Kai-Heng Feng [Thu, 25 Jan 2024 06:50:28 +0000 (14:50 +0800)]
Bluetooth: Enforce validation on max value of connection interval
Right now Linux BT stack cannot pass test case "GAP/CONN/CPUP/BV-05-C
'Connection Parameter Update Procedure Invalid Parameters Central
Responder'" in Bluetooth Test Suite revision GAP.TS.p44. [0]
That was revoled by commit c49a8682fc5d ("Bluetooth: validate BLE
connection interval updates"), but later got reverted due to devices
like keyboards and mice may require low connection interval.
So only validate the max value connection interval to pass the Test
Suite, and let devices to request low connection interval if needed.
Bluetooth: hci_event: Fix handling of HCI_EV_IO_CAPA_REQUEST
If we received HCI_EV_IO_CAPA_REQUEST while
HCI_OP_READ_REMOTE_EXT_FEATURES is yet to be responded assume the remote
does support SSP since otherwise this event shouldn't be generated.
Frédéric Danis [Mon, 22 Jan 2024 16:59:55 +0000 (17:59 +0100)]
Bluetooth: mgmt: Fix limited discoverable off timeout
LIMITED_DISCOVERABLE flag is not reset from Class of Device and
advertisement on limited discoverable timeout. This prevents to pass PTS
test GAP/DISC/LIMM/BV-02-C
Calling set_discoverable_sync as when the limited discovery is set
correctly update the Class of Device and advertisement.
Signed-off-by: Frédéric Danis <frederic.danis@collabora.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Zijun Hu [Tue, 9 Jan 2024 11:03:23 +0000 (19:03 +0800)]
Bluetooth: hci_event: Fix wrongly recorded wakeup BD_ADDR
hci_store_wake_reason() wrongly parses event HCI_Connection_Request
as HCI_Connection_Complete and HCI_Connection_Complete as
HCI_Connection_Request, so causes recording wakeup BD_ADDR error and
potential stability issue, fix it by using the correct field.
Fixes: 2f20216c1d6f ("Bluetooth: Emit controller suspend and resume events") Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Yuxuan Hu [Wed, 3 Jan 2024 09:10:43 +0000 (17:10 +0800)]
Bluetooth: rfcomm: Fix null-ptr-deref in rfcomm_check_security
During our fuzz testing of the connection and disconnection process at the
RFCOMM layer, we discovered this bug. By comparing the packets from a
normal connection and disconnection process with the testcase that
triggered a KASAN report. We analyzed the cause of this bug as follows:
1. In the packets captured during a normal connection, the host sends a
`Read Encryption Key Size` type of `HCI_CMD` packet
(Command Opcode: 0x1408) to the controller to inquire the length of
encryption key.After receiving this packet, the controller immediately
replies with a Command Completepacket (Event Code: 0x0e) to return the
Encryption Key Size.
2. In our fuzz test case, the timing of the controller's response to this
packet was delayed to an unexpected point: after the RFCOMM and L2CAP
layers had disconnected but before the HCI layer had disconnected.
3. After receiving the Encryption Key Size Response at the time described
in point 2, the host still called the rfcomm_check_security function.
However, by this time `struct l2cap_conn *conn = l2cap_pi(sk)->chan->conn;`
had already been released, and when the function executed
`return hci_conn_security(conn->hcon, d->sec_level, auth_type, d->out);`,
specifically when accessing `conn->hcon`, a null-ptr-deref error occurred.
To fix this bug, check if `sk->sk_state` is BT_CLOSED before calling
rfcomm_recv_frame in rfcomm_process_rx.
Signed-off-by: Yuxuan Hu <20373622@buaa.edu.cn> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Bluetooth: hci_sync: Fix accept_list when attempting to suspend
During suspend, only wakeable devices can be in acceptlist, so if the
device was previously added it needs to be removed otherwise the device
can end up waking up the system prematurely.
Fixes: 3b42055388c3 ("Bluetooth: hci_sync: Fix attempting to suspend with unfiltered passive scan") Signed-off-by: Clancy Shang <clancy.shang@quectel.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Ying Hsu [Thu, 4 Jan 2024 11:56:32 +0000 (11:56 +0000)]
Bluetooth: Avoid potential use-after-free in hci_error_reset
While handling the HCI_EV_HARDWARE_ERROR event, if the underlying
BT controller is not responding, the GPIO reset mechanism would
free the hci_dev and lead to a use-after-free in hci_error_reset.
Here's the call trace observed on a ChromeOS device with Intel AX201:
queue_work_on+0x3e/0x6c
__hci_cmd_sync_sk+0x2ee/0x4c0 [bluetooth <HASH:3b4a6>]
? init_wait_entry+0x31/0x31
__hci_cmd_sync+0x16/0x20 [bluetooth <HASH:3b4a 6>]
hci_error_reset+0x4f/0xa4 [bluetooth <HASH:3b4a 6>]
process_one_work+0x1d8/0x33f
worker_thread+0x21b/0x373
kthread+0x13a/0x152
? pr_cont_work+0x54/0x54
? kthread_blkcg+0x31/0x31
ret_from_fork+0x1f/0x30
This patch holds the reference count on the hci_dev while processing
a HCI_EV_HARDWARE_ERROR event to avoid potential crash.
Fixes: c7741d16a57c ("Bluetooth: Perform a power cycle when receiving hardware error event") Signed-off-by: Ying Hsu <yinghsu@chromium.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Jonas Dreßler [Tue, 2 Jan 2024 18:08:08 +0000 (19:08 +0100)]
Bluetooth: hci_sync: Check the correct flag before starting a scan
There's a very confusing mistake in the code starting a HCI inquiry: We're
calling hci_dev_test_flag() to test for HCI_INQUIRY, but hci_dev_test_flag()
checks hdev->dev_flags instead of hdev->flags. HCI_INQUIRY is a bit that's
set on hdev->flags, not on hdev->dev_flags though.
HCI_INQUIRY equals the integer 7, and in hdev->dev_flags, 7 means
HCI_BONDABLE, so we were actually checking for HCI_BONDABLE here.
The mistake is only present in the synchronous code for starting an inquiry,
not in the async one. Also devices are typically bondable while doing an
inquiry, so that might be the reason why nobody noticed it so far.
Fixes: abfeea476c68 ("Bluetooth: hci_sync: Convert MGMT_OP_START_DISCOVERY") Signed-off-by: Jonas Dreßler <verdre@v0yd.nl> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Johan Hovold [Wed, 27 Dec 2023 10:10:03 +0000 (11:10 +0100)]
Bluetooth: hci_bcm4377: do not mark valid bd_addr as invalid
A recent commit restored the original (and still documented) semantics
for the HCI_QUIRK_USE_BDADDR_PROPERTY quirk so that the device address
is considered invalid unless an address is provided by firmware.
This specifically means that this flag must only be set for devices with
invalid addresses, but the Broadcom BCM4377 driver has so far been
setting this flag unconditionally.
Fortunately the driver already checks for invalid addresses during setup
and sets the HCI_QUIRK_INVALID_BDADDR flag, which can simply be replaced
with HCI_QUIRK_USE_BDADDR_PROPERTY to indicate that the default address
is invalid but can be overridden by firmware (long term, this should
probably just always be allowed).
Fixes: 6945795bc81a ("Bluetooth: fix use-bdaddr-property quirk") Cc: stable@vger.kernel.org # 6.5 Reported-by: Felix Zhang <mrman@mrman314.tech> Link: https://lore.kernel.org/r/77419ffacc5b4875e920e038332575a2a5bff29f.camel@mrman314.tech/ Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Reported-by: Felix Zhang <mrman@mrman314.tech> Reviewed-by: Neal Gompa <neal@gompa.dev> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Jakub Raczynski [Mon, 26 Feb 2024 16:42:32 +0000 (17:42 +0100)]
stmmac: Clear variable when destroying workqueue
Currently when suspending driver and stopping workqueue it is checked whether
workqueue is not NULL and if so, it is destroyed.
Function destroy_workqueue() does drain queue and does clear variable, but
it does not set workqueue variable to NULL. This can cause kernel/module
panic if code attempts to clear workqueue that was not initialized.
