Mark Brown [Wed, 1 Jun 2011 19:16:40 +0000 (20:16 +0100)]
ASoC: Use a lower detection rate when monitoring headphones on WM8915
We only need to increase the detection rate to maximum if we're monitoring
for button presses as the response times needed for user interaction there
are much lower.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@ti.com>
Mark Brown [Wed, 1 Jun 2011 18:17:02 +0000 (19:17 +0100)]
ASoC: Remove internally generated WM8915 supplies
DCVDD and MICVDD are intended to be (and almost always are) generated by
on-board LDOs which are transparently controlled by the driver so we
shouldn't really be requesting them from the regulator API. If the driver
is updated to support external supply of these then we will need to change
the way we handle this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@ti.com>
e1 = clk_get@p1(...);
... when != e1 = e2
when != clk_put(e1)
when any
if (...) { ... when != clk_put(e1)
when != if (...) { ... clk_put(e1) ... }
* return@p3 ...;
} else S
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Wed, 1 Jun 2011 13:45:58 +0000 (14:45 +0100)]
ASoC: Support edge triggered IRQs for WM8915
Really this should be something the IRQ core can cope with for us but since
it doesn't currently do so (at least for threaded interrupts like this) do
so in the driver. This allows us to run with interrupt controllers that
only support edge triggered interrupts.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@ti.com>
Axel Lin [Fri, 27 May 2011 15:30:53 +0000 (23:30 +0800)]
ASoC: Remove redundant freq assignment for max98095->sysclk/max98088->sysclk
Current implementation set max98095->sysclk/max98088->sysclk to freq twice.
Set it once is enough, this patch removes the first assignment in case
we may set invalid clock frequency to max98095->sysclk/max98088->sysclk.
Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Peter Hsiang <peter.hsiang@maxim-ic.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Stephen Warren [Thu, 26 May 2011 18:46:50 +0000 (12:46 -0600)]
ASoC: Tegra: Enable Kaen HP_MUTE at boot
We want the default state of the HP_MUTE signal to be asserted, so that
the headphones are muted before the first audio playback. Without this,
the headphones are left unmuted until shortly after the first audio
playback completes.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Stephen Warren [Thu, 26 May 2011 15:57:33 +0000 (09:57 -0600)]
ASoC: Fix dapm_is_shared_kcontrol so everything isn't shared
Commit af46800 ("ASoC: Implement mux control sharing") introduced
function dapm_is_shared_kcontrol.
When this function returns true, the naming of DAPM controls is derived
from the kcontrol_new. Otherwise, the name comes from the widget (and
possibly a widget's naming prefix).
A bug in the implementation of dapm_is_shared_kcontrol made it return 1
in all cases. Hence, that commit caused a change in control naming for
all controls instead of just shared controls.
Specifically, a control is always considered shared because it is always
compared against itself. Solve this by never comparing against the widget
containing the control being created.
Equally, controls should never be shared between DAPM contexts; when the
same codec is instantiated multiple times, the same kcontrol_new will be
used. However, the control should no be shared between the multiple
instances.
I tested that with the Tegra WM8903 driver:
* Shared is now mostly 0 as expected, and sometimes 1.
* The expected controls are still generated after this change.
However, I don't have any systems that have a widget/control naming
prefix, so I can't test that aspect.
Thanks for Jarkko Nikula for pointing out how to fix this.
Reported-by: Liam Girdwood <lrg@ti.com> Tested-by: Jarkko Nikula <jhnikula@gmail.com> Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Jarkko Nikula [Thu, 26 May 2011 13:32:18 +0000 (16:32 +0300)]
ASoC: Fix power down for widgetless per-card DAPM context case
Commit 52ba67b ("ASoC: Force all DAPM contexts into the same bias state")
powers up all the DAPM contexts in a card if any DAPM context becomes
active. Unfortunately power down newer happens if per-card DAPM context
doesn't have any widgets.
Reason for this is that power state of per-card DAPM context without
widgets is never cleared and thus all the DAPM contexts remain permanently
active. Test for widgetless calling DAPM context in dapm_power_widgets()
doesn't work for per-card DAPM context since power change is never
originating from widgetless per-card DAPM context.
