BugLink: http://bugs.launchpad.net/bugs/1611833 Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
file_remove_privs() is called with inode lock on file_inode(), which
proceeds to calling notify_change() on file->f_path.dentry. Which triggers
the WARN_ON_ONCE(!inode_is_locked(inode)) in addition to deadlocking later
when ovl_setattr tries to lock the underlying inode again.
Fix this mess by not mixing the layers, but doing everything on underlying
dentry/inode.
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com> Fixes: 07a2daab49c5 ("ovl: Copy up underlying inode's ->i_mode to overlay inode") Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Commit aebea2ba0f74 ("net: mvneta: fix Tx interrupt delay") intended to
set coalescing threshold to a value guaranteeing interrupt generation
per each sent packet, so that buffers can be released with no delay.
In fact setting threshold to '1' was wrong, because it causes interrupt
every two packets. According to the documentation a reason behind it is
following - interrupt occurs once sent buffers counter reaches a value,
which is higher than one specified in MVNETA_TXQ_SIZE_REG(q). This
behavior was confirmed during tests. Also when testing the SoC working
as a NAS device, better performance was observed with int-per-packet,
as it strongly depends on the fact that all transmitted packets are
released immediately.
This commit enables NETA controller work in interrupt per sent packet mode
by setting coalescing threshold to 0.
Signed-off-by: Dmitri Epshtein <dima@marvell.com> Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Fixes aebea2ba0f74 ("net: mvneta: fix Tx interrupt delay") Acked-by: Willy Tarreau <w@1wt.eu> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Currently, osd_weight and osd_state fields are updated in the encoding
order. This is wrong, because an incremental map may look like e.g.
new_up_client: { osd=6, addr=... } # set osd_state and addr
new_state: { osd=6, xorstate=EXISTS } # clear osd_state
Suppose osd6's current osd_state is EXISTS (i.e. osd6 is down). After
applying new_up_client, osd_state is changed to EXISTS | UP. Carrying
on with the new_state update, we flip EXISTS and leave osd6 in a weird
"!EXISTS but UP" state. A non-existent OSD is considered down by the
mapping code
2087 for (i = 0; i < pg->pg_temp.len; i++) {
2088 if (ceph_osd_is_down(osdmap, pg->pg_temp.osds[i])) {
2089 if (ceph_can_shift_osds(pi))
2090 continue;
2091
2092 temp->osds[temp->size++] = CRUSH_ITEM_NONE;
and so requests get directed to the second OSD in the set instead of
the first, resulting in OSD-side errors like:
[WRN] : client.4239 192.168.122.21:0/2444980242 misdirected client.4239.1:2827 pg 2.5df899f2 to osd.4 not [1,4,6] in e680/680
and hung rbds on the client:
[ 493.566367] rbd: rbd0: write 400000 at 11cc00000 (0)
[ 493.566805] rbd: rbd0: result -6 xferred 400000
[ 493.567011] blk_update_request: I/O error, dev rbd0, sector 9330688
The fix is to decouple application from the decoding and:
- apply new_weight first
- apply new_state before new_up_client
- twiddle osd_state flags if marking in
- clear out some of the state if osd is destroyed
Since 34b48db66e08 ("block: remove artifical max_hw_sectors cap"),
max_sectors is no longer limited to BLK_DEF_MAX_SECTORS and LITE-ON
CX1-JB256-HP keeps timing out with higher max_sectors. Revert it to
the previous value.
Variable "now" seems to be genuinely used unintialized
if branch
if (CPUCLOCK_PERTHREAD(timer->it_clock)) {
is not taken and branch
if (unlikely(sighand == NULL)) {
is taken. In this case the process has been reaped and the timer is marked as
disarmed anyway. So none of the postprocessing of the sample is
required. Return right away.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Link: http://lkml.kernel.org/r/20160707223911.GA26483@p183.telecom.by Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
If we fall back to using LSI on the Croc or Crocodile chip we need to
clear the interrupt so we don't hang the system.
Tested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Commit b704f70ce200 ("SCSI: fix bug in scsi_dev_info_list matching")
changed the way vendor- and model-string matching was carried out in the
routine that looks up entries in a SCSI devinfo list. The new matching
code failed to take into account the case of a maximum-length string; in
such cases it could end up testing for a terminating '\0' byte beyond
the end of the memory allocated to the string. This out-of-bounds bug
was detected by UBSAN.
I don't know if anybody has actually encountered this bug. The symptom
would be that a device entry in the blacklist might not be matched
properly if it contained an 8-character vendor name or a 16-character
model name. Such entries certainly exist in scsi_static_device_list.
This patch fixes the problem by adding a check for a maximum-length
string before the '\0' test.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Fixes: b704f70ce200 ("SCSI: fix bug in scsi_dev_info_list matching") Tested-by: Wilfried Klaebe <linux-kernel@lebenslange-mailadresse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
If register_pernet_subsys() fails, we shouldn't try to call
unregister_pernet_subsys().
Fixes: 467fa15356 ("RDS-TCP: Support multiple RDS-TCP listen endpoints, one per netns.") Cc: Sowmini Varadhan <sowmini.varadhan@oracle.com> Cc: David S. Miller <davem@davemloft.net> Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com> Acked-by: Sowmini Varadhan <sowmini.varadhan@oracle.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
For 'real' hardware CAN devices the netlink interface is used to set CAN
specific communication parameters. Real CAN hardware can not be created nor
removed with the ip tool ...
This patch adds a private dellink function for the CAN device driver interface
that does just nothing.
It's a follow up to commit 993e6f2fd ("can: fix oops caused by wrong rtnl
newlink usage") but for dellink.
Reported-by: ajneu <ajneu1@gmail.com> Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
With upstream commit bb208f144cf3f59 (can: fix handling of unmodifiable
configuration options) a new can_validate() function was introduced.
When invoking 'ip link set can0 type can' without any configuration data
can_validate() tries to validate the content without taking into account that
there's totally no content. This patch adds a check for missing content.
Reported-by: ajneu <ajneu1@gmail.com> Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
When testing CAN write floods on Altera's CycloneV, the first 2 bytes
are sometimes 0x00, 0x00 or corrupted instead of the values sent. Also
observed bytes 4 & 5 were corrupted in some cases.
The D_CAN Data registers are 32 bits and changing from 16 bit writes to
32 bit writes fixes the problem.
Testing performed on Altera CycloneV (D_CAN). Requesting tests on other
C_CAN & D_CAN platforms.
Reported-by: Richard Andrysek <richard.andrysek@gomtec.de> Signed-off-by: Thor Thayer <tthayer@opensource.altera.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
At high bus load it could happen that "at91_poll()" enters with all RX
message boxes filled up. If then at the end the "quota" is exceeded as
well, "rx_next" will not be reset to the first RX mailbox and hence the
interrupts remain disabled.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Tested-by: Amr Bekhit <amrbekhit@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Before 4bacc9c9234c ("overlayfs: Make f_path...") file->f_path pointed to
the underlying file, hence suid/sgid removal on write worked fine.
After that patch file->f_path pointed to the overlay file, and the file
mode bits weren't copied to overlay_inode->i_mode. So the suid/sgid
removal simply stopped working.
The fix is to copy the mode bits, but then ovl_setattr() needs to clear
ATTR_MODE to avoid the BUG() in notify_change(). So do this first, then in
the next patch copy the mode.
