Marcel Holtmann [Tue, 20 Oct 2015 00:30:47 +0000 (02:30 +0200)]
Bluetooth: Add support setup stage internal notification event
Before the vendor specific setup stage is triggered call back into the
core to trigger an internal notification event. That event is used to
send an index update to the monitor interface. With that specific event
it is possible to update userspace with manufacturer information before
any HCI command has been executed. This is useful for early stage
debugging of vendor specific initialization sequences.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Santtu Rekilä [Mon, 5 Oct 2015 12:45:27 +0000 (15:45 +0300)]
Bluetooth: btusb: Add support for Foxconn/Lenovo BCM43142A0 (105b:e065)
Recently salvaged this 'BCM43142A0' WiFi/Bluetooth module from a Lenovo laptop
and noticed it doesn't work automatically, because the USB IDs are missing
from btusb.c.
Plugging in the adapter on Linux 4.1 (dmesg):
usb 3-3.3.3: new full-speed USB device number 90 using xhci_hcd
usb 3-3.3.3: New USB device found, idVendor=105b, idProduct=e065
usb 3-3.3.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 3-3.3.3: Product: BCM43142A0
usb 3-3.3.3: Manufacturer: Broadcom Corp
usb 3-3.3.3: SerialNumber: 0090A286559E
Support for the chipset was added in commit 88f9b65 and a similar BCM43142
based device was added in commit 8f0c304.
To work around the issue, I got the firmware
(BCM43142A0_001.001.011.0122.0153) off a Windows installation of Broadcom
bluetooth driver and converted it to a .hcd -file via. hex2hcd and placed it
in /lib/firmware/brcm/BCM.hcd. After that:
$ echo "105b e065 0 19ff 0239" > /sys/bus/usb/drivers/btusb/new_id
...(plug in the adapter)
usb 3-3.3.3: new full-speed USB device number 91 using xhci_hcd
usb 3-3.3.3: New USB device found, idVendor=105b, idProduct=e065
usb 3-3.3.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 3-3.3.3: Product: BCM43142A0
usb 3-3.3.3: Manufacturer: Broadcom Corp
usb 3-3.3.3: SerialNumber: 0090A286559E
Bluetooth: hci0: BCM: chip id 70
Bluetooth: hci0: BCM (001.001.011) build 0000
bluetooth hci0: firmware: direct-loading firmware brcm/BCM.hcd
Bluetooth: hci0: BCM (001.001.011) build 0154
David Herrmann [Mon, 7 Sep 2015 10:05:41 +0000 (12:05 +0200)]
Bluetooth: hidp: fix device disconnect on idle timeout
The HIDP specs define an idle-timeout which automatically disconnects a
device. This has always been implemented in the HIDP layer and forced a
synchronous shutdown of the hidp-scheduler. This works just fine, but
lacks a forced disconnect on the underlying l2cap channels. This has been
broken since:
The old session-management always forced an l2cap error on the ctrl/intr
channels when shutting down. The new session-management skips this, as we
don't want to enforce channel policy on the caller. In other words, if
user-space removes an HIDP device, the underlying channels (which are
*owned* and *referenced* by user-space) are still left active. User-space
needs to call shutdown(2) or close(2) to release them.
Unfortunately, this does not work with idle-timeouts. There is no way to
signal user-space that the HIDP layer has been stopped. The API simply
does not support any event-passing except for poll(2). Hence, we restore
old behavior and force EUNATCH on the sockets if the HIDP layer is
disconnected due to idle-timeouts (behavior of explicit disconnects
remains unmodified). User-space can still call
getsockopt(..., SO_ERROR, ...)
..to retrieve the EUNATCH error and clear sk_err. Hence, the channels can
still be re-used (which nobody does so far, though). Therefore, the API
still supports the new behavior, but with this patch it's also compatible
to the old implicit channel shutdown.
Cc: <stable@vger.kernel.org> # 3.10+ Reported-by: Mark Haun <haunma@keteu.org> Reported-by: Luiz Augusto von Dentz <luiz.dentz@gmail.com> Signed-off-by: David Herrmann <dh.herrmann@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Marcel Holtmann [Sat, 17 Oct 2015 14:00:28 +0000 (16:00 +0200)]
Bluetooth: btintel: Add diagnostic support for older controllers
For the older controllers like Wilkens Peak and Stone Peak, enabling the
traces requires to switch into manufacturer mode first. This patch does
exactly that, but only for these older controllers.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Marcel Holtmann [Sat, 17 Oct 2015 14:00:26 +0000 (16:00 +0200)]
Bluetooth: Add new quirk for non-persistent diagnostic settings
If the diagnostic settings are not persistent over HCI Reset, then this
quirk can be used to tell the Bluetoth core about it. This will ensure
that the settings are programmed correctly when the controller is
powered up.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Arnd Bergmann [Fri, 16 Oct 2015 22:03:38 +0000 (00:03 +0200)]
Bluetooth: bpa10x: fix BT_HCIUART dependency
The change to bpa10x to use the h4_recv_buf helper added a dependency
on BT_HCIUART. This was incorrectly added to Kconfig by adding a
'select' statement, which now in turn causes build failures
when CONFIG_TTY is not set:
warning: (BT_HCIBPA10X) selects BT_HCIUART which has unmet direct dependencies (NET && BT && TTY)
vers/built-in.o: In function `hci_uart_tty_receive':
fpga-mgr.c:(.text+0x282824): undefined reference to `tty_unthrottle'
drivers/built-in.o: In function `hci_uart_tty_ioctl':
fpga-mgr.c:(.text+0x282aa0): undefined reference to `n_tty_ioctl_helper'
drivers/built-in.o: In function `hci_uart_flush':
This replaces the 'select BT_HCIUART' dependency with 'depends on', which
does not have this kind of problem. Alternatively, one could add 'depends
on TTY', but avoiding 'select' on user-visible options is generally the
preferred choice as that does not introduce the potential for dependency
loops or incomplete dependency chains.
Johan Hedberg [Mon, 12 Oct 2015 11:36:19 +0000 (13:36 +0200)]
Bluetooth: Don't use remote address type to decide IRK persistency
There are LE devices on the market that start off by announcing their
public address and then once paired switch to using private address.
