mlxsw: pci: Add support for getting resource through devlink
Up until now the KVD partition was static. This patch introduces the
ability to get the resource sizes via devlink. In case the resource is not
available the default configuration is used.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw: spectrum: Add support for getting kvdl occupancy
Add support for getting the kvdl occupancy through the resource interface.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw: spectrum_dpipe: Connect dpipe tables to resources
Connect current dpipe tables to resources. The tables are connected
in the following fashion:
1. IPv4 host -> KVD hash single
2. IPv6 host -> KVD hash double
3. Adjacency -> KVD linear
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw: spectrum: Register KVD resources with devlink
Register the KVD resources with devlink. The KVD is a memory resource
which is subdivided into three partitions which are the linear, hash
single and hash double.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This is a preparation stage before introducing hot reload. During the
reload process the ASIC should be resetted by accessing the PCI BAR due
to unavailability of the mailbox/emad interfaces.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware processes which are modeled via dpipe commonly use some
internal hardware resources. Such relation can improve the understanding
of hardware limitations. The number of resource's unit consumed per
table's entry are also provided for each table.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for hardware resource abstraction over devlink. Each resource
is identified via id, furthermore it contains information regarding its
size and its related sub resources. Each resource can also provide its
current occupancy.
In some cases the sizes of some resources can be changed, yet for those
changes to take place a hot driver reload may be needed. The reload
capability will be introduced in the next patch.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This is a preparation before introducing resources and hot reload support.
Currently there are two global lock where one protects all devlink access,
and the second one protects devlink port access. This patch adds per devlink
instance lock which protects the internal members which are the sb/dpipe/
resource/ports. By introducing this lock the global devlink port lock can
be discarded.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
this is a pull request of 7 patches for net-next/master.
All patches are by me. Patch 6 is for the "can_raw" protocol and add
error checking to the bind() function. All other patches clean up the
coding style and remove unused parameters in various CAN drivers and
infrastructure.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Here's a set of 2 patches against DaveM's 'net-next.git' repo. With those,
I'm somewhat simplifying the TSU init code in the driver probe() method...
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Sergei Shtylyov [Sun, 14 Jan 2018 17:47:44 +0000 (20:47 +0300)]
sh_eth: get Ether port # only when needed
The dual-port Ether configurations always have a shared TSU to e.g. pass
the packets between those ports. With the TSU init. code gathered under
the single *if*, we now can only get the port # from 'platform_device::id'
only when we actually need it (and not recalculate it each time)...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: David S. Miller <davem@davemloft.net>
Sergei Shtylyov [Sun, 14 Jan 2018 17:47:43 +0000 (20:47 +0300)]
sh_eth: gather all TSU init code in one place
The sh_eth_cpu_data::chip_reset() method always resets using ARSTR and
this register is always located at the start of the TSU register region.
Therefore, we can only call this method if we know TSU is there and thus
simplify the probing code a bit...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 15 Jan 2018 19:46:16 +0000 (14:46 -0500)]
Merge tag 'wireless-drivers-next-for-davem-2018-01-13' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.16
Here are patches which have been accumulating over the holidays and
after the New Year. Business as usual and nothing special really
standing out.
But what's noteworthy here is that Larry Finger is stepping down as
the rtlwifi maintainer. He has been maintaining rtlwifi since it was
applied back in 2010 in commit 0c8173385e54 ("rtl8192ce: Add new
driver") and it has been no easy role trying to juggle between the
vendor, demanding upstream community and users. So big thank you to
Larry for all his efforts!
ath10k
* more preparation work for wcn3990 support
* add memory dump to firmware coredump files
wil6210
* support scheduled scan
* support 40-bit DMA addresses
qtnfmac
* support MAC address based access control
* support for radar detection and Channel Availibility Check (CAC)
mwifiex
* firmware coredump for usb devices
rtlwifi
* Larry Finger steps down as the maintainer and Ping-Ke Shih becomes
the new maintainer
* add debugfs interfaces to dump register and btcoex status, and also
write registers and h2c
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Walleij [Fri, 12 Jan 2018 21:34:24 +0000 (22:34 +0100)]
net: ethernet: Add a driver for Gemini gigabit ethernet
The Gemini ethernet has been around for years as an out-of-tree
patch used with the NAS boxen and routers built on StorLink
SL3512 and SL3516, later Storm Semiconductor, later Cortina
Systems. These ASICs are still being deployed and brand new
off-the-shelf systems using it can easily be acquired.
The full name of the IP block is "Net Engine and Gigabit
Ethernet MAC" commonly just called "GMAC".
The hardware block contains a common TCP Offload Enginer (TOE)
that can be used by both MACs. The current driver does not use
it.
Cc: Tobias Waldvogel <tobias.waldvogel@gmail.com> Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Walleij [Fri, 12 Jan 2018 21:34:23 +0000 (22:34 +0100)]
net: ethernet: Add DT bindings for the Gemini ethernet
This adds the device tree bindings for the Gemini ethernet
controller. It is pretty straight-forward, using standard
bindings and modelling the two child ports as child devices
under the parent ethernet controller device.