Fix this by pre-clearing power state flag of non-codec DAPM context at the
beginning of power sequence.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Nicolas Ferre [Tue, 24 May 2011 09:51:16 +0000 (11:51 +0200)]
ASoC: sam9g20_wm8731: use the proper SYSCKL value
at91sam9g20 is providing master clock to wm8731: not using a crystal but an
external MCLK. We can avoid conflict and save power using WM8731_SYSCLK_MCLK as
we do not need oscillator to be powered.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The crystal oscillator is only enabled if the WM8731_SYSCLK_XTAL master clock
is specified. Fix the connected() struct snd_soc_dapm_route function to take
this into account. Oscillator is not enabled on machine that need it otherwise.
Machine drivers have to make sure that they use the proper SYSCLK value.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Nicolas Ferre [Thu, 26 May 2011 11:44:12 +0000 (13:44 +0200)]
ASoC: atmel_ssc_dai: fix ssc error path
We do not have to free a resource that is not allocated yet.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Nicolas Ferre [Thu, 26 May 2011 11:44:11 +0000 (13:44 +0200)]
ASoC: trivial: typo in atmel_pcm_dma_params strucutre comment
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Nicolas Ferre [Thu, 26 May 2011 11:44:10 +0000 (13:44 +0200)]
ASoC: trivial: typo in debug comment
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For cards that have two or more DAIs, snd_soc_resume's loop over all
DAIs ends up calling schedule_work(deferred_resume_work) once per DAI.
Since this is the same work item each time, the 2nd and subsequent
calls return 0 (work item already queued), and trigger the dev_err
message below stating that a work item may have been lost.
Solve this by adjusting the loop to simply calculate whether to run the
resume work immediately or defer it, and then call schedule work (or not)
one time based on that.
Note: This has not been tested in mainline, but only in chromeos-2.6.38;
mainline doesn't support suspend/resume on Tegra, nor does the mainline
Tegra ASoC driver contain multiple DAIs. It has been compile-checked in
mainline.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Daniel Mack [Wed, 25 May 2011 07:53:12 +0000 (09:53 +0200)]
ASoC: Fix comment in cs4270 codec driver
The comment does not reflect reality anymore since the multi-component
monster patch landed. Things are matched by names now, and not by
exporting and referencing a struct. Fix it to avoid confusion.
Signed-off-by: Daniel Mack <zonque@gmail.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Acked-by: Timur Tabi <timur@freescale.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Ben Gardiner [Wed, 25 May 2011 13:27:22 +0000 (09:27 -0400)]
ASoC: davinci-pcm: comments for the conversion to BATCH mode
In the previous commit 'ASoC: davinci-pcm: convert to BATCH mode', the phase
offset of 2 was mentioned in the commit message but not well commented in the
source.
Add descriptive comments of the phase offset with and without ping-pong
buffers enabled.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Ben Gardiner [Tue, 24 May 2011 18:50:20 +0000 (14:50 -0400)]
ASoC: davinci-pcm: convert to BATCH mode
The davinci-pcm driver's snd_pcm_ops pointer function currently calls into
the edma controller driver to read the current positions of the edma channels
to determine pos to return to the ALSA framework. In particular,
davinci_pcm_pointer() calls edma_get_position() and the latter has a comment
indicating that "Its channel should not be active when this is called" whereas
the channel is surely active when snd_pcm_ops.pointer is called.
The operation of davinci-pcm in capture and playback appears to follow close
the other pcm drivers who export SNDRV_PCM_INFO_BATCH except that davinci-pcm
does not report it's positions from pointer() using the last transferred
chunk. Instead it peeks directly into the edma controller to determine the
current position as discussed above.
Convert the davinci-pcm driver to BATCH mode: count the periods elapsed in the
prtd->period member and use its value to report the 'pos' to the alsa
framework in the davinci_pcm_pointer function.
