The nl80211 attribute NL80211_ATTR_CSA_C_OFF_BEACON should be nested
inside NL80211_ATTR_CSA_IES, but commit ee4bc9e75811d2c0cb5f2a2fc5b5
("nl80211: enable IBSS support for channel switch announcements")
added a check in the outer message attributes.
Fix channel switch calls by removing the erroneus condition.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
[reword commit message] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Jouni Malinen [Tue, 22 Oct 2013 11:11:17 +0000 (14:11 +0300)]
mac80211_hwsim: Fix tracking of beaconing for multi-vif
mac80211_hwsim canceled beacon_timer on any vif changing from enabled
to disabled beaconing. This breaks cases where there are multiple
beaconing vifs and only one of them is removed. Fix this by tracking
beaconing status per vif and disable beacon_timer only if no active vif
remain with beaconing enabled.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Chun-Yeow Yeoh [Thu, 17 Oct 2013 22:55:18 +0000 (15:55 -0700)]
mac80211: process mesh channel switching using beacon
Trigger the mesh channel switching procedure if the mesh STA
happens to miss the CSA action frame but able to receive the
beacon containing the CSA and MCSP elements from its peer
mesh STAs.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@cozybit.com>
[fix locking in ieee80211_mesh_process_chnswitch()] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Chun-Yeow Yeoh [Thu, 17 Oct 2013 22:55:02 +0000 (15:55 -0700)]
{nl,cfg,mac}80211: implement mesh channel switch userspace API
Implement the required procedures for mesh channel switching as defined
in the IEEE Std 802.11-2012 section 10.9.8.4.3 and also handle the CSA
and MCSP elements as followed:
* Add the function for updating the beacon and probe response frames
with CSA and MCSP elements during the period of switching to the new
channel. Both CSA and MCSP elements must be included in beacon and
probe response frames until the intended channel switch time.
* The ifmsh->csa_settings is set to NULL and the CSA and MCSP elements
will then be removed from the beacon or probe response frames once the
new channel is switched to.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@cozybit.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Chun-Yeow Yeoh [Tue, 15 Oct 2013 02:08:28 +0000 (19:08 -0700)]
{nl,cfg,mac}80211: enable the triggering of CSA frame in mesh
Allow the triggering of CSA frame using mesh interface. The
rules are more or less same with IBSS, such as not allowed to
change between the band and channel width has to be same from
the previous mode. Also, move the ieee80211_send_action_csa
to a common space so that it can be re-used by mesh interface.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@cozybit.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Chun-Yeow Yeoh [Tue, 15 Oct 2013 02:08:27 +0000 (19:08 -0700)]
mac80211: process the CSA frame for mesh accordingly
Process the CSA frame according to the procedures define in IEEE Std
802.11-2012 section 10.9.8.4.3 as follow:
* The mesh channel switch parameters element (MCSP) must be availabe.
* If the MCSP's TTL is 1, drop the frame but still process the CSA.
* If the MCSP's precedence value is less than or equal to the current
precedence value, drop the frame and do not process the CSA.
* The CSA frame is forwarded after TTL is decremented by 1 and the
initiator field is set to 0. Transmit restrict field and others
are maintained as is.
* No beacon or probe response frame are handled here.
Also, introduce the debug message used for mesh CSA purpose.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@cozybit.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Felix Fietkau [Mon, 14 Oct 2013 16:01:00 +0000 (18:01 +0200)]
mac80211: add ieee80211_tx_prepare_skb() helper function
This can be used by a driver to prepare skbs for transmission, which were
obtained via functions such as ieee80211_probereq_get or
ieee80211_nullfunc_get.
This is useful for drivers that want to send those frames directly, but
need rate control information to be prepared first.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Marco Porsch [Tue, 15 Oct 2013 10:29:24 +0000 (12:29 +0200)]
mac80211: fixes for mesh powersave logic
This patch fixes errors in the mesh powersave logic which
cause that remote peers do not get peer power mode change
notifications and mesh peer service periods (MPSPs) got
stuck.