This scenario is possible when resuming suspended driver in stmmac_resume(),
because there is no handling for failed stmmac_hw_setup(),
which can fail and return if DMA engine has failed to initialize,
and workqueue is initialized after DMA engine.
Should DMA engine fail to initialize, resume will proceed normally,
but interface won't work and TX queue will eventually timeout,
causing 'Reset adapter' error.
This then does destroy workqueue during reset process.
And since workqueue is initialized after DMA engine and can be skipped,
it will cause kernel/module panic.
To secure against this possible crash, set workqueue variable to NULL when
destroying workqueue.
Log/backtrace from crash goes as follows:
[88.031977]------------[ cut here ]------------
[88.031985]NETDEV WATCHDOG: eth0 (sxgmac): transmit queue 1 timed out
[88.032017]WARNING: CPU: 0 PID: 0 at net/sched/sch_generic.c:477 dev_watchdog+0x390/0x398
<Skipping backtrace for watchdog timeout>
[88.032251]---[ end trace e70de432e4d5c2c0 ]---
[88.032282]sxgmac 16d88000.ethernet eth0: Reset adapter.
[88.036359]------------[ cut here ]------------
[88.036519]Call trace:
[88.036523] flush_workqueue+0x3e4/0x430
[88.036528] drain_workqueue+0xc4/0x160
[88.036533] destroy_workqueue+0x40/0x270
[88.036537] stmmac_fpe_stop_wq+0x4c/0x70
[88.036541] stmmac_release+0x278/0x280
[88.036546] __dev_close_many+0xcc/0x158
[88.036551] dev_close_many+0xbc/0x190
[88.036555] dev_close.part.0+0x70/0xc0
[88.036560] dev_close+0x24/0x30
[88.036564] stmmac_service_task+0x110/0x140
[88.036569] process_one_work+0x1d8/0x4a0
[88.036573] worker_thread+0x54/0x408
[88.036578] kthread+0x164/0x170
[88.036583] ret_from_fork+0x10/0x20
[88.036588]---[ end trace e70de432e4d5c2c1 ]---
[88.036597]Unable to handle kernel NULL pointer dereference at virtual address 0000000000000004
Fixes: 5a5586112b929 ("net: stmmac: support FPE link partner hand-shaking procedure") Signed-off-by: Jakub Raczynski <j.raczynski@samsung.com> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Randy Dunlap [Mon, 26 Feb 2024 07:48:20 +0000 (23:48 -0800)]
net: ethernet: adi: move PHYLIB from vendor to driver symbol
In a previous patch I added "select PHYLIB" at the wrong place for the
ADIN1110 driver symbol, so move it to its correct place under the
ADIN1110 kconfig symbol.
Fixes: a9f80df4f514 ("net: ethernet: adi: requires PHYLIB support") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Reported-by: Michal Kubecek <mkubecek@suse.cz> Closes: https://lore.kernel.org/lkml/77012b38-4b49-47f4-9a88-d773d52909ad@infradead.org/T/#m8ba397484738711edc0ad607b2c63ca02244e3c3 Cc: Lennart Franzen <lennart@lfdomain.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Eric Dumazet <edumazet@google.com> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Paolo Abeni <pabeni@redhat.com> Cc: netdev@vger.kernel.org Cc: Nuno Sa <nuno.sa@analog.com> Tested-by: Michal Kubecek <mkubecek@suse.cz> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Wed, 28 Feb 2024 03:19:16 +0000 (19:19 -0800)]
Merge tag 'wireless-2024-02-27' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless
Kalle Valo says:
====================
wireless fixes for v6.8-rc7
Few remaining fixes, hopefully the last wireless pull request to v6.8.
Two fixes to the stack and two to iwlwifi but no high priority fixes
this time.
* tag 'wireless-2024-02-27' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless:
wifi: mac80211: only call drv_sta_rc_update for uploaded stations
MAINTAINERS: wifi: Add N: ath1*k entries to match .yaml files
MAINTAINERS: wifi: update Jeff Johnson e-mail address
wifi: iwlwifi: mvm: fix the TXF mapping for BZ devices
wifi: iwlwifi: mvm: ensure offloading TID queue exists
wifi: nl80211: reject iftype change with mesh ID change
====================
Justin Iurman [Mon, 26 Feb 2024 12:49:21 +0000 (13:49 +0100)]
uapi: in6: replace temporary label with rfc9486
Not really a fix per se, but IPV6_TLV_IOAM is still tagged as "TEMPORARY
IANA allocation for IOAM", while RFC 9486 is available for some time
now. Just update the reference.
Fixes: 9ee11f0fff20 ("ipv6: ioam: Data plane support for Pre-allocated Trace") Signed-off-by: Justin Iurman <justin.iurman@uliege.be> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/20240226124921.9097-1-justin.iurman@uliege.be Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The program counter indicates xsk_tx_metadata_complete(). It works on
compl->tx_timestamp, which is not set by xsk_tx_metadata_to_compl() due to
missing meta data. Therefore, call xsk_tx_metadata_complete() only when
meta data is actually used.
Tested on imx93 without XDP, with XDP and with XDP/ZC.
Javier Carrasco [Sat, 24 Feb 2024 23:20:06 +0000 (00:20 +0100)]
net: usb: dm9601: fix wrong return value in dm9601_mdio_read
The MII code does not check the return value of mdio_read (among
others), and therefore no error code should be sent. A previous fix to
the use of an uninitialized variable propagates negative error codes,
that might lead to wrong operations by the MII library.
An example of such issues is the use of mii_nway_restart by the dm9601
driver. The mii_nway_restart function does not check the value returned
by mdio_read, which in this case might be a negative number which could
contain the exact bit the function checks (BMCR_ANENABLE = 0x1000).
Return zero in case of error, as it is common practice in users of
mdio_read to avoid wrong uses of the return value.
Fixes: 8f8abb863fa5 ("net: usb: dm9601: fix uninitialized variable use in dm9601_mdio_read") Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com> Reviewed-by: Simon Horman <horms@kernel.org> Reviewed-by: Peter Korsgaard <peter@korsgaard.com> Link: https://lore.kernel.org/r/20240225-dm9601_ret_err-v1-1-02c1d959ea59@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Fri, 23 Feb 2024 23:59:08 +0000 (15:59 -0800)]
veth: try harder when allocating queue memory
struct veth_rq is pretty large, 832B total without debug
options enabled. Since commit under Fixes we try to pre-allocate
enough queues for every possible CPU. Miao Wang reports that
this may lead to order-5 allocations which will fail in production.
Let the allocation fallback to vmalloc() and try harder.
These are the same flags we pass to netdev queue allocation.
Shannon Nelson [Fri, 23 Feb 2024 22:27:42 +0000 (14:27 -0800)]
ionic: restore netdev feature bits after reset
When rebuilding the lif after an FLR, be sure to restore the
current netdev features, not do the usual first time feature
init. This prevents losing user changes to things like TSO
or vlan tagging states.
Fixes: 45b84188a0a4 ("ionic: keep filters across FLR") Reviewed-by: Brett Creeley <brett.creeley@amd.com> Signed-off-by: Shannon Nelson <shannon.nelson@amd.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Shannon Nelson [Fri, 23 Feb 2024 22:27:41 +0000 (14:27 -0800)]
ionic: check cmd_regs before copying in or out
Since we now have potential cases of NULL cmd_regs and info_regs
during a reset recovery, and left NULL if a reset recovery has
failed, we need to check that they exist before we use them.
Most of the cases were covered in the original patch where we
verify before doing the ioreadb() for health or cmd status.
However, we need to protect a few uses of io mem that could
be hit in error recovery or asynchronous threads calls as well
(e.g. ethtool or devlink handlers).