Cc: devicetree@vger.kernel.org Cc: Tobias Waldvogel <tobias.waldvogel@gmail.com> Cc: Michał Mirosław <mirq-linux@rere.qmqm.pl> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Fri, 12 Jan 2018 20:07:36 +0000 (22:07 +0200)]
ipv6: Fix build with gcc-4.4.5
Emil reported the following compiler errors:
net/ipv6/route.c: In function `rt6_sync_up`:
net/ipv6/route.c:3586: error: unknown field `nh_flags` specified in initializer
net/ipv6/route.c:3586: warning: missing braces around initializer
net/ipv6/route.c:3586: warning: (near initialization for `arg.<anonymous>`)
net/ipv6/route.c: In function `rt6_sync_down_dev`:
net/ipv6/route.c:3695: error: unknown field `event` specified in initializer
net/ipv6/route.c:3695: warning: missing braces around initializer
net/ipv6/route.c:3695: warning: (near initialization for `arg.<anonymous>`)
Problem is with the named initializers for the anonymous union members.
Fix this by adding curly braces around the initialization.
Fixes: 4c981e28d373 ("ipv6: Prepare to handle multiple netdev events") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reported-by: Emil S Tantilov <emils.tantilov@gmail.com> Tested-by: Emil S Tantilov <emils.tantilov@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Maloy [Fri, 12 Jan 2018 19:56:50 +0000 (20:56 +0100)]
tipc: fix bug during lookup of multicast destination nodes
In commit 232d07b74a33 ("tipc: improve groupcast scope handling") we
inadvertently broke non-group multicast transmission when changing the
parameter 'domain' to 'scope' in the function
tipc_nametbl_lookup_dst_nodes(). We missed to make the corresponding
change in the calling function, with the result that the lookup always
fails.
A closer anaysis reveals that this parameter is not needed at all.
Non-group multicast is hard coded to use CLUSTER_SCOPE, and in the
current implementation this will be delivered to all matching
destinations except those which are published with NODE_SCOPE on other
nodes. Since such publications never will be visible on the sending node
anyway, it makes no sense to discriminate by scope at all.
We now remove this parameter altogether.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Kirill Tkhai [Fri, 12 Jan 2018 15:28:31 +0000 (18:28 +0300)]
net: Convert atomic_t net::count to refcount_t
Since net could be obtained from RCU lists,
and there is a race with net destruction,
the patch converts net::count to refcount_t.
This provides sanity checks for the cases of
incrementing counter of already dead net,
when maybe_get_net() has to used instead
of get_net().
Drivers: allyesconfig and allmodconfig are OK.
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Reviewed-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Wed, 10 Jan 2018 20:21:31 +0000 (21:21 +0100)]
net: phy: remove parameter new_link from phy_mac_interrupt()
I see two issues with parameter new_link:
1. It's not needed. See also phy_interrupt(), works w/o this parameter.
phy_mac_interrupt sets the state to PHY_CHANGELINK and triggers the
state machine which then calls phy_read_status. And phy_read_status
updates the link state.
2. phy_mac_interrupt is used in interrupt context and getting the link
state may sleep (at least when having to access the PHY registers
via MDIO bus).
So let's remove it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Tested-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Maloy [Wed, 10 Jan 2018 20:08:50 +0000 (21:08 +0100)]
tipc: fix a potental access after delete in tipc_sk_join()
In commit d12d2e12cec2 "tipc: send out join messages as soon as new
member is discovered") we added a call to the function tipc_group_join()
without considering the case that the preceding tipc_sk_publish() might
have failed, and the group item already deleted.
We fix this by returning from tipc_sk_join() directly after the
failed tipc_sk_publish.
Reported-by: syzbot+e3eeae78ea88b8d6d858@syzkaller.appspotmail.com Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
net: dsa: lan9303: check error value from devm_gpiod_get_optional()
Errors need to be prograted back from probe.
Note: I have only compile tested the code as I don't have the hardware.
Egil Hjelmeland <privat@egil-hjelmeland.no> has tested it but I haven't
added at Test-by: wasn't in the standard form. Not sure if that's ok or
not.
Changes from v1:
- rebased on net-next
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Phil Reid [Wed, 10 Jan 2018 07:39:33 +0000 (15:39 +0800)]
net: dsa: lan9303: check error value from devm_gpiod_get_optional()
devm_gpiod_get_optional() can return an error in addition to a NULL ptr.
Check for error and propagate that to the probe function. Check return
value in probe. This will now handle EPROBE_DEFER for the reset gpio.
Signed-off-by: Phil Reid <preid@electromag.com.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Fri, 12 Jan 2018 14:01:36 +0000 (15:01 +0100)]
net: phy: Have __phy_modify return 0 on success
__phy_modify would return the old value of the register before it was
modified. Thus on success, it does not return 0, but a positive value.
Thus functions using phy_modify, which is a wrapper around
__phy_modify, can start returning > 0 on success, rather than 0. As a
result, breakage has been noticed in various places, where 0 was
assumed.
Code inspection does not find any current location where the return of
the old value is currently used. So have __phy_modify return 0 on
success. When there is a real need for the old value, either a new
accessor can be added, or an additional parameter passed.
Fixes: fea23fb591cc ("net: phy: convert read-modify-write to phy_modify()") Fixes: 2b74e5be17d2 ("net: phy: add phy_modify() accessor") Reported-by: Geert Uytterhoeven <geert@linux-m68k.org> Tested-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Niklas Cassel <niklas.cassel@axis.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 14 Jan 2018 17:25:04 +0000 (12:25 -0500)]
Merge branch '10GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
10GbE Intel Wired LAN Driver Updates 2018-01-12
This series contains updates to ixgbe, fm10k and net core.
