The patch causes a regression, which I cannot find the reason for.
So let's revert for now, as a revert hurts only performance.
Original report:
I was trying to resolve the problem with Oliver but we don't get any conclusion
for 5 months, so I am now sending this to mail list and cdc_acm authors.
I am using simple request-response protocol to obtain the boiller parameters
in constant intervals.
A simple one transaction is:
1. opening the /dev/ttyACM0
2. sending the following 10-bytes request to the device:
unsigned char req[] = {0x02, 0xfe, 0x01, 0x05, 0x08, 0x02, 0x01, 0x69, 0xab, 0x03};
3. reading response (frame of 74 bytes length).
4. closing the descriptor
I am doing this transaction with 5 seconds intervals.
Before the bad commit everything was working correctly: I've got a requests and
a responses in a timely manner.
After the bad commit more time I am using the kernel module, more problems I have.
The graph [2] is showing the problem.
As you can see after module load all seems fine but after about 30 minutes I've got
a plenty of EAGAINs when doing read()'s and trying to read back the data.
When I rmmod and insmod the cdc_acm module again, then the situation is starting
over again: running ok shortly after load, and more time it is running, more EAGAINs
I have when calling read().
As a bonus I can see the problem on the device itself:
The device is configured as you can see here on this screen [3].
It has two transmision LEDs: TX and RX. Blink duration is set for 100ms.
This is a recording before the bad commit when all is working fine: [4]
And this is with the bad commit: [5]
As you can see the TX led is blinking wrongly long (indicating transmission?)
and I have problems doing read() calls (EAGAIN).
usb: Change usb_of_get_companion_dev() place to usb/common
Since renesas_usb3 udc driver calls usb_of_get_companion_dev()
which is on usb/core/of.c, build error like below happens if we
disable CONFIG_USB because the usb/core/ needs CONFIG_USB:
According to the usb/gadget/Kconfig, "NOTE: Gadget support
** DOES NOT ** depend on host-side CONFIG_USB !!".
So, to fix the issue, this patch changes the usb_of_get_companion_dev()
place from usb/core/of.c to usb/common/common.c to be called by both
host and gadget.
Reported-by: John Garry <john.garry@huawei.com> Fixes: 39facfa01c9f ("usb: gadget: udc: renesas_usb3: Add register of usb role switch") Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: xhci: fix interrupt transfer error happened on MTK platforms
The MTK xHCI controller use some reserved bytes in endpoint context for
bandwidth scheduling, so need keep them in xhci_endpoint_copy();
The issue is introduced by:
commit f5249461b504 ("xhci: Clear the host side toggle manually when
endpoint is soft reset")
It resets endpoints and will drop bandwidth scheduling parameters used
by interrupt or isochronous endpoints on MTK xHCI controller. Fixes: f5249461b504 ("xhci: Clear the host side toggle manually when
endpoint is soft reset")
Cc: stable@vger.kernel.org Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> Tested-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jia-Ju Bai [Sat, 1 Sep 2018 08:12:10 +0000 (16:12 +0800)]
usb: cdc-wdm: Fix a sleep-in-atomic-context bug in service_outstanding_interrupt()
wdm_in_callback() is a completion handler function for the USB driver.
So it should not sleep. But it calls service_outstanding_interrupt(),
which calls usb_submit_urb() with GFP_KERNEL.
To fix this bug, GFP_KERNEL is replaced with GFP_ATOMIC.
This bug is found by my static analysis tool DSAC.
Jia-Ju Bai [Sat, 1 Sep 2018 08:25:08 +0000 (16:25 +0800)]
usb: misc: uss720: Fix two sleep-in-atomic-context bugs
async_complete() in uss720.c is a completion handler function for the
USB driver. So it should not sleep, but it is can sleep according to the
function call paths (from bottom to top) in Linux-4.16.
[FUNC] set_1284_register(GFP_KERNEL)
drivers/usb/misc/uss720.c, 372:
set_1284_register in parport_uss720_frob_control
drivers/parport/ieee1284.c, 560:
[FUNC_PTR]parport_uss720_frob_control in parport_ieee1284_ack_data_avail
drivers/parport/ieee1284.c, 577:
parport_ieee1284_ack_data_avail in parport_ieee1284_interrupt
./include/linux/parport.h, 474:
parport_ieee1284_interrupt in parport_generic_irq
drivers/usb/misc/uss720.c, 116:
parport_generic_irq in async_complete
[FUNC] get_1284_register(GFP_KERNEL)
drivers/usb/misc/uss720.c, 382:
get_1284_register in parport_uss720_read_status
drivers/parport/ieee1284.c, 555:
[FUNC_PTR]parport_uss720_read_status in parport_ieee1284_ack_data_avail
drivers/parport/ieee1284.c, 577:
parport_ieee1284_ack_data_avail in parport_ieee1284_interrupt
./include/linux/parport.h, 474:
parport_ieee1284_interrupt in parport_generic_irq
drivers/usb/misc/uss720.c, 116:
parport_generic_irq in async_complete
Note that [FUNC_PTR] means a function pointer call is used.
To fix these bugs, GFP_KERNEL is replaced with GFP_ATOMIC.
These bugs are found by my static analysis tool DSAC.
Jia-Ju Bai [Sat, 1 Sep 2018 09:23:47 +0000 (17:23 +0800)]
usb: host: u132-hcd: Fix a sleep-in-atomic-context bug in u132_get_frame()
i_usX2Y_subs_startup in usbusx2yaudio.c is a completion handler function
for the USB driver. So it should not sleep, but it is can sleep
according to the function call paths (from bottom to top) in Linux-4.16.
[FUNC] msleep
drivers/usb/host/u132-hcd.c, 2558:
msleep in u132_get_frame
drivers/usb/core/hcd.c, 2231:
[FUNC_PTR]u132_get_frame in usb_hcd_get_frame_number
drivers/usb/core/usb.c, 822:
usb_hcd_get_frame_number in usb_get_current_frame_number
sound/usb/usx2y/usbusx2yaudio.c, 303:
usb_get_current_frame_number in i_usX2Y_urb_complete
sound/usb/usx2y/usbusx2yaudio.c, 366:
i_usX2Y_urb_complete in i_usX2Y_subs_startup
Note that [FUNC_PTR] means a function pointer call is used.
To fix this bug, msleep() is replaced with mdelay().
This bug is found by my static analysis tool DSAC.
usb: Avoid use-after-free by flushing endpoints early in usb_set_interface()
The steps taken by usb core to set a new interface is very different from
what is done on the xHC host side.
xHC hardware will do everything in one go. One command is used to set up
new endpoints, free old endpoints, check bandwidth, and run the new
endpoints.
All this is done by xHC when usb core asks the hcd to check for
available bandwidth. At this point usb core has not yet flushed the old
endpoints, which will cause use-after-free issues in xhci driver as
queued URBs are cancelled on a re-allocated endpoint.