Fixes: 219e183272b4 ("ionic: no fw read when PCI reset failed") Reviewed-by: Brett Creeley <brett.creeley@amd.com> Signed-off-by: Shannon Nelson <shannon.nelson@amd.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Shannon Nelson [Fri, 23 Feb 2024 22:27:40 +0000 (14:27 -0800)]
ionic: check before releasing pci regions
AER recovery handler can trigger a PCI Reset after tearing
down the device setup in the error detection handler. The PCI
Reset handler will also attempt to tear down the device setup,
and this second tear down needs to know that it doesn't need
to call pci_release_regions() a second time. We can clear
num_bars on tear down and use that to decide later if we need
to clear the resources. This prevents a harmless but disturbing
warning message
resource: Trying to free nonexistent resource <0xXXXXXXXXXX-0xXXXXXXXXXX>
Fixes: c3a910e1c47a ("ionic: fill out pci error handlers") Reviewed-by: Brett Creeley <brett.creeley@amd.com> Signed-off-by: Shannon Nelson <shannon.nelson@amd.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Jakub Kicinski [Tue, 27 Feb 2024 02:42:04 +0000 (18:42 -0800)]
Merge branch 'mptcp-more-misc-fixes-for-v6-8'
Matthieu Baerts says:
====================
mptcp: more misc. fixes for v6.8
This series includes 6 types of fixes:
- Patch 1 fixes v4 mapped in v6 addresses support for the userspace PM,
when asking to delete a subflow. It was done everywhere else, but not
there. Patch 2 validates the modification, thanks to a subtest in
mptcp_join.sh. These patches can be backported up to v5.19.
- Patch 3 is a small fix for a recent bug-fix patch, just to avoid
printing an irrelevant warning (pr_warn()) once. It can be backported
up to v5.6, alongside the bug-fix that has been introduced in the
v6.8-rc5.
- Patches 4 to 6 are fixes for bugs found by Paolo while working on
TCP_NOTSENT_LOWAT support for MPTCP. These fixes can improve the
performances in some cases. Patches can be backported up to v5.6,
v5.11 and v6.7 respectively.
- Patch 7 makes sure 'ss -M' is available when starting MPTCP Join
selftest as it is required for some subtests since v5.18.
- Patch 8 fixes a possible double-free on socket dismantle. The issue
always existed, but was unnoticed because it was not causing any
problem so far. This fix can be backported up to v5.6.
- Patch 9 is a fix for a very recent patch causing lockdep warnings in
subflow diag. The patch causing the regression -- which fixes another
issue present since v5.7 -- should be part of the future v6.8-rc6.
Patch 10 validates the modification, thanks to a new subtest in
diag.sh.
====================
Paolo Abeni [Fri, 23 Feb 2024 16:14:20 +0000 (17:14 +0100)]
selftests: mptcp: explicitly trigger the listener diag code-path
The mptcp diag interface already experienced a few locking bugs
that lockdep and appropriate coverage have detected in advance.
Let's add a test-case triggering the relevant code path, to prevent
similar issues in the future.
Be careful to cope with very slow environments.
Note that we don't need an explicit timeout on the mptcp_connect
subprocess to cope with eventual bug/hang-up as the final cleanup
terminating the child processes will take care of that.
As noted by Eric we can break the lock dependency chain avoid
dumping any extended info for the mptcp subflow listener:
nothing actually useful is presented there.
Fixes: b8adb69a7d29 ("mptcp: fix lockless access in subflow ULP diag") Cc: stable@vger.kernel.org Reported-by: Eric Dumazet <edumazet@google.com> Closes: https://lore.kernel.org/netdev/CANn89iJ=Oecw6OZDwmSYc9HJKQ_G32uN11L+oUcMu+TOD5Xiaw@mail.gmail.com/ Suggested-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org> Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org> Link: https://lore.kernel.org/r/20240223-upstream-net-20240223-misc-fixes-v1-9-162e87e48497@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Davide Caratti [Fri, 23 Feb 2024 16:14:18 +0000 (17:14 +0100)]
mptcp: fix double-free on socket dismantle
when MPTCP server accepts an incoming connection, it clones its listener
socket. However, the pointer to 'inet_opt' for the new socket has the same
value as the original one: as a consequence, on program exit it's possible
to observe the following splat:
BUG: KASAN: double-free in inet_sock_destruct+0x54f/0x8b0
Free of addr ffff888485950880 by task swapper/25/0
The buggy address belongs to the object at ffff888485950880
which belongs to the cache kmalloc-64 of size 64
The buggy address is located 0 bytes inside of
64-byte region [ffff888485950880, ffff8884859508c0)
Memory state around the buggy address: ffff888485950780: fa fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc ffff888485950800: fa fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
>ffff888485950880: fa fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
^ ffff888485950900: fa fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc ffff888485950980: 00 00 00 00 00 01 fc fc fc fc fc fc fc fc fc fc
Something similar (a refcount underflow) happens with CALIPSO/IPv6. Fix
this by duplicating IP / IPv6 options after clone, so that
ip{,6}_sock_destruct() doesn't end up freeing the same memory area twice.
Fixes: cf7da0d66cc1 ("mptcp: Create SUBFLOW socket for incoming connections") Cc: stable@vger.kernel.org Signed-off-by: Davide Caratti <dcaratti@redhat.com> Reviewed-by: Mat Martineau <martineau@kernel.org> Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org> Link: https://lore.kernel.org/r/20240223-upstream-net-20240223-misc-fixes-v1-8-162e87e48497@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Paolo Abeni [Fri, 23 Feb 2024 16:14:16 +0000 (17:14 +0100)]
mptcp: fix potential wake-up event loss
After the blamed commit below, the send buffer auto-tuning can
happen after that the mptcp_propagate_sndbuf() completes - via
the delegated action infrastructure.
We must check for write space even after such change or we risk
missing the wake-up event.
Fixes: 8005184fd1ca ("mptcp: refactor sndbuf auto-tuning") Cc: stable@vger.kernel.org Signed-off-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: Mat Martineau <martineau@kernel.org> Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org> Link: https://lore.kernel.org/r/20240223-upstream-net-20240223-misc-fixes-v1-6-162e87e48497@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Paolo Abeni [Fri, 23 Feb 2024 16:14:14 +0000 (17:14 +0100)]
mptcp: push at DSS boundaries
when inserting not contiguous data in the subflow write queue,
the protocol creates a new skb and prevent the TCP stack from
merging it later with already queued skbs by setting the EOR marker.
Still no push flag is explicitly set at the end of previous GSO
packet, making the aggregation on the receiver side sub-optimal -
and packetdrill self-tests less predictable.
Explicitly mark the end of not contiguous DSS with the push flag.
Fixes: 6d0060f600ad ("mptcp: Write MPTCP DSS headers to outgoing data packets") Cc: stable@vger.kernel.org Signed-off-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: Mat Martineau <martineau@kernel.org> Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org> Link: https://lore.kernel.org/r/20240223-upstream-net-20240223-misc-fixes-v1-4-162e87e48497@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After the 'Fixes' commit mentioned below, the client side might print
the following warning once when a subflow is fully established at the
reception of any valid additional ack:
MPTCP: bogus mpc option on established client sk
That's a normal situation, and no warning should be printed for that. We
can then skip the check when the label is used.
Fixes: e4a0fa47e816 ("mptcp: corner case locking for rx path fields initialization") Cc: stable@vger.kernel.org Suggested-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: Mat Martineau <martineau@kernel.org> Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org> Link: https://lore.kernel.org/r/20240223-upstream-net-20240223-misc-fixes-v1-3-162e87e48497@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Geliang Tang [Fri, 23 Feb 2024 16:14:12 +0000 (17:14 +0100)]
selftests: mptcp: rm subflow with v4/v4mapped addr
Now both a v4 address and a v4-mapped address are supported when
destroying a userspace pm subflow, this patch adds a second subflow
to "userspace pm add & remove address" test, and two subflows could
be removed two different ways, one with the v4mapped and one with v4.
That's because on the server side, the family is set to AF_INET6 and the
v4 address is mapped in a v6 one.
This patch fixes this issue. In mptcp_pm_nl_subflow_destroy_doit(), before
checking local address family with remote address family, map an IPv4
address to an IPv6 address if the pair is a v4-mapped address.
Oleksij Rempel [Thu, 22 Feb 2024 12:38:38 +0000 (13:38 +0100)]
lan78xx: enable auto speed configuration for LAN7850 if no EEPROM is detected
Same as LAN7800, LAN7850 can be used without EEPROM. If EEPROM is not
present or not flashed, LAN7850 will fail to sync the speed detected by the PHY
with the MAC. In case link speed is 100Mbit, it will accidentally work,
otherwise no data can be transferred.
