John Fastabend [Sun, 18 Mar 2018 19:58:07 +0000 (12:58 -0700)]
bpf: sockmap add SK_DROP tests
Add tests for SK_DROP.
Signed-off-by: John Fastabend <john.fastabend@gmail.com> Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
John Fastabend [Sun, 18 Mar 2018 19:58:02 +0000 (12:58 -0700)]
bpf: sockmap sample support for bpf_msg_cork_bytes()
Add sample application support for the bpf_msg_cork_bytes helper. This
lets the user specify how many bytes each verdict should apply to.
Similar to apply_bytes() tests these can be run as a stand-alone test
when used without other options or inline with other tests by using
the txmsg_cork option along with any of the basic tests txmsg,
txmsg_redir, txmsg_drop.
Signed-off-by: John Fastabend <john.fastabend@gmail.com> Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
John Fastabend [Sun, 18 Mar 2018 19:57:56 +0000 (12:57 -0700)]
bpf: sockmap, add sample option to test apply_bytes helper
This adds an option to test the apply_bytes helper. This option lets
the user specify an int on the command line specifying how much data
each verdict should apply to.
When this is set a map entry is set with the bytes input by the user
and then the specified program --txmsg or --txmsg_redir will use the
value and set the applied data. If no other option is set then a
default --txmsg_apply program is run. This program will drop pkts
if an error is detected on the bytes map lookup. Useful to verify
the map lookup and apply helper are working and causing a hard
error if it is not.
Signed-off-by: John Fastabend <john.fastabend@gmail.com> Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
John Fastabend [Sun, 18 Mar 2018 19:57:51 +0000 (12:57 -0700)]
bpf: sockmap sample, add data verification option
To verify data is not being dropped or corrupted this adds an option
to verify test-patterns on recv.
Signed-off-by: John Fastabend <john.fastabend@gmail.com> Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
John Fastabend [Sun, 18 Mar 2018 19:57:46 +0000 (12:57 -0700)]
bpf: sockmap sample, add sendfile test
To exercise TX ULP sendpage implementation we need a test that does
a sendfile. Add sendfile test option here.
Signed-off-by: John Fastabend <john.fastabend@gmail.com> Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
John Fastabend [Sun, 18 Mar 2018 19:57:41 +0000 (12:57 -0700)]
bpf: sockmap sample, add option to attach SK_MSG program
Add sockmap option to use SK_MSG program types.
Signed-off-by: John Fastabend <john.fastabend@gmail.com> Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
John Fastabend [Sun, 18 Mar 2018 19:57:36 +0000 (12:57 -0700)]
bpf: add verifier tests for BPF_PROG_TYPE_SK_MSG
Test read and writes for BPF_PROG_TYPE_SK_MSG.
Signed-off-by: John Fastabend <john.fastabend@gmail.com> Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
John Fastabend [Sun, 18 Mar 2018 19:57:31 +0000 (12:57 -0700)]
bpf: add map tests for BPF_PROG_TYPE_SK_MSG
Add map tests to attach BPF_PROG_TYPE_SK_MSG types to a sockmap.
Signed-off-by: John Fastabend <john.fastabend@gmail.com> Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
John Fastabend [Sun, 18 Mar 2018 19:57:25 +0000 (12:57 -0700)]
bpf: sk_msg program helper bpf_sk_msg_pull_data
Currently, if a bpf sk msg program is run the program
can only parse data that the (start,end) pointers already
consumed. For sendmsg hooks this is likely the first
scatterlist element. For sendpage this will be the range
(0,0) because the data is shared with userspace and by
default we want to avoid allowing userspace to modify
data while (or after) BPF verdict is being decided.
To support pulling in additional bytes for parsing use
a new helper bpf_sk_msg_pull(start, end, flags) which
works similar to cls tc logic. This helper will attempt
to point the data start pointer at 'start' bytes offest
into msg and data end pointer at 'end' bytes offset into
message.
After basic sanity checks to ensure 'start' <= 'end' and
'end' <= msg_length there are a few cases we need to
handle.
First the sendmsg hook has already copied the data from
userspace and has exclusive access to it. Therefor, it
is not necessesary to copy the data. However, it may
be required. After finding the scatterlist element with
'start' offset byte in it there are two cases. One the
range (start,end) is entirely contained in the sg element
and is already linear. All that is needed is to update the
data pointers, no allocate/copy is needed. The other case
is (start, end) crosses sg element boundaries. In this
case we allocate a block of size 'end - start' and copy
the data to linearize it.
Next sendpage hook has not copied any data in initial
state so that data pointers are (0,0). In this case we
handle it similar to the above sendmsg case except the
allocation/copy must always happen. Then when sending
the data we have possibly three memory regions that
need to be sent, (0, start - 1), (start, end), and
(end + 1, msg_length). This is required to ensure any
writes by the BPF program are correctly transmitted.
Lastly this operation will invalidate any previous
data checks so BPF programs will have to revalidate
pointers after making this BPF call.
Signed-off-by: John Fastabend <john.fastabend@gmail.com> Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
John Fastabend [Sun, 18 Mar 2018 19:57:20 +0000 (12:57 -0700)]
bpf: sockmap, add msg_cork_bytes() helper
In the case where we need a specific number of bytes before a
verdict can be assigned, even if the data spans multiple sendmsg
or sendfile calls. The BPF program may use msg_cork_bytes().
The extreme case is a user can call sendmsg repeatedly with
1-byte msg segments. Obviously, this is bad for performance but
is still valid. If the BPF program needs N bytes to validate
a header it can use msg_cork_bytes to specify N bytes and the
BPF program will not be called again until N bytes have been
accumulated. The infrastructure will attempt to coalesce data
if possible so in many cases (most my use cases at least) the
data will be in a single scatterlist element with data pointers
pointing to start/end of the element. However, this is dependent
on available memory so is not guaranteed. So BPF programs must
validate data pointer ranges, but this is the case anyways to
convince the verifier the accesses are valid.
