ath9k_hw: Fix instable target power control b/w CCK/OFDM
The problem is that when the attenuation is increased,
the rate will start to drop from MCS7 -> MCS6, and finally
will see MCS1 -> CCK_11Mbps. When the rate is changed b/w
CCK and OFDM, it will use register desired_scale to calculate
how much tx gain need to change.
The output power with the same tx gain for CCK and OFDM modulated
signals are different. This difference is constant for AR9280
but not AR9285/AR9271. It has different PA architecture
a constant. So it should be calibrated against this PA
characteristic.
The driver has to read the calibrated values from EEPROM and set
the tx power registers accordingly.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com> Acked-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211: Check for queued frames before entering power save.
In a highly noisy environment, the tx rate of the driver drops and
the application slows down since it has not yet received ACKs for
the frames already queued in the hardware. Since this ACK may take
more than 100ms, stopping the dev queues for entering PS at this
stage breaks applications, WMM test cases in my testing.
If there are frames already pending in the tx queue, postponing the
PS logic helps to avoid redundant queue stops. When power save is
enabled by default and in a noisy environment, this API certainly
helps in improving the average throughput.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Mon, 4 Apr 2011 13:16:29 +0000 (06:16 -0700)]
iwlagn: downgrade warning on unknown TLV
If we maintain API properly, then there isn't
really a reason to warn about this since we'll
just be adding things that are safe to ignore,
so downgrade the warning to debug info level.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Johannes Berg [Fri, 8 Apr 2011 15:14:56 +0000 (08:14 -0700)]
iwlagn: clean up & autodetect statistics
There's no need to keep both normal and BT statistics
versions around all the time in memory when we only
use a subset of both. So keep only the subsets that
we need in memory, depending on the debug config).
Also, in doing so, we can remove all the calls to
iwl_bt_statistics() in the driver as we'll just
access the copied statistics now.
Finally, also remove this call from the one place
where it might still be needed and automatically
detect what kind of statistics the device is sending
based on their size. This way, we don't need to keep
track of which devices do what any more, which is
good since this is subject to change based on the
ucode version (as some ucode even for non-BT devices
will in fact use BT statistics).
Warn upon encountering a statistics command from the
ucode that isn't known, so we will find such issues
earlier in the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Tested-by: Don Fry <donald.h.fry@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Garen Tamrazian [Wed, 30 Mar 2011 09:29:32 +0000 (02:29 -0700)]
iwlagn: fix radar frame rejection
The microcode may sometimes reject TX frames when
on a radar channel even after we associated as it
clears information during association and needs to
receive a new beacon before allowing that channel
again. This manifests itself as a TX status value
of TX_STATUS_FAIL_PASSIVE_NO_RX. So in this case,
stop the corresponding queue and give the frame
back to mac80211 for retransmission. We start the
queue again when a beacon from the AP is received
which will make the regulatory enforcement in the
device allow transmitting again.
Signed-off-by: Garen Tamrazian <garenx.tamrazian@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
We have no other option but to inform userspace that we
have queued up their regulatory hint request when we are
given one given that nl80211 operates atomically on user
requests. The best we can do is accept the request, and
add a delayed work item for processing failure and cancel it
if we succeeed. Upon failure we restore the regulatory
settings and ignore the user input.
This fixes this reported bug:
https://bugzilla.kernel.org/show_bug.cgi?id=28112
Reported-by: gregoryx.alagnou@intel.com Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we restore regulatory settings its possible CRDA
will not reply because of a bogus user entry. In this
case the bogus entry will prevent any further processing
on cfg80211 for regulatory domains even if we restore
regulatory settings.
To prevent this we suck out all pending requests when
restoring regulatory settings and add them back into the
queue after we have queued up the reset work.
The impact of not having this applied is that a user
with privileges can issue a userspace regulatory hint
while we are disasocciating and this would prevent any
further processing of regulatory domains.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Tue, 5 Apr 2011 16:42:12 +0000 (09:42 -0700)]
iwlagn: move IO functions out of line
This generates a massive reduction in module size:
with debug:
text data bss dec hex filename
670300 13136 420 683856 a6f50 iwlagn.ko (before)
388347 13136 408 401891 621e3 iwlagn.ko (after)
without debug:
text data bss dec hex filename
528575 13072 420 542067 84573 iwlagn.ko (before)
294192 13072 408 307672 4b1d8 iwlagn.ko (after)
This also removes all the IO debug functionality since
it can easily be replaced by tracing, and makes the
code unnecessarily complex.
