Shengjiu Wang [Fri, 17 Jun 2022 07:44:37 +0000 (15:44 +0800)]
ASoC: fsl_sai: Configure dataline/FIFO information from dts property
The SAI has multiple successive FIFO registers, but in some use
case the required dataline/FIFOs are not successive, so need
get such information from dts property "fsl,dataline"
fsl,dataline has 3 values for each configuration:
first one means the type: I2S(1) or DSD(2),
second one is dataline mask for 'rx',
third one is dataline mask for 'tx'.
Also set dma peripheral address and TRCE bits according to data lane.
Shengjiu Wang [Fri, 17 Jun 2022 07:44:36 +0000 (15:44 +0800)]
ASoC: dt-bindings: fsl-sai: Add new property to configure dataline
"fsl,dataline" is added to configure the dataline of SAI.
It has 3 value for each configuration, first one means the type:
I2S(1) or PDM(2), second one is dataline mask for 'rx', third one is
dataline mask for 'tx'. for example:
fsl,dataline = <1 0xff 0xff 2 0xff 0x11>,
it means I2S type rx mask is 0xff, tx mask is 0xff, PDM type
rx mask is 0xff, tx mask is 0x11 (dataline 1 and 4 enabled).
Shengjiu Wang [Fri, 17 Jun 2022 07:44:35 +0000 (15:44 +0800)]
ASoC: fsl_sai: Make res a member of struct fsl_sai
The resource info need to be accessed by hw_params()
function for multi fifo case, the start address may
be not the FIFO0. So move it to be a member of
struct fsl_sai.
Shengjiu Wang [Fri, 17 Jun 2022 07:44:34 +0000 (15:44 +0800)]
ASoc: fsl_sai: Add pinctrl operation for PDM and DSD
With DSD format, the pinctrl is different compare with
I2S format, because one dataline only has one channel
data, and the codec always mux the LRCLK pin to DSD
data line, and on i.MX8MQ the BCLK pin can route to
codec on DSD case for the MCLK is too high.
Add pinctrl operation that the pinctrl can be switched
on runtime according to the I2S format or DSD format
Shengjiu Wang [Fri, 17 Jun 2022 07:44:33 +0000 (15:44 +0800)]
ASoC: fsl_sai: Add support for more sample rates
Add support for more sample rates, because PDM format
bitstream has higher sample rates. for example DSD512
format, the bit clock is 22.5792MHz, if the word width
is U8_LE, then the max sample rate is 2822400.
ASoC: cs35l41: Add support for CLSA3541 ACPI device ID
Add support for the CLSA3541 ACPI device ID used on Valve's Steam Deck.
The driver is fully compatible with the indicated hardware, hence no
additional changes are required.
Mark Brown [Fri, 24 Jun 2022 10:58:33 +0000 (11:58 +0100)]
ASoC: Intel: haswell and broadwell boards update
Merge series from Cezary Rojewski <cezary.rojewski@intel.com>:
A number of patches improving overall quality and readability of
haswell.c and broadwell.c source files found in sound/soc/intel/boards.
Both files are first renamed and only then actual changes are being
incrementally added. The respective names are: hsw_rt5640 and bdw_rt286
to match the pattern found in more recent boards.
Most patches bring no functional change - the more impactful patches at
are placed the end. The last patch is removing of FE DAI ops. Given the
existence of platform FE DAI capabilities (either static declaration or
through topology file), this code is redundant.
Charles Keepax [Thu, 23 Jun 2022 10:51:20 +0000 (11:51 +0100)]
ASoC: dapm: Move stereo autodisable check
Tidy up the code a little, rather than repeating the check of
mc->autodisable move the stereo error check to be under the
existing if for mc->autodisable.
Uwe Kleine-König [Wed, 22 Jun 2022 21:06:29 +0000 (23:06 +0200)]
ASoC: topology: KUnit: Followup prototype change of snd_soc_unregister_card()
snd_soc_unregister_card() was recently converted to return void. Only
the first instance was adapted, so convert the remaining ones now to fix
building the topology test.