Reported-by: Eryu Guan <eguan@redhat.com> Signed-off-by: Miklos Szeredi <mszeredi@redhat.com> Fixes: 4bacc9c9234c ("overlayfs: Make f_path always point to the overlay and f_inode to the underlay") Cc: Eric Schultz <eric@startuperic.com> Cc: Eric Hameleers <alien@slackware.com>
[backported by Eric Hameleers as seen in https://bugzilla.kernel.org/show_bug.cgi?id=150711] Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
fde7d22e01aa ("sched/fair: Fix overly small weight for interactive group entities")
calc_tg_weight() doesn't compute the right value as expected by effective_load().
The difference is in the 'correction' term. In order to ensure \Sum
rw_j >= rw_i we cannot use tg->load_avg directly, since that might be
lagging a correction on the current cfs_rq->avg.load_avg value.
Therefore we use tg->load_avg - cfs_rq->tg_load_avg_contrib +
cfs_rq->avg.load_avg.
Now, per the referenced commit, calc_tg_weight() doesn't use
cfs_rq->avg.load_avg, as is later used in @w, but uses
cfs_rq->load.weight instead.
So stop using calc_tg_weight() and do it explicitly.
The effects of this bug are wake_affine() making randomly
poor choices in cgroup-intense workloads.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Fixes: fde7d22e01aa ("sched/fair: Fix overly small weight for interactive group entities") Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
The code that fills packed command header assumes that CPU runs in
little-endian mode. Hence the header is malformed in big-endian mode
and causes MMC data transfer errors:
[ 563.200828] mmcblk0: error -110 transferring data, sector 2048, nr 8, cmd response 0x900, card status 0xc40
[ 563.219647] mmcblk0: packed cmd failed, nr 2, sectors 16, failure index: -1
Convert header data to LE.
Signed-off-by: Taras Kondratiuk <takondra@cisco.com> Fixes: ce39f9d17c14 ("mmc: support packed write command for eMMC4.5 devices") Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
get_task_ioprio() accesses the task->io_context without holding the task
lock and thus can race with exit_io_context(), leading to a
use-after-free. The reproducer below hits this within a few seconds on
my 4-core QEMU VM:
We verify "u_cmd.outsize" and "u_cmd.insize" but we need to make sure
that those values have not changed between the two copy_from_user()
calls. Otherwise it could lead to a buffer overflow.
Additionally, cros_ec_cmd_xfer() can set s_cmd->insize to a lower value.
We should use the new smaller value so we don't copy too much data to
the user.
Reported-by: Pengfei Wang <wpengfeinudt@gmail.com> Fixes: a841178445bb ('mfd: cros_ec: Use a zero-length array for command data') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Kees Cook <keescook@chromium.org> Tested-by: Gwendal Grignou <gwendal@chromium.org> Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
The flags element of clk_init_data was never initialized for mmc-
phase-clocks resulting in the element containing a random value
and thus possibly enabling unwanted clock flags.
Fixes: 89bf26cbc1a0 ("clk: rockchip: Add support for the mmc clock phases using the framework") Signed-off-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
When testing SPI without DMA I noticed that filling the FIFO on the
spi controller causes timeout.
Always leave room for one byte in the FIFO.
Signed-off-by: Michal Suchanek <hramrach@gmail.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
The trasfer timeout is fixed at 1000 ms. Reading a 4Mbyte flash over
1MHz SPI bus takes way longer than that. Calculate the timeout from the
actual time the transfer is supposed to take and multiply by 2 for good
measure.
Signed-off-by: Michal Suchanek <hramrach@gmail.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
- m_start() in fs/namespace.c expects that ns->event is incremented each
time a mount added or removed from ns->list.
- umount_tree() removes items from the list but does not increment event
counter, expecting that it's done before the function is called.
- There are some codepaths that call umount_tree() without updating
"event" counter. e.g. from __detach_mounts().
- When this happens m_start may reuse a cached mount structure that no
longer belongs to ns->list (i.e. use after free which usually leads
to infinite loop).
This change fixes the above problem by incrementing global event counter
before invoking umount_tree().
Change-Id: I622c8e84dcb9fb63542372c5dbf0178ee86bb589 Signed-off-by: Andrey Ulanov <andreyu@google.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
v9fs may be used as lower layer of overlayfs and accessing f_path.dentry
can lead to a crash. In this case it's a NULL pointer dereference in
p9_fid_create().
Fix by replacing direct access of file->f_path.dentry with the
file_dentry() accessor, which will always return a native object.
Reported-by: Alessio Igor Bogani <alessioigorbogani@gmail.com> Signed-off-by: Miklos Szeredi <mszeredi@redhat.com> Tested-by: Alessio Igor Bogani <alessioigorbogani@gmail.com> Fixes: 4bacc9c9234c ("overlayfs: Make f_path always point to the overlay and f_inode to the underlay") Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Although the extent tree depth of 5 should enough be for the worst
case of 2*32 extents of length 1, the extent tree code does not
currently to merge nodes which are less than half-full with a sibling
node, or to shrink the tree depth if possible. So it's possible, at
least in theory, for the tree depth to be greater than 5. However,
even in the worst case, a tree depth of 32 is highly unlikely, and if
the file system is maliciously corrupted, an insanely large eh_depth
can cause memory allocation failures that will trigger kernel warnings
(here, eh_depth = 65280):
There are legitimate reasons to disallow mmap on certain files, notably
in sysfs or procfs. We shouldn't emulate mmap support on file systems
that don't offer support natively.
CVE-2016-1583
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
[tyhicks: clean up f_op check by using ecryptfs_file_to_lower()] Signed-off-by: Tyler Hicks <tyhicks@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
It fixed a local root exploit but also introduced a dependency on
the lower file system implementing an mmap operation just to open a file,
which is a bit of a heavy hammer. The right fix is to have mmap depend
on the existence of the mmap handler instead.
Signed-off-by: Jeff Mahoney <jeffm@suse.com> Signed-off-by: Tyler Hicks <tyhicks@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
ltp fcntl33 testcase caused an Oops in selinux_file_send_sigiotask.
The reason is that generic_add_lease() used filp->f_path.dentry->inode
while all the others use file_inode(). This makes a difference for files
opened on overlayfs since the former will point to the overlay inode the
latter to the underlying inode.
So generic_add_lease() added the lease to the overlay inode and
generic_delete_lease() removed it from the underlying inode. When the file
was released the lease remained on the overlay inode's lock list, resulting
in use after free.
Reported-by: Eryu Guan <eguan@redhat.com> Fixes: 4bacc9c9234c ("overlayfs: Make f_path always point to the overlay and f_inode to the underlay") Signed-off-by: Miklos Szeredi <mszeredi@redhat.com> Reviewed-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Change power_supply_read_temp() to use power_supply_get_property()
so that it will check the use_cnt and ensure it is > 0. The use_cnt
will be incremented at the end of __power_supply_register, so this
will block to case where get_property can be called before the supply
is fully registered. This fixes the issue show in the stack below:
Also make the same change to ps_get_max_charge_cntl_limit() and
ps_get_cur_chrage_cntl_limit() to be safe. Lastly, change the return
value of power_supply_get_property() to -EAGAIN from -ENODEV if
use_cnt <= 0.
Fixes: 297d716f6260 ("power_supply: Change ownership from driver to core") Signed-off-by: Rhyland Klein <rklein@nvidia.com> Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Sebastian Reichel <sre@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
If percpu_ref initialization fails during css_create(), the free path
can end up trying to free css->id of zero. As ID 0 is unused, it
doesn't cause a critical breakage but it does trigger a warning
message. Fix it by setting css->id to -1 from init_and_link_css().
Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Wenwei Tao <ww.tao0320@gmail.com> Fixes: 01e586598b22 ("cgroup: release css->id after css_free") Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Some PINs do not have a MUX register, it is not an error.
It is necessary to allow the continuation of the PINs configuration,
otherwise the whole PIN-group will be configured incorrectly.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
With many repeated suspend resume cycles, the pin specific wakeirq
may not always work on omaps. This is because the write to enable the
pin interrupt may not have reached the device over the interconnect
before suspend happens.
Let's fix the issue with a flush of posted write with a readback.
Reported-by: Nishanth Menon <nm@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Protocol for the "version" fields is: hypervisor raises it (making it
uneven) before it starts updating the fields and raises it again (making
it even) when it is done. Thus the guest can make sure the time values
it got are consistent by checking the version before and after reading
them.
Add CPU barries after getting version value just like what function
vread_pvclock does, because all of callees in this function is inline.
Fixes: 502dfeff239e8313bfbe906ca0a1a6827ac8481b Signed-off-by: Minfei Huang <mnghuan@gmail.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Passes input_id struct to the common probe function for the tsc200x drivers
instead of just the bustype.
This allows for the use of the product variable to set the input_dev->name
variable according to the type of touchscreen used. Note that when we
introduced support for TSC2004 we started calling everything TSC200X, so
let's keep this quirk.
Signed-off-by: Michael Welling <mwelling@ieee.org> Acked-by: Pavel Machek <pavel@ucw.cz> Acked-by: Pali Rohár <pali.rohar@gmail.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Xbox One controllers have multiple interfaces which all have the
same class, subclass, and protocol. One of the these interfaces
has only a single endpoint. When Xpad attempts to bind to this
interface, it causes an oops when trying initialize the output URB
by trying to access the second endpoint's descriptor.
This situation was avoided for known Xbox One devices by checking
the XTYPE constant associated with the VID and PID tuple. However,
this breaks when new or previously unknown Xbox One controllers
are attached to the system.
This change addresses the problem by deriving the XTYPE for Xbox
One controllers based on the interface protocol before checking
the interface number.
Fixes: 1a48ff81b391 ("Input: xpad - add support for Xbox One controllers") Signed-off-by: Cameron Gutman <aicommander@gmail.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
The touchpad in HP Pavilion 14-ab057ca reports it's version as 12 and
according to Elan both 11 and 12 are valid IC types and should be
identified as hw_version 4.
Reported-by: Patrick Lessard <Patrick.Lessard@cogeco.com> Tested-by: Patrick Lessard <Patrick.Lessard@cogeco.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
The VMWare EFI BIOS will expose port 0x5658 as an ACPI resource. This
causes the port to be reserved by the APCI module as the system comes up,
making it unavailable to be reserved again by other drivers, thus
preserving this VMWare port for special use in a VMWare guest.
This port is designed to be shared among multiple VMWare services, such as
the VMMOUSE. Because of this, VMMOUSE should not try to reserve this port
on its own.
The VMWare non-EFI BIOS does not do this to preserve compatibility with
existing/legacy VMs. It is known that there is small chance a VM may be
configured such that these ports get reserved by other non-VMWare devices,
and if this ever happens, the result is undefined.
Signed-off-by: Sinclair Yeh <syeh@vmware.com> Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
xenbus_dev_request_and_reply() needs to track whether a transaction is
open. For XS_TRANSACTION_START messages it calls transaction_start()
and for XS_TRANSACTION_END messages it calls transaction_end().
If sending an XS_TRANSACTION_START message fails or responds with an
an error, the transaction is not open and transaction_end() must be
called.
If sending an XS_TRANSACTION_END message fails, the transaction is
still open, but if an error response is returned the transaction is
closed.
Commit 027bd7e89906 ("xen/xenbus: Avoid synchronous wait on XenBus
stalling shutdown/restart") introduced a regression where failed
XS_TRANSACTION_START messages were leaving the transaction open. This
can cause problems with suspend (and migration) as all transactions
must be closed before suspending.
It appears that the problematic change was added accidentally, so just
remove it.
Signed-off-by: Jan Beulich <jbeulich@suse.com> Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: David Vrabel <david.vrabel@citrix.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Inability to locate a user mode specified transaction ID should not
lead to a kernel crash. For other than XS_TRANSACTION_START also
don't issue anything to xenbus if the specified ID doesn't match that
of any active transaction.
Signed-off-by: Jan Beulich <jbeulich@suse.com> Signed-off-by: David Vrabel <david.vrabel@citrix.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Current overlap check is evaluating to false a case where a filter
field is fully contained (proper subset) of a r/w request. This
change applies classical overlap check instead to include all the
scenarios.
More specifically, for (Hilscher GmbH CIFX 50E-DP(M/S)) device driver
the logic is such that the entire confspace is read and written in 4
byte chunks. In this case as an example, CACHE_LINE_SIZE,
LATENCY_TIMER and PCI_BIST are arriving together in one call to
xen_pcibk_config_write() with offset == 0xc and size == 4. With the
exsisting overlap check the LATENCY_TIMER field (offset == 0xd, length
== 1) is fully contained in the write request and hence is excluded
from write, which is incorrect.
Signed-off-by: Andrey Grodzovsky <andrey2805@gmail.com> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Reviewed-by: Jan Beulich <JBeulich@suse.com> Signed-off-by: David Vrabel <david.vrabel@citrix.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
With recent binutils update to support dwarf CFI pseudo-ops in gas, we
now get .eh_frame vs. .debug_frame. Although the call frame info is
exactly the same in both, the CIE differs, which the current kernel
unwinder can't cope with.
This broke both the kernel unwinder as well as loadable modules (latter
because of a new unhandled relo R_ARC_32_PCREL from .rela.eh_frame in
the module loader)
The ideal solution would be to switch unwinder to .eh_frame.
For now however we can make do by just ensureing .debug_frame is
generated by removing -fasynchronous-unwind-tables
.eh_frame generated with -gdwarf-2 -fasynchronous-unwind-tables
.debug_frame generated with -gdwarf-2
If CONFIG_ARC_DW2_UNWIND is disabled every time arc_unwind_core()
gets called following message gets printed in debug console:
----------------->8---------------
CONFIG_ARC_DW2_UNWIND needs to be enabled
----------------->8---------------
That message makes sense if user indeed wants to see a backtrace or
get nice function call-graphs in perf but what if user disabled
unwinder for the purpose? Why pollute his debug console?
So instead we'll warn user about possibly missing feature once and
let him decide if that was what he or she really wanted.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Signed-off-by: Vineet Gupta <vgupta@synopsys.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Lengthy output of sysrq-w may take a lot of time on slow serial console.
Currently we reset NMI-watchdog on the current CPU to avoid spurious
lockup messages. Sometimes this doesn't work since softlockup watchdog
might trigger on another CPU which is waiting for an IPI to proceed.
We reset softlockup watchdogs on all CPUs, but we do this only after
listing all tasks, and this may be too late on a busy system.
So, reset watchdogs CPUs earlier, in for_each_process_thread() loop.
Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/1465474805-14641-1-git-send-email-aryabinin@virtuozzo.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
If CONFIG_KASAN is enabled and gcc is configured with
--disable-initfini-array and/or gold linker is used, gcc emits
.ctors/.dtors and .text.startup/.text.exit sections instead of
.init_array/.fini_array. .dtors section is not explicitly accounted in
the linker script and messes vvar/percpu layout.
early_page_uninitialised looks up an arbitrary PFN. While a machine
without node 0 will boot with "mm, page_alloc: Always return a valid
node from early_pfn_to_nid", it works because it assumes that nodes are
always in PFN order. This is not guaranteed so this patch adds
robustness by always checking if the node being checked is online.
Link: http://lkml.kernel.org/r/1468008031-3848-4-git-send-email-mgorman@techsingularity.net Signed-off-by: Mel Gorman <mgorman@techsingularity.net> Acked-by: David Rientjes <rientjes@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
early_pfn_to_nid can return node 0 if a PFN is invalid on machines that
has no node 0. A machine with only node 1 was observed to crash with
the following message:
The problem is that early_page_uninitialised uses the early_pfn_to_nid
helper which returns node 0 for invalid PFNs. No caller of
early_pfn_to_nid cares except early_page_uninitialised. This patch has
early_pfn_to_nid always return a valid node.
Link: http://lkml.kernel.org/r/1468008031-3848-3-git-send-email-mgorman@techsingularity.net Signed-off-by: Mel Gorman <mgorman@techsingularity.net> Acked-by: David Rientjes <rientjes@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
It's possible to isolate some freepages in a pageblock and then fail
split_free_page() due to the low watermark check. In this case, we hit
VM_BUG_ON() because the freeing scanner terminated early without a
contended lock or enough freepages.
This should never have been a VM_BUG_ON() since it's not a fatal
condition. It should have been a VM_WARN_ON() at best, or even handled
gracefully.
Regardless, we need to terminate anytime the full pageblock scan was not
done. The logic belongs in isolate_freepages_block(), so handle its
state gracefully by terminating the pageblock loop and making a note to
restart at the same pageblock next time since it was not possible to
complete the scan this time.
[rientjes@google.com: don't rescan pages in a pageblock] Link: http://lkml.kernel.org/r/alpine.DEB.2.10.1607111244150.83138@chino.kir.corp.google.com Link: http://lkml.kernel.org/r/alpine.DEB.2.10.1606291436300.145590@chino.kir.corp.google.com Signed-off-by: David Rientjes <rientjes@google.com> Reported-by: Minchan Kim <minchan@kernel.org> Tested-by: Minchan Kim <minchan@kernel.org> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Hugh Dickins <hughd@google.com> Cc: Mel Gorman <mgorman@techsingularity.net> Cc: Vlastimil Babka <vbabka@suse.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
The value `bytes' comes from the filesystem which is about to be
mounted. We cannot trust that the value is always in the range we
expect it to be.
Check its value before using it to calculate the length for the crc32_le
call. It value must be larger (or equal) sumoff + 4.
This fixes a kernel bug when accidentially mounting an image file which
had the nilfs2 magic value 0x3434 at the right offset 0x406 by chance.
The bytes 0x01 0x00 were stored at 0x408 and were interpreted as a
s_bytes value of 1. This caused an underflow when substracting sumoff +
4 (20) in the call to crc32_le.
If the memory compaction free scanner cannot successfully split a free
page (only possible due to per-zone low watermark), terminate the free
scanner rather than continuing to scan memory needlessly. If the
watermark is insufficient for a free page of order <= cc->order, then
terminate the scanner since all future splits will also likely fail.
This prevents the compaction freeing scanner from scanning all memory on
very large zones (very noticeable for zones > 128GB, for instance) when
all splits will likely fail while holding zone->lock.
compaction_alloc() iterating a 128GB zone has been benchmarked to take
over 400ms on some systems whereas any free page isolated and ready to
be split ends up failing in split_free_page() because of the low
watermark check and thus the iteration continues.
The next time compaction occurs, the freeing scanner will likely start
at the end of the zone again since no success was made previously and we
get the same lengthy iteration until the zone is brought above the low
watermark. All thp page faults can take >400ms in such a state without
this fix.
Link: http://lkml.kernel.org/r/alpine.DEB.2.10.1606211820350.97086@chino.kir.corp.google.com Signed-off-by: David Rientjes <rientjes@google.com> Acked-by: Vlastimil Babka <vbabka@suse.cz> Cc: Minchan Kim <minchan@kernel.org> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Mel Gorman <mgorman@techsingularity.net> Cc: Hugh Dickins <hughd@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Commit d0164adc89f6 ("mm, page_alloc: distinguish between being unable
to sleep, unwilling to sleep and avoiding waking kswapd") modified
__GFP_WAIT to explicitly identify the difference between atomic callers
and those that were unwilling to sleep. Later the definition was
removed entirely.
The GFP_RECLAIM_MASK is the set of flags that affect watermark checking
and reclaim behaviour but __GFP_ATOMIC was never added. Without it,
atomic users of the slab allocator strip the __GFP_ATOMIC flag and
cannot access the page allocator atomic reserves. This patch addresses
the problem.
The user-visible impact depends on the workload but potentially atomic
allocations unnecessarily fail without this path.
Link: http://lkml.kernel.org/r/20160610093832.GK2527@techsingularity.net Signed-off-by: Mel Gorman <mgorman@techsingularity.net> Reported-by: Marcin Wojtas <mw@semihalf.com> Acked-by: Vlastimil Babka <vbabka@suse.cz> Acked-by: Michal Hocko <mhocko@suse.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Due to the way CUBC register is updated, a double flush is needed to
compute an accurate residue. First flush aim is to get data from the DMA
FIFO and second one ensures that we won't report data which are not in
memory.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com> Fixes: e1f7c9eee707 ("dmaengine: at_xdmac: creation of the atmel
eXtended DMA Controller driver") Reviewed-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
The EFI firmware on Macs contains a full-fledged network stack for
downloading OS X images from osrecovery.apple.com. Unfortunately
on Macs introduced 2011 and 2012, EFI brings up the Broadcom 4331
wireless card on every boot and leaves it enabled even after
ExitBootServices has been called. The card continues to assert its IRQ
line, causing spurious interrupts if the IRQ is shared. It also corrupts
memory by DMAing received packets, allowing for remote code execution
over the air. This only stops when a driver is loaded for the wireless
card, which may be never if the driver is not installed or blacklisted.
The issue seems to be constrained to the Broadcom 4331. Chris Milsted
has verified that the newer Broadcom 4360 built into the MacBookPro11,3
(2013/2014) does not exhibit this behaviour. The chances that Apple will
ever supply a firmware fix for the older machines appear to be zero.
The solution is to reset the card on boot by writing to a reset bit in
its mmio space. This must be done as an early quirk and not as a plain
vanilla PCI quirk to successfully combat memory corruption by DMAed
packets: Matthew Garrett found out in 2012 that the packets are written
to EfiBootServicesData memory (http://mjg59.dreamwidth.org/11235.html).
This type of memory is made available to the page allocator by
efi_free_boot_services(). Plain vanilla PCI quirks run much later, in
subsys initcall level. In-between a time window would be open for memory
corruption. Random crashes occurring in this time window and attributed
to DMAed packets have indeed been observed in the wild by Chris
Bainbridge.