I haven't done any CPU utilisation measurements, but
given that the hotpaths don't use much IO it is not
likely to have a negative impact; in fact, the size
reduction will reduce cache pressure which possibly
improves performance.
Finally, an unused function or two were removed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Tue, 5 Apr 2011 16:42:11 +0000 (09:42 -0700)]
iwlagn: remove ISR ops
The ISR (interrupt service routine) ops are now
no longer necessary since they are the same for
all devices this driver now handles.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Tue, 5 Apr 2011 16:42:10 +0000 (09:42 -0700)]
iwlagn: remove rxb page bookkeeping
We never use the value in alloc_rxb_page,
so there's no point in keeping it either.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Tue, 5 Apr 2011 16:42:09 +0000 (09:42 -0700)]
iwlagn: remove rev_id
The rev_id variable is only printed, we
don't need to store it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Tue, 5 Apr 2011 16:42:08 +0000 (09:42 -0700)]
iwlagn: remove hw_rev
The hw_rev variable is used only during init,
so there's no need to keep it around.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Tue, 5 Apr 2011 16:42:07 +0000 (09:42 -0700)]
iwlagn: remove hw_wa_rev
The variable is never used.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Tue, 5 Apr 2011 16:42:06 +0000 (09:42 -0700)]
iwlagn: remove BSM clock setting
Again, a 4965 specific code path that we no
longer need in iwlagn.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Tue, 5 Apr 2011 16:42:05 +0000 (09:42 -0700)]
iwlagn: init cmd_queue earlier
We know after loading the ucode whether it will
support PAN or not, so we can also initialise
the cmd_queue variable much earlier.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Tue, 5 Apr 2011 16:42:04 +0000 (09:42 -0700)]
iwlagn: clean up alive handling
Devices newer than 4965 don't actually send
two different versions of the ALIVE command,
so we always had a bug here since before this
patch we copy more data than we got. Remove
the iwl_init_alive_resp struct and don't use
it.
Since we also really don't need to track all
the data received in ALIVE as we only use the
error and log event tables later, we can also
save space by just keeping those and not more
data around in memory.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Tue, 5 Apr 2011 16:42:03 +0000 (09:42 -0700)]
iwlagn: fix ucode verify message
My previous patch left a message talking about
bootstrap, but that's clearly bogus.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Tue, 5 Apr 2011 16:42:02 +0000 (09:42 -0700)]
iwlagn: add feature flags
Some new devices and microcode files will a greater
variety of features, so the TLV-per-feature approach
we took before will quickly make things harder to
manage and increase the file size.
Add a new TLV that has feature flags. Currently, it
will contain:
1) a PAN feature flag, which moves from a separate
TLV
2) a new BT stats bit that indicates whether the
microcode image uses bluetooth statistics
3) a new MFP flag for management frame protection
which can be enabled once the device/microcode
supports it
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Tue, 5 Apr 2011 16:41:59 +0000 (09:41 -0700)]
iwlagn: remove ucode_data_backup
This was used only on 4965 in conjunction with
the bootstrap ucode.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Tue, 5 Apr 2011 16:41:58 +0000 (09:41 -0700)]
iwlagn: centralize and fix ucode restart
The ucode restart has to take into account a number
of things, like clearing the HCMD_ACTIVE and other
status bits, and waking up the wait_command_queue.
Currently, however, there are a number of places
that neither do that, nor actually set the FW error
bit that leads to proper restart handling, which
means that in those cases things will probably just
hang completely.
To clean this up, make all ucode restart go through
a single function, except for the cases where it's
called during firmware loading.
Also fix a bug in wimax coexist restart avoidance,
it needs to first clear the status bits (and it has
to clear the HCMD_ACTIVE one as well) and then wake
up anything waiting on wait_command_queue.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Tue, 5 Apr 2011 16:41:57 +0000 (09:41 -0700)]
iwlagn: remove bootstrap code
Only 4965 had a bootstrap microcode image, so
the agn driver can completely ignore that and
we can remove some code from it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Tue, 5 Apr 2011 16:41:56 +0000 (09:41 -0700)]
iwlagn: verify specific ucode
When we loaded a ucode, there's no point in
checking any one that is present, we know
which one is supposed to be present so also
verify that it is exactly the right one.