Signed-off-by: John Fastabend <john.fastabend@gmail.com> Acked-by: David S. Miller <davem@davemloft.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
John Fastabend [Sun, 18 Mar 2018 19:57:15 +0000 (12:57 -0700)]
bpf: sockmap, add bpf_msg_apply_bytes() helper
A single sendmsg or sendfile system call can contain multiple logical
messages that a BPF program may want to read and apply a verdict. But,
without an apply_bytes helper any verdict on the data applies to all
bytes in the sendmsg/sendfile. Alternatively, a BPF program may only
care to read the first N bytes of a msg. If the payload is large say
MB or even GB setting up and calling the BPF program repeatedly for
all bytes, even though the verdict is already known, creates
unnecessary overhead.
To allow BPF programs to control how many bytes a given verdict
applies to we implement a bpf_msg_apply_bytes() helper. When called
from within a BPF program this sets a counter, internal to the
BPF infrastructure, that applies the last verdict to the next N
bytes. If the N is smaller than the current data being processed
from a sendmsg/sendfile call, the first N bytes will be sent and
the BPF program will be re-run with start_data pointing to the N+1
byte. If N is larger than the current data being processed the
BPF verdict will be applied to multiple sendmsg/sendfile calls
until N bytes are consumed.
Note1 if a socket closes with apply_bytes counter non-zero this
is not a problem because data is not being buffered for N bytes
and is sent as its received.
Signed-off-by: John Fastabend <john.fastabend@gmail.com> Acked-by: David S. Miller <davem@davemloft.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
John Fastabend [Sun, 18 Mar 2018 19:57:10 +0000 (12:57 -0700)]
bpf: create tcp_bpf_ulp allowing BPF to monitor socket TX/RX data
This implements a BPF ULP layer to allow policy enforcement and
monitoring at the socket layer. In order to support this a new
program type BPF_PROG_TYPE_SK_MSG is used to run the policy at
the sendmsg/sendpage hook. To attach the policy to sockets a
sockmap is used with a new program attach type BPF_SK_MSG_VERDICT.
Similar to previous sockmap usages when a sock is added to a
sockmap, via a map update, if the map contains a BPF_SK_MSG_VERDICT
program type attached then the BPF ULP layer is created on the
socket and the attached BPF_PROG_TYPE_SK_MSG program is run for
every msg in sendmsg case and page/offset in sendpage case.
BPF_PROG_TYPE_SK_MSG Semantics/API:
BPF_PROG_TYPE_SK_MSG supports only two return codes SK_PASS and
SK_DROP. Returning SK_DROP free's the copied data in the sendmsg
case and in the sendpage case leaves the data untouched. Both cases
return -EACESS to the user. Returning SK_PASS will allow the msg to
be sent.
In the sendmsg case data is copied into kernel space buffers before
running the BPF program. The kernel space buffers are stored in a
scatterlist object where each element is a kernel memory buffer.
Some effort is made to coalesce data from the sendmsg call here.
For example a sendmsg call with many one byte iov entries will
likely be pushed into a single entry. The BPF program is run with
data pointers (start/end) pointing to the first sg element.
In the sendpage case data is not copied. We opt not to copy the
data by default here, because the BPF infrastructure does not
know what bytes will be needed nor when they will be needed. So
copying all bytes may be wasteful. Because of this the initial
start/end data pointers are (0,0). Meaning no data can be read or
written. This avoids reading data that may be modified by the
user. A new helper is added later in this series if reading and
writing the data is needed. The helper call will do a copy by
default so that the page is exclusively owned by the BPF call.
The verdict from the BPF_PROG_TYPE_SK_MSG applies to the entire msg
in the sendmsg() case and the entire page/offset in the sendpage case.
This avoids ambiguity on how to handle mixed return codes in the
sendmsg case. Again a helper is added later in the series if
a verdict needs to apply to multiple system calls and/or only
a subpart of the currently being processed message.
The helper msg_redirect_map() can be used to select the socket to
send the data on. This is used similar to existing redirect use
cases. This allows policy to redirect msgs.
Pseudo code simple example:
The basic logic to attach a program to a socket is as follows,
// load the programs
bpf_prog_load(SOCKMAP_TCP_MSG_PROG, BPF_PROG_TYPE_SK_MSG,
&obj, &msg_prog);
// lookup the sockmap
bpf_map_msg = bpf_object__find_map_by_name(obj, "my_sock_map");
// get fd for sockmap
map_fd_msg = bpf_map__fd(bpf_map_msg);
// attach program to sockmap
bpf_prog_attach(msg_prog, map_fd_msg, BPF_SK_MSG_VERDICT, 0);
Adding sockets to the map is done in the normal way,
// Add a socket 'fd' to sockmap at location 'i'
bpf_map_update_elem(map_fd_msg, &i, fd, BPF_ANY);
After the above any socket attached to "my_sock_map", in this case
'fd', will run the BPF msg verdict program (msg_prog) on every
sendmsg and sendpage system call.
For a complete example see BPF selftests or sockmap samples.
Implementation notes:
It seemed the simplest, to me at least, to use a refcnt to ensure
psock is not lost across the sendmsg copy into the sg, the bpf program
running on the data in sg_data, and the final pass to the TCP stack.
Some performance testing may show a better method to do this and avoid
the refcnt cost, but for now use the simpler method.
Another item that will come after basic support is in place is
supporting MSG_MORE flag. At the moment we call sendpages even if
the MSG_MORE flag is set. An enhancement would be to collect the
pages into a larger scatterlist and pass down the stack. Notice that
bpf_tcp_sendmsg() could support this with some additional state saved
across sendmsg calls. I built the code to support this without having
to do refactoring work. Other features TBD include ZEROCOPY and the
TCP_RECV_QUEUE/TCP_NO_QUEUE support. This will follow initial series
shortly.
Future work could improve size limits on the scatterlist rings used
here. Currently, we use MAX_SKB_FRAGS simply because this was being
used already in the TLS case. Future work could extend the kernel sk
APIs to tune this depending on workload. This is a trade-off
between memory usage and throughput performance.
Signed-off-by: John Fastabend <john.fastabend@gmail.com> Acked-by: David S. Miller <davem@davemloft.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
John Fastabend [Sun, 18 Mar 2018 19:57:05 +0000 (12:57 -0700)]
net: generalize sk_alloc_sg to work with scatterlist rings
The current implementation of sk_alloc_sg expects scatterlist to always
start at entry 0 and complete at entry MAX_SKB_FRAGS.