Better way would be to implement link_up callback, or set auto speed
configuration unconditionally. But this changes would be more intrusive.
So, for now, set it only if no EEPROM is found.
Eric Dumazet [Thu, 22 Feb 2024 12:17:47 +0000 (12:17 +0000)]
ipv6: fix potential "struct net" leak in inet6_rtm_getaddr()
It seems that if userspace provides a correct IFA_TARGET_NETNSID value
but no IFA_ADDRESS and IFA_LOCAL attributes, inet6_rtm_getaddr()
returns -EINVAL with an elevated "struct net" refcount.
Fixes: 6ecf4c37eb3e ("ipv6: enable IFA_TARGET_NETNSID for RTM_GETADDR") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Christian Brauner <brauner@kernel.org> Cc: David Ahern <dsahern@kernel.org> Reviewed-by: David Ahern <dsahern@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Wed, 21 Feb 2024 23:12:11 +0000 (15:12 -0800)]
selftests: net: veth: test syncing GRO and XDP state while device is down
Test that we keep GRO flag in sync when XDP is disabled while
the device is closed.
Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Wed, 21 Feb 2024 23:12:10 +0000 (15:12 -0800)]
net: veth: clear GRO when clearing XDP even when down
veth sets NETIF_F_GRO automatically when XDP is enabled,
because both features use the same NAPI machinery.
The logic to clear NETIF_F_GRO sits in veth_disable_xdp() which
is called both on ndo_stop and when XDP is turned off.
To avoid the flag from being cleared when the device is brought
down, the clearing is skipped when IFF_UP is not set.
Bringing the device down should indeed not modify its features.
Unfortunately, this means that clearing is also skipped when
XDP is disabled _while_ the device is down. And there's nothing
on the open path to bring the device features back into sync.
IOW if user enables XDP, disables it and then brings the device
up we'll end up with a stray GRO flag set but no NAPI instances.
We don't depend on the GRO flag on the datapath, so the datapath
won't crash. We will crash (or hang), however, next time features
are sync'ed (either by user via ethtool or peer changing its config).
The GRO flag will go away, and veth will try to disable the NAPIs.
But the open path never created them since XDP was off, the GRO flag
was a stray. If NAPI was initialized before we'll hang in napi_disable().
If it never was we'll crash trying to stop uninitialized hrtimer.
Move the GRO flag updates to the XDP enable / disable paths,
instead of mixing them with the ndo_open / ndo_close paths.
Fixes: d3256efd8e8b ("veth: allow enabling NAPI even without XDP") Reported-by: Thomas Gleixner <tglx@linutronix.de> Reported-by: syzbot+039399a9b96297ddedca@syzkaller.appspotmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Geoff Levand [Wed, 21 Feb 2024 02:27:29 +0000 (11:27 +0900)]
ps3/gelic: Fix SKB allocation
Commit 3ce4f9c3fbb3 ("net/ps3_gelic_net: Add gelic_descr structures") of
6.8-rc1 had a copy-and-paste error where the pointer that holds the
allocated SKB (struct gelic_descr.skb) was set to NULL after the SKB was
allocated. This resulted in a kernel panic when the SKB pointer was
accessed.
This fix moves the initialization of the gelic_descr to before the SKB
is allocated.
Reported-by: sambat goson <sombat3960@gmail.com> Fixes: 3ce4f9c3fbb3 ("net/ps3_gelic_net: Add gelic_descr structures") Signed-off-by: Geoff Levand <geoff@infradead.org> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Tue, 20 Feb 2024 22:34:42 +0000 (00:34 +0200)]
net: dpaa: fman_memac: accept phy-interface-type = "10gbase-r" in the device tree
Since commit 5d93cfcf7360 ("net: dpaa: Convert to phylink"), we support
the "10gbase-r" phy-mode through a driver-based conversion of "xgmii",
but we still don't actually support it when the device tree specifies
"10gbase-r" proper.
This is because boards such as LS1046A-RDB do not define pcs-handle-names
(for whatever reason) in the ethernet@f0000 device tree node, and the
code enters through this code path:
err = of_property_match_string(mac_node, "pcs-handle-names", "xfi");
// code takes neither branch and falls through
if (err >= 0) {
(...)
} else if (err != -EINVAL && err != -ENODATA) {
goto _return_fm_mac_free;
}
(...)
/* For compatibility, if pcs-handle-names is missing, we assume this
* phy is the first one in pcsphy-handle
*/
err = of_property_match_string(mac_node, "pcs-handle-names", "sgmii");
if (err == -EINVAL || err == -ENODATA)
pcs = memac_pcs_create(mac_node, 0); // code takes this branch
else if (err < 0)
goto _return_fm_mac_free;
else
pcs = memac_pcs_create(mac_node, err);
// A default PCS is created and saved in "pcs"
// This determination fails and mistakenly saves the default PCS
// memac->sgmii_pcs instead of memac->xfi_pcs, because at this
// stage, mac_dev->phy_if == PHY_INTERFACE_MODE_10GBASER.
if (err && mac_dev->phy_if == PHY_INTERFACE_MODE_XGMII)
memac->xfi_pcs = pcs;
else
memac->sgmii_pcs = pcs;
In other words, in the absence of pcs-handle-names, the default
xfi_pcs assignment logic only works when in the device tree we have
PHY_INTERFACE_MODE_XGMII.
By reversing the order between the fallback xfi_pcs assignment and the
"xgmii" overwrite with "10gbase-r", we are able to support both values
in the device tree, with identical behavior.
Currently, it is impossible to make the s/xgmii/10gbase-r/ device tree
conversion, because it would break forward compatibility (new device
tree with old kernel). The only way to modify existing device trees to
phy-interface-mode = "10gbase-r" is to fix stable kernels to accept this
value and handle it properly.
One reason why the conversion is desirable is because with pre-phylink
kernels, the Aquantia PHY driver used to warn about the improper use
of PHY_INTERFACE_MODE_XGMII [1]. It is best to have a single (latest)
device tree that works with all supported stable kernel versions.
Note that the blamed commit does not constitute a regression per se.
Older stable kernels like 6.1 still do not work with "10gbase-r", but
for a different reason. That is a battle for another time.
Fixes: 5d93cfcf7360 ("net: dpaa: Convert to phylink") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Sean Anderson <sean.anderson@seco.com> Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Felix Fietkau [Wed, 21 Feb 2024 14:05:35 +0000 (15:05 +0100)]
wifi: mac80211: only call drv_sta_rc_update for uploaded stations
When a station has not been uploaded yet, receiving SMPS or channel width
notification action frames can lead to rate_control_rate_update calling
drv_sta_rc_update with uninitialized driver private data.
Fix this by adding a missing check for sta->uploaded.
Jeremy Kerr [Tue, 20 Feb 2024 08:10:53 +0000 (16:10 +0800)]
net: mctp: take ownership of skb in mctp_local_output
Currently, mctp_local_output only takes ownership of skb on success, and
we may leak an skb if mctp_local_output fails in specific states; the
skb ownership isn't transferred until the actual output routing occurs.
Instead, make mctp_local_output free the skb on all error paths up to
the route action, so it always consumes the passed skb.
Jakub Kicinski [Fri, 23 Feb 2024 03:19:37 +0000 (19:19 -0800)]
Merge branch '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2024-02-20 (ice)
This series contains updates to ice driver only.
Yochai sets parent device to properly reflect connection state between
source DPLL and output pin.
Arkadiusz fixes additional issues related to DPLL; proper reporting of
phase_adjust value and preventing use/access of data while resetting.
Amritha resolves ASSERT_RTNL() being triggered on certain reset/rebuild
flows.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
ice: Fix ASSERT_RTNL() warning during certain scenarios
ice: fix pin phase adjust updates on PF reset
ice: fix dpll periodic work data updates on PF reset
ice: fix dpll and dpll_pin data access on PF reset
ice: fix dpll input pin phase_adjust value updates
ice: fix connection state of DPLL and out pin
====================
The splat occurs because skb->data points past skb->head allocated area.