When Matthew Garrett analyzed the memory corruption issue in 2012, he
sought to fix it with a grub quirk which transitions the card to D3hot:
http://git.savannah.gnu.org/cgit/grub.git/commit/?id=9d34bb85da56
This approach does not help users with other bootloaders and while it
may prevent DMAed packets, it does not cure the spurious interrupts
emanating from the card. Unfortunately the card's mmio space is
inaccessible in D3hot, so to reset it, we have to undo the effect of
Matthew's grub patch and transition the card back to D0.
Note that the quirk takes a few shortcuts to reduce the amount of code:
The size of BAR 0 and the location of the PM capability is identical
on all affected machines and therefore hardcoded. Only the address of
BAR 0 differs between models. Also, it is assumed that the BCMA core
currently mapped is the 802.11 core. The EFI driver seems to always take
care of this.
Michael Büsch, Bjorn Helgaas and Matt Fleming contributed feedback
towards finding the best solution to this problem.
The following should be a comprehensive list of affected models:
iMac13,1 2012 21.5" [Root Port 00:1c.3 = 8086:1e16]
iMac13,2 2012 27" [Root Port 00:1c.3 = 8086:1e16]
Macmini5,1 2011 i5 2.3 GHz [Root Port 00:1c.1 = 8086:1c12]
Macmini5,2 2011 i5 2.5 GHz [Root Port 00:1c.1 = 8086:1c12]
Macmini5,3 2011 i7 2.0 GHz [Root Port 00:1c.1 = 8086:1c12]
Macmini6,1 2012 i5 2.5 GHz [Root Port 00:1c.1 = 8086:1e12]
Macmini6,2 2012 i7 2.3 GHz [Root Port 00:1c.1 = 8086:1e12]
MacBookPro8,1 2011 13" [Root Port 00:1c.1 = 8086:1c12]
MacBookPro8,2 2011 15" [Root Port 00:1c.1 = 8086:1c12]
MacBookPro8,3 2011 17" [Root Port 00:1c.1 = 8086:1c12]
MacBookPro9,1 2012 15" [Root Port 00:1c.1 = 8086:1e12]
MacBookPro9,2 2012 13" [Root Port 00:1c.1 = 8086:1e12]
MacBookPro10,1 2012 15" [Root Port 00:1c.1 = 8086:1e12]
MacBookPro10,2 2012 13" [Root Port 00:1c.1 = 8086:1e12]
For posterity, spurious interrupts caused by the Broadcom 4331 wireless
card resulted in splats like this (stacktrace omitted):
We used to scan secondary buses until the following commit that
was applied in 2009:
8659c406ade3 ("x86: only scan the root bus in early PCI quirks")
which commit constrained early quirks to the root bus only. Its
motivation was to prevent application of the nvidia_bugs quirk
on secondary buses.
We're about to add a quirk to reset the Broadcom 4331 wireless card on
2011/2012 Macs, which is located on a secondary bus behind a PCIe root
port. To facilitate that, reintroduce scanning of secondary buses.
The commit message of 8659c406ade3 notes that scanning only the root bus
"saves quite some unnecessary scanning work". The algorithm used prior
to 8659c406ade3 was particularly time consuming because it scanned
buses 0 to 31 brute force. To avoid lengthening boot time, employ a
recursive strategy which only scans buses that are actually reachable
from the root bus.
Yinghai Lu pointed out that the secondary bus number read from a
bridge's config space may be invalid, in particular a value of 0 would
cause an infinite loop. The PCI core goes beyond that and recurses to a
child bus only if its bus number is greater than the parent bus number
(see pci_scan_bridge()). Since the root bus is numbered 0, this implies
that secondary buses may not be 0. Do the same on early scanning.
If this algorithm is found to significantly impact boot time or cause
infinite loops on broken hardware, it would be possible to limit its
recursion depth: The Broadcom 4331 quirk applies at depth 1, all others
at depth 0, so the bus need not be scanned deeper than that for now. An
alternative approach would be to revert to scanning only the root bus,
and apply the Broadcom 4331 quirk to the root ports 8086:1c12, 8086:1e12
and 8086:1e16. Apple always positioned the card behind either of these
three ports. The quirk would then check presence of the card in slot 0
below the root port and do its deed.
Signed-off-by: Lukas Wunner <lukas@wunner.de> Cc: Andy Lutomirski <luto@kernel.org> Cc: Bjorn Helgaas <bhelgaas@google.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Yinghai Lu <yinghai@kernel.org> Cc: linux-pci@vger.kernel.org Link: http://lkml.kernel.org/r/f0daa70dac1a9b2483abdb31887173eb6ab77bdf.1465690253.git.lukas@wunner.de Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
8659c406ade3 ("x86: only scan the root bus in early PCI quirks")
... early quirks are only applied to devices on the root bus.
The motivation was to prevent application of the nvidia_bugs quirk on
secondary buses.
We're about to reintroduce scanning of secondary buses for a quirk to
reset the Broadcom 4331 wireless card on 2011/2012 Macs. To prevent
regressions, open code the requirement to apply nvidia_bugs only on the
root bus.
Signed-off-by: Lukas Wunner <lukas@wunner.de> Cc: Andy Lutomirski <luto@kernel.org> Cc: Bjorn Helgaas <bhelgaas@google.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Yinghai Lu <yinghai@kernel.org> Link: http://lkml.kernel.org/r/4d5477c1d76b2f0387a780f2142bbcdd9fee869b.1465690253.git.lukas@wunner.de Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Since ed_schedule begins with marking the ED as "operational",
the ED may be left in such state even if scheduling actually
fails.
This allows future submission attempts to smuggle this ED to the
hardware behind the scheduler's back and without linking it to
the ohci->eds_in_use list.
The former causes bandwidth saturation and data loss on isoc
endpoints, the latter crashes the kernel when attempt is made
to unlink such ED from this list.
Fix ed_schedule to update ED state only on successful return.
Signed-off-by: Michal Pecio <michal.pecio@gmail.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
UBUNTU: SAUCE: pinctrl/amd: Remove the default de-bounce time
In the function amd_gpio_irq_enable and amd_gpio_direction_input, remove the code which is setting the default de-bounce time to 2.75ms.
The driver code shall use the same settings as specified in BIOS.
Any default assignment impacts TouchPad behaviour when the LevelTrig is set to EDGE FALLING.
The original patch: http://www.spinics.net/lists/stable/msg139761.html
BugLink: http://bugs.launchpad.net/bugs/1612006 Reviewed-by: Ken Xue <Ken.Xue@amd.com> Signed-off-by: Nitesh Kumar Agrawal <Nitesh-kumar.Agrawal@amd.com> Signed-off-by: Alex Hung <alex.hung@canonical.com> Acked-by: Stefan Bader <stefan.bader@caonical.com> Acked-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@caonical.com>
Eric Dumazet [Sun, 10 Jul 2016 08:04:02 +0000 (10:04 +0200)]
tcp: make challenge acks less predictable
Yue Cao claims that current host rate limiting of challenge ACKS
(RFC 5961) could leak enough information to allow a patient attacker
to hijack TCP sessions. He will soon provide details in an academic
paper.
This patch increases the default limit from 100 to 1000, and adds
some randomization so that the attacker can no longer hijack
sessions without spending a considerable amount of probes.
Based on initial analysis and patch from Linus.
Note that we also have per socket rate limiting, so it is tempting
to remove the host limit in the future.
v2: randomize the count of challenge acks per second, not the period.
