Marek Szyprowski [Tue, 12 Jun 2012 13:18:16 +0000 (10:18 -0300)]
[media] v4l: vb2-dma-contig: fail if user ptr buffer is not correctly aligned
The DMA transfer must be aligned to a specific value. If userptr is not aligned
to DMA requirements then unexpected corruptions of the memory may occur before
or after a buffer. To prevent such situations, all unligned userptr buffers
are rejected at VIDIOC_QBUF.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[media] v4l: vb2-dma-contig: add reference counting for a device from allocator context
This patch adds taking reference to the device for MMAP buffers.
Such buffers, may be exported using DMABUF mechanism. If the driver that
created a queue is unloaded then the queue is released, the device might be
released too. However, buffers cannot be released if they are referenced by
DMABUF descriptor(s). The device pointer kept in a buffer must be valid for the
whole buffer's lifetime. Therefore MMAP buffers should take a reference to the
device to avoid risk of dangling pointers.
Marek Szyprowski [Thu, 14 Jun 2012 14:32:21 +0000 (11:32 -0300)]
[media] v4l: vb2-dma-contig: let mmap method to use dma_mmap_coherent call
Let mmap method to use dma_mmap_coherent call. Moreover, this patch removes
vb2_mmap_pfn_range from videobuf2 helpers as it was suggested by Laurent
Pinchart. The function is no longer used in vb2 code.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Sumit Semwal [Thu, 14 Jun 2012 13:37:45 +0000 (10:37 -0300)]
[media] v4l: vb2-dma-contig: add support for dma_buf importing
This patch makes changes for adding dma-contig as a dma_buf user. It provides
function implementations for the {attach, detach, map, unmap}_dmabuf()
mem_ops of DMABUF memory type.
[author of the original patch]
[integration with refactored dma-contig allocator]
[media] v4l: vb2-dma-contig: add support for scatterlist in userptr mode
This patch introduces usage of dma_map_sg to map memory behind
a userspace pointer to a device as dma-contiguous mapping.
This patch contains some of the code kindly provided by Marek Szyprowski
<m.szyprowski@samsung.com> and Kamil Debski <k.debski@samsung.com> and Andrzej
Pietrasiewicz <andrzej.p@samsung.com>. Kind thanks for bug reports from Laurent
Pinchart <laurent.pinchart@ideasonboard.com> and Seung-Woo Kim
<sw0312.kim@samsung.com>.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[media] v4l: vb2-dma-contig: remove reference of alloc_ctx from a buffer
This patch removes a reference to alloc_ctx from an instance of a DMA
contiguous buffer. It helps to avoid a risk of a dangling pointer if the
context is released while the buffer is still valid. Moreover it removes one
dereference step while accessing a device structure.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Sumit Semwal [Thu, 14 Jun 2012 13:37:37 +0000 (10:37 -0300)]
[media] v4l: vb2: add support for shared buffer (dma_buf)
This patch adds support for DMABUF memory type in videobuf2. It calls relevant
APIs of dma_buf for v4l reqbuf / qbuf / dqbuf operations.
For this version, the support is for videobuf2 as a user of the shared buffer;
so the allocation of the buffer is done outside of V4L2. [A sample allocator of
dma-buf shared buffer is given at [1]]
[1]: Rob Clark's DRM:
https://github.com/robclark/kernel-omap4/commits/drmplane-dmabuf
[original work in the PoC for buffer sharing]
Sumit Semwal [Thu, 14 Jun 2012 13:37:35 +0000 (10:37 -0300)]
[media] v4l: Add DMABUF as a memory type
Adds DMABUF memory type to v4l framework. Also adds the related file
descriptor in v4l2_plane and v4l2_buffer.
[original work in the PoC for buffer sharing]
Since b9bf2eafaad9c1ef02fb3db38c74568be601a43a, the function
ds3000_firmware_ondemand() is called only once during init. This
locking scheme may have been useful when the firmware was loaded at
each tune.
Furthermore, it looks like this 'lock' was put in to prevent concurrent
access (and not recursion as the comments suggest). However, this open-
coded mechanism is anything but race-free and should have used a proper
mutex.
[media] cx25821: fix error return code and clean up
The function cx25821_sram_channel_setup_upstream_audio always return zero,
so the return value is not saved any more.
Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
While here, replace strlen()+kmemdup() to kstrdup().
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com> Reviewed-by: walter harms <wharms@bfs.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Fri, 16 Nov 2012 15:03:07 +0000 (12:03 -0300)]
[media] vpif_display: protect dma_queue by a spin_lock
The dma_queue list is accessed by both the interrupt handler and by normal
code. It needs to be protected by a lock to prevent possible list corruption.
Corruption has been observed in 'real-life' conditions. Adding this lock made
it go away.