Alex updates the driver to remove a duplicate MAC address check and
verifies that we have not run out of resources to configure a MAC rule
in our filter table. Also do not assume that dev->num_tc was populated
and configured with the driver, since it can be configured via mqprio
without any hardware coordination. Fixed the recording of stats for
MACVLAN in ixgbe and fm10k instead of recording the receive queue on
MACVLAN offloaded frames. When handling a MACVLAN offload, we should
be stopping/starting traffic on our own queues instead of the upper
devices transmit queues. Fixed possible race conditions with the
MACVLAN cleanup with the interface cleanup on shutdown. With the
recent fixes to ixgbe, we can cap the number of queues regardless of
accel_priv being in use or not, since the actual number of queues are
being reported via real_num_tx_queues.
Tony fixes up the kernel documentation for ixgbe and ixgbevf to resolve
warnings when W=1 is used.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 14 Jan 2018 17:21:12 +0000 (12:21 -0500)]
Merge branch 'mlxsw-Offload-PRIO-qdisc'
Jiri Pirko says:
====================
mlxsw: Offload PRIO qdisc
Nogah says:
Add an offload support for PRIO qdisc for mlxsw driver.
PRIO qdisc is being offloaded by using ndo_setup_tc. It has three
commands, to set or tune the qdisc, to remove it and to get its stats.
Like RED offloading, offloading this qdisc is not enforced on the driver
and determining its offload state is done in the dump action, when the
stats are being updated.
In the driver, offloading of PRIO is supported as root qdisc only. It
supports only priorities 0-7 (the range that is used by the current static
mapping of DSCP to skb prio and by 1:1 PCP values mapping) and up to 8
bands.
Patches 1-2 offload DSCP to priority mapping in the mlxsw_sp driver.
Patch 3 adds offload support for PRIO qdisc.
Patches 4-5 Add PRIO offload support in the mlxsw_sp driver.
---
v1->v2:
- Patch 1/5:
- Rewrite patch msg
- Patch 3/5:
- Send all the qstats in the replace command (and not just backlog)
- Patch 5/5:
- Align with the changes from 3/5
- Move backlog to the generic qdisc stats struct
- Delete extra newline
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Nogah Frankel [Sun, 14 Jan 2018 11:33:17 +0000 (12:33 +0100)]
mlxsw: spectrum: qdiscs: Support stats for PRIO qdisc
Support basic stats for PRIO qdisc, which includes tx packets and bytes
count, drops count and backlog size. The rest of the stats are irrelevant
for this qdisc offload.
Since backlog is not only incremental but reflecting momentary value, in
case of a qdisc that stops being offloaded but is not destroyed, backlog
value needs to be updated about the un-offloading.
For that reason an unoffload function is being added to the ops struct.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com> Reviewed-by: Yuval Mintz <yuvalm@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Nogah Frankel [Sun, 14 Jan 2018 11:33:16 +0000 (12:33 +0100)]
mlxsw: spectrum: qdiscs: Support PRIO qdisc offload
Add support for offloading PRIO qdisc as root qdisc.
The support is for up to 8 bands.
Routed packets priority is determined by the DSCP field with the default
translations. Bridged packets priority is determined by the PCP field, if
exist, otherwise it is set to 0.
Since both options have only priorities 0-7, higher priorities mapping are
being ignored.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com> Reviewed-by: Yuval Mintz <yuvalm@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Nogah Frankel [Sun, 14 Jan 2018 11:33:15 +0000 (12:33 +0100)]
net: sch: prio: Add offload ability to PRIO qdisc
Add the ability to offload PRIO qdisc by using ndo_setup_tc.
There are three commands for PRIO offloading:
* TC_PRIO_REPLACE: handles set and tune
* TC_PRIO_DESTROY: handles qdisc destroy
* TC_PRIO_STATS: updates the qdiscs counters (given as reference)
Like RED qdisc, the indication of whether PRIO is being offloaded is being
set and updated as part of the dump function. It is so because the driver
could decide to offload or not based on the qdisc parent, which could
change without notifying the qdisc.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com> Reviewed-by: Yuval Mintz <yuvalm@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
When routing ip packets, the kernel is setting the SKB's priority
based on the tos field of the packet.
Imitate this behavior in the mlxsw router, having the internal
switch priority of a routed packet determined according to its DS
field.
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com> Signed-off-by: Nogah Frankel <nogahf@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Sun, 14 Jan 2018 11:33:13 +0000 (12:33 +0100)]
mlxsw: reg: add rdpm register
Add rdpm definition - router DSCP to priority mapping register.
This register will be utilized later to align the default mapping between
packet DSCP and switch-priority to the kernel's mapping between
packet priority and skb priority.
This is the first non-bit indexed register where the entries are arranged
in descending order, i.e., entry at offset 0 matches configuration for
dscp[63]. As a result, the item's step is converted into a signed variable
to support descending arrays [where step would be negative].