When closing a peer link, set the (now invalid) peer-specific
power mode to 'unknown'.
Avoid overhead when local power mode is unchanged.
Reliably clear MPSP flags on peering status update.
Avoid MPSP flags getting stuck by not requesting a further
MPSP ownership if we already are an MPSP owner.
Signed-off-by: Marco Porsch <marco@cozybit.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Seth Forshee [Tue, 15 Oct 2013 21:16:21 +0000 (16:16 -0500)]
mac80211: Remove check for offchannel state when waking netdev queues
6c17b77b67587b9f9e3070fb89fe98cef3187131 ensures that a device's
mac80211 queues will remain stopped while offchannel. Since the
vif can no longer be offchannel when the queues wake it's not
necessary to check for this before waking its netdev queues.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Heikki Krogerus [Wed, 16 Oct 2013 10:53:43 +0000 (13:53 +0300)]
net: rfkill: gpio: add ACPI support
Including ACPI ID for Broadcom GPS receiver BCM4752.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Acked-by: Rhyland Klein <rklein@nvidia.com> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Heikki Krogerus [Wed, 16 Oct 2013 10:53:42 +0000 (13:53 +0300)]
net: rfkill: gpio: prepare for DT and ACPI support
This will add the relevant values like the gpios and the
type in rfkill_gpio_platform_data to the rfkill_gpio_data
structure. It will allow those values to be easily picked
from DT and ACPI tables later.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Acked-by: Rhyland Klein <rklein@nvidia.com> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Heikki Krogerus [Wed, 16 Oct 2013 10:53:41 +0000 (13:53 +0300)]
net: rfkill: gpio: spinlock-safe GPIO access
This sets the direction of the gpio once when it's requested,
and uses the spinlock-safe gpio_set_state() to change the
state.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Acked-by: Rhyland Klein <rklein@nvidia.com> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Heikki Krogerus [Wed, 16 Oct 2013 10:53:40 +0000 (13:53 +0300)]
net: rfkill: gpio: clean up clock handling
Use a simple flag to see the state of the clock, and make
the clock available even without a name. Also, get rid of
HAVE_CLK dependency.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Acked-by: Rhyland Klein <rklein@nvidia.com> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Heikki Krogerus [Wed, 16 Oct 2013 10:53:39 +0000 (13:53 +0300)]
net: rfkill: gpio: convert to resource managed allocation
And remove now unneeded resource freeing.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Acked-by: Rhyland Klein <rklein@nvidia.com> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To use DFS in IBSS mode, userspace is required to react to radar events.
It can inform nl80211 that it is capable of doing so by adding a
NL80211_ATTR_HANDLE_DFS attribute when joining the IBSS.
This attribute is supplied to let the kernelspace know that the
userspace application can and will handle radar events, e.g. by
intiating channel switches to a valid channel. DFS channels may
only be used if this attribute is supplied and the driver supports
it. Driver support will be checked even if a channel without DFS
will be initially joined, as a DFS channel may be chosen later.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de> Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
[fix attribute name in commit message] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the driver requests to move to STATIC or DYNAMIC SMPS,
we send an action frame to each associated station and
reconfigure the channel context / driver.
Of course, non-MIMO stations are ignored.
The beacon isn't updated. The association response will
include the original capabilities. Stations that associate
while in non-OFF SMPS mode will get an action frame right
after association to inform them about our current state.
Note that we wait until the end of the EAPOL. Sending an
action frame before the EAPOL is finished can be an issue
for a few clients. Clients aren't likely to send EAPOL
frames in MIMO anyway.
When the SMPS configuration gets more permissive (e.g.
STATIC -> OFF), we don't wake up stations that are asleep
We remember that they don't know about the change and send
the action frame when they wake up.
When the SMPS configuration gets more restrictive (e.g.