That also simplifies the code and makes it
faster since it doesn't have to check all.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Tue, 5 Apr 2011 16:41:55 +0000 (09:41 -0700)]
iwlagn: simplify ucode check code
The code in iwlcore_verify_inst_sparse really
doesn't need to keep track of the number of
errors it encountered since a single one is
fatal.
Also, the code in iwl_verify_inst_full is just
used to print out some things, so rename it to
iwl_print_inst and don't give it a return code
and just make it print out the values.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Tue, 5 Apr 2011 16:41:53 +0000 (09:41 -0700)]
iwlagn: remove pointless return variables
A number of places just use a variable to return
it right away, which is useless, so let's remove
the variables there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Tue, 5 Apr 2011 16:41:51 +0000 (09:41 -0700)]
iwlagn: clean up ucode loading
All agn devices behave the same, so there's no
need to go through function pointers for any
of the ucode loading functionality.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Tue, 5 Apr 2011 16:41:50 +0000 (09:41 -0700)]
iwlagn: make mac80211 handlers static
Now that these handlers are no longer shared
between 4965 and agn, they can be static.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Tue, 5 Apr 2011 16:41:49 +0000 (09:41 -0700)]
iwlagn: clean up some 3945/4965 remnants
When the driver was split, a bunch of definitions
for the 3945 and 4965 devices stayed around, but
they're now useless so remove (some of) them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Tue, 5 Apr 2011 16:41:48 +0000 (09:41 -0700)]
iwlagn: remove unused variable
Some code was removed, but a variable it used
and that is now unused stayed around, kill it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Michal Marek [Tue, 5 Apr 2011 14:59:06 +0000 (16:59 +0200)]
rt2x00: Drop __TIME__ usage
The kernel already prints its build timestamp during boot, no need to
repeat it in random drivers and produce different object files each
time.
Signed-off-by: Michal Marek <mmarek@suse.cz> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Cc: linux-wireless@vger.kernel.org Cc: netdev@vger.kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
Current ath9k code does not handle beacon timers on opmode
specific. One such example is that a STA beacon config overwrites
already configured AP vif's beacon timers during scan.
On multi station vif case, configure beacon timers beased
on primary vif selected. This also helps while moving back
to single STA vif from multi STA vifs, where the power save
is enabled and hw has to be reconfigured with proper
beacon and bssid/aid. Otherwise connection poll will be triggered
so frequently due to beacon loss.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
As of now bssid/aid is overridden with recently changed vif's
bss config. This may cause improper beacon updation due to
bssid/aid mismatch. On station mode, select an associated
sta vif as primary vif and configure that vif's bss into hw.
Update the primary vif on interface change and bss info change.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
The present check denies the IBSS interface addtion if we
already have any other vifs. But it fails to deny interface
addition if IBSS was already present.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jarkko Nikula [Mon, 4 Apr 2011 08:04:58 +0000 (11:04 +0300)]
wl1251: Add support for idle mode
On Nokia N900 the wl1251 consumes the most power when the interface is up
but not associated to access point (that supports PSM). In terms of battery
current consumption, the consumption is ~180 mA higher when the interface is
up but not associated and only ~5 mA higher when associated compared to
interface down and driver not loaded cases.
This patch adds support for the mac80211 idle notifications. Chip is put into
idle very much the same way when entering into PSM by utilizing the Extreme
Low Power (ELP) mode. I.e. idle is entered by setting necessary conditions
in wl1251_ps_set_mode followed by a call to wl1251_ps_elp_sleep.
It seems it is just enough the authorize ELP mode followed by
CMD_DISCONNECT (thanks to Kalle Valo about the idea to use it).
Without disconnect command the chip remains somewhat active and stays
consuming ~20 mA. Idle mode is left by same way than PSM. The wl1251_join
call is used to revert the CMD_DISCONNECT. Without it association to AP
doesn't work when trying second time.
