Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
(cherry picked from commit 169a88c1ee19b0734c9703d51a6d8ebe538f5bc3) Signed-off-by: Shrirang Bagul <shrirang.bagul@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Linus Walleij [Thu, 24 Mar 2016 13:18:04 +0000 (14:18 +0100)]
iio: st_sensors: read each channel individually
BugLink: https://bugs.launchpad.net/bugs/1676356
The current buffer read code tries to optimize reads from the
sensor data registers by issuing a single read operation across
all the indata registers.
This doesn't work: when the LIS331DL accelerometer sensor is
configured to open drain, active low interrupt mode, this will
just clear the XDA (X-axis data available) bit in the STATUS_REG
register (0x27), while YDA, ZDA and even ZYXDA remain set to 1,
and the internal logic of the sensor holds the DRDY (INT1) line
asserted (the value of the status register is 0xee).
If we instead issue one read operation per enabled channel
(X, Y, Z) things start working and we can use open drain and
active low interrupts.
Note that a backported patch fixing this issue will be heading
via the fixes branch but changes in this file already in staging-next
will make that patch 'look' rather different. The code in here
is the correct one when that clash hits.
Cc: Giuseppe Barba <giuseppe.barba@st.com> Cc: Denis Ciocca <denis.ciocca@st.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
(cherry picked from commit 6436db37b4a5da1ae1f381e4791e17e2236fd276) Signed-off-by: Shrirang Bagul <shrirang.bagul@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Linus Walleij [Thu, 24 Mar 2016 13:18:03 +0000 (14:18 +0100)]
iio: st_sensors: simplify buffer address handling
BugLink: https://bugs.launchpad.net/bugs/1676356
The driver goes to some length to dynamically allocate an array
to hold the channel addresses. However no ST sensor has more than
three channels (x, y, z at most). Instead of kmalloc():ing and
kfree():in the address array, just use a fixed array of three
elements.
Cc: Giuseppe Barba <giuseppe.barba@st.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Denis Ciocca <denis.ciocca@st.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
(cherry picked from commit e6e45420f41fc613569e8bb6d15e0472dc0ea1ab) Signed-off-by: Shrirang Bagul <shrirang.bagul@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Signed-off-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
(cherry picked from commit f47dff323088462e7b0ac52d1ba41ce953a5ce20) Signed-off-by: Shrirang Bagul <shrirang.bagul@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Shashank Sharma [Tue, 28 Mar 2017 07:42:18 +0000 (15:42 +0800)]
drm/i915: Add lspcon resume function
BugLink: https://bugs.launchpad.net/bugs/1676747
As per the software design, we are driving lspcon in
PCON mode. But while resuming from suspend, lspcon can go
in LS mode (which is its default operating mode on power on)
This patch adds a resume function for lspcon, which makes sure
its operating in PCON mode, post resume.
V2: Address review comments from Imre
- move lspcon_resume call to encoder->reset()
- use early returns
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1476455212-27893-6-git-send-email-shashank.sharma@intel.com
(cherry picked from commit 910530c0630541aa5d2f20ea15f3108bfe2c1693) Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Acked-by: Tim Gardner <tim.gardner@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Shashank Sharma [Tue, 28 Mar 2017 07:42:17 +0000 (15:42 +0800)]
drm/i915: Enable lspcon initialization
BugLink: https://bugs.launchpad.net/bugs/1676747
This patch adds initialization code for lspcon.
What we are doing here is:
- Check if lspcon is configured in VBT for this port
- If lspcon is configured, initialize it and configure it
as DP port.
V2: Addressed Ville's review comments:
- Not adding AVI IF functions for LSPCON display now.
This part will be added once the dig_port level AVI-IF series
gets merged.
V3: Rebase
V4: Rebase
V5: Rebase
V6: Rebase
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com> Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1476455212-27893-5-git-send-email-shashank.sharma@intel.com
(cherry picked from commit ff66212415e3240cb4f79a09b00a03dd56d48b16) Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Acked-by: Tim Gardner <tim.gardner@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Shashank Sharma [Tue, 28 Mar 2017 07:42:16 +0000 (15:42 +0800)]
drm/i915: Parse VBT data for lspcon
BugLink: https://bugs.launchpad.net/bugs/1676747
Many GEN9 boards come with on-board lspcon cards.
Fot these boards, VBT configuration should properly point out
if a particular port contains lspcon device, so that driver can
initialize it properly.
This patch adds a utility function, which checks the VBT flag
for lspcon bit, and tells us if a port is configured to have a
lspcon device or not.
V2: Fixed review comments from Ville
- Do not forget PORT_D while checking lspcon for GEN9
V3: Addressed review comments from Rodrigo
- Create a HAS_LSPCON() macro for better use case handling.
- Do not dump warnings for non-gen-9 platforms, it will be noise.
V4: Rebase
V5: Rebase
V6: Pass dev_priv to HAS_LSPCON() macro
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com> Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1476455212-27893-4-git-send-email-shashank.sharma@intel.com
(cherry picked from commit 6389dd83768485a251dc0c5252dbc9a96f86ca53) Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Acked-by: Tim Gardner <tim.gardner@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Shashank Sharma [Tue, 28 Mar 2017 07:42:15 +0000 (15:42 +0800)]
drm/i915: Add lspcon support for I915 driver
BugLink: https://bugs.launchpad.net/bugs/1676747
This patch adds a new file, to accommodate lspcon support
for I915 driver. These functions probe, detect, initialize
and configure an on-board lspcon device during the driver
init time.
Also, this patch adds a small structure for lspcon device,
which will provide the runtime status of the device.
V2: addressed ville's review comments
- Clean the leftover macros from previous patch set
V3: Rebase
V4: addressed ville's review comments
- make internal functions static
- remove lspcon_detect_identifier, make it inline with lspcon_probe
- remove is_lspcon_active function
- remove force check while setting a lspcon mode
V5: Rebase
V6: Pass dev_priv to IS_GEN9 check
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com> Signed-off-by: Akashdeep Sharma <akashdeep.sharma@intel.com> Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1476455212-27893-3-git-send-email-shashank.sharma@intel.com
(cherry picked from commit dbe9e61b8e4306df24b3e8370a62f7954a81ff5d) Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Acked-by: Tim Gardner <tim.gardner@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Shashank Sharma [Tue, 28 Mar 2017 07:42:14 +0000 (15:42 +0800)]
drm: Helper for lspcon in drm_dp_dual_mode
BugLink: https://bugs.launchpad.net/bugs/1676747
This patch adds lspcon support in dp_dual_mode helper.
lspcon is essentially a dp->hdmi dongle with dual personality.
LS mode: It works as a passive dongle, by level shifting DP++
signals to HDMI signals, in LS mode.
PCON mode: It works as a protocol converter active dongle
in pcon mode, by converting DP++ outputs to HDMI 2.0 outputs.