OFF -> STATIC), we set the TIM bit for every sleeping STA.
uAPSD stations might send MIMO until they poll the action
frame, but this is for a short period of time.
In order to reconfigure the correct reg domain on
recovery, we have to save the current configuration
before clearing it (wl->reg_ch_conf_pending is
considered before configuring a new regdomain).
wlcore configures different dwell times according to number
of active interfaces (in order to prevent hurting VO during
scan).
However, determining active vif only according to
bss_conf->idle is not explicit enough, and might result
in non-started vifs being counted as started as well
(e.g. unassociated sta during sta).
Fix it by checking for explicit conditions according
to the vif type.
The FW panic log is read during recovery work.
It has to be stopped properly before reading. otherwise,
inconsistent data might be read which cause the driver
to freeze.
__wlcore_cmd_send has to work for the special case of
CMD_STOP_FWLOGGER, while in recovery, in order to stop
the fw log before it is read.
Ido Reis [Mon, 9 Sep 2013 09:24:36 +0000 (12:24 +0300)]
wlcore: fwlog dynamic mem_block control
number of fwlog mem_blocks can be configured using module param.
this is a fw debug feature: in case a large fw log data is busrted during
a short period of time, the memory get filled and data is lost.
this allows us to dynamicly set the fw log mem_block usage, although
configuring more mem_block for logger comes at the expense of TP.
Change interrogate command prototype to have command size
and returned buffer length.
This fixes the issue when command parameters are needed to
be passed to FW in addition to acx header as in the case with
get RSSI command, where role_id has to be passed.
Gustavo Padovan [Mon, 21 Oct 2013 20:22:26 +0000 (18:22 -0200)]
Bluetooth: Remove sk member from struct l2cap_chan
There is no access to chan->sk in L2CAP core now. This change marks the
end of the task of splitting L2CAP between Core and Socket, thus sk is now
gone from struct l2cap_chan.
Gustavo Padovan [Mon, 21 Oct 2013 20:22:25 +0000 (18:22 -0200)]
Bluetooth: Use bt_cb(skb)->chan to send raw data back
Instead of accessing skb->sk in L2CAP core we now compare the channel
a skb belongs to and not send it back if the channel is same. This change
removes another struct socket usage from L2CAP core.
Gustavo Padovan [Mon, 21 Oct 2013 16:21:41 +0000 (14:21 -0200)]
Bluetooth: Remove parent socket usage from l2cap_core.c
The parent socket is not used inside the L2CAP core anymore. We only lock
it to indirect access through the new_connection() callback. The hold of
the socket lock was moved to the new_connection() callback.
Inside L2CAP core the channel lock is now used in l2cap_le_conn_ready()
and l2cap_conn_ready() to protect the execution of these two functions
during the handling of new incoming connections.
This change remove the socket lock usage from L2CAP core while keeping
the code safe against race conditions.
Gustavo Padovan [Mon, 21 Oct 2013 16:21:40 +0000 (14:21 -0200)]
Bluetooth: Remove socket lock from l2cap_state_change()
This simplify and make safer the state change handling inside l2cap_core.c.
we got rid of __l2cap_state_change(). And l2cap_state_change() doesn't lock
the socket anymore, instead the socket is locked inside the ops callback for
state change in l2cap_sock.c.
It makes the code safer because in some we were using a unlocked version,
and now we are calls to l2cap_state_change(), when dealing with sockets, use
the locked version.
Gustavo Padovan [Mon, 21 Oct 2013 16:21:39 +0000 (14:21 -0200)]
Bluetooth: Hold socket in defer callback in L2CAP socket
In both places that we use the defer callback the socket lock is held for
a indirect sk access inside __l2cap_change_state() and chan->ops->defer(),
all the rest of the code between lock_sock() and release_sock() is
already protected by the channel lock and won't be affected by this
change.