This is because neigh layer does:
__skb_pull(skb, skb_network_offset(skb));
... but skb_network_offset() returns a negative offset and __skb_pull()
arg is unsigned. IOW, we skb->data gets "adjusted" by a huge value.
The negative value is returned because skb->head and skb->data distance is
more than 64k and skb->network_header (u16) has wrapped around.
The bug is in the ip_tunnel infrastructure, which can cause
dev->needed_headroom to increment ad infinitum.
The syzkaller reproducer consists of packets getting routed via a gre
tunnel, and route of gre encapsulated packets pointing at another (ipip)
tunnel. The ipip encapsulation finds gre0 as next output device.
This results in the following pattern:
1). First packet is to be sent out via gre0.
Route lookup found an output device, ipip0.
2).
ip_tunnel_xmit for gre0 bumps gre0->needed_headroom based on the future
output device, rt.dev->needed_headroom (ipip0).
3).
ip output / start_xmit moves skb on to ipip0. which runs the same
code path again (xmit recursion).
4).
Routing step for the post-gre0-encap packet finds gre0 as output device
to use for ipip0 encapsulated packet.
tunl0->needed_headroom is then incremented based on the (already bumped)
gre0 device headroom.
This repeats for every future packet:
gre0->needed_headroom gets inflated because previous packets' ipip0 step
incremented rt->dev (gre0) headroom, and ipip0 incremented because gre0
needed_headroom was increased.
For each subsequent packet, gre/ipip0->needed_headroom grows until
post-expand-head reallocations result in a skb->head/data distance of
more than 64k.
Once that happens, skb->network_header (u16) wraps around when
pskb_expand_head tries to make sure that skb_network_offset() is unchanged
after the headroom expansion/reallocation.
After this skb_network_offset(skb) returns a different (and negative)
result post headroom expansion.
The next trip to neigh layer (or anything else that would __skb_pull the
network header) makes skb->data point to a memory location outside
skb->head area.
v2: Cap the needed_headroom update to an arbitarily chosen upperlimit to
prevent perpetual increase instead of dropping the headroom increment
completely.
Reported-and-tested-by: syzbot+bfde3bef047a81b8fde6@syzkaller.appspotmail.com Closes: https://groups.google.com/g/syzkaller-bugs/c/fL9G6GtWskY/m/VKk_PR5FBAAJ Fixes: 243aad830e8a ("ip_gre: include route header_len in max_headroom calculation") Signed-off-by: Florian Westphal <fw@strlen.de> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/20240220135606.4939-1-fw@strlen.de Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ryosuke Yasuoka [Wed, 21 Feb 2024 07:40:48 +0000 (16:40 +0900)]
netlink: Fix kernel-infoleak-after-free in __skb_datagram_iter
syzbot reported the following uninit-value access issue [1]:
netlink_to_full_skb() creates a new `skb` and puts the `skb->data`
passed as a 1st arg of netlink_to_full_skb() onto new `skb`. The data
size is specified as `len` and passed to skb_put_data(). This `len`
is based on `skb->end` that is not data offset but buffer offset. The
`skb->end` contains data and tailroom. Since the tailroom is not
initialized when the new `skb` created, KMSAN detects uninitialized
memory area when copying the data.
This patch resolved this issue by correct the len from `skb->end` to
`skb->len`, which is the actual data offset.
- ipv6: sr: fix possible use-after-free and null-ptr-deref
- mptcp: fix several data races
- phonet: take correct lock to peek at the RX queue
Misc:
- handful of fixes and reliability improvements for selftests"
* tag 'net-6.8.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (72 commits)
l2tp: pass correct message length to ip6_append_data
net: phy: realtek: Fix rtl8211f_config_init() for RTL8211F(D)(I)-VD-CG PHY
selftests: ioam: refactoring to align with the fix
Fix write to cloned skb in ipv6_hop_ioam()
phonet/pep: fix racy skb_queue_empty() use
phonet: take correct lock to peek at the RX queue
net: sparx5: Add spinlock for frame transmission from CPU
net/sched: flower: Add lock protection when remove filter handle
devlink: fix port dump cmd type
net: stmmac: Fix EST offset for dwmac 5.10
tools: ynl: don't leak mcast_groups on init error
tools: ynl: make sure we always pass yarg to mnl_cb_run
net: mctp: put sock on tag allocation failure
netfilter: nf_tables: use kzalloc for hook allocation
netfilter: nf_tables: register hooks last when adding new chain/flowtable
netfilter: nft_flow_offload: release dst in case direct xmit path is used
netfilter: nft_flow_offload: reset dst in route object after setting up flow
netfilter: nf_tables: set dormant flag on hook register failure
selftests: tls: add test for peeking past a record of a different type
selftests: tls: add test for merging of same-type control messages
...
Linus Torvalds [Thu, 22 Feb 2024 17:23:22 +0000 (09:23 -0800)]
Merge tag 'trace-v6.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull tracing fix from Steven Rostedt:
- While working on the ring buffer I noticed that the counter used for
knowing where the end of the data is on a sub-buffer was not a full
"int" but just 20 bits. It was masked out to 0xfffff.
With the new code that allows the user to change the size of the
sub-buffer, it is theoretically possible to ask for a size bigger
than 2^20. If that happens, unexpected results may occur as there's
no code checking if the counter overflowed the 20 bits of the write
mask. There are other checks to make sure events fit in the
sub-buffer, but if the sub-buffer itself is too big, that is not
checked.
Add a check in the resize of the sub-buffer to make sure that it
never goes beyond the size of the counter that holds how much data is
on it.
* tag 'trace-v6.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
ring-buffer: Do not let subbuf be bigger than write mask
Tom Parkin [Tue, 20 Feb 2024 12:21:56 +0000 (12:21 +0000)]
l2tp: pass correct message length to ip6_append_data
l2tp_ip6_sendmsg needs to avoid accounting for the transport header
twice when splicing more data into an already partially-occupied skbuff.
To manage this, we check whether the skbuff contains data using
skb_queue_empty when deciding how much data to append using
ip6_append_data.
However, the code which performed the calculation was incorrect:
ulen = len + skb_queue_empty(&sk->sk_write_queue) ? transhdrlen : 0;
...due to C operator precedence, this ends up setting ulen to
transhdrlen for messages with a non-zero length, which results in
corrupted packets on the wire.
Add parentheses to correct the calculation in line with the original
intent.
Fixes: 9d4c75800f61 ("ipv4, ipv6: Fix handling of transhdrlen in __ip{,6}_append_data()") Cc: David Howells <dhowells@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Tom Parkin <tparkin@katalix.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/20240220122156.43131-1-tparkin@katalix.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Paolo Abeni [Thu, 22 Feb 2024 09:20:50 +0000 (10:20 +0100)]
Merge tag 'nf-24-02-22' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) If user requests to wake up a table and hook fails, restore the
dormant flag from the error path, from Florian Westphal.
2) Reset dst after transferring it to the flow object, otherwise dst
gets released twice from the error path.
3) Release dst in case the flowtable selects a direct xmit path, eg.
transmission to bridge port. Otherwise, dst is memleaked.
4) Register basechain and flowtable hooks at the end of the command.
Error path releases these datastructure without waiting for the
rcu grace period.
5) Use kzalloc() to initialize struct nft_hook to fix a KMSAN report
on access to hook type, also from Florian Westphal.
netfilter pull request 24-02-22
* tag 'nf-24-02-22' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
netfilter: nf_tables: use kzalloc for hook allocation
netfilter: nf_tables: register hooks last when adding new chain/flowtable
netfilter: nft_flow_offload: release dst in case direct xmit path is used
netfilter: nft_flow_offload: reset dst in route object after setting up flow
netfilter: nf_tables: set dormant flag on hook register failure
====================
Paolo Abeni [Thu, 22 Feb 2024 09:04:46 +0000 (10:04 +0100)]
Merge tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf
Daniel Borkmann says:
====================
pull-request: bpf 2024-02-22
The following pull-request contains BPF updates for your *net* tree.
We've added 11 non-merge commits during the last 24 day(s) which contain
a total of 15 files changed, 217 insertions(+), 17 deletions(-).