To be interoperable with such devices we should simply trust the fact
that we're receiving an IRK from them to indicate that they may use
private addresses in the future. Instead, simply tie the persistency
to the bonding/no-bonding information the same way as for LTKs and
CSRKs.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Marcel Holtmann [Fri, 9 Oct 2015 14:13:51 +0000 (16:13 +0200)]
Bluetooth: Queue diagnostic messages together with HCI packets
Sending diagnostic messages directly to the monitor socket might cause
issues for devices processing their messages in interrupt context. So
instead of trying to directly forward them, queue them up with the other
HCI packets and lets them be processed by the sockets at the same time.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Marcel Holtmann [Fri, 9 Oct 2015 14:13:49 +0000 (16:13 +0200)]
Bluetooth: Remove quirk for HCI_VENDOR_PKT filter handling
The HCI_VENDOR_PKT quirk was needed for BPA-100/105 devices that send
these messages. Now that there is support for proper diagnostic channel
this quirk is no longer needed.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Marcel Holtmann [Thu, 8 Oct 2015 18:23:08 +0000 (20:23 +0200)]
Bluetooth: btusb: Add support for Broadcom LM_DIAG interface
The Broadcom Bluetooth USB devices have a third interface that is
dedicated for LM_DIAG messages. The If#= 2 describes this interface
and it consists of one bulk in and one bulk endpoint.
For all Broadcom based devices with this interface, the driver now
claims it and schedules URBs for it. This allows to capture the
LM_DIAG messages and allows forwarding them via hci_recv_diag into
the diagnostic channel of the Bluetooth subsystem.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
1) Account for extra headroom in ath9k driver, from Felix Fietkau.
2) Fix OOPS in pppoe driver due to incorrect socket state transition,
from Guillaume Nault.
3) Kill memory leak in amd-xgbe debugfx, from Geliang Tang.
4) Power management fixes for iwlwifi, from Johannes Berg.
5) Fix races in reqsk_queue_unlink(), from Eric Dumazet.
6) Fix dst_entry usage in ARP replies, from Jiri Benc.
7) Cure OOPSes with SO_GET_FILTER, from Daniel Borkmann.
8) Missing allocation failure check in amd-xgbe, from Tom Lendacky.
9) Various resource allocation/freeing cures in DSA< from Neil
Armstrong.
10) A series of bug fixes in the openvswitch conntrack support, from
Joe Stringer.
11) Fix two cases (BPF and act_mirred) where we have to clean the sender
cpu stored in the SKB before transmitting. From WANG Cong and
Alexei Starovoitov.
12) Disable VLAN filtering in promiscuous mode in mlx5 driver, from
Achiad Shochat.
13) Older bnx2x chips cannot do 4-tuple UDP hashing, so prevent this
configuration via ethtool. From Yuval Mintz.
14) Don't call rt6_uncached_list_flush_dev() from rt6_ifdown() when
'dev' is NULL, from Eric Biederman.
15) Prevent stalled link synchronization in tipc, from Jon Paul Maloy.
16) kcalloc() gstrings ethtool buffer before having driver fill it in,
in order to prevent kernel memory leaking. From Joe Perches.
17) Fix mixxing rt6_info initialization for blackhole routes, from
Martin KaFai Lau.
18) Kill VLAN regression in via-rhine, from Andrej Ota.
19) Missing pfmemalloc check in sk_add_backlog(), from Eric Dumazet.
20) Fix spurious MSG_TRUNC signalling in netlink dumps, from Ronen Arad.
21) Scrube SKBs when pushing them between namespaces in openvswitch,
from Joe Stringer.
22) bcmgenet enables link interrupts too early, fix from Florian
Fainelli.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (92 commits)
net: bcmgenet: Fix early link interrupt enabling
tunnels: Don't require remote endpoint or ID during creation.
openvswitch: Scrub skb between namespaces
xen-netback: correctly check failed allocation
net: asix: add support for the Billionton GUSB2AM-1G-B USB adapter
netlink: Trim skb to alloc size to avoid MSG_TRUNC
net: add pfmemalloc check in sk_add_backlog()
via-rhine: fix VLAN receive handling regression.
ipv6: Initialize rt6_info properly in ip6_blackhole_route()
ipv6: Move common init code for rt6_info to a new function rt6_info_init()
Bluetooth: Fix initializing conn_params in scan phase
Bluetooth: Fix conn_params list update in hci_connect_le_scan_cleanup
Bluetooth: Fix remove_device behavior for explicit connects
Bluetooth: Fix LE reconnection logic
Bluetooth: Fix reference counting for LE-scan based connections
Bluetooth: Fix double scan updates
mlxsw: core: Fix race condition in __mlxsw_emad_transmit
tipc: move fragment importance field to new header position
ethtool: Use kcalloc instead of kmalloc for ethtool_get_strings
tipc: eliminate risk of stalled link synchronization
...
Florian Fainelli [Sat, 17 Oct 2015 21:22:46 +0000 (14:22 -0700)]
net: bcmgenet: Fix early link interrupt enabling
Link interrupts are enabled in init_umac(), which is too early for us to
process them since we do not yet have a valid PHY device pointer. On
BCM7425 chips for instance, we will crash calling phy_mac_interrupt()
because phydev is NULL.
Fix this by moving the link interrupts enabling in
bcmgenet_netif_start(), under a specific function:
bcmgenet_link_intr_enable() and while at it, update the comments
surrounding the code.
Fixes: 6cc8e6d4dcb36 ("net: bcmgenet: Delay PHY initialization to bcmgenet_open()") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter/IPVS updates for your net-next
tree. Most relevantly, updates for the nfnetlink_log to integrate with
conntrack, fixes for cttimeout and improvements for nf_queue core, they are:
1) Remove useless ifdef around static inline function in IPVS, from
Eric W. Biederman.
2) Simplify the conntrack support for nfnetlink_queue: Merge
nfnetlink_queue_ct.c file into nfnetlink_queue_core.c, then rename it back
to nfnetlink_queue.c
3) Use y2038 safe timestamp from nfnetlink_queue.
4) Get rid of dead function definition in nf_conntrack, from Flavio
Leitner.
5) Attach conntrack support for nfnetlink_log.c, from Ken-ichirou MATSUZAWA.
This adds a new NETFILTER_NETLINK_GLUE_CT Kconfig switch that
controls enabling both nfqueue and nflog integration with conntrack.
The userspace application can request this via NFULNL_CFG_F_CONNTRACK
configuration flag.
6) Remove unused netns variables in IPVS, from Eric W. Biederman and
Simon Horman.
7) Don't put back the refcount on the cttimeout object from xt_CT on success.