There is a phase offset of 2 periods between the position used by dma setup
and the position reported in the pointer function. Either +2 in the dma
setup or -2 in the pointer function (with wrapping, both) accounts for this
offset -- I opted for the latter since it makes the first-time setup clearer.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca> Reviewed-by: Steven Faludi <stevenfaludi@nanometrics.ca> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Ben Gardiner [Tue, 24 May 2011 18:50:19 +0000 (14:50 -0400)]
ASoC: davinci-pcm: extract period elapsed functions
Extract functions that modify the prtd->period member in preparation for
conversion to BATCH mode playback.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca> Reviewed-by: Steven Faludi <stevenfaludi@nanometrics.ca> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Ben Gardiner [Tue, 24 May 2011 18:50:18 +0000 (14:50 -0400)]
ASoC: davinci-pcm: fix audible glitch on 2nd ping-pong playback
The release of the dma channels was being performed in prepare and there was a
edma_resume call for the asp-channel only being executed on START, RESUME and
PAUSE_RELEASE.
The mcasp on da850evm with ping-pong buffers enabled was exhibiting an audible
glitch on every playback after the first. It was determined through trial and
error that the following two changes fix this problem:
1) Move the edma_start calls from prepare to trigger and 2) reverse the order
of starting the asp and ram channels.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca> Reviewed-by: Steven Faludi <stevenfaludi@nanometrics.ca> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Ben Gardiner [Tue, 24 May 2011 18:50:17 +0000 (14:50 -0400)]
ASoC: davinci-pcm: increase the maximum channels
Based on the registration of davinci-mcasp.1 in the davinci-evm platform
setup for da830 and dm6467, davinci-pcm can handle more than the currently
reported maximum channels of 2.
Increase the maximum channels to 384 to match the maximum reported by
davinci-mcasp.1.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca> Reviewed-by: Steven Faludi <stevenfaludi@nanometrics.ca> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Update the .format member of the snd_pcm_hardware instances it registers to
reflect this capability.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca> Reviewed-by: Steven Faludi <stevenfaludi@nanometrics.ca> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Ben Gardiner [Tue, 24 May 2011 18:50:15 +0000 (14:50 -0400)]
ASoC: davinci-pcm: trivial: make ping-pong params setup symmetrical
The setup of the pong channel uses EDMA_CHAN_SLOT instead of & 0x3f as the
setup of the ping channel does.
Make the setup of ping and pong symmetric. There is no functional change
introduced by this patch.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca> Reviewed-by: Steven Faludi <stevenfaludi@nanometrics.ca> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Liam Girdwood [Tue, 24 May 2011 12:57:43 +0000 (13:57 +0100)]
ASoC: core - fix module reference counting for CPU DAIs
Currently CODEC and platform drivers have their module reference count
incremented soc_probe_dai_link() whilst CPU DAI drivers have their reference
count incremented in soc_bind_dai_link().
CPU DAIs should have their reference count incremented in soc_probe_dai_link()
just like the CODEC and platform drivers.
Signed-off-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Daniel Mack [Tue, 24 May 2011 12:10:32 +0000 (14:10 +0200)]
ASoC: fix raumfeld platform
Commit f0fba2ad (ASoC: multi-component - ASoC Multi-Component Support)
broke support for Raumfeld platforms as it didn't take into account the
different hardware features on individual devices.
In particular, Raumfeld speakers have no S/PDIF output, so the members
of the snd_soc_card struct must be set dynamically.
Signed-off-by: Daniel Mack <zonque@gmail.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: stable@kernel.org
Current FSI driver was using saved_xxx variable for suspend/resume.
OTOH, the start and stop of power/clock are controlled by
fsi_hw_startup/fsi_hw_shutdown in current FSI driver.
The all necessary registers value are set by fsi_hw_startup.
So, if fsi_hw_shutdown is called when "suspend" is generated,
and fsi_hw_startup is called at "resume",
the saved_xxx are not needed.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
FSIA/B ports is enabled by default when power-on,
and current FSI is supporting RuntimePM.
In addition, current fsi_module_init/kill doesn't care
simultaneous playback/recorde.