This patch adds support for lspcon detection and mode set
switch operations, as a dp dual mode dongle.
v2: Addressed review comments from Ville
- add adaptor id for lspcon devices (0x08), use it to identify lspcon
- change function names
old: drm_lspcon_get_current_mode/drm_lspcon_change_mode
new: drm_lspcon_get_mode/drm_lspcon_set_mode
- change drm_lspcon_get_mode type to int, to match
drm_dp_dual_mode_get_tmds_output
- change 'err' to 'ret' to match the rest of the functions
- remove pointless typecasting during call to dual_mode_read
- fix the but while setting value of data, while writing lspcon mode
- fix indentation
- change mdelay(10) -> msleep(10)
- return ETIMEDOUT instead of EFAULT, when lspcon mode change times out
- Add an empty line to separate std regs macros and lspcon regs macros
Indent bit definition
v3: Addressed review comments from Rodrigo
- change macro name from DP_DUAL_MODE_TYPE_LSPCON to
DP_DUAL_MODE_TYPE_HAS_DPCD for better readability
- change macro name from DP_DUAL_MODE_LSPCON_MODE_PCON to
DP_DUAL_MODE_LSPCON_MODE_PCON for better readability
- add comment for MCA specific offsets like 0x40 and 0x41
- remove DP_DUAL_MODE_REV_TYPE2 check while checking lspcon adapter id
v4: Addressed review comments from Ville
- Fixed indentation at few places
- s/current_mode/mode
- s/reqd_mode/mode
- remove unnecessary void* cast
- remove drm_edid.h from includes
- Add a comment for _HAS_DPCD
- Fix enum description, for lspcon_mode.
v5: Rebase
v6: Rebase
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com> Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Acked-by: Dave Airlie <airlied@gmail.com> Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1476720277-16298-1-git-send-email-shashank.sharma@intel.com
(cherry picked from commit 056996b95686324fdc00e72f8cea01be2356ef62) Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Acked-by: Tim Gardner <tim.gardner@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Colin Ian King [Mon, 27 Mar 2017 11:30:34 +0000 (12:30 +0100)]
ext4: lock the xattr block before checksuming it
BugLink: https://bugs.launchpad.net/bugs/1658633
We must lock the xattr block before calculating or verifying the
checksum in order to avoid spurious checksum failures.
Reported-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Cc: stable@vger.kernel.org
(backport of upstream commit dac7a4b4b1f664934e8b713f529b629f67db313c) Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: Tim Gardner <tim.gardner@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Signed-off-by: Shrirang Bagul <shrirang.bagul@canonical.com> Acked-by: Tim Gardner <tim.gardner@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/1674390
If the processor supports HWP, enable it by default without checking
for the cpu model. This will allow to enable HWP in all supported
processors without driver change.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
(cherry picked from commit 7791e4aa59ad724e0b4c8b4dea547a5735108972) Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Acked-by: Tim Gardner <tim.gardner@canonical.com> Acked-By: Robert Hooker <robert.hooker@canonical.com> Acked-by: Colin King <colin.king@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Florian Westphal [Fri, 17 Mar 2017 14:36:12 +0000 (10:36 -0400)]
bridge: drop netfilter fake rtable unconditionally
BugLink: https://bugs.launchpad.net/bugs/1672470
Andreas reports kernel oops during rmmod of the br_netfilter module.
Hannes debugged the oops down to a NULL rt6info->rt6i_indev.
Problem is that br_netfilter has the nasty concept of adding a fake
rtable to skb->dst; this happens in a br_netfilter prerouting hook.
A second hook (in bridge LOCAL_IN) is supposed to remove these again
before the skb is handed up the stack.
However, on module unload hooks get unregistered which means an
skb could traverse the prerouting hook that attaches the fake_rtable,
while the 'fake rtable remove' hook gets removed from the hooklist
immediately after.
Fixes: 34666d467cbf1e2e3c7 ("netfilter: bridge: move br_netfilter out of the core") Reported-by: Andreas Karis <akaris@redhat.com> Debugged-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: Florian Westphal <fw@strlen.de> Acked-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net>
(cherry-picked from upstream commit a13b2082ece95247779b9995c4e91b4246bed023) Signed-off-by: Dan Streetman <dan.streetman@canonical.com> Acked-by: Tim Gardner <tim.gardner@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Stefan Bader [Fri, 17 Mar 2017 09:44:55 +0000 (10:44 +0100)]
UBUNTU: d-i: Also add dm-queue-length to multipath modules
This should be the last one right now. We already added the
dm-service-time alternate load balancer. But some setups may
want the slightly different approach dm-queue-length offers.
BugLink: https://bugs.launchpad.net/bugs/1673350 Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Colin King <colin.king@canonical.com> Acked-by: Tim Gardner <tim.gardner@canonical.com> Acked-by: Seth Forshee <seth.forshee@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
BugLink: https://launchpad.net/bugs/1483101
Some btbcm devices require more time to complete its reset process.
They won't reply any hci command until reset is done.
[ 17.218554] Bluetooth: hci0 command 0x1001 tx timeout
[ 25.214999] Bluetooth: hci0: BCM: Reading local version info failed (-110)
Signed-off-by: Wen-chien Jesse Sung <jesse.sung@canonical.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
(cherry picked from commit 3af3a594e111474fab03d872f41760e10d4c17c4) Signed-off-by: Wen-chien Jesse Sung <jesse.sung@canonical.com> Acked-by: Seth Forshee <seth.forshee@canonical.com> Acked-by: Tim Gardner <tim.gardner@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Dave Ertman [Tue, 14 Mar 2017 14:24:54 +0000 (09:24 -0500)]
i40e: check for and deal with non-contiguous TCs
BugLink: http://bugs.launchpad.net/bugs/1672550
The i40e driver was causing a kernel panic when
non-contiguous Traffic Classes, or Traffic Classes not
starting with TC0, were configured on a link partner switch.
i40e does not support non-contiguous TCs.
To fix this, the patch changes the logic when determining
the total number of TCs enabled. Before, this would use the
highest TC number enabled and assume that all TCs below it were
also enabled. Now, we create a bitmask of enabled TCs and scan
it to determine not only the number of TCs, but also if the set
of enabled TCs starts at zero and is contiguous. If not, then
DCB is disabled by only returning one TC.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
(cherry picked from commit fbfe12c64f9650aa22f434dd9dd22df7ddf63221) Signed-off-by: Seth Forshee <seth.forshee@canonical.com> Acked-by: Tim Gardner <tim.gardner@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Sachin Prabhu [Thu, 23 Mar 2017 16:55:40 +0000 (10:55 -0600)]
Call echo service immediately after socket reconnect
BugLink: http://bugs.launchpad.net/bugs/1669941
Commit 4fcd1813e640 ("Fix reconnect to not defer smb3 session reconnect
long after socket reconnect") changes the behaviour of the SMB2 echo
service and causes it to renegotiate after a socket reconnect. However
under default settings, the echo service could take up to 120 seconds to
be scheduled.
The patch forces the echo service to be called immediately resulting a
negotiate call being made immediately on reconnect.