8) Fix crash on cttimeout policy object removal. We have to flush out
the cttimeout extension area of the conntrack not to refer to an unexisting
object that was just removed.
9) Make sure rcu_callback completion before removing nfnetlink_cttimeout
module removal.
10) Fix compilation warning in br_netfilter when no nf_defrag_ipv4 and
nf_defrag_ipv6 are enabled. Patch from Arnd Bergmann.
11) Autoload ctnetlink dependencies when NFULNL_CFG_F_CONNTRACK is
requested. Again from Ken-ichirou MATSUZAWA.
12) Don't use pointer to previous hook when reinjecting traffic via
nf_queue with NF_REPEAT verdict since it may be already gone. This
also avoids a deadloop if the userspace application keeps returning
NF_REPEAT.
13) A bunch of cleanups for netfilter IPv4 and IPv6 code from Ian Morris.
14) Consolidate logger instance existence check in nfulnl_recv_config().
15) Fix broken atomicity when applying configuration updates to logger
instances in nfnetlink_log.
16) Get rid of the .owner attribute in our hook object. We don't need
this anymore since we're dropping pending packets that have escaped
from the kernel when unremoving the hook. Patch from Florian Westphal.
17) Remove unnecessary rcu_read_lock() from nf_reinject code, we always
assume RCU read side lock from .call_rcu in nfnetlink. Also from Florian.
18) Use static inline function instead of macros to define NF_HOOK() and
NF_HOOK_COND() when no netfilter support in on, from Arnd Bergmann.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Sowmini found hang with rds-ping while testing RDS over TCP. Its
a corner case and doesn't happen always. The issue is not reproducible
with IB transport. Its clear from below dump why we see it with RDS TCP.
This happens because rds_send_xmit() chain wants to take
sock_lock which is already taken by tcp_v4_rcv() on its
way to rds_tcp_data_ready(). Commit db6526dcb51b ("RDS: use
rds_send_xmit() state instead of RDS_LL_SEND_FULL") which
was trying to opportunistically finish the send request
in same thread context.
But because of above recursive lock hang with RDS TCP,
the send work from rds_send_pong() needs to deferred to
worker to avoid lock up. Given RDS ping is more of connectivity
test than performance critical path, its should be ok even
for transport like IB.
Reported-by: Sowmini Varadhan <sowmini.varadhan@oracle.com> Acked-by: Sowmini Varadhan <sowmini.varadhan@oracle.com> Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org> Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Acked-by: Sowmini Varadhan <sowmini.varadhan@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jesse Gross [Fri, 16 Oct 2015 23:36:00 +0000 (16:36 -0700)]
tunnels: Don't require remote endpoint or ID during creation.
Before lightweight tunnels existed, it really didn't make sense to
create a tunnel that was not fully specified, such as without a
destination IP address - the resulting packets would go nowhere.
However, with lightweight tunnels, the opposite is true - it doesn't
make sense to require this information when it will be provided later
on by the route. This loosens the requirements for this information.
An alternative would be to allow the relaxed version only when
COLLECT_METADATA is enabled. However, since there are several
variations on this theme (such as NBMA tunnels in GRE), just dropping
the restrictions seems the most consistent across tunnels and with
the existing configuration.
CC: John Linville <linville@tuxdriver.com> Signed-off-by: Jesse Gross <jesse@nicira.com> Signed-off-by: Thomas Graf <tgraf@suug.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing rule to export mpls iptunnel header needed by iproute2
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org> Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Stringer [Fri, 16 Oct 2015 18:08:18 +0000 (11:08 -0700)]
openvswitch: Scrub skb between namespaces
If OVS receives a packet from another namespace, then the packet should
be scrubbed. However, people have already begun to rely on the behaviour
that skb->mark is preserved across namespaces, so retain this one field.
This is mainly to address information leakage between namespaces when
using OVS internal ports, but by placing it in ovs_vport_receive() it is
more generally applicable, meaning it should not be overlooked if other
port types are allowed to be moved into namespaces in future.
Signed-off-by: Joe Stringer <joestringer@nicira.com> Acked-by: Pravin B Shelar <pshelar@nicira.com> Acked-by: Thomas Graf <tgraf@suug.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 19 Oct 2015 05:23:33 +0000 (22:23 -0700)]
Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth
Johan Hedberg says:
====================
pull request: bluetooth 2015-10-16
First of all, sorry for the late set of patches for the 4.3 cycle. We
just finished an intensive week of testing at the Bluetooth UnPlugFest
and discovered (and fixed) issues there. Unfortunately a few issues
affect 4.3-rc5 in a way that they break existing Bluetooth LE mouse and
keyboard support.
The regressions result from supporting LE privacy in conjunction with
scanning for Resolvable Private Addresses before connecting. A feature
that has been tested heavily (including automated unit tests), but sadly
some regressions slipped in. The UnPlugFest with its multitude of test
platforms is a good battle testing ground for uncovering every corner
case.
The patches in this pull request focus only on fixing the regressions in
4.3-rc5. The patches look a bit larger since we also added comments in
the critical sections of the fixes to improve clarity.
I would appreciate if we can get these regression fixes to Linus
quickly. Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Fri, 16 Oct 2015 10:00:51 +0000 (12:00 +0200)]
net: hix5hd2_gmac: avoid integer overload warning
BITS_RX_EN is an 'unsigned long' constant, so the ones complement of that
has bits set that do not fit into a 32-bit variable on 64-bit architectures,
which causes a harmless gcc warning:
drivers/net/ethernet/hisilicon/hix5hd2_gmac.c: In function 'hix5hd2_port_disable':
drivers/net/ethernet/hisilicon/hix5hd2_gmac.c:374:2: warning: large integer implicitly truncated to unsigned type [-Woverflow]
writel_relaxed(~(BITS_RX_EN | BITS_TX_EN), priv->base + PORT_EN);
This adds a cast to (u32) to tell gcc that the code is indeed fine.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Fri, 16 Oct 2015 09:33:49 +0000 (11:33 +0200)]
net: hisilicon: add OF dependency
The HNS MDIO driver fails to build on older ARM machines that are not
yet converted to CONFIG_OF:
drivers/net/ethernet/hisilicon/hns_mdio.c: In function 'hns_mdio_bus_name':
drivers/net/ethernet/hisilicon/hns_mdio.c:405:14: error: 'OF_BAD_ADDR' undeclared (first use in this function)
u64 taddr = OF_BAD_ADDR;
^
drivers/net/ethernet/hisilicon/hns_mdio.c:405:14: note: each undeclared identifier is reported only once for each function it appears in
drivers/net/ethernet/hisilicon/hns_mdio.c:409:11: error: implicit declaration of function 'of_translate_address' [-Werror=implicit-function-declaration]
taddr = of_translate_address(np, addr);
^
This clarifies the dependency to ensure we don't attempt to build these
drivers without CONFIG_OF, but also adds a COMPILE_TEST alternative to
give us better build coverage testing.