Hans Verkuil [Fri, 16 Nov 2012 15:03:06 +0000 (12:03 -0300)]
[media] vpif_capture: protect dma_queue by a spin_lock
The dma_queue list is accessed by both the interrupt handler and by normal
code. It needs to be protected by a lock to prevent possible list corruption.
Wei Yongjun [Thu, 15 Nov 2012 12:18:17 +0000 (09:18 -0300)]
[media] davinci: vpif: fix return value check for vb2_dma_contig_init_ctx()
In case of error, the function vb2_dma_contig_init_ctx() returns
ERR_PTR() and never returns NULL. The NULL test in the return value
check should be replaced with IS_ERR().
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Wei Yongjun [Tue, 30 Oct 2012 12:49:38 +0000 (09:49 -0300)]
[media] davinci: vpif_display: fix return type check for v4l2_subdev_call()
The v4l2_subdev_call() call returns -ENODEV when subdev is
null and -ENOIOCTLCMD wnen no icotl is present.
This patch fixes the return type check for v4l2_subdev_call().
The pattern E == C1 && E == C2 is always false. This patch
fix this according to the assumption that && should be ||.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Wei Yongjun [Tue, 30 Oct 2012 12:45:00 +0000 (09:45 -0300)]
[media] davinci: vpif_capture: fix return type check for v4l2_subdev_call()
The v4l2_subdev_call() call returns -ENODEV when subdev is
null and -ENOIOCTLCMD wnen no icotl is present.
This patch fixes the return type check for v4l2_subdev_call().
The pattern E == C1 && E == C2 is always false. This patch
fix this according to the assumption that && should be ||.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Laurent Pinchart [Sat, 20 Oct 2012 20:47:22 +0000 (17:47 -0300)]
[media] v4l: Don't warn during link validation when encountering a V4L2 devnode
v4l2_subdev_link_validate_get_format() retrieves the remote pad format
depending on the entity type and prints a warning if the entity type is
not supported. The type check doesn't take the subtype into account, and
thus always prints a warning for device node types, even when supported.
Fix it.
[media] mt9v022: set y_skip_top field to zero as default
Set "y_skip_top" to zero and revise comment as I do not see this line
corruption on two different mt9v022 setups. The first read-out line
is perfectly fine. Add mt9v022 platform data configuring y_skip_top
for platforms that have issues with the first read-out line. Set
y_skip_top to 1 for pcm990 board.
[media] mt9v022: support required register settings in snapshot mode
Some camera systems cannot operate mt9v022 in normal mode and use
only the snapshot mode. The TechNote for mt9v022 (TN0960) and mt9v024
(TN-09-225) describes required register settings when configuring the
snapshot operation. The snapshot mode requires that certain automatic
functions of the image sensor should be disabled or set to fixed values.
According to the TechNote bit 2 and bit 9 in the register 0x20 must be
set in snapshot mode and unset for normal operation. This applies for
mt9v022 Rev.3 and mt9v024. Add required reg. 0x20 settings dependent on
sensor chip version.
Add controls for horizontal and vertical blanking. Also add an error
message for case that the control handler init failed. Since setting
the blanking registers is done by controls now, we shouldn't change
these registers outside of the control function. Use v4l2_ctrl_s_ctrl()
to set them.
Frank Schäfer [Sun, 23 Sep 2012 18:28:45 +0000 (15:28 -0300)]
[media] ov2640: add support for V4L2_MBUS_FMT_YUYV8_2X8, V4L2_MBUS_FMT_RGB565_2X8_BE
This is the result of experimenting with the SpeedLink VAD Laplace webcam.
The register sequence for V4L2_MBUS_FMT_YUYV8_2X8 has been identified by
analyzing USB-logs of this device running on MS Windows.
The mx1_camera driver has been broken for a few release cycles since
commit 6bd0812 (dmaengine: imx-dma: merge old dma-v1.c with imx-dma.c).
It seems there is no one even compile tested it since then, as doing
so will end up with the following error.
CC drivers/media/platform/soc_camera/mx1_camera.o
In file included from drivers/media/platform/soc_camera/mx1_camera.c:44:0:
arch/arm/mach-imx/include/mach/dma-mx1-mx2.h:8:25: fatal error: mach/dma-v1.h: No such file or directory
It seems there is no one being interested in bringing it back to
work [1] so far. Let's mark it BROKEN.
[1] https://lkml.org/lkml/2012/2/9/171
Shubhrajyoti D [Thu, 25 Oct 2012 04:02:36 +0000 (01:02 -0300)]
[media] adv7604: convert struct i2c_msg initialization to C99 format
Convert the struct i2c_msg initialization to C99 format. This makes
maintaining and editing the code simpler. Also helps once other fields
like transferred are added in future.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com> Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Sean Young [Wed, 24 Oct 2012 20:22:42 +0000 (17:22 -0300)]
[media] winbond-cir: add carrier detection
The winbond hardware has a counter for leading edges, which increases as
they are received. As we read raw IR from a fifo in an interrupt handler,
we cannot correlate them to specific IR pulses so we simply count all
pulses and edges until we go idle and disable the receiver.
Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Sean Young [Wed, 24 Oct 2012 20:22:40 +0000 (17:22 -0300)]
[media] winbond-cir: fix idle mode
The receiver is never disabled by idle mode since rxstate never gets set
to RXSTATE_ACTIVE, so we keep on getting interrupts after the first IR
activity ends. Note that ir_raw_event_reset() already calls
ir_raw_event_handle().
Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Ezequiel Garcia [Thu, 1 Nov 2012 11:42:00 +0000 (08:42 -0300)]
[media] stkwebcam: Fix sparse warning on undeclared symbol
The sparse warning is:
"drivers/media/usb/stkwebcam/stk-webcam.c:59:5:
warning: symbol 'first_init' was not declared. Should it be static?"
Declare variable 'first_init' as static and local to the function.
Found by Hans Verkuil's daily build. Tested by compilation only.
Murali Karicheri [Mon, 22 Oct 2012 14:41:36 +0000 (11:41 -0300)]
[media] media:davinci: clk - {prepare/unprepare} for common clk
As a first step towards migrating davinci platforms to use common clock
framework, replace all instances of clk_enable() with clk_prepare_enable()
and clk_disable() with clk_disable_unprepare().
Also fixes some issues related to clk clean up in the driver
Lad, Prabhakar [Fri, 9 Nov 2012 08:59:32 +0000 (05:59 -0300)]
[media] media: davinci: vpbe: fix build warning
Warnings were generated because of the following commit changed data type for
address pointer 195bbca ARM: 7500/1: io: avoid writeback addressing modes for __raw_ accessors
add __iomem annotation to fix following warnings
drivers/media/platform/davinci/vpbe_osd.c: In function ‘osd_read’:
drivers/media/platform/davinci/vpbe_osd.c:49:2: warning: passing
argument 1 of ‘__raw_readl’ makes pointer from integer without a cast [enabled by default]
arch/arm/include/asm/io.h:104:19: note: expected ‘const volatile
void *’ but argument is of type ‘long unsigned int’
This patch stores the ioremap_nocache() returned address in a
void __iomem * instead of a unsigned long and passes the same to
readl/writel functions which fixes the above warnings.
YAMANE Toshiaki [Mon, 5 Nov 2012 10:38:46 +0000 (07:38 -0300)]
[media] staging/media: Use dev_ printks in go7007/go7007-fw.c
fixed below checkpatch warning.
- WARNING: Prefer netdev_dbg(netdev, ... then dev_dbg(dev, ... then pr_debug(... to printk(KERN_DEBUG ...
- WARNING: Prefer netdev_err(netdev, ... then dev_err(dev, ... then pr_err(... to printk(KERN_ERR ...
YAMANE Toshiaki [Mon, 5 Nov 2012 10:38:12 +0000 (07:38 -0300)]
[media] staging/media: Use dev_ or pr_ printks in go7007/wis-saa7113.c
fixed below checkpatch warnings.
- WARNING: Prefer netdev_err(netdev, ... then dev_err(dev, ... then pr_err(... to printk(KERN_ERR ...
- WARNING: Prefer netdev_dbg(netdev, ... then dev_dbg(dev, ... then pr_debug(... to printk(KERN_DEBUG ...
YAMANE Toshiaki [Mon, 5 Nov 2012 10:36:26 +0000 (07:36 -0300)]
[media] staging/media: Use dev_ or pr_ printks in go7007/wis-saa7115.c
fixed below checkpatch warnings.
- WARNING: Prefer netdev_err(netdev, ... then dev_err(dev, ... then pr_err(... to printk(KERN_ERR ...
- WARNING: Prefer netdev_dbg(netdev, ... then dev_dbg(dev, ... then pr_debug(... to printk(KERN_DEBUG ...
YAMANE Toshiaki [Fri, 2 Nov 2012 11:09:29 +0000 (08:09 -0300)]
[media] Staging/media: Use dev_ printks in go7007/wis-ov7640.c
fixed below checkpatch warnings.
- WARNING: Prefer netdev_dbg(netdev, ... then dev_dbg(dev, ... then pr_debug(... to printk(KERN_DEBUG ...
- WARNING: Prefer netdev_err(netdev, ... then dev_err(dev, ... then pr_err(... to printk(KERN_ERR ...
Frank Schäfer [Sun, 23 Sep 2012 13:29:43 +0000 (10:29 -0300)]
[media] gspca_pac7302: use registers 0x01 and 0x03 for red and blue balance controls
Currently used registers 0xc5 and 0xc7 provide only a very coarse
adjustment possibility within a very small value range (0-3).