Reported-by: kernel test robot <lkp@intel.com> Fixes: 1892a991886a ("ASoC: core: Make snd_soc_unregister_card() return void") Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Link: https://lore.kernel.org/r/20220622210629.286487-1-u.kleine-koenig@pengutronix.de Signed-off-by: Mark Brown <broonie@kernel.org>
Cezary Rojewski [Mon, 20 Jun 2022 10:13:58 +0000 (12:13 +0200)]
ASoC: Intel: bdw_rt286: Improve probe() function quality
Declare local 'dev' and make use of it plus dev_get_platdata() to
improve code readability. Relocate few relevant to the function macros
for the exact same read too.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com> Reviewed-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com> Tested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Link: https://lore.kernel.org/r/20220620101402.2684366-14-cezary.rojewski@intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
Cezary Rojewski [Mon, 20 Jun 2022 10:13:57 +0000 (12:13 +0200)]
ASoC: Intel: bdw_rt286: Update file comments
Drop redundant and update valuable comments within the file to increase
readability. This patch also revisits module information and kconfig
help strings.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com> Reviewed-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com> Tested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Link: https://lore.kernel.org/r/20220620101402.2684366-13-cezary.rojewski@intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
Cezary Rojewski [Mon, 20 Jun 2022 10:13:54 +0000 (12:13 +0200)]
ASoC: Intel: bdw_rt286: Reword prefixes of all driver members
Replace ambiguous 'broadwell_rt286_' prefixes in favour of 'card_',
'link_' and other similar strings to clearly state which object given
member implements behavior for.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com> Reviewed-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com> Tested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Link: https://lore.kernel.org/r/20220620101402.2684366-10-cezary.rojewski@intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
Cezary Rojewski [Mon, 20 Jun 2022 10:13:50 +0000 (12:13 +0200)]
ASoC: Intel: hsw_rt5640: Update file comments
Drop redundant and update valuable comments within the file to increase
readability. This patch also revisits module information and kconfig
help strings.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com> Reviewed-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com> Tested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Link: https://lore.kernel.org/r/20220620101402.2684366-6-cezary.rojewski@intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
Cezary Rojewski [Mon, 20 Jun 2022 10:13:47 +0000 (12:13 +0200)]
ASoC: Intel: hsw_rt5640: Reword prefixes of all driver members
Replace ambiguous 'haswell_rt5640_' prefixes in favour of 'card_',
'link_' and other similar strings to clearly state which object given
member implements behavior for.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com> Reviewed-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com> Tested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Link: https://lore.kernel.org/r/20220620101402.2684366-3-cezary.rojewski@intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
Mark Brown [Wed, 22 Jun 2022 16:40:22 +0000 (17:40 +0100)]
ASoC: rockchip: i2s: switch BCLK to GPIO
Merge series from Judy Hsiao <judyhsiao@chromium.org>:
The patches series is to fix the unexpected large DC output
voltage of Max98357a that burns the speakers on the rockchip
platform when BCLK and SD_MODE are ON but LRCLK is OFF.
Chen-Yu Tsai [Tue, 21 Jun 2022 18:57:47 +0000 (02:57 +0800)]
ASoC: rockchip: i2s: Fix crash on missing pinctrl
Commit 44f362c2cc6d ("ASoC: rockchip: i2s: switch BCLK to GPIO") added
pinctrl lookups, but did not skip the lookup if there was no pinctrl
device tied to the I2S controller. As a result, the lookup was done
on an invalid pointer in such cases, causing a kernel panic.
Only do the subsequent pinctrl state lookups and switch if a pinctrl
device was found.
i2s_pinctrl_select_bclk_{on,off} already guard against missing pinctrl
device or pinctrl state, so those two functions aren't touched.
Uwe Kleine-König [Wed, 22 Jun 2022 06:17:39 +0000 (08:17 +0200)]
ASoC: amd: acp: Fix error handling in .remove()
Even in the presence of problems (here: rn_acp_deinit() might fail), it's
important to unregister all resources acquired during .probe() because
even if .remove() returns an error code, the device is removed.
As .remove() is only called after .probe() returned success, platdata
must be valid, so the first check in .remove() can just be dropped.
This is a preparation for making platform remove callbacks return void.
Uwe Kleine-König [Tue, 21 Jun 2022 14:58:34 +0000 (16:58 +0200)]
ASoC: core: Make snd_soc_unregister_card() return void
The function snd_soc_unregister_card() returned 0 unconditionally and most
callers don't care to check the return value. Make it return void and
adapt the callers that didn't ignore the return value before.
This is a preparation for making platform remove callbacks return void.
This patch adds mt8186 dsp document. The dsp is used for Sound Open
Firmware driver node. It includes registers, clocks, memory regions,
and mailbox for dsp.
Tinghan Shen [Wed, 22 Jun 2022 06:22:42 +0000 (14:22 +0800)]
dt-bindings: dsp: mediatek: Use meaningful names for mbox
Rename mbox according to actions instead of 'mbox0' and 'mbox1'.