Signed-off-by: Sachin Prabhu <sprabhu@redhat.com> Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Steve French <smfrench@gmail.com>
(back ported from commit b8c600120fc87d53642476f48c8055b38d6e14c7) Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Conflicts:
fs/cifs/connect.c Acked-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
James Smart [Tue, 7 Mar 2017 16:50:49 +0000 (09:50 -0700)]
scsi: lpfc: Add missing memory barrier
BugLink: http://bugs.launchpad.net/bugs/1670490
On loosely ordered memory systems (PPC for example), the WQE elements
were being updated in memory, but not necessarily flushed before the
separate doorbell was written to hw which would cause hw to dma the
WQE element. Thus, the hardware occasionally received partially
updated WQE data.
Add the memory barrier after updating the WQE memory.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit 6b3b3bdb83b4ad51252d21bb13596db879e51850) Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Acked-by: Seth Forshee <seth.forshee@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com> Signed-off-by: Brad Figg <brad.figg@canonical.com>
Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
(cherry picked from commit 3ce093d4de753d6c92cc09366e29d0618a62f542) Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Acked-by: Tim Gardner <tim.gardner@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com> Signed-off-by: Brad Figg <brad.figg@canonical.com>
BugLink: http://bugs.launchpad.net/bugs/1670518
hv_do_hypercall() assumes that we pass a segment from a physically
contiguous buffer. A buffer allocated on the stack may not work if
CONFIG_VMAP_STACK=y is set.
Use kmalloc() to allocate this buffer.
Reported-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: Long Li <longli@microsoft.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: K. Y. Srinivasan <kys@microsoft.com>
(cherry picked from commit 0de8ce3ee8e38cc66683438f715c79a2cc69539e) Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Acked-by: Marcelo Cerri <marcelo.cerri@canonical.com> Acked-by: Joseph Salisbury <joseph.salisbury@canonical.com> Signed-off-by: Brad Figg <brad.figg@canonical.com>
Dexuan Cui [Tue, 7 Mar 2017 17:35:24 +0000 (10:35 -0700)]
PCI: hv: Delete the device earlier from hbus->children for hot-remove
BugLink: http://bugs.launchpad.net/bugs/1670518
After we send a PCI_EJECTION_COMPLETE message to the host, the host will
immediately send us a PCI_BUS_RELATIONS message with
relations->device_count == 0, so pci_devices_present_work(), running on
another thread, can find the being-ejected device, mark the
hpdev->reported_missing to true, and run list_move_tail()/list_del() for
the device -- this races hv_eject_device_work() -> list_del().
Move the list_del() in hv_eject_device_work() to an earlier place, i.e.,
before we send PCI_EJECTION_COMPLETE, so later the
pci_devices_present_work() can't see the device.
Signed-off-by: Dexuan Cui <decui@microsoft.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Jake Oshins <jakeo@microsoft.com> Acked-by: K. Y. Srinivasan <kys@microsoft.com> CC: Haiyang Zhang <haiyangz@microsoft.com> CC: Vitaly Kuznetsov <vkuznets@redhat.com>
(cherry picked from commit e74d2ebdda33b3bdd1826b5b92e9aa45bdf92bb3) Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Acked-by: Marcelo Cerri <marcelo.cerri@canonical.com> Acked-by: Joseph Salisbury <joseph.salisbury@canonical.com> Signed-off-by: Brad Figg <brad.figg@canonical.com>
Dexuan Cui [Tue, 7 Mar 2017 17:35:23 +0000 (10:35 -0700)]
PCI: hv: Fix hv_pci_remove() for hot-remove
BugLink: http://bugs.launchpad.net/bugs/1670518
1. We don't really need such a big on-stack buffer when sending the
teardown_packet: vmbus_sendpacket() here only uses sizeof(struct
pci_message).
2. In the hot-remove case (PCI_EJECT), after we send PCI_EJECTION_COMPLETE
to the host, the host will send a RESCIND_CHANNEL message to us and the
host won't access the per-channel ringbuffer any longer, so we needn't send
PCI_RESOURCES_RELEASED/PCI_BUS_D0EXIT to the host, and we shouldn't expect
the host's completion message of PCI_BUS_D0EXIT, which will never come.
3. We should send PCI_BUS_D0EXIT after hv_send_resources_released().
Signed-off-by: Dexuan Cui <decui@microsoft.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Jake Oshins <jakeo@microsoft.com> Acked-by: K. Y. Srinivasan <kys@microsoft.com> CC: Haiyang Zhang <haiyangz@microsoft.com> CC: Vitaly Kuznetsov <vkuznets@redhat.com>
(cherry picked from commit 17978524a636d007e6b929304ae3eb5ea0371019) Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Acked-by: Marcelo Cerri <marcelo.cerri@canonical.com> Acked-by: Joseph Salisbury <joseph.salisbury@canonical.com> Signed-off-by: Brad Figg <brad.figg@canonical.com>
BugLink: http://bugs.launchpad.net/bugs/1674292 Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
The problem is that when the kernel tries to truncate an inode in
ext4_truncate(), it tries to clear any on-disk data beyond i_size.
Without the encryption key, it can't do that, and so it triggers a
BUG.
E2fsck does *not* provide this service, and in practice most file
systems have their orphan list processed by e2fsck, so to avoid
crashing, this patch skips this step if we don't have access to the
encryption key (which is the case when processing the orphan list; in
all other cases, we will have the encryption key, or the kernel
wouldn't have allowed the file to be opened).
An open question is whether the fact that e2fsck isn't clearing the
bytes beyond i_size causing problems --- and if we've lived with it
not doing it for so long, can we drop this from the kernel replay of
the orphan list in all cases (not just when we don't have the key for
encrypted inodes).
Commit df2cb6daa4 ("block: Avoid deadlocks with bio allocation by
stacking drivers") created a workqueue for every bio set and code
in bio_alloc_bioset() that tries to resolve some low-memory deadlocks
by redirecting bios queued on current->bio_list to the workqueue if the
system is low on memory. However other deadlocks (see below **) may
happen, without any low memory condition, because generic_make_request
is queuing bios to current->bio_list (rather than submitting them).
** the related dm-snapshot deadlock is detailed here:
https://www.redhat.com/archives/dm-devel/2016-July/msg00065.html
Fix this deadlock by redirecting any bios on current->bio_list to the
bio_set's rescue workqueue on every schedule() call. Consequently,
when the process blocks on a mutex, the bios queued on
current->bio_list are dispatched to independent workqueus and they can
complete without waiting for the mutex to be available.
The structure blk_plug contains an entry cb_list and this list can contain
arbitrary callback functions that are called when the process blocks.
To implement this fix DM (ab)uses the onstack plug's cb_list interface
to get its flush_current_bio_list() called at schedule() time.
This fixes the snapshot deadlock - if the map method blocks,
flush_current_bio_list() will be called and it redirects bios waiting
on current->bio_list to appropriate workqueues.
Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=1267650
Depends-on: df2cb6daa4 ("block: Avoid deadlocks with bio allocation by stacking drivers") Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
The interleave-set cookie is a sum that sanity checks the composition of
an interleave set has not changed from when the namespace was initially
created. The checksum is calculated by sorting the DIMMs by their
location in the interleave-set. The comparison for the sort must be
64-bit wide, not byte-by-byte as performed by memcmp() in the broken
case.
Fix the implementation to accept correct cookie values in addition to
the Linux "memcmp" order cookies, but only allow correct cookies to be
generated going forward. It does mean that namespaces created by
third-party-tooling, or created by newer kernels with this fix, will not
validate on older kernels. However, there are a couple mitigating
conditions:
1/ platforms with namespace-label capable NVDIMMs are not widely
available.
2/ interleave-sets with a single-dimm are by definition not affected
(nothing to sort). This covers the QEMU-KVM NVDIMM emulation case.
The cookie stored in the namespace label will be fixed by any write the
namespace label, the most straightforward way to achieve this is to
write to the "alt_name" attribute of a namespace in sysfs.
Fixes: eaf961536e16 ("libnvdimm, nfit: add interleave-set state-tracking infrastructure") Reported-by: Nicholas Moulin <nicholas.w.moulin@linux.intel.com> Tested-by: Nicholas Moulin <nicholas.w.moulin@linux.intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
In binutils/libbfd (bfd/elf.c) it is enforced that all s390 specific ELF
notes like e.g. NT_S390_PREFIX or NT_S390_CTRS have "LINUX" specified
as note name. Otherwise the notes are ignored.
For /proc/vmcore we currently use "CORE" for these notes.
Up to now this has not been a real problem because the dump analysis tool
"crash" does not check the note name. But it will break all programs that
use libbfd for processing ELF notes.
So fix this and use "LINUX" for all s390 specific notes to comply with
libbfd.
Reported-by: Philipp Rudo <prudo@linux.vnet.ibm.com> Reviewed-by: Philipp Rudo <prudo@linux.vnet.ibm.com> Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
While we can technically not run huge page guests right now, we can
setup a guest with huge pages. Trying to migrate it will trigger a
VM_BUG_ON and, if the kernel is not configured to panic on a BUG, it
will happily try to work on non-existing page table entries.
With this patch, we always return "dirty" if we encounter a large page
when migrating. This at least fixes the immediate problem until we
have proper handling for both kind of pages.
Fixes: 15f36eb ("KVM: s390: Add proper dirty bitmap support to S390 kvm.") Cc: <stable@vger.kernel.org> # 3.16+ Signed-off-by: Janosch Frank <frankja@linux.vnet.ibm.com> Acked-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Fix a smatch warning:
drivers/scsi/mvsas/mv_sas.c:740 mvs_task_prep() warn: curly braces intended?
The code is correct, the indention is misleading. When the device is not
ready we want to return SAS_PHY_DOWN. But current indentation makes it
look like we only do so in the else branch of if (mvi_dev).
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Add missing sanity check to the bulk-in completion handler to avoid an
integer underflow that can be triggered by a malicious device.
This avoids leaking 128 kB of memory content from after the URB transfer
buffer to user space.
Fixes: 8c209e6782ca ("USB: make actual_length in struct urb field u32") Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Fix a NULL-pointer dereference in the interrupt callback should a
malicious device send data containing a bad port number by adding the
missing sanity check.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Make sure to verify that we have the required interrupt-out endpoint for
IOWarrior56 devices to avoid dereferencing a NULL-pointer in write
should a malicious device lack such an endpoint.
Fixes: 946b960d13c1 ("USB: add driver for iowarrior devices.") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Make sure to check for the required interrupt-in endpoint to avoid
dereferencing a NULL-pointer should a malicious device lack such an
endpoint.
Note that a fairly recent change purported to fix this issue, but added
an insufficient test on the number of endpoints only, a test which can
now be removed.
Fixes: 4ec0ef3a8212 ("USB: iowarrior: fix oops with malicious USB descriptors") Fixes: 946b960d13c1 ("USB: add driver for iowarrior devices.") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
This driver needlessly took another reference to the tty on open, a
reference which was then never released on close. This lead to not just
a leak of the tty, but also a driver reference leak that prevented the
driver from being unloaded after a port had once been opened.
Fixes: 4a90f09b20f4 ("tty: usb-serial krefs") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Upstream commit 98d74f9ceaef ("xhci: fix 10 second timeout on removal of
PCI hotpluggable xhci controllers") fixes a problem with hot pluggable PCI
xhci controllers which can result in excessive timeouts, to the point where
the system reports a deadlock.
The same problem is seen with hot pluggable xhci controllers using the
xhci-plat driver, such as the driver used for Type-C ports on rk3399.
Similar to hot-pluggable PCI controllers, the driver for this chip
removes the xhci controller from the system when the Type-C cable is
disconnected.
The solution for PCI devices works just as well for non-PCI devices
and avoids the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
According to xHCI spec, HCIVERSION containing a BCD encoding
of the xHCI specification revision number, 0100h corresponds
to xHCI version 1.0. Change "100" as "0x100".
Cc: Lu Baolu <baolu.lu@linux.intel.com> Fixes: 04abb6de2825 ("xhci: Read and parse new xhci 1.1 capability register") Signed-off-by: Peter Chen <peter.chen@nxp.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
If we're dealing with SuperSpeed endpoints, we need
to make sure to pass along the companion descriptor
and initialize fields needed by the Gadget
API. Eventually, f_fs.c should be converted to use
config_ep_by_speed() like all other functions,
though.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Some gadget drivers are bad, bad boys. We notice
that ADB was passing bad Burst Size which caused top
bits of param0 to be overwritten which confused DWC3
when running this command.
In order to avoid future issues, we're going to make
sure values passed by macros are always safe for the
controller. Note that ADB still needs a fix to *not*
pass bad values.
Reported-by: Mohamed Abbas <mohamed.abbas@intel.com> Sugested-by: Adam Andruszak <adam.andruszak@intel.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
When the user does device unbind and rebind test, the kernel will
show below dump due to usb_gadget memory region is dirty after unbind.
Clear usb_gadget region for every new probe.
emulate_step() uses a number of underlying kernel functions that were
initially not enabled for LE. This has been rectified since. So, fix
emulate_step() for LE for the corresponding instructions.
Reported-by: Anton Blanchard <anton@samba.org> Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
There are several trace include files that define TRACE_INCLUDE_FILE.
Include several of them in the same .c file (as I currently have in
some code I am working on), and the compile will blow up with a
"warning: "TRACE_INCLUDE_FILE" redefined #define TRACE_INCLUDE_FILE syscalls"
Every other include file in include/trace/events/ avoids that issue
by having a #undef TRACE_INCLUDE_FILE before the #define; syscalls.h
should have one, too.