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com> Signed-off-by: Nogah Frankel <nogahf@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 14 Jan 2018 17:08:45 +0000 (12:08 -0500)]
Merge branch 'dsa-mv88e6xxx-ATU-VTU-irq'
Andrew Lunn says:
====================
mv88e6xxx: ATU and VTU interrupts
Both the ATU and VTU of Mavell switches can generate interrupts when
violations occur. Trap this interrupts and print what violation
occurred.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sun, 14 Jan 2018 01:32:45 +0000 (02:32 +0100)]
net: dsa: mv88e6xxx: Decode VTU problem interrupt
When there is a problem with the VTU, an interrupt can be
generated. Trap this interrupt and decode the registers to determine
what the problem was, then log the error.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sun, 14 Jan 2018 01:32:44 +0000 (02:32 +0100)]
net: dsa: mv88e6xxx: Decode ATU problem interrupt
When there is a problem with the ATU, an interrupt can be
generated. Trap this interrupt and decode the registers to determine
what the problem was, then log the error.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Fri, 12 Jan 2018 16:15:59 +0000 (17:15 +0100)]
mlxsw: spectrum_router: Add support for IPv6 non-equal-cost multipath
Since commit eb789980d0aa ("mlxsw: spectrum_router: Populate adjacency
entries according to weights") the driver includes support for
non-equal-cost multipath, but IPv4 nexthops were the only user.
Now that the kernel supports weighted IPv6 nexthops, we can extend the
driver to support it as well.
This is done by assigning each nexthop its configured weight, so that it
will be populated accordingly in the device's adjacency table. The
`weight` parameter is also taken into account when comparing nexthop
groups in order not to consolidate non-identical groups.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Sat, 13 Jan 2018 21:13:44 +0000 (22:13 +0100)]
net: netsec: use dma_addr_t for storing dma address
On targets that have different sizes for phys_addr_t and dma_addr_t,
we get a type mismatch error:
drivers/net/ethernet/socionext/netsec.c: In function 'netsec_alloc_dring':
drivers/net/ethernet/socionext/netsec.c:970:9: error: passing argument 3 of 'dma_zalloc_coherent' from incompatible pointer type [-Werror=incompatible-pointer-types]
The code is otherwise correct, as the address is never actually used as a
physical address but only passed into a DMA register. For consistently,
I'm changing the variable name as well, to clarify that this is a DMA
address.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen [Mon, 4 Dec 2017 19:28:31 +0000 (11:28 -0800)]
ixgbevf: Fix kernel-doc format warnings
Recent checks added for formatting kernel-doc comments are causing warnings
if W= is run with a non-zero value. This patch fixes function comments to
resolve warnings when W=1 is used.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tony Nguyen [Mon, 4 Dec 2017 19:28:30 +0000 (11:28 -0800)]
ixgbe: Fix kernel-doc format warnings
Recent checks added for formatting kernel-doc comments are causing warnings
if W= is run with a non-zero value. This patch fixes function comments to
resolve warnings when W=1 is used.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Wed, 22 Nov 2017 18:57:41 +0000 (10:57 -0800)]
net: Cap number of queues even with accel_priv
With the recent fix to ixgbe we can cap the number of queues always
regardless of if accel_priv is being used or not since the actual number of
queues are being reported via real_num_tx_queues.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Wed, 22 Nov 2017 18:57:35 +0000 (10:57 -0800)]
ixgbe: Fix handling of macvlan Tx offload
This update makes it so that we report the actual number of Tx queues via
real_num_tx_queues but are still restricted to RSS on only the first pool
by setting num_tc equal to 1. Doing this locks us into only having the
ability to setup XPS on the queues in that pool, and only those queues
should be used for transmitting anything other than macvlan traffic.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Wed, 22 Nov 2017 18:57:29 +0000 (10:57 -0800)]
ixgbe: avoid bringing rings up/down as macvlans are added/removed
This change makes it so that instead of bringing rings up/down for various
we just update the netdev pointer for the Rx ring and set or clear the MAC
filter for the interface. By doing it this way we can avoid a number of
races and issues in the code as things were getting messy with the macvlan
clean-up racing with the interface clean-up to bring the rings down on
shutdown.
With this change we opt to leave the rings owned by the PF interface for
both Tx and Rx and just direct the packets once they are received to the
macvlan netdev.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Wed, 22 Nov 2017 18:57:23 +0000 (10:57 -0800)]
ixgbe: Do not manipulate macvlan Tx queues when performing macvlan offload
We should not be stopping/starting the upper devices Tx queues when
handling a macvlan offload. Instead we should be stopping and starting
traffic on our own queues.
In order to prevent us from doing this I am updating the code so that we no
longer change the queue configuration on the upper device, nor do we update
the queue_index on our own device. Instead we can just use the queue index
for our local device and not update the netdev in the case of the transmit
rings.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Wed, 22 Nov 2017 18:57:17 +0000 (10:57 -0800)]
ixgbe/fm10k: Record macvlan stats instead of Rx queue for macvlan offloaded rings
We shouldn't be recording the Rx queue on macvlan offloaded frames since
the macvlan is normally brought up as a single queue device, and it will
trigger warnings for RPS if we have recorded queue IDs larger than the
"real_num_rx_queues" value recorded for the device.
Instead we should be recording the macvlan statistics since we are
bypassing the normal macvlan statistics that would have been generated by
the receive path.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Wed, 22 Nov 2017 18:57:11 +0000 (10:57 -0800)]
ixgbe: Don't assume dev->num_tc is equal to hardware TC config
The code throughout ixgbe was assuming that dev->num_tc was populated and
configured with the driver, when in fact this can be configured via mqprio
without any hardware coordination other than restricting us to the real
number of Tx queues we advertise.