Future patches will want to support starting at arbitrary offset into
scatterlist so add an additional sg_start parameters and then default
to the current values in TLS code paths.
Signed-off-by: John Fastabend <john.fastabend@gmail.com> Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
John Fastabend [Sun, 18 Mar 2018 19:57:00 +0000 (12:57 -0700)]
net: do_tcp_sendpages flag to avoid SKBTX_SHARED_FRAG
When calling do_tcp_sendpages() from in kernel and we know the data
has no references from user side we can omit SKBTX_SHARED_FRAG flag.
This patch adds an internal flag, NO_SKBTX_SHARED_FRAG that can be used
to omit setting SKBTX_SHARED_FRAG.
The flag is not exposed to userspace because the sendpage call from
the splice logic masks out all bits except MSG_MORE.
Signed-off-by: John Fastabend <john.fastabend@gmail.com> Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
John Fastabend [Sun, 18 Mar 2018 19:56:54 +0000 (12:56 -0700)]
sockmap: convert refcnt to an atomic refcnt
The sockmap refcnt up until now has been wrapped in the
sk_callback_lock(). So its not actually needed any locking of its
own. The counter itself tracks the lifetime of the psock object.
Sockets in a sockmap have a lifetime that is independent of the
map they are part of. This is possible because a single socket may
be in multiple maps. When this happens we can only release the
psock data associated with the socket when the refcnt reaches
zero. There are three possible delete sock reference decrement
paths first through the normal sockmap process, the user deletes
the socket from the map. Second the map is removed and all sockets
in the map are removed, delete path is similar to case 1. The third
case is an asyncronous socket event such as a closing the socket. The
last case handles removing sockets that are no longer available.
For completeness, although inc does not pose any problems in this
patch series, the inc case only happens when a psock is added to a
map.
Next we plan to add another socket prog type to handle policy and
monitoring on the TX path. When we do this however we will need to
keep a reference count open across the sendmsg/sendpage call and
holding the sk_callback_lock() here (on every send) seems less than
ideal, also it may sleep in cases where we hit memory pressure.
Instead of dealing with these issues in some clever way simply make
the reference counting a refcnt_t type and do proper atomic ops.
Signed-off-by: John Fastabend <john.fastabend@gmail.com> Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
John Fastabend [Sun, 18 Mar 2018 19:56:49 +0000 (12:56 -0700)]
sock: make static tls function alloc_sg generic sock helper
The TLS ULP module builds scatterlists from a sock using
page_frag_refill(). This is going to be useful for other ULPs
so move it into sock file for more general use.
In the process remove useless goto at end of while loop.
Signed-off-by: John Fastabend <john.fastabend@gmail.com> Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Daniel Borkmann [Fri, 16 Mar 2018 08:25:00 +0000 (09:25 +0100)]
Merge branch 'bpf-tools-build-improvements'
Jakub Kicinski says:
====================
As promised this series addresses nits and minor issues in tools/bpf
build infra. One GCC-7 warning which is nice to get rid of. Dependencies
when built with OUTPUT are fixed. make clean will now remove the
FEATURE-DUMP.* files. PHONY target is also updated to match reality.
====================
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Jakub Kicinski [Fri, 16 Mar 2018 06:26:15 +0000 (23:26 -0700)]
tools: bpftool: fix potential format truncation
GCC 7 complains:
xlated_dumper.c: In function ‘print_call’:
xlated_dumper.c:179:10: warning: ‘%s’ directive output may be truncated writing up to 255 bytes into a region of size between 249 and 253 [-Wformat-truncation=]
"%+d#%s", insn->off, sym->name);
Add a bit more space to the buffer so it can handle the entire
string and integer without truncation.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Jakub Kicinski [Fri, 16 Mar 2018 06:26:14 +0000 (23:26 -0700)]
tools: bpftool: fix dependency file path
Auto-generated dependency files are in the OUTPUT directory,
we need to include them from there. This fixes object files
not being rebuilt after header changes.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Daniel Borkmann [Thu, 15 Mar 2018 00:14:01 +0000 (01:14 +0100)]
Merge branch 'bpf-stackmap-build-id'
Song Liu says:
====================
This work follows up discussion at Plumbers'17 on improving addr->sym
resolution of user stack traces. The following links have more information
of the discussion:
http://www.linuxplumbersconf.org/2017/ocw/proposals/4764
https://lwn.net/Articles/734453/ Section "Stack traces and kprobes"
Currently, bpf stackmap store address for each entry in the call trace.
To map these addresses to user space files, it is necessary to maintain
the mapping from these virtual address to symbols in the binary. Usually,
the user space profiler (such as perf) has to scan /proc/pid/maps at the
beginning of profiling, and monitor mmap2() calls afterwards. Given the
cost of maintaining the address map, this solution is not practical for
system wide profiling that is always on.
This patch tries to address this with a variation to stackmap. Instead
of storing addresses, the variation stores ELF file build_id + offset.
After profiling, a user space tool will look up these functions with
build_id (to find the binary or shared library) and the offset.
I also updated bcc/cc library for the stackmap (no python/lua support yet).
You can find the work at:
1. When kernel stack is added to stackmap with build_id, use fallback
mechanism to store ip (status == BPF_STACK_BUILD_ID_IP).
Changes v4 -> v5:
1. Only allow build_id lookup in non-nmi context. Added comment and
commit message to highlight this limitation.
2. Minor fix reported by kbuild test robot.
Changes v3 -> v4:
1. Add fallback when build_id lookup failed. In this case, status is set
to BPF_STACK_BUILD_ID_IP, and ip of this entry is saved.
2. Handle cases where vma is only part of the file (vma->vm_pgoff != 0).
Thanks to Teng for helping me identify this issue!
3. Address feedbacks for previous versions.
====================
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Song Liu [Wed, 14 Mar 2018 17:23:22 +0000 (10:23 -0700)]
bpf: add selftest for stackmap with BPF_F_STACK_BUILD_ID
test_stacktrace_build_id() is added. It accesses tracepoint urandom_read
with "dd" and "urandom_read" and gathers stack traces. Then it reads the
stack traces from the stackmap.
urandom_read is a statically link binary that reads from /dev/urandom.
test_stacktrace_build_id() calls readelf to read build ID of urandom_read
and compares it with build ID from the stackmap.