To resolve this add a call to usb_disable_interface() which will flush
the endpoints before calling usb_hcd_alloc_bandwidth()
Additional checks in xhci driver will also be implemented to gracefully
handle stale URB cancel on freed and re-allocated endpoints
Randy Dunlap [Mon, 3 Sep 2018 19:51:59 +0000 (12:51 -0700)]
linux/mod_devicetable.h: fix kernel-doc missing notation for typec_device_id
Fix kernel-doc warning for missing struct member description:
../include/linux/mod_devicetable.h:763: warning: Function parameter or member 'driver_data' not described in 'typec_device_id'
Fixes: 8a37d87d72f0c ("usb: typec: Bus type for alternate modes") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com> Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Randy Dunlap [Mon, 3 Sep 2018 19:58:35 +0000 (12:58 -0700)]
usb/typec: fix kernel-doc notation warning for typec_match_altmode
Fix kernel-doc warning for missing function parameter 'mode' description:
../drivers/usb/typec/bus.c:268: warning: Function parameter or member 'mode' not described in 'typec_match_altmode'
Also fix typos for same function documentation.
Fixes: 8a37d87d72f0 ("usb: typec: Bus type for alternate modes") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chunfeng Yun [Wed, 29 Aug 2018 02:36:49 +0000 (10:36 +0800)]
usb: mtu3: fix error of xhci port id when enable U3 dual role
If dual role mode is enabled, when switch u3port0 to device mode,
it will affect port id calculation of host(xHCI), specially when
host supports multi U2 ports or U3 ports, so need enable its dual
role mode, and fix it here.
Oliver Neukum [Thu, 9 Aug 2018 14:03:37 +0000 (16:03 +0200)]
usb: uas: add support for more quirk flags
The hope that UAS devices would be less broken than old style storage
devices has turned out to be unfounded. Make UAS support more of the
quirk flags of the old driver.
Tim Anderson [Thu, 9 Aug 2018 21:55:34 +0000 (14:55 -0700)]
USB: Add quirk to support DJI CineSSD
This device does not correctly handle the LPM operations.
Also, the device cannot handle ATA pass-through commands
and locks up when attempted while running in super speed.
This patch adds the equivalent quirk logic as found in uas.
Signed-off-by: Tim Anderson <tsa@biglakesoftware.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ben Hutchings [Wed, 15 Aug 2018 20:45:37 +0000 (21:45 +0100)]
USB: yurex: Check for truncation in yurex_read()
snprintf() always returns the full length of the string it could have
printed, even if it was truncated because the buffer was too small.
So in case the counter value is truncated, we will over-read from
in_buffer and over-write to the caller's buffer.
I don't think it's actually possible for this to happen, but in case
truncation occurs, WARN and return -EIO.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ben Hutchings [Wed, 15 Aug 2018 20:44:25 +0000 (21:44 +0100)]
USB: yurex: Fix buffer over-read in yurex_write()
If the written data starts with a digit, yurex_write() tries to parse
it as an integer using simple_strtoull(). This requires a null-
terminator, and currently there's no guarantee that there is one.
(The sample program at
https://github.com/NeoCat/YUREX-driver-for-Linux/blob/master/sample/yurex_clock.pl
writes an integer without a null terminator. It seems like it must
have worked by chance!)
Always add a null byte after the written data. Enlarge the buffer
to allow for this.
Cc: stable@vger.kernel.org Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: host: xhci-plat: Iterate over parent nodes for finding quirks
In xhci_plat_probe() both sysdev and pdev->dev are being used
for finding quirks. There are some drivers(like dwc3 host.c)
which adds quirks(like usb3-lpm-capable) into pdev and the logic
present in xhci_plat_probe() checks for quirks in either sysdev
or pdev for finding the quirks. Because of this logic, some of
the quirks are getting missed(usb3-lpm-capable quirk added by dwc3
host.c driver is getting missed).This patch fixes this by iterating
over all the available parents for finding the quirks. In this way
all the quirks which are present in child or parent are correctly
updated.
Mathias Nyman [Fri, 31 Aug 2018 14:24:43 +0000 (17:24 +0300)]
xhci: Fix use after free for URB cancellation on a reallocated endpoint
Make sure the cancelled URB is on the current endpoint ring.
If the endpoint ring has been reallocated since the URB was enqueued
then the URB may contain TD and TRB pointers to a already freed ring.
In this the case return the URB without touching any of the freed ring
structure data.
Don't try to stop the ring. It would be useless.
This can occur if endpoint is not flushed before it is dropped and
re-added, which is the case in usb_set_interface() as xhci does
things in an odd order.
usb: dwc2: Fix call location of dwc2_check_core_endianness
Some SoC/IP as STM32F469, the snpsid can only be read after clock is
enabled, otherwise it will read as 0, and the dwc2_check_core_endianness
will assume the core and AHB have opposite endianness, leading to the
following error:
[ 1.976339] dwc2 50000000.usb: 50000000.usb supply vusb_d not found, using dummy regulator
[ 1.986124] dwc2 50000000.usb: Linked as a consumer to regulator.0
[ 1.992711] dwc2 50000000.usb: 50000000.usb supply vusb_a not found, using dummy regulator
[ 2.003672] dwc2 50000000.usb: dwc2_core_reset: HANG! AHB Idle timeout GRSTCTL GRSTCTL_AHBIDLE
[ 2.015176] dwc2: probe of 50000000.usb failed with error -16
The proposed patch changes the location where dwc2_check_core_endianness
is called, allowing the clock peripheral to be enabled first.
Acked-by: Minas Harutyunyan <hminas@synopsys.com> Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Bruno Meirelles Herrera <bmh@certi.org.br> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"First batch of fixes post-merge window:
- A handful of devicetree changes for i.MX2{3,8} to change over to
new panel bindings. The platforms were moved from legacy
framebuffers to DRM and some development board panels hadn't yet
been converted.
- OMAP fixes related to ti-sysc driver conversion fallout, fixing
some register offsets, no_console_suspend fixes, etc.
- Droid4 changes to fix flaky eMMC probing and vibrator DTS mismerge.
- Fixed 0755->0644 permissions on a newly added file.
- Defconfig changes to make ARM Versatile more useful with QEMU
(helps testing).
- Enable defconfig options for new TI SoC platform that was merged
this window (AM6)"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arm64: defconfig: Enable TI's AM6 SoC platform
ARM: defconfig: Update the ARM Versatile defconfig
ARM: dts: omap4-droid4: Fix emmc errors seen on some devices
ARM: dts: Fix file permission for am335x-osd3358-sm-red.dts
ARM: imx_v6_v7_defconfig: Select CONFIG_DRM_PANEL_SEIKO_43WVF1G
ARM: mxs_defconfig: Select CONFIG_DRM_PANEL_SEIKO_43WVF1G
ARM: dts: imx23-evk: Convert to the new display bindings
ARM: dts: imx23-evk: Move regulators outside simple-bus
ARM: dts: imx28-evk: Convert to the new display bindings
ARM: dts: imx28-evk: Move regulators outside simple-bus
Revert "ARM: dts: imx7d: Invert legacy PCI irq mapping"
arm: dts: am4372: setup rtc as system-power-controller
ARM: dts: omap4-droid4: fix vibrations on Droid 4
bus: ti-sysc: Fix no_console_suspend handling
bus: ti-sysc: Fix module register ioremap for larger offsets
ARM: OMAP2+: Fix module address for modules using mpu_rt_idx
ARM: OMAP2+: Fix null hwmod for ti-sysc debug
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"Speculation:
- Make the microcode check more robust
- Make the L1TF memory limit depend on the internal cache physical
address space and not on the CPUID advertised physical address
space, which might be significantly smaller. This avoids disabling
L1TF on machines which utilize the full physical address space.