With this patch the interface up but not associated case the battery current
consumption is less than 1 mA higher compared to interface down case.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com> Acked-by: Kalle Valo <kvalo@adurom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jarkko Nikula [Mon, 4 Apr 2011 08:04:57 +0000 (11:04 +0300)]
wl1251: Prepare for idle mode support
RFC for WL1251 idle mode support brought a few issues that are worth to
update before adding the idle mode support.
Since the idle mode can reuse the code that is now used in Power Save Mode
(PSM), the flag psm in struct wl1251 is changed to variable station_mode
to be able to distinguish between PSM and idle modes.
As the station mode is different than the power power save mode command
that is sent to chip, the enum wl1251_cmd_ps_mod values are used only when
communicating with the chip and new enum wl1251_station_mode values are used
inside the driver.
Confusing comment about psm and elp relation is removed since the PSM is
actually activated by putting the chip into Entreme Low Power (ELP) mode.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com> Acked-by: Kalle Valo <kvalo@adurom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jussi Kivilinna [Sat, 2 Apr 2011 08:25:54 +0000 (11:25 +0300)]
zd1211rw: rename CR* macros to ZD_CR*
With compat-wireless CR* macros in zd_usb.h conflict with CR macros in
include/asm-generic/termbits.h. So rename CR* macros to ZD_CR*.
Conversion was done with using sed and then 'over 80 character line'
checkpatch.pl warnings and comment indents were fixed.
Reported-by: Walter Goldens <goldenstranger@yahoo.com> Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sat, 2 Apr 2011 01:39:48 +0000 (03:39 +0200)]
ath9k: use the hw opmode to select the beacon timer mode
Since the beacon timers are global, the individual vif type should not
be used to determine the beacon timer configuration mode, use the
global opmode instead.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sat, 2 Apr 2011 01:39:47 +0000 (03:39 +0200)]
ath9k: fix beacon slot processing in ad-hoc mode
The recent cleanups in the beacon code fixed SWBA backoff calculation,
however it did not remove a line of code that worked around the issues
from the earlier version of the code.
After the cleanup, the initial TSF based slot calculation now always
returns 0 instead of ATH_BCBUF-1, so the previous hack that reversed the
slot order needs to be removed, as ad-hoc mode does not use staggered
beacons.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mwifiex: return success in set_default_key for WPA/WPA2
When testing wpa_supplicant with 'nl80211' driver to connect
to an AP with WPA/WPA2 security, we notice the followings:
1) add_key is called firstly with the key from cfg80211
2) set_defaut_key is called next
set_default_key() is specific to WEP keys and should not be
called in case of WPA/WPA2 security. The set_default_key()
won't be called if wpa_supplicant uses "-Dwext" option,
but it's been called if "-Dnl80211" option is specified.
We can fix this issue by adding a check to return from
set_default_key() if WEP key is not configured.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: Marc Yang <yangyang@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Paul Stewart [Thu, 31 Mar 2011 16:25:41 +0000 (09:25 -0700)]
nl80211: Add BSS parameters to station
This allows user-space monitoring of BSS parameters for the associated
station. This is useful for debugging and verifying that the paramaters
are as expected.
[Exactly the same as before but bundled into a single message]
Signed-off-by: Paul Stewart <pstew@chromium.org> Cc: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
We now use priv->mutex to serialize sync command, remove old
priv->sync_cmd_mutex and add assertion that priv->mutex must be locked.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check status bits with mutex taken, because when we wait for mutex
unlock, status can change. Patch should also make remaining sync
commands be send with priv->mutex taken. That will prevent execute
these commands when we are currently reset firmware, what could
possibly cause troubles.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
We mark command as huge by using meta->flags from other (non huge) command,
but flags can be possibly overridden, when non huge command is enqueued,
what can lead to:
WARNING: at lib/dma-debug.c:696 dma_debug_device_change+0x1a3/0x1f0()
DMA-API: device driver has pending DMA allocations while released from device [count=1]
To fix introduce additional CMD_MAPPED to mark command as mapped and
serialize iwl_enqueue_hcmd() with iwl_tx_cmd_complete() using
hcmd_lock. Serialization will also fix possible race conditions,
because q->read_ptr, q->write_ptr are modified/used in parallel.