Instead of handling things this way we need to keep a local copy of the
number of TCs in use so that we don't accidentally pull in the TC
configuration from mqprio when it is configured in software mode.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Wed, 22 Nov 2017 18:57:05 +0000 (10:57 -0800)]
ixgbe: Default to 1 pool always being allocated
We might as well configure the limit to default to 1 pool always for the
interface. This accounts for the fact that the PF counts as 1 pool if
SR-IOV is enabled, and in general we are always running in 1 pool mode when
RSS or DCB is enabled as well, though we don't need to actually evaluate
any of the VMDq features in those cases.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Wed, 22 Nov 2017 18:56:59 +0000 (10:56 -0800)]
ixgbe: Assume provided MAC filter has been verified by macvlan
The macvlan driver itself will validate the MAC address that is configured
for a given interface. There is no need for us to verify it again.
Instead we should be checking to verify that we actually allocate the filter
and have not run out of resources to configure a MAC rule in our filter
table.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
====================
hns3: add some new features and fix some bugs
This patchset adds 3 ethtool features: get_channels,
get_coalesce and get_coalesce, and fix some bugs.
[patch 1/11] adds ethtool_ops.get_channels (ethtool -l) support
for VF.
[patch 2/11] removes TSO config command from VF driver,
as only main PF can config TSO MSS length according to
hardware.
[patch 3/11 - 4/11] add ethtool_ops {get|set}_coalesce
(ethtool -c/-C) support to PF.
[patch 5/11 - 9/11] fix some bugs related to {get|set}_coalesce.
[patch 10/11 - 11/11] fix the features handling in
hns3_nic_set_features(). Local variable "changed" was defined
to indicates features changed, but was used only for feature
NETIF_F_HW_VLAN_CTAG_RX. Add checking to improve the reliability.
---
Change log:
V1 -> V2:
1, Rewrite the cover letter requested by David Miller.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jian Shen [Fri, 12 Jan 2018 08:23:16 +0000 (16:23 +0800)]
net: hns3: add feature check when feature changed
Local variable "changed" was defined to indicates features changed,
but was used only for feature NETIF_F_HW_VLAN_CTAG_RX. Add checking
for other features.
Fixes: 052ece6dc19c ("net: hns3: add ethtool related offload command") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Fuyun Liang [Fri, 12 Jan 2018 08:23:15 +0000 (16:23 +0800)]
net: hns3: add int_gl_idx setup for TX and RX queues
If the int_gl_idx does not be set, the default interrupt coalesce index
is 0. The TX queues and the RX queues will both use the GL0 as the
interrupt coalesce GL switch. But it should be GL1 for TX queues and GL0
for RX queues.
This patch adds the int_gl_idx setup for TX queues and RX queues.
Fixes: 76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC") Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Fuyun Liang [Fri, 12 Jan 2018 08:23:13 +0000 (16:23 +0800)]
net: hns3: remove unused GL setup function
Since the TX GL and the RX GL need to be set separately,
hns3_set_vector_coalesc_gl() has been replaced with
hns3_set_vector_coalesce_rx_gl() and hns3_set_vector_coalesce_tx_gl().
This patch removes hns3_set_vector_coalesc_gl().
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Fuyun Liang [Fri, 12 Jan 2018 08:23:12 +0000 (16:23 +0800)]
net: hns3: refactor GL update function
The GL update function uses the max GL value between tx_int_gl and
rx_int_gl to set both new tx_int_gl and new rx_int_gl. Therefore, User
can not enable TX GL self-adaptive or RX GL self-adaptive individually.
This patch refactors the code to update the TX GL and the RX GL
separately, making user can enable TX GL self-adaptive or RX GL
self-adaptive individually.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Fuyun Liang [Fri, 12 Jan 2018 08:23:11 +0000 (16:23 +0800)]
net: hns3: refactor interrupt coalescing init function
In the hardware, the coalesce configurable registers include GL0, GL1,
GL2. In the driver, the TX queues use the register GL1 and the RX queues
use the register GL0. This function initializes the configuration of the
interrupt coalescing, but does not distinguish between the TX direction
and the RX direction. It will cause some confusion.
This patch refactors the function to initialize the TX GL and the RX GL
separately. And the initialization of related variables also is added to
this patch.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
BPF alignment tests got a conflict because the registers
are output as Rn_w instead of just Rn in net-next, and
in net a fixup for a testcase prohibits logical operations
on pointers before using them.
Also, we should attempt to patch BPF call args if JIT always on is
enabled. Instead, if we fail to JIT the subprogs we should pass
an error back up and fail immediately.
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 12 Jan 2018 00:57:32 +0000 (16:57 -0800)]
Merge tag 'ceph-for-4.15-rc8' of git://github.com/ceph/ceph-client
Pull ceph fixes from Ilya Dryomov:
"Two rbd fixes for 4.12 and 4.2 issues respectively, marked for
stable"
* tag 'ceph-for-4.15-rc8' of git://github.com/ceph/ceph-client:
rbd: set max_segments to USHRT_MAX
rbd: reacquire lock should update lock owner client id
Linus Torvalds [Fri, 12 Jan 2018 00:54:35 +0000 (16:54 -0800)]
Merge tag 'gpio-v4.15-4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fix from Linus Walleij:
"Fix a raw vs elaborate GPIO descriptor bug introduced by yours truly"
* tag 'gpio-v4.15-4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: Add missing open drain/source handling to gpiod_set_value_cansleep()
Jia-Ju Bai [Tue, 9 Jan 2018 01:40:06 +0000 (09:40 +0800)]
b43: Replace mdelay with usleep_range in b43_radio_2057_init_post
b43_radio_2057_init_post is not called in an interrupt handler
nor holding a spinlock.