- Fix the GDT mapping for EFI calls on 32bit PTI
- Fix the MCE nospec implementation to prevent #GP
Fixes and robustness:
- Use the proper operand order for LSL in the VDSO
- Prevent NMI uaccess race against CR3 switching
- Add a lockdep check to verify that text_mutex is held in
text_poke() functions
- Repair the fallout of giving native_restore_fl() a prototype
- Prevent kernel memory dumps based on usermode RIP
- Wipe KASAN shadow stack before rewinding the stack to prevent false
positives
- Move the AMS GOTO enforcement to the actual build stage to allow
user API header extraction without a compiler
- Fix a section mismatch introduced by the on demand VDSO mapping
change
Miscellaneous:
- Trivial typo, GCC quirk removal and CC_SET/OUT() cleanups"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/pti: Fix section mismatch warning/error
x86/vdso: Fix lsl operand order
x86/mce: Fix set_mce_nospec() to avoid #GP fault
x86/efi: Load fixmap GDT in efi_call_phys_epilog()
x86/nmi: Fix NMI uaccess race against CR3 switching
x86: Allow generating user-space headers without a compiler
x86/dumpstack: Don't dump kernel memory based on usermode RIP
x86/asm: Use CC_SET()/CC_OUT() in __gen_sigismember()
x86/alternatives: Lockdep-enforce text_mutex in text_poke*()
x86/entry/64: Wipe KASAN stack shadow before rewind_stack_do_exit()
x86/irqflags: Mark native_restore_fl extern inline
x86/build: Remove jump label quirk for GCC older than 4.5.2
x86/Kconfig: Fix trivial typo
x86/speculation/l1tf: Increase l1tf memory limit for Nehalem+
x86/spectre: Add missing family 6 check to microcode check
Merge branch 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull core fixes from Thomas Gleixner:
"A small set of updates for core code:
- Prevent tracing in functions which are called from trace patching
via stop_machine() to prevent executing half patched function trace
entries.
- Remove old GCC workarounds
- Remove pointless includes of notifier.h"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
objtool: Remove workaround for unreachable warnings from old GCC
notifier: Remove notifier header file wherever not used
watchdog: Mark watchdog touch functions as notrace
Randy Dunlap [Sun, 2 Sep 2018 04:01:28 +0000 (21:01 -0700)]
x86/pti: Fix section mismatch warning/error
Fix the section mismatch warning in arch/x86/mm/pti.c:
WARNING: vmlinux.o(.text+0x6972a): Section mismatch in reference from the function pti_clone_pgtable() to the function .init.text:pti_user_pagetable_walk_pte()
The function pti_clone_pgtable() references
the function __init pti_user_pagetable_walk_pte().
This is often because pti_clone_pgtable lacks a __init
annotation or the annotation of pti_user_pagetable_walk_pte is wrong.
FATAL: modpost: Section mismatches detected.
Fixes: 85900ea51577 ("x86/pti: Map the vsyscall page if needed") Reported-by: kbuild test robot <lkp@intel.com> Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Andy Lutomirski <luto@kernel.org> Link: https://lkml.kernel.org/r/43a6d6a3-d69d-5eda-da09-0b1c88215a2a@infradead.org
Olof Johansson [Sun, 2 Sep 2018 01:22:19 +0000 (18:22 -0700)]
Merge tag 'omap-for-v4.19/fixes-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omap variants against v4.19-rc1
These are mostly fixes related to using ti-sysc interconnect target module
driver for accessing right register offsets for sgx and cpsw and for
no_console_suspend regression.
There is also a droid4 emmc fix where emmc may not get detected for some
models, and vibrator dts mismerge fix.
And we have a file permission fix for am335x-osd3358-sm-red.dts that
just got added. And we must tag RTC as system-power-controller for
am437x for PMIC to shut down during poweroff.
* tag 'omap-for-v4.19/fixes-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap4-droid4: Fix emmc errors seen on some devices
ARM: dts: Fix file permission for am335x-osd3358-sm-red.dts
arm: dts: am4372: setup rtc as system-power-controller
ARM: dts: omap4-droid4: fix vibrations on Droid 4
bus: ti-sysc: Fix no_console_suspend handling
bus: ti-sysc: Fix module register ioremap for larger offsets
ARM: OMAP2+: Fix module address for modules using mpu_rt_idx
ARM: OMAP2+: Fix null hwmod for ti-sysc debug
Samuel Neves [Sat, 1 Sep 2018 20:14:52 +0000 (21:14 +0100)]
x86/vdso: Fix lsl operand order
In the __getcpu function, lsl is using the wrong target and destination
registers. Luckily, the compiler tends to choose %eax for both variables,
so it has been working so far.
Fixes: a582c540ac1b ("x86/vdso: Use RDPID in preference to LSL when available") Signed-off-by: Samuel Neves <sneves@dei.uc.pt> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Andy Lutomirski <luto@kernel.org> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20180901201452.27828-1-sneves@dei.uc.pt
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"Two small fixes, one for the x86 Stoney SoC to get a more accurate clk
frequency and the other to fix a bad allocation in the Nuvoton NPCM7XX
driver"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: x86: Set default parent to 48Mhz
clk: npcm7xx: fix memory allocation
LuckTony [Fri, 31 Aug 2018 16:55:06 +0000 (09:55 -0700)]
x86/mce: Fix set_mce_nospec() to avoid #GP fault
The trick with flipping bit 63 to avoid loading the address of the 1:1
mapping of the poisoned page while the 1:1 map is updated used to work when
unmapping the page. But it falls down horribly when attempting to directly
set the page as uncacheable.
The problem is that when the cache mode is changed to uncachable, the pages
needs to be flushed from the cache first. But the decoy address is
non-canonical due to bit 63 flipped, and the CLFLUSH instruction throws a
#GP fault.
Add code to change_page_attr_set_clr() to fix the address before calling
flush.
Fixes: 284ce4011ba6 ("x86/memory_failure: Introduce {set, clear}_mce_nospec()") Suggested-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Tony Luck <tony.luck@intel.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Anvin <hpa@zytor.com> Cc: Borislav Petkov <bp@alien8.de> Cc: linux-edac <linux-edac@vger.kernel.org> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Dave Jiang <dave.jiang@intel.com> Link: https://lkml.kernel.org/r/20180831165506.GA9605@agluck-desk
Linus Torvalds [Fri, 31 Aug 2018 16:20:30 +0000 (09:20 -0700)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"A few arm64 fixes came in this week, specifically fixing some nasty
truncation of return values from firmware calls and resolving a
VM_BUG_ON due to accessing uninitialised struct pages corresponding to
NOMAP pages.