Build-tested on x86 as well to ensure this actually works.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Fri, 16 Oct 2015 09:30:56 +0000 (11:30 +0200)]
net: hisilicon: include linux/vmalloc.h in dsaf
Some configurations fail to build the hns dsaf code because of
a missing header file:
ethernet/hisilicon/hns/hns_dsaf_main.c: In function 'hns_dsaf_init':
ethernet/hisilicon/hns/hns_dsaf_main.c:1096:2: error: implicit declaration of function 'vzalloc' [-Werror=implicit-function-declaration]
priv->soft_mac_tbl = vzalloc(sizeof(*priv->soft_mac_tbl)
This adds the correct #include.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 19 Oct 2015 02:57:12 +0000 (19:57 -0700)]
Merge branch 'hns-fixes'
yankejian says:
====================
net: hns: fixes two bugs in hns driver
This patchset fixes two bugs in hns driver.
- fixes timeout when received pause frame from the connective ports
- should be set by using ethtool -s when the devices are link down
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
lisheng [Fri, 16 Oct 2015 09:03:20 +0000 (17:03 +0800)]
net: hns: fixes a bug about timeout by pause frame
this patch fixes the bug triggered timeout sequence. when the connective
ports cannot accept the packets with higher speed, they will send out the
pause frame to the Soc's mac. At that time, the driver resets the relevant
of the Soc, then it causes the packets cannot be sent out immediately.
this patch fixes the issue.
Signed-off-by: yankejian <yankejian@huawei.com> Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com> Signed-off-by: lisheng <lisheng011@huawei.com> Signed-off-by: lipeng <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Chenny Xu [Fri, 16 Oct 2015 09:03:19 +0000 (17:03 +0800)]
net: hns: fixes the issue by using ethtool -s
before this patch, hns driver only permits user to set the net device
by using ethtool -s when the device is link up. it is obviously not so
good. it needs to be set no matter it is link up or down. so this patch
fixes this issue.
Signed-off-by: yankejian <yankejian@huawei.com> Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com> Signed-off-by: lisheng <lisheng011@huawei.com> Signed-off-by: lipeng <lipeng321@huawei.com> Signed-off-by: Chenny Xu <chenny.xu@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 19 Oct 2015 02:54:45 +0000 (19:54 -0700)]
Merge branch 'hsi-fixes'
huangdaode says:
====================
net: hisilicon fix some bugs in HNS drivers
This patchset fixes the two bugs in HNS driver, one is remove the hnae sysfs interface
according to the review comments from Arnd Bergmann <arnd@arndb.de>, another
is fixing the wrong mac_id judgement bug which is found during internal tests.
change log:
v3:
remove the hnae sysfs interface.
v2:
1) remove first bug fix, which is fixed in another patch submitted by
Arnd Bergmann <arnd@arndb.de>
2) change the code sytyle according to Joe.
v1:
initial version.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
huangdaode [Fri, 16 Oct 2015 03:54:17 +0000 (11:54 +0800)]
net: hisilicon fix a bug on Hisilicon Network Subsystem
This patch fixes the wrong judgement of mac_id when get port num.
Signed-off-by: huangdaode <huangdaode@hisilicon.com> Signed-off-by: yankejian <yankejian@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The 'bcm-phy-lib.c', added as a part of the commit
"net: phy: Add Broadcom phy library for common interfaces"
was missing the module license. This was causing an issue
when the library is built as a module; "module license
'unspecified' taints kernel".
This patch fixes the issue by adding the module license,
author and description to the bcm-phy-lib.c file.
Fixes: a1cba5613edf5 ("net: phy: Add Broadcom phy library for
common interfaces") Signed-off-by: Arun Parameswaran <arunp@broadcom.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Arad, Ronen [Thu, 15 Oct 2015 08:55:17 +0000 (01:55 -0700)]
netlink: Trim skb to alloc size to avoid MSG_TRUNC
netlink_dump() allocates skb based on the calculated min_dump_alloc or
a per socket max_recvmsg_len.
min_alloc_size is maximum space required for any single netdev
attributes as calculated by rtnl_calcit().
max_recvmsg_len tracks the user provided buffer to netlink_recvmsg.
It is capped at 16KiB.
The intention is to avoid small allocations and to minimize the number
of calls required to obtain dump information for all net devices.
netlink_dump packs as many small messages as could fit within an skb
that was sized for the largest single netdev information. The actual
space available within an skb is larger than what is requested. It could
be much larger and up to near 2x with align to next power of 2 approach.
Allowing netlink_dump to use all the space available within the
allocated skb increases the buffer size a user has to provide to avoid
truncaion (i.e. MSG_TRUNG flag set).
It was observed that with many VLANs configured on at least one netdev,
a larger buffer of near 64KiB was necessary to avoid "Message truncated"
error in "ip link" or "bridge [-c[ompressvlans]] vlan show" when
min_alloc_size was only little over 32KiB.
This patch trims skb to allocated size in order to allow the user to
avoid truncation with more reasonable buffer size.
Signed-off-by: Ronen Arad <ronen.arad@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Li RongQing [Thu, 15 Oct 2015 08:54:36 +0000 (16:54 +0800)]
ipconfig: send Client-identifier in DHCP requests
A dhcp server may provide parameters to a client from a pool of IP
addresses and using a shared rootfs, or provide a specific set of
parameters for a specific client, usually using the MAC address to
identify each client individually. The dhcp protocol also specifies
a client-id field which can be used to determine the correct
parameters to supply when no MAC address is available. There is
currently no way to tell the kernel to supply a specific client-id,
only the userspace dhcp clients support this feature, but this can
not be used when the network is needed before userspace is available
such as when the root filesystem is on NFS.
This patch is to be able to do something like "ip=dhcp,client_id_type,
client_id_value", as a kernel parameter to enable the kernel to
identify itself to the server.