This mean FSI port control is not needed.
This patch remove fsi_module_init/kill
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ASoC: sh: fsi: remove pm_runtime from fsi_dai_set_fmt.
pm_runtime_get/put_sync were used to access FSI register in fsi_dai_set_fmt
which is called when ALSA probe.
But this register value will disappear after pm_runtime_put_sync
if platform is supporting RuntimePM.
To solve this issue, this patch adds new variable for format,
and remove pm_runtime_get/put_sync from fsi_dai_set_fmt.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some variables on this driver were a unclear naming,
and were different unit (byte, frame, sample).
And some functions had wrong name
(ex. it returned "sample width" but name was "fsi_get_frame_width").
This patch tidy-up this issue, and the minimum unit become "sample".
Special thanks to Takashi YOSHII.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Current FSI driver is using set_rate call back function which is for
master mode.
By this patch, it is used from fsi_set_master_clk.
This patch is preparation of cleanup suspend/resume patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Jarkko Nikula [Fri, 20 May 2011 12:47:40 +0000 (15:47 +0300)]
ASoC: core: Don't set "(null)" as a driver name
Commit 22de71b ("ASoC: core - allow ASoC more flexible machine name")
writes "(null)" to driver name string in struct snd_card if card->driver_name
is NULL. This causes segmentation faults with some user space ALSA utilities
like aplay and arecord.
Fix this by using the card->name if no driver name is specified.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ASoC: soc-cache: Cache a pointer to the last accessed rbnode
Whenever we are doing a read or a write through the rbtree code, we'll
cache a pointer to the rbnode. To avoid looking up the register
everytime we do a read or a write, we first check if it can be found in
the cached register block, otherwise we traverse the rbtree and finally
cache the rbnode for future use.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch prepares the ground for the actual rbtree optimization patch
which will save a pointer to the last accessed rbnode that was used
in either the read() or write() functions.
Each rbnode manages a variable length block of registers. There can be no
two nodes with overlapping blocks. Each block has a base register and a
currently top register, all the other registers, if any, lie in between these
two and in ascending order.
The reasoning behind the construction of this rbtree is simple. In the
snd_soc_rbtree_cache_init() function, we iterate over the register defaults
provided by the driver. For each register value that is non-zero we
insert it in the rbtree. In order to determine in which rbnode we need
to add the register, we first look if there is another register already
added that is adjacent to the one we are about to add. If that is the case
we append it in that rbnode block, otherwise we create a new rbnode
with a single register in its block and add it to the tree.
In the next patch, where a cached rbnode is used by both the write() and the
read() functions, we also check if the register we are about to add is in the
cached rbnode (the least recently accessed one) and if so we append it in that
rbnode block.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Stephen Warren [Mon, 16 May 2011 20:19:27 +0000 (14:19 -0600)]
ASoC: Tegra: Fix compile when debugfs not enabled
The prototype of the inline dummy version of tegra_i2s_debug_add
was not consistent with the real version.
Reported-by: Rhyland-Klein <rklein@nvidia.com> Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Stephen Warren [Thu, 19 May 2011 23:44:46 +0000 (17:44 -0600)]
ASoC: spdif-dit: Add missing MODULE_*
MODULE_ALIAS is required so that the module will auto-load based on a
platform_device registration in the board file.
While we're at it, add some other MODULE_*.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The davinci-i2s driver copies the platform data for playback and capture
sram sizes which is in turn used by davinci-pcm to allocate ping-pong
buffers.
Copy also the platform data in davinci-mcasp probe.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Dmitry Artamonow [Wed, 18 May 2011 15:25:09 +0000 (19:25 +0400)]
ASoC: Asahi Kasei AK4641 codec driver
A driver for the AK4641 codec used in iPAQ hx4700 and Glofiish M800
among others.
Signed-off-by: Harald Welte <laforge@gnumonks.org> Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com> Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Taylor Hutt [Wed, 18 May 2011 01:03:54 +0000 (18:03 -0700)]
ASoC: Max98095: Move existing NULL check before pointer dereference.