Summary:
- Fix typos in SVE documentation
- Fix type-checking and implicit truncation for SMCCC calls
- Force CONFIG_HOLES_IN_ZONE=y so that SLAB doesn't fall over NOMAP
regions"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: mm: always enable CONFIG_HOLES_IN_ZONE
arm/arm64: smccc-1.1: Handle function result as parameters
arm/arm64: smccc-1.1: Make return values unsigned long
Documentation/arm64/sve: Couple of improvements and typos
Joerg Roedel [Fri, 31 Aug 2018 08:05:38 +0000 (10:05 +0200)]
x86/efi: Load fixmap GDT in efi_call_phys_epilog()
When PTI is enabled on x86-32 the kernel uses the GDT mapped in the fixmap
for the simple reason that this address is also mapped for user-space.
The efi_call_phys_prolog()/efi_call_phys_epilog() wrappers change the GDT
to call EFI runtime services and switch back to the kernel GDT when they
return. But the switch-back uses the writable GDT, not the fixmap GDT.
When that happened and and the CPU returns to user-space it switches to the
user %cr3 and tries to restore user segment registers. This fails because
the writable GDT is not mapped in the user page-table, and without a GDT
the fault handlers also can't be launched. The result is a triple fault and
reboot of the machine.
Fix that by restoring the GDT back to the fixmap GDT which is also mapped
in the user page-table.
Linus Torvalds [Fri, 31 Aug 2018 15:45:16 +0000 (08:45 -0700)]
Merge tag 'for-linus-4.19b-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
- minor cleanup avoiding a warning when building with new gcc
- a patch to add a new sysfs node for Xen frontend/backend drivers to
make it easier to obtain the state of a pv device
- two fixes for 32-bit pv-guests to avoid intermediate L1TF vulnerable
PTEs
* tag 'for-linus-4.19b-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
x86/xen: remove redundant variable save_pud
xen: export device state to sysfs
x86/pae: use 64 bit atomic xchg function in native_ptep_get_and_clear
x86/xen: don't write ptes directly in 32-bit PV guests
Linus Torvalds [Fri, 31 Aug 2018 15:38:53 +0000 (08:38 -0700)]
Merge branch 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
- regression fixes for i801 and designware
- better API and leak fix for releasing DMA safe buffers
- better greppable strings for the bitbang algorithm
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: sh_mobile: fix leak when using DMA bounce buffer
i2c: sh_mobile: define start_ch() void as it only returns 0 anyhow
i2c: refactor function to release a DMA safe buffer
i2c: algos: bit: make the error messages grepable
i2c: designware: Re-init controllers with pm_disabled set on resume
i2c: i801: Allow ACPI AML access I/O ports not reserved for SMBus
Andy Lutomirski [Wed, 29 Aug 2018 15:47:18 +0000 (08:47 -0700)]
x86/nmi: Fix NMI uaccess race against CR3 switching
A NMI can hit in the middle of context switching or in the middle of
switch_mm_irqs_off(). In either case, CR3 might not match current->mm,
which could cause copy_from_user_nmi() and friends to read the wrong
memory.
Fix it by adding a new nmi_uaccess_okay() helper and checking it in
copy_from_user_nmi() and in __copy_from_user_nmi()'s callers.
Signed-off-by: Andy Lutomirski <luto@kernel.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Rik van Riel <riel@surriel.com> Cc: Nadav Amit <nadav.amit@gmail.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Jann Horn <jannh@google.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/dd956eba16646fd0b15c3c0741269dfd84452dac.1535557289.git.luto@kernel.org
Ben Hutchings [Wed, 29 Aug 2018 19:43:17 +0000 (20:43 +0100)]
x86: Allow generating user-space headers without a compiler
When bootstrapping an architecture, it's usual to generate the kernel's
user-space headers (make headers_install) before building a compiler. Move
the compiler check (for asm goto support) to the archprepare target so that
it is only done when building code for the target.
Fixes: e501ce957a78 ("x86: Force asm-goto") Reported-by: Helmut Grohne <helmutg@debian.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20180829194317.GA4765@decadent.org.uk
Jann Horn [Tue, 28 Aug 2018 15:49:01 +0000 (17:49 +0200)]
x86/dumpstack: Don't dump kernel memory based on usermode RIP
show_opcodes() is used both for dumping kernel instructions and for dumping
user instructions. If userspace causes #PF by jumping to a kernel address,
show_opcodes() can be reached with regs->ip controlled by the user,
pointing to kernel code. Make sure that userspace can't trick us into
dumping kernel memory into dmesg.
Fixes: 7cccf0725cf7 ("x86/dumpstack: Add a show_ip() function") Signed-off-by: Jann Horn <jannh@google.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Kees Cook <keescook@chromium.org> Reviewed-by: Borislav Petkov <bp@suse.de> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: security@kernel.org Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20180828154901.112726-1-jannh@google.com
Rob Herring [Tue, 28 Aug 2018 20:10:48 +0000 (15:10 -0500)]
of: Add device_type access helper functions
In preparation to remove direct access to device_node.type, add
of_node_is_type() and of_node_get_device_type() helpers to check and
retrieve the device type.
Cc: Frank Rowand <frowand.list@gmail.com> Signed-off-by: Rob Herring <robh@kernel.org>
Mukesh Ojha [Tue, 28 Aug 2018 06:54:54 +0000 (12:24 +0530)]
cpu/hotplug: Remove skip_onerr field from cpuhp_step structure
When notifiers were there, `skip_onerr` was used to avoid calling
particular step startup/teardown callbacks in the CPU up/down rollback
path, which made the hotplug asymmetric.
As notifiers are gone now after the full state machine conversion, the
`skip_onerr` field is no longer required.
James Morse [Thu, 30 Aug 2018 15:05:32 +0000 (16:05 +0100)]
arm64: mm: always enable CONFIG_HOLES_IN_ZONE
Commit 6d526ee26ccd ("arm64: mm: enable CONFIG_HOLES_IN_ZONE for NUMA")
only enabled HOLES_IN_ZONE for NUMA systems because the NUMA code was
choking on the missing zone for nomap pages. This problem doesn't just
apply to NUMA systems.
If the architecture doesn't set HAVE_ARCH_PFN_VALID, pfn_valid() will
return true if the pfn is part of a valid sparsemem section.
When working with multiple pages, the mm code uses pfn_valid_within()
to test each page it uses within the sparsemem section is valid. On
most systems memory comes in MAX_ORDER_NR_PAGES chunks which all
have valid/initialised struct pages. In this case pfn_valid_within()
is optimised out.
Systems where this isn't true (e.g. due to nomap) should set
HOLES_IN_ZONE and provide HAVE_ARCH_PFN_VALID so that mm tests each
page as it works with it.
Currently non-NUMA arm64 systems can't enable HOLES_IN_ZONE, leading to
a VM_BUG_ON():
Linus Torvalds [Fri, 31 Aug 2018 04:18:05 +0000 (21:18 -0700)]
Merge tag 'drm-fixes-2018-08-31' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Regular fixes pull:
- Mediatek has a bunch of fixes to their RDMA and Overlay engines.