The 8195 dsp node, which uses this binding, has not yet been added to
the 8195 devicetree.
Judy Hsiao [Sun, 19 Jun 2022 09:53:22 +0000 (09:53 +0000)]
ASoC: rockchip: i2s: switch BCLK to GPIO
We discoverd that the state of BCLK on, LRCLK off and SD_MODE on
may cause the speaker melting issue. Removing LRCLK while BCLK
is present can cause unexpected output behavior including a large
DC output voltage as described in the Max98357a datasheet.
In order to:
1. prevent BCLK from turning on by other component.
2. keep BCLK and LRCLK being present at the same time
This patch switches BCLK to GPIO func before LRCLK output, and
configures BCLK func back during LRCLK is output.
Without this fix, BCLK is turned on 11 ms earlier than LRCK by the
da7219.
With this fix, BCLK is turned on only 0.4 ms earlier than LRCK by
the rockchip codec.
Charles Keepax [Tue, 21 Jun 2022 10:20:41 +0000 (11:20 +0100)]
ASoC: core: Add new SOC_DOUBLE_SX_TLV macro
Currently macros only exist for SX style (implicit sign bit 2's
compliment) volume controls where the volumes for left and right
are in separate registers. Some future Cirrus devices will have
both volumes in the same register, as such add a new macro to
support this.
Shuming Fan [Tue, 21 Jun 2022 09:07:19 +0000 (17:07 +0800)]
ASoC: rt711-sdca: fix kernel NULL pointer dereference when IO error
The initial settings will be written before the codec probe function.
But, the rt711->component doesn't be assigned yet.
If IO error happened during initial settings operations, it will cause the kernel panic.
This patch changed component->dev to slave->dev to fix this issue.
Mark Brown [Mon, 20 Jun 2022 15:39:31 +0000 (16:39 +0100)]
remap: Some fixes for bulk read/write callbacks in regmap_config support
Merge series from Javier Martinez Canillas <javierm@redhat.com>:
This series contains fixes for a few issues found while testing the recent
support for drivers to define bulk read/write callbacks in regmap_config.
I tested this with drivers/gpu/drm/solomon/ssd130x-spi.c, by converting it
to use this new API instead of defining its own regmap bus for bulk write.
Patch #1 and patch #2 are fixes for regresions introduced by that commit
and patch #3 adds regmap_config provided bulk write support to functions
regmap_noinc_write() and regmap_bulk_write(), that were missed.
Sascha Hauer [Fri, 17 Jun 2022 12:01:33 +0000 (14:01 +0200)]
ASoC: fsl_asrc_dma: Use dmaengine_terminate_async()
dmaengine_terminate_all() is deprecated and should no longer be used.
Use dmaengine_terminate_async() instead. This involves no functional change
since both functions do the same.
After dmaengine_terminate_async() dmaengine_synchronize() must be called
to make sure the channel has really stopped before the underlying memory
is freed. This is done implicitly by dma_release_channel() called from
the .hw_free hook.
Judy Hsiao [Wed, 15 Jun 2022 04:56:43 +0000 (04:56 +0000)]
ASoC: rockchip: i2s: switch BCLK to GPIO
We discoverd that the state of BCLK on, LRCLK off and SD_MODE on
may cause the speaker melting issue. Removing LRCLK while BCLK
is present can cause unexpected output behavior including a large
DC output voltage as described in the Max98357a datasheet.
In order to:
1. prevent BCLK from turning on by other component.
2. keep BCLK and LRCLK being present at the same time
This patch switches BCLK to GPIO func before LRCLK output, and
configures BCLK func back during LRCLK is output.
Without this fix, BCLK is turned on 11 ms earlier than LRCK by the
da7219.
With this fix, BCLK is turned on only 0.4 ms earlier than LRCK by
the rockchip codec.
regmap: Wire up regmap_config provided bulk write in missed functions
There are some functions that were missed by commit d77e74561368 ("regmap:
Add bulk read/write callbacks into regmap_config") when support to define
bulk read/write callbacks in regmap_config was introduced.
The regmap_bulk_write() and regmap_noinc_write() functions weren't changed
to use the added map->write instead of the map->bus->write handler.