Visual inspection shows that max98095_put_eq_enum() and
max98095_put_bq_enum() each have a possible NULL deref of 'pdata'.
This change moves the NULL check above the use.
Signed-off-by: Taylor Hutt <thutt@chromium.org> Acked-by: Peter Hsiang <Peter.Hsiang@maxim-ic.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Enabling DEBUG_STRICT_USER_COPY_CHECKS causes the following
warning:
In file included from arch/x86/include/asm/uaccess.h:573,
from include/linux/poll.h:14,
from include/sound/pcm.h:29,
from include/sound/ac97_codec.h:31,
from sound/soc/soc-core.c:34:
In function 'copy_from_user',
inlined from 'codec_reg_write_file' at
sound/soc/soc-core.c:252:
arch/x86/include/asm/uaccess_64.h:65:
warning: call to 'copy_from_user_overflow' declared with
attribute warning: copy_from_user() buffer size is not provably
correct
presumably due to buf_size being signed causing GCC to fail to
see that buf_size can't become negative.
Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Jarkko Nikula [Fri, 13 May 2011 16:16:52 +0000 (19:16 +0300)]
ASoC: Fix wrong data type access in a few codec drivers
Commit fafd217 ("ASoC: Store a list of widgets in a DAPM mux/mixer kcontrol")
changed the control private data type that is passed to snd_soc_cnew when
creating dapm mixer and mux controls. Commit did not update a few codec
drivers that are using their own put callbacks and thus are accessing a
wrong data type.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com> Tested-by: Stephen Warren <swarren@nvidia.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Mon, 16 May 2011 01:02:53 +0000 (18:02 -0700)]
ASoC: Skip noop reconfiguration of WM8958 DSP2 algorithms
If we're setting the currently applied value for one of the DSP algorithm
configurations we can just skip all the handling as the control set is a
noop. This ensures we do not disrupt a running DSP.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@ti.com> Cc: stable@kernel.org
Sanjeev Premi [Wed, 11 May 2011 13:55:35 +0000 (19:25 +0530)]
ASoC: omap-mcbsp: Remove restrictive checks for cpu type
Current checks for cpu type were too restrictive leading
to failures for other silicons in same family.
The problem was found while testing audio playback on
AM37x and AM35x processors. But should exist on OMAP36xx
as well.
Signed-off-by: Sanjeev Premi <premi@ti.com>
cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
cc: Liam Girdwood <lrg@ti.com>
cc: Jarkko Nikula <jhnikula@gmail.com> Acked-by: Jarkko Nikula <jhnikula@gmail.com> Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@ti.com>
Peter Ujfalusi [Thu, 12 May 2011 10:04:55 +0000 (13:04 +0300)]
ASoC: omap-pcm: Period wakeup disabling on OMAP2+
Allow disabling ALSA period wakeup interrupts.
This can only be done on OMAP2+ (2/3/4), since there
we can chain the DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Jarkko Nikula <jhnikula@gmail.com> Signed-off-by: Liam Girdwood <lrg@ti.com>
Digital microphones can have some additional elements in their
audio path (like microphone bias). An input widget is required
for digital microphone CODEC driver to allow external connections
in machine drivers.