Link: http://lkml.kernel.org/r/20160928225554.13bd7ac6@annuminas.surriel.com Fixes: b8007ef74222 ("tracing: Separate raw syscall from syscall tracer") Signed-off-by: Rik van Riel <riel@redhat.com> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
A couple of netlogic assembly files define CP0_EBASE to $15, the same as
CP0_PRID in mipsregs.h, and use it for accessing both CP0_PRId and
CP0_EBase registers. However commit 609cf6f2291a ("MIPS: CPS: Early
debug using an ns16550-compatible UART") added a different definition of
CP0_EBASE to mipsregs.h, which included a register select of 1. This
causes harmless build warnings like the following:
arch/mips/netlogic/common/reset.S:53:0: warning: "CP0_EBASE" redefined
#define CP0_EBASE $15
^
In file included from arch/mips/netlogic/common/reset.S:41:0:
./arch/mips/include/asm/mipsregs.h:63:0: note: this is the location of the previous definition
#define CP0_EBASE $15, 1
^
Update the code to use the definitions from mipsregs.h for accessing
both registers.
Fixes: 609cf6f2291a ("MIPS: CPS: Early debug using an ns16550-compatible UART") Signed-off-by: James Hogan <james.hogan@imgtec.com> Acked-by: Jayachandran C <jchandra@broadcom.com> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13183/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
When expanding the la or dla pseudo-instruction in a delay slot the GNU
assembler will complain should the pseudo-instruction expand to multiple
actual instructions, since only the first of them will be in the delay
slot leading to the pseudo-instruction being only partially executed if
the branch is taken. Use of PTR_LA in the dec int-handler.S leads to
such warnings:
arch/mips/dec/int-handler.S: Assembler messages:
arch/mips/dec/int-handler.S:149: Warning: macro instruction expanded into multiple instructions in a branch delay slot
arch/mips/dec/int-handler.S:198: Warning: macro instruction expanded into multiple instructions in a branch delay slot
Avoid this by open coding the PTR_LA macros.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
A bugfix in v4.8-rc2 introduced a harmless warning when
CONFIG_MEMCG_SWAP is disabled but CONFIG_MEMCG is enabled:
mm/memcontrol.c:4085:27: error: 'mem_cgroup_id_get_online' defined but not used [-Werror=unused-function]
static struct mem_cgroup *mem_cgroup_id_get_online(struct mem_cgroup *memcg)
This moves the function inside of the #ifdef block that hides the
calling function, to avoid the warning.
Fixes: 1f47b61fb407 ("mm: memcontrol: fix swap counter leak on swapout from offline cgroup") Link: http://lkml.kernel.org/r/20160824113733.2776701-1-arnd@arndb.de Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Michal Hocko <mhocko@suse.com> Acked-by: Vladimir Davydov <vdavydov@virtuozzo.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
The #warning was present 10 years ago when the driver first got merged.
As the platform is rather obsolete by now, it seems very unlikely that
the warning will cause anyone to fix the code properly.
kernelci.org reports the warning for every build in the meantime, so
I think it's better to just turn it into a code comment to reduce
noise.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Over the years the code has been changed various times leading to
argc/argv being defined in a different function to where we actually
use the variables. Clean this up by moving them to prom_init_cmdline().
Signed-off-by: John Crispin <john@phrozen.org> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14902/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
kernelci.org reports a warning for this driver, as it copies a local
variable into a 'const char *' string:
drivers/mtd/maps/pmcmsp-flash.c:149:30: warning: passing argument 1 of 'strncpy' discards 'const' qualifier from pointer target type [-Wdiscarded-qualifiers]
Using kstrndup() simplifies the code and avoids the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
kernelci reports a failure of the ip28_defconfig build after upgrading its
gcc version:
arch/mips/sgi-ip22/Platform:29: *** gcc doesn't support needed option -mr10k-cache-barrier=store. Stop.
The problem apparently is that the -mr10k-cache-barrier=store option is now
rejected for CPUs other than r10k. Explicitly including the CPU in the
check fixes this and is safe because both options were introduced in
gcc-4.4.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/15049/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
One of the last remaining failures in kernelci.org is for a gcc bug:
drivers/net/ethernet/qlogic/qlge/qlge_main.c:4819:1: error: insn does not satisfy its constraints:
drivers/net/ethernet/qlogic/qlge/qlge_main.c:4819:1: internal compiler error: in extract_constrain_insn, at recog.c:2190
This is apparently broken in gcc-6 but fixed in gcc-7, and I cannot
reproduce the problem here. However, it is clear that ip27_defconfig
does not actually need this driver as the platform has only PCI-X but
not PCIe, and the qlge adapter in turn is PCIe-only.
The driver was originally enabled in 2010 along with lots of other
drivers.
Fixes: 59d302b342e5 ("MIPS: IP27: Make defconfig useful again.") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/15197/ Signed-off-by: James Hogan <james.hogan@imgtec.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
In linux-4.10-rc, NF_CT_PROTO_UDPLITE and NF_CT_PROTO_DCCP are bool
symbols instead of tristate, and kernelci.org reports a bunch of
warnings for this, like:
arch/mips/configs/malta_kvm_guest_defconfig:63:warning: symbol value 'm' invalid for NF_CT_PROTO_UDPLITE
arch/mips/configs/malta_defconfig:62:warning: symbol value 'm' invalid for NF_CT_PROTO_DCCP
arch/mips/configs/malta_defconfig:63:warning: symbol value 'm' invalid for NF_CT_PROTO_UDPLITE
arch/mips/configs/ip22_defconfig:70:warning: symbol value 'm' invalid for NF_CT_PROTO_DCCP
arch/mips/configs/ip22_defconfig:71:warning: symbol value 'm' invalid for NF_CT_PROTO_UDPLITE
This changes all the MIPS defconfigs with these symbols to have them
built-in.
Fixes: 9b91c96c5d1f ("netfilter: conntrack: built-in support for UDPlite") Fixes: c51d39010a1b ("netfilter: conntrack: built-in support for DCCP") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14999/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
An ancient gcc bug (first reported in 2003) has apparently resurfaced
on MIPS, where kernelci.org reports an overly large stack frame in the
whirlpool hash algorithm:
crypto/wp512.c:987:1: warning: the frame size of 1112 bytes is larger than 1024 bytes [-Wframe-larger-than=]
With some testing in different configurations, I'm seeing large
variations in stack frames size up to 1500 bytes for what should have
around 300 bytes at most. I also checked the reference implementation,
which is essentially the same code but also comes with some test and
benchmarking infrastructure.
It seems that recent compiler versions on at least arm, arm64 and powerpc
have a partial fix for this problem, but enabling "-fsched-pressure", but
even with that fix they suffer from the issue to a certain degree. Some
testing on arm64 shows that the time needed to hash a given amount of
data is roughly proportional to the stack frame size here, which makes
sense given that the wp512 implementation is doing lots of loads for
table lookups, and the problem with the overly large stack is a result
of doing a lot more loads and stores for spilled registers (as seen from
inspecting the object code).
Disabling -fschedule-insns consistently fixes the problem for wp512,
in my collection of cross-compilers, the results are consistently better
or identical when comparing the stack sizes in this function, though
some architectures (notable x86) have schedule-insns disabled by
default.
