prevents gcc from analysing the control flow correctly.
Adding a return statement here seems harmless and lets us keep that
unlikely().
Fixes: 96049bd1ecd0 ("staging: lustre: ptlrpc: embed highest XID in each request") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
The probe function is not marked __init, but some other functions
are. This leads to a warning on older compilers (e.g. gcc-4.3),
and can cause executing freed memory when built with those
compilers:
WARNING: drivers/staging/emxx_udc/emxx_udc.o(.text+0x2d78): Section mismatch in reference from the function nbu2ss_drv_probe() to the function .init.text:nbu2ss_drv_contest_init()
This removes the annotations.
Fixes: 33aa8d45a4fe ("staging: emxx_udc: Add Emma Mobile USB Gadget driver") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Conversion macros le16_to_cpu was removed and that caused new sparse warning
sparse output:
drivers/staging/wlan-ng/p80211netdev.c:241:44: warning: incorrect type in argument 2 (different base types)
drivers/staging/wlan-ng/p80211netdev.c:241:44: expected unsigned short [unsigned] [usertype] fc
drivers/staging/wlan-ng/p80211netdev.c:241:44: got restricted __le16 [usertype] fc
Fixes: 7ad82572348c ("staging:wlan-ng:Fix sparse warning") Signed-off-by: Igor Pylypiv <igor.pylypiv@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
root_squash control got accidentally moved to sysfs instead of
debugfs, and the write side of it was also broken expecting a
userspace buffer.
It contains both uid and gid values in a single file, so debugfs
is a clear place for it.
Reported-by: Al Viro <viro@ZenIV.linux.org.uk> Fixes: c948390f10ccc "fix inconsistencies of root squash feature" Signed-off-by: Oleg Drokin <green@linuxhacker.ru> Reviewed-by: James Simmons <jsimmons@infradead.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
The driver was making changes to the skb_header without
ensuring it was writable (i.e. uncloned).
This patch also removes some boiler plate header size
checking/adjustment code as that is also handled by the
skb_cow_header function used to make header writable.
Signed-off-by: James Hughes <james.hughes@raspberrypi.org> Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
The incoming skb header may be resized if header space is
insufficient, which might change the data adddress in the skb.
Ensure that a cached pointer to that data is correctly set by
moving assignment to after any possible changes.
Signed-off-by: James Hughes <james.hughes@raspberrypi.org> Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
This is easily avoided by using the generic 'struct tm' based helper rather
than the RTC specific one. While fixing this, I noticed that even though
the driver uses time64_t for storing seconds, it gets them from the
old 32-bit struct timeval. To address this, we can simplify the code
by calling ktime_get_real_seconds() directly.
Fixes: 6c223761eb54 ("smartpqi: initial commit of Microsemi smartpqi driver") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Don Brace <don.brace@microsemi.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
The mac_scsi driver still gets disabled when SCSI=m. This should have
been fixed back when I enabled the tristate but I didn't see the bug.
Fixes: 6e9ae6d560e1 ("[PATCH] mac_scsi: Add module option to Kconfig") Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Without CONFIG_DEBUG_FS, we run into a link error:
drivers/scsi/qedi/qedi_iscsi.o: In function `qedi_ep_poll':
qedi_iscsi.c:(.text.qedi_ep_poll+0x134): undefined reference to `do_not_recover'
drivers/scsi/qedi/qedi_iscsi.o: In function `qedi_ep_disconnect':
qedi_iscsi.c:(.text.qedi_ep_disconnect+0x36c): undefined reference to `do_not_recover'
drivers/scsi/qedi/qedi_iscsi.o: In function `qedi_ep_connect':
qedi_iscsi.c:(.text.qedi_ep_connect+0x350): undefined reference to `do_not_recover'
drivers/scsi/qedi/qedi_fw.o: In function `qedi_tmf_work':
qedi_fw.c:(.text.qedi_tmf_work+0x3b4): undefined reference to `do_not_recover'
This defines the symbol as a constant in this case, as there is no way to
set it to anything other than zero without DEBUG_FS. In addition, I'm renaming
it to qedi_do_not_recover in order to put it into a driver specific namespace,
as "do_not_recover" is a really bad name for a kernel-wide global identifier
when it is used only in one driver.