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com> Signed-off-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Randy Dunlap [Sun, 8 May 2011 16:48:24 +0000 (09:48 -0700)]
ASoC: fix wm8958-dsp2 printk format warnings
Fix printk format warnings in wm8958-dsp2.c:
sound/soc/codecs/wm8958-dsp2.c:103: warning: format '%d' expects type 'int', but argument 4 has type 'size_t'
sound/soc/codecs/wm8958-dsp2.c:111: warning: format '%d' expects type 'int', but argument 3 has type 'size_t'
sound/soc/codecs/wm8958-dsp2.c:144: warning: format '%d' expects type 'int', but argument 5 has type 'size_t'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Peter Ujfalusi [Mon, 2 May 2011 11:16:29 +0000 (14:16 +0300)]
MAINTAINERS: Update e-mail address for asoc/twl4030
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@ti.com>
Peter Ujfalusi [Tue, 3 May 2011 15:15:10 +0000 (18:15 +0300)]
ASoC: RX51: Update e-mail address
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Jarkko Nikula <jhnikula@gmail.com> Signed-off-by: Liam Girdwood <lrg@ti.com>
Peter Ujfalusi [Tue, 3 May 2011 15:14:43 +0000 (18:14 +0300)]
ASoC: omap-pcm: Update e-mail address
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Jarkko Nikula <jhnikula@gmail.com> Signed-off-by: Liam Girdwood <lrg@ti.com>
Peter Ujfalusi [Tue, 3 May 2011 15:14:06 +0000 (18:14 +0300)]
ASoC: omap-mcbsp: Update e-mail address
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Jarkko Nikula <jhnikula@gmail.com> Signed-off-by: Liam Girdwood <lrg@ti.com>
Peter Ujfalusi [Tue, 3 May 2011 15:12:41 +0000 (18:12 +0300)]
ASoC: tpa6130a2: Update e-mail address
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@ti.com>
Peter Ujfalusi [Tue, 3 May 2011 15:11:36 +0000 (18:11 +0300)]
ASoC: tlv320dac33: Update e-mail address
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@ti.com>
Mark Brown [Wed, 11 May 2011 12:34:53 +0000 (14:34 +0200)]
ASoC: Disable WM8994/58 microphone detection over suspend
It will be non-functional with the basises and clocks off anyway, if the
system needs microphone detection enabled over suspend then it should be
causing the CODEC to ignore suspend using the APIs for that to prevent
the biases being disabled.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@ti.com>
Mark Brown [Tue, 10 May 2011 21:33:48 +0000 (23:33 +0200)]
ASoC: Use spi_write() for SPI writes
do_spi_write() is just an open coded copy of do_spi_write() so we can
delete it and just call spi_write() directly. Indeed, as a result of
recent refactoring all the SPI write functions are just very long
wrappers around spi_write() which don't add anything except for some
pointless copies so we can just use spi_write() as the hw_write
operation directly. It should be as type safe to do this as it is to do
the same thing with I2C and it saves us a bunch of code.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@ti.com>
Mark Brown [Tue, 10 May 2011 21:55:21 +0000 (23:55 +0200)]
ASoC: Remove byte swap in 4x12 SPI write
snd_soc_4_12_spi_write() contains a byte swap. Since this code was written
for an Analog CODEC on a Blackfin reference board it appears that this is
done because while Blackfin is little endian the CODEC is big endian (as
are most CODECs).
Push this up into the generic 4x12 write function and use cpu_to_be16() to
do the byte swap so things are more regular and things work on both CPU
endiannesses.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@ti.com>
Stephen Warren [Mon, 9 May 2011 22:32:03 +0000 (16:32 -0600)]
ASoC: WM8903: Fix Digital Capture Volume range
Increase the range of the Digital Capture Volume control to be 120 steps.
Each step is 0.75dB, and the range starts at -72dB, giving a max setting
of 18dB, which matches the latest datasheet, to the precision of the step
size.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The SSM2604 is basically a lightweight variant of the SSM2602 with a compatible
register layout. Thus we can easily support both devices by the same driver,
by providing a slightly set of controls, widgets and routes.
Compared to the SSM2602 the SSM2604 has no microphone input and no headphone
output.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It is not required to have the codec powered at this stage and DAPM will power
the ADC and DAC down again after probe has run anyway.
Thus we avoid some unnecessary writes by this change.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Define POWER_OFF_ON_STANDBY cause trobles when trying to get some
sound from codec because code for bias setup was not compiled
(define wasn't defined). This define was removed in commit: cc3202f5 but again introduced by commit: f0fba2ad1 which then
completely break codec functionality so remove it again.
Signed-off-by: Marek Belisko <marek.belisko@open-nandra.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: stable@kernel.org
There are currently two controls which allow selecting the capture source, one
as a normal control, the other as part of a DAPM_MUX widget.
Remove the normal control.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
projects / mirror_ubuntu-jammy-kernel.git / log