Fixes: 282f23c6ee34 ("tcp: implement RFC 5961 3.2") Reported-by: Yue Cao <ycao009@ucr.edu> Signed-off-by: Eric Dumazet <edumazet@google.com> Suggested-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Yuchung Cheng <ycheng@google.com> Cc: Neal Cardwell <ncardwell@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Acked-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
CVE-2016-5696
(backported from commit 75ff39ccc1bd5d3c455b6822ab09e533c551f758 upstream) Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Luis Henriques <luis.henriques@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
drm/i915/edp: Add WaKVMNotificationOnConfigChange:bdw
- it's only for BDW which doesn't use i915_bpo
drm/i915/skl: Add WAC6entrylatency
- it didn't end up in 4.7
Signed-off-by: Timo Aaltonen <timo.aaltonen@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
What looked like bugs at the time (a 2nd allocation was triggered
but failed, reset was called regardless of previous failures, and
errors have not been reported to userspace) was actually something
at least one userspace tool depended on. Restore that behavior in
a sane way.
Fixes: 1bc6664bdfb ("s390/cio: use device_lock during cmb activation") Cc: stable@vger.kernel.org #v4.4+ Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com> Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com> Reviewed-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
(cherry picked from commit 0f5d050ceaa31b2229102211d60c149f920df3aa) Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Michael Neuling [Mon, 1 Aug 2016 14:08:04 +0000 (08:08 -0600)]
powerpc/tm: Fix stack pointer corruption in __tm_recheckpoint()
BugLink: http://bugs.launchpad.net/bugs/1606786
At the start of __tm_recheckpoint() we save the kernel stack pointer
(r1) in SPRG SCRATCH0 (SPRG2) so that we can restore it after the
trecheckpoint.
Unfortunately, the same SPRG is used in the SLB miss handler. If an
SLB miss is taken between the save and restore of r1 to the SPRG, the
SPRG is changed and hence r1 is also corrupted. We can end up with
the following crash when we start using r1 again after the restore
from the SPRG:
Michael Neuling [Mon, 1 Aug 2016 14:08:03 +0000 (08:08 -0600)]
powerpc/tm: Avoid SLB faults in treclaim/trecheckpoint when RI=0
BugLink: http://bugs.launchpad.net/bugs/1606786
Currently we have 2 segments that are bolted for the kernel linear
mapping (ie 0xc000... addresses). This is 0 to 1TB and also the kernel
stacks. Anything accessed outside of these regions may need to be
faulted in. (In practice machines with TM always have 1T segments)
If a machine has < 2TB of memory we never fault on the kernel linear
mapping as these two segments cover all physical memory. If a machine
has > 2TB of memory, there may be structures outside of these two
segments that need to be faulted in. This faulting can occur when
running as a guest as the hypervisor may remove any SLB that's not
bolted.
When we treclaim and trecheckpoint we have a window where we need to
run with the userspace GPRs. This means that we no longer have a valid
stack pointer in r1. For this window we therefore clear MSR RI to
indicate that any exceptions taken at this point won't be able to be
handled. This means that we can't take segment misses in this RI=0
window.
In this RI=0 region, we currently access the thread_struct for the
process being context switched to or from. This thread_struct access
may cause a segment fault since it's not guaranteed to be covered by
the two bolted segment entries described above.
We've seen this with a crash when running as a guest with > 2TB of
memory on PowerVM:
This fixes this by copying the required data from the thread_struct to
the stack before we clear MSR RI. Then once we clear RI, we only access
the stack, guaranteeing there's no segment miss.
We also tighten the region over which we set RI=0 on the treclaim()
path. This may have a slight performance impact since we're adding an
mtmsr instruction.
Fixes: 090b9284d725 ("powerpc/tm: Clear MSR RI in non-recoverable TM code") Signed-off-by: Michael Neuling <mikey@neuling.org> Reviewed-by: Cyril Bur <cyrilbur@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
(cherry picked from commit 190ce8693c23eae09ba5f303a83bf2fbeb6478b1) Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
AceLan Kao [Wed, 3 Aug 2016 02:31:12 +0000 (10:31 +0800)]
intel-vbtn: new driver for Intel Virtual Button
BugLink: https://bugs.launchpad.net/bugs/1609204
This driver supports power button event in Intel Virtual Button currently.
New Dell XPS 13 requires this driver for the power button.
This driver is copied/modified from intel-hid.c
Most credit goes to the author of intel-hid.c,
Alex Hung <alex.hung@canonical.com>
Signed-off-by: AceLan Kao <acelan.kao@canonical.com> Signed-off-by: Darren Hart <dvhart@linux.intel.com>
(cherry picked from commit 332e081225fc2a657aa587c42943d5f5a7dae88b) Signed-off-by: AceLan Kao <acelan.kao@canonical.com> Acked-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
BugLink: http://bugs.launchpad.net/bugs/1608762
Dell Optiplex 7450 AIO works with BOOT_ACPI; however, the quirk for
"OptiPlex 745" changes its boot method to BOOT_BIOS and causes 7450 AIO
hangs when rebooting; as a result, 7450 AIO is appended to overwrite
BOOT_BIOS by BOOT_ACPI in order not to break the original 745 series
Signed-off-by: Alex Hung <alex.hung@canonical.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-kernel@vger.kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
(cherry picked from commit 4d581259b7d44c8120a614b4e9244094c824d51f) Signed-off-by: Alex Hung <alex.hung@canonical.com> Acked-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Kamal Mostafa [Fri, 29 Jul 2016 18:01:30 +0000 (11:01 -0700)]
UBUNTU: SAUCE: xhci: Fix soft lockup in xhci_pci_probe path when XHCI_STATE_HALTED
Commit 27a41a83ec54 ("xhci: Cleanup only when releasing primary hcd")
causes a soft lockup at boot when XHCI_STATE_HALTED, preventing
VirtualBox 5.1.x from booting if USB3.0 is enabled.
Revert to allowing xhci_irq to handle the interrupt when
XHCI_STATE_HALTED but not XHCI_STATE_DYING.
Fixes: 27a41a83ec54 ("xhci: Cleanup only when releasing primary hcd") BugLink: https://bugs.launchpad.net/bugs/1604058 Signed-off-by: Kamal Mostafa <kamal@canonical.com> Cc: <stable@vger.kernel.org> #v4.3+ Cc: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com> Acked-by: Tim Gardner <tim.gardner@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com>
BugLink: http://bugs.launchpad.net/bugs/1597908
Timer context is not very useful for drivers to perform any meaningful abort
action from. So instead of calling the driver from this useless context
defer it to a workqueue as soon as possible.
Note that while a delayed_work item would seem the right thing here I didn't
dare to use it due to the magic in blk_add_timer that pokes deep into timer
internals. But maybe this encourages Tejun to add a sensible API for that to
the workqueue API and we'll all be fine in the end :)
Contains a major update from Keith Bush:
"This patch removes synchronizing the timeout work so that the timer can
start a freeze on its own queue. The timer enters the queue, so timer
context can only start a freeze, but not wait for frozen."
Signed-off-by: Christoph Hellwig <hch@lst.de> Acked-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Jens Axboe <axboe@fb.com>
(cherry picked from commit 287922eb0b186e2a5bf54fdd04b734c25c90035c) Signed-off-by: Joseph Salisbury <joseph.salisbury@canonical.com> Acked-by: Tim Gardner <tim.gardner@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Jesse Gross [Sat, 19 Mar 2016 16:32:02 +0000 (09:32 -0700)]
tunnels: Remove encapsulation offloads on decap.