Signed-off-by: Song Liu <songliubraving@fb.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Song Liu [Wed, 14 Mar 2018 17:23:21 +0000 (10:23 -0700)]
bpf: extend stackmap to save binary_build_id+offset instead of address
Currently, bpf stackmap store address for each entry in the call trace.
To map these addresses to user space files, it is necessary to maintain
the mapping from these virtual address to symbols in the binary. Usually,
the user space profiler (such as perf) has to scan /proc/pid/maps at the
beginning of profiling, and monitor mmap2() calls afterwards. Given the
cost of maintaining the address map, this solution is not practical for
system wide profiling that is always on.
This patch tries to solve this problem with a variation of stackmap. This
variation is enabled by flag BPF_F_STACK_BUILD_ID. Instead of storing
addresses, the variation stores ELF file build_id + offset.
Build ID is a 20-byte unique identifier for ELF files. The following
command shows the Build ID of /bin/bash:
The search of build_id is limited to the first page of the file, and this
page should be in page cache. Otherwise, we fallback to store ip for this
entry (ip field in struct bpf_stack_build_id_offset). This requires the
build_id to be stored in the first page. A quick survey of binary and
dynamic library files in a few different systems shows that almost all
binary and dynamic library files have build_id in the first page.
Build_id is only meaningful for user stack. If a kernel stack is added to
a stackmap with BPF_F_STACK_BUILD_ID, it will automatically fallback to
only store ip (status == BPF_STACK_BUILD_ID_IP). Similarly, if build_id
lookup failed for some reason, it will also fallback to store ip.
User space can access struct bpf_stack_build_id_offset with bpf
syscall BPF_MAP_LOOKUP_ELEM. It is necessary for user space to
maintain mapping from build id to binary files. This mostly static
mapping is much easier to maintain than per process address maps.
Note: Stackmap with build_id only works in non-nmi context at this time.
This is because we need to take mm->mmap_sem for find_vma(). If this
changes, we would like to allow build_id lookup in nmi context.
Signed-off-by: Song Liu <songliubraving@fb.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Quentin Monnet [Fri, 9 Mar 2018 07:46:33 +0000 (23:46 -0800)]
bpf: comment why dots in filenames under BPF virtual FS are not allowed
When pinning a file under the BPF virtual file system (traditionally
/sys/fs/bpf), using a dot in the name of the location to pin at is not
allowed. For example, trying to pin at "/sys/fs/bpf/foo.bar" will be
rejected with -EPERM.
This check was introduced at the same time as the BPF file system
itself, with commit b2197755b263 ("bpf: add support for persistent
maps/progs"). At this time, it was checked in a function called
"bpf_dname_reserved()", which made clear that using a dot was reserved
for future extensions.
This function disappeared and the check was moved elsewhere with commit 0c93b7d85d40 ("bpf: reject invalid names right in ->lookup()"), and the
meaning of the dot ban was lost.
The present commit simply adds a comment in the source to explain to the
reader that the usage of dots is reserved for future usage.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Daniel Borkmann [Fri, 9 Mar 2018 09:23:00 +0000 (10:23 +0100)]
Merge branch 'bpf-tools-makefile-improvements'
Jiri Benc says:
====================
Currently, 'make bpf' in the tools/ directory does not provide the
standard quiet output except for bpftool (which is however listed
with a wrong directory). Worse, it does not respect the build output
directory.
The 'make bpf_install' does not work as one would expect, either.
It installs unconditionally to /usr/bin without respecting DESTDIR
and prefix.
This patchset improves that behavior.
====================
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Jiri Benc [Thu, 8 Mar 2018 22:00:41 +0000 (23:00 +0100)]
tools: bpf: silence make by not deleting intermediate file
Even in quiet mode, make finishes with
rm tools/bpf/bpf_exp.lex.c
That's because it considers the file to be intermediate. Silence that by
mentioning the lex.c file instead of the lex.o file; the dependency still
stays.
Signed-off-by: Jiri Benc <jbenc@redhat.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Jiri Benc [Thu, 8 Mar 2018 22:00:37 +0000 (23:00 +0100)]
tools: bpf: consistent make bpf_install
Currently, make bpf_install in tools/ does not respect DESTDIR. Moreover, it
installs to /usr/bin/ unconditionally.
Let it respect DESTDIR and allow prefix to be specified. Also, to be more
consistent with bpftool and with the usual customs, default the prefix to
/usr/local instead of /usr.
Signed-off-by: Jiri Benc <jbenc@redhat.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
When building bpf tool, gcc emits piles of warnings:
prog.c: In function ‘prog_fd_by_tag’:
prog.c:101:9: warning: missing initializer for field ‘type’ of ‘struct bpf_prog_info’ [-Wmissing-field-initializers]
struct bpf_prog_info info = {};
^
In file included from /home/storage/jbenc/git/net-next/tools/lib/bpf/bpf.h:26:0,
from prog.c:47:
/home/storage/jbenc/git/net-next/tools/include/uapi/linux/bpf.h:925:8: note: ‘type’ declared here
__u32 type;
^
As these warnings are not useful, switch them off.
Signed-off-by: Jiri Benc <jbenc@redhat.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Daniel Borkmann [Thu, 8 Mar 2018 01:22:34 +0000 (02:22 +0100)]
Merge branch 'bpf-perf-sample-addr'
Teng Qin says:
====================
These patches add support that allows bpf programs attached to perf events to
read the address values recorded with the perf events. These values are
requested by specifying sample_type with PERF_SAMPLE_ADDR when calling
perf_event_open().
The main motivation for these changes is to support building memory or lock
access profiling and tracing tools. For example on Intel CPUs, the recorded
address values for supported memory or lock access perf events would be
the access or lock target addresses from PEBS buffer. Such information would
be very valuable for building tools that help understand memory access or
lock acquire pattern.