The four columns are:
default: -O2
press: -O2 -fsched-pressure
nopress: -O2 -fschedule-insns -fno-sched-pressure
nosched: -O2 -no-schedule-insns (disables sched-pressure)
Trying the same test for serpent-generic, the picture is a bit different,
and while -fno-schedule-insns is generally better here than the default,
-fsched-pressure wins overall, so I picked that instead.
I did not do any runtime tests with serpent, so it is possible that stack
frame size does not directly correlate with runtime performance here and
it actually makes things worse, but it's more likely to help here, and
the reduced stack frame size is probably enough reason to apply the patch,
especially given that the crypto code is often used in deep call chains.
A recent change claimed to fix an off-by-one error in the OOB-port
completion handler, but instead introduced such an error. This could
specifically led to modem-status changes going unnoticed, effectively
breaking TIOCMGET.
Note that the offending commit fixes a loop-condition underflow and is
marked for stable, but should not be backported without this fix.
Reported-by: Ben Hutchings <ben@decadent.org.uk> Fixes: 2d380889215f ("USB: serial: digi_acceleport: fix OOB data sanity
check") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
BugLink: http://bugs.launchpad.net/bugs/1673541 Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
The hypercall page only needs to be executable but currently it is setup to
be writable as well. Fix the issue.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Acked-by: Kees Cook <keescook@chromium.org> Reported-by: Stephen Hemminger <stephen@networkplumber.org> Tested-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Recently fallocate patch was merged and it uses
MSDOS_I(inode)->mmu_private at fat_evict_inode(). However,
fat_inode/fsinfo_inode that was introduced in past didn't initialize
MSDOS_I(inode) properly.
With those combinations, it became the cause of accessing random entry
in FAT area.
Link: http://lkml.kernel.org/r/87pohrj4i8.fsf@mail.parknet.co.jp Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp> Reported-by: Moreno Bartalucci <moreno.bartalucci@tecnorama.it> Tested-by: Moreno Bartalucci <moreno.bartalucci@tecnorama.it> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
I ran into this compile warning, which is the result of BUG_ON(1)
not always leading to the compiler treating the code path as
unreachable:
include/linux/ceph/osdmap.h: In function 'ceph_can_shift_osds':
include/linux/ceph/osdmap.h:62:1: error: control reaches end of non-void function [-Werror=return-type]
Using BUG() here avoids the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Cc: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
On my Cherrytrail CUBE iwork8 Air tablet PIPE-A would get stuck on loading
i915 at boot 1 out of every 3 boots, resulting in a non functional LCD.
Once the i915 driver has successfully loaded, the panel can be disabled /
enabled without hitting this issue.
The getting stuck is caused by vlv_init_display_clock_gating() clearing
the DPOUNIT_CLOCK_GATE_DISABLE bit in DSPCLK_GATE_D when called from
chv_pipe_power_well_ops.enable() on driver load, while a pipe is enabled
driving the DSI LCD by the BIOS.
Clearing this bit while DSI is in use is a known issue and
intel_dsi_pre_enable() / intel_dsi_post_disable() already set / clear it
as appropriate.
This commit modifies vlv_init_display_clock_gating() to leave the
DPOUNIT_CLOCK_GATE_DISABLE bit alone fixing the pipe getting stuck.
Changes in v2:
-Replace PIPE-A with "a pipe" or "the pipe" in the commit msg and
comment
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=97330 Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/20161202142904.25613-1-hdegoede@redhat.com Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
(cherry picked from commit 721d484563e1a51ada760089c490cbc47e909756) Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: River Zhou <riverzhou2000@163.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
This patch changes the spinlock to mutex for the available fakelb phy
list. When holding the spinlock the ieee802154_unregister_hw is called
which holding the rtnl_mutex, in that case we get a "BUG: sleeping function
called from invalid context" error. We simple change the spinlock to
mutex which allows to hold the rtnl lock there.
Signed-off-by: Alexander Aring <aar@pengutronix.de> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Having "ret" be a bool type works for everything except
ret = funcs->atomic_check(). The other functions all return zero on
error but ->atomic_check() returns negative error codes. We want to
propagate the error code but instead we return 1.
I found this bug with static analysis and I don't know if it affects
run time.
Fixes: 4cd4df8080a3 ("drm/atomic: Add ->atomic_check() to encoder helpers") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Link: http://patchwork.freedesktop.org/patch/msgid/20170207234601.GA23981@mwanda Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
The current caching state may not be tt_cached, even though the
placement contains TTM_PL_FLAG_CACHED, because placement can contain
multiple caching flags. Trying to swap out such a BO would trip up the
BUG_ON(ttm->caching_state != tt_cached);
in ttm_tt_swapout.
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com> Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com> Reviewed-by: Christian König <christian.koenig@amd.com>. Reviewed-by: Sinclair Yeh <syeh@vmware.com> Signed-off-by: Christian König <christian.koenig@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Rotel RSX-1058 is a receiver with 4 HDMI inputs and a HDMI output, all
1.1.
When a sink that supports deep color is connected to the output, the
receiver will send EDIDs that advertise this capability, even if it
isn't possible with HDMI versions earlier than 1.3.
Currently the kernel is assuming that deep color is possible and the
sink displays an error.
This quirk will make sure that deep color isn't used with this
particular receiver.
Fixes: 7a0baa623446 ("Revert "drm/i915: Disable 12bpc hdmi for now"") Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com> Link: http://patchwork.freedesktop.org/patch/msgid/20170220152545.13153-1-tomeu.vizoso@collabora.com Cc: Matt Horan <matt@matthoran.com> Tested-by: Matt Horan <matt@matthoran.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=99869 Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
The current POST code for the AST2300/2400 family doesn't work properly
if the chip hasn't been initialized previously by either the BMC own FW
or the VBIOS. This fixes it.
Signed-off-by: Y.C. Chen <yc_chen@aspeedtech.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Tested-by: Y.C. Chen <yc_chen@aspeedtech.com> Acked-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
open_key enables access the registers used by enable_mmio
Signed-off-by: Y.C. Chen <yc_chen@aspeedtech.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: Joel Stanley <joel@jms.id.au> Tested-by: Y.C. Chen <yc_chen@aspeedtech.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
The test to see if VGA was already enabled is doing an unnecessary
second test from a register that may or may not have been initialized
to a valid value. Remove it.
Signed-off-by: Y.C. Chen <yc_chen@aspeedtech.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: Joel Stanley <joel@jms.id.au> Tested-by: Y.C. Chen <yc_chen@aspeedtech.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
The issue was found when entering suspend and resume.
It triggers a warning in:
mac80211/key.c: ieee80211_enable_keys()
...
WARN_ON_ONCE(sdata->crypto_tx_tailroom_needed_cnt ||
sdata->crypto_tx_tailroom_pending_dec);
...