We now use l2cap_change_state(), the locked version of the change state
function, and the defer callback does the locking itself now. This does
not affect other uses of the defer callback.
Gustavo Padovan [Mon, 21 Oct 2013 16:21:38 +0000 (14:21 -0200)]
Bluetooth: Do not access chan->sk directly
In the process of removing socket usage from L2CAP we now access the L2CAP
socket from the data member of struct l2cap_chan. For the L2CAP socket
user the data member points to the L2CAP socket.
Michal Kazior [Thu, 17 Oct 2013 18:21:11 +0000 (11:21 -0700)]
cfg80211: fix DFS channel recovery timeout
The timeout was not properly converted from msecs
to jiffies. As a result channel transition to
NL80211_DFS_USABLE was delayed depending on
CONFIG_HZ configuration, e.g. HZ=100 would delay
the NOP from 30 minutes to 300 minutes.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Mon, 21 Oct 2013 09:33:35 +0000 (11:33 +0200)]
cfg80211: fix scheduled scan pointer access
Since rdev->sched_scan_req is dereferenced outside the
lock protecting it, this might be done at the wrong
time, causing crashes. Move the dereference to where
it should be - inside the RTNL locked section.
Johan Hedberg [Sun, 20 Oct 2013 16:00:07 +0000 (19:00 +0300)]
Bluetooth: Update Set Discoverable to support LE
This patch updates the Set Discoverable management command to also be
applicable for LE. In particular this affects the advertising flags
where we can say "general discoverable" or "limited discoverable".
Since the device flags may not be up-to-date when the advertising data
is written this patch introduces a get_adv_discov_flags() helper
function which also looks at any pending mgmt commands (a pending
set_discoverable would be the exception when the flags are not yet
correct).
The patch also adds HCI_DISCOVERABLE flag clearing to the
mgmt_discoverable_timeout function, since the code was previously
relying on the mgmt_discoverable callback to handle this, which is only
called for the BR/EDR-only HCI_Write_Scan_Enable command.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Johan Hedberg [Sat, 19 Oct 2013 20:38:22 +0000 (23:38 +0300)]
Bluetooth: Move HCI_LIMITED_DISCOVERABLE changes to a general place
We'll soon be introducing also LE support for the Set Discoverable
management command, so move the HCI_LIMITED_DISCOVERABLE flag clearing
and setting out from the if-branch that is only used for a BR/EDR
specific HCI command.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Johan Hedberg [Sat, 19 Oct 2013 20:38:21 +0000 (23:38 +0300)]
Bluetooth: Fix sending write_scan_enable when BR/EDR is disabled
We should only send the HCI_Write_Scan_Enable command from
mgmt_set_powered_failed() when BR/EDR support is enabled. This is
particularly important when the discoverable setting is also tied to LE.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Johan Hedberg [Sat, 19 Oct 2013 20:38:19 +0000 (23:38 +0300)]
Bluetooth: Fix updating settings when there are no HCI commands to send
It is possible that the Set Connectable management command doesn't cause
any HCI commands to send (such as when BR/EDR is disabled). We can't
just send a response to user space in this case but must also update the
necessary device flags and settings. This patch fixes the issue by using
the recently introduced set_connectable_update_settings function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Johan Hedberg [Sat, 19 Oct 2013 20:38:18 +0000 (23:38 +0300)]
Bluetooth: Refactor set_connectable settings update to separate function
We will need to directly update the device flags and notify user space
of the new settings not just when we're powered off but also if it turns
out that there are no HCI commands to send (which can happen in
particular when BR/EDR is disabled). Since this is a considerable amount
of code, refactor it to a separate function so it can be reused for the
"no HCI commands to send" case.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Johan Hedberg [Sat, 19 Oct 2013 20:38:16 +0000 (23:38 +0300)]
Bluetooth: Check for flag instead of features in update_adv_data()
It's better to check for the device flag instead of device features so
that we avoid unnecessary HCI commands when the feature is supported but
disabled (i.e. the flag is unset).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Johan Hedberg [Sat, 19 Oct 2013 20:38:15 +0000 (23:38 +0300)]
Bluetooth: Check for flag instead of features in update_scan_rsp_data()
It's better to check for the device flag instead of device features so
that we avoid unnecessary HCI commands when the feature is supported but
disabled (i.e. the flag is unset).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Marcel Holtmann [Sat, 19 Oct 2013 16:31:59 +0000 (09:31 -0700)]
Bluetooth: Fix UUID values in debugfs file
The uuid entry struct is used for the UUID byte stream. That is
actually the wrong value. The correct value is uuid->uuid.