The function mdelay in it can be replaced with usleep_range,
to reduce busy wait.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Himanshu Jha [Mon, 8 Jan 2018 20:45:31 +0000 (02:15 +0530)]
brcmfmac: Use zeroing memory allocator than allocator/memset
Use dma_zalloc_coherent for allocating zeroed
memory and remove unnecessary memset function.
Generated-by: scripts/coccinelle/api/alloc/kzalloc-simple.cocci Suggested-by: Luis R. Rodriguez <mcgrof@kernel.org> Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Various BPF related improvements and fixes to nfp driver: i) do
not register XDP RXQ structure to control queues, ii) round up
program stack size to word size for nfp, iii) restrict MTU changes
when BPF offload is active, iv) add more fully featured relocation
support to JIT, v) add support for signed compare instructions to
the nfp JIT, vi) export and reuse verfier log routine for nfp, and
many more, from Jakub, Quentin and Nic.
2) Fix a syzkaller reported GPF in BPF's copy_verifier_state() when
we hit kmalloc failure path, from Alexei.
3) Add two follow-up fixes for the recent XDP RXQ series: i) kvzalloc()
allocated memory was only kfree()'ed, and ii) fix a memory leak where
RX queue was not freed in netif_free_rx_queues(), from Jakub.
4) Add a sample for transferring XDP meta data into the skb, here it
is used for setting skb->mark with the buffer from XDP, from Jesper.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Here's likely the last bluetooth-next pull request for the 4.16 kernel.
- Added support for Bluetooth on 2015+ MacBook (Pro)
- Fix to QCA Rome suspend/resume handling
- Two new QCA_ROME USB IDs in btusb
- A few other minor fixes
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Yongjun [Thu, 11 Jan 2018 11:21:51 +0000 (11:21 +0000)]
net: phy: mdio-bcm-unimac: fix potential NULL dereference in unimac_mdio_probe()
platform_get_resource() may fail and return NULL, so we should
better check it's return value to avoid a NULL pointer dereference
a bit later in the code.
This is detected by Coccinelle semantic patch.
@@
expression pdev, res, n, t, e, e1, e2;
@@
res = platform_get_resource(pdev, t, n);
+ if (!res)
+ return -EINVAL;
... when != res == NULL
e = devm_ioremap(e1, res->start, e2);
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Thu, 11 Jan 2018 10:36:24 +0000 (11:36 +0100)]
net: socionext: include linux/io.h to fix build
I ran into a randconfig build failure:
drivers/net/ethernet/socionext/netsec.c: In function 'netsec_probe':
drivers/net/ethernet/socionext/netsec.c:1583:17: error: implicit declaration of function 'devm_ioremap'; did you mean 'ioremap'? [-Werror=implicit-function-declaration]
Including linux/io.h directly fixes this.
Fixes: 533dd11a12f6 ("net: socionext: Add Synquacer NetSec driver") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
brcmfmac: add comment block in brcmf_sdio_buscore_read()
In brcmf_sdio_buscore_read() there is some special handling upon
register access to chipid register of the chipcommon core. Add
comment explaining why it is done here.
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Replace the array of functions with a pair of pointers to the
relevant functions.
Signed-off-by: Ian Molton <ian@mnementh.co.uk> Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
David S. Miller [Thu, 11 Jan 2018 16:59:44 +0000 (11:59 -0500)]
Merge branch '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2018-01-10
This series contains updates to i40e and i40evf only.
Alice adds the displaying of priority xon/xoff packet stats, since we
were already keeping track of them. Based on the recent changes, bump
the driver versions.
Jake changes how the driver determines whether or not the device is
currently up to resolve the possible issue of freeing data structures
and other memory before they have been fully allocated. Refactored
the driver to simplify the locking behavior and to consistently use
spinlocks instead of an overloaded bit lock to protect MAC and filter
lists. Created a helper function which can convert the AdminQ link
speed definition into a virtchnl definition.
Colin Ian King cleans up a redundant variable initialization.
Alex cleans up the driver to stop clearing the pending bit array for
each vector manually, since it is prone to dropping an interrupt and
based on the hardware specs, the pending bit array will be cleared
automatically in MSI-X mode. Cleaned up flags for promiscuous mode to
resolve an issue where enabling & disabling promiscuous mode on a VF
would leave us in a high polling rate for the adminq task. Cleaned up
code that was prone to race issues.
Jingjing renames pipeline personalization profile (ppp) to dynamic
device personalization (ddp) because it was being confused with the
well known point to point protocol. Also removed checks for "track_id"
being zero, since it is valid for it to be zero for profiles that do
not have any 'write' commands.
v2: cleaned up commit message for patch 12 based on feedback from Sergei
Shtylyov and Alex Duyck
v3: dropped patch 15 from the original series while Mariusz Stachura
works on the changes that Jakub Kicinski has suggested
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Nathan Fontenot [Wed, 10 Jan 2018 16:40:09 +0000 (10:40 -0600)]
ibmvnic: Don't handle RX interrupts when not up.