====================
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Teng Qin [Tue, 6 Mar 2018 18:55:02 +0000 (10:55 -0800)]
samples/bpf: add example to test reading address
This commit adds additional test in the trace_event example, by
attaching the bpf program to MEM_UOPS_RETIRED.LOCK_LOADS event with
PERF_SAMPLE_ADDR requested, and print the lock address value read from
the bpf program to trace_pipe.
Signed-off-by: Teng Qin <qinteng@fb.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Teng Qin [Tue, 6 Mar 2018 18:55:01 +0000 (10:55 -0800)]
bpf: add support to read sample address in bpf program
This commit adds new field "addr" to bpf_perf_event_data which could be
read and used by bpf programs attached to perf events. The value of the
field is copied from bpf_perf_event_data_kern.addr and contains the
address value recorded by specifying sample_type with PERF_SAMPLE_ADDR
when calling perf_event_open.
Signed-off-by: Teng Qin <qinteng@fb.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Eric Dumazet [Wed, 7 Mar 2018 16:43:19 +0000 (08:43 -0800)]
ip6mr: remove synchronize_rcu() in favor of SOCK_RCU_FREE
Kirill found that recently added synchronize_rcu() call in
ip6mr_sk_done()
was slowing down netns dismantle and posted a patch to use it only if
the socket
was found.
I instead suggested to get rid of this call, and use instead
SOCK_RCU_FREE
We might later change IPv4 side to use the same technique and unify
both stacks. IPv4 does not use synchronize_rcu() but has a call_rcu()
that could be replaced by SOCK_RCU_FREE.
Tested:
time for i in {1..1000}; do unshare -n /bin/false;done
Before : real 7m18.911s
After : real 10.187s
Fixes: 8571ab479a6e ("ip6mr: Make mroute_sk rcu-based") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Kirill Tkhai <ktkhai@virtuozzo.com> Cc: Yuval Mintz <yuvalm@mellanox.com> Reviewed-by: Kirill Tkhai <ktkhai@virtuozzo.com> Signed-off-by: David S. Miller <davem@davemloft.net>
A couple of enhancements to the rds zerocop code
- patch 1 refactors rds_message_copy_from_user to pull the zcopy logic
into its own function
- patch 2 drops the usage sk_buff to track MSG_ZEROCOPY cookies and
uses a simple linked list (enhancement suggested by willemb during
code review)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
rds: use list structure to track information for zerocopy completion notification
Commit 401910db4cd4 ("rds: deliver zerocopy completion notification
with data") removes support fo r zerocopy completion notification
on the sk_error_queue, thus we no longer need to track the cookie
information in sk_buff structures.
This commit removes the struct sk_buff_head rs_zcookie_queue by
a simpler list that results in a smaller memory footprint as well
as more efficient memory_allocation time.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com> Acked-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
rds: refactor zcopy code into rds_message_zcopy_from_user
Move the large block of code predicated on zcopy from
rds_message_copy_from_user into a new function,
rds_message_zcopy_from_user()
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com> Acked-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Remove VLA usage and change the 'len' argument to a u8 and use a 256
byte buffer on the stack. Notice that these lengths are limited by the
encoding field in the VPD structure, which is a u8 [1].
Fix the SO_ZEROCOPY switch case on sock_setsockopt() avoiding the
ret values to be overwritten by the one set on the default case.
Fixes: 28190752c7092 ("sock: permit SO_ZEROCOPY on PF_RDS socket") Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com> Acked-by: Willem de Bruijn <willemb@google.com> Acked-by: Sowmini Varadhan <sowmini.varadhan@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This series adds unicast filtering support to the Marvell PPv2 controller.
This is implemented using the header parser cababilities of the PPv2,
which allows for generic packet filtering based on matching patterns in
the packet headers.
PPv2 controller only has 256 of these entries, and we need to share them
with other features, such as VLAN filtering.
For each interface, we have 5 entries dedicated to unicast filtering (the
controller's own address, and 4 other), and 21 to multicast filtering.
When this number is reached, the controller switches to unicast or
multicast promiscuous mode.
The first patch reworks the function that adds and removes addresses to the
filter. This is preparatory work to ease UC filter implementation.
The second patch adds the UC filtering feature.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell PPv2 controller can be used to implement packet filtering based
on the destination MAC address. This is already used to implement
multicast filtering. This patch adds support for Unicast filtering.
Filtering is based on so-called "TCAM entries" to implement filtering.
Due to their limited number and the fact that these are also used for
other purposes, we reserve 80 entries for both unicast and multicast
filters. On top of the broadcast address, and each interface's own MAC
address, we reserve 25 entries per port, 4 for unicast filters, 21 for
multicast.
Whenever unicast or multicast range for one port is full, the filtering
is disabled and port goes into promiscuous mode for the given type of
addresses.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: mvpp2: Simplify MAC filtering function parameters
The mvpp2_prs_mac_da_accept function takes into parameter both the
struct representing the controller and the port id. This is meaningful
when we want to create TCAM entries for non-initialized ports, but in
this case we expect the port to be initialized before starting adding or
removing MAC addresses to the per-port filter.
This commit changes the function so that it takes struct mvpp2_port as
a parameter instead.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hovold [Wed, 7 Mar 2018 09:46:58 +0000 (10:46 +0100)]
net: cdc_eem: clean up bind error path
Drop bogus call to usb_driver_release_interface() from an error path in
the usbnet bind() callback, which is called during interface probe. At
this point the interface is not bound and usb_driver_release_interface()
returns early.
Also remove the bogus call to clear the interface data, which is owned
by the usbnet driver and would not even have been set by the time bind()
is called.
Signed-off-by: Johan Hovold <johan@kernel.org> Acked-by: Oliver Neukum <oneukum@suse.com> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hovold [Wed, 7 Mar 2018 09:46:57 +0000 (10:46 +0100)]
net: kalmia: clean up bind error path
Drop bogus call to usb_driver_release_interface() from an error path in
the usbnet bind() callback, which is called during interface probe. At
this point the interface is not bound and usb_driver_release_interface()
returns early.
Also remove the bogus call to clear the interface data, which is owned
by the usbnet driver and would not even have been set by the time bind()
is called.