Signed-off-by: Li RongQing <roy.qing.li@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 18 Oct 2015 19:07:48 +0000 (12:07 -0700)]
Merge branch 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Here are some bugfixes for the I2C subsystem.
Kieran found a flaw in the recently renewed wake irq handling. Mika
handled a user bug report where the ACPI info turned out to be
unusable. I updated MAINTAINERS so that such bug reports will sooner
get to the right people. Geert pointed me to a problem of some i2c
drivers regarding PM which I fixed"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: designware: Do not use parameters from ACPI on Dell Inspiron 7348
MAINTAINERS: add maintainers for Synopsis Designware I2C drivers
i2c: designware-platdrv: enable RuntimePM before registering to the core
i2c: s3c2410: enable RuntimePM before registering to the core
i2c: rcar: enable RuntimePM before registering to the core
i2c: return probe deferred status on dev_pm_domain_attach
Mika Westerberg [Thu, 24 Sep 2015 09:06:54 +0000 (12:06 +0300)]
i2c: designware: Do not use parameters from ACPI on Dell Inspiron 7348
ACPI SSCN/FMCN methods were originally added because then the platform can
provide the most accurate HCNT/LCNT values to the driver. However, this
seems not to be true for Dell Inspiron 7348 where using these causes the
touchpad to fail in boot:
i2c_hid i2c-DLL0675:00: failed to retrieve report from device.
i2c_designware INT3433:00: i2c_dw_handle_tx_abort: lost arbitration
i2c_hid i2c-DLL0675:00: failed to retrieve report from device.
i2c_designware INT3433:00: controller timed out
The values received from ACPI are (in fast mode):
HCNT: 72
LCNT: 160
this translates to following timings (input clock is 100MHz on Broadwell):
tHIGH: 720 ns (spec min 600 ns)
tLOW: 1600 ns (spec min 1300 ns)
Bus period: 2920 ns (assuming 300 ns tf and tr)
Bus speed: 342.5 kHz
Both tHIGH and tLOW are within the I2C specification.
The calculated values when ACPI parameters are not used are (in fast mode):
HCNT: 87
LCNT: 159
which translates to:
tHIGH: 870 ns (spec min 600 ns)
tLOW: 1590 ns (spec min 1300 ns)
Bus period 3060 ns (assuming 300 ns tf and tr)
Bus speed 326.8 kHz
These values are also within the I2C specification.
Since both ACPI and calculated values meet the I2C specification timing
requirements it is hard to say why the touchpad does not function properly
with the ACPI values except that the bus speed is higher in this case (but
still well below the max 400kHz).
Solve this by adding DMI quirk to the driver that disables using ACPI
parameters on this particulare machine.
Reported-by: Pavel Roskin <plroskin@gmail.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Tested-by: Pavel Roskin <plroskin@gmail.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Cc: stable@kernel.org
Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next
This merge resolves conflicts with 75aec9df3a78 ("bridge: Remove
br_nf_push_frag_xmit_sk") as part of Eric Biederman's effort to improve
netns support in the network stack that reached upstream via David's
net-next tree.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Conflicts:
net/bridge/br_netfilter_hooks.c
Eric Dumazet [Wed, 30 Sep 2015 01:52:25 +0000 (18:52 -0700)]
net: add pfmemalloc check in sk_add_backlog()
Greg reported crashes hitting the following check in __sk_backlog_rcv()
BUG_ON(!sock_flag(sk, SOCK_MEMALLOC));
The pfmemalloc bit is currently checked in sk_filter().
This works correctly for TCP, because sk_filter() is ran in
tcp_v[46]_rcv() before hitting the prequeue or backlog checks.
For UDP or other protocols, this does not work, because the sk_filter()
is ran from sock_queue_rcv_skb(), which might be called _after_ backlog
queuing if socket is owned by user by the time packet is processed by
softirq handler.
Fixes: b4b9e35585089 ("netvm: set PF_MEMALLOC as appropriate during SKB processing") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Greg Thelen <gthelen@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 17 Oct 2015 00:39:27 +0000 (17:39 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
"Just two small fixups to ads7846 touchscreen controller driver and
Cypress touchpad driver"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: cyapa - fix the copy paste error on electrodes_rx value
Input: ads7846 - correct the value got from SPI
Linus Torvalds [Sat, 17 Oct 2015 00:11:14 +0000 (17:11 -0700)]
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fix from Stephen Boyd:
"Just one revert for Armada XP devices: the conversion to
of_clk_get_parent_name() wasn't a direct translation, so we
revert back to of_clk_get() + __clk_get_name().
We could make of_clk_get_parent_name() more robust, but that
may have unintended side-effects, so we'll do that in the
next version"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
Partially revert "clk: mvebu: Convert to clk_hw based provider APIs"
Linus Torvalds [Fri, 16 Oct 2015 20:03:05 +0000 (13:03 -0700)]
Merge tag 'dm-4.3-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
"Two DM target error path cleanup fixes (one for stable in DM thinp and
one for a v4.3-rc5 thinko in DM snapshot)"
* tag 'dm-4.3-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm thin: fix missing pool reference count decrement in pool_ctr error path
dm snapshot persistent: fix missing cleanup in persistent_ctr error path
Linus Torvalds [Fri, 16 Oct 2015 19:55:34 +0000 (12:55 -0700)]
Merge branch 'for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"I have two more bug fixes for btrfs.
My commit fixes a bug we hit last week at FB, a combination of lots of
hard links and an admin command to resolve inode numbers.
Dave is adding checks to make sure balance on current kernels ignores
filters it doesn't understand. The penalty for being wrong is just
doing more work (not crashing etc), but it's a good fix"
* 'for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
btrfs: fix use after free iterating extrefs
btrfs: check unsupported filters in balance arguments
Linus Torvalds [Fri, 16 Oct 2015 19:47:02 +0000 (12:47 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
Pull Ceph fixes from Sage Weil:
"Just two small items from Ilya:
The first patch fixes the RBD readahead to grab full objects. The
second fixes the write ops to prevent undue promotion when a cache
tier is configured on the server side"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
rbd: use writefull op for object size writes
rbd: set max_sectors explicitly
Linus Torvalds [Fri, 16 Oct 2015 19:25:54 +0000 (12:25 -0700)]
Merge tag 'pm+acpi-4.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"These fix two recent regressions (ACPICA, the generic power domains
framework) and one crash that may happen on specific hardware
supported since 4.1 (intel_pstate).
Specifics:
- Fix a regression introduced by a recent ACPICA cleanup that
uncovered a latent bug (Lv Zheng).