If a packet is either locally encapsulated or processed through GRO
it is marked with the offloads that it requires. However, when it is
decapsulated these tunnel offload indications are not removed. This
means that if we receive an encapsulated TCP packet, aggregate it with
GRO, decapsulate, and retransmit the resulting frame on a NIC that does
not support encapsulation, we won't be able to take advantage of hardware
offloads even though it is just a simple TCP packet at this point.
This fixes the problem by stripping off encapsulation offload indications
when packets are decapsulated.
The performance impacts of this bug are significant. In a test where a
Geneve encapsulated TCP stream is sent to a hypervisor, GRO'ed, decapsulated,
and bridged to a VM performance is improved by 60% (5Gbps->8Gbps) as a
result of avoiding unnecessary segmentation at the VM tap interface.
Reported-by: Ramu Ramamurthy <sramamur@linux.vnet.ibm.com> Fixes: 68c33163 ("v4 GRE: Add TCP segmentation offload for GRE") Signed-off-by: Jesse Gross <jesse@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> BugLink: http://bugs.launchpad.net/bugs/1602755
(backported from commit a09a4c8dd1ec7f830e1fb9e59eb72bddc965d168)
[adapt iptunnel_pull_header arguments, avoid 7f290c9] Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Andy Whitcroft <apw@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
be2net: perform temperature query in adapter regardless of its interface state
BugLink: http://bugs.launchpad.net/bugs/1607387
The be2net driver performs fw temperature queries on be_worker() routine,
which is executed each second for each be_adapter. There is a frequency
threshold to avoid fw query to happens at each call to be_worker();
instead, currently a fw query occurs once in 64 runs of the procedure.
Nevertheless, this fw temperature query is invoked only for adapters which
interface is up, so we can see I/O errors on read of hwmon counters from
userspace (from tools like lm-sensors) in case we have adapters' functions
which interface is down.
This patch moves the fw query code to be invoked even if interface is down.
No functional changes were introduced.
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com> Acked-by: Sathya Perla <sathya.perla@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
(cherry picked from commit d3480615cf00c6f615cdb61a9d03386574b93342) Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
r8152: Add support for setting pass through MAC address on RTL8153-AD
BugLink: http://bugs.launchpad.net/bugs/1579984
The RTL8153-AD supports a persistent system specific MAC address.
This means a device plugged into two different systems with host side
support will show different (but persistent) MAC addresses.
This information for the system's persistent MAC address is burned in when
the system HW is built and available under \_SB.AMAC in the DSDT at runtime.
This technology is currently implemented in the Dell TB15 and WD15 Type-C
docks. More information is available here:
http://www.dell.com/support/article/us/en/04/SLN301147
Signed-off-by: Mario Limonciello <mario_limonciello@dell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
(back ported from commit 34ee32c9a5696247be405bb0c21f3d1fc6cb5729) Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Conflicts:
drivers/net/usb/r8152.c
Acked-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Reported-by: Subbarao Narahari <snarahari@vmware.com> Signed-off-by: Shrikrishna Khare <skhare@vmware.com> Signed-off-by: Jin Heo <heoj@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net>
(back ported from commit f0d437809d23999cb25207cfbe80c61e5703fdc1) Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Conflicts:
drivers/net/vmxnet3/vmxnet3_int.h
Acked-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
UBUNTU: SAUCE: lpfc: fix oops in lpfc_sli4_scmd_to_wqidx_distr() from lpfc_send_taskmgmt()
BugLink: http://bugs.launchpad.net/bugs/1597974
The lpfc_sli4_scmd_to_wqidx_distr() function expects the scsi_cmnd
'lpfc_cmd->pCmd' not to be null, and point to the midlayer command.
That's not true in the .eh_(device|target|bus)_reset_handler path,
because lpfc_send_taskmgmt() sends commands not from the midlayer,
so does not set 'lpfc_cmd->pCmd'.
That is true in the .queuecommand path because lpfc_queuecommand()
stores the scsi_cmnd from midlayer in lpfc_cmd->pCmd; and lpfc_cmd
is stored by lpfc_scsi_prep_cmnd() in piocbq->context1 -- which is
passed to lpfc_sli4_scmd_to_wqidx_distr() as lpfc_cmd parameter.
This problem can be hit on SCSI EH, and immediately with sg_reset.
These 2 test-cases demonstrate the problem/fix with next-20160601.
Fixes: 8b0dff14164d ("lpfc: Add support for using block multi-queue") Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com> Signed-off-by: James Smart <james.smart@broadcom.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Uma Krishnan [Fri, 22 Jul 2016 14:58:31 +0000 (07:58 -0700)]
UBUNTU: SAUCE: cxlflash: Verify problem state area is mapped before notifying shutdown
BugLink: http://bugs.launchpad.net/bugs/1605405
If an EEH or some other hard error occurs while the
adapter instance was being initialized, on the subsequent
shutdown of the device, the system could crash with:
This crash is due to the AFU not being mapped when the shutdown
notification routine is called and is a regression that was inserted
recently with Commit 704c4b0ddc03 ("cxlflash: Shutdown notify support
for CXL Flash cards").
As a fix, shutdown notification should only occur when the AFU is mapped.
Fixes: 704c4b0ddc03 ("cxlflash: Shutdown notify support for CXL Flash cards") Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
BugLink: http://bugs.launchpad.net/bugs/1607404 Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Unlink and rename in overlayfs checked the upper dentry for staleness by
verifying upper->d_parent against upperdir. However the dentry can go
stale also by being unhashed, for example.
Expand the verification to actually look up the name again (under parent
lock) and check if it matches the upper dentry. This matches what the VFS
does before passing the dentry to filesytem's unlink/rename methods, which
excludes any inconsistency caused by overlayfs.
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
It has been found out that in some HW combination the DisplayPort
fast link training feature caused screen flickering. Let's revert
this feature for now until we can ensure that the feature works for
all platforms.
This is a manual revert of commits 5fa836a9d859 ("drm/i915: DP link
training optimization") and 4e96c97742f4 ("drm/i915: eDP link training
optimization").
Fixes: 5fa836a9d859 ("drm/i915: DP link training optimization") Fixes: 4e96c97742f4 ("drm/i915: eDP link training optimization")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91393 Reviewed-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1466410226-19543-1-git-send-email-mika.kahola@intel.com
(cherry picked from commit 91df09d92ad82c8778ca218097bf827f154292ca) Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
The well-spotted fallocate undo fix is good in most cases, but not when
fallocate failed on the very first page. index 0 then passes lend -1
to shmem_undo_range(), and that has two bad effects: (a) that it will
undo every fallocation throughout the file, unrestricted by the current
range; but more importantly (b) it can cause the undo to hang, because
lend -1 is treated as truncation, which makes it keep on retrying until
every page has gone, but those already fully instantiated will never go
away. Big thank you to xfstests generic/269 which demonstrates this.
Fixes: b9b4bb26af01 ("tmpfs: don't undo fallocate past its last page") Signed-off-by: Hugh Dickins <hughd@google.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
When fallocate is interrupted it will undo a range that extends one byte
past its range of allocated pages. This can corrupt an in-use page by
zeroing out its first byte. Instead, undo using the inclusive byte
range.