Also, the regmap_can_raw_write() was not modified to take map->write into
account. So will only return true if a bus with a .write callback is set.
regmap: Make regmap_noinc_read() return -ENOTSUPP if map->read isn't set
Before adding support to define bulk read/write callbacks in regmap_config
by the commit d77e74561368 ("regmap: Add bulk read/write callbacks into
regmap_config"), the regmap_noinc_read() function returned an errno early
a map->bus->read callback wasn't set.
But that commit dropped the check and now a call to _regmap_raw_read() is
attempted even when bulk read operations are not supported. That function
checks for map->read anyways but there's no point to continue if the read
can't succeed.
Also is a fragile assumption to make so is better to make it fail earlier.
regmap: Re-introduce bulk read support check in regmap_bulk_read()
Support for drivers to define bulk read/write callbacks in regmap_config
was introduced by the commit d77e74561368 ("regmap: Add bulk read/write
callbacks into regmap_config"), but this commit wrongly dropped a check
in regmap_bulk_read() to determine whether bulk reads can be done or not.
Before that commit, it was checked if map->bus was set. Now has to check
if a map->read callback has been set.
Mark Brown [Sat, 18 Jun 2022 00:46:19 +0000 (01:46 +0100)]
ASoC: SOF/soundwire: use resume_and_get on component probe
Merge series from Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>:
While testing driver bind/unbind sequences, I stumbled on a corner
case where the SoundWire bus can be suspended before the ASoC card
registration happens. During the registration, register accesses would
then lead to timeouts. This does not happen in regular usages where
the card registration happens within the 3-second time window before
suspend.
Adding a simple pm_runtime_resume_and_get() on component probe solves
the issue, but experiments showed it was too invasive to add at the
ASoC core level, with multiple regressions reported by our CI.
This patchset limits the additional resume to the SOF and SoundWire
codec drivers. An additional patch for the soundwire/intel component
will be sent separately.
Mark Brown [Fri, 17 Jun 2022 23:18:16 +0000 (00:18 +0100)]
ASoC: SOF: Intel: fix resume from hibernate
Merge series from Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>:
The enablement of IMR-based DSP boot helped reduce resume latency, but
unfortunately the context is not saved in S4 and S5 which leads to
multiple reports of boot failures.
This patchset forces a full firmware reload/reboot when resuming from
S4/S5 and restores functionality.
ASoC: SOF: pcm: use pm_resume_and_get() on component probe
Before initiating IPC and/or bus transactions when loading the
topology during a component probe, which happens on card
registration/creation, make sure the device for the SOF driver is
pm_runtime active.
The SOF probe is not necessarily followed by the component probe, such
a timing assumption can be broken in driver bind/unbind tests. This
can be artifially shown if the module for the machine driver is
'blacklisted' and the SOF device becomes pm_runtime_suspended before
manually calling modprobe to register the card.
In an initial experiment, pm_resume_and_get() was called from
soc-component.c, since the current ASoC component model is arguably
missing dependencies between component status and device
status. However this approach proved too invasive and breaks all
existing HDMI playback solutions on Intel platforms.
While this will result in duplication of code, generating pm_runtime
transitions only if strictly required for a given component makes more
sense overall. This patch adds the pm_runtime resume transition for
SOF only.
Fei Shao [Fri, 17 Jun 2022 11:10:04 +0000 (19:10 +0800)]
ASoC: mediatek: mt8186: Fix mutex double unlock in GPIO request
The lockdep mechanism revealed an unbalanced unlocking on MT8186:
[ 2.993966] WARNING: bad unlock balance detected!
[ 2.993978] -------------------------------------
[ 2.993983] kworker/u16:1/10 is trying to release lock (gpio_request_mutex) at:
[ 2.993994] [<ffffffdcd9adebf8>] mt8186_afe_gpio_request+0xf8/0x210
[ 2.994012] but there are no more locks to release!
The cause is that the mutex will be double unlocked if dai is unknown
during GPIO selection, and this patch fixes it.
Stefan Binding [Fri, 17 Jun 2022 15:36:06 +0000 (16:36 +0100)]
ASoC: ops: Fix integer detection for when max possible values > 1
The standard snd_soc_info_volsw() allows a two value control to be
defined as an integer control only if the control name ends in
"Volume". It achieves this by creating a substring if it contains
" Volume", and ensuring this exists at the end of the name. The
volume substring is then used to decide whether the type is a
SNDRV_CTL_ELEM_TYPE_INTEGER or SNDRV_CTL_ELEM_TYPE_BOOLEAN.
However this volume substring is only computed for a two value
control.
This means for controls where there are more than two possible
values, the substring is never created, so in this case the
substring remains NULL, and the condition yields
SNDRV_CTL_ELEM_TYPE_BOOLEAN, even though there are more than 2
possible values.