With registers 0x01 and 0x03, a fine grained adjustment with
255 steps is possible. This is also what the Windows driver does.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
R,G,B balance registers are 0x01-0x03 instead of 0x02-0x04,
which lead to the wrong conclusion that values are inverted.
Exposure is controlled via page 3 registers and this is already documented.
Also fix a whitespace issue.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Ezequiel Garcia [Wed, 24 Oct 2012 00:20:30 +0000 (21:20 -0300)]
[media] stk1160: Try to continue with fewer transfer buffers
Many people are trying to use stk1160 on low memory devices.
Instead of failing if one allocation fails, we allow the driver
to continue working if fewer transfer buffers are available.
As reported by Antti and by Stephen:
drivers/built-in.o: In function `sms_ir_event':
/home/david/checkouts/linux/drivers/media/common/siano/smsir.c:48: undefined reference to `ir_raw_event_store'
/home/david/checkouts/linux/drivers/media/common/siano/smsir.c:50: undefined reference to `ir_raw_event_handle'
drivers/built-in.o: In function `sms_ir_init':
/home/david/checkouts/linux/drivers/media/common/siano/smsir.c:56: undefined reference to `smscore_get_board_id'
/home/david/checkouts/linux/drivers/media/common/siano/smsir.c:60: undefined reference to `rc_allocate_device'
/home/david/checkouts/linux/drivers/media/common/siano/smsir.c:72: undefined reference to `sms_get_board'
/home/david/checkouts/linux/drivers/media/common/siano/smsir.c:92: undefined reference to `sms_get_board'
/home/david/checkouts/linux/drivers/media/common/siano/smsir.c:97: undefined reference to `rc_register_device'
/home/david/checkouts/linux/drivers/media/common/siano/smsir.c:100: undefined reference to `rc_free_device'
drivers/built-in.o: In function `sms_ir_exit':
/home/david/checkouts/linux/drivers/media/common/siano/smsir.c:111: undefined reference to `rc_unregister_device'
make: *** [vmlinux] Error 1
Caused by commit fdd1eeb49d36 "[media] siano: allow compiling it without RC support"
And it happens when CONFIG_SMS_SIANO_RC=y and CONFIG_RC_CORE=m .
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Reported-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Stefan Richter [Sat, 3 Nov 2012 08:25:20 +0000 (09:25 +0100)]
[media] firedtv: add MAINTAINERS entry
There is currently discussion to add MAINTAINERS records for media
drivers that don't have one yet, possibly with 'orphan' or 'odd fixes'
status. Here is a proper entry for the firedtv driver (for 1394
attached DVB STBs and 1394 attached DVB cards from Digital Everywhere).
The L: linux-media and T: linux-media.git lines in this entry are
redundant to what scripts/get_maintainer.pl would show automatically but
I added them for folks who read MAINTAINERS directly. The "(firedtv)"
string is for those folks as well if they look for driver name rather
than file path.
The F: drivers/media/firewire/ pattern and the "FireWire media drivers"
title are currently synonymous with firedtv. If more drivers get added
there, this can be revisited.
I don't have documentation or DVB-S2 devices to test, but I have DVB-C
and DVB-T devices for testing.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
While this file was always maintained, there was no explicit entry
for it.
There aren't many things happening at tm6000 side for a long time:
Driver works. This chip is already not sold anymore, so I don't
expect much changes on its side.
So, add a new entry with status equal to Odd fixes to better
reflect it.
While this file was always maintained, there was no explicit entry
for it.
There aren't many things happening at saa7134 side for a long time:
Driver works, and it is stable. When new patches are submitted,
they're new boards addition for hardware I don't have.
So, add a new entry with status equal to Odd fixes to better
reflect it.
While this file was always maintained, there was no explicit entry
for it.
There aren't many things happening at cx88 side for a long time:
Driver works, and it is stable. When new patches are submitted,
they're new boards addition for hardware I don't have.
So, add a new entry with status equal to Odd fixes to better
reflect it.
There aren't many things happening at bttv side for a long time:
Driver works, and it is stable. When new patches are submitted,
they're new boards addition for hardware I don't have. So,
move its status to Odd fixes to better reflect it.
David Härdeman [Wed, 31 Oct 2012 07:22:08 +0000 (04:22 -0300)]
[media] hid-picolcd_cir: fix compilation
Commit c003ab1bedf0 ("[media] rc-core: add separate defines for
protocol bitmaps and numbers") overlooked hid-picolcd.
This patch (against git.linuxtv.org/media_tree.git, branch
staging/for_v3.8) fixes the compilation breakage.
Signed-off-by: David Härdeman <david@hardeman.nu> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
projects / mirror_ubuntu-eoan-kernel.git / log