Signed-off-by: Johan Hovold <johan@kernel.org> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
This series consists of some fixes and refactors for the mlx5 drivers,
especially around the FPGA and flow steering. Most of them are trivial
fixes and are the foundation of allowing IPSec acceleration from user-space.
We use flow steering abstraction in order to accelerate IPSec packets.
When a user creates a steering rule, [s]he states that we'll carry an
encrypt/decrypt flow action (using a specific configuration) for every
packet which conforms to a certain match. Since currently offloading these
packets is done via FPGA, we'll add another set of flow steering ops.
These ops will execute the required FPGA commands and then call the
standard steering ops.
In order to achieve this, we need that the commands will get all the
required information. Therefore, we pass the fte object and embed the
flow_action struct inside the fte. In addition, we add the shim layer
that will later be used for alternating between the standard and the
FPGA steering commands.
Some fixes, like " net/mlx5e: Wait for FPGA command responses with a timeout"
are very relevant for user-space applications, as these applications could
be killed, but we still want to wait for the FPGA and update the kernel's
database.
Regards,
Aviad and Matan
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefano Brivio [Tue, 6 Mar 2018 21:16:27 +0000 (22:16 +0100)]
selftests: net: Introduce first PMTU test
One single test implemented so far: test_pmtu_vti6_exception
checks that the PMTU of a route exception, caused by a tunnel
exceeding the link layer MTU, is affected by administrative
changes of the tunnel MTU. Creation of the route exception is
checked too.
Requested-by: David Ahern <dsahern@gmail.com> Signed-off-by: Stefano Brivio <sbrivio@redhat.com> Acked-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Fengguang Wu [Tue, 6 Mar 2018 18:23:23 +0000 (02:23 +0800)]
enic: fix boolreturn.cocci warnings
drivers/net/ethernet/cisco/enic/vnic_dev.c:1294:9-10: WARNING: return of 0/1 in function 'vnic_dev_capable_udp_rss' with return type bool
Return statements in functions returning bool should use
true/false instead of 1/0.
Generated by: scripts/coccinelle/misc/boolreturn.cocci
Fixes: 48398b6e7065 ("enic: set UDP rss flag") CC: Govindarajulu Varadarajan <gvaradar@cisco.com> Signed-off-by: Fengguang Wu <fengguang.wu@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/dsa/mv88e6xxx/serdes.c:66:9-10: WARNING: return of 0/1 in function 'mv88e6352_port_has_serdes' with return type bool
Return statements in functions returning bool should use
true/false instead of 1/0.
Generated by: scripts/coccinelle/misc/boolreturn.cocci
Fixes: eb755c3f6b7d ("net: dsa: mv88e6xxx: Add helper to determining if port has SERDES") CC: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Fengguang Wu <fengguang.wu@intel.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Tue, 6 Mar 2018 09:56:31 +0000 (10:56 +0100)]
net: unpollute priv_flags space
the ipvlan device driver defines and uses 2 bits inside the priv_flags
net_device field. Such bits and the related helper are used only
inside the ipvlan device driver, and the core networking does not
need to be aware of them.
This change moves netif_is_ipvlan* helper in the ipvlan driver and
re-implement them looking for ipvlan specific symbols instead of
using priv_flags.
Overall this frees two bits inside priv_flags - and move the following
ones to avoid gaps - without any intended functional change.
Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
net: phy: remove phy_error from phy_disable_interrupts
All callers of phy_disable_interrupts() call phy_error() in the error
case. Therefore we don't need to do this within the function too.
This change also allows us to use phy_disable_interrupts() in code
holding phydev->lock (because phy_error() takes this lock).
Make use of this in phy_stop().
v2:
- splitted into two separate patches
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Mon, 5 Mar 2018 21:34:27 +0000 (22:34 +0100)]
net: phy: remove phy_error from phy_disable_interrupts
All callers of phy_disable_interrupts() call phy_error() in the error
case. Therefore we don't need to do this within the function too.
This change also allows us to use phy_disable_interrupts() in code
holding phydev->lock (because phy_error() can take this lock).
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Prashant Bhole [Tue, 6 Mar 2018 08:31:32 +0000 (17:31 +0900)]
selftests/net: fix in_netns.sh script
execute the subprocess in netns using 'ip netns exec'
Fixes: cc30c93fa020 ("selftests/net: ignore background traffic in psock_fanout") Signed-off-by: Prashant Bhole <bhole_prashant_q7@lab.ntt.co.jp> Acked-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: mvpp2: mvpp2_check_hw_buf_num() can be static
Fixes: effbf5f58d64 ("net: mvpp2: update the BM buffer free/destroy logic") Signed-off-by: Fengguang Wu <fengguang.wu@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
There are two compatibility strings for mv88e6xxx, but it isn't clear
from the documentation why only those two exist when the mv88e6xxx driver
supports more than the 6085 and 6190. Briefly describe how the compatible
property is used, and provide guidance on which to use.
The model list comes from looking at port_base_addr values (0x0 vs 0x10)
in drivers/net/dsa/mv88e6xxx/chip.c.
Signed-off-by: Brandon Streiff <brandon.streiff@ni.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
tipc: bcast: use true and false for boolean values
Assign true or false to boolean variables instead of an integer value.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com> Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 7 Mar 2018 17:05:56 +0000 (12:05 -0500)]
Merge branch '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
1GbE Intel Wired LAN Driver Updates 2018-03-05
This series contains updates to igb only.
Corinna Vinschen adds the support for trusted VFs into the igb driver.
Mika fixes an issue where PCIe device is physically unplugged can cause
a kernel crash. This issue is that netif_device_detach() is called in
these cases, which prevents netif_unregister() from bringing the device
down properly.
Christophe JAILLET fixes an issue with igb where HWTSTAMP_TX_ON was
being handled like a bit mask and not a value.
v2: dropped the e1000e fix from the series since I will be pushing it
through David Miller's net tree.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 7 Mar 2018 16:44:43 +0000 (11:44 -0500)]
Merge branch 'lan743x-driver'
Bryan Whitehead says:
====================
lan743x: Add new lan743x driver
Add new lan743x driver.
The lan743x from Microchip Technologies Inc,
is a PCIe to Gigabit Ethernet Controller.