If there are more than 2 possible values for the control,
then it should always be an integer control.
Fixes: aa2a4b897132 ("ASoC: ops: Fix boolean/integer detection for simple controls") Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com> Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com> Link: https://lore.kernel.org/r/20220617153606.2619457-1-sbinding@opensource.cirrus.com Signed-off-by: Mark Brown <broonie@kernel.org>
The card did not map jack pins to controls, which prevents
PulseAudio/PipeWire from dealing with jack detection. It's likely that
jack detection was only tested with the CRAS server and extensions of
UCM.
Suggested-by: Jaroslav Kysela <perex@perex.cz> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com> Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com> Link: https://lore.kernel.org/r/20220616214055.134943-14-pierre-louis.bossart@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
The card did not map jack pins to controls, which prevents
PulseAudio/PipeWire from dealing with jack detection. It's likely that
jack detection was only tested with the CRAS server and extensions of
UCM.
Suggested-by: Jaroslav Kysela <perex@perex.cz> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com> Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com> Link: https://lore.kernel.org/r/20220616214055.134943-13-pierre-louis.bossart@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
The card did not map jack pins to controls, which prevents
PulseAudio/PipeWire from dealing with jack detection. It's likely that
jack detection was only tested with the CRAS server and extensions of
UCM.
Suggested-by: Jaroslav Kysela <perex@perex.cz> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com> Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com> Link: https://lore.kernel.org/r/20220616214055.134943-12-pierre-louis.bossart@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
The card did not map jack pins to controls, which prevents
PulseAudio/PipeWire from dealing with jack detection. It's likely that
jack detection was only tested with the CRAS server and extensions of
UCM.
Suggested-by: Jaroslav Kysela <perex@perex.cz> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com> Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com> Link: https://lore.kernel.org/r/20220616214055.134943-11-pierre-louis.bossart@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
The card did not map jack pins to controls, which prevents
PulseAudio/PipeWire from dealing with jack detection. It's likely that
jack detection was only tested with the CRAS server and extensions of
UCM.
Suggested-by: Jaroslav Kysela <perex@perex.cz> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com> Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com> Link: https://lore.kernel.org/r/20220616214055.134943-10-pierre-louis.bossart@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
ASoC: Intel: glk_rt5682_max98357a: remap jack pins
The card did not map jack pins to controls, which prevents
PulseAudio/PipeWire from dealing with jack detection. It's likely that
jack detection was only tested with the CRAS server and extensions of
UCM.
Suggested-by: Jaroslav Kysela <perex@perex.cz> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com> Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com> Link: https://lore.kernel.org/r/20220616214055.134943-9-pierre-louis.bossart@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
ASoC: Intel: bxt_da7219_max98357a: remap jack pins
The card did not map jack pins to controls, which prevents
PulseAudio/PipeWire from dealing with jack detection. It's likely that
jack detection was only tested with the CRAS server and extensions of
UCM.
Suggested-by: Jaroslav Kysela <perex@perex.cz> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com> Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com> Link: https://lore.kernel.org/r/20220616214055.134943-8-pierre-louis.bossart@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
ASoC: Intel: kbl_rt5663_rt5514_max98927: remap jack pins
The card did not map jack pins to controls, which prevents
PulseAudio/PipeWire from dealing with jack detection. It's likely that
jack detection was only tested with the CRAS server and extensions of
UCM.
Suggested-by: Jaroslav Kysela <perex@perex.cz> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com> Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com> Link: https://lore.kernel.org/r/20220616214055.134943-7-pierre-louis.bossart@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
The card did not map jack pins to controls, which prevents
PulseAudio/PipeWire from dealing with jack detection. It's likely that
jack detection was only tested with the CRAS server and extensions of
UCM.
Suggested-by: Jaroslav Kysela <perex@perex.cz> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com> Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com> Link: https://lore.kernel.org/r/20220616214055.134943-6-pierre-louis.bossart@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
ASoC: Intel: kbl_da7219_max98357a: remap jack pins
The card did not map jack pins to controls, which prevents
PulseAudio/PipeWire from dealing with jack detection. It's likely that
jack detection was only tested with the CRAS server and extensions of
UCM.
Suggested-by: Jaroslav Kysela <perex@perex.cz> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com> Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com> Link: https://lore.kernel.org/r/20220616214055.134943-5-pierre-louis.bossart@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
The card did not map jack pins to controls, which prevents
PulseAudio/PipeWire from dealing with jack detection. It's likely that
jack detection was only tested with the CRAS server and extensions of
UCM.