- i915 has some Cannonlake/Geminilake watermark workarounds, LSPCON
fix, HDCP free fix, audio fix and a ppgtt reference counting fix.
- amdgpu has some SRIOV, Kasan, memory leaks and other misc fixes"
* tag 'drm-fixes-2018-08-31' of git://anongit.freedesktop.org/drm/drm: (35 commits)
drm/i915/audio: Hook up component bindings even if displays are disabled
drm/i915: Increase LSPCON timeout
drm/i915: Stop holding a ref to the ppgtt from each vma
drm/i915: Free write_buf that we allocated with kzalloc.
drm/i915: Fix glk/cnl display w/a #1175
drm/amdgpu: Need to set moved to true when evict bo
drm/amdgpu: Remove duplicated power source update
drm/amd/display: Fix memory leak caused by missed dc_sink_release
drm/amdgpu: fix holding mn_lock while allocating memory
drm/amdgpu: Power on uvd block when hw_fini
drm/amdgpu: Update power state at the end of smu hw_init.
drm/amdgpu: Fix vce initialize failed on Kaveri/Mullins
drm/amdgpu: Enable/disable gfx PG feature in rlc safe mode
drm/amdgpu: Adjust the VM size based on system memory size v2
drm/mediatek: fix connection from RDMA2 to DSI1
drm/mediatek: update some variable name from ovl to comp
drm/mediatek: use layer_nr function to get layer number to init plane
drm/mediatek: add function to return RDMA layer number
drm/mediatek: add function to return OVL layer number
drm/mediatek: add function to get layer number for component
...
Linus Torvalds [Fri, 31 Aug 2018 01:02:02 +0000 (18:02 -0700)]
Merge tag 'pm-4.19-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These address a corner case in the menu cpuidle governor and fix error
handling in the PM core's generic clock management code.
Specifics:
- Make the menu cpuidle governor avoid stopping the scheduler tick if
the predicted idle duration exceeds the tick period length, but the
selected idle state is shallow and deeper idle states with high
target residencies are available (Rafael Wysocki).
- Make the PM core's generic clock management code use a proper data
type for one variable to make error handling work (Dan Carpenter)"
* tag 'pm-4.19-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpuidle: menu: Retain tick when shallow state is selected
PM / clk: signedness bug in of_pm_clk_add_clks()
Akshu Agrawal [Tue, 21 Aug 2018 06:51:57 +0000 (12:21 +0530)]
clk: x86: Set default parent to 48Mhz
System clk provided in ST soc can be set to:
48Mhz, non-spread
25Mhz, spread
To get accurate rate, we need it to set it at non-spread
option which is 48Mhz.
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com> Reviewed-by: Daniel Kurtz <djkurtz@chromium.org> Fixes: 421bf6a1f061 ("clk: x86: Add ST oscout platform clock") Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Wolfram Sang [Fri, 24 Aug 2018 14:52:46 +0000 (16:52 +0200)]
i2c: sh_mobile: fix leak when using DMA bounce buffer
We only freed the bounce buffer after successful DMA, missing the cases
where DMA setup may have gone wrong. Use a better location which always
gets called after each message and use 'stop_after_dma' as a flag for a
successful transfer.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Wolfram Sang [Fri, 24 Aug 2018 14:52:45 +0000 (16:52 +0200)]
i2c: sh_mobile: define start_ch() void as it only returns 0 anyhow
After various refactoring over the years, start_ch() doesn't return
errno anymore, so make the function return void. This saves the error
handling when calling it which in turn eases cleanup of resources of a
future patch.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Wolfram Sang [Fri, 24 Aug 2018 14:52:44 +0000 (16:52 +0200)]
i2c: refactor function to release a DMA safe buffer
a) rename to 'put' instead of 'release' to match 'get' when obtaining
the buffer
b) change the argument order to have the buffer as first argument
c) add a new argument telling the function if the message was
transferred. This allows the function to be used also in cases
where setting up DMA failed, so the buffer needs to be freed without
syncing to the message buffer.
Also convert the only user.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Hans de Goede [Wed, 29 Aug 2018 13:06:31 +0000 (15:06 +0200)]
i2c: designware: Re-init controllers with pm_disabled set on resume
On Bay Trail and Cherry Trail devices we set the pm_disabled flag for I2C
busses which the OS shares with the PUNIT as these need special handling.
Until now we called dev_pm_syscore_device(dev, true) for I2C controllers
with this flag set to keep these I2C controllers always on.
After commit 12864ff8545f ("ACPI / LPSS: Avoid PM quirks on suspend and
resume from hibernation"), this no longer works. This commit modifies
lpss_iosf_exit_d3_state() to only run if lpss_iosf_enter_d3_state() has ran
before it, so that it does not run on a resume from hibernate (or from S3).
On these systems the conditions for lpss_iosf_enter_d3_state() to run
never become true, so lpss_iosf_exit_d3_state() never gets called and
the 2 LPSS DMA controllers never get forced into D0 mode, instead they
are left in their default automatic power-on when needed mode.
The not forcing of D0 mode for the DMA controllers enables these systems
to properly enter S0ix modes, which is a good thing.
But after entering S0ix modes the I2C controller connected to the PMIC
no longer works, leading to e.g. broken battery monitoring.
The _PS3 method for this I2C controller looks like this:
Method (_PS3, 0, NotSerialized) // _PS3: Power State 3
{
If ((((PMID == 0x04) || (PMID == 0x05)) || (PMID == 0x06)))
{
Return (Zero)
}
Where PMID = 0x05, so we enter the Return (Zero) path on these systems.
So even if we were to not call dev_pm_syscore_device(dev, true) the
I2C controller will be left in D0 rather then be switched to D3.
Yet on other Bay and Cherry Trail devices S0ix is not entered unless *all*
I2C controllers are in D3 mode. This combined with the I2C controller no
longer working now that we reach S0ix states on these systems leads to me
believing that the PUNIT itself puts the I2C controller in D3 when all
other conditions for entering S0ix states are true.
Since now the I2C controller is put in D3 over a suspend/resume we must
re-initialize it afterwards and that does indeed fix it no longer working.
This commit implements this fix by:
1) Making the suspend_late callback a no-op if pm_disabled is set and
making the resume_early callback skip the clock re-enable (since it now was
not disabled) while still doing the necessary I2C controller re-init.
2) Removing the dev_pm_syscore_device(dev, true) call, so that the suspend
and resume callbacks are actually called. Normally this would cause the
ACPI pm code to call _PS3 putting the I2C controller in D3, wreaking havoc
since it is shared with the PUNIT, but in this special case the _PS3 method
is a no-op so we can safely allow a "fake" suspend / resume.