Updates for V4:
Patch 1/2 - Applied community suggestions
convert to using module_pci_driver
Updates for V3:
Patch 1/2 - Applied community suggestions
removed initialization tracking flags.
converted to 64 bit statistics.
converted tx clean up tasklet to napi.
Updates for V2:
Patch 1/2 - Applied community suggestions
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Bryan Whitehead [Mon, 5 Mar 2018 19:23:30 +0000 (14:23 -0500)]
lan743x: Add main source files for new lan743x driver
Add main source files for new lan743x driver
Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
SCTP_SENDALL: This flag, if set, will cause a one-to-many
style socket to send the message to all associations that
are currently established on this socket. For the one-to-
one style socket, this flag has no effect.
Note there is another msg_control option:
5.3.8. SCTP AUTH Information Structure (SCTP_AUTHINFO)
It's a little complicated, I will post it in another patchset after
this.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Mon, 5 Mar 2018 12:44:20 +0000 (20:44 +0800)]
sctp: add support for snd flag SCTP_SENDALL process in sendmsg
This patch is to add support for snd flag SCTP_SENDALL process
in sendmsg, as described in section 5.3.4 of RFC6458.
With this flag, you can send the same data to all the asocs of
this sk once.
Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Mon, 5 Mar 2018 12:44:19 +0000 (20:44 +0800)]
sctp: add support for SCTP_DSTADDRV4/6 Information for sendmsg
This patch is to add support for Destination IPv4/6 Address options
for sendmsg, as described in section 5.3.9/10 of RFC6458.
With this option, you can provide more than one destination addrs
to sendmsg when creating asoc, like sctp_connectx.
It's also a necessary send info for sctp_sendv.
Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Mon, 5 Mar 2018 12:44:18 +0000 (20:44 +0800)]
sctp: add support for PR-SCTP Information for sendmsg
This patch is to add support for PR-SCTP Information for sendmsg,
as described in section 5.3.7 of RFC6458.
With this option, you can specify pr_policy and pr_value for user
data in sendmsg.
It's also a necessary send info for sctp_sendv.
Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
When addressing a review comment in a early version of the offending
patch a comment where left in which should have been removed. Remove the
comment to keep it consistent with the code.
Fixes: 75efa06f457bbed3 ("ravb: add support for changing MTU") Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Kirill Tkhai [Thu, 1 Mar 2018 12:23:28 +0000 (15:23 +0300)]
net: Make account struct net to memcg
The patch adds SLAB_ACCOUNT to flags of net_cachep cache,
which enables accounting of struct net memory to memcg kmem.
Since number of net_namespaces may be significant, user
want to know, how much there were consumed, and control.
Note, that we do not account net_generic to the same memcg,
where net was accounted, moreover, we don't do this at all (*).
We do not want the situation, when single memcg memory deficit
prevents us to register new pernet_operations.
(*)Even despite there is !current process accounting already
available in linux-next. See kmalloc_memcg() there for the details.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Aviad Yehezkel [Sun, 18 Feb 2018 13:00:54 +0000 (15:00 +0200)]
net/mlx5: Flow steering cmd interface should get the fte when deleting
Previously, deleting a flow steering entry only got the index.
Since the FPGA implementation of FTE's deletion might need to dig
inside the FTE itself, we would like to get the FTE's context.
Changing the interface to pass the FTE context.
Aviad Yehezkel [Sun, 18 Feb 2018 11:17:17 +0000 (13:17 +0200)]
net/mlx5: Add empty egress namespace to flow steering core
Currently, we don't support egress flow steering namespace in mlx5
flow steering core implementation. However, when we want to encrypt
a packet, we model it as a flow steering rule in the egress path.
To overcome this, we add an empty egress namespace to flow steering.
This namespace is initialized only when ipsec support exists.
In the future, this will grow to a full blown full steering
implementation, resembling the ingress path.
Matan Barak [Sun, 20 Aug 2017 12:46:51 +0000 (15:46 +0300)]
net/mlx5: Add shim layer between fs and cmd
The shim layer allows each namespace to define possibly different
functionality for add/delete/update commands. The shim layer
introduced here, will be used to support flow steering with the FPGA.
Matan Barak [Wed, 16 Aug 2017 06:43:48 +0000 (09:43 +0300)]
{net,IB}/mlx5: Add has_tag to mlx5_flow_act
The has_tag member will indicate whether a tag action was specified
in flow specification.
A flow tag 0 = MLX5_FS_DEFAULT_FLOW_TAG is assumed a valid flow tag
that is currently used by mlx5 RDMA driver, whereas in HW flow_tag = 0
means that the user doesn't care about flow_tag. HW always provide
a flow_tag = 0 if all flow tags requested on a specific flow are 0.
So we need a way (in the driver) to differentiate between a user really
requesting flow_tag = 0 and a user who does not care, in order to be
able to report conflicting flow tags on a specific flow.
Boris Pismenny [Wed, 16 Aug 2017 06:33:30 +0000 (09:33 +0300)]
IB/mlx5: Pass mlx5_flow_act struct instead of multiple arguments
Group and pass all function arguments of parse_flow_attr call in one
common struct mlx5_flow_act.
This patch passes all the action arguments of parse_flow_attr in one common
struct mlx5_flow_act. It allows us to scale the number of actions without adding
new arguments to the function.
Signed-off-by: Matan Barak <matanb@mellanox.com> Signed-off-by: Boris Pismenny <borisp@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Acked-by: Jason Gunthorpe <jgg@mellanox.com>
Matan Barak [Sun, 19 Nov 2017 15:51:13 +0000 (15:51 +0000)]
net/mlx5: FPGA and IPSec initialization to be before flow steering
Some flow steering namespace initialization (i.e. egress namespace)
might depend on FPGA capabilities. Changing the initialization order
such that the FPGA will be initialized before flow steering.
Flow steering fs cmds initialization might depend on
IPSec capabilities. Changing the initialization order such
that the IPSec will be initialized before flow steering as well.
Davidlohr Bueso [Mon, 22 Jan 2018 17:21:37 +0000 (09:21 -0800)]
ia64/err-inject: Use get_user_pages_fast()
At the point of sysfs callback, the call to gup is
done without mmap_sem (or any lock for that matter).