Initiating a kdump via the command line can cause a pending interrupt
to be handled by the ibmvnic driver when initializing the sub-CRQ
irqs during driver initialization.
Kalle Valo [Thu, 11 Jan 2018 16:29:54 +0000 (18:29 +0200)]
Merge tag 'iwlwifi-next-for-kalle-2017-12-20' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
Third batch of updates for v4.16
* Small cleanups in the new rate-scaling code;
* Some improvements in debugging;
* New FW API changes;
* Fix a bug where we got a false-positive warning;
* Fix forced quota debugfs functionality;
Ganesh Goudar [Wed, 10 Jan 2018 12:45:26 +0000 (18:15 +0530)]
cxgb4: add support for vxlan segmentation offload
add changes to t4_eth_xmit to enable vxlan segmentation
offload support.
Original work by: Santosh Rastapur <santosh@chelsio.com> Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ganesh Goudar [Wed, 10 Jan 2018 12:45:08 +0000 (18:15 +0530)]
cxgb4: implement udp tunnel callbacks
Implement ndo_udp_tunnel_add and ndo_udp_tunnel_del
to support vxlan tunnelling.
Original work by: Santosh Rastapur <santosh@chelsio.com> Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ganesh Goudar [Wed, 10 Jan 2018 12:44:49 +0000 (18:14 +0530)]
cxgb4: add data structures to support vxlan
Add data structures and macros to be used in vxlan
offload.
Original work by: Santosh Rastapur <santosh@chelsio.com> Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
1) BPF speculation prevention and BPF_JIT_ALWAYS_ON, from Alexei
Starovoitov.
2) Revert dev_get_random_name() changes as adjust the error code
returns seen by userspace definitely breaks stuff.
3) Fix TX DMA map/unmap on older iwlwifi devices, from Emmanuel
Grumbach.
4) From wrong AF family when requesting sock diag modules, from Andrii
Vladyka.
5) Don't add new ipv6 routes attached to the null_entry, from Wei Wang.
6) Some SCTP sockopt length fixes from Marcelo Ricardo Leitner.
7) Don't leak when removing VLAN ID 0, from Cong Wang.
8) Hey there's a potential leak in ipv6_make_skb() too, from Eric
Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (27 commits)
ipv6: sr: fix TLVs not being copied using setsockopt
ipv6: fix possible mem leaks in ipv6_make_skb()
mlxsw: spectrum_qdisc: Don't use variable array in mlxsw_sp_tclass_congestion_enable
mlxsw: pci: Wait after reset before accessing HW
nfp: always unmask aux interrupts at init
8021q: fix a memory leak for VLAN 0 device
of_mdio: avoid MDIO bus removal when a PHY is missing
caif_usb: use strlcpy() instead of strncpy()
doc: clarification about setting SO_ZEROCOPY
net: gianfar_ptp: move set_fipers() to spinlock protecting area
sctp: make use of pre-calculated len
sctp: add a ceiling to optlen in some sockopts
sctp: GFP_ATOMIC is not needed in sctp_setsockopt_events
bpf: introduce BPF_JIT_ALWAYS_ON config
bpf: avoid false sharing of map refcount with max_entries
ipv6: remove null_entry before adding default route
SolutionEngine771x: add Ether TSU resource
SolutionEngine771x: fix Ether platform data
docs-rst: networking: wire up msg_zerocopy
net: ipv4: emulate READ_ONCE() on ->hdrincl bit-field in raw_sendmsg()
...
samples/bpf: xdp2skb_meta shows transferring info from XDP to SKB
Creating a bpf sample that shows howto use the XDP 'data_meta'
infrastructure, created by Daniel Borkmann. Very few drivers support
this feature, but I wanted a functional sample to begin with, when
working on adding driver support.
XDP data_meta is about creating a communication channel between BPF
programs. This can be XDP tail-progs, but also other SKB based BPF
hooks, like in this case the TC clsact hook. In this sample I show
that XDP can store info named "mark", and TC/clsact chooses to use
this info and store it into the skb->mark.
It is a bit annoying that XDP and TC samples uses different tools/libs
when attaching their BPF hooks. As the XDP and TC programs need to
cooperate and agree on a struct-layout, it is best/easiest if the two
programs can be contained within the same BPF restricted-C file.
As the bpf-loader, I choose to not use bpf_load.c (or libbpf), but
instead wrote a bash shell scripted named xdp2skb_meta.sh, which
demonstrate howto use the iproute cmdline tools 'tc' and 'ip' for
loading BPF programs. To make it easy for first time users, the shell
script have command line parsing, and support --verbose and --dry-run
mode, if you just want to see/learn the tc+ip command syntax:
# ./xdp2skb_meta.sh --dev ixgbe2 --dry-run
# Dry-run mode: enable VERBOSE and don't call TC+IP
tc qdisc del dev ixgbe2 clsact
tc qdisc add dev ixgbe2 clsact
tc filter add dev ixgbe2 ingress prio 1 handle 1 bpf da obj ./xdp2skb_meta_kern.o sec tc_mark
# Flush XDP on device: ixgbe2
ip link set dev ixgbe2 xdp off
ip link set dev ixgbe2 xdp obj ./xdp2skb_meta_kern.o sec xdp_mark
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Al Viro [Wed, 10 Jan 2018 23:47:05 +0000 (18:47 -0500)]
Fix a leak in socket(2) when we fail to allocate a file descriptor.