On the way fix whitespace.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joe Culler reported a problem with his AR9170 device:
> ath: EEPROM regdomain: 0x5c
> ath: EEPROM indicates we should expect a direct regpair map
> ath: invalid regulatory domain/country code 0x5c
> ath: Invalid EEPROM contents
It turned out that the regdomain 'APL7_FCCA' was not mapped yet.
According to Luis R. Rodriguez [Atheros' engineer] APL7 maps to
FCC_CTL and FCCA maps to FCC_CTL as well, so the attached patch
should be correct.
Cc: <stable@kernel.org> Reported-by: Joe Culler <joe.culler@gmail.com> Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Brian Cavagnolo [Wed, 6 Apr 2011 08:48:46 +0000 (14:18 +0530)]
mwl8k: do not free unrequested irq
When the mwl8k driver attempts and fails to switch from sta to ap
firmware (or vice-versa) in the mwl8k_add_interface routine, the
mwl8k_stop routine will be called. This routine must not attempt
to free the irq if it was not requested.
Signed-off-by: Brian Cavagnolo <brian@cozybit.com> Signed-off-by: Nishant Sarmukadam <nishants@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Tue, 5 Apr 2011 15:55:05 +0000 (08:55 -0700)]
iwlagn: override 5300 EEPROM # of chains
At least EEPROM version 0x11A has the wrong
number of chains programmed into it for some
reason, so we need to override in the driver.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johan Hedberg [Wed, 30 Mar 2011 20:57:16 +0000 (23:57 +0300)]
Bluetooth: Add mgmt_device_found event
This patch adds a device_found event to the Management interface. For
now the event only maps to BR/EDR inquiry result HCI events, but in the
future the plan is to also use it for the LE device discovery process.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Johannes Berg [Fri, 1 Apr 2011 11:52:48 +0000 (13:52 +0200)]
mac80211: clean up station cleanup timer
We currently run this timer exactly once when
a new mac80211 device is registered, but that
is completely pointless since it will have no
work to do at all. Therefore, remove that and
also simplify some code using the timer.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Mon, 28 Mar 2011 11:35:51 +0000 (13:35 +0200)]
rt2x00: Add an error message when trying to send on a full queue
We already tell mac80211 to stop the queue when we hit a certain
threshold. Hence, it shouldn't happen at all that a frame gets queued
for tx on a full queue. Add an error message for this case.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Mon, 28 Mar 2011 11:35:21 +0000 (13:35 +0200)]
rt2x00: Fix tx aggregation problems with some clients
Some clients seem to rely upon the reception of BlockAckReqs to flush
their rx reorder buffer. In order to fix aggregation for these clients
rt2x00 should send a BlockAckReq if the transmission of an AMPDU
subframe fails.
Introduce a new flag TXDONE_AMPDU to indicate that this is an AMPDU
subframe and pass IEEE80211_TX_STAT_AMPDU_NO_BACK to mac80211 if an
AMPDU subframe failed during transmission.
This fixes aggregation problems with Intel 5100 Windows STAs (and maybe
others as well).
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Mon, 28 Mar 2011 11:34:15 +0000 (13:34 +0200)]
rt2x00: Fix STBC transmissions to STAs with Rx STBC > 1
For STBC transmissions rt2x00 used the number of RxSTBC streams the
destination STA indicates in its HT capabilities as STBC value in
the TXWI.
However, the legacy drivers and our own comment in rt2800.h suggest
that the STBC field in the TXWI only allows a value of 0 or 1.
The values 2 and 3 are reserved (probably for future devices).
And indeed, STBC transmissions to STAs indicating more then 1
RxSTBC stream fail when the STBC field is set to something >1.
Fix this by only setting the STBC field to 1 when STBC should be
used.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Mon, 28 Mar 2011 11:33:40 +0000 (13:33 +0200)]
rt2x00: Implement tx power temperature compensation
rt2800 devices should adjust their tx power in accordance with the
eeproms temperature calibration values. Add a new driver callback
gain_calibration that is called every 4 seconds.
The rt2800 gain calibration routine simply runs the tx power
configuration that takes care of calculating the temperature
compensation delta.
We don't need to synchronize the calls to rt2800_config_txpower
as they should all happen from mac80211's single threaded workqueue.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
projects / mirror_ubuntu-disco-kernel.git / log