This is racy. As such, use the get_user_pages_fast()
alternative and safely avoid taking the lock, if possible.
Signed-off-by: Davidlohr Bueso <dbueso@suse.de> Signed-off-by: Tony Luck <tony.luck@intel.com>
Matthew Wilcox [Mon, 19 Feb 2018 17:41:26 +0000 (09:41 -0800)]
ia64: Convert remaining atomic operations
While we've only seen inlining problems with atomic_sub_return(),
the other atomic operations could have the same problem. Convert all
remaining operations to use the same solution as atomic_sub_return().
Signed-off-by: Matthew Wilcox <mawilcox@microsoft.com> Signed-off-by: Tony Luck <tony.luck@intel.com>
Corentin Labbe [Wed, 14 Feb 2018 12:19:06 +0000 (12:19 +0000)]
ia64: convert unwcheck.py to python3
Since my system use python3 as default, arch/ia64/scripts/unwcheck.py no
longer run.
This patch convert it to the python3 syntax.
I have ran it with python2/python3 while printing values of
start/end/rlen_sum which could be impacted by this change and I see no difference.
Fixes: 94a47083522e ("scripts: change scripts to use system python instead of env") Signed-off-by: Corentin Labbe <clabbe@baylibre.com> Signed-off-by: Tony Luck <tony.luck@intel.com>
Linus Torvalds [Mon, 5 Mar 2018 19:57:06 +0000 (11:57 -0800)]
Merge tag 'linux-kselftest-4.16-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull kselftest fixes from Shuah Khan:
"A fix for regression in memory-hotplug install script that prevents
the test from running on the target"
* tag 'linux-kselftest-4.16-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests: memory-hotplug: fix emit_tests regression
1) Use an appropriate TSQ pacing shift in mac80211, from Toke
Høiland-Jørgensen.
2) Just like ipv4's ip_route_me_harder(), we have to use skb_to_full_sk
in ip6_route_me_harder, from Eric Dumazet.
3) Fix several shutdown races and similar other problems in l2tp, from
James Chapman.
4) Handle missing XDP flush properly in tuntap, for real this time.
From Jason Wang.
5) Out-of-bounds access in powerpc ebpf tailcalls, from Daniel
Borkmann.
6) Fix phy_resume() locking, from Andrew Lunn.
7) IFLA_MTU values are ignored on newlink for some tunnel types, fix
from Xin Long.
8) Revert F-RTO middle box workarounds, they only handle one dimension
of the problem. From Yuchung Cheng.
9) Fix socket refcounting in RDS, from Ka-Cheong Poon.
10) Don't allow ppp unit registration to an unregistered channel, from
Guillaume Nault.
11) Various hv_netvsc fixes from Stephen Hemminger.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (98 commits)
hv_netvsc: propagate rx filters to VF
hv_netvsc: filter multicast/broadcast
hv_netvsc: defer queue selection to VF
hv_netvsc: use napi_schedule_irqoff
hv_netvsc: fix race in napi poll when rescheduling
hv_netvsc: cancel subchannel setup before halting device
hv_netvsc: fix error unwind handling if vmbus_open fails
hv_netvsc: only wake transmit queue if link is up
hv_netvsc: avoid retry on send during shutdown
virtio-net: re enable XDP_REDIRECT for mergeable buffer
ppp: prevent unregistered channels from connecting to PPP units
tc-testing: skbmod: fix match value of ethertype
mlxsw: spectrum_switchdev: Check success of FDB add operation
net: make skb_gso_*_seglen functions private
net: xfrm: use skb_gso_validate_network_len() to check gso sizes
net: sched: tbf: handle GSO_BY_FRAGS case in enqueue
net: rename skb_gso_validate_mtu -> skb_gso_validate_network_len
rds: Incorrect reference counting in TCP socket creation
net: ethtool: don't ignore return from driver get_fecparam method
vrf: check forwarding on the original netdevice when generating ICMP dest unreachable
...
David S. Miller [Mon, 5 Mar 2018 17:55:55 +0000 (12:55 -0500)]
Merge branch 'mvpp2-jumbo-frames-support'
Antoine Tenart says:
====================
net: mvpp2: jumbo frames support
This series enable jumbo frames support in the Marvell PPv2 driver. The
first 2 patches rework the buffer management, then two patches prepare for
the final patch which adds the jumbo frames support into the driver.
This is based on top of net-next, and was tested on a mcbin.
Thanks!
Antoine
Since v1:
- Improved the Tx FIFO initialization comment.
- Improved the pool sanity check in mvpp2_bm_pool_use().
- Fixed pool related comments.
- Cosmetic fixes (used BIT() whenever possible).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefan Chulski [Mon, 5 Mar 2018 14:16:54 +0000 (15:16 +0100)]
net: mvpp2: jumbo frames support
This patch adds the support for jumbo frames in the Marvell PPv2 driver.
A third buffer pool is added with 10KB buffers, which is used if the MTU
is higher than 1518B for packets larger than 1518B. Please note only the
port 0 supports hardware checksum offload due to the Tx FIFO size
limitation.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
[Antoine: cosmetic cleanup, commit message] Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Antoine Tenart [Mon, 5 Mar 2018 14:16:53 +0000 (15:16 +0100)]
net: mvpp2: enable UDP/TCP checksum over IPv6
This patch adds the NETIF_F_IPV6_CSUM to the driver's features to enable
UDP/TCP checksum over IPv6. No extra configuration of the engine is
needed on top of the IPv4 counterpart, which already is in the features
list (NETIF_F_IP_CSUM).
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yan Markman [Mon, 5 Mar 2018 14:16:52 +0000 (15:16 +0100)]
net: mvpp2: use a data size of 10kB for Tx FIFO on port 0
This patch sets the Tx FIFO data size on port 0 to 10kB. This prepares
the PPv2 driver for the Jumbo frame support addition as the hardware
will need big enough Tx FIFO buffers when dealing with frames going
through an interface with an MTU of 9000.
Signed-off-by: Yan Markman <ymarkman@marvell.com>
[Antoine: commit message, small reworks.] Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>