It points out sdata->crypto_tx_tailroom_pending_dec isn't cleaned up successfully
in a delayed_work during suspend. Add a flush_delayed_work to fix it.
Signed-off-by: Matt Chen <matt.chen@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
FDT tag parsing is not related to whether BLK_DEV_INITRD is configured
or not, move it out of the corresponding #ifdef/#endif block.
This fixes passing external FDT to the kernel configured w/o
BLK_DEV_INITRD support.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
When first implementing support for changing the output frequency, an
optimization was added to continue the PWM after changing the prescaler
without having to reprogram the ON and OFF registers for the duty cycle,
in case the duty cycle stayed the same. This was flawed, because we
compared the absolute value of the duty cycle in nanoseconds instead of
the ratio to the period.
Fix the problem by removing the shortcut.
Fixes: 01ec8472009c9 ("pwm-pca9685: Support changing the output frequency") Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Thierry Reding <thierry.reding@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
It is not sufficient to just check that the lock pids match when
granting a callback, we also need to ensure that we're granting
the callback on the right file.
Reported-by: Pankaj Singh <psingh.ait@gmail.com> Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
When transport_clear_lun_ref() is shutting down a se_lun via
configfs with new I/O in-flight, it's possible to trigger a
NULL pointer dereference in transport_lookup_cmd_lun() due
to the fact percpu_ref_get() doesn't do any __PERCPU_REF_DEAD
checking before incrementing lun->lun_ref.count after
lun->lun_ref has switched to atomic_t mode.
This results in a NULL pointer dereference as LUN shutdown
code in core_tpg_remove_lun() continues running after the
existing ->release() -> core_tpg_lun_ref_release() callback
completes, and clears the RCU protected se_lun->lun_se_dev
pointer.
During the OOPs, the state of lun->lun_ref in the process
which triggered the NULL pointer dereference looks like
the following on v4.1.y stable code:
To address this bug, use percpu_ref_tryget_live() to ensure
once __PERCPU_REF_DEAD is visable on all CPUs and ->lun_ref
has switched to atomic_t, all new I/Os will fail to obtain
a new lun->lun_ref reference.
Also use an explicit percpu_ref_kill_and_confirm() callback
to block on ->lun_ref_comp to allow the first stage and
associated RCU grace period to complete, and then block on
->lun_ref_shutdown waiting for the final percpu_ref_put()
to drop the last reference via transport_lun_remove_cmd()
before continuing with core_tpg_remove_lun() shutdown.
Reported-by: Rob Millner <rlm@daterainc.com> Tested-by: Rob Millner <rlm@daterainc.com> Cc: Rob Millner <rlm@daterainc.com> Tested-by: Vaibhav Tandon <vst@datera.io> Cc: Vaibhav Tandon <vst@datera.io> Tested-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Avoid that srp_process_rsp() overwrites the status information
in ch if the SRP target response timed out and processing of
another task management function has already started. Avoid that
issuing multiple task management functions concurrently triggers
list corruption. This patch prevents that the following stack
trace appears in the system log:
WARNING: CPU: 8 PID: 9269 at lib/list_debug.c:52 __list_del_entry_valid+0xbc/0xc0
list_del corruption. prev->next should be ffffc90004bb7b00, but was ffff8804052ecc68
CPU: 8 PID: 9269 Comm: sg_reset Tainted: G W 4.10.0-rc7-dbg+ #3
Call Trace:
dump_stack+0x68/0x93
__warn+0xc6/0xe0
warn_slowpath_fmt+0x4a/0x50
__list_del_entry_valid+0xbc/0xc0
wait_for_completion_timeout+0x12e/0x170
srp_send_tsk_mgmt+0x1ef/0x2d0 [ib_srp]
srp_reset_device+0x5b/0x110 [ib_srp]
scsi_ioctl_reset+0x1c7/0x290
scsi_ioctl+0x12a/0x420
sd_ioctl+0x9d/0x100
blkdev_ioctl+0x51e/0x9f0
block_ioctl+0x38/0x40
do_vfs_ioctl+0x8f/0x700
SyS_ioctl+0x3c/0x70
entry_SYSCALL_64_fastpath+0x18/0xad
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com> Cc: Israel Rukshin <israelr@mellanox.com> Cc: Max Gurtovoy <maxg@mellanox.com> Cc: Laurence Oberman <loberman@redhat.com> Cc: Steve Feeley <Steve.Feeley@sandisk.com> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
After srp_process_rsp() returns there is a short time during which
the scsi_host_find_tag() call will return a pointer to the SCSI
command that is being completed. If during that time a duplicate
response is received, avoid that the following call stack appears:
When sending packet to destination that was not resolved yet
via path query, the driver keeps the skb and tries to re-send it
again when the path is resolved.
But when re-sending via dev_queue_xmit the kernel doesn't call
to dev_hard_header, so IPoIB needs to keep 20 bytes in the skb
and to put the destination address inside them.
In that way the dev_start_xmit will have the correct destination,
and the driver won't take the destination from the skb->data, while
nothing exists there, which causes to packet be be dropped.
The test flow is:
1. Run the SM on remote node,
2. Restart the driver.
4. Ping some destination,
3. Observe that first ICMP request will be dropped.
Fixes: fc791b633515 ("IB/ipoib: move back IB LL address into the hard header") Signed-off-by: Erez Shitrit <erezsh@mellanox.com> Signed-off-by: Noa Osherovich <noaos@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Tested-by: Yuval Shaia <yuval.shaia@oracle.com> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
When calling set_mode from sys/fs, the call flow locks the sys/fs lock
first and then tries to lock rtnl_lock (when calling ipoib_set_mod).
On the other hand, the rmmod call flow takes the rtnl_lock first
(when calling unregister_netdev) and then tries to take the sys/fs
lock. Deadlock a->b, b->a.
The problem starts when ipoib_set_mod frees it's rtnl_lck and tries
to get it after that.
Ever since mount propagation was introduced in cases where a mount in
propagated to parent mount mountpoint pair that is already in use the
code has placed the new mount behind the old mount in the mount hash
table.
This implementation detail is problematic as it allows creating
arbitrary length mount hash chains.
Furthermore it invalidates the constraint maintained elsewhere in the
mount code that a parent mount and a mountpoint pair will have exactly
one mount upon them. Making it hard to deal with and to talk about
this special case in the mount code.
Modify mount propagation to notice when there is already a mount at
the parent mount and mountpoint where a new mount is propagating to
and place that preexisting mount on top of the new mount.
Modify unmount propagation to notice when a mount that is being
unmounted has another mount on top of it (and no other children), and
to replace the unmounted mount with the mount on top of it.
Move the MNT_UMUONT test from __lookup_mnt_last into
__propagate_umount as that is the only call of __lookup_mnt_last where
MNT_UMOUNT may be set on any mount visible in the mount hash table.
These modifications allow:
- __lookup_mnt_last to be removed.
- attach_shadows to be renamed __attach_mnt and its shadow
handling to be removed.