Fixes: 12864ff8545f ("ACPI / LPSS: Avoid PM quirks on suspend and resume ...") Link: https://bugzilla.kernel.org/show_bug.cgi?id=200861 Cc: 4.15+ <stable@vger.kernel.org> # 4.15+ Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Mika Westerberg [Thu, 30 Aug 2018 08:50:13 +0000 (11:50 +0300)]
i2c: i801: Allow ACPI AML access I/O ports not reserved for SMBus
Commit 7ae81952cda ("i2c: i801: Allow ACPI SystemIO OpRegion to conflict
with PCI BAR") made it possible for AML code to access SMBus I/O ports
by installing custom SystemIO OpRegion handler and blocking i80i driver
access upon first AML read/write to this OpRegion.
However, while ThinkPad T560 does have SystemIO OpRegion declared under
the SMBus device, it does not access any of the SMBus registers:
Problem with the current approach is that it blocks all I/O port access
and because this system has touchpad connected to the SMBus controller
after first AML access (happens during suspend/resume cycle) the
touchpad fails to work anymore.
Fix this so that we allow ACPI AML I/O port access if it does not touch
the region reserved for the SMBus.
Fixes: 7ae81952cda ("i2c: i801: Allow ACPI SystemIO OpRegion to conflict with PCI BAR") Link: https://bugzilla.kernel.org/show_bug.cgi?id=200737 Reported-by: Yussuf Khalil <dev@pp3345.net> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Jean Delvare <jdelvare@suse.de> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
* tag 'for-linus-20180830' of git://git.kernel.dk/linux-block:
cdrom: Fix info leak/OOB read in cdrom_ioctl_drive_status
nvmet: free workqueue object if module init fails
nvme-fcloop: Fix dropped LS's to removed target port
nvme-pci: add a memory barrier to nvme_dbbuf_update_and_check_event
block: bsg: move atomic_t ref_count variable to refcount API
block: remove unnecessary condition check
ata: ftide010: Add a quirk for SQ201
blk-wbt: remove dead code
blk-wbt: improve waking of tasks
blk-wbt: abstract out end IO completion handler
xen/blkback: remove unused pers_gnts_lock from struct xen_blkif_ring
xen/blkback: move persistent grants flags to bool
xen/blkfront: reorder tests in xlblk_init()
xen/blkfront: cleanup stale persistent grants
xen/blkback: don't keep persistent grants too long
Linus Torvalds [Thu, 30 Aug 2018 17:05:12 +0000 (10:05 -0700)]
Merge tag 'mtd/for-4.19-rc2' of git://git.infradead.org/linux-mtd
Pull mtd fixes from Boris Brezillon:
"Raw NAND fixes:
- denali: Fix a regression caused by the nand_scan() rework
- docg4: Fix a build error when gcc decides to not iniline some
functions (can be reproduced with gcc 4.1.2):
* tag 'mtd/for-4.19-rc2' of git://git.infradead.org/linux-mtd:
mtd: rawnand: denali: do not pass zero maxchips to nand_scan()
mtd: rawnand: docg4: Remove wrong __init annotations
Masahiro Yamada [Mon, 27 Aug 2018 03:39:43 +0000 (12:39 +0900)]
objtool: Remove workaround for unreachable warnings from old GCC
Commit cafa0010cd51 ("Raise the minimum required gcc version to 4.6")
bumped the minimum GCC version to 4.6 for all architectures.
This effectively reverts commit da541b20021c ("objtool: Skip unreachable
warnings for GCC 4.4 and older"), which was a workaround for GCC 4.4 or
older.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Michal Marek <michal.lkml@markovi.net> Cc: linux-kbuild@vger.kernel.org Link: https://lkml.kernel.org/r/1535341183-19994-1-git-send-email-yamada.masahiro@socionext.com
watchdog: Mark watchdog touch functions as notrace
Some architectures need to use stop_machine() to patch functions for
ftrace, and the assumption is that the stopped CPUs do not make function
calls to traceable functions when they are in the stopped state.
Commit ce4f06dcbb5d ("stop_machine: Touch_nmi_watchdog() after
MULTI_STOP_PREPARE") added calls to the watchdog touch functions from
the stopped CPUs and those functions lack notrace annotations. This
leads to crashes when enabling/disabling ftrace on ARM kernels built
with the Thumb-2 instruction set.
Fix it by adding the necessary notrace annotations.
Fixes: ce4f06dcbb5d ("stop_machine: Touch_nmi_watchdog() after MULTI_STOP_PREPARE") Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: oleg@redhat.com Cc: tj@kernel.org Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20180821152507.18313-1-vincent.whitchurch@axis.com
Jann Horn [Tue, 28 Aug 2018 18:40:33 +0000 (20:40 +0200)]
x86/entry/64: Wipe KASAN stack shadow before rewind_stack_do_exit()
Reset the KASAN shadow state of the task stack before rewinding RSP.
Without this, a kernel oops will leave parts of the stack poisoned, and
code running under do_exit() can trip over such poisoned regions and cause
nonsensical false-positive KASAN reports about stack-out-of-bounds bugs.
This does not wipe the exception stacks; if an oops happens on an exception
stack, it might result in random KASAN false-positives from other tasks
afterwards. This is probably relatively uninteresting, since if the kernel
oopses on an exception stack, there are most likely bigger things to worry
about. It'd be more interesting if vmapped stacks and KASAN were
compatible, since then handle_stack_overflow() would oops from exception
stack context.
Fixes: 2deb4be28077 ("x86/dumpstack: When OOPSing, rewind the stack before do_exit()") Signed-off-by: Jann Horn <jannh@google.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Andrey Ryabinin <aryabinin@virtuozzo.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Alexander Potapenko <glider@google.com> Cc: Kees Cook <keescook@chromium.org> Cc: kasan-dev@googlegroups.com Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20180828184033.93712-1-jannh@google.com
Linus Torvalds [Thu, 30 Aug 2018 01:41:48 +0000 (18:41 -0700)]
Merge tag 'riscv-for-linus-4.19-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux
Pull RISC-V fixes from Palmer Dabbelt:
"RISC-V Fixes and Cleanups for 4.19-rc2
This contains a handful of patches that filtered their way in during
the merge window but just didn't make the deadline. It includes:
- Additional documentation in the riscv,cpu-intc device tree binding
that resulted from some feedback I missed in the original patch
set.
- A build fix that provides the definition of tlb_flush() before
including tlb.h, which fixes a RISC-V build regression introduced
during this merge window.
- A cosmetic cleanup to sys_riscv_flush_icache()"
* tag 'riscv-for-linus-4.19-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux:
RISC-V: Use a less ugly workaround for unused variable warnings
riscv: tlb: Provide definition of tlb_flush() before including tlb.h
dt-bindings: riscv,cpu-intc: Cleanups from a missed review
Dave Airlie [Thu, 30 Aug 2018 01:34:55 +0000 (11:34 +1000)]
Merge tag 'drm-intel-fixes-2018-08-29' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
- fix for GLK and CNL watermark workaround
- fix for display affecting NUCs with LSPCON
- freeing an allocated write_buf on hdcp
- audio hook when display is disabled
- vma stop holding ppgtt reference
Dave Airlie [Thu, 30 Aug 2018 01:30:02 +0000 (11:30 +1000)]
Merge branch 'drm-fixes-4.19' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
Fixes for 4.19:
- SR-IOV fixes
- Kasan and page fault fix on device removal
- S3 stability fix for CZ/ST
- VCE regression fixes for CIK parts
- Avoid holding the mn_lock when allocating memory
- DC memory leak fix
- BO eviction fix
Ard Biesheuvel [Wed, 29 Aug 2018 06:47:53 +0000 (08:47 +0200)]
powerpc: disable support for relative ksymtab references
The newly added code that emits ksymtab entries as pairs of 32-bit
relative references interacts poorly with the way powerpc lays out its
address space: when a module exports a per-CPU variable, the primary
module region covering the ksymtab entry -and thus the 32-bit relative
reference- is too far away from the actual per-CPU variable's base
address (to which the per-CPU offsets are applied to obtain the
respective address of each CPU's copy), resulting in corruption when the
module loader attempts to resolve symbol references of modules that are
loaded on top and link to the exported per-CPU symbol.