Fixes: ace7f46ba5fd ("scsi: qedi: Add QLogic FastLinQ offload iSCSI driver framework.") Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Manish Rangankar <Manish.Rangankar@cavium.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
'conn_info' is malloced in qedi_iscsi_update_conn() and should be freed
before leaving from the error handling cases, otherwise it will cause
memory leak.
Fixes: ace7f46ba5fd ("scsi: qedi: Add QLogic FastLinQ offload iSCSI driver framework.") Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Acked-by: Manish Rangankar <Manish.Rangankar@cavium.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Otherwise the interconnect related code implementing PM runtime will
produce these errors on a failed probe:
omap_uart 48066000.serial: omap_device: omap_device_enable() called from invalid state 1
omap_uart 48066000.serial: use pm_runtime_put_sync_suspend() in driver?
Note that we now also need to check for priv in omap8250_runtime_suspend()
as it has not yet been registered if probe fails. And we need to use
pm_runtime_put_sync() to properly idle the device like we already do
in omap8250_remove().
Fixes: 61929cf0169d ("tty: serial: Add 8250-core based omap driver") Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
We get the following compile errors if EXTCON is enabled as a
module but this driver is builtin:
drivers/built-in.o: In function `qcom_usb_hs_phy_power_off':
phy-qcom-usb-hs.c:(.text+0x1089): undefined reference to `extcon_unregister_notifier'
drivers/built-in.o: In function `qcom_usb_hs_phy_probe':
phy-qcom-usb-hs.c:(.text+0x11b5): undefined reference to `extcon_get_edev_by_phandle'
drivers/built-in.o: In function `qcom_usb_hs_phy_power_on':
phy-qcom-usb-hs.c:(.text+0x128e): undefined reference to `extcon_get_state'
phy-qcom-usb-hs.c:(.text+0x12a9): undefined reference to `extcon_register_notifier'
so let's mark this as needing to follow the modular status of
the extcon framework.
Fixes: 9994a33865f4 e2427b09ba929c2b9 (phy: Add support for Qualcomm's USB HS phy") Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
The mux_pll_src_apll_dpll_gpll_usb480m_p parent list was missing a ","
between the 3rd and 4th parent names, making them fall together and thus
lookups fail. Fix that.
Fixes: 5190c08b2989 ("clk: rockchip: add clock controller for rk3036") Signed-off-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
The modem-status register was read as part of device configuration at
port_probe and then again at open (and reset-resume). During open (and
reset-resume) the MSR was read before submitting the interrupt URB,
something which could lead to an MSR-change going unnoticed when it
races with open (reset-resume).
Fix this by dropping the redundant reconfiguration of the port at every
open, and only read the MSR after the interrupt URB has been submitted.
Fixes: 664d5df92e88 ("USB: usb-serial ch341: support for DTR/RTS/CTS") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Make sure to detect short control-message transfers so that errors are
logged when reading the modem status at open.
Note that while this also avoids initialising the modem status using
uninitialised heap data, these bits could not leak to user space as they
are currently not used.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Make sure to detect short control-message transfers when fetching
modem and line state in open and when retrieving registers.
This specifically makes sure that an errno is returned to user space on
errors in TIOCMGET instead of a zero bitmask.
Also drop the unused getdevice function which also lacked appropriate
error handling.
Fixes: f7a33e608d9a ("USB: serial: add quatech2 usb to serial driver") Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Fix open error handling which failed to detect errors when reading the
MSR and LSR registers, something which could lead to the shadow
registers being initialised from errnos.
Note that calling the generic close implementation is sufficient in the
error paths as the interrupt urb has not yet been submitted and the
register updates have not been made.
Fixes: f4c1e8d597d1 ("USB: ark3116: Make existing functions 16450-aware
and add close and release functions.") Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>