- commit_tree to be simplified
- copy_tree to be simplified
The result is an easier to understand tree of mounts that does not
allow creation of arbitrary length hash chains in the mount hash table.
The result is also a very slight userspace visible difference in semantics.
The following two cases now behave identically, where before order
mattered:
case 1: (explicit user action)
B is a slave of A
mount something on A/a , it will propagate to B/a
and than mount something on B/a
case 2: (tucked mount)
B is a slave of A
mount something on B/a
and than mount something on A/a
Histroically umount A/a would fail in case 1 and succeed in case 2.
Now umount A/a succeeds in both configurations.
This very small change in semantics appears if anything to be a bug
fix to me and my survey of userspace leads me to believe that no programs
will notice or care of this subtle semantic change.
v2: Updated to mnt_change_mountpoint to not call dput or mntput
and instead to decrement the counts directly. It is guaranteed
that there will be other references when mnt_change_mountpoint is
called so this is safe.
v3: Moved put_mountpoint under mount_lock in attach_recursive_mnt
As the locking in fs/namespace.c changed between v2 and v3.
v4: Reworked the logic in propagate_mount_busy and __propagate_umount
that detects when a mount completely covers another mount.
v5: Removed unnecessary tests whose result is alwasy true in
find_topper and attach_recursive_mnt.
v6: Document the user space visible semantic difference.
Fixes: b90fa9ae8f51 ("[PATCH] shared mount handling: bind and rbind") Tested-by: Andrei Vagin <avagin@virtuozzo.com> Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Conflicts:
fs/namespace.c Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
When TX descriptors are filled in, the buffer DMA address is split
between the tx_desc->buf_phys_addr field (high-order bits) and
tx_desc->packet_offset field (5 low-order bits).
However, when we re-calculate the DMA address from the TX descriptor in
mvpp2_txq_inc_put(), we do not take tx_desc->packet_offset into
account. This means that when the DMA address is not aligned on a 32
bytes boundary, we end up calling dma_unmap_single() with a DMA address
that was not the one returned by dma_map_single().
This inconsistency is detected by the kernel when DMA_API_DEBUG is
enabled. We fix this problem by properly calculating the DMA address in
mvpp2_txq_inc_put().
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
The current implementation of setup_randomness uses the stack address
and therefore the pointer to the SYSIB 3.2.2 block as input data
address. Furthermore the length of the input data is the number of
virtual-machine description blocks which is typically one.
This means that typically a single zero byte is fed to
add_device_randomness.
Fix both of these and use the address of the first virtual machine
description block as input data address and also use the correct
length.
Fixes: bcfcbb6bae64 ("s390: add system information as device randomness") Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Commit bcfcbb6bae64 ("s390: add system information as device
randomness") intended to add some virtual machine specific information
to the randomness pool.
Unfortunately it uses the page allocator before it is ready to use. In
result the page allocator always returns NULL and the setup_randomness
function never adds anything to the randomness pool.
To fix this use memblock_alloc and memblock_free instead.
Fixes: bcfcbb6bae64 ("s390: add system information as device randomness") Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Return a sensible value if TASK_SIZE if called from a kernel thread.
This gets us around an issue with copy_mount_options that does a magic
size calculation "TASK_SIZE - (unsigned long)data" while in a kernel
thread and data pointing to kernel space.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Since commit dd22f551 "block: Change direct_access calling convention",
the device size calculation in dcssblk_direct_access() is off-by-one.
This results in bdev_direct_access() always returning -ENXIO because the
returned value is not page aligned.
Fix this by adding 1 to the dev_sz calculation.
Fixes: dd22f551 ("block: Change direct_access calling convention") Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
For devices with multiple input queues, tiqdio_call_inq_handlers()
iterates over all input queues and clears the device's DSCI
during each iteration. If the DSCI is re-armed during one
of the later iterations, we therefore do not scan the previous
queues again.
The re-arming also raises a new adapter interrupt. But its
handler does not trigger a rescan for the device, as the DSCI
has already been erroneously cleared.
This can result in queue stalls on devices with multiple
input queues.
Fix it by clearing the DSCI just once, prior to scanning the queues.
As the code is moved in front of the loop, we also need to access
the DSCI directly (ie irq->dsci) instead of going via each queue's
parent pointer to the same irq. This is not a functional change,
and a follow-up patch will clean up the other users.
In practice, this bug only affects CQ-enabled HiperSockets devices,
ie. devices with sysfs-attribute "hsuid" set. Setting a hsuid is
needed for AF_IUCV socket applications that use HiperSockets
communication.
Fixes: 104ea556ee7f ("qdio: support asynchronous delivery of storage blocks") Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
The MKS Instruments SCOM-0800 and SCOM-0801 cards (originally by Tenta
Technologies) are 3U CompactPCI serial cards with 4 and 8 serial ports,
respectively. The first 4 ports are implemented by an OX16PCI954 chip,
and the second 4 ports are implemented by an OX16C954 chip on a local
bus, bridged by the second PCI function of the OX16PCI954. The ports
are jumper-selectable as RS-232 and RS-422/485, and the UARTs use a
non-standard oscillator frequency of 20 MHz (base_baud = 1250000).
Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
BugLink: http://bugs.launchpad.net/bugs/1673538 Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
The driver was calculating the adapter command pagesize indicator from
the system pagesize. However, the buffers the driver allocates are only
one size (SLI4_PAGE_SIZE), so no calculation was necessary.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Cc: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
CC arch/mips/mm/sc-ip22.o
{standard input}: Assembler messages:
{standard input}:132: Error: number (0x9000000080000000) larger than 32 bits
{standard input}:159: Error: number (0x9000000080000000) larger than 32 bits
{standard input}:200: Error: number (0x9000000080000000) larger than 32 bits
scripts/Makefile.build:293: recipe for target 'arch/mips/mm/sc-ip22.o' failed
make[1]: *** [arch/mips/mm/sc-ip22.o] Error 1
MIPS has used .set mips3 to temporarily switch the assembler to 64 bit
mode in 64 bit kernels virtually forever. Binutils 2.25 broke this
behavious partially by happily accepting 64 bit instructions in .set mips3
mode but puking on 64 bit constants when generating 32 bit ELF. Binutils
2.26 restored the old behaviour again.
Fix build with binutils 2.25 by open coding the offending
dli $1, 0x9000000080000000
as
li $1, 0x9000
dsll $1, $1, 48
which is ugly be the only thing that will build on all binutils vintages.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Whenever there is a watchpoint match occurs, hw_breakpoint_handler will
be called by do_break via notifier chains mechanism. If watchpoint is
registered by xmon, hw_breakpoint_handler won't find any associated
perf_event and returns immediately with NOTIFY_STOP. Similarly, do_break
also returns without notifying to xmon.
Solve this by returning NOTIFY_DONE when hw_breakpoint_handler does not
find any perf_event associated with matched watchpoint, rather than
NOTIFY_STOP, which tells the core code to continue calling the other
breakpoint handlers including the xmon one.
Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
projects / mirror_ubuntu-zesty-kernel.git / log