- Fix a recent regression in the generic power domains framework that
may cause it to violate PM QoS latency constraints in some cases
(Ulf Hansson).
- Fix an intel_pstate driver crash on the Knights Landing chips that
do not update the MPERF counter as often as expected by the driver
which may result in a divide by 0 (Srinivas Pandruvada)"
* tag 'pm+acpi-4.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: intel_pstate: Fix divide by zero on Knights Landing (KNL)
ACPICA: Tables: Fix FADT dependency regression
PM / Domains: Fix validation of latency constraints in genpd governor
Linus Torvalds [Fri, 16 Oct 2015 19:19:11 +0000 (12:19 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Nothing too crazy or exciting:
- two MAINTAINERS entries that I didn't see the point in delaying.
- one drm mst fix to stop sending uninitialised data to monitors
- two amdgpu fixes
- one radeon mst tiling fix
- one vmwgfx regression fix
- one virtio warning fix.
I have found one locking problem that needs a bit of reorg to fix, but
I'm not sure it's worth putting in -fixes as I don't think we've seen
it hit in the real world ever, I just found it using the virtio-gpu
driver when working on it. I'll possibly send it next week once I've
time to discuss with Daniel"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/virtio: use %llu format string form atomic64_t
MAINTAINERS: Add myself as maintainer for the gma500 driver
MAINTAINERS: add a maintainer for the atmel-hlcdc DRM driver
drm/amdgpu: Keep the pflip interrupts always enabled v7
drm/amdgpu: adjust default dispclk (v2)
drm/dp/mst: make mst i2c transfer code more robust.
drm/radeon: attach tile property to mst connector
drm/vmwgfx: Fix kernel NULL pointer dereference on older hardware
Linus Torvalds [Fri, 16 Oct 2015 19:07:43 +0000 (12:07 -0700)]
Merge tag 'powerpc-4.3-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Re-enable CONFIG_SCSI_DH in our defconfigs
- Remove unused os_area_db_id_video_mode
- cxl: fix leak of IRQ names in cxl_free_afu_irqs() from Andrew
- cxl: fix leak of ctx->irq_bitmap when releasing context via kernel API from Andrew
- cxl: fix leak of ctx->mapping when releasing kernel API contexts from Andrew
- cxl: Workaround malformed pcie packets on some cards from Philippe
- cxl: Fix number of allocated pages in SPA from Christophe Lombard
- Fix checkstop in native_hpte_clear() with lockdep from Cyril
- Panic on unhandled Machine Check on powernv from Daniel
- selftests/powerpc: Fix build failure of load_unaligned_zeropad test
* tag 'powerpc-4.3-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
selftests/powerpc: Fix build failure of load_unaligned_zeropad test
powerpc/powernv: Panic on unhandled Machine Check
powerpc: Fix checkstop in native_hpte_clear() with lockdep
cxl: Fix number of allocated pages in SPA
cxl: Workaround malformed pcie packets on some cards
cxl: fix leak of ctx->mapping when releasing kernel API contexts
cxl: fix leak of ctx->irq_bitmap when releasing context via kernel API
cxl: fix leak of IRQ names in cxl_free_afu_irqs()
powerpc/ps3: Remove unused os_area_db_id_video_mode
powerpc/configs: Re-enable CONFIG_SCSI_DH
Linus Torvalds [Fri, 16 Oct 2015 18:42:37 +0000 (11:42 -0700)]
Merge branch 'akpm' (patches from Andrew)
Merge misc fixes from Andrew Morton:
"6 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
sh: add copy_user_page() alias for __copy_user()
lib/Kconfig: ZLIB_DEFLATE must select BITREVERSE
mm, dax: fix DAX deadlocks
memcg: convert threshold to bytes
builddeb: remove debian/files before build
mm, fs: obey gfp_mapping for add_to_page_cache()
Andrew Morton [Thu, 15 Oct 2015 22:28:35 +0000 (15:28 -0700)]
lib/Kconfig: ZLIB_DEFLATE must select BITREVERSE
lib/built-in.o: In function `__bitrev32':
deftree.c:(.text+0x1e799): undefined reference to `byte_rev_table'
deftree.c:(.text+0x1e7a0): undefined reference to `byte_rev_table'
deftree.c:(.text+0x1e7b4): undefined reference to `byte_rev_table'
deftree.c:(.text+0x1e7c1): undefined reference to `byte_rev_table'
Anything which uses bitrevX() has to select BITREVERSE, to grab
lib/bitrev.o.
Reported-by: Jim Davis <jim.epost@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ross Zwisler [Thu, 15 Oct 2015 22:28:32 +0000 (15:28 -0700)]
mm, dax: fix DAX deadlocks
The following two locking commits in the DAX code:
commit 843172978bb9 ("dax: fix race between simultaneous faults")
commit 46c043ede471 ("mm: take i_mmap_lock in unmap_mapping_range() for DAX")
introduced a number of deadlocks and other issues which need to be fixed
for the v4.3 kernel. The list of issues in DAX after these commits
(some newly introduced by the commits, some preexisting) can be found
here:
https://lkml.org/lkml/2015/9/25/602 (Subject: "Re: [PATCH] dax: fix deadlock in __dax_fault").
This undoes most of the changes introduced by those two commits,
essentially returning us to the DAX locking scheme that was used in
v4.2.
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Dan Williams <dan.j.williams@intel.com> Tested-by: Dave Chinner <dchinner@redhat.com> Cc: Jan Kara <jack@suse.com> Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com> Cc: Matthew Wilcox <matthew.r.wilcox@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Riku Voipio [Thu, 15 Oct 2015 22:28:26 +0000 (15:28 -0700)]
builddeb: remove debian/files before build
Commit 3716001bcb7f ("deb-pkg: add source package") added the ability to
create a debian changelog file. This exposed that previously the
builddeb script hasn't cleared debian/files between builds.
As debian/files keeps accumulating entries, the changes file will end up
growing indefinelty. With outdated entries in debian/files, builddeb
script will exit with failure. This regression impacts those who use
"make deb-pkg" target to build kernel into a .deb package and never use
"make mrproper" or other means to clean kernel tree from generated
directories.
To fix the regression, remove debian/files before starting build and in
the generated clean rule.