Suggested-by: Jaroslav Kysela <perex@perex.cz> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com> Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com> Link: https://lore.kernel.org/r/20220616214055.134943-4-pierre-louis.bossart@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
ASoC: Intel: skl_nau88l25_ssm4567: remap jack pins
The card did not map jack pins to controls, which prevents
PulseAudio/PipeWire from dealing with jack detection. It's likely that
jack detection was only tested with the CRAS server and extensions of
UCM.
Suggested-by: Jaroslav Kysela <perex@perex.cz> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com> Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com> Link: https://lore.kernel.org/r/20220616214055.134943-3-pierre-louis.bossart@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
ASoC: Intel: skl_nau88l25_max98357a: remap jack pins
The card did not map jack pins to controls, which prevents
PulseAudio/PipeWire from dealing with jack detection. It's likely that
jack detection was only tested with the CRAS server and extensions of
UCM.
Suggested-by: Jaroslav Kysela <perex@perex.cz> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com> Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com> Link: https://lore.kernel.org/r/20220616214055.134943-2-pierre-louis.bossart@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
Peter Ujfalusi [Thu, 16 Jun 2022 20:19:53 +0000 (15:19 -0500)]
ASoC: SOF: Intel: hda: Fix compressed stream position tracking
Commit 288fad2f71fa ("ASoC: SOF: Intel: hda: add quirks for HDAudio DMA position information")
modified the PCM path only, but left the compressed data patch using an
obsolete option.
Move the functionality in a helper that can be called for both PCM and
compressed data.
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Fixes: 288fad2f71fa ("ASoC: SOF: Intel: hda: add quirks for HDAudio DMA position information") Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Link: https://lore.kernel.org/r/20220616201953.130876-1-pierre-louis.bossart@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
ASoC: SOF: Intel: disable IMR boot when resuming from ACPI S4 and S5 states
The IMR was assumed to be preserved when suspending to S4 and S5
states, but community reports invalidate that assumption, the hardware
seems to be powered off and the IMR memory content cleared.
Make sure regular boot with firmware download is used for S4 and S5.
ASoC: SOF: pm: add definitions for S4 and S5 states
We currently don't have a means to differentiate between S3, S4 and
S5. Add definitions so that we have select different code paths
depending on the target state in follow-up patches.
Colin Ian King [Tue, 14 Jun 2022 18:38:09 +0000 (19:38 +0100)]
ASoC: Intel: Skylake: remove redundant re-assignments to pointer array
There are two occurrences where the pointer array is being assigned a value
that is never read, the pointer gets updated in the next iteration of a
loop. These assignments are redundant and can be removed.
Cleans up clang scan-build warnings:
sound/soc/intel/skylake/skl-topology.c:2953:3: warning: Value stored to
'array' is never read [deadcode.DeadStores]
sound/soc/intel/skylake/skl-topology.c:3602:3: warning: Value stored to
'array' is never read [deadcode.DeadStores]
Dan Carpenter [Thu, 16 Jun 2022 04:31:09 +0000 (07:31 +0300)]
ASoC: SOF: ipc4-topology: Fix error code in sof_ipc4_volume_put()
The sof_ipc4_volume_put() function returns type bool so returning
-ENOENT means returning true. Return false instead.
Fixes: 955e84fc0b6d ("ASoC: SOF: ipc4-topology: Add control IO ops") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com> Link: https://lore.kernel.org/r/YqqyDU5BhOzpRjco@kili Signed-off-by: Mark Brown <broonie@kernel.org>
Mark Brown [Wed, 15 Jun 2022 17:05:36 +0000 (18:05 +0100)]
ASoC: Add regmap_field helpers for simple bit operations
Merge series from Li Chen <lchen.firstlove@zohomail.com>
This series proposes to add simple bit operations for setting, clearing
and testing specific bits with regmap_field and uses them in one of the
sunxi drivers.
Mark Brown [Wed, 15 Jun 2022 12:41:28 +0000 (13:41 +0100)]
ASoC: SOF: Intel: Add support for MeteorLake
Merge series from Bard Liao <yung-chuan.liao@linux.intel.com>:
Add platform abstraction for the Meteor Lake platform.
This platform has significant differences compared to the TGL/ADL
generation: it relies on new hardware using the code name 'ACE' and
only supports the INTEL_IPC4 protocol and firmware architecture based
on the Zephyr RTOS