Besides fixing this up, use the %pUb modifier to print the UUID
string. However since the UUID is stored in big endian with
reversed byte order, change the byte order before printing.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Marcel Holtmann [Sat, 19 Oct 2013 14:09:12 +0000 (07:09 -0700)]
Bluetooth: Add support for setting DUT mode
The Device Under Test (DUT) mode is useful for doing certification
testing and so expose this as debugfs option.
This mode is actually special since you can only enter it. Restoring
normal operation means that a HCI Reset is required. The current mode
value gets tracked as a new device flag and when disabling it, the
correct command to reset the controller is sent.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Marcel Holtmann [Fri, 18 Oct 2013 23:38:10 +0000 (16:38 -0700)]
Bluetooth: Expose debugfs entry read/write own address type
For some testing it is important to know the current own addres type,
but also be able to change it. The change is lost over powery cycles
and only intended for debugging.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Marcel Holtmann [Fri, 18 Oct 2013 23:38:09 +0000 (16:38 -0700)]
Bluetooth: Select the own address type during initial setup phase
The own address type is based on the fact if the controller has
a public address or not. This means that this detail can be just
configured once during setup phase.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Marcel Holtmann [Fri, 18 Oct 2013 19:04:50 +0000 (12:04 -0700)]
Bluetooth: Store local version information only during setup phase
The local version information from the controller can not change
since they are static. So store them only once during setup
phase and not bother overwriting them every time this command
gets executed.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Marcel Holtmann [Fri, 18 Oct 2013 19:04:49 +0000 (12:04 -0700)]
Bluetooth: Move manufacturer, hci_ver and hci_rev into hci_core.c
Move the debugfs entries for manufacturer, hci_ver and hci_rev into
hci_core.c and use the new helpers for static entries that will not
change at runtime. Once passed the setup procedure, they will stay
fixed.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Marcel Holtmann [Fri, 18 Oct 2013 19:04:47 +0000 (12:04 -0700)]
Bluetooth: Add workaround for buggy max_page features page value
Some controllers list the max_page value from the extended features
response as 0 when SSP has not yet been enabled. To workaround this
issue, force the max_page value to 1 when SSP support has been
detected.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Gabor Juhos [Thu, 17 Oct 2013 07:42:33 +0000 (09:42 +0200)]
rt2x00: rt2800pci: use separate hwcrypt_disabled callback for SoC devices
The 'rt2800pci_hwcrypt_disabled' function is the
only PCI specific callback which is used by the
SoC driver. Create a clone of that to get rid of
the dependency.
Even though the two functions are using the same
variable, but the SoC specific code will be moved
into a separate module which will have its own
'modparam_nohwcrypt' variable.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Thu, 17 Oct 2013 07:42:31 +0000 (09:42 +0200)]
rt2x00: rt2800pci: split rt2800pci_enable_radio function
The function is called for PCI and SoC devices
however the MCU related part of the function
has no effect on SoC devices. Move the common
part of the function into a separate helper and
use that for the SoC devices.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Thu, 17 Oct 2013 07:42:30 +0000 (09:42 +0200)]
rt2x00: rt2800pci: rename rt2800pci_disable_radio function
The function contain code for SoC devices only.