Fixes: 3716001bcb7f ("deb-pkg: add source package") Signed-off-by: Riku Voipio <riku.voipio@linaro.org> Reported-by: Doug Smythies <dsmythies@telus.net> Tested-by: Doug Smythies <dsmythies@telus.net> Tested-by: Kalle Valo <kvalo@codeaurora.org> Acked-by: Ben Hutchings <ben@decadent.org.uk> Cc: Michal Marek <mmarek@suse.cz> Cc: maximilian attems <maks@stro.at> Cc: Chris J Arges <chris.j.arges@canonical.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michal Hocko [Thu, 15 Oct 2015 22:28:24 +0000 (15:28 -0700)]
mm, fs: obey gfp_mapping for add_to_page_cache()
Commit 6afdb859b710 ("mm: do not ignore mapping_gfp_mask in page cache
allocation paths") has caught some users of hardcoded GFP_KERNEL used in
the page cache allocation paths. This, however, wasn't complete and
there were others which went unnoticed.
Dave Chinner has reported the following deadlock for xfs on loop device:
: With the recent merge of the loop device changes, I'm now seeing
: XFS deadlock on my single CPU, 1GB RAM VM running xfs/073.
:
: The deadlocked is as follows:
:
: kloopd1: loop_queue_read_work
: xfs_file_iter_read
: lock XFS inode XFS_IOLOCK_SHARED (on image file)
: page cache read (GFP_KERNEL)
: radix tree alloc
: memory reclaim
: reclaim XFS inodes
: log force to unpin inodes
: <wait for log IO completion>
:
: xfs-cil/loop1: <does log force IO work>
: xlog_cil_push
: xlog_write
: <loop issuing log writes>
: xlog_state_get_iclog_space()
: <blocks due to all log buffers under write io>
: <waits for IO completion>
:
: kloopd1: loop_queue_write_work
: xfs_file_write_iter
: lock XFS inode XFS_IOLOCK_EXCL (on image file)
: <wait for inode to be unlocked>
:
: i.e. the kloopd, with it's split read and write work queues, has
: introduced a dependency through memory reclaim. i.e. that writes
: need to be able to progress for reads make progress.
:
: The problem, fundamentally, is that mpage_readpages() does a
: GFP_KERNEL allocation, rather than paying attention to the inode's
: mapping gfp mask, which is set to GFP_NOFS.
:
: The didn't used to happen, because the loop device used to issue
: reads through the splice path and that does:
:
: error = add_to_page_cache_lru(page, mapping, index,
: GFP_KERNEL & mapping_gfp_mask(mapping));
This has changed by commit aa4d86163e4 ("block: loop: switch to VFS
ITER_BVEC").
This patch changes mpage_readpage{s} to follow gfp mask set for the
mapping. There are, however, other places which are doing basically the
same.
lustre:ll_dir_filler is doing GFP_KERNEL from the function which
apparently uses GFP_NOFS for other allocations so let's make this
consistent.
cifs:readpages_get_pages is called from cifs_readpages and
__cifs_readpages_from_fscache called from the same path obeys mapping
gfp.
ramfs_nommu_expand_for_mapping is hardcoding GFP_KERNEL as well
regardless it uses mapping_gfp_mask for the page allocation.
ext4_mpage_readpages is the called from the page cache allocation path
same as read_pages and read_cache_pages
As I've noticed in my previous post I cannot say I would be happy about
sprinkling mapping_gfp_mask all over the place and it sounds like we
should drop gfp_mask argument altogether and use it internally in
__add_to_page_cache_locked that would require all the filesystems to use
mapping gfp consistently which I am not sure is the case here. From a
quick glance it seems that some file system use it all the time while
others are selective.
Signed-off-by: Michal Hocko <mhocko@suse.com> Reported-by: Dave Chinner <david@fromorbit.com> Cc: "Theodore Ts'o" <tytso@mit.edu> Cc: Ming Lei <ming.lei@canonical.com> Cc: Andreas Dilger <andreas.dilger@intel.com> Cc: Oleg Drokin <oleg.drokin@intel.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Arnd Bergmann [Fri, 9 Oct 2015 18:45:42 +0000 (20:45 +0200)]
netfilter: turn NF_HOOK into an inline function
A recent change to the dst_output handling caused a new warning
when the call to NF_HOOK() is the only used of a local variable
passed as 'dev', and CONFIG_NETFILTER is disabled:
net/ipv6/ip6_output.c: In function 'ip6_output':
net/ipv6/ip6_output.c:135:21: warning: unused variable 'dev' [-Wunused-variable]
The reason for this is that the NF_HOOK macro in this case does
not reference the variable at all, and the call to dev_net(dev)
got removed from the ip6_output function. To avoid that warning now
and in the future, this changes the macro into an equivalent
inline function, which tells the compiler that the variable is
passed correctly but still unused.
The dn_forward function apparently had the same problem in
the past and added a local workaround that no longer works
with the inline function. In order to avoid a regression, we
have to also remove the #ifdef from decnet in the same patch.
Fixes: ede2059dbaf9 ("dst: Pass net into dst->output") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Ilya Dryomov [Wed, 7 Oct 2015 15:27:17 +0000 (17:27 +0200)]
rbd: use writefull op for object size writes
This covers only the simplest case - an object size sized write, but
it's still useful in tiering setups when EC is used for the base tier
as writefull op can be proxied, saving an object promotion.
Even though updating ceph_osdc_new_request() to allow writefull should
just be a matter of fixing an assert, I didn't do it because its only
user is cephfs. All other sites were updated.
Ilya Dryomov [Wed, 7 Oct 2015 14:09:35 +0000 (16:09 +0200)]
rbd: set max_sectors explicitly
Commit 30e2bc08b2bb ("Revert "block: remove artifical max_hw_sectors
cap"") restored a clamp on max_sectors. It's now 2560 sectors instead
of 1024, but it's not good enough: we set max_hw_sectors to rbd object
size because we don't want object sized I/Os to be split, and the
default object size is 4M.
So, set max_sectors to max_hw_sectors in rbd at queue init time.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Reviewed-by: Alex Elder <elder@linaro.org>
David S. Miller [Fri, 16 Oct 2015 14:15:31 +0000 (07:15 -0700)]
Merge branch 'mlxsw-spectrum'
Jiri Pirko says:
====================
mlxsw: Driver update, add initial support for Spectrum ASIC
Purpose of this patchset is to introduce initial support for Mellanox
Spectrum ASIC, including L2 bridge forwarding offload.