Got broken by "make sock_alloc_file() do sock_release() on failures" -
cleanup after sock_map_fd() failure got pulled all the way into
sock_alloc_file(), but it used to serve the case when sock_map_fd()
failed *before* getting to sock_alloc_file() as well, and that got
lost. Trivial to fix, fortunately.
Fixes: 8e1611e23579 (make sock_alloc_file() do sock_release() on failures) Reported-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
====================
sfc: support 25G configuration with ethtool
Adds support for advertise bits beyond the 32-bit legacy masks, and plumbs in
translation of the new 25/50/100G bits to/from MCDI.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Edward Cree [Wed, 10 Jan 2018 18:00:14 +0000 (18:00 +0000)]
sfc: support the ethtool ksettings API properly so that 25/50/100G works
Store and handle ethtool link mode masks within the driver instead of
just a single u32. However, quite a significant amount of existing code
wants to manipulate the masks directly, and thus now uses the first
unsigned long (i.e. mask[0]) as though it were a legacy u32 mask. This
is ok because all the bits that code is interested in are in the first
32 bits of the mask; but it might be a good idea to change them in
future to use the proper bitmap API.
Signed-off-by: Edward Cree <ecree@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Edward Cree [Wed, 10 Jan 2018 17:59:59 +0000 (17:59 +0000)]
sfc: basic MCDI mapping of 25/50/100G link speeds
Only handles direct speed setting, not autoneg, because the driver is
still trying to pretend it uses the legacy ethtool API which doesn't
have advertised/supported bits for 25/50/100G.
Signed-off-by: Edward Cree <ecree@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 10 Jan 2018 21:07:42 +0000 (16:07 -0500)]
Merge branch 'mlxsw-qdisc-refactoring'
Jiri Pirko says:
====================
mlxsw qdisc refactoring
This patchset refactors the qdisc handling in mlxsw driver in order to make
it more object oriented like.
It helps readability, laying the groundwork for the offloading of
additional qdiscs by the driver
This patchset also makes the qdiscs statistics more generic.
Patch 1 moves the qdiscs declaration to the spectrum_qdisc.c
Patches 2-3 clean the offloaded stats requests. Patch 2 changes the RED
generic stats struct to be sharable by other offloaded qdiscs. Patch 3
changes the xstats request to be like the stats. Note that these patches
are outside the driver scope.
Patches 4-5 clean the statistics related functions and structs within the
driver.
Patches 6-7 decrease the need for the same parameters to be sent to many
functions.
Patches 8-11 create a functions pointers struct, to make the qdiscs
handling more object oriented like.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Nogah Frankel [Wed, 10 Jan 2018 14:00:07 +0000 (15:00 +0100)]
mlxsw: spectrum: qdiscs: Remove qdisc before setting a new one
If a qdisc is being replaced by another qdisc of the same type, it can
simply override over its configuration.
However, if it replaces a qdisc of another type, it needs to be removed
before setting the new qdisc.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com> Reviewed-by: Yuval Mintz <yuvalm@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Nogah Frankel [Wed, 10 Jan 2018 14:00:06 +0000 (15:00 +0100)]
mlxsw: spectrum: qdiscs: Create a generic replace function
Create a generic qdisc replace function.
For that goal, add three functions to the qdisc ops struct:
* check_params: Checks if the given parameters are offloadable.
* replace: Offload the given parameters.
* clean_stats: clean the qdisc stats for the offloaded qdisc.
integrate RED offloading into using the new internal replace API.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com> Reviewed-by: Yuval Mintz <yuvalm@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Nogah Frankel [Wed, 10 Jan 2018 14:00:05 +0000 (15:00 +0100)]
mlxsw: spectrum: qdiscs: Create a generic destroy function
Add a destroy function to the qdiscs ops struct.
Create a generic qdisc destroy function, that clears the qdisc metadata as
well as calling the specific qdisc destroy function.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com> Reviewed-by: Yuval Mintz <yuvalm@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Nogah Frankel [Wed, 10 Jan 2018 14:00:04 +0000 (15:00 +0100)]
mlxsw: spectrum: qdiscs: Add an ops struct
Qdisc struct have the Qdisc_class_ops struct.
This patch introduces the similar ops struct for the mlxsw_sp_qdisc_ops
struct. It allows better readability as well as code reusability for the
common parts of some functions like destroy.
The first operations to be added are the statistics getters.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com> Reviewed-by: Yuval Mintz <yuvalm@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Nogah Frankel [Wed, 10 Jan 2018 14:00:03 +0000 (15:00 +0100)]
mlxsw: spectrum: qdiscs: Unite all handle checks
Every qdisc op gets the qdisc handle ID as well as its location. Each one
of them, beside replace, checks if the handle doesn't match the qdisc in
the given location, and if so, it returns without running the actual op.
Unite these checks to one comparison function and avoid sending the handle
id to these ops.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com> Reviewed-by: Yuval Mintz <yuvalm@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Nogah Frankel [Wed, 10 Jan 2018 14:00:02 +0000 (15:00 +0100)]
mlxsw: spectrum: qdiscs: Add tclass number to the mlxsw_sp_qdisc
Tclass number is needed for most of the operations related to the qdisc in
the driver. Create a field for it in the mlxsw_sp_qdisc instead of passing
it to every function as parameter.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com> Reviewed-by: Yuval Mintz <yuvalm@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / mirror_ubuntu-eoan-kernel.git / log