The main changes are:
1) Fix a syzkaller-triggered oops when attempting to read the vsyscall
page through bpf_probe_read_kernel and friends, from Hou Tao.
2) Fix a kernel panic due to uninitialized iter position pointer in
bpf_iter_task, from Yafang Shao.
3) Fix a race between bpf_timer_cancel_and_free and bpf_timer_cancel,
from Martin KaFai Lau.
4) Fix a xsk warning in skb_add_rx_frag() (under CONFIG_DEBUG_NET)
due to incorrect truesize accounting, from Sebastian Andrzej Siewior.
5) Fix a NULL pointer dereference in sk_psock_verdict_data_ready,
from Shigeru Yoshida.
6) Fix a resolve_btfids warning when bpf_cpumask symbol cannot be
resolved, from Hari Bathini.
bpf-for-netdev
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
bpf, sockmap: Fix NULL pointer dereference in sk_psock_verdict_data_ready()
selftests/bpf: Add negtive test cases for task iter
bpf: Fix an issue due to uninitialized bpf_iter_task
selftests/bpf: Test racing between bpf_timer_cancel_and_free and bpf_timer_cancel
bpf: Fix racing between bpf_timer_cancel_and_free and bpf_timer_cancel
selftest/bpf: Test the read of vsyscall page under x86-64
x86/mm: Disallow vsyscall page read for copy_from_kernel_nofault()
x86/mm: Move is_vsyscall_vaddr() into asm/vsyscall.h
bpf, scripts: Correct GPL license name
xsk: Add truesize to skb_add_rx_frag().
bpf: Fix warning for bpf_cpumask in verifier
====================
net: phy: realtek: Fix rtl8211f_config_init() for RTL8211F(D)(I)-VD-CG PHY
Commit bb726b753f75 ("net: phy: realtek: add support for
RTL8211F(D)(I)-VD-CG") extended support of the driver from the existing
support for RTL8211F(D)(I)-CG PHY to the newer RTL8211F(D)(I)-VD-CG PHY.
While that commit indicated that the RTL8211F_PHYCR2 register is not
supported by the "VD-CG" PHY model and therefore updated the corresponding
section in rtl8211f_config_init() to be invoked conditionally, the call to
"genphy_soft_reset()" was left as-is, when it should have also been invoked
conditionally. This is because the call to "genphy_soft_reset()" was first
introduced by the commit 0a4355c2b7f8 ("net: phy: realtek: add dt property
to disable CLKOUT clock") since the RTL8211F guide indicates that a PHY
reset should be issued after setting bits in the PHYCR2 register.
As the PHYCR2 register is not applicable to the "VD-CG" PHY model, fix the
rtl8211f_config_init() function by invoking "genphy_soft_reset()"
conditionally based on the presence of the "PHYCR2" register.
Fixes: bb726b753f75 ("net: phy: realtek: add support for RTL8211F(D)(I)-VD-CG") Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/20240220070007.968762-1-s-vadapalli@ti.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Justin Iurman [Mon, 19 Feb 2024 13:52:55 +0000 (14:52 +0100)]
selftests: ioam: refactoring to align with the fix
ioam6_parser uses a packet socket. After the fix to prevent writing to
cloned skb's, the receiver does not see its IOAM data anymore, which
makes input/forward ioam-selftests to fail. As a workaround,
ioam6_parser now uses an IPv6 raw socket and leverages ancillary data to
get hop-by-hop options. As a consequence, the hook is "after" the IOAM
data insertion by the receiver and all tests are working again.
Signed-off-by: Justin Iurman <justin.iurman@uliege.be> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Justin Iurman [Mon, 19 Feb 2024 13:52:54 +0000 (14:52 +0100)]
Fix write to cloned skb in ipv6_hop_ioam()
ioam6_fill_trace_data() writes inside the skb payload without ensuring
it's writeable (e.g., not cloned). This function is called both from the
input and output path. The output path (ioam6_iptunnel) already does the
check. This commit provides a fix for the input path, inside
ipv6_hop_ioam(). It also updates ip6_parse_tlv() to refresh the network
header pointer ("nh") when returning from ipv6_hop_ioam().
Fixes: 9ee11f0fff20 ("ipv6: ioam: Data plane support for Pre-allocated Trace") Reported-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Justin Iurman <justin.iurman@uliege.be> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The receive queues are protected by their respective spin-lock, not
the socket lock. This could lead to skb_peek() unexpectedly
returning NULL or a pointer to an already dequeued socket buffer.
Horatiu Vultur [Mon, 19 Feb 2024 08:00:43 +0000 (09:00 +0100)]
net: sparx5: Add spinlock for frame transmission from CPU
Both registers used when doing manual injection or fdma injection are
shared between all the net devices of the switch. It was noticed that
when having two process which each of them trying to inject frames on
different ethernet ports, that the HW started to behave strange, by
sending out more frames then expected. When doing fdma injection it is
required to set the frame in the DCB and then make sure that the next
pointer of the last DCB is invalid. But because there is no locks for
this, then easily this pointer between the DCB can be broken and then it
would create a loop of DCBs. And that means that the HW will
continuously transmit these frames in a loop. Until the SW will break
this loop.
Therefore to fix this issue, add a spin lock for when accessing the
registers for manual or fdma injection.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Daniel Machon <daniel.machon@microchip.com> Fixes: f3cad2611a77 ("net: sparx5: add hostmode with phylink support") Link: https://lore.kernel.org/r/20240219080043.1561014-1-horatiu.vultur@microchip.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jiri Pirko [Tue, 20 Feb 2024 07:52:45 +0000 (08:52 +0100)]
devlink: fix port dump cmd type
Unlike other commands, due to a c&p error, port dump fills-up cmd with
wrong value, different from port-get request cmd, port-get doit reply
and port notification.
Fix it by filling cmd with value DEVLINK_CMD_PORT_NEW.
Skimmed through devlink userspace implementations, none of them cares
about this cmd value. Only ynl, for which, this is actually a fix, as it
expects doit and dumpit ops rsp_value to be the same.
Omit the fixes tag, even thought this is fix, better to target this for
next release.
Fixes: bfcd3a466172 ("Introduce devlink infrastructure") Signed-off-by: Jiri Pirko <jiri@nvidia.com> Reviewed-by: Simon Horman <horms@kernel.org> Reviewed-by: Jakub Kicinski <kuba@kernel.org> Link: https://lore.kernel.org/r/20240220075245.75416-1-jiri@resnulli.us Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Tue, 20 Feb 2024 16:11:12 +0000 (08:11 -0800)]
tools: ynl: don't leak mcast_groups on init error
Make sure to free the already-parsed mcast_groups if
we don't get an ack from the kernel when reading family info.
This is part of the ynl_sock_create() error path, so we won't
get a call to ynl_sock_destroy() to free them later.
Jakub Kicinski [Tue, 20 Feb 2024 16:11:11 +0000 (08:11 -0800)]
tools: ynl: make sure we always pass yarg to mnl_cb_run
There is one common error handler in ynl - ynl_cb_error().
It expects priv to be a pointer to struct ynl_parse_arg AKA yarg.
To avoid potential crashes if we encounter a stray NLMSG_ERROR
always pass yarg as priv (or a struct which has it as the first
member).
ynl_cb_null() has a similar problem directly - it expects yarg
but priv passed by the caller is ys.
Jeremy Kerr [Thu, 15 Feb 2024 07:53:08 +0000 (15:53 +0800)]
net: mctp: put sock on tag allocation failure
We may hold an extra reference on a socket if a tag allocation fails: we
optimistically allocate the sk_key, and take a ref there, but do not
drop if we end up not using the allocated key.
Ensure we're dropping the sock on this failure by doing a proper unref
rather than directly kfree()ing.
netfilter: nf_tables: register hooks last when adding new chain/flowtable
Register hooks last when adding chain/flowtable to ensure that packets do
not walk over datastructure that is being released in the error path
without waiting for the rcu grace period.
Fixes: 91c7b38dc9f0 ("netfilter: nf_tables: use new transaction infrastructure to handle chain") Fixes: 3b49e2e94e6e ("netfilter: nf_tables: add flow table netlink frontend") Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
netfilter: nft_flow_offload: reset dst in route object after setting up flow
dst is transferred to the flow object, route object does not own it
anymore. Reset dst in route object, otherwise if flow_offload_add()
fails, error path releases dst twice, leading to a refcount underflow.