Fixes: 1635f6a74152f1d ("tmpfs: undo fallocation on failure") Link: http://lkml.kernel.org/r/1462713387-16724-1-git-send-email-anthony.romano@coreos.com Signed-off-by: Anthony Romano <anthony.romano@coreos.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Hugh Dickins <hughd@google.com> Cc: Brandon Philips <brandon@ifup.co> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Parallel build can sporadically fail because asn1 headers may
not be built yet by the time qat_asym_algs.o is compiled:
drivers/crypto/qat/qat_common/qat_asym_algs.c:55:32: fatal error: qat_rsapubkey-asn1.h: No such file or directory
#include "qat_rsapubkey-asn1.h"
Signed-off-by: Jan Stancek <jstancek@redhat.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
As of Xen 4.7 PV CPUID doesn't expose either of CPUID[1].ECX[7] and
CPUID[0x80000007].EDX[7] anymore, causing the driver to fail to load on
both Intel and AMD systems. Doing any kind of hardware capability
checks in the driver as a prerequisite was wrong anyway: With the
hypervisor being in charge, all such checking should be done by it. If
ACPI data gets uploaded despite some missing capability, the hypervisor
is free to ignore part or all of that data.
Ditch the entire check_prereq() function, and do the only valid check
(xen_initial_domain()) in the caller in its place.
Signed-off-by: Jan Beulich <jbeulich@suse.com> Signed-off-by: David Vrabel <david.vrabel@citrix.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
POSIX allows files with trailing spaces or a trailing period but
SMB3 does not, so convert these using the normal Services For Mac
mapping as we do for other reserved characters such as
: < > | ? *
This is similar to what Macs do for the same problem over SMB3.
Signed-off-by: Steve French <steve.french@primarydata.com> Acked-by: Pavel Shilovsky <pshilovsky@samba.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
In sess_auth_rawntlmssp_authenticate(), the ntlmssp blob is allocated
statically and its size is an "empirical" 5*sizeof(struct
_AUTHENTICATE_MESSAGE) (320B on x86_64). I don't know where this value
comes from or if it was ever appropriate, but it is currently
insufficient: the user and domain name in UTF16 could take 1kB by
themselves. Because of that, build_ntlmssp_auth_blob() might corrupt
memory (out-of-bounds write). The size of ntlmssp_blob in
SMB2_sess_setup() is too small too (sizeof(struct _NEGOTIATE_MESSAGE)
+ 500).
This patch allocates the blob dynamically in
build_ntlmssp_auth_blob().
Signed-off-by: Jerome Marchand <jmarchan@redhat.com> Signed-off-by: Steve French <smfrench@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Azure server blocks clients that open a socket and don't do anything on it.
In our reconnect scenarios, we can reconnect the tcp session and
detect the socket is available but we defer the negprot and SMB3 session
setup and tree connect reconnection until the next i/o is requested, but
this looks suspicous to some servers who expect SMB3 negprog and session
setup soon after a socket is created.
In the echo thread, reconnect SMB3 sessions and tree connections
that are disconnected. A later patch will replay persistent (and
resilient) handle opens.
Signed-off-by: Steve French <steve.french@primarydata.com> Acked-by: Pavel Shilovsky <pshilovsky@samba.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
The untagged command case in the 53c700 driver has been broken since
host wide tags were enabled because the replaced scsi_find_tag()
function had a special case for the tag value SCSI_NO_TAG to retrieve
sdev->current_cmnd. The replacement function scsi_host_find_tag() has
no such special case and returns NULL causing untagged commands to
trigger a BUG() in the driver. Inspection shows that the 53c700 is the
only driver using this SCSI_NO_TAG case, so a local fix in the driver
suffices to fix this problem globally.
Fixes: 64d513ac31b - "scsi: use host wide tags by default" Reported-by: Helge Deller <deller@gmx.de> Tested-by: Helge Deller <deller@gmx.de> Signed-off-by: James Bottomley <jejb@linux.vnet.ibm.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Ewan D. Milne <emilne@redhat.com> Acked-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
sas_ata_strategy_handler() adds the works of the ata error handler to
system_unbound_wq. This workqueue asynchronously runs work items, so the
ata error handler will be performed concurrently on different CPUs. In
this case, ->host_failed will be decreased simultaneously in
scsi_eh_finish_cmd() on different CPUs, and become abnormal.
It will lead to permanently inequality between ->host_failed and
->host_busy, and scsi error handler thread won't start running. IO
errors after that won't be handled.
Since all scmds must have been handled in the strategy handler, just
remove the decrement in scsi_eh_finish_cmd() and zero ->host_busy after
the strategy handler to fix this race.
Fixes: 50824d6c5657 ("[SCSI] libsas: async ata-eh") Signed-off-by: Wei Fang <fangwei1@huawei.com> Reviewed-by: James Bottomley <jejb@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
The upper dentry may become stale before we call ovl_lock_rename_workdir.
For example, someone could (mistakenly or maliciously) manually unlink(2)
it directly from upperdir.
To ensure it is not stale, let's lookup it after ovl_lock_rename_workdir
and and check if it matches the upper dentry.
Essentially, it is the same problem and similar solution as in
commit 11f3710417d0 ("ovl: verify upper dentry before unlink and rename").
Signed-off-by: Maxim Patlasov <mpatlasov@virtuozzo.com> Signed-off-by: Miklos Szeredi <mszeredi@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Right now when a new overlay inode is created, we initialize overlay
inode's ->i_mode from underlying inode ->i_mode but we retain only
file type bits (S_IFMT) and discard permission bits.
This patch changes it and retains permission bits too. This should allow
overlay to do permission checks on overlay inode itself in task context.
[SzM] It also fixes clearing suid/sgid bits on write.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com> Reported-by: Eryu Guan <eguan@redhat.com> Signed-off-by: Miklos Szeredi <mszeredi@redhat.com> Fixes: 4bacc9c9234c ("overlayfs: Make f_path always point to the overlay and f_inode to the underlay") Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Until now, our understanding for HW I/O coherency to work on the
Cortex-A9 based Marvell SoC was that only the PCIe regions should be
mapped strongly-ordered. However, we were still encountering some
deadlocks, especially when testing the CESA crypto engine. After
checking with the HW designers, it was concluded that all the MMIO
registers should be mapped as strongly ordered for the HW I/O coherency
mechanism to work properly.
This fixes some easy to reproduce deadlocks with the CESA crypto engine
driver (dmcrypt on a sufficiently large disk partition).
Tested-by: Terry Stockert <stockert@inkblotadmirer.me> Tested-by: Romain Perier <romain.perier@free-electrons.com> Cc: Terry Stockert <stockert@inkblotadmirer.me> Cc: Romain Perier <romain.perier@free-electrons.com> Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
When the support for the Marvell crypto engine was added in the Device
Tree of the various Armada 385 Device Tree files in commit d716f2e837ac6 ("ARM: mvebu: define crypto SRAM ranges for all armada-38x
boards"), a typo was made in the MBus window attributes for the Armada
385 Linksys board: 0x09/0x05 are used instead of 0x19/0x15. This commit
fixes this typo, which makes the CESA engines operational on Armada 385
Linksys boards.
Reported-by: Terry Stockert <stockert@inkblotadmirer.me> Cc: Terry Stockert <stockert@inkblotadmirer.me> Cc: Imre Kaloz <kaloz@openwrt.org> Cc: Boris Brezillon <boris.brezillon@free-electrons.com> Fixes: d716f2e837ac6 ("ARM: mvebu: define crypto SRAM ranges for all armada-38x boards") Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
projects / mirror_ubuntu-artful-kernel.git / log