Rename the function to 'rt2800soc_disable_radio'
and move it to the SoC specific section. Use
the renamed function in the SoC specific code
only and remove the 'if rt2x00_is_soc(rt2x00dev)'
condition from the function body.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Thu, 17 Oct 2013 07:42:29 +0000 (09:42 +0200)]
rt2x00: rt2800pci: use separate set_state callback for SoC devices
The 'rt2800pci_set_state' function uses MCU commands
to set the device state, however these have no effect
on SoC devices. Use a different set_state callback
which does not use the MCU fcuntions.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Thu, 17 Oct 2013 07:42:27 +0000 (09:42 +0200)]
rt2x00: rt2800pci: use separate read_eeprom callback for SoC devices
Rename the 'rt2800pci_read_eeprom_soc function' to
'rt2800soc_read_eeprom' and use that directly in the
SoC specific 'rt2800_ops' structure. Also move the
'rt2800pci_eeprom_read' function into an 'ifdef PCI'
section and remove the 'rt2800pci_read_eeprom_soc'
call from that.
Additionally, remove the dummy inline eeprom functions.
Those are not used anymore.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Thu, 17 Oct 2013 07:42:24 +0000 (09:42 +0200)]
rt2x00: rt2800pci: use rt2800mmio prefix for initialization functions
The functions are used for devices with memory
mapped I/O and contain no PCI specific code at
all. Use rt2800mmio prefix instead of rt2800pci
in the function names to reflect that.
The patch contains no functional changes.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Thu, 17 Oct 2013 07:42:23 +0000 (09:42 +0200)]
rt2x00: rt2800pci: move queue functions to the rt2800mmio module
Move the functions into a separate module, in order
to make those usable from other modules. Also move
the queue register offset macros from rt2800pci.h
into rt2800mmio.h.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Thu, 17 Oct 2013 07:42:22 +0000 (09:42 +0200)]
rt2x00: rt2800pci: use rt2800mmio prefix for queue functions
The functions are used for devices with memory
mapped I/O and contain no PCI specific code at
all. Use rt2800mmio prefix instead of rt2800pci
in the function names to reflect that.
The patch contains no functional changes.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Thu, 17 Oct 2013 07:42:20 +0000 (09:42 +0200)]
rt2x00: rt2800pci: use rt2800mmio prefix for interrupt functions
The functions are used for devices with memory
mapped I/O and contain no PCI specific code at
all. Use rt2800mmio prefix instead of rt2800pci
in the function names to reflect that.
The patch contains no functional changes.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Thu, 17 Oct 2013 07:42:19 +0000 (09:42 +0200)]
rt2x00: rt2800pci: move RX control handler functions to the rt2800mmio module
Move the functions into a separate module, in order
to make those usable from other modules. Also move
the RX descriptor related defines from rt2800pci.h
into rt2800mmio.h
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Thu, 17 Oct 2013 07:42:18 +0000 (09:42 +0200)]
rt2x00: rt2800pci: use rt2800mmio prefix for RX control handler functions
The functions are used for devices with memory
mapped I/O and contain no PCI specific code at
all. Use rt2800mmio prefix instead of rt2800pci
in the function names to reflect that.
The patch contains no functional changes.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Thu, 17 Oct 2013 07:42:17 +0000 (09:42 +0200)]
rt2x00: rt2800pci: move TX descriptor functions to the rt2800mmio module
Move the functions into a separate module, in order
to make those usable from other modules. Also move
the TX descriptor related defines from rt2800pci.h
into rt2800mmio.h.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Thu, 17 Oct 2013 07:42:16 +0000 (09:42 +0200)]
rt2x00: rt2800pci: use rt2800mmio prefix for TX descriptor functions
The functions are used for devices with memory
mapped I/O and contain no PCI specific code at
all. Use rt2800mmio prefix instead of rt2800pci
in the function names to reflect that.
The patch contains no functional changes.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>