====================
tls: fixes for record type handling with PEEK
There are multiple bugs in tls_sw_recvmsg's handling of record types
when MSG_PEEK flag is used, which can lead to incorrectly merging two
records:
- consecutive non-DATA records shouldn't be merged, even if they're
the same type (partly handled by the test at the end of the main
loop)
- records of the same type (even DATA) shouldn't be merged if one
record of a different type comes in between
====================
Sabrina Dubroca [Thu, 15 Feb 2024 16:17:33 +0000 (17:17 +0100)]
selftests: tls: add test for peeking past a record of a different type
If we queue 3 records:
- record 1, type DATA
- record 2, some other type
- record 3, type DATA
the current code can look past the 2nd record and merge the 2 data
records.
Sabrina Dubroca [Thu, 15 Feb 2024 16:17:31 +0000 (17:17 +0100)]
tls: don't skip over different type records from the rx_list
If we queue 3 records:
- record 1, type DATA
- record 2, some other type
- record 3, type DATA
and do a recv(PEEK), the rx_list will contain the first two records.
The next large recv will walk through the rx_list and copy data from
record 1, then stop because record 2 is a different type. Since we
haven't filled up our buffer, we will process the next available
record. It's also DATA, so we can merge it with the current read.
We shouldn't do that, since there was a record in between that we
ignored.
Add a flag to let process_rx_list inform tls_sw_recvmsg that it had
more data available.
Sabrina Dubroca [Thu, 15 Feb 2024 16:17:30 +0000 (17:17 +0100)]
tls: stop recv() if initial process_rx_list gave us non-DATA
If we have a non-DATA record on the rx_list and another record of the
same type still on the queue, we will end up merging them:
- process_rx_list copies the non-DATA record
- we start the loop and process the first available record since it's
of the same type
- we break out of the loop since the record was not DATA
Just check the record type and jump to the end in case process_rx_list
did some work.
Sabrina Dubroca [Thu, 15 Feb 2024 16:17:29 +0000 (17:17 +0100)]
tls: break out of main loop when PEEK gets a non-data record
PEEK needs to leave decrypted records on the rx_list so that we can
receive them later on, so it jumps back into the async code that
queues the skb. Unfortunately that makes us skip the
TLS_RECORD_TYPE_DATA check at the bottom of the main loop, so if two
records of the same (non-DATA) type are queued, we end up merging
them.
Add the same record type check, and make it unlikely to not penalize
the async fastpath. Async decrypt only applies to data record, so this
check is only needed for PEEK.
Jeff Johnson [Sat, 17 Feb 2024 20:47:02 +0000 (12:47 -0800)]
MAINTAINERS: wifi: Add N: ath1*k entries to match .yaml files
In [1] it was observed that the ath12k maintainers were not added to
the review of a new ath12k YAML file. Bartosz suggested "adding an N:
ath12k entry to MAINTAINERS" to prevent this in the future. In the
process it was noticed that one of the ath11k YAML files was also not
explicitly referenced, so add N: entries to ath10k, ath11k, and
ath12k, and remove the explicit F: entries.
Linus Torvalds [Wed, 21 Feb 2024 17:13:27 +0000 (09:13 -0800)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"Two fixes for ARM ITS emulation. Unmapped interrupts were used instead
of ignored, causing NULL pointer dereferences"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: arm64: vgic-its: Test for valid IRQ in MOVALL handler
KVM: arm64: vgic-its: Test for valid IRQ in its_sync_lpi_pending_table()
Linus Torvalds [Wed, 21 Feb 2024 16:45:07 +0000 (08:45 -0800)]
Merge tag 'for-6.8-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
- Fix a deadlock in fiemap.
There was a big lock around the whole operation that can interfere
with a page fault and mkwrite.
Reducing the lock scope can also speed up fiemap
- Fix range condition for extent defragmentation which could lead to
worse layout in some cases
* tag 'for-6.8-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: fix deadlock with fiemap and extent locking
btrfs: defrag: avoid unnecessary defrag caused by incorrect extent size
If sk_psock_verdict_data_ready() and sk_psock_stop_verdict() are called
concurrently, psock->saved_data_ready can be NULL, causing the above issue.
This patch fixes this issue by calling the appropriate data ready function
using the sk_psock_data_ready() helper and protecting it from concurrency
with sk->sk_callback_lock.
Fixes: 6df7f764cd3c ("bpf, sockmap: Wake up polling after data copy") Reported-by: syzbot+fd7b34375c1c8ce29c93@syzkaller.appspotmail.com Signed-off-by: Shigeru Yoshida <syoshida@redhat.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Tested-by: syzbot+fd7b34375c1c8ce29c93@syzkaller.appspotmail.com Acked-by: John Fastabend <john.fastabend@gmail.com> Closes: https://syzkaller.appspot.com/bug?extid=fd7b34375c1c8ce29c93 [1] Link: https://lore.kernel.org/bpf/20240218150933.6004-1-syoshida@redhat.com
ring-buffer: Do not let subbuf be bigger than write mask
The data on the subbuffer is measured by a write variable that also
contains status flags. The counter is just 20 bits in length. If the
subbuffer is bigger than then counter, it will fail.
Make sure that the subbuffer can not be set to greater than the counter
that keeps track of the data on the subbuffer.
Link: https://lore.kernel.org/linux-trace-kernel/20240220095112.77e9cb81@gandalf.local.home Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Fixes: 2808e31ec12e5 ("ring-buffer: Add interface for configuring trace sub buffer size") Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
wifi: iwlwifi: mvm: fix the TXF mapping for BZ devices
Those devices' fifos are numbered differently.
Because of that, we were looking at the size of the VO fifo size to
determine the size of the A-MSDU which led to a lower throughput.
Note that for those devices the only user of the AC -> fifo mapping is
the size limitation of A-MSDU.
Benjamin Berg [Sun, 18 Feb 2024 17:51:47 +0000 (19:51 +0200)]
wifi: iwlwifi: mvm: ensure offloading TID queue exists
The resume code path assumes that the TX queue for the offloading TID
has been configured. At resume time it then tries to sync the write
pointer as it may have been updated by the firmware.
In the unusual event that no packets have been send on TID 0, the queue
will not have been allocated and this causes a crash. Fix this by
ensuring the queue exist at suspend time.
Simon Horman [Mon, 19 Feb 2024 17:55:31 +0000 (17:55 +0000)]
MAINTAINERS: Add framer headers to NETWORKING [GENERAL]
The cited commit [1] added framer support under drivers/net/wan,
which is covered by NETWORKING [GENERAL]. And it is implied
that framer-provider.h and framer.h, which were also added
buy the same patch, are also maintained as part of NETWORKING [GENERAL].
Make this explicit by adding these files to the corresponding
section in MAINTAINERS.
Signed-off-by: Simon Horman <horms@kernel.org> Reviewed-by: Herve Codina <herve.codina@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
af_unix: Drop oob_skb ref before purging queue in GC.
syzbot reported another task hung in __unix_gc(). [0]
The current while loop assumes that all of the left candidates
have oob_skb and calling kfree_skb(oob_skb) releases the remaining
candidates.
However, I missed a case that oob_skb has self-referencing fd and
another fd and the latter sk is placed before the former in the
candidate list. Then, the while loop never proceeds, resulting
the task hung.
__unix_gc() has the same loop just before purging the collected skb,
so we can call kfree_skb(oob_skb) there and let __skb_queue_purge()
release all inflight sockets.
Reported-and-tested-by: syzbot+ecab4d36f920c3574bf9@syzkaller.appspotmail.com Closes: https://syzkaller.appspot.com/bug?extid=ecab4d36f920c3574bf9 Fixes: 25236c91b5ab ("af_unix: Fix task hung while purging oob_skb in GC.") Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
In newer hardware, IPA supports more than 32 endpoints. Some
registers--such as IPA interrupt registers--represent endpoints
as bits in a 4-byte register, and such registers are repeated as
needed to represent endpoints beyond the first 32.