So let's disable this feature on powerpc. Even though it implements
CONFIG_RELOCATABLE, it does not implement CONFIG_RANDOMIZE_BASE and so
KASLR kernels (which are the main target of the feature) do not exist on
powerpc anyway.
Reported-by: Andreas Schwab <schwab@linux-m68k.org> Suggested-by: Nicholas Piggin <nicholas.piggin@gmail.com> Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Wed, 29 Aug 2018 21:51:32 +0000 (14:51 -0700)]
Merge tag 'nios2-v4.19-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/lftan/nios2
Pull nios2 fix from Ley Foon Tan:
"remove duplicate DEBUG_STACK_USAGE symbol defintions"
* tag 'nios2-v4.19-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/lftan/nios2:
nios2: kconfig: remove duplicate DEBUG_STACK_USAGE symbol defintions
Chris Wilson [Fri, 17 Aug 2018 10:02:41 +0000 (11:02 +0100)]
drm/i915/audio: Hook up component bindings even if displays are disabled
If the display has been disabled by modparam, we still want to connect
together the HW bits and bobs with the associated drivers so that we can
continue to manage their runtime power gating.
Fixes: 108109444ff6 ("drm/i915: Check num_pipes before initializing audio component") Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Imre Deak <imre.deak@intel.com> Cc: Takashi Iwai <tiwai@suse.de> Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: Elaine Wang <elaine.wang@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180817100241.4628-1-chris@chris-wilson.co.uk
(cherry picked from commit 35a5fd9ebfa93758ca579e30f337b6c9126d995b) Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Fredrik Schön [Fri, 17 Aug 2018 20:07:28 +0000 (22:07 +0200)]
drm/i915: Increase LSPCON timeout
100 ms is not enough time for the LSPCON adapter on Intel NUC devices to
settle. This causes dropped display modes at boot or screen reconfiguration.
Empirical testing can reproduce the error up to a timeout of 190 ms. Basic
boot and stress testing at 200 ms has not (yet) failed.
Increase timeout to 400 ms to get some margin of error.
Changes from v1:
The initial suggestion of 1000 ms was lowered due to concerns about delaying
valid timeout cases.
Update patch metadata.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107503
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1570392 Fixes: 357c0ae9198a ("drm/i915/lspcon: Wait for expected LSPCON mode to settle") Cc: Shashank Sharma <shashank.sharma@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Jani Nikula <jani.nikula@intel.com> Cc: <stable@vger.kernel.org> # v4.11+ Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Reviewed-by: Shashank Sharma <shashank.sharma@intel.com> Signed-off-by: Fredrik Schön <fredrik.schon@gmail.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180817200728.8154-1-fredrik.schon@gmail.com
(cherry picked from commit 59f1c8ab30d6f9042562949f42cbd3f3cf69de94) Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Chris Wilson [Thu, 16 Aug 2018 07:34:46 +0000 (08:34 +0100)]
drm/i915: Stop holding a ref to the ppgtt from each vma
The context owns both the ppgtt and the vma within it, and our activity
tracking on the context ensures that we do not release active ppgtt. As
the context fulfils our obligations for active memory tracking, we can
relinquish the reference from the vma.
This fixes a silly transient refleak from closed vma being kept alive
until the entire system was idle, keeping all vm alive as well.
Reported-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Testcase: igt/gem_ctx_create/files Fixes: 3365e2268b6b ("drm/i915: Lazily unbind vma on close") Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Cc: Paulo Zanoni <paulo.r.zanoni@intel.com> Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com> Tested-by: Mika Kuoppala <mika.kuoppala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180816073448.19396-1-chris@chris-wilson.co.uk
(cherry picked from commit a4417b7b419a68540ad7945ac4efbb39d19afa63) Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Linus Torvalds [Wed, 29 Aug 2018 20:38:39 +0000 (13:38 -0700)]
Merge branch 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fixes from Herbert Xu:
- Check for the right CPU feature bit in sm4-ce on arm64.
- Fix scatterwalk WARN_ON in aes-gcm-ce on arm64.
- Fix unaligned fault in aesni on x86.
- Fix potential NULL pointer dereference on exit in chtls.
- Fix DMA mapping direction for RSA in caam.
- Fix error path return value for xts setkey in caam.
- Fix address endianness when DMA unmapping in caam.
- Fix sleep-in-atomic in vmx.
- Fix command corruption when queue is full in cavium/nitrox.
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: cavium/nitrox - fix for command corruption in queue full case with backlog submissions.
crypto: vmx - Fix sleep-in-atomic bugs
crypto: arm64/aes-gcm-ce - fix scatterwalk API violation
crypto: aesni - Use unaligned loads from gcm_context_data
crypto: chtls - fix null dereference chtls_free_uld()
crypto: arm64/sm4-ce - check for the right CPU feature bit
crypto: caam - fix DMA mapping direction for RSA forms 2 & 3
crypto: caam/qi - fix error path in xts setkey
crypto: caam/jr - fix descriptor DMA unmapping
Linus Walleij [Mon, 27 Aug 2018 13:27:08 +0000 (15:27 +0200)]
ARM: defconfig: Update the ARM Versatile defconfig
This updates the ARM Versatile defconfig to the latest
Kconfig structural changes and adds the DUMB VGA bridge
driver so that VGA works out of the box, e.g. with QEMU.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Wed, 29 Aug 2018 18:50:14 +0000 (11:50 -0700)]
Merge tag 'imx-fixes-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
i.MX fixes for 4.19:
- i.MX display folks decided to switch MXS display driver from legacy
FB to DRM during 4.19 merge window. It leads to a fallout on some
Freescale/NXP development boards with Seiko 43WVF1G panel, because
this DRM panel driver is not enabled in i.MX defconfig. Here is
a series from Fabio to convert i.MX23/28 EVK DT to Seiko 43WVF1G
panel bindings and enable the panel driver in i.MX defconfig, so that
users can still get functional LCD on these boards by default.
- A fix from Leonard to revert incorrect legacy PCI irq mapping in
i.MX7 device tree, that was caused by document errors.