The only non-mlxsw patch in this patchset is the first one, introducing
pre-change upper notifier. That is used in last patch to ensure ports of
single ASIC are not bridged into multiple bridges, as that scenario is
currently not supported by driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Fri, 16 Oct 2015 12:01:37 +0000 (14:01 +0200)]
mlxsw: spectrum: Add initial support for Spectrum ASIC
Add support for new generation Mellanox Spectrum ASIC, 10/25/40/50 and
100Gb/s Ethernet Switch.
The initial driver implements bridge forwarding offload including
bridge internal VLAN support, FDB static entries, FDB learning and
HW ageing including their setup.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Elad Raz <eladr@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Fri, 16 Oct 2015 12:01:36 +0000 (14:01 +0200)]
mlxsw: reg: Add Switch Port VLAN MAC Learning register definition
Since we currently do not support the offloading of 802.1D bridges, we
need to be able to let the device know it should not learn MAC addresses
on specific {Port, VID} pairs.
Add the SPVMLR register, which controls the learning enablement of
{Port, VID} pairs.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Fri, 16 Oct 2015 12:01:25 +0000 (14:01 +0200)]
mlxsw: cmd: Introduce FID-offset flooding tables
Packets destined to offloaded netdevs will be classified to FIDs in the
device and flooded in case of BUM.
The flooding table used is of type FID-offset, which allows one to
create different flooding domains for different FIDs and specify the
offset in the flooding table for each FID (not necessarily equal to FID
or VID).
Add support for this flooding table type, by exposing the configuration
of the number of tables from this type and their size.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Fri, 16 Oct 2015 12:01:24 +0000 (14:01 +0200)]
mlxsw: cmd: Introduce per-FID flooding tables
In the newly introduced Spectrum switch ASIC, packets destined to not
offloaded netdevs will be classified to special FIDs (vFIDs) in the
device and flooded to the CPU port.
The flooding table used is of type per-FID, which allows one to create
different flooding domains for different vFIDs.
While using a simple single-entry flood table is certainly sufficient at
this point, we do plan to offload 802.1D bridges involving VLAN
interfaces, thus making this change necessary.
Add support for this flooding table type, by exposing the configuration
of the number of tables from this type and their size.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Fri, 16 Oct 2015 12:01:22 +0000 (14:01 +0200)]
net: introduce pre-change upper device notifier
This newly introduced netdevice notifier is called before actual change
upper happens. That provides a possibility for notifier handlers to
know upper change will happen and react to it, including possibility to
forbid the change. That is valuable for drivers which can check if the
upper device linkage is supported and forbid that in case it is not.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Gleixner [Fri, 16 Oct 2015 13:50:22 +0000 (15:50 +0200)]
timekeeping: Increment clock_was_set_seq in timekeeping_init()
timekeeping_init() can set the wall time offset, so we need to
increment the clock_was_set_seq counter. That way hrtimers will pick
up the early offset immediately. Otherwise on a machine which does not
set wall time later in the boot process the hrtimer offset is stale at
0 and wall time timers are going to expire with a delay of 45 years.
Fixes: 868a3e915f7f "hrtimer: Make offset update smarter" Reported-and-tested-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Stefan Liebler <stli@linux.vnet.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: John Stultz <john.stultz@linaro.org>
David S. Miller [Fri, 16 Oct 2015 13:41:10 +0000 (06:41 -0700)]
Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-10-16
This series contains updates to e1000, e1000e, igb, igbvf, ixgbe, ixgbevf,
i40e, i40evf and fm10k.
Alex Duyck fixes the polling routine for i40e/i40evf were the NAPI budget
for receive cleanup was being rounded up to 1 but the netpoll call was
expecting no Rx to be processed as the budget passed was 0. Also cleaned
up IN_NETPOLL flag that was not adding any value due to the receive
cleanup was handled in NAPI. Added support for netpoll for i40evf as
well.
Jesse updates all of our drivers to use napi_complete_done() instead of
napi_complete(), which allows us to use
/sys/class/net/ethX/gro_flush_timeout. Added ethtool support to control
and report the new Interrupt Limit register, since the XL710 hardware
has a different interrupt moderation design that can support a limit of
total interrupts per second per vector.
Shannon cleans up startup log entries to cut down the number by putting
a couple behind debug flags and combining others into single line. Added
support to enable/disable printing VEB statistics via ethtool.
Jingjing fixes a compile issue by adding const to functions that return
strings that are not going to be modified.
Greg Rose cleans up defines that were not used and were causing customer
confusion.
Greg Bowers adds support for setting a new bit in the Set Local LLDP MIB
admin queue command Type field.
Mitch fixes an issue where vlan_features field was set to the same value
as netdev features field, but before the features were actually being
set up, leaving the vlan_features empty. Resolve the issue by setting
up the netdev features first, then mask out the VLAN feature bits when
assigning vlan_features. Fixed VF init timing, where in some instances
the VFs would fail to initialize the first time you loaded the driver.
To correct this, increased the delay time for the init task and wait
longer before giving up.
v2: fix missing space in function header comment in patch 3, based on
feedback from Sergei Shtylyov.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Mitch Williams [Mon, 28 Sep 2015 18:12:43 +0000 (14:12 -0400)]
i40e: increase AQ work limit
With 64 VFs, we can easily overwhelm the AQ on the PF if we have too low
a limit on the number of AQ requests. This leads to ARQ overflow errors,
and occasionally VFs that fail to initialize.
Since we really only hit this condition on initial VF driver load, the
requests that we process are lightweight, so this extra work doesn't
cause problems for the PF driver.
Change-ID: I620221520d8af987df6ace9ba938ffaf22107681 Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mitch Williams [Mon, 28 Sep 2015 18:12:42 +0000 (14:12 -0400)]
i40evf: relax and stagger init timing a bit
On some devices, in some systems, in some configurations, the VFs would
fail to initialize the first time you loaded the driver.
To correct this, increase the delay time for the init task slightly, and
wait longer before giving up.
If we enable VFs and load the VF driver in the same kernel as the PF
driver, we can totally overwhelm the PF driver with AQ requests because
all of the instances try to initialize at the same time.
To help alleviate this, stagger the initial scheduling of the init task
using the PCIe function as a multiplier. We mask off the function to
only three bits so no instance has to wait too long.
With these two changes, initializing 128 VFs on a single device goes
from four minutes to just a few seconds.
Change-ID: If3d8720c1c4e838ab36d8781d9ec295a62380936 Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
projects / mirror_ubuntu-bionic-kernel.git / log