In ipa_interrupt_suspend_clear_all(), we clear all pending IPA
suspend interrupts by reading all status register(s) and writing
corresponding registers to clear interrupt conditions.
Unfortunately the number of registers to read/write is calculated
incorrectly, and as a result we access *many* more registers than
intended. This bug occurs only when the IPA hardware signals a
SUSPEND interrupt, which happens when a packet is received for an
endpoint (or its underlying GSI channel) that is suspended. This
situation is difficult to reproduce, but possible.
Fix this by correctly computing the number of interrupt registers to
read and write. This is the only place in the code where registers
that map endpoints or channels this way perform this calculation.
Fixes: f298ba785e2d ("net: ipa: add a parameter to suspend registers") Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 19 Feb 2024 14:12:20 +0000 (14:12 +0000)]
net: implement lockless setsockopt(SO_PEEK_OFF)
syzbot reported a lockdep violation [1] involving af_unix
support of SO_PEEK_OFF.
Since SO_PEEK_OFF is inherently not thread safe (it uses a per-socket
sk_peek_off field), there is really no point to enforce a pointless
thread safety in the kernel.
After this patch :
- setsockopt(SO_PEEK_OFF) no longer acquires the socket lock.
- skb_consume_udp() no longer has to acquire the socket lock.
- af_unix no longer needs a special version of sk_set_peek_off(),
because it does not lock u->iolock anymore.
As a followup, we could replace prot->set_peek_off to be a boolean
and avoid an indirect call, since we always use sk_set_peek_off().
Fixes: 859051dd165e ("bpf: Implement cgroup sockaddr hooks for unix sockets") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Willem de Bruijn <willemdebruijn.kernel@gmail.com> Cc: Daan De Meyer <daan.j.demeyer@gmail.com> Cc: Kuniyuki Iwashima <kuniyu@amazon.com> Cc: Martin KaFai Lau <martin.lau@kernel.org> Cc: David Ahern <dsahern@kernel.org> Reviewed-by: Willem de Bruijn <willemb@google.com> Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
AF reserves MCAM entries for each PF, VF present in the
system and populates the entry with DMAC and action with
default RSS so that basic packet I/O works. Since PF/VF is
not aware of the RSS action installed by AF, AF only fixup
the actions of the rules installed by PF/VF with corresponding
default RSS action. This worked well for rules installed by
PF/VF for features like RX VLAN offload and DMAC filters but
rules involving action like drop/forward to queue are also
getting modified by AF. Hence fix it by setting the default
RSS action only if requested by PF/VF.
Fixes: 967db3529eca ("octeontx2-af: add support for multicast/promisc packet replication feature") Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Oliver Upton [Wed, 21 Feb 2024 09:27:32 +0000 (09:27 +0000)]
KVM: arm64: vgic-its: Test for valid IRQ in MOVALL handler
It is possible that an LPI mapped in a different ITS gets unmapped while
handling the MOVALL command. If that is the case, there is no state that
can be migrated to the destination. Silently ignore it and continue
migrating other LPIs.
Oliver Upton [Wed, 21 Feb 2024 09:27:31 +0000 (09:27 +0000)]
KVM: arm64: vgic-its: Test for valid IRQ in its_sync_lpi_pending_table()
vgic_get_irq() may not return a valid descriptor if there is no ITS that
holds a valid translation for the specified INTID. If that is the case,
it is safe to silently ignore it and continue processing the LPI pending
table.
Linus Torvalds [Wed, 21 Feb 2024 01:00:26 +0000 (17:00 -0800)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma fixes from Jason Gunthorpe:
"Mostly irdma and bnxt_re fixes:
- Missing error unwind in hf1
- For bnxt - fix fenching behavior to work on new chips, fail
unsupported SRQ resize back to userspace, propogate SRQ FW failure
back to userspace.
- Correctly fail unsupported SRQ resize back to userspace in bnxt
- Adjust a memcpy in mlx5 to not overflow a struct field.
- Prevent userspace from triggering mlx5 fw syndrome logging from
sysfs
- Use the correct access mode for MLX5_IB_METHOD_DEVX_OBJ_MODIFY to
avoid a userspace failure on modify
- For irdma - Don't UAF a concurrent tasklet during destroy, prevent
userspace from issuing invalid QP attrs, fix a possible CQ
overflow, capture a missing HW async error event
- sendmsg() triggerable memory access crash in hfi1
- Fix the srpt_service_guid parameter to not crash due to missing
function pointer
- Don't leak objects in error unwind in qedr
- Don't weirdly cast function pointers in srpt"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/srpt: fix function pointer cast warnings
RDMA/qedr: Fix qedr_create_user_qp error flow
RDMA/srpt: Support specifying the srpt_service_guid parameter
IB/hfi1: Fix sdma.h tx->num_descs off-by-one error
RDMA/irdma: Add AE for too many RNRS
RDMA/irdma: Set the CQ read threshold for GEN 1
RDMA/irdma: Validate max_send_wr and max_recv_wr
RDMA/irdma: Fix KASAN issue with tasklet
RDMA/mlx5: Relax DEVX access upon modify commands
IB/mlx5: Don't expose debugfs entries for RRoCE general parameters if not supported
RDMA/mlx5: Fix fortify source warning while accessing Eth segment
RDMA/bnxt_re: Add a missing check in bnxt_qplib_query_srq
RDMA/bnxt_re: Return error for SRQ resize
RDMA/bnxt_re: Fix unconditional fence for newer adapters
RDMA/bnxt_re: Remove a redundant check inside bnxt_re_vf_res_config
RDMA/bnxt_re: Avoid creating fence MR for newer adapters
IB/hfi1: Fix a memleak in init_credit_return
Amritha Nambiar [Tue, 13 Feb 2024 19:48:50 +0000 (11:48 -0800)]
ice: Fix ASSERT_RTNL() warning during certain scenarios
Commit 91fdbce7e8d6 ("ice: Add support in the driver for associating
queue with napi") invoked the netif_queue_set_napi() call. This
kernel function requires to be called with rtnl_lock taken,
otherwise ASSERT_RTNL() warning will be triggered. ice_vsi_rebuild()
initiating this call is under rtnl_lock when the rebuild is in
response to configuration changes from external interfaces (such as
tc, ethtool etc. which holds the lock). But, the VSI rebuild
generated from service tasks and resets (PFR/CORER/GLOBR) is not
under rtnl lock protection. Handle these cases as well to hold lock
before the kernel call (by setting the 'locked' boolean to false).
netif_queue_set_napi() is also used to clear previously set napi
in the q_vector unroll flow. Handle this for locked/lockless execution
paths.
Fixes: 91fdbce7e8d6 ("ice: Add support in the driver for associating queue with napi") Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com> Reviewed-by: Sridhar Samudrala <sridhar.samudrala@intel.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
and the uses of 'u64' are all entirely pointless. Yes, the arguments to
drm_buddy_init() and drm_buddy_alloc_blocks() are in fact of type 'u64',
but none of the values here are remotely relevant, and the compiler will
happily just do the type expansion.
Of course, in a perfect world the compiler would also have just noticed
that all the values in question are tiny, and range analysis would have
shown that doing a 64-bit divide is pointless, but that is admittedly
expecting a fair amount of the compiler.
IOW, we shouldn't write code that the compiler then has to notice is
unnecessarily complicated just to avoid extra work. We do have fairly
high expectations of compilers, but kernel code should be reasonable to
begin with.
It turns out that there are also other issues with this code: the KUnit
assertion messages have incorrect types in the format strings, but
that's a widely spread issue caused by the KUnit infrastructure not
having enabled format string verification. We'll get that sorted out
separately.
Reported-by: Guenter Roeck <linux@roeck-us.net> Fixes: a64056bb5a32 ("drm/tests/drm_buddy: add alloc_contiguous test") Link: https://lore.kernel.org/all/538327ff-8d34-41d5-a9ae-1a334744f5ae@roeck-us.net/ Cc: Matthew Auld <matthew.auld@intel.com> Cc: Arunpravin Paneer Selvam <Arunpravin.PaneerSelvam@amd.com> Cc: Christian König <christian.koenig@amd.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
projects / mirror_ubuntu-kernels.git / log