* tag 'imx-fixes-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx_v6_v7_defconfig: Select CONFIG_DRM_PANEL_SEIKO_43WVF1G
ARM: mxs_defconfig: Select CONFIG_DRM_PANEL_SEIKO_43WVF1G
ARM: dts: imx23-evk: Convert to the new display bindings
ARM: dts: imx23-evk: Move regulators outside simple-bus
ARM: dts: imx28-evk: Convert to the new display bindings
ARM: dts: imx28-evk: Move regulators outside simple-bus
Revert "ARM: dts: imx7d: Invert legacy PCI irq mapping"
Jens Axboe [Wed, 29 Aug 2018 17:05:20 +0000 (11:05 -0600)]
Merge branch 'nvme-4.19' of git://git.infradead.org/nvme into for-linus
Pull NVMe fixes from Christoph.
* 'nvme-4.19' of git://git.infradead.org/nvme:
nvmet: free workqueue object if module init fails
nvme-fcloop: Fix dropped LS's to removed target port
nvme-pci: add a memory barrier to nvme_dbbuf_update_and_check_event
Scott Bauer [Thu, 26 Apr 2018 17:51:08 +0000 (11:51 -0600)]
cdrom: Fix info leak/OOB read in cdrom_ioctl_drive_status
Like d88b6d04: "cdrom: information leak in cdrom_ioctl_media_changed()"
There is another cast from unsigned long to int which causes
a bounds check to fail with specially crafted input. The value is
then used as an index in the slot array in cdrom_slot_status().
Signed-off-by: Scott Bauer <scott.bauer@intel.com> Signed-off-by: Scott Bauer <sbauer@plzdonthack.me> Cc: stable@vger.kernel.org Signed-off-by: Jens Axboe <axboe@kernel.dk>
Johan Hovold [Mon, 27 Aug 2018 08:21:45 +0000 (10:21 +0200)]
of: add helper to lookup compatible child node
Add of_get_compatible_child() helper that can be used to lookup
compatible child nodes.
Several drivers currently use of_find_compatible_node() to lookup child
nodes while failing to notice that the of_find_ functions search the
entire tree depth-first (from a given start node) and therefore can
match unrelated nodes. The fact that these functions also drop a
reference to the node they start searching from (e.g. the parent node)
is typically also overlooked, something which can lead to use-after-free
bugs.
Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Rob Herring <robh@kernel.org>
Marc Zyngier [Fri, 24 Aug 2018 14:08:29 +0000 (15:08 +0100)]
arm/arm64: smccc-1.1: Make return values unsigned long
An unfortunate consequence of having a strong typing for the input
values to the SMC call is that it also affects the type of the
return values, limiting r0 to 32 bits and r{1,2,3} to whatever
was passed as an input.
Let's turn everything into "unsigned long", which satisfies the
requirements of both architectures, and allows for the full
range of return values.
Reported-by: Julien Grall <julien.grall@arm.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
usb: dwc3: pci: Fix return value check in dwc3_byt_enable_ulpi_refclock()
In case of error, the function pcim_iomap() returns NULL pointer not
ERR_PTR(). The IS_ERR() test in the return value check should be
replaced with NULL test.
Fixes: 7740d04d901d ("usb: dwc3: pci: Enable ULPI Refclk on platforms where the firmware does not") Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
usb: gadget: udc: renesas_usb3: fix maxpacket size of ep0
This patch fixes an issue that maxpacket size of ep0 is incorrect
for SuperSpeed. Otherwise, CDC NCM class with SuperSpeed doesn't
work correctly on this driver because its control read data size
is more than 64 bytes.
Commit f16443a034c7 ("USB: gadgetfs, dummy-hcd, net2280: fix locking
for callbacks") was based on a serious misunderstanding. It
introduced regressions into both the dummy-hcd and net2280 drivers.
The problem in dummy-hcd was fixed by commit 7dbd8f4cabd9 ("USB:
dummy-hcd: Fix erroneous synchronization change"), but the problem in
net2280 remains. Namely: the ->disconnect(), ->suspend(), ->resume(),
and ->reset() callbacks must be invoked without the private lock held;
otherwise a deadlock will occur when the callback routine tries to
interact with the UDC driver.
This patch largely is a reversion of the relevant parts of f16443a034c7. It also drops the private lock around the calls to
->suspend() and ->resume() (something the earlier patch forgot to do).
This is safe from races with device interrupts because it occurs
within the interrupt handler.
Finally, the patch changes where the ->disconnect() callback is
invoked when net2280_pullup() turns the pullup off. Rather than
making the callback from within stop_activity() at a time when dropping
the private lock could be unsafe, the callback is moved to a point
after the lock has already been dropped.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Fixes: f16443a034c7 ("USB: gadgetfs, dummy-hcd, net2280: fix locking for callbacks") Reported-by: D. Ziesche <dziesche@zes.com> Tested-by: D. Ziesche <dziesche@zes.com> CC: <stable@vger.kernel.org> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Arnd Bergmann [Mon, 13 Aug 2018 21:56:55 +0000 (23:56 +0200)]
usb: dwc3: of-simple: avoid unused function warnings
An incorrect #ifdef caused a pair of harmless warnings when CONFIG_PM_SLEEP
is disabled:
drivers/usb/dwc3/dwc3-of-simple.c:223:12: error: 'dwc3_of_simple_resume' defined but not used [-Werror=unused-function]
static int dwc3_of_simple_resume(struct device *dev)
^~~~~~~~~~~~~~~~~~~~~
drivers/usb/dwc3/dwc3-of-simple.c:213:12: error: 'dwc3_of_simple_suspend' defined but not used [-Werror=unused-function]
static int dwc3_of_simple_suspend(struct device *dev)
Since the #ifdef method is generally hard to get right, use
a simpler __maybe_unused annotation here to let the compiler
drop the unused functions silently. This also improves
compile-time coverage.
Fixes: 76251db86561 ("usb: dwc3: of-simple: reset host controller at suspend/resume") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Linus Torvalds [Tue, 28 Aug 2018 23:11:34 +0000 (16:11 -0700)]
Merge branch 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal
Pull thermal fixes from Eduardo Valentin:
"Minor fixes to OF thermal, qoriq, and rcar drivers"
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal:
thermal: of-thermal: disable passive polling when thermal zone is disabled
thermal: rcar_gen3_thermal: convert to SPDX identifiers
thermal: rcar_thermal: convert to SPDX identifiers
thermal: qoriq: Switch to SPDX identifier
thermal: qoriq: Simplify the 'site' variable assignment
thermal: qoriq: Use devm_thermal_zone_of_sensor_register()
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
Notice that, currently, there is a bug during the allocation:
sizeof(npcm7xx_clk_data) should be sizeof(*npcm7xx_clk_data)
Fix this bug by using struct_size() in kzalloc()
This issue was detected with the help of Coccinelle.
Cc: stable@vger.kernel.org Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Reviewed-by: Kees Cook <keescook@chromium.org> Reviewed-by: Avi Fishman <avifishman70@gmail.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Colin Ian King [Tue, 28 Aug 2018 16:10:46 +0000 (17:10 +0100)]
x86/xen: remove redundant variable save_pud
Variable save_pud is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
variable 'save_pud' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
projects / mirror_ubuntu-focal-kernel.git / log